The patch add memory-mapped timer register support by using the
information provided by the new GTDT driver of ACPI.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
[Mark: verify CNTFRQ, only register the first frame]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
The patch update arm_arch_timer driver to use the function
provided by the new GTDT driver of ACPI.
By this way, arm_arch_timer.c can be simplified, and separate
all the ACPI GTDT knowledge from this timer driver.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Currently the code to probe MMIO architected timers mixes DT parsing with
actual poking of hardware. This makes the code harder than necessary to
understand, and makes it difficult to add support for probing via ACPI.
This patch splits the DT parsing from HW probing. The DT parsing now
lives in arch_timer_mem_of_init(), which fills in an arch_timer_mem
structure that it hands to probing functions that can be reused for ACPI
support.
Since the rate detection logic will be slight different when using ACPI,
the probing is performed as a number of steps. This results in more code
for the moment, and some arguably redundant work, but simplifies matters
considerably when ACPI support is added.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
[Mark: refactor the probing split]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
To cleanly split code paths specific to ACPI or DT at a higher level,
this patch removes arch_timer_init(), folding the relevant
parts of its logic into existing callers.
This pathes the way for further rework, and saves a few lines.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
[Mark: reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
When booting with DT, it's possible for timer nodes to be probed in any
order. Some common initialisation needs to occur after all nodes have
been probed, and arch_timer_common_init() has code to detect when this
has happened.
This logic is DT-specific, and it would be best to factor it out of the
common code that will be shared with ACPI.
This patch folds this into the existing arch_timer_needs_probing(),
which is renamed to arch_timer_needs_of_probing(), and no longer takes
any arguments. This is only called when using DT, and not when using
ACPI, which will have a deterministic probe order.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
[Mark: reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
For historical reasons, rate detection when probing via DT is somewhat
convoluted. We tried to package this up in arch_timer_detect_rate(), but
with the addition of ACPI worse, and gets in the way of stringent rate
checking when ACPI is used.
This patch makes arch_timer_detect_rate() specific to DT, ripping out
ACPI logic. In preparation for rework of the MMIO timer probing, the
reading of the relevant CNTFRQ register is factored out to callers. The
function is then renamed to arch_timer_of_configure_rate(), which better
represents its new place in the world.
Comments are added in the DT and ACPI probe paths to explain this.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
[Mark: reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Pull clockevents updates from Daniel Lezcano
- Provide a framework to handle errata gracefuly for arm_arch_timer (Mark
Zyngier)
- Clarify the DT properties for the rockchip timer and add the clocksource as
an alternative to the bogus architected timer (Alexander Kochetkov)
- Rename the Gemini timer to Faraday timer fttmr010 and provide a specific
initialization for Gemini (Linus Walleij)
- Add missing newlines in the error message in the timers (Rafał Miłecki)
- Read the clock once and implement the delay timer on Orion (Russell King)
In preparation for making the clockevents core NTP correction aware,
all clockevent device drivers must set ->min_delta_ticks and
->max_delta_ticks rather than ->min_delta_ns and ->max_delta_ns: a
clockevent device's rate is going to change dynamically and thus, the
ratio of ns to ticks ceases to stay invariant.
Make the timer-atlas7 clockevent driver initialize these fields properly.
This patch alone doesn't introduce any change in functionality as the
clockevents core still looks exclusively at the (untouched) ->min_delta_ns
and ->max_delta_ns. As soon as this has changed, a followup patch will
purge the initialization of ->min_delta_ns and ->max_delta_ns from this
driver.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Barry Song <baohua@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
In preparation for making the clockevents core NTP correction aware,
all clockevent device drivers must set ->min_delta_ticks and
->max_delta_ticks rather than ->min_delta_ns and ->max_delta_ns: a
clockevent device's rate is going to change dynamically and thus, the
ratio of ns to ticks ceases to stay invariant.
Make the sh_cmt clockevent driver initialize these fields properly.
This patch alone doesn't introduce any change in functionality as the
clockevents core still looks exclusively at the (untouched) ->min_delta_ns
and ->max_delta_ns. As soon as this has changed, a followup patch will
purge the initialization of ->min_delta_ns and ->max_delta_ns from this
driver.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
In preparation for making the clockevents core NTP correction aware,
all clockevent device drivers must set ->min_delta_ticks and
->max_delta_ticks rather than ->min_delta_ns and ->max_delta_ns: a
clockevent device's rate is going to change dynamically and thus, the
ratio of ns to ticks ceases to stay invariant.
Make the numachip clockevent driver initialize these fields properly.
This patch alone doesn't introduce any change in functionality as the
clockevents core still looks exclusively at the (untouched) ->min_delta_ns
and ->max_delta_ns. As soon as this has changed, a followup patch will
purge the initialization of ->min_delta_ns and ->max_delta_ns from this
driver.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
In preparation for making the clockevents core NTP correction aware,
all clockevent device drivers must set ->min_delta_ticks and
->max_delta_ticks rather than ->min_delta_ns and ->max_delta_ns: a
clockevent device's rate is going to change dynamically and thus, the
ratio of ns to ticks ceases to stay invariant.
Make the metag_generic clockevent driver initialize these fields properly.
This patch alone doesn't introduce any change in functionality as the
clockevents core still looks exclusively at the (untouched) ->min_delta_ns
and ->max_delta_ns. As soon as this has changed, a followup patch will
purge the initialization of ->min_delta_ns and ->max_delta_ns from this
driver.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
In preparation for making the clockevents core NTP correction aware,
all clockevent device drivers must set ->min_delta_ticks and
->max_delta_ticks rather than ->min_delta_ns and ->max_delta_ns: a
clockevent device's rate is going to change dynamically and thus, the
ratio of ns to ticks ceases to stay invariant.
Make the dw_apb clockevent driver initialize these fields properly.
This patch alone doesn't introduce any change in functionality as the
clockevents core still looks exclusively at the (untouched) ->min_delta_ns
and ->max_delta_ns. As soon as this has changed, a followup patch will
purge the initialization of ->min_delta_ns and ->max_delta_ns from this
driver.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Currently, the arch timer driver uses ARCH_TIMER_PHYS_SECURE_PPI to mean
the driver will use the secure PPI *and* potentially also use the
non-secure PPI. This is somewhat confusing.
For arm64 it never makes sense to use the secure PPI, but we do anyway,
inheriting this behaviour from 32-bit arm. For ACPI, we may not even
have a valid secure PPI, so we need to be able to only request the
non-secure PPI.
To that end, this patch reworks the timer driver so that we can request
the non-secure PPI alone. The PPI selection is split out into a new
function, arch_timer_select_ppi(), and verification of the selected PPI
is shifted out to callers (as DT may select the PPI by other means and
must handle this anyway).
We now consistently use arch_timer_has_nonsecure_ppi() to determine
whether we must manage a non-secure PPI *in addition* to a secure PPI.
When we only have a non-secure PPI, this returns false.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
[Mark: reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
This patch add a new enum "arch_timer_spi_nr" and use it in the driver.
Just for code's readability, no functional change.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
To support the arm_arch_timer via ACPI we need to share defines and enums
between the driver and the ACPI parser code.
So we split out the relevant defines and enums into arm_arch_timer.h.
No functional change.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
In preparation for moving the PPI enum out into a header, rename the
enum and its constituent values these so they are namespaced w.r.t. the
arch timer. This will aid consistency and avoid potential name clashes
when this move occurs.
No functional change.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
[Mark: reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
In preparation for moving the type macros out into a header, rename
these so they are namespaced w.r.t. the arch timer. We'll apply the same
prefix to other definitions in subsequent patches. This will aid
consistency and avoid potential name clahses when this move occurs.
No functional change.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
[Mark: reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Almost all string in the arm_arch_timer driver duplicate an common
prefix (though a few do not). For consistency, it would be better to use
pr_fmt(), and always use this prefix. At the same time, we may as well
clean up some whitespace issues in arch_timer_banner and
arch_timer_init.
No functional change.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
[Mark: reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
that will also go via the arm64 tree.
-----BEGIN PGP SIGNATURE-----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=WlYI
-----END PGP SIGNATURE-----
Merge tag 'arch-timer-errata' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into clockevents/4.12
arm64 arch timer workaround series, including the base patches
that will also go via the arm64 tree.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The plain Faraday FTTMR010 timer needs a clock to figure out its
tick rate, and the gemini reads it directly from the system
controller set-up. Split the init function and add two paths for
the two compatible-strings. We only support clocking using PCLK
because of lack of documentation on how EXTCLK works.
The Gemini still works like before, but we can also support a
generic, clock-based version.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
After some research it turns out that the "Gemini" timer is
actually a generic IP block from Faraday Technology named
FTTMR010, so as to not make things too confusing we need to
rename the driver and its symbols to make sense.
The implementation remains the same in this patch but we fix
the copy-paste error in the timer name "nomadik_mtu" as we're
at it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The clock supplying the arm-global-timer on the rk3188 is coming from the
the cpu clock itself and thus changes its rate everytime cpufreq adjusts
the cpu frequency making this timer unsuitable as a stable clocksource
and sched clock.
