[ Upstream commit f765c59c5a ]
The dp and ufp are defined as bool type, the return value type of
function extcon_get_state should be int, so the type of dp and ufp
are modified to int.
./drivers/phy/rockchip/phy-rockchip-typec.c:827:12-14: WARNING: Unsigned expression compared with zero: dp > 0.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3962
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230213035709.99027-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ca651df07 ]
The existing logic in tcphy_get_mode() can cause the phy to be
incorrectly configured to USB UFP or DisplayPort mode when
extcon_get_state returns an error code.
extcon_get_state() can return 0, 1, or a negative error code.
It is possible to get into the failing state with an extcon driver
which does not support the extcon connector id specified as the
second argument to extcon_get_state().
tcphy_get_mode()
->extcon_get_state()
-->find_cable_index_by_id()
--->return -EINVAL;
Fixes: e96be45cb8 ("phy: Add USB Type-C PHY driver for rk3399")
Signed-off-by: Neill Kapron <nkapron@google.com>
Reviewed-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230126001013.3707873-1-nkapron@google.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5daba914da ]
The clk_disable_unprepare() should be called in the error handling of
rockchip_usb2phy_power_on().
Fixes: 0e08d2a727 ("phy: rockchip-inno-usb2: add a new driver for Rockchip usb2phy")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Link: https://lore.kernel.org/r/20221205115823.16957-1-shangxiaojing@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The rockchip,pipe-grf property is only used on rk3588, but not on
rk3568. Therefore this property is not present on rk3568 devices,
leading to the following message:
rockchip-snps-pcie3-phy fe8c0000.phy: failed to find rockchip,pipe_grf regmap
Fix that by only looking for this property on rk3588.
Fixes: 2e9bffc4f7 ("phy: rockchip: Support PCIe v3")
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Link: https://lore.kernel.org/r/20220927051752.53089-1-aurelien@aurel32.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the Rockchip RK3568 DSI-DPHY. Registers were taken from
the BSP kernel driver and wherever possible cross referenced with the
TRM.
Refactor the code to allow the different compatible strings to set
either a max 1GHz timing table (all existing hardware) or a max 2.5GHz
timing table (the new RK356x). This works (for me) on both an RK3326
(PX30) and a new RK3566 device.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20220919164616.12492-3-macroalpha82@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The otg sync state patch reuses the ret variable, but fails to set it to
zero after use. This leads to a situation when the otg port is in
peripheral mode where the otg phy aborts halfway through setup. It also
fails to account for a failure to register the extcon notifier. Fix this
by using our own variable and skipping otg sync in case of failure.
Fixes: 8dc60f8da2 ("phy: rockchip-inno-usb2: Sync initial otg state")
Reported-by: Markus Reichl <m.reichl@fivetechno.de>
Reported-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220902184543.1234835-1-pgwipeout@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
RK3568 supports PCIe v3 using not Combphy like PCIe v2 on rk3566.
It use a dedicated PCIe-phy. Add support for this.
Initial support by Shawn Lin, modifications by Peter Geis and Frank
Wunderlich.
Add data-lanes property for splitting pcie-lanes across controllers.
The data-lanes is an array where x=0 means lane is disabled and x > 0
means controller x is assigned to phy lane.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Suggested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20220825193836.54262-4-linux@fw-web.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This adds support for variant found in Rockchip RK356x SoCs. Note that
only the basic operating mode is supported, in which all four CSI lines
are controlled by the Rockchip ISP.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20220720091527.1270365-3-michael.riesch@wolfvision.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When the OTG port is fixed to host mode, the driver does not request its
IRQs, nor does it enable those IRQs in hardware. Similarly, the driver
should ignore the OTG port IRQs when handling the shared interrupt.
Otherwise, it would update the extcon based on an ID pin which may be in
an undefined state, or try to queue a uninitialized work item.
Fixes: 6a98df08cc ("phy: rockchip-inno-usb2: Fix muxed interrupt support")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20220708061434.38115-1-samuel@sholland.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The initial otg state for the phy defaults to device mode. The actual
state isn't detected until an ID IRQ fires. Fix this by syncing the ID
state during initialization.
Fixes: 51a9b2c03d ("phy: rockchip-inno-usb2: Handle ID IRQ")
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220622003140.30365-1-pgwipeout@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If a phy supply is designated but isn't available at probe time, an
EPROBE_DEFER is returned. Use dev_err_probe to prevent this from
incorrectly printing during boot.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20220625212711.558495-1-pgwipeout@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This supports detecting host mode for the OTG port without an extcon.
The rv1108 properties are not updated due to lack of documentation.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20220414032258.40984-7-samuel@sholland.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some SoCs have a bvalid falling interrupt, in addition to bvalid rising.
This interrupt can detect OTG cable plugout immediately, so it can avoid
the delay until the next scheduled work.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20220414032258.40984-6-samuel@sholland.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The "bvalid" and "id" interrupts can trigger on either the rising edge
or the falling edge, so each interrupt has two enable bits and two
status bits. This change allows using a single property for both bits,
checking whether either bit is set.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20220414032258.40984-5-samuel@sholland.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Clearing the IRQ is atomic, so there is no need to hold the mutex.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20220414032258.40984-4-samuel@sholland.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The bvalid interrupt handler already checks bvalid status. The muxed IRQ
handler just needs to call the other handler (plus any other handlers
that will be added).
Signed-off-by: Samuel Holland <samuel@sholland.org>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20220414032258.40984-3-samuel@sholland.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This commit fixes two issues with the muxed interrupt handler. First,
the OTG port has the "bvalid" interrupt enabled, not "linestate". Since
only the linestate interrupt was handled, and not the bvalid interrupt,
plugging in a cable to the OTG port caused an interrupt storm.
Second, the return values from the individual port IRQ handlers need to
be OR-ed together. Otherwise, the lack of an interrupt from the last
port would cause the handler to erroneously return IRQ_NONE.
Fixes: ed2b5a8e6b ("phy: phy-rockchip-inno-usb2: support muxed interrupts")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20220414032258.40984-2-samuel@sholland.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch implements a combo phy driver for Rockchip SoCs
with NaNeng IP block. This phy can be used as pcie-phy, usb3-phy,
sata-phy or sgmii-phy.
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20220208091326.12495-4-yifeng.zhao@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The D-PHY specification (v1.2) explicitly mentions that the T-CLK-PRE
parameter's unit is Unit Interval(UI) and the minimum value is 8. Also,
kernel doc of the 'clk_pre' member of struct phy_configure_opts_mipi_dphy
mentions that it should be in UI. However, the dphy core driver wrongly
sets 'clk_pre' to 8000, which seems to hint that it's in picoseconds.
So, let's fix the dphy core driver to correctly reflect the T-CLK-PRE
parameter's minimum value according to the D-PHY specification.
I'm assuming that all impacted custom drivers shall program values in
TxByteClkHS cycles into hardware for the T-CLK-PRE parameter. The D-PHY
specification mentions that the frequency of TxByteClkHS is exactly 1/8
the High-Speed(HS) bit rate(each HS bit consumes one UI). So, relevant
custom driver code is changed to program those values as
DIV_ROUND_UP(cfg->clk_pre, BITS_PER_BYTE), then.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: 2ed869990e ("phy: Add MIPI D-PHY configuration options")
Tested-by: Liu Ying <victor.liu@nxp.com> # RM67191 DSI panel on i.MX8mq EVK
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Guido Günther <agx@sigxcpu.org> # Librem 5 (imx8mq) with it's rather picky panel
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20220124024007.1465018-1-victor.liu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The rk3568 usb2phy is a standalone device with a single muxed interrupt.
Add support for the registers to the usb2phy driver.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20211215210252.120923-7-pgwipeout@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The rk3568 usb2phy has a single muxed interrupt that handles all
interrupts.
Allow the driver to plug in only a single interrupt as necessary.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20211215210252.120923-6-pgwipeout@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
New Rockchip devices have the usb2 phy devices as standalone nodes
instead of children of the grf node.
Allow the driver to find the grf node from a phandle.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20211215210252.120923-5-pgwipeout@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
New Rockchip devices have the usb phy nodes as standalone devices.
These nodes have register nodes with #address_cells = 2, but only use 32
bit addresses.
Adjust the driver to check if the returned address is "0", and adjust
the index in that case.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20211215210252.120923-4-pgwipeout@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Variable delay is being assigned to zero and the code falls through to
the next case in a switch statement that returns out of the function.
The variable is never read in this scenario and so the assignment is
redundant and can be removed.
Cleans up scan-build static analysis warning:
drivers/phy/rockchip/phy-rockchip-inno-usb2.c:753:3: warning: Value
stored to 'delay' is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20211211180054.525368-1-colin.i.king@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The helper function devm_add_action_or_reset() will internally
call devm_add_action(), and gif devm_add_action() fails then it will
execute the action mentioned and return the error code. So
use devm_add_action_or_reset() instead of devm_add_action()
to simplify the error handling, reduce the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210922130024.745-1-caihuoqing@baidu.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For_each_available_child_of_node should have of_node_put()
before break around line 1184. The other jumps out of the
loop do contain the put.
Generated by: scripts/coccinelle/iterators/for_each_child.cocci
CC: Sumera Priyadarsini <sylphrenadin@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@inria.fr>
Link: https://lore.kernel.org/r/alpine.DEB.2.22.394.2106231617540.99238@hadrien
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The CSI dphy found for example on the rk3326/px30 and rk3368 is based
on an IP design from Innosilicon. Add a driver for it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20210610212935.3520341-3-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The pointer cfg is being initialized with a value that is never read and
it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210609113901.185230-1-colin.king@canonical.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The RK3308 SoC uses a slightly different USB phy than other Rockchip
parts.
This commit adds support for that phy.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20210514150044.2099298-3-t.schramm@manjaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to
walk all map elements in a more robust and easier to verify
fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF
on s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices
which don't need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability
on next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is
slow in reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take
place correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP
packets before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used
to define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
-independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and
bnxt support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP
which define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay
for packets sampled from switch HW (and corresponding egress
and policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP
forwarding, bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface
to distribute MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x -
11-port Ethernet switch with 8x 1-Gigabit Ethernet
and 3x 10-Gigabit interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365
and BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack,
matching on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode
changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vcbA
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
We have currently three users of the PSEC_PER_SEC each of them defining it
individually. Instead, move it to time64.h to be available for everyone.
There is a new user coming with the same constant in use. It will also
make its life easier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix OF node leaks by calling of_node_put in
for_each_available_child_of_node when the cycle returns.
Generated by: scripts/coccinelle/iterators/for_each_child.cocci
Signed-off-by: Junlin Yang <yangjunlin@yulong.com>
Link: https://lore.kernel.org/r/20210216084847.1544-1-angkery@163.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Update the implementation add "rockchip," vendor prefix for the
optional dts properties. Prefix referred from vendor-prefixes.yaml.
Follow up with
commit 8b5c2b45b8 ("phy: rockchip: set pulldown for strobe line in dts")
commit a8cef92827 ("phy: rockchip-emmc: output tap delay dt property")
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Link: https://lore.kernel.org/r/20201215014409.905-3-chris.ruehl@gtsys.com.hk
Signed-off-by: Vinod Koul <vkoul@kernel.org>
rockchip_emmc_phy_init() return variable is not set with the error value
if clk_get() failed. 'emmcclk' is optional, thus use clk_get_optional()
and if the return value != NULL make error processing and set the
return code accordingly.
Fixes: 52c0624a10 phy: rockchip-emmc: Set phyctrl_frqsel based on card clock
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201210080454.17379-1-chris.ruehl@gtsys.com.hk
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Update the rockchip-emmc phy to set the otapdlysec register with
a dt property. This was mentioned from Brian Norris when he sent
the path to set the default value in the driver.
This patch add a dt property 'output-tapdelay-select' u32 and allow
to set the 0x0-0xf. If not set in dts, the old default 0x4 applies.
Tested with our customized rk3399 to tune the eMMC.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Link: https://lore.kernel.org/r/20201202082507.3536-2-chris.ruehl@gtsys.com.hk
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch add support to set the internal pulldown via dt property
and allow simplify the board design for the trace from emmc-phy to
the eMMC chipset.
Default to not set the pull-down.
This patch was inspired from the 4.4 tree of the
Rockchip SDK, where it is enabled unconditional.
The patch had been tested with our rk3399 customized board.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Link: https://lore.kernel.org/r/20201129054416.3980-2-chris.ruehl@gtsys.com.hk
Signed-off-by: Vinod Koul <vkoul@kernel.org>
devm_ioremap_resource() will be not built in lib/devres.c if
CONFIG_HAS_IOMEM is not set, and then there exists a build
error about undefined reference to "devm_ioremap_resource"
in the file phy-rockchip-inno-hdmi.c under COMPILE_TEST and
CONFIG_PHY_ROCKCHIP_INNO_HDMI, make PHY_ROCKCHIP_INNO_HDMI
depend on HAS_IOMEM to fix it.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/1606216287-14648-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- Core:
- New PHY attribute for max_link_rate
- New phy drivers:
- Rockchip dphy driver moved from staging
- Socionext UniPhier AHCI PHY driver
- Intel LGM SoC USB phy
- Intel Keem Bay eMMC PHY driver
- Updates:
- Support for imx8mp usb phy
- Support for DP Phy and USB3+DP combo phy in QMP driver
- Support for Qualcomm sc7180 DP phy
- Support for cadence torrent PCIe and USB single linke and multilink
configurations along with USB, SGMII/QSGMII configurations
-----BEGIN PGP SIGNATURE-----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=U0WQ
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into usb-next
Vinod writes:
phy for 5.9
- Core:
- New PHY attribute for max_link_rate
- New phy drivers:
- Rockchip dphy driver moved from staging
- Socionext UniPhier AHCI PHY driver
- Intel LGM SoC USB phy
- Intel Keem Bay eMMC PHY driver
- Updates:
- Support for imx8mp usb phy
- Support for DP Phy and USB3+DP combo phy in QMP driver
- Support for Qualcomm sc7180 DP phy
- Support for cadence torrent PCIe and USB single linke and multilink
configurations along with USB, SGMII/QSGMII configurations
* tag 'phy-for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (72 commits)
phy: qcom-qmp: initialize the pointer to NULL
phy: qcom-qmp: Add support for sc7180 DP phy
phy: qcom-qmp: Add support for DP in USB3+DP combo phy
phy: qcom-qmp: Use devm_platform_ioremap_resource() to simplify
phy: qcom-qmp: Get dp_com I/O resource by index
phy: qcom-qmp: Move 'serdes' and 'cfg' into 'struct qcom_phy'
phy: qcom-qmp: Remove 'initialized' in favor of 'init_count'
phy: qcom-qmp: Move phy mode into struct qmp_phy
dt-bindings: phy: qcom,qmp-usb3-dp: Add DP phy information
dt-bindings: phy: ti,phy-j721e-wiz: fix bindings for torrent phy
dt-bindings: phy: cdns,torrent-phy: add reset-names
phy: rockchip-dphy-rx0: Include linux/delay.h
phy: fix USB_LGM_PHY warning & build errors
phy: cadence-torrent: Add USB + SGMII/QSGMII multilink configuration
phy: cadence-torrent: Add PCIe + USB multilink configuration
phy: cadence-torrent: Add single link USB register sequences
phy: cadence-torrent: Add single link SGMII/QSGMII register sequences
phy: cadence-torrent: Configure PHY_PLL_CFG as part of link_cmn_vals
phy: cadence-torrent: Add PHY link configuration sequences for single link
phy: cadence-torrent: Add clk changes for multilink configuration
...
We get warning with W=1 build:
drivers/phy/rockchip/phy-rockchip-typec.c:360: warning: cannot
understand function prototype: 'struct rockchip_usb3phy_port_cfg '
The 'struct rockchip_usb3phy_port_cfg ' is commented properly but uses
wrong format, so fix that up
Link: https://lore.kernel.org/r/20200708132809.265967-4-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Fixes: b7535a3bc0 ("phy/rockchip: Add support for Innosilicon MIPI/LVDS/TTL PHY")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/1590412138-13903-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
phy-rockchip-inno-usb2 logs the message
"phy-ff2c0000.syscon:usb2-phy@100.2: charger = INVALID_CHARGER"
constantly with a frequency of about 1 Hz and a verbosity level
of INFO. As this is clearly annoying, this patch decreases
the log level to DEBUG.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Jiapeng Chong