Allow setting of TX and RX antennas configuration via nl80211.
The antenna configuration is defined as a bitmap of allowed antennas to use.
This API can be used to mask out antennas which are not attached or should not
be used for other reasons like regulatory concerns or special setups.
Separate bitmaps are used for RX and TX to allow configuring different antennas
for receiving and transmitting. Each bitmap is 32 bit long, each bit
representing one antenna, starting with antenna 1 at the first bit. If an
antenna bit is set, this means the driver is allowed to use this antenna for RX
or TX respectively; if the bit is not set the hardware is not allowed to use
this antenna.
Using bitmaps has the benefit of allowing for a flexible configuration
interface which can support many different configurations and which can be used
for 802.11n as well as non-802.11n devices. Instead of relying on some hardware
specific assumptions, drivers can use this information to know which antennas
are actually attached to the system and derive their capabilities based on
that.
802.11n devices should enable or disable chains, based on which antennas are
present (If all antennas belonging to a particular chain are disabled, the
entire chain should be disabled). HT capabilities (like STBC, TX Beamforming,
Antenna selection) should be calculated based on the available chains after
applying the antenna masks. Should a 802.11n device have diversity antennas
attached to one of their chains, diversity can be enabled or disabled based on
the antenna information.
Non-802.11n drivers can use the antenna masks to select RX and TX antennas and
to enable or disable antenna diversity.
While covering chainmasks for 802.11n and the standard "legacy" modes "fixed
antenna 1", "fixed antenna 2" and "diversity" this API also allows more rare,
but useful configurations as follows:
1) Send on antenna 1, receive on antenna 2 (or vice versa). This can be used to
have a low gain antenna for TX in order to keep within the regulatory
constraints and a high gain antenna for RX in order to receive weaker signals
("speak softly, but listen harder"). This can be useful for building long-shot
outdoor links. Another usage of this setup is having a low-noise pre-amplifier
on antenna 1 and a power amplifier on the other antenna. This way transmit
noise is mostly kept out of the low noise receive channel.
(This would be bitmaps: tx 1 rx 2).
2) Another similar setup is: Use RX diversity on both antennas, but always send
on antenna 1. Again that would allow us to benefit from a higher gain RX
antenna, while staying within the legal limits.
(This would be: tx 0 rx 3).
3) And finally there can be special experimental setups in research and
development even with pre 802.11n hardware where more than 2 antennas are
available. It's good to keep the API simple, yet flexible.
Signed-off-by: Bruno Randolf <br1@einfach.org>
--
v7: Made bitmasks 32 bit wide and rebased to latest wireless-testing.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using %pV reduces the number of printk calls and
eliminates any possible message interleaving from
other printk calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using %pV reduces the number of printk calls and
eliminates any possible message interleaving from
other printk calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using %pV reduces the number of printk calls and
eliminates any possible message interleaving from
other printk calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BCM4320a devices seem to sometimes do scanning pretty poorly. This can be
workaround by issuing new scan every second, while not yet connected. By this
new scanning method device catches beacons much faster. Fixes bug #20822.
Reported-by: Luís Picciochi <Pitxyoki@gmail.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BCM4320a devices do not return bss for currently connected AP in bss-list,
althought this is required by NDIS specs. Missing bss leads to warning at
net/wireless/sme.c:__cfg80211_connect_result(), WARN_ON(!bss).
Workaround this by crafting bss manually with information we can read from
device. Workaround is only used when device bss-list does not return current
bss, and so is only used with BCM4320a devices and not newer BCM4320b ones.
Fixes bug #20152.
Reported-by: Luís Picciochi <Pitxyoki@gmail.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The lower driver is notified when the fragmentation threshold changes
and upon a reconfig of the interface.
If the driver supports hardware TX fragmentation, don't fragment
packets in the stack.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This eliminates compiler warnings by doing things how the
firmware class expects.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a firmware loading state machine to manage the process
of loading firmware asynchronously and completing initialization
upon success. The state machine attempts to load the preferred
firmware image. If that fails, and if an alternative firmware
image is available, it will attempt to load that one.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AP firmware specifies an API version in the GET_HW_SPEC
command response. Currently, the driver only supports AP
firmware for the 8366, and only supports API v1. In the future,
if higher API version firmwares emerge (possibly for different
chips), different ops can be selected based on the reported API
version.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mwl8k can operate in AP or STA mode, depending on the
firmware image that is loaded. By default, STA firmware is
loaded. Allow the user to override this default mode at
module load time. This saves an unnecessary firmware reload
for users only interested in AP mode.
Also, the firmware image can be swapped to meet the user's
add_interface request. For example, suppose the STA
firmware is loaded, no STA interface has been added, and the
user adds an AP interface. In this case, the AP firmware
will be loaded to meet the request.
Based on contributions from Pradeep Nemavat <pnemavat@marvell.com>,
Yogesh Powar <yogeshp@marvell.com>, and
Lennert Buytenhek <buytenh@wantstofly.org>.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is in preparation for supporting different fw images for
different interface types, and for supporting asynchronous
firmware loading.
Based on a patch from Pradeep Nemavat <pnemavat@marvell.com>
and Yogesh Powar <yogeshp@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
APIv1 AP firmware does not support the RF_TX_POWER command. It
supports the similar TX_POWER command.
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts change 783391c443728febc669e40597193308460e7b4f.
