Here are two tty serial driver fixes for 4.13-rc5. One is a revert of a
-rc1 patch that turned out to not be a good idea, and the other is a fix
for the pl011 serial driver.
Both have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWY+1vw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykreACeLI2spfagnOcnW264PGHxLMgj47EAn0JPSNIg
5FLEtVsgxMuc8kc4LkDb
=58g+
-----END PGP SIGNATURE-----
Merge tag 'tty-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are two tty serial driver fixes for 4.13-rc5. One is a revert of
a -rc1 patch that turned out to not be a good idea, and the other is a
fix for the pl011 serial driver.
Both have been in linux-next with no reported issues"
* tag 'tty-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: Delete dead code for CIR serial ports"
tty: pl011: fix initialization order of QDF2400 E44
Here are some Staging and IIO driver fixes for 4.13-rc5.
Nothing major, just a number of small fixes for reported issues. All of
these have been in linux-next for a while now with no reported issues.
Full details are in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWY+0+A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykwSgCgzvxKfEcAHXOxB90/bHl3yWh+Xe0AoNRX5xEX
gavfFbhZlrPqtlZGX1ZI
=NmcC
-----END PGP SIGNATURE-----
Merge tag 'staging-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/iio fixes from Greg KH:
"Here are some Staging and IIO driver fixes for 4.13-rc5.
Nothing major, just a number of small fixes for reported issues. All
of these have been in linux-next for a while now with no reported
issues. Full details are in the shortlog"
* tag 'staging-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: comedi_fops: do not call blocking ops when !TASK_RUNNING
iio: aspeed-adc: wait for initial sequence.
iio: accel: bmc150: Always restore device to normal mode after suspend-resume
staging:iio:resolver:ad2s1210 fix negative IIO_ANGL_VEL read
iio: adc: axp288: Fix the GPADC pin reading often wrongly returning 0
iio: adc: vf610_adc: Fix VALT selection value for REFSEL bits
iio: accel: st_accel: add SPI-3wire support
iio: adc: Revert "axp288: Drop bogus AXP288_ADC_TS_PIN_CTRL register modifications"
iio: adc: sun4i-gpadc-iio: fix unbalanced irq enable/disable
iio: pressure: st_pressure_core: disable multiread by default for LPS22HB
iio: light: tsl2563: use correct event code
Here are a number of small USB driver fixes and new device ids for
4.13-rc5. There is the usual gadget driver fixes, some new quirks for
"messy" hardware, and some new device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWY+2eA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynSGACgrMjsqOsgjgVEnc1IdjS2gHEZnfcAoMmyBGwo
cNOM+8gnysJLFUTwkppl
=+bPU
-----END PGP SIGNATURE-----
Merge tag 'usb-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes and new device ids for
4.13-rc5. There is the usual gadget driver fixes, some new quirks for
"messy" hardware, and some new device ids.
All have been in linux-next with no reported issues"
* tag 'usb-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: pl2303: add new ATEN device id
usb: quirks: Add no-lpm quirk for Moshi USB to Ethernet Adapter
USB: Check for dropped connection before switching to full speed
usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume
usb: renesas_usbhs: gadget: fix unused-but-set-variable warning
usb: renesas_usbhs: Fix UGCTRL2 value for R-Car Gen3
usb: phy: phy-msm-usb: Fix usage of devm_regulator_bulk_get()
usb: gadget: udc: renesas_usb3: Fix usb_gadget_giveback_request() calling
usb: dwc3: gadget: Correct ISOC DATA PIDs for short packets
USB: serial: option: add D-Link DWM-222 device ID
usb: musb: fix tx fifo flush handling again
usb: core: unlink urbs from the tail of the endpoint's urb_list
usb-storage: fix deadlock involving host lock and scsi_done
uas: Add US_FL_IGNORE_RESIDUE for Initio Corporation INIC-3069
USB: hcd: Mark secondary HCD as dead if the primary one died
USB: serial: cp210x: add support for Qivicon USB ZigBee dongle
An mtdblock regression occurred in -rc1 (all writes were broken!), in the
process of some block subsystem refactoring. Noticed and fixed last week, but
I'm a little slow on the uptake.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RDXe
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20170812' of git://git.infradead.org/linux-mtd
Pull another MTD fix from Brian Norris:
"An mtdblock regression occurred in -rc1 (all writes were broken!), in
the process of some block subsystem refactoring. Noticed and fixed
last week, but I'm a little slow on the uptake"
* tag 'for-linus-20170812' of git://git.infradead.org/linux-mtd:
mtd: blkdevs: Fix mtd block write failure
All the MTD block write requests are failing with
following error messages
mkfs.ext4 /dev/mtdblock0
print_req_error: I/O error, dev mtdblock0, sector 0
Buffer I/O error on dev mtdblock0, logical block 0,
lost async page write
The control is going to default case after block write request
because of missing return.
Fixes: commit 2a842acab1 ("block: introduce new block status code type")
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJZjs9BAAoJELDendYovxMvXXAH/j3pdoshQbflSUBsDAkybhv5
BVe7+bhtwnoawcjCpXq27SMY3qG/YWnATW28XjxBCoe3t7StNcJr5QGXTWMnTjwN
f/YA0aqtCoLp9JhovTi9WTTCf1/I9CKYFBdCaAmLkDeMudyifZkbXiDbDe0UZmAc
UJt0Jx8KrdMGkuRVp92049calluv+PDHO7gUpGpzoHDJ0IXc1cH9caHTbL+LhioY
o0qqQOz9FnJQIvqSGYRkjXudmGwHYCr61yXvWhwqa4PE3Tzss2ckGtzZPLI8s1QN
p5m01FbIMQKjLbwpQZaRWmGxSzY2vYxf/TShK8eIsBfRYxsR4d7cXULC2vIJGFI=
=jiAk
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.13b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Some fixes for Xen:
- a fix for a regression introduced in 4.13 for a Xen HVM-guest
configured with KASLR
- a fix for a possible deadlock in the xenbus driver when booting the
system
- a fix for lost interrupts in Xen guests"
* tag 'for-linus-4.13b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/events: Fix interrupt lost during irq_disable and irq_enable
xen: avoid deadlock in xenbus
xen: fix hvm guest with kaslr enabled
xen: split up xen_hvm_init_shared_info()
x86: provide an init_mem_mapping hypervisor hook
Stable fix:
- Fix leaking nfs4_ff_ds_version array
Other fixes:
- Improve TEST_STATEID OLD_STATEID handling to prevent recovery loop
- Require 64-bit sector_t for pNFS blocklayout to prevent 32-bit compile
errors
-----BEGIN PGP SIGNATURE-----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=1/Ms
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.13-5' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client fixes from Anna Schumaker:
"A few more NFS client bugfixes from me for rc5.
Dros has a stable fix for flexfiles to prevent leaking the
nfs4_ff_ds_version arrays when freeing a layout, Trond fixed a
potential recovery loop situation with the TEST_STATEID operation, and
Christoph fixed up the pNFS blocklayout Kconfig options to prevent
unsafe use with kernels that don't have large block device support.
Summary:
Stable fix:
- fix leaking nfs4_ff_ds_version array
Other fixes:
- improve TEST_STATEID OLD_STATEID handling to prevent recovery loop
- require 64-bit sector_t for pNFS blocklayout to prevent 32-bit
compile errors"
* tag 'nfs-for-4.13-5' of git://git.linux-nfs.org/projects/anna/linux-nfs:
pnfs/blocklayout: require 64-bit sector_t
NFSv4: Ignore NFS4ERR_OLD_STATEID in nfs41_check_open_stateid()
nfs/flexfiles: fix leak of nfs4_ff_ds_version arrays
Pull block fixes from Jens Axboe:
"A set of fixes that should go into this series. This contains:
- Fix from Bart for blk-mq requeue queue running, preventing a
continued loop of run/restart.
- Fix for a bio/blk-integrity issue, in two parts. One from
Christoph, fixing where verification happens, and one from Milan,
for a NULL profile.
- NVMe pull request, most of the changes being for nvme-fc, but also
a few trivial core/pci fixes"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme: fix directive command numd calculation
nvme: fix nvme reset command timeout handling
nvme-pci: fix CMB sysfs file removal in reset path
lpfc: support nvmet_fc defer_rcv callback
nvmet_fc: add defer_req callback for deferment of cmd buffer return
nvme: strip trailing 0-bytes in wwid_show
block: Make blk_mq_delay_kick_requeue_list() rerun the queue at a quiet time
bio-integrity: only verify integrity on the lowest stacked driver
bio-integrity: Fix regression if profile verify_fn is NULL
Pull fuse fixes from Miklos Szeredi:
"Fix a few bugs in fuse"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: set mapping error in writepage_locked when it fails
fuse: Dont call set_page_dirty_lock() for ITER_BVEC pages for async_dio
fuse: initialize the flock flag in fuse_file on allocation
The blocklayout code does not compile cleanly for a 32-bit sector_t,
and also has no reliable checks for devices sizes, which makes it
unsafe to use with a kernel that doesn't support large block devices.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5c83746a0c ("pnfs/blocklayout: in-kernel GETDEVICEINFO XDR parsing")
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
All fixes for code that went in this cycle.
- A revert of an optimisation to the syscall exit path, which could lead to an
oops on either older machines or machines with > 1T of memory.
- Disable some deep idle states if the firmware configuration for them fails.
- Re-enable HARD/SOFT lockup detectors in defconfigs after a Kconfig change.
- Six fairly small patches fixing bugs in our new watchdog code.
Thanks to:
Gautham R. Shenoy, Nicholas Piggin.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Vy1K
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.13-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"All fixes for code that went in this cycle.
- a revert of an optimisation to the syscall exit path, which could
lead to an oops on either older machines or machines with > 1TB of
memory
- disable some deep idle states if the firmware configuration for
them fails
- re-enable HARD/SOFT lockup detectors in defconfigs after a Kconfig
change
- six fairly small patches fixing bugs in our new watchdog code
Thanks to: Gautham R Shenoy, Nicholas Piggin"
* tag 'powerpc-4.13-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/watchdog: add locking around init/exit functions
powerpc/watchdog: Fix marking of stuck CPUs
powerpc/watchdog: Fix final-check recovered case
powerpc/watchdog: Moderate touch_nmi_watchdog overhead
powerpc/watchdog: Improve watchdog lock primitive
powerpc: NMI IPI improve lock primitive
powerpc/configs: Re-enable HARD/SOFT lockup detectors
powerpc/powernv/idle: Disable LOSE_FULL_CONTEXT states when stop-api fails
Revert "powerpc/64: Avoid restore_math call if possible in syscall exit"
Commit c54451a "iommu/arm-smmu: Fix the error path in arm_smmu_add_device"
removed fwspec assignment in legacy_binding path as redundant which is
wrong. It needs to be updated after fwspec initialisation in
arm_smmu_register_legacy_master() as it is dereferenced later. Without
this there is a NULL-pointer dereference panic during boot on some hosts.
Signed-off-by: Artem Savkov <asavkov@redhat.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Here is a device has xen-pirq-MSI interrupt. Dom0 might lost interrupt
during driver irq_disable/irq_enable. Here is the scenario,
1. irq_disable -> disable_dynirq -> mask_evtchn(irq channel)
2. dev interrupt raised by HW and Xen mark its evtchn as pending
3. irq_enable -> startup_pirq -> eoi_pirq ->
clear_evtchn(channel of irq) -> clear pending status
4. consume_one_event process the irq event without pending bit assert
which result in interrupt lost once
5. No HW interrupt raising anymore.
Now use enable_dynirq for enable_pirq of xen_pirq_chip to remove
eoi_pirq when irq_enable.
Signed-off-by: Liu Shuo <shuo.a.liu@intel.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
When starting the xenwatch thread a theoretical deadlock situation is
possible:
xs_init() contains:
task = kthread_run(xenwatch_thread, NULL, "xenwatch");
if (IS_ERR(task))
return PTR_ERR(task);
xenwatch_pid = task->pid;
And xenwatch_thread() does:
mutex_lock(&xenwatch_mutex);
...
event->handle->callback();
...
mutex_unlock(&xenwatch_mutex);
The callback could call unregister_xenbus_watch() which does:
...
if (current->pid != xenwatch_pid)
mutex_lock(&xenwatch_mutex);
...
In case a watch is firing before xenwatch_pid could be set and the
callback of that watch unregisters a watch, then a self-deadlock would
occur.
Avoid this by setting xenwatch_pid in xenwatch_thread().
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
A Xen HVM guest running with KASLR enabled will die rather soon today
because the shared info page mapping is using va() too early. This was
introduced by commit a5d5f328b0 ("xen:
allocate page for shared info page from low memory").
In order to fix this use early_memremap() to get a temporary virtual
address for shared info until va() can be used safely.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Instead of calling xen_hvm_init_shared_info() on boot and resume split
it up into a boot time function searching for the pfn to use and a
mapping function doing the hypervisor mapping call.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Provide a hook in hypervisor_x86 called after setting up initial
memory mapping.
This is needed e.g. by Xen HVM guests to map the hypervisor shared
info page.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
This ensures that we see errors on fsync when writeback fails.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
-----BEGIN PGP SIGNATURE-----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=rjAR
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-v4.13-rc5' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nothing too earth shattering here, it just seems like lots of little
things all over the place.
msm has probably the larger amount of changes, but they all seem fine,
otherwise, some rockchip, i915, etnaviv and exynos fixes, along with
one nouveau regression fix for some older GPUs"
* tag 'drm-fixes-for-v4.13-rc5' of git://people.freedesktop.org/~airlied/linux: (35 commits)
drm/nouveau/disp/nv04: avoid creation of output paths
drm: make DRM_STM default n
drm/exynos: forbid creating framebuffers from too small GEM buffers
drm/etnaviv: Fix off-by-one error in reloc checking
drm/i915: fix backlight invert for non-zero minimum brightness
drm/i915/shrinker: Wrap need_resched() inside preempt-disable
drm/i915/perf: fix flex eu registers programming
drm/i915: Fix out-of-bounds array access in bdw_load_gamma_lut
drm/i915/gvt: Change the max length of mmio_reg_rw from 4 to 8
drm/i915/gvt: Initialize MMIO Block with HW state
drm/rockchip: vop: report error when check resource error
drm/rockchip: vop: round_up pitches to word align
drm/rockchip: vop: fix NV12 video display error
drm/rockchip: vop: fix iommu page fault when resume
drm/i915/gvt: clean workload queue if error happened
drm/i915/gvt: change resetting to resetting_eng
drm/msm: gpu: don't abuse dma_alloc for non-DMA allocations
drm/msm: gpu: call qcom_mdt interfaces only for ARCH_QCOM
drm/msm/adreno: Prevent unclocked access when retrieving timestamps
drm/msm: Remove __user from __u64 data types
...
