Replace hard coded "ACPI0007" with ACPI_PROCESSOR_DEVICE_HID
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Ankur Arora <ankur.a.arora@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
A new Dell laptop needs to apply ALC269_FIXUP_DELL1_MIC_NO_PRESENCE to
fix the headset problem, and the pin definiton of this machine is not
in the pin quirk table yet, now adding it to the table.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when Intel host controllers wait for the present
state to propagate.
The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.
Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when sdhci changes clock frequency because it
waits for the clock to become stable under a spin lock.
The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.
Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Since AQC-100/107/108 chips supports hardware checksums for RX we should indicate this
via NETIF_F_RXCSUM flag.
v1->v2: 'Signed-off-by' tag added.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ECC bit positions that describe whether the ECC interrupt is for
Tx, Rx or descriptor memory and whether the it is a single correctable
or double detected error were defined in incorrectly (reversed order).
Fix the bit position definitions for these settings so that the proper
ECC handling is performed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Presumably if there is an "add" function, there is also a "del"
function. But it causes a static checker warning because it looks like
a common cut and paste bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
compile-testing fails when QCOM_SMD is a loadable module:
drivers/bluetooth/built-in.o: In function `btqcomsmd_send':
btqca.c:(.text+0xa8): undefined reference to `qcom_smd_send'
drivers/bluetooth/built-in.o: In function `btqcomsmd_probe':
btqca.c:(.text+0x3ec): undefined reference to `qcom_wcnss_open_channel'
btqca.c:(.text+0x46c): undefined reference to `qcom_smd_set_drvdata'
This clarifies the dependency to allow compile-testing only when
SMD is completely disabled, otherwise the dependency on QCOM_SMD
will make sure we can link against it.
Fixes: e27ee2b16b ("Bluetooth: btqcomsmd: Allow driver to build if COMPILE_TEST is enabled")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[bjorn: Restructure and clarify dependency to QCOM_WCNSS_CTRL]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drm/i915 fixes for v4.11-rc4
* tag 'drm-intel-fixes-2017-03-22' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: make context status notifier head be per engine
drm/i915: Avoid rcu_barrier() from reclaim paths (shrinker)
drm/i915/gvt: Fix gvt scheduler interval time
drm/i915/gvt: GVT pin/unpin shadow context
drm/i915/gvt: scan shadow indirect context image when valid
drm/i915/kvmgt: fix suspicious rcu dereference usage
drm/i915/gvt: add enable_execlists check before enable gvt
drm/i915/gvt: Remove bogus retry around i915_wait_request
drm/i915/gvt: correct the ggtt valid bit check in pipe control command
drm/i915/gvt: replace the gvt_err with gvt_vgpu_err
drm/i915/gvt: handle force-nonpriv registers, cmd parser part
drm/i915: Do .init_clock_gating() earlier to avoid it clobbering watermarks
drm/i915/glk: Remove MODULE_FIRMWARE() tag from Geminilake's DMC
drm/i915: Reject HDMI 12bpc if the sink doesn't indicate support
drm/i915: Always call i915_gem_reset_finish() following i915_gem_reset_prepare()
drm/i915: Stop using RP_DOWN_EI on Baytrail
drm/i915: Drop support for I915_EXEC_CONSTANTS_* execbuf parameters.
drm/i915: Only enable hotplug interrupts if the display interrupts are enabled
drm/i915: Disable engine->irq_tasklet around resets
drm/i915: Split GEM resetting into 3 phases
icsk_ack.lrcvtime has a 0 value at socket creation time.
tcpi_last_data_recv can have bogus value if no payload is ever received.
This patch initializes icsk_ack.lrcvtime for active sessions
in tcp_finish_connect(), and for passive sessions in
tcp_create_openreq_child()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2ae0f17df1 ("genetlink: use idr to track families") replaced
if (++n < fams_to_skip)
continue;
into:
if (n++ < fams_to_skip)
continue;
This subtle change cause that on retry ctrl_dumpfamily() call we omit
one family that failed to do ctrl_fill_info() on previous call, because
cb->args[0] = n number counts also family that failed to do
ctrl_fill_info().
Patch fixes the problem and avoid confusion in the future just decrease
n counter when ctrl_fill_info() fail.
User visible problem caused by this bug is failure to get access to
some genetlink family i.e. nl80211. However problem is reproducible
only if number of registered genetlink families is big enough to
cause second call of ctrl_dumpfamily().