The rk3188, rk3288 and following socs share a separate timer block already
handled by the rockchip-timer driver. Therefore adapt this driver to also
be able to act as clocksource and sched clock on rk3188.
In order to test clocksource you can run following commands and check
how much time it take in real. On rk3188 it take about ~45 seconds.
cpufreq-set -f 1.6GHZ
date; sleep 60; date
In order to use the patch you need to declare two timers in the dts
file. The first timer will be initialized as clockevent provider
and the second one as clocksource. The clockevent must be from
alive subsystem as it used as backup for the local timers at sleep
time.
The patch does not break compatibility with older device tree files.
The older device tree files contain only one timer. The timer
will be initialized as clockevent, as expected.
rk3288 (and probably anything newer) is irrelevant to this patch,
as it has the arch timer interface. This patch may be useful
for Cortex-A9/A5 based parts.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add an implementation for the ARM delay timer, which is used for
udelay(). This provides less CPU dependent and more accurate delays -
the CPU loop on Marvell Dove appears to calibrate to around 6% too
short.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Rather than reading the clock rate three times, read it once - we are
about to add a fourth usage.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In order to deal with ACPI enabled platforms suffering from the
HISILICON_ERRATUM_161010101, let's add the required OEM data that
allow the workaround to be enabled.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: dann frazier <dann.frazier@canonical.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Just as we're able to identify a broken platform using some DT
information, let's enable a way to spot the offenders with ACPI.
The difference is that we can only match on some OEM info instead
of implementation-specific properties. So in order to avoid the
insane multiplication of errata structures, we allow an array
of OEM descriptions to be attached to an erratum structure.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: dann frazier <dann.frazier@canonical.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cortex-A73 (all versions) counter read can return a wrong value
when the counter crosses a 32bit boundary.
The workaround involves performing the read twice, and to return
one or the other depending on whether a transition has taken place.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Userspace being allowed to use read CNTVCT_EL0 anytime (and not
only in the VDSO), we need to enable trapping whenever a cntvct
workaround is enabled on a given CPU.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we're about to allow per CPU cntkctl_el1 configuration, we cannot
rely on the register value to be common when performing power
management.
Let's turn saved_cntkctl into a per-cpu variable.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to access clocksource_counter from the errata handling code,
move it (together with the related structures and functions) towards
the top of the file.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Instead of applying a CPU-specific workaround to all CPUs in the system,
allow it to only affect a subset of them (typical big-little case).
This is done by turning the erratum pointer into a per-CPU variable.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The way we work around errata affecting set_next_event is not very
nice, at it imposes this workaround on errata that do not need it.
Add new workaround hooks and let the existing workarounds use them.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Let's move the handling of workarounds affecting set_next_event
to the affected function, instead of overriding the pointers
as an afterthough. Yes, this is an extra indirection on the
erratum handling path, but the HW is busted anyway.
This will allow for some more flexibility later.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we're about to move things around, let's start with the low
level read/write functions. This allows us to use these functions
in the errata handling code without having to use forward declaration
of static functions.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Should we ever have a workaround for an erratum that is detected using
a capability and affecting a particular CPU, it'd be nice to have
a way to probe them directly.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We're currently stuck with DT when it comes to handling errata, which
is pretty restrictive. In order to make things more flexible, let's
introduce an infrastructure that could support alternative discovery
methods. No change in functionality.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull timer fixes from Thomas Gleixner:
"Two small fixes for the new CLKEVT_OF infrastructure"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
vmlinux.lds: Add __clkevt_of_table to kernel
clockevents: Fix syntax error in clkevt-of macro
The patch fix syntax errors introduced by commit 0c8893c9095d
("clockevents: Add a clkevt-of mechanism like clksrc-of").
Fixes: 0c8893c9095d ("clockevents: Add a clkevt-of mechanism like clksrc-of")
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
With the upcoming NTP correction related rate adjustments to be implemented
in the clockevents core, the latter needs to get informed about every rate
change of a clockevent device made after its registration.
Currently, h8300_timer8 violates this requirement in that it registers its
clockevent device with the correct rate, but resets its ->mult and ->rate
values in timer8_clock_event_start(), called from its ->set_state_oneshot()
function.
It seems like
commit 4633f4cac8 ("clocksource/drivers/h8300: Cleanup startup and
remove module code."),
which introduced the rate initialization at registration, missed to remove
the manual setting of ->mult and ->shift from timer8_clock_event_start().
Purge the setting of ->mult, ->shift, ->min_delta_ns and ->max_delta_ns
from timer8_clock_event_start().
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
With the upcoming NTP correction related rate adjustments to be implemented
in the clockevents core, the latter needs to get informed about every rate
change of a clockevent device made after its registration.
Currently, em_sti violates this requirement in that it registers its
clockevent device with a dummy rate and sets its final rate through
clockevents_config() called from its ->set_state_oneshot().
This patch moves the setting of the clockevent device's rate to its
registration.
I checked all current em_sti users in arch/arm/mach-shmobile and right now,
none of them changes any rate in any clock tree relevant to em_sti after
their respective time_init(). Since all em_sti instances are created after
time_init(), none of them should ever observe any clock rate changes.
- Determine the ->rate value in em_sti_probe() at device probing rather
than at first usage.
- Set the clockevent device's rate at its registration.
- Although not strictly necessary for the upcoming clockevent core changes,
set the clocksource's rate at its registration for consistency.
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Currently, the em_sti driver prepares and enables the needed clock in
em_sti_enable(), potentially called through its clockevent device's
->set_state_oneshot().
However, the clk_prepare() step may sleep whereas tick_program_event() and
thus, ->set_state_oneshot(), can be called in atomic context.
Split the clk_prepare_enable() in em_sti_enable() into two steps:
- prepare the clock at device probing via clk_prepare()
- and enable it in em_sti_enable() via clk_enable().
Slightly reorder resource initialization in em_sti_probe() in order to
facilitate error handling in later patches.
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
With the upcoming NTP correction related rate adjustments to be implemented
in the clockevents core, the latter needs to get informed about every rate
change of a clockevent device made after its registration.
Currently, sh_tmu violates this requirement in that it registers its
clockevent device with a dummy rate and sets its final rate through
clockevents_config() called from its ->set_state_oneshot() and
->set_state_periodic() functions respectively.
This patch moves the setting of the clockevent device's rate to its
registration.
Note that there has been some back and forth regarding this question with
respect to the clocksource also provided by this driver:
commit 66f49121ff ("clocksource: sh_tmu: compute mult and shift before
registration")
moves the rate determination from the clocksource's ->enable() function to
before its registration. OTOH, the later
commit 0aeac458d9 ("clocksource: sh_tmu: __clocksource_updatefreq_hz()
update")
basically reverts this, saying
"Without this patch the old code uses clocksource_register() together
with a hack that assumes a never changing clock rate."
However, I checked all current sh_tmu users in arch/sh as well as in
arch/arm/mach-shmobile carefully and right now, none of them changes any
rate in any clock tree relevant to sh_tmu after their respective
time_init(). Since all sh_tmu instances are created after time_init(), none
of them should ever observe any clock rate changes.
What's more, both, a clocksource as well as a clockevent device, can
immediately get selected for use at their registration and thus, enabled
at this point already. So it's probably safer to assume a "never changing
clock rate" here.
- Move the struct sh_tmu_channel's ->rate member to struct sh_tmu_device:
it's a property of the underlying clock which is in turn specific to
the sh_tmu_device.
- Determine the ->rate value in sh_tmu_setup() at device probing rather
than at first usage.
- Set the clockevent device's rate at its registration.
- Although not strictly necessary for the upcoming clockevent core changes,
set the clocksource's rate at its registration for consistency.
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
With the upcoming NTP correction related rate adjustments to be implemented
in the clockevents core, the latter needs to get informed about every rate
change of a clockevent device made after its registration.
Currently, sh_cmt violates this requirement in that it registers its
clockevent device with a dummy rate and sets its final ->mult and ->shift
values from its ->set_state_oneshot() and ->set_state_periodic() functions
respectively.
This patch moves the setting of the clockevent device's ->mult and ->shift
values to before its registration.
Note that there has been some back and forth regarding this question with
respect to the clocksource also provided by this driver:
commit f4d7c3565c ("clocksource: sh_cmt: compute mult and shift before
registration")
moves the rate determination from the clocksource's ->enable() function to
before its registration. OTOH, the later
commit 3593f5fe40 ("clocksource: sh_cmt: __clocksource_updatefreq_hz()
update")
basically reverts this, saying
"Without this patch the old code uses clocksource_register() together
with a hack that assumes a never changing clock rate."
However, I checked all current sh_cmt users in arch/sh as well as in
arch/arm/mach-shmobile carefully and right now, none of them changes any
rate in any clock tree relevant to sh_cmt after their respective
time_init(). Since all sh_cmt instances are created after time_init(), none
of them should ever observe any clock rate changes.
