Adapt qeth l3 to:
commit c2e21293c0
(ipv6: convert addrconf list to hlist)
converted lst_next member of inet6_ifaddr struct to a hlist.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We never actually use iph again so this assignment can be removed.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
add routines for 8, 16 and 32-bit access like in
drivers/i2c/busses/i2c-pca-platform.c
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
extend the AND mask, so that IRQF_SHARED flag remains
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is patch to manipulate packet node allocation and implicitly
how packets are DMA'd etc.
The flag NODE_ALLOC enables the function and numa_node_id();
when enabled it can also be explicitly controlled via a new
node parameter
Tested this with 10 Intel 82599 ports w. TYAN S7025 E5520 CPU's.
Was able to TX/DMA ~80 Gbit/s to Ethernet wires.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use RCU to avoid RTNL use in dev_getfirstbyhwtype()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point to align or pad mibs to cache lines, they are per cpu
allocated with a 8 bytes alignment anyway.
This wastes space for no gain. This patch removes __SNMP_MIB_ALIGN__
Since SNMP mibs contain "unsigned long" fields only, we can relax the
allocation alignment from "unsigned long long" to "unsigned long"
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently force a synchronize_net() in netdev_set_master()
This seems necessary only when a slave had a master and we dismantle it.
In the other case ("ifenslave bond0 ethO"), we dont need this long
delay.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its currently hard to diagnose when ACK frames are dropped because an
application set TCP_DEFER_ACCEPT on its listening socket.
See http://bugzilla.kernel.org/show_bug.cgi?id=15507
This patch adds a SNMP value, named TCPDeferAcceptDrop
netstat -s | grep TCPDeferAcceptDrop
TCPDeferAcceptDrop: 0
This counter is incremented every time we drop a pure ACK frame received
by a socket in SYN_RECV state because its SYNACK retrans count is lower
than defer_accept value.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the type change, addresses in unicast and multicast lists wouldn't make
sense, not to mention possible different lenghts. So flush both lists here.
Note "dev_addr_discard" will be very soon replaced by "dev_mc_flush" (once
mc_list conversion will be done).
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ignore the new NETDEV_PRE_TYPE_CHANGE event in rtnetlink_event() since
there have been no changes userspace needs to be notified of.
Also add a comment to the netdev notifier event definitions to remind
people to update the exclusion list when adding new event types.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
hlist_for_each_entry(p...) will not necessarily initialize 'p'
to anything if the hlist is empty. GCC notices this and emits
a warning.
Just return true explicitly when we hit a match, and return
false is we fall out of the loop without one.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reduces timer events while keeping accuracy by rounding
our timer and/or batching several address validations in addrconf_verify().
addrconf_verify() is called at earliest timeout among interface addresses'
timeouts, but at maximum ADDR_CHECK_FREQUENCY (120 secs).
In most cases, all of timeouts of interface addresses are long enough
(e.g. several hours or days vs 2 minutes), this timer is usually called
every ADDR_CHECK_FREQUENCY, and it is okay to be lazy.
(Note this timer could be eliminated if all code paths which modifies
variables related to timeouts call us manually, but it is another story.)
However, in other least but important cases, we try keeping accuracy.
When the real interface address timeout is coming, and the timeout
is just before the rounded timeout, we accept some error.
When a timeout has been reached, we also try batching other several
events in very near future.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable regen_advance is only used in the privacy case.
Move it to simplify code and eliminate ifdef's
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor stuff, reformat comments and add whitespace for clarity
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to list macro's for the list of addresses per interface
in IPv6.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing hash function has a couple of issues:
* it is hardwired to 16 for IN6_ADDR_HSIZE
* limited to 256 and callers using int
* use jhash2 rather than some old BSD algorithm
No need for random seed since this is local only (based on assigned
addresses) table.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert from reader/writer lock to RCU and spinlock for addrconf
hash list.
Adds an additional helper macro for hlist_for_each_entry_continue_rcu
to handle the continue case.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using hash list macros, simplifies code and helps later RCU.
This patch includes some initialization that is not strictly necessary,
since an empty hlist node/list is all zero; and list is in BSS
and node is allocated with kzalloc.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use list macros instead of open coded linked list.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug that allows to lose events when reliable
event delivery mode is used, ie. if NETLINK_BROADCAST_SEND_ERROR
and NETLINK_RECV_NO_ENOBUFS socket options are set.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ENOBUFS errors are reported to the socket via
netlink_set_err() even if NETLINK_RECV_NO_ENOBUFS is set. However,
that should not happen. This fixes this problem and it changes the
prototype of netlink_set_err() to return the number of sockets that
have set the NETLINK_RECV_NO_ENOBUFS socket option. This return
value is used in the next patch in these bugfix series.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under NET_DMA, data transfer can grind to a halt when userland issues a
large read on a socket with a high RCVLOWAT (i.e., 512 KB for both).
This appears to be because the NET_DMA design queues up lots of memcpy
operations, but doesn't issue or wait for them (and thus free the
associated skbs) until it is time for tcp_recvmesg() to return.
The socket hangs when its TCP window goes to zero before enough data is
available to satisfy the read.
Periodically issue asynchronous memcpy operations, and free skbs for ones
that have completed, to prevent sockets from going into zero-window mode.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a unaligned access in nla_get_be64() that was
introduced by myself in a17c859849.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A packet is marked as lost in case packets == 0, although nothing should be done.
This results in a too early retransmitted packet during recovery in some cases.
This small patch fixes this issue by returning immediately.
