Through a bug in the tun driver, I noticed that virtio_net is
producing bogus hdr_len values. In particular, it only includes
the IP header in the linear area, and excludes the entire TCP
header. This causes the TCP header to be copied twice for each
packet. (The bug omitted the second copy :)
This patch corrects this.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes an initialization error; the chip negotiates gigabit, but
the driver mistakenly handled it as 100Mb.
Changes based on both SiS own GPL driver and forcedeth.
Hopefully should fix
http://bugzilla.kernel.org/show_bug.cgi?id=9735http://bugzilla.kernel.org/show_bug.cgi?id=11149
Signed-off-by: Riccardo Ghetta <birrachiara@tin.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Corrected dma sync handling on small packets. Should fix
http://bugzilla.kernel.org/show_bug.cgi?id=11509
Note:
While this bug was reported only on x86_64, it could have affected
any architecture.
Signed-off-by: Riccardo Ghetta <birrachiara@tin.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some firmware mailbox commands require the firmware to
communicate with the FCoE driver running on another
PCI function. This can potentially take several seconds.
This wait is done in process context only.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 8 banks of 'sub-registers' each of which are accessed
through address/data register pair. An example would be reading
flash or the xgmac. Accessing these require the driver to wait for
a ready bit before writing the address and then accessing the data.
This patch increases the timeout to 100us to prevent timeouts
that have been seen on some platforms.
These register are accessed in process context only.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since an FCoE function shares a port with this NIC function, the
jumbo settings must always be in place. This patch causes the
hardware to be set up for jumbo if it is not already done.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each firmware mailbox command can have a different number of
valid data elements. When waiting for a mailbox command to
complete it the process passes it's element count and
waits for the completion. It is possible that while waiting
an unrelated firmware async event (AE) can arrive. When this
happens, the handler will over write the element count
with the value for the newly arrived AE. This can cause
the mailbox command to not get all of it's data.
This patch restores original mailbox count at the end
of the handler.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check status on every iteration of event handler loop and exit
if an error occurred. If an error occurred then recover process
will be queued so this loop should no continue.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smsc911x_drv_remove() function is declared with __devexit, so the
assignment to the driver structure needs __devexit_p() wrappings to prevent
build failure when hotplug is disabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smsc911x driver works fine on Blackfin systems, so add it to the arch
list in the Kconfig.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With all the last patchsets going in for 82599 feature enablement, the
driver version needs to be increased for better identification.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 has a FW running that helps manage the internal SFI PHY. There are
also a number of pre-production samples of these SFI-based devices in the
field. This patch adds a check to look for the firmware running on all
SFP+ based adapters, and displays a warning to the system log if a
pre-production adapter is identified. The driver will continue loading
though, with no functional degradation.
Also remove an old function prototype from ixgbe_82599.c that isn't being
used.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rearranges the ixgbe_ring struct to make better use of
cacheline efficiency.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables Flow Director's ATR functionality to the main base
driver for 82599.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the functions for ixgbe to initialize Flow Director. It
also has the function APIs to add Flow Director filters from the base
driver. This also includes ATR, Application Targeted Routing, which is a
feature set of Flow Director. This is the hash-based mechanism to
automatically identify flows and add filters based on the hash, and direct
the Rx of that flow back to that same CPU.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow Director is a Rx filter mechanism designed to match Rx flows back to
the same CPU that the flow's Tx occurred from. This patch adds the first
piece, the defines for the hardware registers, to enable this feature in
82599 hardware.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a second feature flag variable to use for future feature
expansion. Add HW RSC to this new feature flags variable.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the tx cleanup processing out of the MSI-X interrupt
processing and gives it it's own napi routine. This allows the driver to
process TX cleanup in a polling context instead of in an interrupt context
which prevents TX from starving RX.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The v_idx value was being used as both a bitmask and an index. This change
makes it so that the q_vector contains the index and allows for much of the
code to be simplified since disabling a q_vector involves only clearing one
bit in the interrupt bitmask.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver so that it uses rx_buffer_info->dma to
determine if it needs to unmap the page instead of sh_info->nr_frags. This
helps to prevent a cache line miss when receiving small packets as the
rx_buffer_info data should already be in the cache.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool support to change advertised link modes/autoneg settings of
82599 multispeed fiber adapters.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix autoneg restart issues in flow control path which might create
endless link flickering due to known timing issues with 82599
adapters.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakakla@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 supports multispeed fiber optical modules (10Gbps/1Gbps). Some
scenarios can cause the autotry mechanism to not negotiate link properly.
What needs to happen is the driver must flap the Tx laser to induce an Rx
Loss of Signal on the link partner. This will restart the autotry
mechanism to get link into a known state. The software definable pin (SDP)
3 on the 0x10fb NIC is wired to cause a Tx LOS event, which triggers the
Rx LOS we require.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the ethtool internal test engine.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reprogramming the 82599 analog PHY to either SFI optical or Direct
Attach Twinax, we need to restart the DSP in the PHY. The current method
can cause contention with our FW which is managing PHY state, and will
cause unexpected link flaps. This patch fixes the DSP restart by issuing
an AN_RESTART in the MAC, which will properly propagate the DSP restart to
the PHY. This ensures we don't collide with the FW.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 82599 KX4 device defaults to legacy power management, or APME. This
puts the device into ACPI mode, which allows more robust WoL setups to
work properly.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1f87f7d3 (cfg80211: add rfkill support) added ERFKILL
to asm-generic/errno.h, but alpha, mips, parisc and sparc use
their own numbering scheme and do not include asm-generic/errno.h.
We need to add definition of ERFKILL for them.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the forcedeth device ids from pci_ids.h
The forcedeth driver uses the device id constants directly in its source
file.
[ Need to keep PCI_DEVICE_ID_NVIDIA_NVENET_15 in order to keep
drivers/pci/quirks.c building -DaveM ]
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new device id for mcp89 chipset.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the device id macros and instead uses the constants
directly.
The areas in which logic expressions where using the macros now instead
use feature/workaround flags.
No new functionality has been introduced in this patch, only clean up of
flags and macros.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My mistake, I should have added that when cleaning up
rfkill and changing wimax.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes code (deprecated by "cfg80211: add rfkill support" )
main.c: In function 'ar9170_op_config':
main.c:1306: warning: '__IEEE80211_CONF_CHANGE_RADIO_ENABLED'
is deprecated (declared at include/net/mac80211.h:551)
and a useless device state.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixing a comment in the code describing this module parameter.
The description printed when user runs "modinfo" is correct.
Reported-by: Jiajia Zheng <jiajia.zheng@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcoding the link quality parameters inside the functions,
adding #define in iwl-commands.h to shared by different functions.
Also include the valid range for number of link quality parameters.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wait until ucode is loaded and driver receive ALIVE_REPLY then switch
to ICT interrupt. This ensures we receive all interrupts indicating
successful ucode load.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch fixes the bug at
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1903
when SW rfkill is invoked by 'iwconfig txpower off',
the existing connection disassociates and led off command is sent
to the device which returns error as rfkill is 'true'.
Patch fixes this by just avoiding sending the led off/on command when
disassociated. The main purpose of the led_disassociate callback
is to start or stop the blinking.
There are three states in led
1) Always on when radio is on
2) Always off when radio is off
3) blink when associated and if there is some traffic.
In this callback 'allow_blinking' needs to be set false
when associated, as LED will be always on.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Port "iwlcore: Allow skb allocation from tasklet." to 3945
If RX queue becomes empty then we need to restock the queue from
tasklet to prevent ucode from starving. A caller to iwl_rx_allocate
will decide if allocated buffer should come from GFP_ATOMIC or
GFP_KERNEL.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unifies 3945 and AGN station management
It also removes useless struct iwl_station_mgmt ops
and cleanups a bit the interface
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use printk format specifier for MAC address.
Remove DECALRE_MAC_BUF and print_mac() usage in the driver.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I added socket accounting to tun I inadvertently introduced
spurious wake-up events that kills qemu performance. The problem
occurs when qemu polls on the tun fd for read, and then transmits
packets. For each packet transmitted, we will wake up qemu even
if it only cares about read events.
Now this affects all sockets, but it is only a new problem for
tun. So this patch tries to fix it for tun first and we can then
look at the problem in general.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_mc_drop_socket() method is declared in linux/igmp.h, which
is included anyhow in af_inet.c. So there is no need for this declaration.
This patch removes it from af_inet.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it stands skb fraglists can get past the check in dev_queue_xmit
if the skb is marked as GSO. In particular, if the packet doesn't
have the proper checksums for GSO, but can otherwise be handled by
the underlying device, we will not perform the fraglist check on it
at all.
If the underlying device cannot handle fraglists, then this will
break.
The fix is as simple as moving the fraglist check from the device
check into skb_gso_ok.
This has caused crashes with Xen when used together with GRO which
can generate GSO packets with fraglists.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use generic MDIO generic values.
Based on Ben Hutchings'review comments.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* iwm doesn't depend on cfg80211 or wireless extensions
* rndis wlan selects cfg80211 - needs to depend
* mac80211 selects cfg80211 - needs to depend
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add some blurb about /dev/rfkill to the documentation and
fix the "transmiter" spelling error.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Herbert Xu