Merge misc fixes from Andrew Morton:
"21 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (21 commits)
userfaultfd: replace ENOSPC with ESRCH in case mm has gone during copy/zeropage
zram: rework copy of compressor name in comp_algorithm_store()
rmap: do not call mmu_notifier_invalidate_page() under ptl
mm: fix list corruptions on shmem shrinklist
mm/balloon_compaction.c: don't zero ballooned pages
MAINTAINERS: copy virtio on balloon_compaction.c
mm: fix KSM data corruption
mm: fix MADV_[FREE|DONTNEED] TLB flush miss problem
mm: make tlb_flush_pending global
mm: refactor TLB gathering API
Revert "mm: numa: defer TLB flush for THP migration as long as possible"
mm: migrate: fix barriers around tlb_flush_pending
mm: migrate: prevent racy access to tlb_flush_pending
fault-inject: fix wrong should_fail() decision in task context
test_kmod: fix small memory leak on filesystem tests
test_kmod: fix the lock in register_test_dev_kmod()
test_kmod: fix bug which allows negative values on two config options
test_kmod: fix spelling mistake: "EMTPY" -> "EMPTY"
userfaultfd: hugetlbfs: remove superfluous page unlock in VM_SHARED case
mm: ratelimit PFNs busy info message
...
When the process exit races with outstanding mcopy_atomic, it would be
better to return ESRCH error. When such race occurs the process and
it's mm are going away and returning "no such process" to the uffd
monitor seems better fit than ENOSPC.
Link: http://lkml.kernel.org/r/1502111545-32305-1-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Suggested-by: Michal Hocko <mhocko@suse.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Pavel Emelyanov <xemul@virtuozzo.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
comp_algorithm_store() passes the size of the source buffer to strlcpy()
instead of the destination buffer size. Make it explicit that the two
buffers have the same size and use strcpy() instead of strlcpy(). The
latter can be done safely since the function ensures that the string in
the source buffer is terminated.
Link: http://lkml.kernel.org/r/20170803163350.45245-1-mka@chromium.org
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We saw many list corruption warnings on shmem shrinklist:
WARNING: CPU: 18 PID: 177 at lib/list_debug.c:59 __list_del_entry+0x9e/0xc0
list_del corruption. prev->next should be ffff9ae5694b82d8, but was ffff9ae5699ba960
Modules linked in: intel_rapl sb_edac edac_core x86_pkg_temp_thermal coretemp iTCO_wdt iTCO_vendor_support crct10dif_pclmul crc32_pclmul ghash_clmulni_intel raid0 dcdbas shpchp wmi hed i2c_i801 ioatdma lpc_ich i2c_smbus acpi_cpufreq tcp_diag inet_diag sch_fq_codel ipmi_si ipmi_devintf ipmi_msghandler igb ptp crc32c_intel pps_core i2c_algo_bit i2c_core dca ipv6 crc_ccitt
CPU: 18 PID: 177 Comm: kswapd1 Not tainted 4.9.34-t3.el7.twitter.x86_64 #1
Hardware name: Dell Inc. PowerEdge C6220/0W6W6G, BIOS 2.2.3 11/07/2013
Call Trace:
dump_stack+0x4d/0x66
__warn+0xcb/0xf0
warn_slowpath_fmt+0x4f/0x60
__list_del_entry+0x9e/0xc0
shmem_unused_huge_shrink+0xfa/0x2e0
shmem_unused_huge_scan+0x20/0x30
super_cache_scan+0x193/0x1a0
shrink_slab.part.41+0x1e3/0x3f0
shrink_slab+0x29/0x30
shrink_node+0xf9/0x2f0
kswapd+0x2d8/0x6c0
kthread+0xd7/0xf0
ret_from_fork+0x22/0x30
WARNING: CPU: 23 PID: 639 at lib/list_debug.c:33 __list_add+0x89/0xb0
list_add corruption. prev->next should be next (ffff9ae5699ba960), but was ffff9ae5694b82d8. (prev=ffff9ae5694b82d8).
Modules linked in: intel_rapl sb_edac edac_core x86_pkg_temp_thermal coretemp iTCO_wdt iTCO_vendor_support crct10dif_pclmul crc32_pclmul ghash_clmulni_intel raid0 dcdbas shpchp wmi hed i2c_i801 ioatdma lpc_ich i2c_smbus acpi_cpufreq tcp_diag inet_diag sch_fq_codel ipmi_si ipmi_devintf ipmi_msghandler igb ptp crc32c_intel pps_core i2c_algo_bit i2c_core dca ipv6 crc_ccitt
CPU: 23 PID: 639 Comm: systemd-udevd Tainted: G W 4.9.34-t3.el7.twitter.x86_64 #1
Hardware name: Dell Inc. PowerEdge C6220/0W6W6G, BIOS 2.2.3 11/07/2013
Call Trace:
dump_stack+0x4d/0x66
__warn+0xcb/0xf0
warn_slowpath_fmt+0x4f/0x60
__list_add+0x89/0xb0
shmem_setattr+0x204/0x230
notify_change+0x2ef/0x440
do_truncate+0x5d/0x90
path_openat+0x331/0x1190
do_filp_open+0x7e/0xe0
do_sys_open+0x123/0x200
SyS_open+0x1e/0x20
do_syscall_64+0x61/0x170
entry_SYSCALL64_slow_path+0x25/0x25
The problem is that shmem_unused_huge_shrink() moves entries from the
global sbinfo->shrinklist to its local lists and then releases the
spinlock. However, a parallel shmem_setattr() could access one of these
entries directly and add it back to the global shrinklist if it is
removed, with the spinlock held.
The logic itself looks solid since an entry could be either in a local
list or the global list, otherwise it is removed from one of them by
list_del_init(). So probably the race condition is that, one CPU is in
the middle of INIT_LIST_HEAD() but the other CPU calls list_empty()
which returns true too early then the following list_add_tail() sees a
corrupted entry.
list_empty_careful() is designed to fix this situation.
[akpm@linux-foundation.org: add comments]
Link: http://lkml.kernel.org/r/20170803054630.18775-1-xiyou.wangcong@gmail.com
Fixes: 779750d20b ("shmem: split huge pages beyond i_size under memory pressure")
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit bb01b64cfa ("mm/balloon_compaction.c: enqueue zero page
to balloon device")'
Zeroing ballon pages is rather time consuming, especially when a lot of
pages are in flight. E.g. 7GB worth of ballooned memory takes 2.8s with
__GFP_ZERO while it takes ~491ms without it.
The original commit argued that zeroing will help ksmd to merge these
pages on the host but this argument is assuming that the host actually
marks balloon pages for ksm which is not universally true. So we pay
performance penalty for something that even might not be used in the end
which is wrong. The host can zero out pages on its own when there is a
need.
[mhocko@kernel.org: new changelog text]
Link: http://lkml.kernel.org/r/1501761557-9758-1-git-send-email-wei.w.wang@intel.com
Fixes: bb01b64cfa ("mm/balloon_compaction.c: enqueue zero page to balloon device")
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: zhenwei.pi <zhenwei.pi@youruncloud.com>
Cc: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changes to mm/balloon_compaction.c can easily break virtio, and virtio
is the only user of that interface. Add a line to MAINTAINERS so
whoever changes that file remembers to copy us.
Link: http://lkml.kernel.org/r/1501764010-24456-1-git-send-email-mst@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Rafael Aquini <aquini@redhat.com>
Acked-by: Wei Wang <wei.w.wang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nadav reported KSM can corrupt the user data by the TLB batching
race[1]. That means data user written can be lost.
Quote from Nadav Amit:
"For this race we need 4 CPUs:
CPU0: Caches a writable and dirty PTE entry, and uses the stale value
for write later.
CPU1: Runs madvise_free on the range that includes the PTE. It would
clear the dirty-bit. It batches TLB flushes.
CPU2: Writes 4 to /proc/PID/clear_refs , clearing the PTEs soft-dirty.
We care about the fact that it clears the PTE write-bit, and of
course, batches TLB flushes.
CPU3: Runs KSM. Our purpose is to pass the following test in
write_protect_page():
if (pte_write(*pvmw.pte) || pte_dirty(*pvmw.pte) ||
(pte_protnone(*pvmw.pte) && pte_savedwrite(*pvmw.pte)))
Since it will avoid TLB flush. And we want to do it while the PTE is
stale. Later, and before replacing the page, we would be able to
change the page.
Note that all the operations the CPU1-3 perform canhappen in parallel
since they only acquire mmap_sem for read.
We start with two identical pages. Everything below regards the same
page/PTE.
CPU0 CPU1 CPU2 CPU3
---- ---- ---- ----
Write the same
value on page
[cache PTE as
dirty in TLB]
MADV_FREE
pte_mkclean()
4 > clear_refs
pte_wrprotect()
write_protect_page()
[ success, no flush ]
pages_indentical()
[ ok ]
Write to page
different value
[Ok, using stale
PTE]
replace_page()
Later, CPU1, CPU2 and CPU3 would flush the TLB, but that is too late.
CPU0 already wrote on the page, but KSM ignored this write, and it got
lost"
In above scenario, MADV_FREE is fixed by changing TLB batching API
including [set|clear]_tlb_flush_pending. Remained thing is soft-dirty
part.
This patch changes soft-dirty uses TLB batching API instead of
flush_tlb_mm and KSM checks pending TLB flush by using
mm_tlb_flush_pending so that it will flush TLB to avoid data lost if
there are other parallel threads pending TLB flush.
[1] http://lkml.kernel.org/r/BD3A0EBE-ECF4-41D4-87FA-C755EA9AB6BD@gmail.com
Link: http://lkml.kernel.org/r/20170802000818.4760-8-namit@vmware.com
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Nadav Amit <namit@vmware.com>
Reported-by: Nadav Amit <namit@vmware.com>
Tested-by: Nadav Amit <namit@vmware.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Hugh Dickins <hughd@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nadav reported parallel MADV_DONTNEED on same range has a stale TLB
problem and Mel fixed it[1] and found same problem on MADV_FREE[2].
Quote from Mel Gorman:
"The race in question is CPU 0 running madv_free and updating some PTEs
while CPU 1 is also running madv_free and looking at the same PTEs.
CPU 1 may have writable TLB entries for a page but fail the pte_dirty
check (because CPU 0 has updated it already) and potentially fail to
flush.
Hence, when madv_free on CPU 1 returns, there are still potentially
writable TLB entries and the underlying PTE is still present so that a
subsequent write does not necessarily propagate the dirty bit to the
underlying PTE any more. Reclaim at some unknown time at the future
may then see that the PTE is still clean and discard the page even
though a write has happened in the meantime. I think this is possible
but I could have missed some protection in madv_free that prevents it
happening."
