Pull x86 core updates from Ingo Molnar:
"There were so many changes in the x86/asm, x86/apic and x86/mm topics
in this cycle that the topical separation of -tip broke down somewhat -
so the result is a more traditional architecture pull request,
collected into the 'x86/core' topic.
The topics were still maintained separately as far as possible, so
bisectability and conceptual separation should still be pretty good -
but there were a handful of merge points to avoid excessive
dependencies (and conflicts) that would have been poorly tested in the
end.
The next cycle will hopefully be much more quiet (or at least will
have fewer dependencies).
The main changes in this cycle were:
* x86/apic changes, with related IRQ core changes: (Jiang Liu, Thomas
Gleixner)
- This is the second and most intrusive part of changes to the x86
interrupt handling - full conversion to hierarchical interrupt
domains:
[IOAPIC domain] -----
|
[MSI domain] --------[Remapping domain] ----- [ Vector domain ]
| (optional) |
[HPET MSI domain] ----- |
|
[DMAR domain] -----------------------------
|
[Legacy domain] -----------------------------
This now reflects the actual hardware and allowed us to distangle
the domain specific code from the underlying parent domain, which
can be optional in the case of interrupt remapping. It's a clear
separation of functionality and removes quite some duct tape
constructs which plugged the remap code between ioapic/msi/hpet
and the vector management.
- Intel IOMMU IRQ remapping enhancements, to allow direct interrupt
injection into guests (Feng Wu)
* x86/asm changes:
- Tons of cleanups and small speedups, micro-optimizations. This
is in preparation to move a good chunk of the low level entry
code from assembly to C code (Denys Vlasenko, Andy Lutomirski,
Brian Gerst)
- Moved all system entry related code to a new home under
arch/x86/entry/ (Ingo Molnar)
- Removal of the fragile and ugly CFI dwarf debuginfo annotations.
Conversion to C will reintroduce many of them - but meanwhile
they are only getting in the way, and the upstream kernel does
not rely on them (Ingo Molnar)
- NOP handling refinements. (Borislav Petkov)
* x86/mm changes:
- Big PAT and MTRR rework: making the code more robust and
preparing to phase out exposing direct MTRR interfaces to drivers -
in favor of using PAT driven interfaces (Toshi Kani, Luis R
Rodriguez, Borislav Petkov)
- New ioremap_wt()/set_memory_wt() interfaces to support
Write-Through cached memory mappings. This is especially
important for good performance on NVDIMM hardware (Toshi Kani)
* x86/ras changes:
- Add support for deferred errors on AMD (Aravind Gopalakrishnan)
This is an important RAS feature which adds hardware support for
poisoned data. That means roughly that the hardware marks data
which it has detected as corrupted but wasn't able to correct, as
poisoned data and raises an APIC interrupt to signal that in the
form of a deferred error. It is the OS's responsibility then to
take proper recovery action and thus prolonge system lifetime as
far as possible.
- Add support for Intel "Local MCE"s: upcoming CPUs will support
CPU-local MCE interrupts, as opposed to the traditional system-
wide broadcasted MCE interrupts (Ashok Raj)
- Misc cleanups (Borislav Petkov)
* x86/platform changes:
- Intel Atom SoC updates
... and lots of other cleanups, fixlets and other changes - see the
shortlog and the Git log for details"
* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (222 commits)
x86/hpet: Use proper hpet device number for MSI allocation
x86/hpet: Check for irq==0 when allocating hpet MSI interrupts
x86/mm/pat, drivers/infiniband/ipath: Use arch_phys_wc_add() and require PAT disabled
x86/mm/pat, drivers/media/ivtv: Use arch_phys_wc_add() and require PAT disabled
x86/platform/intel/baytrail: Add comments about why we disabled HPET on Baytrail
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
iommu, x86: Properly handle posted interrupts for IOMMU hotplug
iommu, x86: Provide irq_remapping_cap() interface
iommu, x86: Setup Posted-Interrupts capability for Intel iommu
iommu, x86: Add cap_pi_support() to detect VT-d PI capability
iommu, x86: Avoid migrating VT-d posted interrupts
iommu, x86: Save the mode (posted or remapped) of an IRTE
iommu, x86: Implement irq_set_vcpu_affinity for intel_ir_chip
iommu: dmar: Provide helper to copy shared irte fields
iommu: dmar: Extend struct irte for VT-d Posted-Interrupts
iommu: Add new member capability to struct irq_remap_ops
x86/asm/entry/64: Disentangle error_entry/exit gsbase/ebx/usermode code
x86/asm/entry/32: Shorten __audit_syscall_entry() args preparation
x86/asm/entry/32: Explain reloading of registers after __audit_syscall_entry()
...
When CONFIG_SND_HDA_I915=n, we get a compile warning:
sound/pci/hda/hda_intel.c: In function ‘azx_probe_continue’:
sound/pci/hda/hda_intel.c:1882:2: warning: label ‘skip_i915’ defined but not used [-Wunused-label]
Fix it by putting again ifdef to it. Sigh.
Fixes: bf06848bdb ('ALSA: hda - Continue probing even if i915 binding fails')
Reported-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new Dell XPS13 also requires the similar quirk for fixing the
noisy outputs. (But, as the codec was changed, now the fixup for
Latitude is used instead.)
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=99851
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We still got a report that the audio crackles and noises occur with
the recent 4.1 kernels on Dell machines. These machines seem to need
similar workarounds that have been applied to the recent Dell XPS 13
models. Since the codec of these machines (Dell Latitute E7240 and
E7440) is different from XPS 13's one, we need a new fixup entry.
Also, it was confirmed that the previous workaround to disable the
widget power-save (commit [219f47e4f964: ALSA: hda - Disable widget
power-saving for ALC292 & co]) is no longer needed after this fix.
So, this patch includes the partial revert of the commit, too.
Reported-and-tested-by: Mihai Donțu <mihai.dontu@gmail.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On a HP Envy TouchSmart laptop, there are 2 speakers (main speaker
and subwoofer speaker), 1 headphone and 2 DACs, without this fixup,
the headphone will be assigned to a DAC and the 2 speakers will be
assigned to another DAC, this assignment makes the surround-2.1
channels invalid.
To fix it, here using a DAC/pin preference map to bind the main
speaker to 1 DAC and the subwoofer speaker will be assigned to another
DAC.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The previous patch tried to continue the probe if i915 binding fails.
For for simplicity reason, we haven't implemented abort even for
controller chips that are dedicated for HDMI/DP on HSW and BDW.
However, Mengdong suggested that this can be dangerous; BIOS may
disable gfx power well although the PCI entry for HD-audio is left,
and this may result in the unexpected behavior, kernel errors, etc.
For avoiding this situation, abort the probe at i915 binding failure
only for HSW/BDW chips selectively. For other chips, it still
continues.
Fixes: bf06848bdb ('ALSA: hda - Continue probing even if i915 binding fails')
Reported-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Yet another regression by the transition to regmap cache; for better
usability, we had the fake mute control using the zero amp value for
Conexant codecs, and this was forgotten in the new hda core code.
Since the bits 4-7 are unused for the amp registers (as we follow the
syntax of AMP_GET verb), the bit 4 is now used to indicate the fake
mute. For setting this flag, snd_hda_codec_amp_update() becomes a
function from a simple macro. The bonus is that it gained a proper
function description.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently snd-hda-intel driver aborts the probing of Intel HD-audio
controller with i915 power well management when binding with i915
driver via hda_i915_init() fails. This is no big problem for Haswell
and Broadwell where the HD-audio controllers are dedicated to
HDMI/DP, thus i915 link is mandatory. However, Skylake, Baytrail and
Braswell have only one controller and both HDMI/DP and analog codecs
share the same bus. Thus, even if HDMI/DP isn't usable, we should
keep the controller working for other codecs.
For fixing this, this patch simply allows continuing the probing even
if hda_i915_init() call fails. This may leave stale sound components
for HDMI/DP devices that are unbound with graphics. We could abort
the probing selectively, but from the code simplicity POV, it's better
to continue in all cases.
Reported-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new regmap code seems to cache this, which isn't helpful
for the hotplug dock situation where this gets updated.
Use the uncached query for this.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Nothing in <asm/io.h> uses anything from <linux/vmalloc.h>, so
remove it from there and fix up the resulting build problems
triggered on x86 {64|32}-bit {def|allmod|allno}configs.
The breakages were triggering in places where x86 builds relied
on vmalloc() facilities but did not include <linux/vmalloc.h>
explicitly and relied on the implicit inclusion via <asm/io.h>.