What's more, both, a clocksource as well as a clockevent device, can
immediately get selected for use at their registration and thus, enabled
at this point already. So it's probably safer to assume a "never changing
clock rate" here.
- Move the struct sh_cmt_channel's ->rate member to struct sh_cmt_device:
it's a property of the underlying clock which is in turn specific to
the sh_cmt_device.
- Determine the ->rate value in sh_cmt_setup() at device probing rather
than at first usage.
- Set the clockevent device's ->mult and ->shift values right before its
registration.
- Although not strictly necessary for the upcoming clockevent core changes,
set the clocksource's rate at its registration for consistency.
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Pull timer fix from Thomas Gleixner:
"Just a simple revert of a new sched_clock implementation which turned
out to be buggy"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "clocksource/drivers/tcb_clksrc: Use 32 bit tcb as sched_clock"
This reverts commit 7b9f1d16e6 ("clocksource/drivers/tcb_clksrc: Use
32 bit tcb as sched_clock"). In the current state, the kernel warns
against a late registration of the new sched_clock, the printk clock
resets after only a few minutes, and it seems that scheduling can be
affected as well.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
We are going to split <linux/sched/clock.h> out of <linux/sched.h>, which
will have to be picked up from other headers and .c files.
Create a trivial placeholder <linux/sched/clock.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull timer updates from Thomas Gleixner:
"Nothing exciting, just the usual pile of fixes, updates and cleanups:
- A bunch of clocksource driver updates
- Removal of CONFIG_TIMER_STATS and the related /proc file
- More posix timer slim down work
- A scalability enhancement in the tick broadcast code
- Math cleanups"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
hrtimer: Catch invalid clockids again
math64, tile: Fix build failure
clocksource/drivers/arm_arch_timer:: Mark cyclecounter __ro_after_init
timerfd: Protect the might cancel mechanism proper
timer_list: Remove useless cast when printing
time: Remove CONFIG_TIMER_STATS
clocksource/drivers/arm_arch_timer: Work around Hisilicon erratum 161010101
clocksource/drivers/arm_arch_timer: Introduce generic errata handling infrastructure
clocksource/drivers/arm_arch_timer: Remove fsl-a008585 parameter
clocksource/drivers/arm_arch_timer: Add dt binding for hisilicon-161010101 erratum
clocksource/drivers/ostm: Add renesas-ostm timer driver
clocksource/drivers/ostm: Document renesas-ostm timer DT bindings
clocksource/drivers/tcb_clksrc: Use 32 bit tcb as sched_clock
clocksource/drivers/gemini: Add driver for the Cortina Gemini
clocksource: add DT bindings for Cortina Gemini
clockevents: Add a clkevt-of mechanism like clksrc-of
tick/broadcast: Reduce lock cacheline contention
timers: Omit POSIX timer stuff from task_struct when disabled
x86/timer: Make delay() work during early bootup
delay: Add explanation of udelay() inaccuracy
...
Erratum Hisilicon-161010101 says that the ARM generic timer counter "has
the potential to contain an erroneous value when the timer value
changes". Accesses to TVAL (both read and write) are also affected due
to the implicit counter read. Accesses to CVAL are not affected.
The workaround is to reread the system count registers until the value
of the second read is larger than the first one by less than 32, the
system counter can be guaranteed not to return wrong value twice by
back-to-back read and the error value is always larger than the correct
one by 32. Writes to TVAL are replaced with an equivalent write to CVAL.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
[Mark: split patch, fix Kconfig, reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Currently we have code inline in the arch timer probe path to cater for
Freescale erratum A-008585, complete with ifdeffery. This is a little
ugly, and will get worse as we try to add more errata handling.
This patch refactors the handling of Freescale erratum A-008585. Now the
erratum is described in a generic arch_timer_erratum_workaround
structure, and the probe path can iterate over these to detect errata
and enable workarounds.
This will simplify the addition and maintenance of code handling
Hisilicon erratum 161010101.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
[Mark: split patch, correct Kconfig, reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Having a command line option to flip the errata handling for a
particular erratum is a little bit unusual, and it's vastly superior to
pass this in the DT. By common consensus, it's best to kill off the
command line parameter.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
[Mark: split patch, reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This patch adds a OSTM driver for the Renesas architecture.
The OS Timer (OSTM) has independent channels that can be
used as a freerun or interval times.
This driver uses the first probed device as a clocksource
and then any additional devices as clock events.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
On newer boards the TC can be read as single 32 bit value without locking.
Thus the clock can be used as reference for sched_clock which is much more
accurate than the jiffies implementation.
Tested on a Atmel SAMA5D2 board.
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This is a rewrite of the Gemini timer
driver in arch/arm/mach-gemini/timer.c trying to do everything
the device tree way:
- Make every IO-access relative to a base address and dynamic
so we can do a dynamic ioremap and get going.
- Do not poke around directly in the global syscon registers,
access them using the syscon regmap style design pattern for
the one register we need to check.
- Find register range and interrupt from the device tree.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The current code uses the CLOCKSOURCE_OF_DECLARE macro to fill the clksrc
table with a t-uple (name, init_function).
Unfortunately it ends up to the clockevent and the clocksource being
both initialized with this macro. It is not a problem by itself but there
is not a clear distinction between a clockevent and a clocksource in the
code initialization path. Somebody can argue there are the same IP block
and the same DT node. But conceptually from the software side, there are
two distincts entities and as is they should be initialized separetely.
Some drivers which do not have a clocksource end up by using the
CLOCKSOURCE_OF_DECLARE macro to declare a clockevent.
Another result is the fuzzy organization in the clocksource directory,
where the clockevents are implemented in the same file than the
clocksources or file labelled timer-something implementing a clocksource.
This patch provides another macro to specifically declare a clockevent in
the same way than the clocksource and gives the opportunity to write two
separate drivers, one for the clocksource and another for the clockevents.
Hopefully, that can help to do some housework in the directory, perhaps
split the drivers in to entities, for example:
- clksrc-rockchip.c
- clkevt-rockchip.c
Also, it gives the possibility to declare clocksources separately in the
DT and then use a clocksource from IP block while while clockevents are
used from another IP block.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
When a CPU goes offline a potentially pending timer interrupt is not
cleared. When the CPU comes online again then the pending interrupt is
delivered before the per cpu clockevent device is initialized. As a
consequence the tick interrupt handler dereferences a NULL pointer.
[ 51.251378] Unable to handle kernel NULL pointer dereference at virtual address 00000040
[ 51.289348] task: ee942d00 task.stack: ee960000
[ 51.293861] PC is at tick_periodic+0x38/0xb0
[ 51.298102] LR is at tick_handle_periodic+0x1c/0x90
Clear the pending interrupt in the cpu dying path.
Fixes: 56a94f1391 ("clocksource: exynos_mct: Avoid blocking calls in the cpu hotplug notifier")
Reported-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Cc: cw00.choi@samsung.com
Cc: daniel.lezcano@linaro.org
Cc: stable@vger.kernel.org
Cc: javier@osg.samsung.com
Cc: kgene@kernel.org
Cc: krzk@kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1484628876-22065-1-git-send-email-jy0922.shim@samsung.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull timer type cleanups from Thomas Gleixner:
"This series does a tree wide cleanup of types related to
timers/timekeeping.
- Get rid of cycles_t and use a plain u64. The type is not really
helpful and caused more confusion than clarity
- Get rid of the ktime union. The union has become useless as we use
the scalar nanoseconds storage unconditionally now. The 32bit
timespec alike storage got removed due to the Y2038 limitations
some time ago.
That leaves the odd union access around for no reason. Clean it up.
Both changes have been done with coccinelle and a small amount of
manual mopping up"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ktime: Get rid of ktime_equal()
ktime: Cleanup ktime_set() usage
ktime: Get rid of the union
clocksource: Use a plain u64 instead of cycle_t
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If of_iomap() or any other subsequent function fails moxart_timer_init()
exits without freeing memory and unmapping the timer base.
Add proper cleanup points.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: http://lkml.kernel.org/r/1482099996-1524-1-git-send-email-sudipm.mukherjee@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
These are updates for platform specific code on 32-bit ARM machines,
essentially anything that can not (yet) be expressed using DT files.
Noteworthy changes include:
- Added support for the TI DRA71x family of SoCs in mach-omap2,
this is an new variant of the the DRA72x/DRA74x automotive
infotainment chips we already supported for a while.
- Added support for the ST STM32F746 SoC, the first Cortex-M7
based microcontroller we support, related to the smaller
STM32F4 family.
- Renesas adds support for r8a7743 and r8a7745 in mach-shmobile,
see http://elinux.org/RZ-G
- SMP is now supported on the OX820 platform
- A lot of code in mach-omap2 gets removed as a follow-up to
removing support for board files in the previous release
- Davinci has some new work to improve USB support
- For i.MX, the performance monitor now supports profiling the
memory controller using 'perf'
Conflicts:
arch/arm/mach-shmobile/setup-rcar-gen2.c: rcar_gen2_clocks_init()
is gone, calling of_clk_init(NULL) is sufficient now.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BF6Y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"These are updates for platform specific code on 32-bit ARM machines,
essentially anything that can not (yet) be expressed using DT files.
Noteworthy changes include:
- Added support for the TI DRA71x family of SoCs in mach-omap2, this
is an new variant of the the DRA72x/DRA74x automotive infotainment
chips we already supported for a while.
- Added support for the ST STM32F746 SoC, the first Cortex-M7 based
microcontroller we support, related to the smaller STM32F4 family.
- Renesas adds support for r8a7743 and r8a7745 in mach-shmobile, see
http://elinux.org/RZ-G
- SMP is now supported on the OX820 platform
- A lot of code in mach-omap2 gets removed as a follow-up to removing
support for board files in the previous release
- Davinci has some new work to improve USB support
- For i.MX, the performance monitor now supports profiling the memory
controller using 'perf'"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (95 commits)
ARM: davinci: da830-evm: use gpio descriptor for mmc pins
ARM: davinci: da850-evm: use gpio descriptor for mmc pins
ARM: davinci: hawk: use gpio descriptor for mmc pins
ARM: ARTPEC-6: add select MFD_SYSCON to MACH_ARTPEC6
ARM: davinci: da8xx: Fix ohci device name
ARM: oxnas: Add OX820 config and makefile entry
ARM: oxnas: Add OX820 SMP support
ARM: davinci: PM: fix build when da850 not compiled in
ARM: orion5x: remove legacy support of ls-chl
ARM: integrator: drop EBI access use syscon
ARM: BCM5301X: Add back handler ignoring external imprecise aborts
ARM: davinci: PM: support da8xx DT platforms
ARM: davinci: PM: cleanup: remove references to pdata
ARM: davinci: PM: rework init, remove platform device
ARM: Kconfig: Introduce MACH_STM32F746 flag
ARM: mach-stm32: Add a new SOC - STM32F746
ARM: shmobile: document SK-RZG1E board
ARM: shmobile: r8a7745: basic SoC support
ARM: imx: mach-imx6ul: add imx6ull support
ARM: zynq: Reserve correct amount of non-DMA RAM
...
- Moving ARC timer driver into drivers/clocksource
- EZChip timer driver updates [Noam]
- ARC AXS103 and HAPS platform updates [Alexey]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1Hlx
-----END PGP SIGNATURE-----
Merge tag 'arc-4.10-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"These are mostly timer/clocksource driver updates which were
Reviewed/Acked by Daniel but had to be merged via ARC tree due to
dependencies.
I will follow up with another pull request with actual ARC changes
early next week !
Summary:
- Moving ARC timer driver into drivers/clocksource
- EZChip timer driver updates [Noam]
- ARC AXS103 and HAPS platform updates [Alexey]"
* tag 'arc-4.10-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: axs10x: really enable ARC PGU
ARC: rename Zebu platform support to HAPS
clocksource: nps: avoid maybe-uninitialized warning
clocksource: Add clockevent support to NPS400 driver
clocksource: update "fn" at CLOCKSOURCE_OF_DECLARE() of nps400 timer
soc: Support for NPS HW scheduling
clocksource: import ARC timer driver
ARC: breakout timer include code into separate header ...
ARC: move mcip.h into include/soc and adjust the includes
ARC: breakout aux handling into a separate header
ARC: time: move time_init() out of the driver
ARC: timer: gfrc, rtc: build under same option (64-bit timers)
ARC: timer: gfrc, rtc: Read BCR to detect whether hardware exists ...
ARC: timer: gfrc, rtc: deuglify big endian code
We get a harmless false-positive warning with the newly added nps
clocksource driver:
drivers/clocksource/timer-nps.c: In function 'nps_setup_clocksource':
drivers/clocksource/timer-nps.c:102:6: error: 'nps_timer1_freq' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Gcc here fails to identify that IS_ERR() is only true if PTR_ERR()
has a nonzero value. Using PTR_ERR_OR_ZERO() to convert the result
first makes this obvious and shuts up the warning.
Fixes: 0ee4d9922df5 ("clocksource: Add clockevent support to NPS400 driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Till now we used clockevent from generic ARC driver.
This was enough as long as we worked with simple multicore SoC.
When we are working with multithread SoC each HW thread can be
scheduled to receive timer interrupt using timer mask register.
This patch will provide a way to control clock events per HW thread.
The design idea is that for each core there is dedicated register
(TSI) serving all 16 HW threads.
The register is a bitmask with one bit for each HW thread.
When HW thread wants that next expiration of timer interrupt will
hit it then the proper bit should be set in this dedicated register.
When timer expires all HW threads within this core which their bit
is set at the TSI register will be interrupted.
Driver can be used from device tree by:
compatible = "ezchip,nps400-timer0" <-- for clocksource
compatible = "ezchip,nps400-timer1" <-- for clockevent
Note that name convention for timer0/timer1 was taken from legacy
ARC design. This design is our base before adding HW threads.
For backward compatibility we keep "ezchip,nps400-timer" for clocksource
Signed-off-by: Noam Camus <noamca@mellanox.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
nps_setup_clocksource() should take node as only argument as defined by
typedef int (*of_init_fn_1_ret)(struct device_node *)
Therefore need to replace:
int __init nps_setup_clocksource(struct device_node *node, struct clk *clk)
with
int __init nps_setup_clocksource(struct device_node *node)
This patch also serve as preparation for next patch which add support
for clockevents to nps400.
Specifically we add new function nps_get_timer_clk() to serve clocksource
and later clockevent registration.
Signed-off-by: Noam Camus <noamca@mellanox.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This adds support for
- CONFIG_ARC_TIMERS : legacy 32-bit TIMER0 and TIMER1 which count UP
from @CNT to @LIMIT, before optionally triggering an interrupt.
These are programmed using ARC auxiliary register interface.
These are present in all ARC cores (ARC700 and ARC HS38)
TIMER0 serves as clockevent for all ARC linux builds.
TIMER1 is used for clocksource in arc700 builds.
- CONFIG_ARC_TIMERS_64BIT: 64-bit counters, RTC and GFRC found in
ARC HS38 cores. These are independnet IP blocks with different
programming model respectively.
Link: http://lkml.kernel.org/r/20161111231132.GA4186@mai
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Free memory mapping, if bcm2835_timer_init is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Let's use the of_io_request_and_map() API so that the frame
region is protected and shows up in /proc/iomem.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
The ARM specifies that the system counter "must be implemented in an
always-on power domain," and so we try to use the counter as a source of
timekeeping across suspend/resume. Unfortunately, some SoCs (e.g.,
Rockchip's RK3399) do not keep the counter ticking properly when
switched from their high-power clock to the lower-power clock used in
system suspend. Support this quirk by adding a new device tree property.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This cycle is covering :
- some clock fixes common with sa1100 architecture
- the consequence of the pxa_camera conversion to v4l2
- a small irq related fix for pxa25x device-tree only
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1WrE
-----END PGP SIGNATURE-----
Merge tag 'pxa-for-4.10' of https://github.com/rjarzmik/linux into next/soc
This is the pxa changes for v4.10 cycle.
This cycle is covering :
- some clock fixes common with sa1100 architecture
- the consequence of the pxa_camera conversion to v4l2
- a small irq related fix for pxa25x device-tree only
* tag 'pxa-for-4.10' of https://github.com/rjarzmik/linux:
ARM: pxa: fix pxa25x interrupt init
ARM: pxa: remove duplicated include from spitz.c
ARM: pxa: em-x270: use the new pxa_camera platform_data
ARM: pxa: ezx: use the new pxa_camera platform_data
ARM: pxa: mioa701: use the new pxa_camera platform_data
ARM: pxa: pxa_cplds: honor probe deferral
ARM: sa11x0/pxa: get rid of get_clock_tick_rate
watchdog: sa11x0/pxa: get rid of get_clock_tick_rate
ARM: sa11x0/pxa: acquire timer rate from the clock rate
clk: pxa25x: OSTIMER0 clocks from the main oscillator
Signed-off-by: Olof Johansson <olof@lixom.net>
struct clocksource is also used by the clk notifier callback, to
unregister and re-register the clocksource with a different clock rate.
clocksource_mmio_init does not pass back a pointer to the struct used,
and the clk notifier callback assumes that the struct clocksource in
struct sun5i_timer_clksrc is valid. This results in a kernel NULL
pointer dereference when the hstimer clock is changed:
Unable to handle kernel NULL pointer dereference at virtual address 00000004
[<c03a4678>] (clocksource_unbind) from [<c03a46d4>] (clocksource_unregister+0x2c/0x44)
[<c03a46d4>] (clocksource_unregister) from [<c0a6f350>] (sun5i_rate_cb_clksrc+0x34/0x3c)
[<c0a6f350>] (sun5i_rate_cb_clksrc) from [<c035ea50>] (notifier_call_chain+0x44/0x84)
[<c035ea50>] (notifier_call_chain) from [<c035edc0>] (__srcu_notifier_call_chain+0x44/0x60)
[<c035edc0>] (__srcu_notifier_call_chain) from [<c035edf4>] (srcu_notifier_call_chain+0x18/0x20)
[<c035edf4>] (srcu_notifier_call_chain) from [<c0670174>] (__clk_notify+0x70/0x7c)
[<c0670174>] (__clk_notify) from [<c06702c0>] (clk_propagate_rate_change+0xa4/0xc4)
[<c06702c0>] (clk_propagate_rate_change) from [<c0670288>] (clk_propagate_rate_change+0x6c/0xc4)
Revert the commit for now. clocksource_mmio_init can be made to pass back
a pointer, but the code churn and usage of an inner struct might not be
worth it.
