When set MTU to the minimum value 68, there are increasing number
of error packets occur, which is caused by the overflowed value of
mss. This patch fix the bug.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If mtu for debug port is set more than 1500, it may cause that packets
are dropped by ppe. So maximum value for debug port should be 1500.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In chip V1, the maximum mtu value is 9600. But in chip V2, it is 9728.
And it is always configurates as 9600 before this patch.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If trying to get receive flow hash indirection table by ethtool, it needs
to call .get_rxnfc to get ring number first. So this patch implements the
.get_rxnfc of ethtool. And the data type of rss_indir_table is u32, it has
to be multiply by the width of data type when using memcpy.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both .get_rxfh and .set_rxfh are always return 0, it should return result
from hardware when getting or setting rss. And the rss function should
return the correct data type.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the user manual of HNS V2 describs, XGE_DFX_CTRL_CFG.xge_dfx_ctrl_cfg
should be configed as zero if we want xge statistic reg to be read only.
But HNS V1 gets the other meanings. It needs to be identified the process
and then config it rightly.
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending a pause frame out from GMACs, the packets' source MAC address
does not match the GMACs' MAC address. It causes by the condition before
the mac address setting routine for GMACs, the mac address cannot be set
into loacal mac table for service ports. It obviously the condition needs
to be deleted.
Signed-off-by: Sheng Li <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Debug ports receives lots of packets with dest mac addr does not match
local mac addr, because the filter is close, and it does not drop the
useless packets. This patch adds ON/OFF switch of filtering the packets
whose dest mac addr do not match the local addr in mac table. And the
switch is ON in initialization.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In chip V2, the default value of port id in tx BD is Zero. If it is not
configurated to the other value, all management packets will be sent out
from port0. So port_id in the tx BD needs to be updated when sending a
management packet.
In V2 chip, when sending mamagement packets, the driver should
config the port id to BD descs.
Signed-off-by: Sheng Li <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current upstreaming code fails to ping other IPv6 net device, because
the enet receives the multicast packets with the src mac addr which is the
same as its mac addr. These packets need to be dropped.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct in6_addr isn't used anymore in inet6_connection_sock.h, removing
the forward declaration.
Fixes: 1b33bc3e9e ("ipv6: remove obsolete inet6 functions")
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By returning -ENOIOCTLCMD, sock_do_ioctl() falls back to calling
dev_ioctl(), which provides support for NIC driver ioctls, which
includes ethtool support. This is similar to the way ioctls are handled
in udp.c or tcp.c.
This removes the requirement that ethtool for example be tied to the
support of a specific L3 protocol (ethtool uses an AF_INET socket
today).
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates: commit 793cf87de9 ("ethtool: Set cmd field in
ETHTOOL_GLINKSETTINGS response to wrong nwords")
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Add target_alloc_session() w/ callback helper for doing se_session
allocation + tag + se_node_acl lookup. (HCH + nab)
- Tree-wide fabric driver conversion to use target_alloc_session()
- Convert sbp-target to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Chris Boot + nab)
- Convert usb-gadget to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Andrzej Pietrasiewicz + nab)
- Convert xen-scsiback to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Juergen Gross + nab)
- Convert tcm_fc to use TARGET_SCF_ACK_KREF I/O + TMR krefs
- Convert ib_srpt to use percpu_ida tag pre-allocation
- Add DebugFS node for qla2xxx target sess list (Quinn)
- Rework iser-target connection termination (Jenny + Sagi)
- Convert iser-target to new CQ API (HCH)
- Add pass-through WRITE_SAME support for IBLOCK (Mike Christie)
- Introduce data_bitmap for asynchronous access of data area (Sheng
Yang + Andy)
- Fix target_release_cmd_kref shutdown comp leak (Himanshu Madhani)
Also, there is a separate PULL request coming for cxgb4 NIC driver
prerequisites for supporting hw iscsi segmentation offload (ISO), that
will be the base for a number of v4.7 developments involving
iscsi-target hw offloads"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (36 commits)
target: Fix target_release_cmd_kref shutdown comp leak
target: Avoid DataIN transfers for non-GOOD SAM status
target/user: Report capability of handling out-of-order completions to userspace
target/user: Fix size_t format-spec build warning
target/user: Don't free expired command when time out
target/user: Introduce data_bitmap, replace data_length/data_head/data_tail
target/user: Free data ring in unified function
target/user: Use iovec[] to describe continuous area
target: Remove enum transport_lunflags_table
target/iblock: pass WRITE_SAME to device if possible
iser-target: Kill the ->isert_cmd back pointer in struct iser_tx_desc
iser-target: Kill struct isert_rdma_wr
iser-target: Convert to new CQ API
iser-target: Split and properly type the login buffer
iser-target: Remove ISER_RECV_DATA_SEG_LEN
iser-target: Remove impossible condition from isert_wait_conn
iser-target: Remove redundant wait in release_conn
iser-target: Rework connection termination
iser-target: Separate flows for np listeners and connections cma events
iser-target: Add new state ISER_CONN_BOUND to isert_conn
...
TI DRA7xx host bridge driver
Revert "PCI: dra7xx: Mark driver as broken" (Sekhar Nori)
Miscellaneous
Restore inclusion of pci/hotplug Kconfig (Tero Roponen)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=M4Kl
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.6-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Here are two fixes for v4.6:
- You merged a fix for a TI DRA7xx reset issue from another source,
so Sekhar removed the "broken" tag from the driver, and
- I botched a Kconfig merge and broke hotplug configuration for
everybody, so Tero fixed that.
Summary:
TI DRA7xx host bridge driver:
Revert "PCI: dra7xx: Mark driver as broken" (Sekhar Nori)
Miscellaneous:
Restore inclusion of pci/hotplug Kconfig (Tero Roponen)"
* tag 'pci-v4.6-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI: dra7xx: Mark driver as broken"
PCI: Restore inclusion of pci/hotplug Kconfig
The previous pull request introduced a few WARN_ON() for Intel
HD-audio HDMI. Indeed it caught bugs, and now users get annoyed.
So this request came up: a collection of small fixes to paper over
the inconsistencies on (mostly) old Intel chipsets.
In addition, a trivial USB-audio quirk is included, too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ac9g
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The previous pull request introduced a few WARN_ON() for Intel
HD-audio HDMI. Indeed it caught bugs, and now users get annoyed. So
this request came up: a collection of small fixes to paper over the
inconsistencies on (mostly) old Intel chipsets.
In addition, a trivial USB-audio quirk is included, too"
* tag 'sound-fix-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix missing ELD update at unplugging
ALSA: usb-audio: add Microsoft HD-5001 to quirks
ALSA: hda - Workaround for unbalanced i915 power refcount by concurrent probe
ALSA: hda - Fix spurious kernel WARNING on Baytrail HDMI
ALSA: hda - Fix forgotten HDMI monitor_present update
ALSA: hda - Really restrict i915 notifier to HSW+
This time with:
* Updates for the Exynos IOMMU driver to make use of default
domains and to add support for the SYSMMU v5
* New Mediatek IOMMU driver
* Support for the ARMv7 short descriptor format in the
io-pgtable code
* Default domain support for the ARM SMMU
* Couple of other small fixes all over the place
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=uiAk
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- updates for the Exynos IOMMU driver to make use of default domains
and to add support for the SYSMMU v5
- new Mediatek IOMMU driver
- support for the ARMv7 short descriptor format in the io-pgtable code
- default domain support for the ARM SMMU
- couple of other small fixes all over the place
* tag 'iommu-updates-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (41 commits)
iommu/ipmmu-vmsa: Add r8a7795 DT binding
iommu/mediatek: Check for NULL instead of IS_ERR()
iommu/io-pgtable-armv7s: Fix kmem_cache_alloc() flags
iommu/mediatek: Fix handling of of_count_phandle_with_args result
iommu/dma: Fix NEED_SG_DMA_LENGTH dependency
iommu/mediatek: Mark PM functions as __maybe_unused
iommu/mediatek: Select ARM_DMA_USE_IOMMU
iommu/exynos: Use proper readl/writel register interface
iommu/exynos: Pointers are nto physical addresses
dts: mt8173: Add iommu/smi nodes for mt8173
iommu/mediatek: Add mt8173 IOMMU driver
memory: mediatek: Add SMI driver
dt-bindings: mediatek: Add smi dts binding
dt-bindings: iommu: Add binding for mediatek IOMMU
iommu/ipmmu-vmsa: Use ARCH_RENESAS
iommu/exynos: Support multiple attach_device calls
iommu/exynos: Add Maintainers entry for Exynos SYSMMU driver
iommu/exynos: Add support for v5 SYSMMU
iommu/exynos: Update device tree documentation
iommu/exynos: Add support for SYSMMU controller with bogus version reg
...
You could add any multiple of 2^32/PNFS_SCSI_RANGE_SIZE to nr_iomaps and
still pass this check. You'd probably still fail the following kcalloc,
but best to be paranoid since this is from-the-wire data.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Make sure the CQE phase (validity) is read before the rest of the
structure. The phase bit is the highest address and the CQE
read will happen on most platforms from lower to upper addresses
and will be done by multiple non-atomic loads. If the structure
is updated by PCI during the reads from the processor, the
processor may get a corrupted copy.
The addition of the new nvme_cqe_valid function that verifies
the validity bit also allows refactoring of the other CQE read
sequences.
Signed-off-by: Marta Rybczynska <marta.rybczynska@kalray.eu>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Build on 32-bit PPC fails with the following error:
int kvm_vfio_ops_init(void)
^
In file included from arch/powerpc/kvm/../../../virt/kvm/vfio.c:21:0:
arch/powerpc/kvm/../../../virt/kvm/vfio.h:8:90: note: previous definition of ‘kvm_vfio_ops_init’ was here
arch/powerpc/kvm/../../../virt/kvm/vfio.c:292:6: error: redefinition of ‘kvm_vfio_ops_exit’
void kvm_vfio_ops_exit(void)
^
In file included from arch/powerpc/kvm/../../../virt/kvm/vfio.c:21:0:
arch/powerpc/kvm/../../../virt/kvm/vfio.h:12:91: note: previous definition of ‘kvm_vfio_ops_exit’ was here
scripts/Makefile.build:258: recipe for target arch/powerpc/kvm/../../../virt/kvm/vfio.o failed
make[3]: *** [arch/powerpc/kvm/../../../virt/kvm/vfio.o] Error 1
Check whether CONFIG_KVM_VFIO is set before including vfio.o
in the build.
Reported-by: Pranith Kumar <bobby.prani@gmail.com>
Tested-by: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The async pagefault wake code can run from the idle task in exception
context, so everything here needs to be made non-preemptible.
Conversion to a simple wait queue and raw spinlock does the trick.
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The barrier also orders the write to mode from any reads
to the page tables done and so update the comment.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The barrier also orders the write to mode from any reads
to the page tables done and so update the comment.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
smp_load_acquire() is enough here and it's cheaper than smp_mb().
Adding a comment about reusing memory barrier of kvm_make_all_cpus_request()
here to keep order between modifications to the page tables and reading mode.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Update spte before increasing tlbs_dirty to make sure no tlb flush
in lost after spte is zapped. This pairs with the barrier in the
kvm_flush_remote_tlbs().
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is already a barrier inside of kvm_flush_remote_tlbs() which can
help to make sure everyone sees our modifications to the page tables and
see changes to vcpu->mode here. So remove the smp_mb in the
kvm_mmu_commit_zap_page() and update the comment.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
X86_FEATURE_PKU is referred to as "PKU" in the hardware documentation:
CPUID.7.0.ECX[3]:PKU. X86_FEATURE_OSPKE is software support for pkeys,
enumerated with CPUID.7.0.ECX[4]:OSPKE, and it reflects the setting of
CR4.PKE(bit 22).
This patch disables CPUID:PKU without ept, because pkeys is not yet
implemented for shadow paging.
Signed-off-by: Huaitong Han <huaitong.han@intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Protection keys define a new 4-bit protection key field (PKEY) in bits
62:59 of leaf entries of the page tables, the PKEY is an index to PKRU
register(16 domains), every domain has 2 bits(write disable bit, access
disable bit).
Static logic has been produced in update_pkru_bitmask, dynamic logic need
read pkey from page table entries, get pkru value, and deduce the correct
result.
[ Huaitong: Xiao helps to modify many sections. ]
Signed-off-by: Huaitong Han <huaitong.han@intel.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
PKEYS defines a new status bit in the PFEC. PFEC.PK (bit 5), if some
conditions is true, the fault is considered as a PKU violation.
pkru_mask indicates if we need to check PKRU.ADi and PKRU.WDi, and
does cache some conditions for permission_fault.
[ Huaitong: Xiao helps to modify many sections. ]
Signed-off-by: Huaitong Han <huaitong.han@intel.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently XSAVE state of host is not restored after VM-exit and PKRU
is managed by XSAVE so the PKRU from guest is still controlling the
memory access even if the CPU is running the code of host. This is
not safe as KVM needs to access the memory of userspace (e,g QEMU) to
do some emulation.
So we save/restore PKRU when guest/host switches.
Signed-off-by: Huaitong Han <huaitong.han@intel.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM will use it to switch pkru between guest and host.
CC: Ingo Molnar <mingo@redhat.com>
CC: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Huaitong Han <huaitong.han@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds pkeys support for xsave state.
Signed-off-by: Huaitong Han <huaitong.han@intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pkeys is disabled if CPU is in non-paging mode in hardware. However KVM
always uses paging mode to emulate guest non-paging, mode with TDP. To
emulate this behavior, pkeys needs to be manually disabled when guest
switches to non-paging mode.
Signed-off-by: Huaitong Han <huaitong.han@intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch removes magic number with enum cpuid_leafs.
Signed-off-by: Huaitong Han <huaitong.han@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will help in the implementation of PKRU, where the PK bit of the page
fault error code cannot be computed in advance (unlike I/D, R/W and U/S).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
'struct timeval' uses a 32 bit field for its 'seconds' value which
will overflow in year 2038 and beyond. This patch replaces the use
of timeval in nosy.c with timespec64 which doesn't suffer from y2038
issue. The code is correct as is - since it is only using the
microseconds portion of timeval. However, this patch does the
replacement as part of a larger effort to remove all instances of
'struct timeval' from the kernel (that would help identify cases
where the code is actually broken).
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Correctly document what is implemented for :ppp on Intel CPUs in recent
kernels.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1458575793-12091-2-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Revert 5c3b99d057 ("PCI: dra7xx: Mark driver as broken").
1c96bee4df ("ARM: DRA7: hwmod: Add custom reset handler for PCIeSS")
added support to de-assert PCIe reset, so DRA7x PCIe is not broken anymore.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Moving the initialization earlier is needed in 4.6 because
kvm_arch_init_vm is now using mmu_lock, causing lockdep to
complain:
[ 284.440294] INFO: trying to register non-static key.
[ 284.445259] the code is fine but needs lockdep annotation.
[ 284.450736] turning off the locking correctness validator.
...
[ 284.528318] [<ffffffff810aecc3>] lock_acquire+0xd3/0x240
[ 284.533733] [<ffffffffa0305aa0>] ? kvm_page_track_register_notifier+0x20/0x60 [kvm]
[ 284.541467] [<ffffffff81715581>] _raw_spin_lock+0x41/0x80
[ 284.546960] [<ffffffffa0305aa0>] ? kvm_page_track_register_notifier+0x20/0x60 [kvm]
[ 284.554707] [<ffffffffa0305aa0>] kvm_page_track_register_notifier+0x20/0x60 [kvm]
[ 284.562281] [<ffffffffa02ece70>] kvm_mmu_init_vm+0x20/0x30 [kvm]
[ 284.568381] [<ffffffffa02dbf7a>] kvm_arch_init_vm+0x1ea/0x200 [kvm]
[ 284.574740] [<ffffffffa02bff3f>] kvm_dev_ioctl+0xbf/0x4d0 [kvm]
However, it also helps fixing a preexisting problem, which is why this
patch is also good for stable kernels: kvm_create_vm was incrementing
current->mm->mm_count but not decrementing it at the out_err label (in
case kvm_init_mmu_notifier failed). The new initialization order makes
it possible to add the required mmdrop without adding a new error label.
Cc: stable@vger.kernel.org
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Upcoming in-kernel VFIO acceleration needs different handling in real
and virtual modes which makes it hard to support both modes in
the same handler.
This creates a copy of kvmppc_rm_h_stuff_tce and kvmppc_rm_h_put_tce
in addition to the existing kvmppc_rm_h_put_tce_indirect.
This also fixes linker breakage when only PR KVM was selected (leaving
HV KVM off): the kvmppc_h_put_tce/kvmppc_h_stuff_tce functions
would not compile at all and the linked would fail.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Old KVM guests invoke single-context invvpid without actually checking
whether it is supported. This was fixed by commit 518c8ae ("KVM: VMX:
Make sure single type invvpid is supported before issuing invvpid
instruction", 2010-08-01) and the patch after, but pre-2.6.36
kernels lack it including RHEL 6.
Reported-by: jmontleo@redhat.com
Tested-by: jmontleo@redhat.com
Cc: stable@vger.kernel.org
Fixes: 99b83ac893
Reviewed-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A guest executing an invalid invvpid instruction would hang
because the instruction pointer was not updated.
Reported-by: jmontleo@redhat.com
Tested-by: jmontleo@redhat.com
Cc: stable@vger.kernel.org
Fixes: 99b83ac893
Reviewed-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A guest executing an invalid invept instruction would hang
because the instruction pointer was not updated.
Cc: stable@vger.kernel.org
Fixes: bfd0a56b90
Reviewed-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If enabling the hsmci regulator on card detection, the board can reboot
on sd card insertion. Keeping the regulator always enabled fixes this
issue.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 8d545f32bd ("ARM: at91/dt: sama5d4 xplained: add regulators for v(q)mmc1 supplies")
Cc: stable@vger.kernel.org #4.3 and later
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
If enabling the hsmci regulator on card detection, the board can reboot
on sd card insertion. Keeping the regulator always enabled fixes this
issue.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 1b53e3416d ("ARM: at91/dt: sama5d3 xplained: add fixed regulator for vmmc0")
Cc: stable@vger.kernel.org #4.3 and later
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Second round of patches for v4.6-rc1, fixing a small handful of issue:
- disable preemption when calling smp_call_function_many
- Make kvm_ksym_ref work on VHE systems again after KASRL breakage
- Disable compiler instrumentation for hypervisor code that could make
KVM/arm64 blow up.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW8PwIAAoJEEtpOizt6ddyEFMH/RBhWA2M/+1Na6W75+283gqy
zqBnPQcQQJ5PmD2Pm9G/+3Q7B47xuKhiEJ8bOcwh7zgBtF5SeZmrdO3YMB5r8RuL
lj5O6q3nzEyTpy9Cl2TPK5EU+RRB8crpaQQ98o7w7mBZdsPB8SnzKsfizURxWMfy
oqHuazktRFPf3Aa3nbBaEv8BvR0HRHErokl8BLVWEkomwqBzoJHTCCfeT7sVdc3X
zfhLHG9q9BX5H97aJTzkVTxvPdCMei8Noko3BipaF8JLbsG5e3ssL0GlAkwwhXQn
c0qB/lIqSaJU8N307RYfpeeGBgqIIn6IO4TpfJMqQs8Rvr7NxmgcTOmz33+OHAE=
=whOa
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM Changes for v4.6-rc1
Second round of patches for v4.6-rc1, fixing a small handful of issue:
- disable preemption when calling smp_call_function_many
- Make kvm_ksym_ref work on VHE systems again after KASRL breakage
- Disable compiler instrumentation for hypervisor code that could make
KVM/arm64 blow up.
Daode Huang