The stabilized AP v1 firmware uses the same tx descriptor as
the STA firmware.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Certain firmware versions, particularly the 8388 found on the XO-1,
do not support the EHS_REMOVE_WAKEUP command that is used to disable
WOL. Sending this command to the card will return a failure that
would get propagated up the stack and cause suspend to fail.
Instead, fall back to an all-zero wakeup mask.
This fixes http://dev.laptop.org/ticket/9967
Signed-off-by: Deepak Saxena <dsaxena@laptop.org>
Signed-off-by: Daniel Drake <dsd@laptop.org>
[includes fixups by Paul Fox]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This hunk added by commit 66fceb69b7 seems erroneous. We don't want to
prevent suspend of the whole system if no wakeup params are set.
In the case of the usb8388 we do want to keep the card powered up even
if there are no wakeup params. This is because it will continue acting
as a mesh node.
If the mesh is disabled, it would indeed make more sense to power down
the card during suspend, as the equivalent hunk does for the SD interface.
But that's a separate task; for now just restore the previous behaviour.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces the handcrafted
sign extension cruft with a generic
bitop function.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves code out from wireless drivers where two different
functions are defined in three code locations for the same purpose and
provides a common function to sign extend a 32-bit value.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use the newly added method to pass platform data for wl1251 too.
This allows to eliminate some redundant code.
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add runtime PM support, similar to how it's done for wl1271.
This allows to power down the card when the driver is loaded but
network is not in use.
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Call interface specific power callback before calling board specific
one. Also allow that callback to fail. This is how it's done for
wl1271 and will be used for runtime_pm support.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 6000 series devices and up, enable automatic update MAC's register
for better power usage in PSP mode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disconnected antenna algorithm is used to find out which antennas are
disconnected. It should be disabled for devices that support advanced
bluetooth coexist.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disconnected antenna algorithm is seperated into its own function from chain noise
calibration routine for better code management.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the HT information is changed due to
BSS changes (like legacy stations joining)
we need to recalculate HT RXON parameters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During the RXON rewrite, this code got lost.
When we've just associated, we need to enable
all calibrations and see if some were already
finished. Add back the missing code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RXON rework resulted in a massive loss of
throughput because we weren't programming the
device completely correctly -- the BSSID has
to be programmed into the device before the
AP station is uploaded. To fix this, simply
always send the unassoc RXON, i.e. even when
it was already unassoc so that the BSSID and
some other parameters are updated properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Garen noticed that this was wrong. Fix
the calibration -- default to multiple
chains and fall back to single where
possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: Fix WMM driver queue configuration"
inadvertedly broke iwlwifi, because now mac80211
configures the QoS settings before assoc, and
therefore before HT. Thus, iwlwifi no longer told
the device about the HT setting, which it needs
to -- and thus throughput went down a lot. Fix
this by resending the QoS command to the device
not only when QoS/WMM settings change, but also
when HT changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In iwl_rx_queue_update_write_ptr function
replace iwl_write_direct32 with iwl_write32 when not in power save mode.
We don't have to go through grab nic access as the NIC is already awake.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Legacy (4965 and 3945) devices has different tx_cmd_protection routine.
Move to iwl-legacy.c
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were two type of isr supported by iwlwifi devices.
legacy isr - only used by legacy devices (3945 & 4965)
ict isr - used by all new generation of iwlwifi devices
Move all the isr related functions into ops, the ict type of isr
supports only needed for newer devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move iwl_isr_legacy function to iwl_legacy.c since it only used
by legacy devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When building 4965 without 5000+ there were a
lot of build errors due to functions being used
that weren't even compiled in. To fix this move
some code around and only compile the HCMD code
for 5000+ series as it's not used for 4965.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the supported PCI ID list for 100 series devices
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the supported PCI ID list for 6000g2a series devices
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the supported PCI ID list for 6000g2b series devices
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debugfs code for ath5k was printing some unsigned int
stats with %d instead of %u. This meant that you could see
negative numbers instead of a clean wrap.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add watchdog functions for managing the Queues inside the hardware.
Normally the driver doesn't have much to do with these queues
directly, but the Ralink drivers did implement watchdog functions
for these. These watchdog functions are not triggered that often,
compared to the other watchdog functions, but I have at least
seen them trigger once or twice during a long stresstest run.
v2: Add extra documentation for register fields
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of the queue refactoring, the rt2x00lib_toggle_rx
can be removed and replaced with the call directly to
the set_device_state callback function.
We can remove the STATE_RADIO_RX_ON_LINK and
STATE_RADIO_RX_OFF_LINK, as it was only used for
special behavior inside rt2x00lib rather then the
drivers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue_entry argument to rt2x00queue_kick_tx_queue,
doesn't make sense due to the function name (it is called
kick QUEUE)... But neither do we need the queue_entry, since
we need the data_queue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue->lock is only used to protect the index
numbers. Rename the lock accordingly.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt73usb.c:43: ERROR: do not initialise statics to 0 or NULL
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00queue.c:804: ERROR: space prohibited after that open parenthesis '('
rt2x00queue.c:805: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00link.c:70: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00lib.h:60: ERROR: space prohibited after that open parenthesis '('
rt2x00lib.h:60: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00dev.c:689: ERROR: spaces required around that '=' (ctx:WxV)
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00config.c:136: ERROR: space required before the open parenthesis '('
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf