Multiple users have reported device initialization failure due the driver
not receiving legacy PCI interrupts. This is not unique to any particular
controller, but has been observed on multiple platforms.
There have been no issues reported or observed when with message signaled
interrupts, so this patch attempts to use MSI-x during initialization,
falling back to MSI. If that fails, legacy would become the default.
The setup_io_queues error handling had to change as a result: the admin
queue's msix_entry used to be initialized to the legacy IRQ. The case
where nr_io_queues is 0 would fail request_irq when setting up the admin
queue's interrupt since re-enabling MSI-x fails with 0 vectors, leaving
the admin queue's msix_entry invalid. Instead, return success immediately.
Reported-by: Tim Muhlemmer <muhlemmer@gmail.com>
Reported-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This fixes a scenario where device is present and being reset, but a
request to unbind the driver occurs.
A previous patch series addressing a device failure removal scenario
flushed reset_work after controller disable to unblock reset_work waiting
on a completion that wouldn't occur. This isn't safe as-is. The broken
scenario can potentially be induced with:
modprobe nvme && modprobe -r nvme
To fix, the reset work is flushed immediately after setting the controller
removing flag, and any subsequent reset will not proceed with controller
initialization if the flag is set.
The controller status must be polled while active, so the watchdog timer
is also left active until the controller is disabled to cleanup requests
that may be stuck during namespace removal.
[Fixes: ff23a2a15a]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Make sure the CQE phase (validity) is read before the rest of the
structure. The phase bit is the highest address and the CQE
read will happen on most platforms from lower to upper addresses
and will be done by multiple non-atomic loads. If the structure
is updated by PCI during the reads from the processor, the
processor may get a corrupted copy.
The addition of the new nvme_cqe_valid function that verifies
the validity bit also allows refactoring of the other CQE read
sequences.
Signed-off-by: Marta Rybczynska <marta.rybczynska@kalray.eu>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
PPAs sent to device is separately acknowledge in a 64bit status
variable. The status is stored in DW0 and DW1 of the completion queue
entry. Store this status inside the nvm_rq for further processing.
This can later be used to implement retry techniques for failed writes
and reads.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block driver updates from Jens Axboe:
"This is the block driver pull request for this merge window. It sits
on top of for-4.6/core, that was just sent out.
This contains:
- A set of fixes for lightnvm. One from Alan, fixing an overflow,
and the rest from the usual suspects, Javier and Matias.
- A set of fixes for nbd from Markus and Dan, and a fixup from Arnd
for correct usage of the signed 64-bit divider.
- A set of bug fixes for the Micron mtip32xx, from Asai.
- A fix for the brd discard handling from Bart.
- Update the maintainers entry for cciss, since that hardware has
transferred ownership.
- Three bug fixes for bcache from Eric Wheeler.
- Set of fixes for xen-blk{back,front} from Jan and Konrad.
- Removal of the cpqarray driver. It has been disabled in Kconfig
since 2013, and we were initially scheduled to remove it in 3.15.
- Various updates and fixes for NVMe, with the most important being:
- Removal of the per-device NVMe thread, replacing that with a
watchdog timer instead. From Christoph.
- Exposing the namespace WWID through sysfs, from Keith.
- Set of cleanups from Ming Lin.
- Logging the controller device name instead of the underlying
PCI device name, from Sagi.
- And a bunch of fixes and optimizations from the usual suspects
in this area"
* 'for-4.6/drivers' of git://git.kernel.dk/linux-block: (49 commits)
NVMe: Expose ns wwid through single sysfs entry
drivers:block: cpqarray clean up
brd: Fix discard request processing
cpqarray: remove it from the kernel
cciss: update MAINTAINERS
NVMe: Remove unused sq_head read in completion path
bcache: fix cache_set_flush() NULL pointer dereference on OOM
bcache: cleaned up error handling around register_cache()
bcache: fix race of writeback thread starting before complete initialization
NVMe: Create discard zero quirk white list
nbd: use correct div_s64 helper
mtip32xx: remove unneeded variable in mtip_cmd_timeout()
lightnvm: generalize rrpc ppa calculations
lightnvm: remove struct nvm_dev->total_blocks
lightnvm: rename ->nr_pages to ->nr_sects
lightnvm: update closed list outside of intr context
xen/blback: Fit the important information of the thread in 17 characters
lightnvm: fold get bb tbl when using dual/quad plane mode
lightnvm: fix up nonsensical configure overrun checking
xen-blkback: advertise indirect segment support earlier
...
The method to uniquely identify a namespace depends on the controller's
specification revision level and implemented capabilities. This patch
has the driver figure this out and exports the unique string through a
single 'wwid' attribute so the user doesn't have this burden.
The longest namespace unique identifier is used if available. If not
available, the driver will concat the controller's vendor, serial,
and model with the namespace ID. The specification provides this as a
unique indentifier.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The NVMe specification does not require discarded blocks return zeroes on
read, but provides that behavior as a possibility. Some applications more
efficiently use an SSD if reads on discarded blocks were deterministically
zero, based on the "discard_zeroes_data" queue attribute.
There is no specification defined way to determine device behavior on
discarded blocks, so the driver always left the queue setting disabled. We
can only know behavior based on individual device models, so this patch
adds a flag to the NVMe "quirk" list that vendors may set if they know
their controller works that way. The patch also sets the new flag for one
such known device.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Suggested-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When the media manager runs in dual or quad plane mode, lightnvm
abstracts away plane specific commands. This poses a problem for
get bad block table, as it reports bad blocks per plane, making the
table either two or four times bigger than expected. Fold the bad block
list before returning.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The block layer uses an unsigned short for max_segments. The way we
calculate the value for NVMe tends to generate very large 32-bit values,
which after integer truncation may lead to a zero value instead of
the desired outcome.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Jeff Lien <Jeff.Lien@hgst.com>
Tested-by: Jeff Lien <Jeff.Lien@hgst.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Factor out a helper to set all the device specific queue limits and apply
them to the admin queue in addition to the I/O queues. Without this the
command size on the admin queue is arbitrarily low, and the missing
other limitations are just minefields waiting for victims.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Jeff Lien <Jeff.Lien@hgst.com>
Tested-by: Jeff Lien <Jeff.Lien@hgst.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
A user could send a passthrough IO command with a metadata pointer to a
namespace without metadata. With metadata length of 0, kmalloc returns
ZERO_SIZE_PTR. Since that is not NULL, the driver would have set this as
the bio's integrity payload, which causes an access fault on completion.
This patch ignores the users metadata buffer if the namespace format
does not support separate metadata.
Reported-by: Stephen Bates <stephen.bates@microsemi.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The command flags can change the meaning of other fields in the command
that the driver is not prepared to handle. Specifically, the user could
passthrough an SGL flag, causing the controller to misinterpret the PRP
list the driver created, potentially corrupting memory or data.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This moves failed queue handling out of the namespace removal path and
into the reset failure path, fixing a hanging condition if the controller
fails or link down during del_gendisk. Previously the driver had to see
the controller as degraded prior to calling del_gendisk to setup the
queues to fail. But, if the controller happened to fail after this,
there was no task to end outstanding requests.
On failure, all namespace states are set to dead. This has capacity
revalidate to 0, and ends all new requests with error status.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
A reset failure schedules the device to unbind from the driver through
the pci driver's remove. This cleans up all intialization, so there is
no need to duplicate the potentially racy cleanup.
To help understand why a reset failed, the status is logged with the
existing warning message.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch makes nvme namespace removal lockless. It is up to the caller
to ensure no active namespace scanning is occuring. To ensure no scan
work occurs, the nvme pci driver adds a removing state to the controller
device to avoid queueing scan work during removal. The work is flushed
after setting the state, so no new scan work can be queued.
The lockless removal allows the driver to cleanup a namespace
request_queue if the controller fails during removal. Previously this
could deadlock trying to acquire the namespace mutex in order to handle
such events.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
A namespace may be detached from a controller, but a user may be holding
a reference to it. Attaching a new namespace with the same NSID will create
duplicate names when using the NSID to name the disk.
This patch uses an IDA that is released only when the last reference is
released instead of using the namespace ID.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Unmapping the registers on reset or shutdown is not necessary. Keeping
the mapping simplifies reset handling.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
For NVMe over Fabrics, the cntlid will be used by systemd/udev to
create link to the device, for example,
/dev/disk/by-path/<fabrics-info>-<cntlid>-<namespace> -> /dev/nvme0n1
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Both LighNVM and NVMe over Fabrics need to look at more than just the
status and result field.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Matias Bj?rling <m@bjorling.me>
Reviewed-by: Jay Freyensee <james.p.freyensee@intel.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The only work left in the kthread is the periodic health check for each
controller. There is no need to run this from process context or keep
a thread context around for it, so replace it with a simpler timer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
There is no reason to do unconditional polling of CQs per the NVMe
spec.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Use a dedicated work item to submit async event requests instead of the
global kthread. This simplifies the code and reduces the latencies to
resubmit a request once an even notification happened.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
We don't need to spam the kernel logs with thousands of IO cancelling
messages. We can infer all IO's are being cancelled with fewer, or
even none at all. This patch rate limits the message and uses the debug
log level as it is mainly used for testing purposes.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
A device failure or link down wouldn't have been detected during namespace
removal. This patch keeps the device in the list for polling so that the
thread may see such failure and initiate a reset. The device is removed
from the list after disable, so we can safely flush the reset work as
it can't be requeued when disable completes.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It's possible a request may get to the driver after the nvme queue was
disabled. This has the request requeue if that happens.
Note the request is still "started" by the driver, but requeuing will
clear the start state for timeout handling.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It is generally more efficient to submit larger IO.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The function returns true when the controller can't handle IO.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
NVMe over Fabrics drivers are going to reuse the core,
so splits nvme.ko into 2 modules:
nvme-core.ko: the core part
nvme.ko: the PCI driver
Export symbols from nvme-core.ko.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Split dev_list_lock into one in the core and one in the PCI driver.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
These variables are used by PCI driver and will also be used in the
forthcoming NVMe over Fabrics drivers.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We don't want to be able to unload the fabric driver when we have
openened referenced to our namespaces. Thus, for each nvme_open we
take a reference on the fabric driver and put it in nvme_release.
This behavior is consistent with the scsi model.
This resolves the panic when unloading a fabric module with
mpath holders.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ian Bakshan <ianb@mellanox.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Having the ctrl name "nvmeX" seems much more friendly than
the underlying device name. Also, with other nvme transports
such as the soon to come nvme-loop we don't have an underlying
device so it doesn't makes sense to make up one.
In order to help matching an instance name to a pci function,
we add a info print in nvme_probe.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Manually fixed up the hunk in nvme_cancel_queue_ios().
Signed-off-by: Jens Axboe <axboe@fb.com>
Pass the right private data to device_create_with_groups from the
beginning, and remove the superflous call to dev_set_drvdata.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This notifies blk-mq when the tag set contains a different number of
queues prior to freeing unused ones that the request queue points to.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The specification currently limits the number of MLC pairs to 886. Make
sure that a device is unable to be instantiate if more is configured.
Also, previously the patch had the wrong math for copying MLC pairs, as
it only copied half of the actual entries.
Fixes: ca5927e7ab "lightnvm: introduce mlc lower page table mappings"
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull NVMe updates from Jens Axboe:
"Last branch for this series is the nvme changes. It's in a separate
branch to avoid splitting too much between core and NVMe changes,
since NVMe is still helping drive some blk-mq changes. That said, not
a huge amount of core changes in here. The grunt of the work is the
continued split of the code"
* 'for-4.5/nvme' of git://git.kernel.dk/linux-block: (67 commits)
uapi: update install list after nvme.h rename
NVMe: Export NVMe attributes to sysfs group
NVMe: Shutdown controller only for power-off
NVMe: IO queue deletion re-write
NVMe: Remove queue freezing on resets
NVMe: Use a retryable error code on reset
NVMe: Fix admin queue ring wrap
nvme: make SG_IO support optional
nvme: fixes for NVME_IOCTL_IO_CMD on the char device
nvme: synchronize access to ctrl->namespaces
nvme: Move nvme_freeze/unfreeze_queues to nvme core
PCI/AER: include header file
NVMe: Export namespace attributes to sysfs
NVMe: Add pci error handlers
block: remove REQ_NO_TIMEOUT flag
nvme: merge iod and cmd_info
nvme: meta_sg doesn't have to be an array
nvme: properly free resources for cancelled command
nvme: simplify completion handling
nvme: special case AEN requests
...
Pull lightnvm fixes and updates from Jens Axboe:
"This should have been part of the drivers branch, but it arrived a bit
late and wasn't based on the official core block driver branch. So
they got a small scolding, but got a pass since it's still new. Hence
it's in a separate branch.
This is mostly pure fixes, contained to lightnvm/, and minor feature
additions"
* 'for-4.5/lightnvm' of git://git.kernel.dk/linux-block: (26 commits)
lightnvm: ensure that nvm_dev_ops can be used without CONFIG_NVM
lightnvm: introduce factory reset
lightnvm: use system block for mm initialization
lightnvm: introduce ioctl to initialize device
lightnvm: core on-disk initialization
lightnvm: introduce mlc lower page table mappings
lightnvm: add mccap support
lightnvm: manage open and closed blocks separately
lightnvm: fix missing grown bad block type
lightnvm: reference rrpc lun in rrpc block
lightnvm: introduce nvm_submit_ppa
lightnvm: move rq->error to nvm_rq->error
lightnvm: support multiple ppas in nvm_erase_ppa
lightnvm: move the pages per block check out of the loop
lightnvm: sectors first in ppa list
lightnvm: fix locking and mempool in rrpc_lun_gc
lightnvm: put block back to gc list on its reclaim fail
lightnvm: check bi_error in gc
lightnvm: return the get_bb_tbl return value
lightnvm: refactor end_io functions for sync
...
Pull core block updates from Jens Axboe:
"We don't have a lot of core changes this time around, it's mostly in
drivers, which will come in a subsequent pull.
The cores changes include:
- blk-mq
- Prep patch from Christoph, changing blk_mq_alloc_request() to
take flags instead of just using gfp_t for sleep/nosleep.
- Doc patch from me, clarifying the difference between legacy
and blk-mq for timer usage.
- Fixes from Raghavendra for memory-less numa nodes, and a reuse
of CPU masks.
- Cleanup from Geliang Tang, using offset_in_page() instead of open
coding it.
- From Ilya, rename request_queue slab to it reflects what it holds,
and a fix for proper use of bdgrab/put.
- A real fix for the split across stripe boundaries from Keith. We
yanked a broken version of this from 4.4-rc final, this one works.
- From Mike Krinkin, emit a trace message when we split.
- From Wei Tang, two small cleanups, not explicitly clearing memory
that is already cleared"
* 'for-4.5/core' of git://git.kernel.dk/linux-block:
block: use bd{grab,put}() instead of open-coding
block: split bios to max possible length
block: add call to split trace point
blk-mq: Avoid memoryless numa node encoded in hctx numa_node
blk-mq: Reuse hardware context cpumask for tags
blk-mq: add a flags parameter to blk_mq_alloc_request
Revert "blk-flush: Queue through IO scheduler when flush not required"
block: clarify blk_add_timer() use case for blk-mq
bio: use offset_in_page macro
block: do not initialise statics to 0 or NULL
block: do not initialise globals to 0 or NULL
block: rename request_queue slab cache
Adds all controller information to attribute list exposed to sysfs, and
appends the reset_controller attribute to it. The nvme device is created
with this attribute list, so driver no long manages its attributes.
Reported-by: Sujith Pandel <sujithpshankar@gmail.com>
Cc: Sujith Pandel <sujithpshankar@ gmail.com>
Cc: David Milburn <dmilburn@redhat.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We don't need to shutdown a controller for a reset. A controller in a
shutdown state may take longer to become ready than one that was simply
disabled. This patch has the driver shut down a controller only if the
device is about to be powered off or being removed. When taking the
controller down for a reset reason, the controller will be disabled
instead.
Function names have been updated in this patch to reflect their changed
semantics.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The nvme driver deletes IO queues asynchronously since this operation
may potentially take an undesirable amount of time with a large number
of queues if done serially.
The driver used to manage coordinating asynchronous deletions. This
patch simplifies that by leveraging the block layer rather than using
kthread workers and chaining more complicated callbacks.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
NVMe submits all commands through the block layer now. This means we
can let requests queue at the blk-mq hardware context since there is no
path that bypasses this anymore so we don't need to freeze the queues
anymore. The driver can simply stop the h/w queues from running during
a reset instead.
This also fixes a WARN in percpu_ref_reinit when the queue was unfrozen
with requeued requests.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
A negative status has the "do not retry" bit set, which makes it not
retryable. Use a fake status that can potentially be retried on reset.
An aborted command's status is overridden by the timeout handler so
that it won't be retried, which is necessary to keep initialization from
getting into a reset loop.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The tag set queue depth needs to be one less than the h/w queue depth
so we don't wrap the circular buffer. This conforms to the specification
defined "Full Queue" condition.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Translation SCSI commands to NVMe commands is rather pointless in general
as applications must not expext to be able to use SCSI commands on a
generic block device.
Make the huge translation layer optional and hope no one will ever enable
it in the future.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Make sure we synchronize access to the namespaces list and grab a reference
to the namespace before doing I/O. Make sure to reject the ioctl if multiple
namespaces are present as it's entirely unsafe, and warn when using it even
with a single namespace.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently traversal and modification of ctrl->namespaces happens completely
unsynchronized, which can be fixed by the addition of a simple mutex.
Note: nvme_dev_ioctl will be handled in the next patch.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Nothing pci specific about them and We'll need them exported
in other transports too.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Keith Busch