Cc: Xose Vazquez Perez <xose.vazquez@gmail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Fixes: 2ae0f17df1 ("genetlink: use idr to track families")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In sk_clone_lock(), we create a new socket and inherit most of the
parent's members via sock_copy() which memcpy()'s various sections.
Now, in case the parent socket had a BPF socket filter attached,
then newsk->sk_filter points to the same instance as the original
sk->sk_filter.
sk_filter_charge() is then called on the newsk->sk_filter to take a
reference and should that fail due to hitting max optmem, we bail
out and release the newsk instance.
The issue is that commit 278571baca ("net: filter: simplify socket
charging") wrongly combined the dismantle path with the failure path
of xfrm_sk_clone_policy(). This means, even when charging failed, we
call sk_free_unlock_clone() on the newsk, which then still points to
the same sk_filter as the original sk.
Thus, sk_free_unlock_clone() calls into __sk_destruct() eventually
where it tests for present sk_filter and calls sk_filter_uncharge()
on it, which potentially lets sk_omem_alloc wrap around and releases
the eBPF prog and sk_filter structure from the (still intact) parent.
Fix it by making sure that when sk_filter_charge() failed, we reset
newsk->sk_filter back to NULL before passing to sk_free_unlock_clone(),
so that we don't mess with the parents sk_filter.
Only if xfrm_sk_clone_policy() fails, we did reach the point where
either the parent's filter was NULL and as a result newsk's as well
or where we previously had a successful sk_filter_charge(), thus for
that case, we do need sk_filter_uncharge() to release the prior taken
reference on sk_filter.
Fixes: 278571baca ("net: filter: simplify socket charging")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander reported a KMSAN splat caused by reads of uninitialized
field (tb_id_in) from user provided struct fib_result_nl
It turns out nl_fib_input() sanity tests on user input is a bit
wrong :
User can pretend nlh->nlmsg_len is big enough, but provide
at sendmsg() time a too small buffer.
Reported-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In both kmalloc and prealloc mode the bpf_map_update_elem() is using
per-cpu extra_elems to do atomic update when the map is full.
There are two issues with it. The logic can be misused, since it allows
max_entries+num_cpus elements to be present in the map. And alloc_extra_elems()
at map creation time can fail percpu alloc for large map values with a warn:
WARNING: CPU: 3 PID: 2752 at ../mm/percpu.c:892 pcpu_alloc+0x119/0xa60
illegal size (32824) or align (8) for percpu allocation
The fixes for both of these issues are different for kmalloc and prealloc modes.
For prealloc mode allocate extra num_possible_cpus elements and store
their pointers into extra_elems array instead of actual elements.
Hence we can use these hidden(spare) elements not only when the map is full
but during bpf_map_update_elem() that replaces existing element too.
That also improves performance, since pcpu_freelist_pop/push is avoided.
Unfortunately this approach cannot be used for kmalloc mode which needs
to kfree elements after rcu grace period. Therefore switch it back to normal
kmalloc even when full and old element exists like it was prior to
commit 6c90598174 ("bpf: pre-allocate hash map elements").
Add tests to check for over max_entries and large map values.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Fixes: 6c90598174 ("bpf: pre-allocate hash map elements")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset")
removed the bcmgenet_mii_reset() function from bcmgenet_power_up() and
bcmgenet_internal_phy_setup() functions. In so doing it broke the reset
of the internal PHY devices used by the GENETv1-GENETv3 which required
this reset before the UniMAC was enabled. It also broke the internal
GPHY devices used by the GENETv4 because the config_init that installed
the AFE workaround was no longer occurring after the reset of the GPHY
performed by bcmgenet_phy_power_set() in bcmgenet_internal_phy_setup().
In addition the code in bcmgenet_internal_phy_setup() related to the
"enable APD" comment goes with the bcmgenet_mii_reset() so it should
have also been removed.
Commit bd4060a610 ("net: bcmgenet: Power on integrated GPHY in
bcmgenet_power_up()") moved the bcmgenet_phy_power_set() call to the
bcmgenet_power_up() function, but failed to remove it from the
bcmgenet_internal_phy_setup() function. Had it done so, the
bcmgenet_internal_phy_setup() function would have been empty and could
have been removed at that time.
Commit 5dbebbb44a ("net: bcmgenet: Software reset EPHY after power on")
was submitted to correct the functional problems introduced by
commit 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset"). It
was included in v4.4 and made available on 4.3-stable. Unfortunately,
it didn't fully revert the commit because this bcmgenet_mii_reset()
doesn't apply the soft reset to the internal GPHY used by GENETv4 like
the previous one did. This prevents the restoration of the AFE work-
arounds for internal GPHY devices after the bcmgenet_phy_power_set() in
bcmgenet_internal_phy_setup().
This commit takes the alternate approach of removing the unnecessary
bcmgenet_internal_phy_setup() function which shouldn't have been in v4.3
so that when bcmgenet_mii_reset() was restored it should have only gone
into bcmgenet_power_up(). This will avoid the problems while also
removing the redundancy (and hopefully some of the confusion).
Fixes: 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case udp_sk(sk)->pending is AF_INET6, udpv6_sendmsg() would
jump to do_append_data, skipping the initialization of sockc.tsflags.
Fix the problem by moving sockc.tsflags initialization earlier.
The bug was detected with KMSAN.
Fixes: c14ac9451c ("sock: enable timestamping using control messages")
Signed-off-by: Alexander Potapenko <glider@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YASUAKI ISHIMATSU says:
====================
fjes: Do not load fjes driver
The fjes driver is used only by FUJITSU servers and almost of all
servers in the world never use it. But currently if ACPI PNP0C02
is defined in the ACPI table, the following message is always shown:
"FUJITSU Extended Socket Network Device Driver - version 1.2
- Copyright (c) 2015 FUJITSU LIMITED"
The message makes users confused because there is no reason that
the message is shown in other vendor servers.
To avoid the confusion, the patch adds several checks.
v3:
- Rebase on latest net tree.
- Add _STA method check to avoid loading fjes driver.
v2:
- Order local variable declarations from longest to shortest line
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The extended device socket cannot turn on/off while system is running.
So when system boots up and the device is not power on, the fjes driver
does not need be loaded.
To check the status of the device, the patch adds ACPI _STA method check.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
CC: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fjes driver is used only by FUJITSU servers and almost of all
servers in the world never use it. But currently if ACPI PNP0C02
is defined in the ACPI table, the following message is always shown:
"FUJITSU Extended Socket Network Device Driver - version 1.2
- Copyright (c) 2015 FUJITSU LIMITED"
The message makes users confused because there is no reason that
the message is shown in other vendor servers.
To avoid the confusion, the patch adds a check that the server
has a extended socket device or not.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
CC: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX packets statistics ('rx_packets' counter) used to count LRO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'rx_lro_packets'
counter existence.
Before, ethtool showed:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 435277
rx_lro_packets: 35847
rx_packets_phy: 1935066
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 1935066
rx_lro_packets: 35847
rx_packets_phy: 1935066
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX packets statistics ('tx_packets' counter) used to count GSO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'tx_tso_packets'
counter existence.
Before, ethtool showed:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 61340
tx_tso_packets: 60954
tx_packets_phy: 2451115
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 2451115
tx_tso_packets: 60954
tx_packets_phy: 2451115
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With ConnectX-4 sharing SRQs from the same space as QPs, we hit a
limit preventing some applications to allocate needed QPs amount.
Double the size to 256K.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was added to allow the TC offloading code to identify offloading
encap/decap vxlan rules.
The VF reps are effectively related to the same mlx5 PCI device as the
PF. Since the kernel invokes the (say) delete ndo for each netdev, the
FW erred on multiple vxlan dst port deletes when the port was deleted
from the system.
We fix that by keeping the registration to be carried out only by the
PF. Since the PF serves as the uplink device, the VF reps will look
up a port there and realize if they are ok to offload that.
Tested:
<SETUP VFS>
<SETUP switchdev mode to have representors>
ip link add vxlan1 type vxlan id 44 dev ens5f0 dstport 9999
ip link set vxlan1 up
ip link del dev vxlan1
Fixes: 4a25730eb2 ('net/mlx5e: Add ndo_udp_tunnel_add to VF representors')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we use the non UAPI values and we miss erring on
the modify action which is not supported, fix that.
Fixes: 8b32580df1 ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the eswitch inline mode can potentially cause already configured
flows not to match the policy. E.g. set policy L4, add some L4 rules,
set policy to L2 --> bad! Hence we disallow it.
Keep track of how many offloaded rules are now set and refuse
inline mode changes if this isn't zero.
Fixes: bffaa91658 ("net/mlx5: E-Switch, Add control for inline mode")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the code to deal with add/del TC rules to have handler per NIC/E-switch
offloading use case, and push the latter into the e-switch code. This provides
better separation and is to be used in down-stream patch for applying a fix.
Fixes: bffaa91658 ("net/mlx5: E-Switch, Add control for inline mode")
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch cases for the rate limit set and query commands were
missing, which could get us wrong under fw error or driver reset
flow, fix that.
Fixes: 1466cc5b23 ('net/mlx5: Rate limit tables support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi
* fix a user reported warning in DQA
mwifiex
* fix a potential double free
* fix lost early debug logs
* fix init wakeup warning message from device framework
* add Ganapathi and Xinming as maintainers
ath10k
* fix regression with QCA6174 during resume and firmware crash
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY0S5DAAoJEG4XJFUm622bYoYH/AxiLF0UleRgeHeQAQd4d1d0
QsISkT+Xm1p43P3GQ9qoKocHd0S0GvWCqzHC2HAeDmLFAUf5gfo3hhGqEvTVEvCo
eUiNjIJyezNcvo9JJwmB/P8O2nVJH9tUtSISwKfnvG/XT4olSJfE+vPi0edOXG4s
IvDdO8AiuoZHoP11utNtMsg4vnA1uvy75ti20fe69PX5g9G/+gcDBkFHh/IpcfML
GSRZaZjKxsaWKnSUimPJlJsvsJE+mcsXD2rPImEiinQbR2yTfkAcmdxaQR9fkVSP
1FdT4MvWoxrK4sUaPSn3ZO/eVzNeDXi9bQPGQwBpq6rUZp7r9OPkdRqGWbi/hW8=
=zzBr
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.11
iwlwifi
* fix a user reported warning in DQA
mwifiex
* fix a potential double free
* fix lost early debug logs
* fix init wakeup warning message from device framework
* add Ganapathi and Xinming as maintainers
ath10k
* fix regression with QCA6174 during resume and firmware crash
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, tipc_nametbl_unsubscribe() is called at subscriptions
reference count cleanup. Usually the subscriptions cleanup is
called at subscription timeout or at subscription cancel or at
subscriber delete.
We have ignored the possibility of this being called from other
locations, which causes deadlock as we try to grab the
tn->nametbl_lock while holding it already.
CPU1: CPU2:
---------- ----------------
tipc_nametbl_publish
spin_lock_bh(&tn->nametbl_lock)
tipc_nametbl_insert_publ
tipc_nameseq_insert_publ
tipc_subscrp_report_overlap
tipc_subscrp_get
tipc_subscrp_send_event
tipc_close_conn
tipc_subscrb_release_cb
tipc_subscrb_delete
tipc_subscrp_put
tipc_subscrp_put
tipc_subscrp_kref_release
tipc_nametbl_unsubscribe
spin_lock_bh(&tn->nametbl_lock)
<<grab nametbl_lock again>>
CPU1: CPU2:
---------- ----------------
tipc_nametbl_stop
spin_lock_bh(&tn->nametbl_lock)
tipc_purge_publications
tipc_nameseq_remove_publ
tipc_subscrp_report_overlap
tipc_subscrp_get
tipc_subscrp_send_event
tipc_close_conn
tipc_subscrb_release_cb
tipc_subscrb_delete
tipc_subscrp_put
tipc_subscrp_put
tipc_subscrp_kref_release
tipc_nametbl_unsubscribe
spin_lock_bh(&tn->nametbl_lock)
<<grab nametbl_lock again>>
In this commit, we advance the calling of tipc_nametbl_unsubscribe()
from the refcount cleanup to the intended callers.
Fixes: d094c4d5f5 ("tipc: add subscription refcount to avoid invalid delete")
Reported-by: John Thompson <thompa.atl@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the unnecessary temporary variable 'err' from
sctp_association_init.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_stream_free uses struct sctp_stream as a param, but struct sctp_stream
is defined after it's declaration.
This patch is to declare struct sctp_stream before sctp_stream_free.
Fixes: a83863174a ("sctp: prepare asoc stream for stream reconf")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With posix timers having become optional, we get a build error with
the cpts time sync option of the CPSW driver:
drivers/net/ethernet/ti/cpts.c: In function 'cpts_find_ts':
drivers/net/ethernet/ti/cpts.c:291:23: error: implicit declaration of function 'ptp_classify_raw';did you mean 'ptp_classifier_init'? [-Werror=implicit-function-declaration]
This adds a hard dependency on PTP_CLOCK to avoid the problem, as
building it without PTP support makes no sense anyway.
Fixes: baa73d9e47 ("posix-timers: Make them configurable")
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dependency is reversed: cpsw and netcp call into cpts,
but cpts depends on the other two in Kconfig. This can lead
to cpts being a loadable module and its callers built-in:
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_remove':
cpsw.c:(.text.cpsw_remove+0xd0): undefined reference to `cpts_release'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_rx_handler':
cpsw.c:(.text.cpsw_rx_handler+0x2dc): undefined reference to `cpts_rx_timestamp'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_tx_handler':
cpsw.c:(.text.cpsw_tx_handler+0x7c): undefined reference to `cpts_tx_timestamp'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_ndo_stop':
As a workaround, I'm introducing another Kconfig symbol to
control the compilation of cpts, while making the actual
module controlled by a silent symbol that is =y when necessary.
Fixes: 6246168b4a ("net: ethernet: ti: netcp: add support of cpts")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang says:
====================
r8152: fix the rx settings of RTL8153
The RMS and the rx early size should base on the same rx size. However,
the RMS is set to 9K bytes now and the rx early depends on mtu. For using
the rx buffer effectively, sync the two settings according to the mtu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
revert commit a59e6d8152 ("r8152: correct the rx early size") and
fix the rx early size as
(rx buffer size - rx packet size - rx desc size - alignment) / 4
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the received maximum size (RMS) according to the mtu size. It is
unnecessary to receive a packet which is more than the size we could
transmit. Besides, this could let the rx buffer be used effectively.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The net_cls controller controls the classid field of each socket which
is associated with the cgroup. Because the classid is per-socket
attribute, when a task migrates to another cgroup or the configured
classid of the cgroup changes, the controller needs to walk all
sockets and update the classid value, which was implemented by
3b13758f51 ("cgroups: Allow dynamically changing net_classid").
While the approach is not scalable, migrating tasks which have a lot
of fds attached to them is rare and the cost is born by the ones
initiating the operations. However, for simplicity, both the
migration and classid config change paths call update_classid() which
scans all fds of all tasks in the target css. This is an overkill for
the migration path which only needs to cover a much smaller subset of
tasks which are actually getting migrated in.
On cgroup v1, this can lead to unexpected scalability issues when one
tries to migrate a task or process into a net_cls cgroup which already
contains a lot of fds. Even if the migration traget doesn't have many
to get scanned, update_classid() ends up scanning all fds in the
target cgroup which can be extremely numerous.
Unfortunately, on cgroup v2 which doesn't use net_cls, the problem is
even worse. Before bfc2cf6f61 ("cgroup: call subsys->*attach() only
for subsystems which are actually affected by migration"), cgroup core
would call the ->css_attach callback even for controllers which don't
see actual migration to a different css.
As net_cls is always disabled but still mounted on cgroup v2, whenever
a process is migrated on the cgroup v2 hierarchy, net_cls sees
identity migration from root to root and cgroup core used to call
->css_attach callback for those. The net_cls ->css_attach ends up
calling update_classid() on the root net_cls css to which all
processes on the system belong to as the controller isn't used. This
makes any cgroup v2 migration O(total_number_of_fds_on_the_system)
which is horrible and easily leads to noticeable stalls triggering RCU
stall warnings and so on.
The worst symptom is already fixed in upstream by bfc2cf6f61
("cgroup: call subsys->*attach() only for subsystems which are
actually affected by migration"); however, backporting that commit is
too invasive and we want to avoid other cases too.
This patch updates net_cls's cgrp_attach() to iterate fds of only the
processes which are actually getting migrated. This removes the
surprising migration cost which is dependent on the total number of
fds in the target cgroup. As this leaves write_classid() the only
user of update_classid(), open-code the helper into write_classid().
Reported-by: David Goode <dgoode@fb.com>
Fixes: 3b13758f51 ("cgroups: Allow dynamically changing net_classid")
Cc: stable@vger.kernel.org # v4.4+
Cc: Nina Schiff <ninasc@fb.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cache related issues with DMA rings and performance issues related to
caching are being caused by not properly setting the "dma-coherent" flag
in the device tree entries. Adding it here to correct the issue.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: fd5e5dd56 ("arm64: dts: Add PCIe0 and PCIe4 DT nodes for NS2")
Fixes: dddc3c9d7 ("arm64: dts: NS2: add AMAC ethernet support")
Fixes: e79249143 ("arm64: dts: Add Broadcom Northstar2 device tree entries for PDC driver")
Fixes: ac9aae00f ("arm64: dts: Add SATA3 AHCI and SATA3 PHY DT nodes for NS2")
Fixes: efc877676 ("arm64: dts: Add SDHCI DT node for NS2")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
If kernel image extends across alignment boundary, existing
code increases the KASLR offset by size of kernel image. The
offset is masked after resizing. There are cases, where after
masking, we may still have kernel image extending across
boundary. This eventually results in only 2MB block getting
mapped while creating the page tables. This results in data aborts
while accessing unmapped regions during second relocation (with
kaslr offset) in __primary_switch. To fix this problem, round up the
kernel image size, by swapper block size, before adding it for
correction.
For example consider below case, where kernel image still crosses
1GB alignment boundary, after masking the offset, which is fixed
by rounding up kernel image size.
SWAPPER_TABLE_SHIFT = 30
Swapper using section maps with section size 2MB.
CONFIG_PGTABLE_LEVELS = 3
VA_BITS = 39
_text : 0xffffff8008080000
_end : 0xffffff800aa1b000
offset : 0x1f35600000
mask = ((1UL << (VA_BITS - 2)) - 1) & ~(SZ_2M - 1)
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7c
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
offset after existing correction (before mask) = 0x1f37f9b000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
offset (after mask) = 0x1f37e00000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7c
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
new offset w/ rounding up = 0x1f38000000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
Fixes: f80fb3a3d5 ("arm64: add support for kernel ASLR")
Cc: <stable@vger.kernel.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The introduction of reserved regions has left a couple of rough edges
which we could do with sorting out sooner rather than later. Since we
are not yet addressing the potential dynamic aspect of software-managed
reservations and presenting them at arbitrary fixed addresses, it is
incongruous that we end up displaying hardware vs. software-managed MSI
regions to userspace differently, especially since ARM-based systems may
actually require one or the other, or even potentially both at once,
(which iommu-dma currently has no hope of dealing with at all). Let's
resolve the former user-visible inconsistency ASAP before the ABI has
been baked into a kernel release, in a way that also lays the groundwork
for the latter shortcoming to be addressed by follow-up patches.
For clarity, rename the software-managed type to IOMMU_RESV_SW_MSI, use
IOMMU_RESV_MSI to describe the hardware type, and document everything a
little bit. Since the x86 MSI remapping hardware falls squarely under
this meaning of IOMMU_RESV_MSI, apply that type to their regions as well,
so that we tell the same story to userspace across all platforms.
Secondly, as the various region types require quite different handling,
and it really makes little sense to ever try combining them, convert the
bitfield-esque #defines to a plain enum in the process before anyone
gets the wrong impression.
Fixes: d30ddcaa7b ("iommu: Add a new type field in iommu_resv_region")
Reviewed-by: Eric Auger <eric.auger@redhat.com>
CC: Alex Williamson <alex.williamson@redhat.com>
CC: David Woodhouse <dwmw2@infradead.org>
CC: kvm@vger.kernel.org
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
For some unknown reasons, in some cases, FLPD cache invalidation doesn't
work properly with SYSMMU v5 controllers found in Exynos5433 SoCs. This
can be observed by a firmware crash during initialization phase of MFC
video decoder available in the mentioned SoCs when IOMMU support is
enabled. To workaround this issue perform a full TLB/FLPD invalidation
in case of replacing any first level page descriptors in case of SYSMMU v5.
Fixes: 740a01eee9 ("iommu/exynos: Add support for v5 SYSMMU")
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Documentation specifies that SYSMMU should be in blocked state while
performing TLB/FLPD cache invalidation, so add needed calls to
sysmmu_block/unblock.
Fixes: 66a7ed84b3 ("iommu/exynos: Apply workaround of caching fault page table entries")
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In the case of semi planar formats cb and cr are in the same plane
in memory, meaning that will be set to 'cb' whatever the format is,
and whatever the (packed) order of those components are.
Suggested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Thibault Saunier <thibault.saunier@osg.samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The File handle is not yet added in the vdev list.So no need to call
v4l2_fh_del(&ctx->fh)if it fails to create control.
Signed-off-by: Shailendra Verma <shailendra.v@samsung.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Ankur Arora