This patch aims for solving both problems all at once and is ready for
other problem with KSM, MADV_FREE and soft-dirty story[3].
TLB batch API(tlb_[gather|finish]_mmu] uses [inc|dec]_tlb_flush_pending
and mmu_tlb_flush_pending so that when tlb_finish_mmu is called, we can
catch there are parallel threads going on. In that case, forcefully,
flush TLB to prevent for user to access memory via stale TLB entry
although it fail to gather page table entry.
I confirmed this patch works with [4] test program Nadav gave so this
patch supersedes "mm: Always flush VMA ranges affected by zap_page_range
v2" in current mmotm.
NOTE:
This patch modifies arch-specific TLB gathering interface(x86, ia64,
s390, sh, um). It seems most of architecture are straightforward but
s390 need to be careful because tlb_flush_mmu works only if
mm->context.flush_mm is set to non-zero which happens only a pte entry
really is cleared by ptep_get_and_clear and friends. However, this
problem never changes the pte entries but need to flush to prevent
memory access from stale tlb.
[1] http://lkml.kernel.org/r/20170725101230.5v7gvnjmcnkzzql3@techsingularity.net
[2] http://lkml.kernel.org/r/20170725100722.2dxnmgypmwnrfawp@suse.de
[3] http://lkml.kernel.org/r/BD3A0EBE-ECF4-41D4-87FA-C755EA9AB6BD@gmail.com
[4] https://patchwork.kernel.org/patch/9861621/
[minchan@kernel.org: decrease tlb flush pending count in tlb_finish_mmu]
Link: http://lkml.kernel.org/r/20170808080821.GA31730@bbox
Link: http://lkml.kernel.org/r/20170802000818.4760-7-namit@vmware.com
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Nadav Amit <namit@vmware.com>
Reported-by: Nadav Amit <namit@vmware.com>
Reported-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, tlb_flush_pending is used only for CONFIG_[NUMA_BALANCING|
COMPACTION] but upcoming patches to solve subtle TLB flush batching
problem will use it regardless of compaction/NUMA so this patch doesn't
remove the dependency.
[akpm@linux-foundation.org: remove more ifdefs from world's ugliest printk statement]
Link: http://lkml.kernel.org/r/20170802000818.4760-6-namit@vmware.com
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Nadav Amit <namit@vmware.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is a preparatory patch for solving race problems caused by
TLB batch. For that, we will increase/decrease TLB flush pending count
of mm_struct whenever tlb_[gather|finish]_mmu is called.
Before making it simple, this patch separates architecture specific part
and rename it to arch_tlb_[gather|finish]_mmu and generic part just
calls it.
It shouldn't change any behavior.
Link: http://lkml.kernel.org/r/20170802000818.4760-5-namit@vmware.com
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Nadav Amit <namit@vmware.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While deferring TLB flushes is a good practice, the reverted patch
caused pending TLB flushes to be checked while the page-table lock is
not taken. As a result, in architectures with weak memory model (PPC),
Linux may miss a memory-barrier, miss the fact TLB flushes are pending,
and cause (in theory) a memory corruption.
Since the alternative of using smp_mb__after_unlock_lock() was
considered a bit open-coded, and the performance impact is expected to
be small, the previous patch is reverted.
This reverts b0943d61b8 ("mm: numa: defer TLB flush for THP migration
as long as possible").
Link: http://lkml.kernel.org/r/20170802000818.4760-4-namit@vmware.com
Signed-off-by: Nadav Amit <namit@vmware.com>
Suggested-by: Mel Gorman <mgorman@suse.de>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reading tlb_flush_pending while the page-table lock is taken does not
require a barrier, since the lock/unlock already acts as a barrier.
Removing the barrier in mm_tlb_flush_pending() to address this issue.
However, migrate_misplaced_transhuge_page() calls mm_tlb_flush_pending()
while the page-table lock is already released, which may present a
problem on architectures with weak memory model (PPC). To deal with
this case, a new parameter is added to mm_tlb_flush_pending() to
indicate if it is read without the page-table lock taken, and calling
smp_mb__after_unlock_lock() in this case.
Link: http://lkml.kernel.org/r/20170802000818.4760-3-namit@vmware.com
Signed-off-by: Nadav Amit <namit@vmware.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "fixes of TLB batching races", v6.
It turns out that Linux TLB batching mechanism suffers from various
races. Races that are caused due to batching during reclamation were
recently handled by Mel and this patch-set deals with others. The more
fundamental issue is that concurrent updates of the page-tables allow
for TLB flushes to be batched on one core, while another core changes
the page-tables. This other core may assume a PTE change does not
require a flush based on the updated PTE value, while it is unaware that
TLB flushes are still pending.
This behavior affects KSM (which may result in memory corruption) and
MADV_FREE and MADV_DONTNEED (which may result in incorrect behavior). A
proof-of-concept can easily produce the wrong behavior of MADV_DONTNEED.
Memory corruption in KSM is harder to produce in practice, but was
observed by hacking the kernel and adding a delay before flushing and
replacing the KSM page.
Finally, there is also one memory barrier missing, which may affect
architectures with weak memory model.
This patch (of 7):
Setting and clearing mm->tlb_flush_pending can be performed by multiple
threads, since mmap_sem may only be acquired for read in
task_numa_work(). If this happens, tlb_flush_pending might be cleared
while one of the threads still changes PTEs and batches TLB flushes.
This can lead to the same race between migration and
change_protection_range() that led to the introduction of
tlb_flush_pending. The result of this race was data corruption, which
means that this patch also addresses a theoretically possible data
corruption.
An actual data corruption was not observed, yet the race was was
confirmed by adding assertion to check tlb_flush_pending is not set by
two threads, adding artificial latency in change_protection_range() and
using sysctl to reduce kernel.numa_balancing_scan_delay_ms.
Link: http://lkml.kernel.org/r/20170802000818.4760-2-namit@vmware.com
Fixes: 2084140594 ("mm: fix TLB flush race between migration, and
change_protection_range")
Signed-off-by: Nadav Amit <namit@vmware.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 1203c8e6fb ("fault-inject: simplify access check for fail-nth")
unintentionally broke a conditional statement in should_fail(). Any
faults are not injected in the task context by the change when the
systematic fault injection is not used.
This change restores to the previous correct behaviour.
Link: http://lkml.kernel.org/r/1501633700-3488-1-git-send-email-akinobu.mita@gmail.com
Fixes: 1203c8e6fb ("fault-inject: simplify access check for fail-nth")
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reported-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Tested-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The break was in the wrong place so file system tests don't work as
intended, leaking memory at each test switch.
[mcgrof@kernel.org: massaged commit subject, noted memory leak issue without the fix]
Link: http://lkml.kernel.org/r/20170802211450.27928-6-mcgrof@kernel.org
Fixes: 39258f448d71 ("kmod: add test driver to stress test the module loader")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jessica Yu <jeyu@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Michal Marek <mmarek@suse.com>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We accidentally just drop the lock twice instead of taking it and then
releasing it. This isn't a big issue unless you are adding more than
one device to test on, and the kmod.sh doesn't do that yet, however this
obviously is the correct thing to do.
[mcgrof@kernel.org: massaged subject, explain what happens]
Link: http://lkml.kernel.org/r/20170802211450.27928-5-mcgrof@kernel.org
Fixes: 39258f448d71 ("kmod: add test driver to stress test the module loader")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: David Binderman <dcb314@hotmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jessica Yu <jeyu@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Michal Marek <mmarek@suse.com>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Parsing with kstrtol() enables values to be negative, and we failed to
check for negative values when parsing with test_dev_config_update_uint_sync()
or test_dev_config_update_uint_range().
test_dev_config_update_uint_range() has a minimum check though so an
issue is not present there. test_dev_config_update_uint_sync() is only
used for the number of threads to use (config_num_threads_store()), and
indeed this would fail with an attempt for a large allocation.
Although the issue is only present in practice with the first fix both
by using kstrtoul() instead of kstrtol().
Link: http://lkml.kernel.org/r/20170802211450.27928-4-mcgrof@kernel.org
Fixes: 39258f448d71 ("kmod: add test driver to stress test the module loader")
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: David Binderman <dcb314@hotmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jessica Yu <jeyu@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Michal Marek <mmarek@suse.com>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trivial fix to spelling mistake in snprintf text
[mcgrof@kernel.org: massaged commit message]
Link: http://lkml.kernel.org/r/20170802211450.27928-3-mcgrof@kernel.org
Fixes: 39258f448d71 ("kmod: add test driver to stress test the module loader")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Jessica Yu <jeyu@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michal Marek <mmarek@suse.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: David Binderman <dcb314@hotmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
huge_add_to_page_cache->add_to_page_cache implicitly unlocks the page
before returning in case of errors.
The error returned was -EEXIST by running UFFDIO_COPY on a non-hole
offset of a VM_SHARED hugetlbfs mapping. It was an userland bug that
triggered it and the kernel must cope with it returning -EEXIST from
ioctl(UFFDIO_COPY) as expected.
page dumped because: VM_BUG_ON_PAGE(!PageLocked(page))
kernel BUG at mm/filemap.c:964!
invalid opcode: 0000 [#1] SMP
CPU: 1 PID: 22582 Comm: qemu-system-x86 Not tainted 4.11.11-300.fc26.x86_64 #1
RIP: unlock_page+0x4a/0x50
Call Trace:
hugetlb_mcopy_atomic_pte+0xc0/0x320
mcopy_atomic+0x96f/0xbe0
userfaultfd_ioctl+0x218/0xe90
do_vfs_ioctl+0xa5/0x600
SyS_ioctl+0x79/0x90
entry_SYSCALL_64_fastpath+0x1a/0xa9
Link: http://lkml.kernel.org/r/20170802165145.22628-2-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Tested-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Alexey Perevalov <a.perevalov@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RDMA subsystem can generate several thousand of these messages per
second eventually leading to a kernel crash. Ratelimit these messages
to prevent this crash.
Doug said:
"I've been carrying a version of this for several kernel versions. I
don't remember when they started, but we have one (and only one) class
of machines: Dell PE R730xd, that generate these errors. When it
happens, without a rate limit, we get rcu timeouts and kernel oopses.
