Add mutex support for platform IO operations. e.g. can be used
for platform DAPM widget IO ops.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Chip designers frequently include things like the enable and disable
controls for algorithms in the register blocks which also hold the
coefficients. Since it's desirable to split out the enable/disable
control from userspace the plain SND_SOC_BYTES() isn't optimal for
these devices.
Add a SND_SOC_BYTES_MASK() which allows a bitmask from the first word
of the block to be excluded from the control. This supports the needs
of devices I've looked at and lets us have a reasonably simple API.
Further controls can be added in future if that's needed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Allow devices to export blocks of registers to the application layer,
intended for use for reading and writing coefficient data which can't
usefully be worked with by the kernel at runtime (for example, due to
requiring complex and expensive calculations or being the results of
callibration procedures). Currently drivers are using platform data to
provide configurations for coefficient blocks which isn't at all
convenient for runtime management or configuration development.
Currently only devices using regmap are supported, an error will be
generated for any attempt to work with a byte control on a non-regmap
device. There's no fundamental block to other devices so support could
be added if required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Neater and avoids warnings when used in other places where const strings
are desired.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Allow platform widgets to be visible in debugfs like codec widgets.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is usually not a use case dependant flag anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Currently ASoC can only add kcontrols using codec and platform component device
handles. It's also desirable to add kcontrols for DAIs (i.e. McBSP) and for
SoC card machine drivers too. This allows the kcontrol to have a direct handle to
the parent ASoC component DAI/SoC Card/Platform/Codec device and hence easily
get it's private data.
This change makes snd_soc_add_controls() static and wraps it in the folowing
calls (card and dai are new) :-
snd_soc_add_card_controls()
snd_soc_add_codec_controls()
snd_soc_add_dai_controls()
snd_soc_add_platform_controls()
This patch also does a lot of small mechanical changes in individual codec drivers
to replace snd_soc_add_controls() with snd_soc_add_codec_controls().
It also updates the McBSP DAI driver to use snd_soc_add_dai_controls().
Finally, it updates the existing machine drivers that register controls to either :-
1) Use snd_soc_add_card_controls() where no direct codec control is required.
2) Use snd_soc_add_codec_controls() where there is direct codec control.
In the case of 1) above we also update the machine drivers to get the correct
component data pointers from the kcontrol (rather than getting the machine pointer
via the codec pointer).
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a driver is using regmap directly ensure that we're coherent with
non-ASoC register updates by using the regmap API directly to do our
read/modify/write cycles. This will bypass the ASoC cache but drivers
using regmap directly should not be using the ASoC cache.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Most devices accept data in formats that don't correspond directly to
their internal format. ALSA allows us to set a msbits constraint which
tells userspace about this in case it finds it useful (for example, in
order to avoid wasting effort dithering bits that will be ignored when
raising the sample size of data) so provide a mechanism for drivers to
specify the number of bits that are actually significant on a DAI and
add the appropriate constraints along with all the others.
This is done slightly awkwardly as the constraint is specified per sample
size - we loop over every possible sample size, including ones that the
device doesn't support and including ones that have fewer bits than are
actually used, but this is harmless as the upper layers do the right thing
in these cases.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The device model needs a release() function so it can free devices when
they become dereferenced. Do that for rtds.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that everything is seeing the same declaration by moving it to
a header file rather than putting the declaration in soc-core.c
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
DAI link endpoints and platform (DMA) devices are currently specified
by name. When instantiating sound cards from device tree, it may be more
convenient to refer to these devices by phandle in the device tree, and
for code to describe DAI links using the "struct device_node *"
("of_node") those phandles map to.
This change adds new fields to snd_soc_dai_link which can "name" devices
using of_node, enhances soc_bind_dai_link() to allow binding based on
of_node, and enhances snd_soc_register_card() to ensure that illegal
combinations of name and of_node are not used.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implement snd_soc_of_parse_audio_routing(), a utility function that can
parses a simple DAPM route table from device tree.The machine driver
specifies the DT property to use, since this is binding-specific.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implement snd_soc_of_parse_card_name(), a utility function that sets a
card's name from device tree. The machine driver specifies the DT
property to use, since this is binding-specific.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The existence of this parameter is purely historical. None of the CODEC drivers
uses it and we always pass in the same value anyway, so it should be safe to
remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A card is fully routed if the DAPM route table describes all connections on
the board.
When a card is fully routed, some operations can be automated by the ASoC
core. The first, and currently only, such operation is described below, and
implemented by this patch.
Codecs often have a large number of external pins, and not all of these pins
will be connected on all board designs. Some machine drivers therefore call
snd_soc_dapm_nc_pin() for all the unused pins, in order to tell the ASoC core
never to activate them.
However, when a card is fully routed, the information needed to derive the
set of unused pins is present in card->dapm_routes. In this case, have
the ASoC core automatically call snd_soc_dapm_nc_pin() for each unused
codec pin.
This has been tested with soc/tegra/tegra_wm8903.c and soc/tegra/trimslice.c.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are no current users and new drivers ought to be using the regmap
API and its cache implementation directly so just delete the ASoC copy.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
My usual technique for finding definitions is to search for "name {"
which breaks with the extra space.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With this flag, each dai_link in machine driver can choose
to ignore pmdown_time during DAPM shut down sequence.
If the ignore_pmdown_time is set, the DAPM for corresponding DAI
will be executed immediately.
Signed-off-by: Ramesh Babu K V <ramesh.babu@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With this flag codec drivers can indicate that it is desired
to ignore the pmdown_time for DAPM shutdown sequence when
playback stream is stopped.
The DAPM sequence will be executed without delay in this case.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
By accident few places still uses the _2r calls from
the core.
This is a quick fix, the drivers using the old callbacks
going to be changed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We do not have users for snd_soc_put_volsw_2r anymore.
It can be removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Handle the put_volsw/put_volsw_2r in one function.
To avoid build breakage in twl6040 keep the
snd_soc_put_volsw_2r as define, and map it snd_soc_put_volsw.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Handle the get_volsw/get_volsw_2r in one function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Handle the info_volsw/info_volsw_2r in one function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
SOC_SINGLE/DOUBLE_VALUE is used for mixer controls, where the
bits are within one register.
Assign .rreg to be the same as .reg for these types.
With this change we can tell if the mixer in question:
is mono:
mc->reg == mc->rreg && mc->shift == mc->rshift
is stereo, within single register:
mc->reg == mc->rreg && mc->shift != mc->rshift
is stereo, in two registers:
mc->reg != mc->rreg
The patch provide a small inline function to query, if the mixer
is stereo, or mono.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to reduce the number of DAPM power checks we run keep a list of
widgets which have been changed since the last DAPM run and iterate over
that rather than the full widget list. Whenever we change the power state
for a widget we add all the source and sink widgets it has to the dirty
list, ensuring that all widgets in the path are checked.
This covers more widgets than we need to as some of the neighbour widgets
won't be connected but it's simpler as a first step. On one system I tried
this gave:
Power Path Neighbour
Before: 207 1939 2461
After: 114 1066 1327
which seems useful.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With the new macro we can remove duplicated code
for the SOC_DOUBLE_R type of controls.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With the new macro we can remove duplicated code
for the SOC_DOUBLE type of controls.
We can also remap the SOC_SINGLE_VALUE macro to
SOC_DOUBLE_VALUE
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For almost all machines the DAI format is a constant, always set to the
same thing. This means that not only should we normally set it on init
rather than in hw_params() (where it has been for historical reasons) we
should also allow users to configure this by setting a variable in the
dai_link structure. The combination of these two will make many machine
drivers even more data driven.
Implement a new dai_fmt field in the dai_link doing just that. Since 0 is
a valid value for many format flags and we need to be able to tell if the
field is actually set also add one to all the values used to configure
formats.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The orginal code does not cover the case that one DAI such as codec
may be shared between other two DAIs(CPU).
When do symmetry checking, altough the codec DAI requires symmetry,
the two CPU DAIs may still be configured to run on different rates.
We change to check each DAI's state separately instead of only checking
the dai link to prevent this issue.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
One of the longest standing areas for improvement in ASoC has been the
DAPM algorithm - it repeats the same checks many times whenever it is run
and makes no effort to limit the areas of the graph it checks meaning we
do an awful lot of walks over the full graph. This has never mattered too
much as the size of the graph has generally been small in relation to the
size of the devices supported and the speed of CPUs but it is annoying.
In preparation for work on improving this insert a trace point after the
graph walk has been done. This gives us specific timing information for
the walk, and in order to give quantifiable (non-benchmark) numbers also
count every time we check a link or check the power for a widget and report
those numbers. Substantial changes in the algorithm may require tweaks to
the stats but they should be useful for simpler things.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Similarly to PLLs/FLLs some modern CODECs provide selectable system clock
sources. When the clock is the clock for a DAI we do not usually need to
identify which clock is being configured so can use clk_id for the source
clock but with CODEC wide system clocks we will need to specify both the
clock being configured and the source.
Add a source argument to the CODEC driver set_sysclk() operation to
reflect this. As this operation is not as widely used as the DAI
set_sysclk() operation the change is not very invasive. We probably
ought to go and make the same alternation for DAIs at some point.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Devices that need this exist; obviously the newer regmap defaults
mechanism will deal with this more happily.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If devices can unconditionally support idle_bias_off let them flag it in
their driver structure.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Allow drivers to set up their own regmap API structures. This is mainly
useful with MFDs where the core driver will have set up regmap at the
minute, though it may make sense to push the existing regmap setup out
of the core into the drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Remove all the ASoC specific physical I/O code and replace it with calls
into the regmap API. The bulk write code can only be used safely if all
regmap calls are locked with the CODEC lock, we need to add bulk support
to the regmap API or replace the code with an open coded loop (though
currently it has no users...).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
In preparation for Dynamic PCM (AKA DSP) support.
This adds a callback function to be called at the completion of a DAPM stream
event.
This can be used by DSP components to perform calculations based on DAPM graphs
after completion of stream events.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow platform probe to register platform kcontrols and DAPM just like
the CODEC probe().
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow platform driver widgets to perform any IO required for DAPM.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preparation for Dynamic PCM (AKA DSP) support.
Allow platform drivers to register kcontrols.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preparation for ASoC Dynamic PCM (AKA DSP) support.
Allow platform driver to perform IO. Intended for platform DAPM.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will be removed in -next so let's drop it from mainline as soon as
we can in order to minimise surprises.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preparation for the new ASoC Dynamic PCM support (AKA DSP support).
The new ASoC Dynamic PCM core allows DAIs to be dynamically re-routed
at runtime between the PCM device end (or Frontend - FE) and the physical DAI
(Backend - BE) using regular kcontrols (just like a hardware CODEC routes
audio in the analog domain). The Dynamic PCM core therefore must be
able to call PCM operations for both the Frontend and Backend(s) DAIs at
the same time.
Currently we have a global pcm_mutex that is used to serialise
the ASoC PCM operations. This patch removes the global mutex
and adds a mutex per RTD allowing the PCM operations to be reentrant and
allow control of more than one DAI at at time. e.g. a frontend PCM hw_params()
could configure multiple backend DAI hw_params() with similar or different
hw parameters at the same time.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some ASoC components depend on other ASoC components to provide clocks and
power resources in order to probe() and vice versa for remove().
Allow components to be ordered so that components can be probed() and removed()
in sequences that conform to their dependencies.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently pcm_new() passes in 3 arguments :- card, pcm and DAI.
Refactor this to only pass in 1 argument (i.e. the rtd) since struct rtd contains
card, pcm and DAI along with other members too that are useful too.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The card callback will get called for each DAPM context in the card so it
can be useful for it to know which device is currently undergoing a
transition.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Liam Girdwood