Fixes: 157dfadef8 ("clocksource/drivers/timer_sun5i: Replace code by clocksource_mmio_init")
Reported-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: linux-sunxi@googlegroups.com
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20161018054918.26855-1-wens@csie.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
At the hardware level, the J-Core PIT is integrated with the interrupt
controller, but it is represented as its own device and has an
independent programming interface. It provides a 12-bit countdown
timer, which is not presently used, and a periodic timer. The interval
length for the latter is programmable via a 32-bit throttle register
whose units are determined by a bus-period register. The periodic
timer is used to implement both periodic and oneshot clock event
modes; in oneshot mode the interrupt handler simply disables the timer
as soon as it fires.
Despite its device tree node representing an interrupt for the PIT,
the actual irq generated is programmable, not hard-wired. The driver
is responsible for programming the PIT to generate the hardware irq
number that the DT assigns to it.
On SMP configurations, J-Core provides cpu-local instances of the PIT;
no broadcast timer is needed. This driver supports the creation of the
necessary per-cpu clock_event_device instances.
A nanosecond-resolution clocksource is provided using the J-Core "RTC"
registers, which give a 64-bit seconds count and 32-bit nanoseconds
that wrap every second. The driver converts these to a full-range
32-bit nanoseconds count.
Signed-off-by: Rich Felker <dalias@libc.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Link: http://lkml.kernel.org/r/b591ff12cc5ebf63d1edc98da26046f95a233814.1476393790.git.dalias@libc.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
As both pxa and sa1100 provide a clock to the timer, the rate can be
inferred from the clock rather than hard encoded in a functional call.
This patch changes the pxa timer to have a mandatory clock which is used
as the timer rate.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Driver updates for ARM SoCs, including a couple of newly added drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for the
EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAV/gaimCrR//JCVInAQJaOQ/6A++YfLVmdF4wxgcu/0ti28lA7SkQIGJV
UAsfCmqMEutbeDvnloVGmTV2K2NS7mzxdxsJGbVB7Oe/zdOFN+T9sf9hAlId01QA
oVkoagpofoxlyKoKJ/l+heuEEZMa0Ekk3XXRTGv/Ovymo7252o4tEdGu9c+gyaMJ
KqgixcrQRzxuWDgPpHUPUez2vY1iRMvvdcb0EmfiHcIgPOEJc6MIxulsqEIrkoMz
WYeGFIeqRJxnrur3QD8WnD+aZD6bV01wkFTkWXGWg4H87QfEESgVBu5A7TL+5sL8
1SlX/b7S5/ZJbrOiOS2IUyvbK7NiA/Q+NunHW2rMVnUWuEvJ9HAQB1kVSQH5LIYO
6OBokjcijm6m/j6O6fdDfvNd6PLsIEUqfWVws7O+uofMMqKPxqak4VBTRdFM+aeF
ZtK7mEbzteCX0bnC+XblZrseAlkIehYnP80CLDbtDTerTWP4gsjxGVt3U6MO0NzB
K0ACWZOclzrcFscNKrmP6uPCpfZriiPV/XMCEHcylA/X2iYsVmpqKzdLuNs5aeUr
uPzQbNWu9ygg/bDRXMYY2E3Kzjsc0eIOKEOPyhLaZdSo4e1FQxud6L2V2Vj0RLB/
iMA7/CyQZqn6Yzgs0VMZm/bnh+hIdHioGFl5K5j6Fcw9VZRkNmnEQJzX4VU5efGO
g1+5av0vFXg=
=GvTq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for
the EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
bus: qcom-ebi2: depend on HAS_IOMEM
pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
clk: mvebu: Add clk support for the orion5x SoC mv88f5181
dt-bindings: EXYNOS: Add Exynos5433 PMU compatible
clocksource: exynos_mct: Add the support for ARM64
perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver
Documentation: Add documentation for APM X-Gene SoC PMU DTS binding
MAINTAINERS: Add entry for APM X-Gene SoC PMU driver
bus: qcom: add EBI2 driver
bus: qcom: add EBI2 device tree bindings
rtc: rtc-pm8xxx: Add support for pm8018 rtc
nvmem: amlogic: Add Amlogic Meson EFUSE driver
firmware: Amlogic: Add secure monitor driver
soc: qcom: smd: Reset rx tail rather than tx
memory: atmel-sdramc: fix a possible NULL dereference
reset: hi6220: allow to compile test driver on other architectures
reset: zynq: add driver Kconfig option
reset: sunxi: add driver Kconfig option
reset: stm32: add driver Kconfig option
reset: socfpga: add driver Kconfig option
...
Pull timer updates from Thomas Gleixner:
"A rather smalish set of updates for timers and timekeeping:
- Two core fixes to prevent potential undefinded behaviour about
which gcc is complaining rightfully.
- A fix to prevent stopping the tick on an (soon) offline CPU so it
can complete the shutdown procedure.
- Wait for clocks to stabilize before making decisions, so a not yet
validated clock is not rejected.
- The usual pile of fixes to the various clocksource drivers.
- Core code typo and include fixlets"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Include the correct header for errno definitions
clocksource/drivers/ti-32k: Prevent ftrace recursion
clocksource/mips-gic-timer: Stop checking cpu_has_counter
clocksource/mips-gic-timer: Print an error if IRQ setup fails
tick/nohz: Prevent stopping the tick on an offline CPU
clocksource/drivers/oxnas: Add OX820 compatible
clocksource/drivers/timer-atmel-pit: Simplify IRQ handler
clocksource/drivers/timer-atmel-pit: Remove uselesss WARN_ON_ONCE
clocksource/drivers/timer-atmel-pit: Drop at91sam926x_pit_common_init
clocksource/drivers/moxart: Replace panic by pr_err
clocksource/drivers/moxart: Replace setup_irq by request_irq
clocksource/drivers/moxart: Add Aspeed support
clocksource/drivers/moxart: Use struct to hold state
clocksource/drivers/moxart: Refactor enable/disable
time: Avoid undefined behaviour in ktime_add_safe()
time: Avoid undefined behaviour in timespec64_add_safe()
timekeeping: Prints the amounts of time spent during suspend
clocksource: Defer override invalidation unless clock is unstable
hrtimer: Spelling fixes
- Support for execute-only page permissions
- Support for hibernate and DEBUG_PAGEALLOC
- Support for heterogeneous systems with mismatches cache line sizes
- Errata workarounds (A53 843419 update and QorIQ A-008585 timer bug)
- arm64 PMU perf updates, including cpumasks for heterogeneous systems
- Set UTS_MACHINE for building rpm packages
- Yet another head.S tidy-up
- Some cleanups and refactoring, particularly in the NUMA code
- Lots of random, non-critical fixes across the board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJX7k31AAoJELescNyEwWM0XX0H/iOaWCfKlWOhvBsStGUCsLrK
XryTzQT2KjdnLKf3jwP+1ateCuBR5ROurYxoDCX5/7mD63c5KiI338Vbv61a1lE1
AAwjt1stmQVUg/j+kqnuQwB/0DYg+2C8se3D3q5Iyn7zc19cDZJEGcBHNrvLMufc
XgHrgHgl/rzBDDlHJXleknDFge/MfhU5/Q1vJMRRb4JYrpAtmIokzCO75CYMRcCT
ND2QbmppKtsyuFPGUTVbAFzJlP6dGKb3eruYta7/ct5d0pJQxav3u98D2yWGfjdM
YaYq1EmX5Pol7rWumqLtk0+mA9yCFcKLLc+PrJu20Vx0UkvOq8G8Xt70sHNvZU8=
=gdPM
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"It's a bit all over the place this time with no "killer feature" to
speak of. Support for mismatched cache line sizes should help people
seeing whacky JIT failures on some SoCs, and the big.LITTLE perf
updates have been a long time coming, but a lot of the changes here
are cleanups.
We stray outside arch/arm64 in a few areas: the arch/arm/ arch_timer
workaround is acked by Russell, the DT/OF bits are acked by Rob, the
arch_timer clocksource changes acked by Marc, CPU hotplug by tglx and
jump_label by Peter (all CC'd).
Summary:
- Support for execute-only page permissions
- Support for hibernate and DEBUG_PAGEALLOC
- Support for heterogeneous systems with mismatches cache line sizes
- Errata workarounds (A53 843419 update and QorIQ A-008585 timer bug)
- arm64 PMU perf updates, including cpumasks for heterogeneous systems
- Set UTS_MACHINE for building rpm packages
- Yet another head.S tidy-up
- Some cleanups and refactoring, particularly in the NUMA code
- Lots of random, non-critical fixes across the board"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (100 commits)
arm64: tlbflush.h: add __tlbi() macro
arm64: Kconfig: remove SMP dependence for NUMA
arm64: Kconfig: select OF/ACPI_NUMA under NUMA config
arm64: fix dump_backtrace/unwind_frame with NULL tsk
arm/arm64: arch_timer: Use archdata to indicate vdso suitability
arm64: arch_timer: Work around QorIQ Erratum A-008585
arm64: arch_timer: Add device tree binding for A-008585 erratum
arm64: Correctly bounds check virt_addr_valid
arm64: migrate exception table users off module.h and onto extable.h
arm64: pmu: Hoist pmu platform device name
arm64: pmu: Probe default hw/cache counters
arm64: pmu: add fallback probe table
MAINTAINERS: Update ARM PMU PROFILING AND DEBUGGING entry
arm64: Improve kprobes test for atomic sequence
arm64/kvm: use alternative auto-nop
arm64: use alternative auto-nop
arm64: alternative: add auto-nop infrastructure
arm64: lse: convert lse alternatives NOP padding to use __nops
arm64: barriers: introduce nops and __nops macros for NOP sequences
arm64: sysreg: replace open-coded mrs_s/msr_s with {read,write}_sysreg_s
...
Instead of comparing the name to a magic string, use archdata to
explicitly communicate whether the arch timer is suitable for
direct vdso access.
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Erratum A-008585 says that the ARM generic timer counter "has the
potential to contain an erroneous value for a small number of core
clock cycles every time the timer value changes". Accesses to TVAL
(both read and write) are also affected due to the implicit counter
read. Accesses to CVAL are not affected.
The workaround is to reread TVAL and count registers until successive
reads return the same value. Writes to TVAL are replaced with an
equivalent write to CVAL.
The workaround is to reread TVAL and count registers until successive reads
return the same value, and when writing TVAL to retry until counter
reads before and after the write return the same value.
The workaround is enabled if the fsl,erratum-a008585 property is found in
the timer node in the device tree. This can be overridden with the
clocksource.arm_arch_timer.fsl-a008585 boot parameter, which allows KVM
users to enable the workaround until a mechanism is implemented to
automatically communicate this information.
This erratum can be found on LS1043A and LS2080A.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Scott Wood <oss@buserror.net>
[will: renamed read macro to reflect that it's not usually unstable]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently ti-32k can be used as a scheduler clock. We properly marked
omap_32k_read_sched_clock() as notrace but we then call another
function ti_32k_read_cycles() that _wasn't_ notrace.
Having a traceable function in the sched_clock() path leads to a
recursion within ftrace and a kernel crash.
Fix this by adding notrace attribute to the ti_32k_read_cycles()
function.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Cc: daniel.lezcano@linaro.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20160922075621.3725-1-jszhang@marvell.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The cpu_has_counter macro indicates whether the current CPU has a
working coprocessor 0 count & compare registers, and has no bearing on
the GIC. Stop checking it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/20160913165644.627-2-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We've checked for errors from setup_irq_percpu since commit f95ac8558b
("CLOCKSOURCE: mips-gic: Add missing error returns checks") but didn't
print an error message in the failure case. This makes it very easy to
overlook the GIC timer clock event driver not being registered, since
we'll generally just use a different clock event driver if that happens.
Print an error if IRQ setup fails in order to make such problems harder
to miss (ie. not completely silent).
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/20160913165644.627-1-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
1. Allow compile testing of exynos-mct clocksource driver on ARM64.
2. Document Exynos5433 PMU compatible (already used by clkout driver and more
will be coming soon).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WOAL
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/drivers
Pull "Samsung drivers/soc update for v4.9" from Krzysztof Kozlowski:
1. Allow compile testing of exynos-mct clocksource driver on ARM64.
2. Document Exynos5433 PMU compatible (already used by clkout driver and more
will be coming soon).
* tag 'samsung-drivers-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: EXYNOS: Add Exynos5433 PMU compatible
clocksource: exynos_mct: Add the support for ARM64
This patch allows building and compile-testing the driver also for
ARM64. The delay_timer is only supported on ARMv7.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[k.kozlowski: Adjusted commit msg]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
In order to support the Oxford Semiconductor OX820 SoC, add new
compatible string to rps timer driver.
Also add new string in the dt-bindings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Because the PIT is also a proper clocksource, the timekeeping code is
already able to handle lost ticks.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
IRQ handlers are running with IRQ disabled for a while, remove wrong
comment and useless test.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Merge at91sam926x_pit_common_init in at91sam926x_pit_dt_init as this is the
only initialization method now.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The clksrc-of code is supposed to catch the return code and fail gracefully.
Don't panic on error, but print the error and exit with a relevant error
code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Save memory space and line of code by replacing setup_irq by request_irq.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Joel Stanley <joel@jms.id.au>
The Aspeed SoC has timer IP with a very similar register layout to the
moxart timer. This patch adds support for the fourth and fifth gen
aspeed SoCs, and has been tested on the ast2400 and ast2500.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add a struct moxart_timer to hold the driver state, including the
irqaction and struct clock_event_device.
Most importantly this holds values for enabling and disabling the timer,
so future support can be added for devices that use different bits for
enable/disable.
In preparation for future hardware support we add a MOXART prefix to the
existing values.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This patch abstracts the enable and disable register writes into their
own functions in preparation for future changes to use SoC specific
values for the writes.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The previous fix introduced a check against the ret variable which
is not defined, hence producing a compilation error:
linux/drivers/clocksource/timer-atmel-pit.c: In function ‘at91sam926x_pit_dt_init’:
linux/drivers/clocksource/timer-atmel-pit.c:264:2: error: ‘ret’ undeclared (first use in this function)
ret = clk_prepare_enable(data->mck);
^
linux/drivers/clocksource/timer-atmel-pit.c:264:2: note: each undeclared identifier is reported only once for each function it appears in
Add the missing the variable 'ret'.
Fixes: 504f34c9e4 "clocksource/drivers/atmel-pit: Convert init function to return error"
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: alexandre.belloni@free-electrons.com
Cc: motobud@gmail.com
Cc: realbright@lgcns.com
Link: http://lkml.kernel.org/r/1472453043-24287-1-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The bootloader (U-boot) sometimes uses this timer for various delays.
It uses it as a ongoing counter, and does comparisons on the current
counter value. The timer counter is never stopped.
In some cases when the user interacts with the bootloader, or lets
it idle for some time before loading Linux, the timer may expire,
and an interrupt will be pending. This results in an unexpected
interrupt when the timer interrupt is enabled by the kernel, at
which point the event_handler isn't set yet. This results in a NULL
pointer dereference exception, panic, and no way to reboot.
Clear any pending interrupts after we stop the timer in the probe
function to avoid this.
Cc: stable@vger.kernel.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Driver init code incorrectly uses the block base address and as a result
clears clocksource structure's fields instead of the hardware registers.
Commit 09a9982016 ("timekeeping: Lift clocksource cacheline
restriction") has changed the offsets within pistachio_clocksource
structure and what has previously gone unnoticed now leads to a kernel
panic during boot.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
mck is needed to get the PIT working. Explicitly prepare_enable it instead
of assuming it is enabled.
This solves an issue where the system is freezing when the ETM/ETB drivers
are enabled.
Reported-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
We get 1 warning about global functions without a declaration in the
clocksource/drivers/pxa driver when building with W=1:
drivers/clocksource/pxa_timer.c:221:13: warning: no previous prototype for 'pxa_timer_nodt_init' [-Wmissing-prototypes]
void __init pxa_timer_nodt_init(int irq, void __iomem *base,
In fact, this function is declared in pxa.h, so this patch
add missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: daniel.lezcano@linaro.org
Cc: xie.baoyou@zte.com.cn
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1471965569-4104-1-git-send-email-baoyou.xie@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In commit:
d8152bf85d ("clocksource/drivers/mips-gic-timer: Convert init function to return error")
several return values were added to a void function resulting in the following warnings:
clocksource/mips-gic-timer.c: In function 'gic_clocksource_of_init':
clocksource/mips-gic-timer.c:175:3: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:183:4: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:190:3: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:195:3: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:200:3: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:211:2: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c: At top level:
clocksource/mips-gic-timer.c:213:1: warning: comparison of distinct pointer types lacks a cast [enabled by default]
clocksource/mips-gic-timer.c: In function 'gic_clocksource_of_init':
clocksource/mips-gic-timer.c:183:18: warning: ignoring return value of 'PTR_ERR', declared with attribute warn_unused_result [-Wunused-result]
Given that the addition of the return values was intentional, it seems
that the conversion of the containing function from void to int was
simply overlooked.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Fixes: d8152bf85d ("clocksource/drivers/mips-gic-timer: Convert init function to return error")
Link: http://lkml.kernel.org/r/1471429296-9053-3-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I could not figure out why, but GCC cannot prove that the
kona_timer_init() function always initializes its two outputs,
and we get a warning for the use of the 'lsw' variable later,
which is obviously correct.
drivers/clocksource/bcm_kona_timer.c: In function 'kona_timer_init':
drivers/clocksource/bcm_kona_timer.c:119:13: error: 'lsw' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Slightly reordering the loop makes the warning disappear, after
it becomes more obvious to the compiler that the loop is
always entered on the first iteration.
As pointed out by Ray Jui, there is a related problem in the
way we deal with the loop running into the limit, as we just
keep going there with an invalid counter data, so instead we
now propagate a -ETIMEDOUT result to the caller.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bcm-kernel-feedback-list@broadcom.com
Link: http://lkml.kernel.org/r/1471429296-9053-2-git-send-email-daniel.lezcano@linaro.org
Link: https://patchwork.kernel.org/patch/9174261/
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While converting the init function to return an error, the wrong clock
was get. This leads to the wrong clock rate and slows down the kernel.
For example, it affects typical boot time:
- without fix: over 1 minute
- with fix: 15 seconds
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 12549e27c6 ("clocksource/drivers/time-armada-370-xp: Convert init function to return error")
Link: http://lkml.kernel.org/r/1471429296-9053-1-git-send-email-daniel.lezcano@linaro.org
[ Refined the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
The ARM architected timer produces level-triggered interrupts (this
is mandated by the architecture). Unfortunately, a number of
device-trees get this wrong, and expose an edge-triggered interrupt.
Until now, this wasn't too much an issue, as the programming of the
trigger would fail (the corresponding PPI cannot be reconfigured),
and the kernel would be happy with this. But we're about to change
this, and trust DT a lot if the driver doesn't provide its own
trigger information. In that context, the timer breaks badly.
While we do need to fix the DTs, there is also some userspace out
there (kvmtool) that generates the same kind of broken DT on the
fly, and that will completely break with newer kernels.
As a safety measure, and to keep buggy software alive as well as
buying us some time to fix DTs all over the place, let's check
what trigger configuration has been given us by the firmware.
If this is not a level configuration, then we know that the
DT/ACPI configuration is bust, and we pick some defaults which
won't be worse than the existing setup.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Liu Gang <Gang.Liu@nxp.com>
Cc: Mark Rutland <marc.rutland@arm.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Wenbin Song <Wenbin.Song@freescale.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: arm@kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Ray Jui <rjui@broadcom.com>
Cc: "Hou Zhiqiang" <B48286@freescale.com>
Cc: Tirumalesh Chalamarla <tchalamarla@cavium.com>
Cc: linux-samsung-soc@vger.kernel.org
Cc: Yuan Yao <yao.yuan@nxp.com>
Cc: Jan Glauber <jglauber@cavium.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: linux-amlogic@lists.infradead.org
Cc: soren.brinkmann@xilinx.com
Cc: Rajesh Bhagat <rajesh.bhagat@freescale.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Carlo Caione <carlo@caione.org>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Link: http://lkml.kernel.org/r/1470045256-9032-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Barry Song <baohua@kernel.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153338.310333816@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153338.229913786@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-samsung-soc@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153338.147940411@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel@stlinux.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153338.062741642@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153336.380737946@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153336.295486558@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-metag@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153336.215137642@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153336.130385842@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153336.048259040@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The failure check of armada_370_xp_timer_setup() in
armada_370_xp_timer_common_init() is negated. This leads to an error message
and exit in case of a successful initialization. Remove the stray '!'.
Fixes: 12549e27c6 ("clocksource/drivers/time-armada-370-xp: Convert init function to return error")
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1607121731020.1344@hypnos.tec.linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
IS_ERR and PTR_ERR should use the same variable, clk_ce in this case.
Fixes: 4de1eb07c47f (Convert init function to return error)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
This patch changes the compatibility string to match with the smallest
supported chip (EP7209). Since the DT-support for this CPU is not yet
announced, this change is safe.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Disabling the eventstream can be useful for both remotely debugging a
deployed production system and development of code using WFE-based
polling loops. Whilst this can currently be controlled via a Kconfig
option (CONFIG_ARM_ARCH_TIMER_EVTSTREAM), it's often desirable to toggle
the feature on the command line, so this patch adds a new command-line
option ("clocksource.arm_arch_timer.evtstrm") to do just that. The
default behaviour is determined based on CONFIG_ARM_ARCH_TIMER_EVTSTREAM.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach,
allowing the user to compile the driver on different platforms.
The current option let the user to select the clocksource or not.
The Kconfig option policy is to let the platform to select the
timer automatically.
Add the COMPILE_TEST option, so the prompt to select the driver will
be showed only when COMPILE_TEST is set and will let this driver
to compile on different platform, thus increasing the compilation
test coverage.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach,
allowing the user to compile the driver on different platforms.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach,
allowing the user to compile the driver on different platforms.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_INTEGRATOR_AP_TIMER and is selected
by the platform. Then the clocksource's Kconfig is changed to make this
option selectable by the user if the COMPILE_TEST option is set. Otherwise,
it is up to the platform's Kconfig to select the timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_KEYSTONE_TIMER and is selected by the
platform. Then the clocksource's Kconfig is changed to make this option
selectable by the user if the COMPILE_TEST option is set. Otherwise, it is
up to the platform's Kconfig to select the timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_NSPIRE_TIMER and is selected by the
platform. Then the clocksource's Kconfig is changed to make this option
selectable by the user if the COMPILE_TEST option is set. Otherwise, it is
up to the platform's Kconfig to select the timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_U300_TIMER and is selected by the
platform. Then the clocksource's Kconfig is changed to make this option
selectable by the user if the COMPILE_TEST option is set. Otherwise, it is
up to the platform's Kconfig to select the timer.
Due on the delay specific code, this driver will compile only on the ARM
architecture.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_PRIMA2_TIMER and is selected by the
platform. Then the clocksource's Kconfig is changed to make this option
selectable by the user if the COMPILE_TEST option is set. Otherwise, it is
up to the platform's Kconfig to select the timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_MXS_TIMER and is selected by the
platform. Then the clocksource's Kconfig is changed to make this option
selectable by the user if the COMPILE_TEST option is set. Otherwise, it is
up to the platform's Kconfig to select the timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_MOXART_TIMER and is selected by the
platform. Then the clocksource's Kconfig is changed to make this option
selectable by the user if the COMPILE_TEST option is set. Otherwise, it is
up to the platform's Kconfig to select the timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_ATLAS7_TIMER and is selected by the
platform. Then the clocksource's Kconfig is changed to make this option
selectable by the user if the COMPILE_TEST option is set. Otherwise, it is
up to the platform's Kconfig to select the timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_CLPS711X_TIMER and is selected by the
platform. Then the clocksource's Kconfig is changed to make this option
selectable by the user if the COMPILE_TEST option is set. Otherwise, it is
up to the platform's Kconfig to select the timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_BCM_KONA_TIMER and is selected by the
platform. Then the clocksource's Kconfig is changed to make this option
selectable by the user if the COMPILE_TEST option is set. Otherwise, it is
up to the platform's Kconfig to select the timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In order to increase the compilation test coverage, add the COMPILE_TEST
so the driver can be compiled even if it does not belong to the platform
or the architecture.
The io.h header inclusion is also added as it the driver does not compile
on UM platform.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_BCM2835_TIMER and is selected by the
platform. Then the clocksource's Kconfig is changed to make this option
selectable by the user if the COMPILE_TEST option is set. Otherwise, it
is up to the platform's Kconfig to select the timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
All the clocksource drivers's init function are now converted to return
an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the
clksrc-of table.
Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
For exynos_mct and samsung_pwm_timer:
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
For arch/arc:
Acked-by: Vineet Gupta <vgupta@synopsys.com>
For mediatek driver:
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
For the Rockchip-part
Acked-by: Heiko Stuebner <heiko@sntech.de>
For STi :
Acked-by: Patrice Chotard <patrice.chotard@st.com>
For the mps2-timer.c and versatile.c changes:
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
For the OXNAS part :
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
For LPC32xx driver:
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
For Broadcom Kona timer change:
Acked-by: Ray Jui <ray.jui@broadcom.com>
For Sun4i and Sun5i:
Acked-by: Chen-Yu Tsai <wens@csie.org>
For Meson6:
Acked-by: Carlo Caione <carlo@caione.org>
For Keystone:
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
For NPS:
Acked-by: Noam Camus <noamca@mellanox.com>
For bcm2835:
Acked-by: Eric Anholt <eric@anholt.net>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
The init functions do not return any error and let the caller unaware of
the state of the system.
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and leave the caller unaware of the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just returns an error code from the init function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init function does not return any error, it prints a message, returns and
lets the caller unaware if the state of the system.
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Ray Jui <ray.jui@broadcom.com>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Eric Anholt <eric@anholt.net>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Baruch Siach <baruch@tkos.co.il>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
on a rk3399-evb
Tested-by: Heiko Stuebner <heiko@sntech.de>
Currently, the clksrc-probe is not able to handle any error from the init
functions. There are different issues with the current code:
- the code is duplicated in the init functions by writing error
- every driver tends to panic in its own init function
- counting the number of clocksources is not reliable
This patch adds another table to store the functions returning an error.
The table is temporary while we convert all the drivers to return an error
and will disappear.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add clocksource and clockevent driver from dual RPS timer.
The HW provides a dual one-shot or periodic 24bit timers,
the drivers set the first one as tick event source and the
second as a continuous scheduler clock source.
The timer can use 1, 16 or 256 as pre-dividers, thus the
clocksource uses 16 by default.
CC: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The only difference between the rk3399 SoC and the other ones is the control
register offset which is different.
Add a new field to store the control register address depending on the SoC
and use it instead of the <base> + <control offset>.
Signed-off-by: Huang Tao <huangtao@rock-chips.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The rockchip timer is a broadcast timer. Add the CLOCK_EVT_FEAT_DYNIRQ flag
and set the cpumask to all possible cpus to save power by avoiding
unnecessary wakeups and IPIs.
Signed-off-by: Huang Tao <huangtao@rock-chips.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Correct the typo in "driver" word in the option description.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Fix the Samsung pwm timer access code to deal with kernels built for big
endian operation.
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Change the dc_timer function to be static as it is not used outside
this driver. This fixes the following warning:
drivers/clocksource/timer-digicolor.c:66:24: warning: symbol 'dc_timer' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Baruch Siach <baruch@tkos.co.il>
The driver does not export armada_370_xp_timer_syscore_ops so
make it static to fix the following warning:
drivers/clocksource/time-armada-370-xp.c:249:20: warning: symbol 'armada_370_xp_timer_syscore_ops' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
- x86: miscellaneous fixes, AVIC support (local APIC virtualization,
AMD version)
- s390: polling for interrupts after a VCPU goes to halted state is
now enabled for s390; use hardware provided information about facility
bits that do not need any hypervisor activity, and other fixes for
cpu models and facilities; improve perf output; floating interrupt
controller improvements.
- MIPS: miscellaneous fixes
- PPC: bugfixes only
- ARM: 16K page size support, generic firmware probing layer for
timer and GIC
Christoffer Dall (KVM-ARM maintainer) says:
"There are a few changes in this pull request touching things outside
KVM, but they should all carry the necessary acks and it made the
merge process much easier to do it this way."
though actually the irqchip maintainers' acks didn't make it into the
patches. Marc Zyngier, who is both irqchip and KVM-ARM maintainer,
later acked at http://mid.gmane.org/573351D1.4060303@arm.com
"more formally and for documentation purposes".
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXPJjyAAoJEL/70l94x66DhioH/j4fwQ0FmfPSM9PArzaFHQdx
LNE3tU4+bobbsy1BJr4DiAaOUQn3DAgwUvGLWXdeLiOXtoWXBiFHKaxlqEsCA6iQ
xcTH1TgfxsVoqGQ6bT9X/2GCx70heYpcWG3f+zqBy7ZfFmQykLAC/HwOr52VQL8f
hUFi3YmTHcnorp0n5Xg+9r3+RBS4D/kTbtdn6+KCLnPJ0RcgNkI3/NcafTemoofw
Tkv8+YYFNvKV13qlIfVqxMa0GwWI3pP6YaNKhaS5XO8Pu16HuuF1JthJsUBDzwBa
RInp8R9MoXgsBYhLpz3jc9vWG7G9yDl5LehsD9KOUGOaFYJ7sQN+QZOusa6jFgA=
=llO5
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Small release overall.
x86:
- miscellaneous fixes
- AVIC support (local APIC virtualization, AMD version)
s390:
- polling for interrupts after a VCPU goes to halted state is now
enabled for s390
- use hardware provided information about facility bits that do not
need any hypervisor activity, and other fixes for cpu models and
facilities
- improve perf output
- floating interrupt controller improvements.
MIPS:
- miscellaneous fixes
PPC:
- bugfixes only
ARM:
- 16K page size support
- generic firmware probing layer for timer and GIC
Christoffer Dall (KVM-ARM maintainer) says:
"There are a few changes in this pull request touching things
outside KVM, but they should all carry the necessary acks and it
made the merge process much easier to do it this way."
though actually the irqchip maintainers' acks didn't make it into the
patches. Marc Zyngier, who is both irqchip and KVM-ARM maintainer,
later acked at http://mid.gmane.org/573351D1.4060303@arm.com ('more
formally and for documentation purposes')"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (82 commits)
KVM: MTRR: remove MSR 0x2f8
KVM: x86: make hwapic_isr_update and hwapic_irr_update look the same
svm: Manage vcpu load/unload when enable AVIC
svm: Do not intercept CR8 when enable AVIC
svm: Do not expose x2APIC when enable AVIC
KVM: x86: Introducing kvm_x86_ops.apicv_post_state_restore
svm: Add VMEXIT handlers for AVIC
svm: Add interrupt injection via AVIC
KVM: x86: Detect and Initialize AVIC support
svm: Introduce new AVIC VMCB registers
KVM: split kvm_vcpu_wake_up from kvm_vcpu_kick
KVM: x86: Introducing kvm_x86_ops VCPU blocking/unblocking hooks
KVM: x86: Introducing kvm_x86_ops VM init/destroy hooks
KVM: x86: Rename kvm_apic_get_reg to kvm_lapic_get_reg
KVM: x86: Misc LAPIC changes to expose helper functions
KVM: shrink halt polling even more for invalid wakeups
KVM: s390: set halt polling to 80 microseconds
KVM: halt_polling: provide a way to qualify wakeups during poll
KVM: PPC: Book3S HV: Re-enable XICS fast path for irqfd-generated interrupts
kvm: Conditionally register IRQ bypass consumer
...
- Support for EZChip (now Mellanox) NPS-400 Network processor based on ARC700
http://www.mellanox.com/related-docs/prod_npu/PB_NPS-400.pdf
- NPS interrupt controller and clocksource drivers
- ARC timers probed off DT
- ARC iqrchips switching to linear domain (upgrade from legacy domains)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pnAx
-----END PGP SIGNATURE-----
Merge tag 'arc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"We have a relatively big changeset for ARC for 4.7.
The highlight is support for EZChip (now Mellanox) NPS-400 network
processor, a 400-Gb throughput C-programmable packet processor based
on ARC700 cores from Synopsys. See
http://www.mellanox.com/related-docs/prod_npu/PB_NPS-400.pdf
Also present are irqchip and clocksource drivers for NPS as agreed
with respective maintainers to go via ARC tree due to an soc header
dependency. I have the needed ACKs from Jason, Marc, Daniel. You
might run into a trivial merge conflict in drivers/irqchip/*
This EZChip platform support required some deep changes in ARC
architecture code and also opportunity to cleanup past sins (legacy
irq domains, missing irq domain lookup, hard coded timer irqs...)
Summary:
- Support for EZChip (now Mellanox) NPS-400 Network processor based
on ARC700
- NPS interrupt controller and clocksource drivers
- ARC timers probed off DT
- ARC iqrchips switching to linear domain (upgrade from legacy
domains)"
* tag 'arc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (37 commits)
arc: axs103_smp: Fix CPU frequency to 100MHz for dual-core
arc: axs10x: Add DT bindings for I2S PLL Clock
ARC: pae: STRICT_MM_TYPECHECKS was broken
ARC: Add eznps platform to Kconfig and Makefile
ARC: [plat-eznps] Use dedicated COMMAND_LINE_SIZE
ARC: [plat-eznps] Use dedicated cpu_relax()
ARC: [plat-eznps] Use dedicated identity auxiliary register.
ARC: [plat-eznps] Use dedicated SMP barriers
ARC: [plat-eznps] Use dedicated atomic/bitops/cmpxchg
ARC: [plat-eznps] Use dedicated user stack top
ARC: [plat-eznps] Add eznps platform
ARC: [plat-eznps] Add eznps board defconfig and dts
ARC: Mark secondary cpu online only after all HW setup is done
ARC: rwlock: disable interrupts in !LLSC variant
ARC: Make vmalloc size configurable
ARC: clean out UAPI byteorder.h clean off Kconfig symbol
irqchip: add nps Internal and external irqchips
clocksource: Add NPS400 timers driver
soc: Support for EZchip SoC
Documentation: Add EZchip vendor to binding list
...
Fu Wei