With the rate limit, we just get a lot of annoying kernel messages but
the machine continues on, recovers, and eventually the memory
operations all succeed"
And:
"> Well... why are all these EBUSY's occurring? It sounds inefficient
> (at least) but if it is expected, normal and unavoidable then
> perhaps we should just remove that message altogether?
I don't have an answer to that question. To be honest, I haven't
looked real hard. We never had this at all, then it started out of the
blue, but only on our Dell 730xd machines (and it hits all of them),
but no other classes or brands of machines. And we have our 730xd
machines loaded up with different brands and models of cards (for
instance one dedicated to mlx4 hardware, one for qib, one for mlx5, an
ocrdma/cxgb4 combo, etc), so the fact that it hit all of the machines
meant it wasn't tied to any particular brand/model of RDMA hardware.
To me, it always smelled of a hardware oddity specific to maybe the
CPUs or mainboard chipsets in these machines, so given that I'm not an
mm expert anyway, I never chased it down.
A few other relevant details: it showed up somewhere around 4.8/4.9 or
thereabouts. It never happened before, but the prinkt has been there
since the 3.18 days, so possibly the test to trigger this message was
changed, or something else in the allocator changed such that the
situation started happening on these machines?
And, like I said, it is specific to our 730xd machines (but they are
all identical, so that could mean it's something like their specific
ram configuration is causing the allocator to hit this on these
machine but not on other machines in the cluster, I don't want to say
it's necessarily the model of chipset or CPU, there are other bits of
identicalness between these machines)"
Link: http://lkml.kernel.org/r/499c0f6cc10d6eb829a67f2a4d75b4228a9b356e.1501695897.git.jtoppins@redhat.com
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Reviewed-by: Doug Ledford <dledford@redhat.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As Tetsuo points out:
"Commit 385386cff4 ("mm: vmstat: move slab statistics from zone to
node counters") broke "Slab:" field of /proc/meminfo . It shows nearly
0kB"
In addition to /proc/meminfo, this problem also affects the slab
counters OOM/allocation failure info dumps, can cause early -ENOMEM from
overcommit protection, and miscalculate image size requirements during
suspend-to-disk.
This is because the patch in question switched the slab counters from
the zone level to the node level, but forgot to update the global
accessor functions to read the aggregate node data instead of the
aggregate zone data.
Use global_node_page_state() to access the global slab counters.
Fixes: 385386cff4 ("mm: vmstat: move slab statistics from zone to node counters")
Link: http://lkml.kernel.org/r/20170801134256.5400-1-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 0cb64249ca ("firmware_loader: abort request if wait_for_completion
is interrupted") added via 4.0 added support to abort the fallback mechanism
when a signal was detected and wait_for_completion_interruptible() returned
-ERESTARTSYS -- for instance when a user hits CTRL-C. The abort was overly
*too* effective.
When a child process terminates (successful or not) the signal SIGCHLD can
be sent to the parent process which ran the child in the background and
later triggered a sync request for firmware through a sysfs interface which
relies on the fallback mechanism. This signal in turn can be recieved by the
interruptible wait we constructed on firmware_class and detects it as an
abort *before* userspace could get a chance to write the firmware. Upon
failure -EAGAIN is returned, so userspace is also kept in the dark about
exactly what happened.
We can reproduce the issue with the fw_fallback.sh selftest:
Before this patch:
$ sudo tools/testing/selftests/firmware/fw_fallback.sh
...
tools/testing/selftests/firmware/fw_fallback.sh: error - sync firmware request cancelled due to SIGCHLD
After this patch:
$ sudo tools/testing/selftests/firmware/fw_fallback.sh
...
tools/testing/selftests/firmware/fw_fallback.sh: SIGCHLD on sync ignored as expected
Fix this by making the wait killable -- only killable by SIGKILL (kill -9).
We loose the ability to allow userspace to cancel a write with CTRL-C
(SIGINT), however its been decided the compromise to require SIGKILL is
worth the gains.
Chances of this issue occuring are low due to the number of drivers upstream
exclusively relying on the fallback mechanism for firmware (2 drivers),
however this is observed in the field with custom drivers with sysfs
triggers to load firmware. Only distributions relying on the fallback
mechanism are impacted as well. An example reported issue was on Android,
as follows:
1) Android init (pid=1) fork()s (say pid=42) [this child process is totally
unrelated to firmware loading, it could be sleep 2; for all we care ]
2) Android init (pid=1) does a write() on a (driver custom) sysfs file which
ends up calling request_firmware() kernel side
3) The firmware loading fallback mechanism is used, the request is sent to
userspace and pid 1 waits in the kernel on wait_*
4) before firmware loading completes pid 42 dies (for any reason, even
normal termination)
5) Kernel delivers SIGCHLD to pid=1 to tell it a child has died, which
causes -ERESTARTSYS to be returned from wait_*
6) The kernel's wait aborts and return -EAGAIN for the
request_firmware() caller.
Cc: stable <stable@vger.kernel.org> # 4.0
Fixes: 0cb64249ca ("firmware_loader: abort request if wait_for_completion is interrupted")
Suggested-by: "Eric W. Biederman" <ebiederm@xmission.com>
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Martin Fuzzey <mfuzzey@parkeon.com>
Reported-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds