This patch avoids dereferencing msm_host->dev when it is NULL.
If we find ourselves tearing down dsi before calling
(mdp4|mdp5|dpu)_kms_init(), we'll end up in a state where the dev
pointer is NULL and trying to extract priv from it will fail.
This was introduced in a seemingly innocuous commit to ensure the
arguments to msm_gem_put_iova() are correct (even though that
function has been a stub for ~5 years). Correctness FTW! \o/
Fixes: b01884a286b0 drm/msm: use correct aspace pointer in msm_gem_put_iova()
Cc: Daniel Mack <daniel@zonque.org>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Even though msm_gem_put_iova() is currently a NOP function, the caller
should pass in the address space pointer it used to obtain the object.
Other call sites were changed in 8bdcd949bb ("drm/msm: pass
address-space to _get_iova() and friends"), but this one seems to have
been forgotten.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This regression stems from 0e08270a1f ("drm/msm: Separate locking of
buffer resources from struct_mutex").
Signed-off-by: Daniel Mack <daniel@zonque.org>
Cc: Sushmita Susheelendra <ssusheel@codeaurora.org>
Cc: Rob Clark <rclark@redhat.com>
Fixes: 0e08270a1f ("drm/msm: Separate locking of buffer resources from struct_mutex")
Signed-off-by: Rob Clark <robdclark@gmail.com>
The function dsi_get_cmd_fmt returns enum dsi_cmd_dst_format,
use the correct enum value also for MIPI_DSI_FMT_RGB666/_PACKED.
This has been discovered using clang:
drivers/gpu/drm/msm/dsi/dsi_host.c:743:35: warning: implicit conversion
from enumeration type 'enum dsi_vid_dst_format' to different
enumeration type 'enum dsi_cmd_dst_format' [-Wenum-conversion]
case MIPI_DSI_FMT_RGB666: return VID_DST_FORMAT_RGB666;
~~~~~~ ^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently the DSI PHY timings are hard-coded for a specific panel
for the 10nm PHY.
Replace this with the auto PHY timing calculator which can calculate
the PHY timings for any panel.
Changes in v4:
- None
Changes in v3:
- None
Changes in v2:
- None
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Make sure the video mode engine is on before waiting
for the video done interrupt.
Changes in v4:
- Move setting enabled to false earlier
Changes in v3:
- Move the return value check to another
patch
Changes in v2:
- Replace pr_err with dev_err
- Changed error message
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Check for the return value of wait for video
done waits and print appropriate error message.
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This should be using drm_gem_object_put(). Also since this is done only
in driver unload path, we don't need to synchronize setting tx_gem_obj
to NULL, so juse use the _unlocked() variant.
Signed-off-by: Rob Clark <robdclark@gmail.com>
_dev_ is being dereferenced before it is null checked, hence there
is a potential null pointer dereference.
Fix this by moving the pointer dereference after _dev_ has been
null checked.
Fixes: d4e7f38d70ef ("drm/msm/dsi: check msm_dsi and dsi pointers before use")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Newer DSI host controllers (SDM845 in particular) require a new clock
called byte_intf_clk. A recent patch tried to add this as an optional
clock, but it still set 'ret' to an error number if it didn't find it.
This breaks the host's probe for all previous DSI host versions.
Instead of setting this up as an optional clock, try to get the clock
only for the DSI version that supports it.
Fixes: 56558fb ("drm/msm/dsi: Add byte_intf_clk")
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI6G v2.0+ blocks have a new clock input to them called
byte_intf_clk. It's rate is to be set as byte_clk / 2.
Within the clock controller (CC) subsystem, this clock is a
child/descendant of the byte_clk.
Set it up as an optional clock in the DSI host driver. Make sure
that we enable/set its rate only after we configure byte_clk.
This is required for the ancestor clocks in the CC to be
configured correctly.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
SDM845 contains 2 DSI6G v2.2.1 host controllers. Add them in dsi_cfg.
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We try to get the interface clock in dsi_get_config early during DSI's
component bind. Try getting both the "iface" and "iface_clk" clock name
variants so that we are compatible with both new and legacy DT.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Populate the PHY ops with the downstream driver as reference.
There are a couple of TODOs which need to be resolved:
- The PHY timings are all hardcoded for now. This needs to be replaced
with automatic calculations once we get/understand them.
- There are some lane configuration registers which use a new
representation between physical and logical lane mappings. For now,
we've hardcoced them to follow the default mapping (i.e
logical 0 -> phy 0, logical 1 -> phy 1 etc).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Populate PLL clock ops from downstream. This contains the VCO PLL
ops and the registration of standard clk_divider and clk_mux clocks.
Unlike 14nm PLL, the postdividers/mux of the slave PLL doesn't need
to be set to the same values of the postdivs/mux of the master PLL.
Hence, we don't need special postdivider clock ops like we did with
the 14nm PLL driver.
Like the previous PLL drivers, the implementation is slightly different
from downstream. We don't use shadow clocks, but have the ability to
reparent the RCGs to a different source.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add new 10nm DSI PLL/PHY files that will be used on SDM845.
Just populate empty pll/phy funcs for now. These will be filled up
later.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Move null checks of pointer arguments to the beginning of the
modeset init function since they are referenced immediately
instead of after they have already been used.
Signed-off-by: Lloyd Atkinson <latkinso@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Check DSI instance id argument against the proper boundary size
to protect against invalid configuration of the DSI id.
Signed-off-by: Lloyd Atkinson <latkinso@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Make msm_dsi_pll_init consistently return an error code instead
of NULL when pll initialization fails so that later pll
retrieval can check against an error code. Add checks for these
failures after retrieval of src_pll to avoid invalid pointer
dereferences later in msm_dsi_pll_get_clk_provider.
Signed-off-by: Lloyd Atkinson <latkinso@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
divider_recalc_rate() is an helper function used by clock divider of
different types, so the structure containing the 'hw' pointer is not
always a 'struct clk_divider'
At the following line:
> div = _get_div(table, val, flags, divider->width);
in several cases, the value of 'divider->width' is garbage as the actual
structure behind this memory is not a 'struct clk_divider'
Fortunately, this width value is used by _get_val() only when
CLK_DIVIDER_MAX_AT_ZERO flag is set. This has never been the case so
far when the structure is not a 'struct clk_divider'. This is probably
why we did not notice this bug before
Fixes: afe76c8fd0 ("clk: allow a clk divider with max divisor when zero")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZ9kEFAAoJEHm+PkMAQRiGw6wH/0j197qyGd0hkVFMJO6LAgN3
KQWS4nZ5BkVDocwv0RVnUJTtXqU1eozFgdVEtSoaFXpzlHGuptR2Tau9efDCJ7w3
/utZxqvhGebZd2T+j+/o/LE8BRQxhADBNJq2D/o0WNt8ecxuG0GIkhkEYt/o3z1v
/sxlwVwzXB7Dc/h1WcgGJG7cS6L9KzzAzGAS/iNvdFrPOygHBv8c0MxVZIiBIeeK
1nZdyvbyM8uenSyG+prGt9ENrqXZxxfwUxIchi2V7A9m1WmD5zijNkf1JCWji/O+
UsA1auxna7MwoxjxqZuGm4MlKOwZ+8xutk4JGgc+aP/ulndJbJYu+4op/3vaFBM=
=Mhx+
-----END PGP SIGNATURE-----
Backmerge tag 'v4.14-rc7' into drm-next
Linux 4.14-rc7
Requested by Ben Skeggs for nouveau to avoid major conflicts,
and things were getting a bit conflicty already, esp around amdgpu
reverts.
We already have, as a result of upstreaming the gpu bindings,
msm_clk_get() which will try to get the clock both without and with a
"_clk" suffix. Use this in DSI code so we can drop the "_clk" suffix
in bindings while maintaing backwards compatibility.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
The DSI runtime PM suspend/resume callbacks check whether
msm_host->cfg_hnd is non-NULL before trying to enable the bus clocks.
This is done to accommodate early calls to these functions that may
happen before the bus clocks are even initialized.
Calling pm_runtime_put_autosuspend() in dsi_host_init() can result in
racy behaviour since msm_host->cfg_hnd is set very soon after. If the
suspend callback happens too late, we end up trying to disable clocks
that were never enabled, resulting in a bunch of WARN_ON splats.
Use pm_runtime_put_sync() so that the suspend callback is called
immediately.
Reported-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Updates for 4.14.. I have some further patches from Jordan to add
multiple priority levels and pre-emption, but those will probably be
for 4.15 to give me time for the mesa parts.
* tag 'drm-msm-next-2017-08-22' of git://people.freedesktop.org/~robclark/linux:
drm/msm/mdp5: mark runtime_pm functions as __maybe_unused
drm/msm: remove unused variable
drm/msm/mdp5: make helper function static
drm/msm: make msm_framebuffer_init() static
drm/msm: add helper to allocate stolen fb
drm/msm: don't track fbdev's gem object separately
drm/msm: add modeset module param
drm/msm/mdp5: add tracking for clk enable-count
drm/msm: remove unused define
drm/msm: Add a helper function for in-kernel buffer allocations
drm/msm: Attach the GPU MMU when it is created
drm/msm: Add A5XX hardware fault detection
drm/msm: Remove uneeded platform dev members
drm/msm/mdp5: Set up runtime PM for MDSS
drm/msm/mdp5: Write to SMP registers even if allocations don't change
drm/msm/mdp5: Don't use mode_set helper funcs for encoders and CRTCs
drm/msm/dsi: Implement RPM suspend/resume callbacks
drm/msm/dsi: Set up runtime PM for DSI
drm/msm/hdmi: Set up runtime PM for HDMI
drm/msm/mdp5: Use runtime PM get/put API instead of toggling clocks
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZkNpUAAoJEHm+PkMAQRiGr68H/2nr8kxpoUhZ7eA5C71waCjh
gnJSevkzJAp+fCb0KfQFAp1qvpmLLle4e6tAxYgTQZg4Z3W5cJJNfxu9TzY5sGuL
o9QUr43XzABepW4e4jhRtZv6dj3K6XruNeDQKXDZTDcc/S8zoiS/Pltq7VgPcAuM
kX+3qsNdUyknngD6b0z9NtJkb0mHKY6J8MpraWRO34egDwsaN/tuhRj0DRQpCoyQ
x/k+hMbc9MB9Dn8cfACo6Omb+r5Rfd7dTBUAju/TnIIgs//9voHba307N7XvLJZg
kWc8MqMQQZXfRZHB0atpDMHyZS/XQRlNPXj76j0+Ud/byODKTFkkazmgTpALvj8=
=CxeU
-----END PGP SIGNATURE-----
Backmerge tag 'v4.13-rc5' into drm-next
Linux 4.13-rc5
There's a really nasty nouveau collision, hopefully someone can take a look
once I pushed this out.
It's dead code, the core handles all this directly now.
The only special case is nouveau and tda988x which used one function
for both legacy modeset code and -nv50 atomic world instead of 2
vtables. But amounts to exactly the same.
v2: Rebase over the panel/brideg refactorings in stm/ltdc.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@collabora.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Yakir Yang <kuankuan.y@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Romain Perier <romain.perier@collabora.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Hai Li <hali@codeaurora.org>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Cc: zain wang <wzz@rock-chips.com>
Cc: Baoyou Xie <baoyou.xie@linaro.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-8-daniel.vetter@ffwll.ch
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Philippe Cornu <philippe.cornu@st.com> (on stm)
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
The bus clocks are always enabled/disabled along with the power
domain, so move it to the runtime suspend/resume ops. This cleans
up the clock code a bit. Get rid of the clk_mutex mutex since it
isn't needed.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Call the pm_runtime_get/put API where we need the clocks enabled.
The main entry/exit points are 1) enabling/disabling the DSI bridge
and 2) Sending commands from the DSI host to the device.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
After the commit mentioned below, we start computing the byte and pixel
clocks (dsi_calc_clk_rate) in the DSI bridge's mode_set() op. The
calculation involves the number of DSI lanes being used by the
downstream bridge/panel.
If the downstream bridge/panel tries to change the number of DSI lanes
(as done in the ADV7533 driver) in its mode_set() op, then our DSI
host driver will not have the correct number of lanes when computing
byte/pixel clocks.
Fix this by delaying the clock rate calculation in the DSI bridge
enable path. In particular, compute the clock rates in
msm_dsi_host_get_phy_clk_req().
This fixes the DSI host error interrupts seen when we try to switch
between modes that require different number of lanes (4 to 3 lanes, or
vice versa) on db410c. The error interrupts occur since the byte/pixel
clock rates aren't according to what the DSI video mode timing engine
expects.
Fixes: b62aa70a98 ("drm/msm/dsi: Move PHY operations out of host")
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Buffer object specific resources like pages, domains, sg list
need not be protected with struct_mutex. They can be protected
with a buffer object level lock. This simplifies locking and
makes it easier to avoid potential recursive locking scenarios
for SVM involving mmap_sem and struct_mutex. This also removes
unnecessary serialization when creating buffer objects, and also
between buffer object creation and GPU command submission.
Signed-off-by: Sushmita Susheelendra <ssusheel@codeaurora.org>
[robclark: squash in handling new locking for shrinker]
Signed-off-by: Rob Clark <robdclark@gmail.com>
No functional change, that will come later. But this will make it
easier to deal with dynamically created address spaces (ie. per-
process pagetables for gpu).
Signed-off-by: Rob Clark <robdclark@gmail.com>
Before we can shift to passing the address-space object to _get_iova(),
we need to fix a few places (dsi+fbdev) that were hard-coding the adress
space id. That gets somewhat easier if we just move these to the kms
base class.
Prep work for next patch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Include <drm/*.h> instead of relative path from include/drm, then
remove the -Iinclude/drm compiler flag.
While we are here, sort the touched parts with public headers first.
mdp4_kms.h must declare struct device_node to be self-contained.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1493009447-31524-11-git-send-email-yamada.masahiro@socionext.com
Last drm-misc-next pull req for 4.12
Core changes:
- fb_helper checkpatch cleanup and simplified _add_one_connector() (Thierry)
- drm_ioctl and drm_sysfs improved/gained documentation (Daniel)
- [ABI] Repurpose reserved field in drm_event_vblank for crtc_id (Ander)
- Plumb acquire ctx through legacy paths to avoid lock_all and legacy_backoff
(Daniel)
- Add connector_atomic_check to check conn constraints on modeset (Maarten)
- Add drm_of_find_panel_or_bridge to remove boilerplate in drivers (Rob)
Driver changes:
- meson moved to drm-misc (Neil)
- Added support for Amlogic GX SoCs in dw-hdmi (Neil)
- Rockchip unbind actually cleans up the things bind initializes (Jeffy)
- A couple misc fixes in virtio, dw-hdmi
NOTE: this also includes a backmerge of drm-next as well rc5 (we needed vmwgfx
as well as the new synopsys media formats)
* tag 'drm-misc-next-2017-04-07' of git://anongit.freedesktop.org/git/drm-misc: (77 commits)
Revert "drm: Don't allow interruptions when opening debugfs/crc"
drm: Only take cursor locks when the cursor plane exists
drm/vmwgfx: Fix fbdev emulation using legacy functions
drm/rockchip: Shutdown all crtcs when unbinding drm
drm/rockchip: Reorder drm bind/unbind sequence
drm/rockchip: analogix_dp: Disable clock when unbinding
drm/rockchip: vop: Unprepare clocks when unbinding
drm/rockchip: vop: Enable pm domain before vop_initial
drm/rockchip: cdn-dp: Don't unregister audio dev when unbinding
drm/rockchip: cdn-dp: Don't try to release firmware when not loaded
drm: bridge: analogix: Destroy connector & encoder when unbinding
drm: bridge: analogix: Disable clock when unbinding
drm: bridge: analogix: Unregister dp aux when unbinding
drm: bridge: analogix: Detach panel when unbinding analogix dp
drm: Don't allow interruptions when opening debugfs/crc
drm/virtio: don't leak bo on drm_gem_object_init failure
drm: bridge: dw-hdmi: fix input format/encoding from plat_data
drm: omap: use common OF graph helpers
drm: convert drivers to use drm_of_find_panel_or_bridge
drm: convert drivers to use of_graph_get_remote_node
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJY6mY1AAoJEHm+PkMAQRiGB14IAImsH28JPjxJVDasMIRPBxVc
euPPlZgoBieu7sNt+kEsEqdkXuu0MLk6gln0IGxWLeoB2S+u3Tz5LMa2YArVqV9Z
tWzOnI9auE73P2Pz/tUMOdyMs5tO0PolQxX3uljbULBozOHjHRh13fsXchX2yQvl
mFeFCDqpPV0KhWRH/ciA8uIHdvYPhMpkKgRtmR8jXL0yzqLp6+2J+Bs8nHG4NNng
HMVxZPC8jOE/TgWq6k/GmXgxh3H/AideFdHFbLKYnIFJW41ZGOI8a262zq3NmjPd
lywpVU7O7RMhSITY5PnuR3LpNV8ftw1hz2y6t35unyFK1P02adOSj5GJ3hGdhaQ=
=Xz5O
-----END PGP SIGNATURE-----
Backmerge tag 'v4.11-rc6' into drm-next
Linux 4.11-rc6
drm-misc needs 4.11-rc5, may as well fix conflicts with rc6.
Convert drivers to use the new of_graph_get_remote_node() helper
instead of parsing the endpoint node and then getting the remote device
node. Now drivers can just specify the device node and which
port/endpoint and get back the connected remote device node. The details
of the graph binding are nicely abstracted into the core OF graph code.
This changes some error messages to debug messages (in the graph core).
Graph connections are often "no connects" depending on the particular
board, so we want to avoid spurious messages. Plus the kernel is not a
DT validator.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Liviu Dudau <liviu.dudau@arm.com>
Tested-by: Eric Anholt <eric@anholt.net>
Tested-by: Jyri Sarha <jsarha@ti.com>
Tested by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
A recent commit introduces a bug in dsi_mgr_phy_enable. In the non
dual DSI mode, we reset the mdsi (master DSI) PHY. This isn't right
since master and slave DSI exist only in dual DSI mode. For the normal
mode of operation, we should simply reset the PHY of the DSI device
(i.e. msm_dsi) corresponding to the current bridge.
Usage of the wrong DSI pointer also resulted in a static checker
warning. That too is resolved with this fix.
Fixes: b62aa70a98 (drm/msm/dsi: Move PHY operations out of host)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Backmerge the main pull request to sync up with all the newly landed
drivers. Otherwise we'll have chaos even before 4.12 started in
earnest.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Extend the DSI PHY/PLL drivers to support the DSI 14nm PHY/PLL
found on 8x96.
These are picked up from the downstream driver. The PHY part is similar
to the other DSI PHYs. The PLL driver requires some trickery so that
one DSI PLL can drive both the DSIs (i.e, dual DSI mode).
In the case of dual DSI mode. One DSI instance becomes the clock master,
and other the clock slave. The master PLL's output (Byte and Pixel clock)
is fed to both the DSI hosts/PHYs.
When the DSIs are configured in dual DSI mode, the PHY driver communicates
to the PLL driver using msm_dsi_pll_set_usecase() which instance is the
master and which one is the slave. When setting rate, the master PLL also
configures some of the slave PLL/PHY registers which need to be identical
to the master's for correct dual DSI behaviour.
There are 2 PLL post dividers that should have ideally been modelled as
generic clk_divider clocks, but require some customization for dual DSI.
In particular, when the master PLL's post-diviers are set, the slave PLL's
post-dividers need to be set too. The clk_ops for these use clk_divider's
helper ops and flags internally to prevent redundant code.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The 14nm DSI PHY on 8x96 (called PHY v2 downstream) requires a different
set of calculations for computing D-PHY timing params. Create a
timing_calc_v2 func for the newer v2 PHYs.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since DSI PHY has been a separate platform device, it should not
depend on the resources in host to be functional. This change is
to trigger PHY operations in manager, instead of host, so that
host and PHY can be completely separated.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In case of dual DSI, some registers in PHY1 have been programmed
during PLL0 clock's set_rate. The PHY1 reset called by host1 later
will silently reset those PHY1 registers. This change is to reset
and enable both PHYs before any PLL clock operation.
[Originally worked on by Hai Li <hali@codeaurora.org>. Fixed up
by Archit Taneja <architt@codeaurora.org>]
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For some new types of DSI PHY, more settings depend on
use cases controlled by DSI manager. This change allows
DSI manager to setup PHY with a use case.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DSI host is required to configure more timings calculated
in PHY. By introducing a shared structure, this change allows
more timing information passed from PHY to host.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create an init() op for dsi_phy which sets up things specific to
a given DSI PHY.
The dsi_phy driver probe expects every DSI version to get a
"dsi_phy_regulator" mmio base. This isn't the case for 8x96.
Creating an init() op will allow us to accommodate such
differences.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add 8x96 DSI data in dsi_cfg. The downstream kernel's dsi_host driver
enables core_mmss_clk. We're seeing some branch clock warnings on
8x96 when enabling this. There doesn't seem to be any negative effect
with not enabling this clock, so use it once we figure out why we
get the warnings.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The driver returns an error if a DSI DT node is populated, but no device
is connected to it or if the data-lane map isn't present. Ideally, such
a DSI node shouldn't be probed at all (i.e, its status should be set to
"disabled in DT"), but there isn't any harm in registering the DSI device
even if it doesn't have a bridge/panel connected to it.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The mdp5 kms driver currently sets up multiple encoders per interface
(INTF), one for each kind of mode of operation it supports.
We create 2 drm_encoders for DSI, one for Video Mode and the other
for Command Mode operation. The reason behind this approach could have
been that we aren't aware of the DSI device's mode of operation when
we create the encoders.
This makes things a bit complicated, since these encoders have to
be further attached to the same DSI bridge. The easier way out is
to create a single encoder, and make the DSI driver set its mode
of operation when we know what the DSI device's mode flags are.
Start with providing a way to set the mdp5_intf_mode using a kms
func that sets the encoder's mode of operation. When constructing
a DSI encoder, we set the mode of operation to Video Mode as
default. When the DSI device is attached to the host, we probe the
DSI mode flags and set the corresponding mode of operation.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently create 2 encoders for DSI interfaces, one for command
mode and other for video mode operation. This isn't needed as we
can't really use both the encoders at the same time. It also makes
connecting bridges harder.
Switch to creating a single encoder. For now, we assume that the
encoder is configured only in video mode. Later, the same encoder
would be usable in both modes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The commit "drm: bridge: Link encoder and bridge in core code" updated
the drm_bridge_attach() API to also include the drm_encoder pointer
the bridge attaches to.
The func msm_dsi_manager_bridge_init() now relies on the drm_encoder
pointer stored in msm_dsi->encoders to pass the encoder to the bridge
API.
msm_dsi->encoders is unfortunately set after this function is called,
resulting in us passing a NULL pointer to drm_brigde_attach. This
results in an error and the DSI driver probe fails.
Move the initialization of msm_dsi->encoders[] a bit up. Also, don't
try to set the encoder's bridge. That's now managed by the bridge
API.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Instead of linking encoders and bridges in every driver (and getting it
wrong half of the time, as many drivers forget to set the drm_bridge
encoder pointer), do so in core code. The drm_bridge_attach() function
needs the encoder and optional previous bridge to perform that task,
update all the callers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Stefan Agner <stefan@agner.ch> # For DCU
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # For atmel-hlcdc
Acked-by: Vincent Abriou <vincent.abriou@st.com> # For STI
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # For sun4i
Acked-by: Xinliang Liu <z.liuxinliang@hisilicon.com> # For hisilicon
Acked-by: Jyri Sarha <jsarha@ti.com> # For tilcdc
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1481709550-29226-4-git-send-email-laurent.pinchart+renesas@ideasonboard.com
On the userspace side, all the basics are working, and most of glmark2
is working. I've been working through deqp, and I've got a couple more
things to fix (but we've gone from 70% to 80+% pass in last day, and
current deqp run that is going should pick up another 5-10%). I expect
to push the mesa patches today or tomorrow.
There are a couple more a5xx related patches to take the gpu out of
secure mode (for the devices that come up in secure mode, like the hw
I have), but those depend on an scm patch that would come in through
another tree. If that can land in the next day or two, there might
be a second late pull request for drm/msm.
In addition to the new-shiny, there have also been a lot of overlay/
plane related fixes for issues found using drm-hwc2 (in the process of
testing/debugging the atomic/kms fence patches), resulting in rework
to assign hwpipes to kms planes dynamically (as part of global atomic
state) and also handling SMP (fifo) block allocation atomically as
part of the ->atomic_check() step. All those patches should also help
out atomic weston (when those patches eventually land).
* 'msm-next' of git://people.freedesktop.org/~robclark/linux: (36 commits)
drm/msm: gpu: Add support for the GPMU
drm/msm: gpu: Add A5XX target support
drm/msm: Disable interrupts during init
drm/msm: Remove 'src_clk' from adreno configuration
drm/msm: gpu: Add OUT_TYPE4 and OUT_TYPE7
drm/msm: Add adreno_gpu_write64()
drm/msm: gpu Add new gpu register read/write functions
drm/msm: gpu: Return error on hw_init failure
drm/msm: gpu: Cut down the list of "generic" registers to the ones we use
drm/msm: update generated headers
drm/msm/adreno: move scratch register dumping to per-gen code
drm/msm/rd: support for 64b iova
drm/msm: convert iova to 64b
drm/msm: set dma_mask properly
drm/msm: Remove bad calls to of_node_put()
drm/msm/mdp5: move LM bounds check into plane->atomic_check()
drm/msm/mdp5: dump smp state on errors too
drm/msm/mdp5: add debugfs to show smp block status
drm/msm/mdp5: handle SMP block allocations "atomically"
drm/msm/mdp5: dynamically assign hw pipes to planes
...
For a5xx the gpu is 64b so we need to change iova to 64b everywhere. On
the display side, iova is still 32b so it can ignore the upper bits.
(Although all the armv8 devices have an iommu that can map 64b pa to 32b
iova.)
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DSI/HDMI PLLs in MSM require resources like interface clocks, power
domains to be enabled before we can access their registers.
The clock framework doesn't have a mechanism at the moment where we can
tie such resources to a clock, so we make sure that the KMS driver enables
these resources whenever a PLL is expected to be in use.
One place where we can't ensure the resource dependencies are met is when
the clock framework tries to disable unused clocks. The KMS driver doesn't
know when the clock framework calls the is_enabled clk_op, and hence can't
enable interface clocks/power domains beforehand.
We set the CLK_IGNORE_UNUSED flag for PLL clocks for now. This needs to be
revisited, since bootloaders can enable display, and we would want to
disable the PLL clocks if there isn't a display driver using them.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The msm/dsi host drivers calls drm_helper_hpd_irq_event in the
mipi_dsi_host attach/detatch callbacks.
mipi_dsi_attach()/mipi_dsi_detach() from a panel/bridge
driver could be called from a context where the drm_device's
mode_config.mutex is already held, resulting in a deadlock.
Queue it as work instead.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In case of error, the function drm_mode_duplicate() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Before we can add vmap shrinking, we really need to know which vmap'ings
are currently being used. So switch to get/put interface. Stubbed put
fxns for now.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DSI host and PHY driver currently expects the DT bindings to provide
custom properties "qcom,dsi-host-index" and "qcom,dsi-phy-index" so that
the driver can identify which DSI instance it is.
The binding isn't acceptable, but the driver still needs to figure out
what its instance id. This is now done by storing the mmio starting
addresses for each DSI instance in every SoC version in the driver. The
driver then identifies the index number by trying to match the stored
address with comparing the resource start address we get from DT.
We don't have compatible strings for DSI PHY on each SoC, but only the
DSI PHY type. We only support one SoC version for each PHY type, so we
get away doing the same thing above for the PHY driver. We can revisit
this when we support two SoCs with the same DSI PHY.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
A more standard DT binding describing data lanes already exists here:
Documentation/devicetree/bindings/media/video-interfaces.txt
Use this binding instead of "qcom,data-lane-map". One difference
in the standard binding w.r.t to the existing binding is that it
provides a logical to physical mapping instead of the other way
round. Tweak the code to translate the data the way we want it.
The MSM DSI DT bindings aren't used anywhere at the moment, so
it's okay to update this property.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DSI host links to the DSI PHY device using a custom binding. Switch to
the generic PHY bindings. The DSI PHY driver itself doesn't use the common
PHY framework for now.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DSI interface is going to have two ports defined in its device node.
The first port is always going to be the link between the MDP output
and the input to DSI, the second port is going to be the link between
the DSI output and the connected panel/bridge:
----- ----- -------
| MDP | ------> | DSI | ------> | Panel |
----- ----- -------
(Port 0) (Port 1)
Until now, there was only one Port representing the output. Update the
DSI host driver such that it parses Port #1 for a connected device.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Move the drm_connector registration from the encoder(HDMI/DSI etc) drivers
to the msm platform driver. This will simplify the task of ensuring that
the connectors are registered only after the drm_device itself is
registered.
The connectors' destroy ops are made to use kzalloc instead of
devm_kzalloc to ensure that that the connectors can be successfully
unregistered when the msm driver module is removed. The memory for the
connectors is unallocated when drm_mode_config_cleanup() is called
during either during an error or during driver remove.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The voltage changing code in this driver is broken and should be
removed. The driver sets a single, exact voltage on probe. Unless
there is a very good reason for this (which should be documented in
comments) constraints like this need to be set via the machine
constraints, voltage setting in a driver is expected to be used in cases
where the voltage varies at runtime.
In addition client drivers should almost never be calling
regulator_can_set_voltage(), if the device needs to set a voltage it
needs to set the voltage and the regulator core will handle the case
where the regulator is fixed voltage. If the driver simply skips
setting the voltage if it doesn't have permission then it should just
not bother in the first place.
Originally authored by Mark Brown <broonie@kernel.org>
Remove the min/max voltage data entries per SoC managed by the driver.
These aren't needed as we don't try to set voltages any more. Mention in
comments the voltages that each regulator expects.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This fixes the following build failure:
drivers/gpu/drm/msm/dsi/pll/dsi_pll_28nm.o: In function `msm_dsi_pll_28nm_8960_init':
dsi_pll_28nm.c:(.text+0x1198): multiple definition of `msm_dsi_pll_28nm_8960_init'
drivers/gpu/drm/msm/dsi/pll/dsi_pll.o:dsi_pll.c:(.text+0x0): first defined here
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Acked-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DSI driver is currently unaware of how the DSI physical data lanes
are mapped to the logical lanes provided by the DSI controller.
Create a DT binding "qcom,data-lane-map" that provides this information
on a given platform.
The MSM DSI controller is restricted in terms of what all mappings
it can support. The lane polarity is fixed for all the lanes, the clock
lanes are fixed, and the data lanes can be swapped among each other only
for a few combinations. Apply these restrictions when we parse the DT
data.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
VDD regulator input was specified for MSM8916. It turns our that this
regulator is used for the display panels used on MSM8916 platforms, but
not the DSI controller itself. Drop this regulator from the list.
Reported-by: Vinay Simha <vinaysimha@inforcecomputing.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
With the implementation of of_graph parsing, it isn't any longer
necessary for msm_host->device node to be same as dsi->dev.of_node. This
only holds true when the connected device is also a child of the dsi_host.
In the case of external bridge chips belonging to a different control
bus, these are guaranteed to be different.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
in case of failed to get iova, function was returning without releasing
the mutex. Added it.
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For DSIv2 to work, we need to enable MMSS_AHB_ARB_MASTER_PORT in
MMSS_SFPB. We enable the required bitfield by retrieving MMSS_SFPB
regmap pointer via syscon.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently use iommu allocated DMA buffers for sending DSI commands.
DSIv2 doesn't have a port connected to the MDP iommu. Therefore, it
can't use iommu allocated buffers to fetch DSI commands.
Use a regular contiguous DMA buffer if we are DSIv2.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add a dsi_cfg entry for APQ8064. Since this is the first DSIv2 chip to
be supported, add a list of bus clocks that are required by the DSIv2
block.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSIv2 (DSI on older A family chips) has slightly different link clock
requirements.
First, we have an extra clock called src_clk (with a dedicated RCG).
This is required by the DSI controller to process the pixel data
coming from MDP. It needs to be set at the rate "pclk * bytes_per_pixel".
We also need to explicitly configure esc_clk. On DSI6G chips, we don't
need to set a rate to esc_clk because its RCG is always sourced from
crystal clock (19.2 Mhz in all cases), which is within the escape clock
frequency range in the mipi DSI spec. For chips with DSIv2, the crystal
clock rate may not be within the required range (27Mhz on APQ8064).
Therefore, we derive it from the DSI byte clock. We calculate an esc_clck
rate that is within the mipi spec and also divisible by the byte clock
rate.
When setting rate and enabling the link clocks, we make sure that byte_clk
is configured before esc_clk, and src_clk before pixel_clk. We create two
different link_enable funcs for DSI6G and DSIv2 since the sequences are
different.
We also obtain two extra source clocks (dsi_src_clk and esc_src_clk) and
set their parent to the clocks provided by DSI PLL.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI bus clocks seem to vary between different DSI host versions, and the
SOC to which they belong. Even the enable/disable sequence varies.
Provide a list of bus clock names in dsi_cfg. The driver will use this to
retrieve the clocks, and enable/disable them.
Add bus clock lists for DSI6G, and DSI for MSM8916(this is DSI6G too, but
there is no MMSS_CC specific clock since there is no MMSS clock controller
on 8916).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Initialize clocks only after we get the DSI host version. This will allow
us to get clocks using a pre-defined list based on the DSI major/minor
version of the host. This is required since clock requirements of
different major DSI revisions(v2 vs 6g) aren't the same.
Modify dsi_get_version to get the interface clock, and then put it after
it is used.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The current version checking mechanism works fine for DSI6G blocks. It
doesn't work so well for older generation DSIv2 blocks.
The initial read of REG_DSI_6G_HW_VERSION(offset 0x0) would result in a
read of REG_DSI_CTRL for DSIv2. This register won't necessarily be 0 on
DSIv2. It can be non zero if DSI was previously initialized by the
bootloader.
Instead of reading offset 0x0, we now read offset 0x1f0. For DSIv2, this
register is DSI_VERSION, and is bound to be non-zero. On DSI6G, this
register(offset 0x1f0) is SCRATCH_REGISTER_0, which no one ever seems to
touch, and from all register dumps I'vc seen, holds 0 all the time.
Modify dsi_get_version to read REG_DSI_VERSION to determine whether we
are DSI6G or DSIv2.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add DSI PLL common clock framework clocks for 8960 PHY.
The PLL here is different from the ones found in B family msm chips. As
before, the DSI provides two clocks to the outside world. dsixpll and
dsixpllbyte (x = 1, 2). dsixpll is a regular clock divider, but
dsixpllbyte is modelled as a custom clock divider.
dsixpllbyte is the starting point of the PLL configuration. It is the
one that sets up the VCO clock rate. We need the VCO clock rate in the
form: F * byteclk, where F is a multiplication factor that varies on
the byte clock the DSI driver is trying to set. We use the custom
clk_ops for dsixpllbyte to ensure that the parent (VCO) is set at this
rate.
An additional divider (POSTDIV1) generates the bitclk. Since bit clock
can be derived from byteclock, we calculate it internally, and don't
expose it as a clock.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI PHY on MSM8960 and APQ8064 is a 28nm PHY that's different from the
supported 28nm LP PHY found in newer chips.
Add support for the new PHY.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We retrieve the byte and pixel source clocks (RCG clocks) in the dsi
driver via DT. These are needed so that we can re-parent these source
clocks if we want to drive it using a different DSI PLL.
We shouldn't get these via DT because they aren't clocks that directly
serve as inputs to the dsi host.
Fortunately, there is a static parent-child link between the
byte_clk_src/pixel_clk_src and byte_clk/pixel_clk clocks. So, we can
retrieve the source clocks via clk_get_parent.
Do this instead of retrieving via DT.
Cc: Rob Herring <robh@kernel.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The current settings for 28nm PHY data lane CFG4 registers do
not work with certain panels. This change is to modify them to
hw recommended values.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In some configurations the supplies are voltage switches and not LDOs,
making the set voltage call to fail. Check with the regulator framework
if the supply can change voltage before attempting.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm for 4.3. Nouveau is
probably the biggest amount of changes in here, since it missed 4.2.
Highlights below, along with the usual bunch of fixes.
All stuff outside drm should have applicable acks.
Highlights:
- new drivers:
freescale dcu kms driver
- core:
more atomic fixes
disable some dri1 interfaces on kms drivers
drop fb panic handling, this was just getting more broken, as more locking was required.
new core fbdev Kconfig support - instead of each driver enable/disabling it
struct_mutex cleanups
- panel:
more new panels
cleanup Kconfig
- i915:
Skylake support enabled by default
legacy modesetting using atomic infrastructure
Skylake fixes
GEN9 workarounds
- amdgpu:
Fiji support
CGS support for amdgpu
Initial GPU scheduler - off by default
Lots of bug fixes and optimisations.
- radeon:
DP fixes
misc fixes
- amdkfd:
Add Carrizo support for amdkfd using amdgpu.
- nouveau:
long pending cleanup to complete driver,
fully bisectable which makes it larger,
perfmon work
more reclocking improvements
maxwell displayport fixes
- vmwgfx:
new DX device support, supports OpenGL 3.3
screen targets support
- mgag200:
G200eW support
G200e new revision support
- msm:
dragonboard 410c support, msm8x94 support, msm8x74v1 support
yuv format support
dma plane support
mdp5 rotation
initial hdcp
- sti:
atomic support
- exynos:
lots of cleanups
atomic modesetting/pageflipping support
render node support
- tegra:
tegra210 support (dc, dsi, dp/hdmi)
dpms with atomic modesetting support
- atmel:
support for 3 more atmel SoCs
new input formats, PRIME support.
- dwhdmi:
preparing to add audio support
- rockchip:
yuv plane support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1369 commits)
drm/amdgpu: rename gmc_v8_0_init_compute_vmid
drm/amdgpu: fix vce3 instance handling
drm/amdgpu: remove ib test for the second VCE Ring
drm/amdgpu: properly enable VM fault interrupts
drm/amdgpu: fix warning in scheduler
drm/amdgpu: fix buffer placement under memory pressure
drm/amdgpu/cz: fix cz_dpm_update_low_memory_pstate logic
drm/amdgpu: fix typo in dce11 watermark setup
drm/amdgpu: fix typo in dce10 watermark setup
drm/amdgpu: use top down allocation for non-CPU accessible vram
drm/amdgpu: be explicit about cpu vram access for driver BOs (v2)
drm/amdgpu: set MEC doorbell range for Fiji
drm/amdgpu: implement burst NOP for SDMA
drm/amdgpu: add insert_nop ring func and default implementation
drm/amdgpu: add amdgpu_get_sdma_instance helper function
drm/amdgpu: add AMDGPU_MAX_SDMA_INSTANCES
drm/amdgpu: add burst_nop flag for sdma
drm/amdgpu: add count field for the SDMA NOP packet v2
drm/amdgpu: use PT for VM sync on unmap
drm/amdgpu: make wait_event uninterruptible in push_job
...
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Cc: Wentao Xu <wentaox@codeaurora.org>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
With more platforms supported, the DSI host
configuration array keeps expanding. This change
moves those to a separate dsi_cfg module.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
On a certain platform, only one type of DSI PHY is used.
This change allows the user to only compile the PHY type
which is being used.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change moves each PHY type specific code into
separate files.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We are not checking the return value from msm_dsi_phy_disable().
Change the return type to void.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The bit position to configure source PLL will change
on new types of PHYs. The caller should pass down
this information.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The dsi bridge ops call drm_panel functions to set up the connected
drm_panel. Add checks to make sure these aren't called when we're
connected to an external bridge.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are platforms where the DSI output can be connected to another
encoder bridge chip (DSI to HDMI, DSI to LVDS etc).
Add support for external bridge support to the dsi driver. We assume that
the external bridge chip would be of the type drm_bridge. The dsi driver's
internal drm_bridge (msm_dsi->bridge) is linked to the external bridge's
drm_bridge struct.
In the case we're connected to an external bridge, we don't need to create
and manage a connector within our driver, it's the bridge driver's
responsibility to create one.
v2:
- Move the external bridge attaching stuff to dsi manager to make things
cleaner.
- Force the bridge to connect to a video mode encoder for now (the dsi
mode flags may have not been populated by modeset_init)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create a helper msm_dsi_device_connected() which checks whether we have a
device connected to the dsi host or not. This check gets messy when we
have support external bridges too. Having an inline function makes it
more legible.
For now, the check only consists of msm_dsi->panel being non-NULL. Later,
this will check if we have an external bridge or not.
This helper isn't used in dsi_connector related code as that's specific
to only when a drm_panel is connected.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently support only panels connected to dsi output. We're going to
also support external bridge chips now.
Change 'panel_node' to 'device_node' in the struct msm_dsi_host and
'panel_flags' to 'device_flags' in msm_dsi. This makes things sound a
bit more generic.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Platforms containing only DSI video mode devices don't need a TE gpio.
Make TE gpio optional.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The dsi host looks for the connected panel node by parsing for a child
named 'panel'. This hierarchy isn't very flexible. The connected
panel is forced to be a child to the dsi host, and hence, a mipi dsi
device. This isn't suitable for dsi devices that don't use mipi dsi
as their control bus.
Follow the of_graph approach of creating ports and endpoints to
represent the connections between the dsi host and the panel connected
to it. In our case, the dsi host will only have one output port, linked
to the panel's input port.
Update DT binding documentation with device graph usage info.
v3:
- Fix return value checks of of_graph_* calls.
- Don't make port a mandatory DT property
- Fix defer check when no panel node specified
- Rename parse_dt func to align with other dsi_host funcs
Reviewed-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Sean Paul