Signed-off-by: Lennart Schulte <lennart.schulte@nets.rwth-aachen.de>
Signed-off-by: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
mfc_parent of cache entries is used to index into the vif_table and is
initialised from mfcctl->mfcc_parent. This can take values of to 2^16-1,
while the vif_table has only MAXVIFS (32) entries. The same problem
affects ip6mr.
Refuse invalid values to fix a potential out-of-bounds access. Unlike
the other validity checks, this is checked in ipmr_mfc_add() instead of
the setsockopt handler since its unused in the delete path and might be
uninitialized.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to adjust the next rx descriptor after each packet,
so do it only once at the end of the routine.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up some text output formatting.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recovery from PF reset works better when you shorten up the delay
until the watchdog task executes.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The counters in the 82599 Virtual Function are not clear on read. They
accumulate to the maximum value and then roll over. They are also not
cleared when the VF executes a soft reset, so it is possible they are
non-zero when the driver loads and starts. This has all been accounted
for in the code that keeps the stats up to date but there is one case
that is not. When the PF driver is reset the counters in the VF are
all reset to zero. This adds an additional accounting overhead into
the VF driver when the PF is reset under its feet. This patch adds
additional counters that are used by the VF driver to accumulate and
save stats after a PF reset has been detected. Prior to this patch
displaying the stats in the VF after the PF has reset would show
bogus data.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per Simon Horman's feedback set IXGBE_RSC_CB(skb)->dma to zero
after unmapping HWRSC DMA address to avoid double freeing.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently netdev_features_change is called before fcoe tx queues
setup is done, so this patch moves calling of netdev_features_change
after tx queues setup is done in ixgbe_init_interrupt_scheme, so
that real_num_tx_queues is updated correctly on each fcoe enable
or disable.
This allows additional fcoe queues updated correctly in vlan driver
for their correct queue selection.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds RFC5082 checks for TTL on received ICMP packets.
It adds some security against spoofed ICMP packets
disrupting GTSM protected sessions.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the only path leading to ip6_dst_check makes an indirect call
through dst->ops, dst cannot be NULL in ip6_dst_check.
This patch removes this check in case it misleads people who
come across this code.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xfrm_dst keeps a reference to ipv4 rtable entries on each
cached bundle. The only way to renew xfrm_dst when the underlying
route has changed, is to implement dst_check for this. This is
what ipv6 side does too.
The problems started after 87c1e12b5e
("ipsec: Fix bogus bundle flowi") which fixed a bug causing xfrm_dst
to not get reused, until that all lookups always generated new
xfrm_dst with new route reference and path mtu worked. But after the
fix, the old routes started to get reused even after they were expired
causing pmtu to break (well it would occationally work if the rtable
gc had run recently and marked the route obsolete causing dst_check to
get called).
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the connectivity check and recovery routine into separated
functions based on the types
1. iwl_good_ack_health() - check for ack count
2. iwl_good_plcp_health() - check for plcp error
Based on the type of errors being detected, different recovery methods
will be used to bring the system back to normal operational state.
Because different NIC has different HW and uCode, the behavior is also
different; these functions thus now form part of the ops infrastructure,
so we can have more control on how to monitor and recover from error condition
case per device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Monitors the tx statistics to detect the drop in throughput.
When the throughput drops, the ratio of the actual_ack_count and the
expected_ack_count also drops. At the same time, the aggregated
ba_timeout (the number of ba timeout retries) also rises. If the
actual_ack_count/expected_ack_count ratio is 0 and the number of ba
timeout retries rises to BA_TIMEOUT_MAX, no tx packets can be delivered.
Reloading the uCode and bring the system back to normal operational
state.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Move the plcp error checking into stand alone function and pointed by ops
to accommodate devices not needing this recovery.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Monitors the internal TX queues periodically. When a queue is stuck
for some unknown conditions causing the throughput to drop and the
transfer is stop, the driver will force firmware reload and bring the
system back to normal operational state.
The iwlwifi devices behave differently in this regard so this feature is
made part of the ops infrastructure so we can have more control on how to
monitor and recover from tx queue stall case per device.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Align the driver names with official product names for 1000/5000/6000
series. This change mainly affects the debug messages show up in system
log. No functional changes.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The only caller of this is iwl_rs_rate_init
which is only called with a valid sta_id.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
mac80211 recently implemented two new callbacks that are used to request
station add/remove from the driver. The benefot from these new callbacks
are that they enable the driver to sleep while performing this work.
This is a big patch since a few things need to be coordinated in this move.
First we need to decouple station management from rate scaling, which
caused a lot of code to be moved and/or deleted. Next we needed to tie in
with mac80211's station management callback and let it direct our station
management as well as trigger the rate scaling initialization.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Currently the broadcast station is added after every RXON command. Change
this to only add the broadcast station when interface is added by mac80211.
With this we need some extra work to ensure broadcast station is always
present since station table is cleared when RXON without ASSOC bit set is
sent. To deal with this we re-add all driver known stations to uCode after
such an RXON command is sent.
We also do some cleanup and remove the various calls to clear the station
table. We now only clear the station table in two scenarios:
- only clear uCode portion of station table when RXON command without ASSOC
bit is sent
- clear uCode and driver portion when interface goes down or is removed.
We need to do this clearing when interface goes down to deal with the
device restart/reconfigure routines which do not remove the interface, but
do add the interface during reconfiguration.
Previously the keys were also cleared when station table in driver is
cleared, this is not done anymore since mac80211 will take care that keys
are set and cleared correctly.
There is a known issue with this change. Associating with different AP
without bringing interface down fails with a firmware error. This is
because of the lack of full station notification support and the later
patches in this series that complete the station notification support will
fix this.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
David S. Miller