Also add:
- <linux/init.h> to <linux/io.h>
- <asm/pgtable_types> to <asm/io.h>
... which were two other implicit header file dependencies.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[ Tidied up the changelog. ]
Acked-by: David Miller <davem@davemloft.net>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Colin Cross <ccross@android.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: James E.J. Bottomley <JBottomley@odin.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Suma Ramars <sramars@cisco.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acer Aspire 9420 with ALC883 (1025:0107) needs the fixup for EAPD to
make the sound working like other Aspire models.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94111
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VT202x codecs seem requiring some delay after the resume D0 power
transition for making the jack detection working again. Without the
delay soon after D0, the jack is always detected as unplugged.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98921
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [49fb18972581: ALSA: hda - Set stream_pm ops automatically
by generic parser] resulted in regressions on some Realtek and VIA
codecs because these drivers set patch_ops after calling the generic
parser, thus stream_pm got cleared to NULL again. I haven't noticed
since I tested with IDT codec.
Restore (partial revert) the stream_pm ops for them to fix the
regression.
Fixes: 49fb189725 ('ALSA: hda - Set stream_pm ops automatically by generic parser')
Reported-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When headphone mic boost is above zero, some 10 - 20 second delay
might occur before the headphone mic is operational.
Therefore disable the headphone mic boost control (recording gain is
sufficient even without it).
(Note: this patch is not about the headset mic, it's about the less
common mic-in only mode.)
BugLink: https://bugs.launchpad.net/bugs/1454235
Suggested-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got a regression report that 4.1-rc causes noises on a Dell
laptop. Similar like Realtek codec, this seems also triggered by the
recent power_save_node feature. As this kind of issue is quite hard
to debug without actual hardware, disable the power_save_node flag for
this codec as a workaround.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98971
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A new AMD controller [1002:aac8] seems to need the quirk for other AMD
NS HDMI stuff, otherwise it gives noisy sounds.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=99021
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This allows user to test power_save_node feature via sysfs or patch
firmware even on the codecs that don't specify it. It'll also save a
few lines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 7290006d8c.
Through the regression report, it was revealed that the
tpacpi_led_set() call to thinkpad_acpi helper doesn't only toggle the
mute LED but actually mutes the sound. This is contradiction to the
expectation, and rather confuses user.
According to Henrique, it's not trivial to judge which TP model
behaves "LED-only" and which model does whatever more intrusive, as
Lenovo's implementations vary model by model. So, from the safety
reason, we should revert the patch for now.
Reported-by: Martin Steigerwald <martin@lichtvoll.de>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got reports that ALC3226 (a Dell variant of ALC292) gives click
noises at transition from D3 to D0 when the widget power-saving is
enabled. Further debugging session showed that avoiding it isn't
trivial, unfortunately, since paths are basically activated
dynamically while the pins have been already enabled.
This patch disables the widget power-saving for such codecs.
Reported-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The widget (node) power-saves restore the widget states at each
transition from D3 to D0 on each node. This was added in the commit
[d545a57c5f84:ALSA: hda - Sync node attributes at resume from widget
power saving]. However, the test was rater false-positive; this
wasn't needed for any codecs.
Since the resync may take significant number of additional verbs to be
executed, it's better to reduce it. Let's disable it for now again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Lenovo ThinkPad L450 requires the ALC292_FIXUP_TPT440_DOCK fix in
order to get sound output on the docking stations audio port.
This patch was tested using a ThinkPad L450 (20DSS00B00) using kernel
4.0.3 and a ThinkPad Pro Dock.
Signed-off-by: Ansgar Hegerfeld <linux@hegerfeld.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for Conexant HD Audio codecs
CX20721, CX20722, CX20723 and CX20724.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1454656
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC662 does not need any special verbs to change the jack functionality,
and enables mic in through the headphone jack mode by changing the
direction of the headphone pin node.
BugLink: https://bugs.launchpad.net/bugs/1454235
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This enables the headset microphone on Dell Inspiron 5548,
or at least some variants of it.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1452175
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fujitsu Lifebook E752 laptop needs a similar quirk done for Lifebook
T731. Otherwise the headphone is always muted.
Reported-and-tested-by: Christian Weber <we_chris@hotmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Looks like audigy emu10k2 (probably emu10k1 - sb live too) support two
modes for DMA. Second mode is useful for 64 bit os with more then 2 GB
of ram (fixes problems with big soundfont loading)
1) 32MB from 2 GB address space using 8192 pages (used now as default)
2) 16MB from 4 GB address space using 4096 pages
Mode is set using HCFG_EXPANDED_MEM flag in HCFG register.
Also format of emu10k2 page table is then different.
Signed-off-by: Peter Zubaj <pzubaj@marticonet.sk>
Tested-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some models provide too long string for the shortname that has 32bytes
including the terminator, and it results in a non-terminated string
exposed to the user-space. This isn't too critical, though, as the
string is stopped at the succeeding longname string.
This patch fixes such entries by dropping "SB" prefix (it's enough to
fit within 32 bytes, so far). Meanwhile, it also changes strcpy()
with strlcpy() to make sure that this kind of problem won't happen in
future, too.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the missing flag to enable "Mute-LED Mode" mixer enum
ctl for Thinkpads that have also the software mute-LED control.
Reported-and-tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mute-LED mode control has the fixed on/off states that are
supposed to remain on/off regardless of the master switch. However,
this doesn't work actually because the vmaster hook is called in the
vmaster code itself.
This patch fixes it by calling the hook indirectly after checking the
mute LED mode.
Reported-and-tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dell XPS13 produces a click noise at boot up, and Gabriele spotted out
that it's triggered by the initial pin control of the mic (NID 0x19).
This has to be set to Hi-Z Vref while the driver initializes to Vref
80% as a normal mic.
This patch fixes the generic parser code not to override the target
vref if it has been already set by the driver, and adds a proper
initialization of the target vref for this pin in the Realtek driver
side.
Reported-and-tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Switch default pcbeep path to Line in path.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Tested-by: Hui Wang <hui.wang@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ALC256 does not have a mixer nid at 0x0b, and there's no
loopback path (the output pins are directly connected to the DACs).
This commit fixes an "num_steps = 0 for NID=0xb (ctl = Beep Playback Volume)"
error (and as a result, problems with amixer/alsamixer).
If there's pcbeep functionality, it certainly isn't controlled by setting an
amp on 0x0b, so disable beep functionality (at least for now).
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1446517
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch addes AZX_DCAPS_I915_POWERWELL to BYT (Baytrail).
Like Braswell and Skylake, the HDMI codec on Bytrail is also in the shared
power well with GPU. This power well must be turned on before we reset link
to probe the codec, to avoid communication failure with the codec.
The side effect is that this power is always ON in S0 because the BYT HDMI
codec does not support EPSS or D3ClkStop and so the controller doesn't enter
D3 at runtime, and the HDMI codec and analog codec share a single physical
HD-A link and so we cannot reset the HD-A link freely when we re-enable the
power to use the HDMI codec.
Next step is to test if an AGP reset or double AGP reset on BYT HDMI codec is
okay to bring the HDMI codec back to a functional state after restoring the
power. If okay, we can bind the power on/off with the HDMI codec PM without
interrupting the analog audio.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Only Intel Haswell and Broadwell have a separate HD-A controller (PCI device 3)
for display audio, which needs to get 24MHz HD-A link BCLK from the variable
display core clock through vendor specific registers EM4 & EM5. Other platforms
(Baytrail, Braswell and Skylake) don't have this feature.
So this patch checks the PCI device ID of the controller in haswell_set_bclk()
and only sync BCLK for HSW and BDW.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Muting the headphone output pin right before the codec suspension
prevents pop noises when headphones are plugged in (except for a
barely audible click noise).
This solution allows to truly save some power when headphones are
plugged in unlike the previous solution (033b0a7ca9c:
"ALSA: hda - Pop noises fix for XPS13 9333")
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This function is a bit unusual because it accepts negative values as
"conn_len". It's theoretically possible for both "cache_len" and
"conn_len" to be -ENOSPC and in that case we would oops trying to run
memcmp() on the uninitialized "list" pointer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [a551d91473e5: ALSA: hda - Use regmap for command verb
caches, too] introduced a regression due to a typo in the conversion;
the IEC958 status bits of slave digital devices aren't updated
correctly. This patch corrects it.
Fixes: a551d91473 ('ALSA: hda - Use regmap for command verb caches, too')
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
DEVICE_ALI previously would jump to port_inited after calling
pci_iomap(), bypassing the check for bmaddr being NULL.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Because AZX_DCAPS_PM_RUNTIME is always defined as non-zero, the
initial part of the expression can be skipped.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Lenovo Thinkpad T450 requires the ALC292_FIXUP_TPT440_DOCK as well in
order to get working sound output on the docking stations headphone jack.
Patch tested on a Thinkpad T450 (20BVCTO1WW) using kernel 4.0-rc7 in
conjunction with a ThinkPad Ultradock.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The optical ports on the E-mu 1010 (and dock) can be configured
for ADAT- or S/PDIF-mode, which is currently hardcoded to ADAT.
Add two mixer elements to expose this setting.
Tested on an E-mu 1010 PCIe with connected Micro Dock.
Signed-off-by: Michael Gernoth <michael@gernoth.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the dock on an E-mu 1010 card is disconnected, all outputs get
muted by the hardware. Add logic to detect a disconnect and unmute.
Signed-off-by: Michael Gernoth <michael@gernoth.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds