When programs need to calculate the csum from scratch for small UDP
packets and use bpf_l4_csum_replace() to feed the result from helpers
like bpf_csum_diff(), then we need a flag besides BPF_F_MARK_MANGLED_0
that would ignore the case of current csum being 0, and which would
still allow for the helper to set the csum and transform when needed
to CSUM_MANGLED_0.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This trie implements a longest prefix match algorithm that can be used
to match IP addresses to a stored set of ranges.
Internally, data is stored in an unbalanced trie of nodes that has a
maximum height of n, where n is the prefixlen the trie was created
with.
Tries may be created with prefix lengths that are multiples of 8, in
the range from 8 to 2048. The key used for lookup and update operations
is a struct bpf_lpm_trie_key, and the value is a uint64_t.
The code carries more information about the internal implementation.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a simple helper with the same semantics of strncpy_from_unsafe():
int bpf_probe_read_str(void *dst, int size, const void *unsafe_addr)
This gives more flexibility to a bpf program. A typical use case is
intercepting a file name during sys_open(). The current approach is:
SEC("kprobe/sys_open")
void bpf_sys_open(struct pt_regs *ctx)
{
char buf[PATHLEN]; // PATHLEN is defined to 256
bpf_probe_read(buf, sizeof(buf), ctx->di);
/* consume buf */
}
This is suboptimal because the size of the string needs to be estimated
at compile time, causing more memory to be copied than often necessary,
and can become more problematic if further processing on buf is done,
for example by pushing it to userspace via bpf_perf_event_output(),
since the real length of the string is unknown and the entire buffer
must be copied (and defining an unrolled strnlen() inside the bpf
program is a very inefficient and unfeasible approach).
With the new helper, the code can easily operate on the actual string
length rather than the buffer size:
SEC("kprobe/sys_open")
void bpf_sys_open(struct pt_regs *ctx)
{
char buf[PATHLEN]; // PATHLEN is defined to 256
int res = bpf_probe_read_str(buf, sizeof(buf), ctx->di);
/* consume buf, for example push it to userspace via
* bpf_perf_event_output(), but this time we can use
* res (the string length) as event size, after checking
* its boundaries.
*/
}
Another useful use case is when parsing individual process arguments or
individual environment variables navigating current->mm->arg_start and
current->mm->env_start: using this helper and the return value, one can
quickly iterate at the right offset of the memory area.
The code changes simply leverage the already existent
strncpy_from_unsafe() kernel function, which is safe to be called from a
bpf program as it is used in bpf_trace_printk().
Signed-off-by: Gianluca Borello <g.borello@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows XDP prog to extend/remove the packet
data at the head (like adding or removing header). It is
done by adding a new XDP helper bpf_xdp_adjust_head().
It also renames bpf_helper_changes_skb_data() to
bpf_helper_changes_pkt_data() to better reflect
that XDP prog does not work on skb.
This patch adds one "xdp_adjust_head" bit to bpf_prog for the
XDP-capable driver to check if the XDP prog requires
bpf_xdp_adjust_head() support. The driver can then decide
to error out during XDP_SETUP_PROG.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add socket family, type and protocol to bpf_sock allowing bpf programs
read-only access.
Add __sk_flags_offset[0] to struct sock before the bitfield to
programmtically determine the offset of the unsigned int containing
protocol and type.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new cgroup based program type, BPF_PROG_TYPE_CGROUP_SOCK. Similar to
BPF_PROG_TYPE_CGROUP_SKB programs can be attached to a cgroup and run
any time a process in the cgroup opens an AF_INET or AF_INET6 socket.
Currently only sk_bound_dev_if is exported to userspace for modification
by a bpf program.
This allows a cgroup to be configured such that AF_INET{6} sockets opened
by processes are automatically bound to a specific device. In turn, this
enables the running of programs that do not support SO_BINDTODEVICE in a
specific VRF context / L3 domain.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Registers new BPF program types which correspond to the LWT hooks:
- BPF_PROG_TYPE_LWT_IN => dst_input()
- BPF_PROG_TYPE_LWT_OUT => dst_output()
- BPF_PROG_TYPE_LWT_XMIT => lwtunnel_xmit()
The separate program types are required to differentiate between the
capabilities each LWT hook allows:
* Programs attached to dst_input() or dst_output() are restricted and
may only read the data of an skb. This prevent modification and
possible invalidation of already validated packet headers on receive
and the construction of illegal headers while the IP headers are
still being assembled.
* Programs attached to lwtunnel_xmit() are allowed to modify packet
content as well as prepending an L2 header via a newly introduced
helper bpf_skb_change_head(). This is safe as lwtunnel_xmit() is
invoked after the IP header has been assembled completely.
All BPF programs receive an skb with L3 headers attached and may return
one of the following error codes:
BPF_OK - Continue routing as per nexthop
BPF_DROP - Drop skb and return EPERM
BPF_REDIRECT - Redirect skb to device as per redirect() helper.
(Only valid in lwtunnel_xmit() context)
The return codes are binary compatible with their TC_ACT_
relatives to ease compatibility.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the bpf(2) syscall by two new commands, BPF_PROG_ATTACH and
BPF_PROG_DETACH which allow attaching and detaching eBPF programs
to a target.
On the API level, the target could be anything that has an fd in
userspace, hence the name of the field in union bpf_attr is called
'target_fd'.
When called with BPF_ATTACH_TYPE_CGROUP_INET_{E,IN}GRESS, the target is
expected to be a valid file descriptor of a cgroup v2 directory which
has the bpf controller enabled. These are the only use-cases
implemented by this patch at this point, but more can be added.
If a program of the given type already exists in the given cgroup,
the program is swapped automically, so userspace does not have to drop
an existing program first before installing a new one, which would
otherwise leave a gap in which no program is attached.
For more information on the propagation logic to subcgroups, please
refer to the bpf cgroup controller implementation.
The API is guarded by CAP_NET_ADMIN.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This program type is similar to BPF_PROG_TYPE_SOCKET_FILTER, except that
it does not allow BPF_LD_[ABS|IND] instructions and hooks up the
bpf_skb_load_bytes() helper.
Programs of this type will be attached to cgroups for network filtering
and accounting.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a LRU version of the existing BPF_MAP_TYPE_PERCPU_HASH
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a LRU version of the existing BPF_MAP_TYPE_HASH.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The verifier currently prints raw function ids when printing CALL
instructions or when complaining:
5: (85) call 23
unknown func 23
print a meaningful function name instead:
5: (85) call bpf_redirect#23
unknown func bpf_redirect#23
Moves the function documentation to a single comment and renames all
helpers names in the list to conform to the bpf_ prefix notation so
they can be greped in the kernel source.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use case is mainly for soreuseport to select sockets for the local
numa node, but since generic, lets also add this for other networking
and tracing program types.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a small helper that complements 36bbef52c7 ("bpf: direct packet
write and access for helpers for clsact progs") for invalidating the
current skb->hash after mangling on headers via direct packet write.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work implements direct packet access for helpers and direct packet
write in a similar fashion as already available for XDP types via commits
4acf6c0b84 ("bpf: enable direct packet data write for xdp progs") and
6841de8b0d ("bpf: allow helpers access the packet directly"), and as a
complementary feature to the already available direct packet read for tc
(cls/act) programs.
For enabling this, we need to introduce two helpers, bpf_skb_pull_data()
and bpf_csum_update(). The first is generally needed for both, read and
write, because they would otherwise only be limited to the current linear
skb head. Usually, when the data_end test fails, programs just bail out,
or, in the direct read case, use bpf_skb_load_bytes() as an alternative
to overcome this limitation. If such data sits in non-linear parts, we
can just pull them in once with the new helper, retest and eventually
access them.
At the same time, this also makes sure the skb is uncloned, which is, of
course, a necessary condition for direct write. As this needs to be an
invariant for the write part only, the verifier detects writes and adds
a prologue that is calling bpf_skb_pull_data() to effectively unclone the
skb from the very beginning in case it is indeed cloned. The heuristic
makes use of a similar trick that was done in 233577a220 ("net: filter:
constify detection of pkt_type_offset"). This comes at zero cost for other
programs that do not use the direct write feature. Should a program use
this feature only sparsely and has read access for the most parts with,
for example, drop return codes, then such write action can be delegated
to a tail called program for mitigating this cost of potential uncloning
to a late point in time where it would have been paid similarly with the
bpf_skb_store_bytes() as well. Advantage of direct write is that the
writes are inlined whereas the helper cannot make any length assumptions
and thus needs to generate a call to memcpy() also for small sizes, as well
as cost of helper call itself with sanity checks are avoided. Plus, when
direct read is already used, we don't need to cache or perform rechecks
on the data boundaries (due to verifier invalidating previous checks for
helpers that change skb->data), so more complex programs using rewrites
can benefit from switching to direct read plus write.
For direct packet access to helpers, we save the otherwise needed copy into
a temp struct sitting on stack memory when use-case allows. Both facilities
are enabled via may_access_direct_pkt_data() in verifier. For now, we limit
this to map helpers and csum_diff, and can successively enable other helpers
where we find it makes sense. Helpers that definitely cannot be allowed for
this are those part of bpf_helper_changes_skb_data() since they can change
underlying data, and those that write into memory as this could happen for
packet typed args when still cloned. bpf_csum_update() helper accommodates
for the fact that we need to fixup checksum_complete when using direct write
instead of bpf_skb_store_bytes(), meaning the programs can use available
helpers like bpf_csum_diff(), and implement csum_add(), csum_sub(),
csum_block_add(), csum_block_sub() equivalents in eBPF together with the
new helper. A usage example will be provided for iproute2's examples/bpf/
directory.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce BPF_PROG_TYPE_PERF_EVENT programs that can be attached to
HW and SW perf events (PERF_TYPE_HARDWARE and PERF_TYPE_SOFTWARE
correspondingly in uapi/linux/perf_event.h)
The program visible context meta structure is
struct bpf_perf_event_data {
struct pt_regs regs;
__u64 sample_period;
};
which is accessible directly from the program:
int bpf_prog(struct bpf_perf_event_data *ctx)
{
... ctx->sample_period ...
... ctx->regs.ip ...
}
The bpf verifier rewrites the accesses into kernel internal
struct bpf_perf_event_data_kern which allows changing
struct perf_sample_data without affecting bpf programs.
New fields can be added to the end of struct bpf_perf_event_data
in the future.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds a bpf_skb_change_tail() helper for tc BPF programs. The
basic idea is to expand or shrink the skb in a controlled manner. The
eBPF program can then rewrite the rest via helpers like bpf_skb_store_bytes(),
bpf_lX_csum_replace() and others rather than passing a raw buffer for
writing here.
bpf_skb_change_tail() is really a slow path helper and intended for
replies with f.e. ICMP control messages. Concept is similar to other
helpers like bpf_skb_change_proto() helper to keep the helper without
protocol specifics and let the BPF program mangle the remaining parts.
A flags field has been added and is reserved for now should we extend
the helper in future.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
While hashing out BPF's current_task_under_cgroup helper bits, it came
to discussion that the skb_in_cgroup helper name was suboptimally chosen.
Tejun says:
So, I think in_cgroup should mean that the object is in that
particular cgroup while under_cgroup in the subhierarchy of that
cgroup. Let's rename the other subhierarchy test to under too. I
think that'd be a lot less confusing going forward.
[...]
It's more intuitive and gives us the room to implement the real
"in" test if ever necessary in the future.
Since this touches uapi bits, we need to change this as long as v4.8
is not yet officially released. Thus, change the helper enum and rename
related bits.
Fixes: 4a482f34af ("cgroup: bpf: Add bpf_skb_in_cgroup_proto")
Reference: http://patchwork.ozlabs.org/patch/658500/
Suggested-by: Sargun Dhillon <sargun@sargun.me>
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
This adds a bpf helper that's similar to the skb_in_cgroup helper to check
whether the probe is currently executing in the context of a specific
subset of the cgroupsv2 hierarchy. It does this based on membership test
for a cgroup arraymap. It is invalid to call this in an interrupt, and
it'll return an error. The helper is primarily to be used in debugging
activities for containers, where you may have multiple programs running in
a given top-level "container".
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows user memory to be written to during the course of a kprobe.
It shouldn't be used to implement any kind of security mechanism
because of TOC-TOU attacks, but rather to debug, divert, and
manipulate execution of semi-cooperative processes.
Although it uses probe_kernel_write, we limit the address space
the probe can write into by checking the space with access_ok.
We do this as opposed to calling copy_to_user directly, in order
to avoid sleeping. In addition we ensure the threads's current fs
/ segment is USER_DS and the thread isn't exiting nor a kernel thread.
Given this feature is meant for experiments, and it has a risk of
crashing the system, and running programs, we print a warning on
when a proglet that attempts to use this helper is installed,
along with the pid and process name.
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP enabled drivers must transmit received packets back out on the same
port they were received on when a program returns this action.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new bpf prog type that is intended to run in early stages of the
packet rx path. Only minimal packet metadata will be available, hence a
new context type, struct xdp_md, is exposed to userspace. So far only
expose the packet start and end pointers, and only in read mode.
An XDP program must return one of the well known enum values, all other
return codes are reserved for future use. Unfortunately, this
restriction is hard to enforce at verification time, so take the
approach of warning at runtime when such programs are encountered. Out
of bounds return codes should alias to XDP_ABORTED.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work addresses a couple of issues bpf_skb_event_output()
helper currently has: i) We need two copies instead of just a
single one for the skb data when it should be part of a sample.
The data can be non-linear and thus needs to be extracted via
bpf_skb_load_bytes() helper first, and then copied once again
into the ring buffer slot. ii) Since bpf_skb_load_bytes()
currently needs to be used first, the helper needs to see a
constant size on the passed stack buffer to make sure BPF
verifier can do sanity checks on it during verification time.
Thus, just passing skb->len (or any other non-constant value)
wouldn't work, but changing bpf_skb_load_bytes() is also not
the proper solution, since the two copies are generally still
needed. iii) bpf_skb_load_bytes() is just for rather small
buffers like headers, since they need to sit on the limited
BPF stack anyway. Instead of working around in bpf_skb_load_bytes(),
this work improves the bpf_skb_event_output() helper to address
all 3 at once.
We can make use of the passed in skb context that we have in
the helper anyway, and use some of the reserved flag bits as
a length argument. The helper will use the new __output_custom()
facility from perf side with bpf_skb_copy() as callback helper
to walk and extract the data. It will pass the data for setup
to bpf_event_output(), which generates and pushes the raw record
with an additional frag part. The linear data used in the first
frag of the record serves as programmatically defined meta data
passed along with the appended sample.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
over time there were multiple requests to access different data
structures and fields of task_struct current, so finally add
the helper to access 'current' as-is. Tracing bpf programs will do
the rest of walking the pointers via bpf_probe_read().
Note that current can be null and bpf program has to deal it with,
but even dumb passing null into bpf_probe_read() is still safe.
Suggested-by: Brendan Gregg <brendan.d.gregg@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_clear_hash() was invoked due to mangling of relevant headers and
BPF program needs skb->hash later on, we can add a helper to trigger hash
recalculation via bpf_get_hash_recalc().
The helper will return the newly retrieved hash directly, but later access
can also be done via skb context again through skb->hash directly (inline)
without needing to call the helper once more.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a bpf helper, bpf_skb_in_cgroup, to decide if a skb->sk
belongs to a descendant of a cgroup2. It is similar to the
feature added in netfilter:
commit c38c4597e4 ("netfilter: implement xt_cgroup cgroup2 path match")
The user is expected to populate a BPF_MAP_TYPE_CGROUP_ARRAY
which will be used by the bpf_skb_in_cgroup.
Modifications to the bpf verifier is to ensure BPF_MAP_TYPE_CGROUP_ARRAY
and bpf_skb_in_cgroup() are always used together.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a BPF_MAP_TYPE_CGROUP_ARRAY and its bpf_map_ops's implementations.
To update an element, the caller is expected to obtain a cgroup2 backed
fd by open(cgroup2_dir) and then update the array with that fd.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds a helper for changing skb->pkt_type in a controlled way.
We only allow a subset of possible values and can extend that in future
should other use cases come up. Doing this as a helper has the advantage
that errors can be handeled gracefully and thus helper kept extensible.
It's a write counterpart to pkt_type member we can already read from
struct __sk_buff context. Major use case is to change incoming skbs to
PACKET_HOST in a programmatic way instead of having to recirculate via
redirect(..., BPF_F_INGRESS), for example.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a minimal helper for doing the groundwork of changing
the skb->protocol in a controlled way. Currently supported is v4 to
v6 and vice versa transitions, which allows f.e. for a minimal, static
nat64 implementation where applications in containers that still
require IPv4 can be transparently operated in an IPv6-only environment.
For example, host facing veth of the container can transparently do
the transitions in a programmatic way with the help of clsact qdisc
and cls_bpf.
Idea is to separate concerns for keeping complexity of the helper
lower, which means that the programs utilize bpf_skb_change_proto(),
bpf_skb_store_bytes() and bpf_lX_csum_replace() to get the job done,
instead of doing everything in a single helper (and thus partially
duplicating helper functionality). Also, bpf_skb_change_proto()
shouldn't need to deal with raw packet data as this is done by other
helpers.
bpf_skb_proto_6_to_4() and bpf_skb_proto_4_to_6() unclone the skb to
operate on a private one, push or pop additionally required header
space and migrate the gso/gro meta data from the shared info. We do
mark the gso type as dodgy so that headers are checked and segs
recalculated by the gso/gro engine. The gso_size target is adapted
as well. The flags argument added is currently reserved and can be
used for future extensions.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow-up commit to 1e33759c78 ("bpf, trace: add BPF_F_CURRENT_CPU
flag for bpf_perf_event_output") to add the same functionality into
bpf_perf_event_read() helper. The split of index into flags and index
component is also safe here, since such large maps are rejected during
map allocation time.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extended BPF carried over two instructions from classic to access
packet data: LD_ABS and LD_IND. They're highly optimized in JITs,
but due to their design they have to do length check for every access.
When BPF is processing 20M packets per second single LD_ABS after JIT
is consuming 3% cpu. Hence the need to optimize it further by amortizing
the cost of 'off < skb_headlen' over multiple packet accesses.
One option is to introduce two new eBPF instructions LD_ABS_DW and LD_IND_DW
with similar usage as skb_header_pointer().
The kernel part for interpreter and x64 JIT was implemented in [1], but such
new insns behave like old ld_abs and abort the program with 'return 0' if
access is beyond linear data. Such hidden control flow is hard to workaround
plus changing JITs and rolling out new llvm is incovenient.
Therefore allow cls_bpf/act_bpf program access skb->data directly:
int bpf_prog(struct __sk_buff *skb)
{
struct iphdr *ip;
if (skb->data + sizeof(struct iphdr) + ETH_HLEN > skb->data_end)
/* packet too small */
return 0;
ip = skb->data + ETH_HLEN;
/* access IP header fields with direct loads */
if (ip->version != 4 || ip->saddr == 0x7f000001)
return 1;
[...]
}
This solution avoids introduction of new instructions. llvm stays
the same and all JITs stay the same, but verifier has to work extra hard
to prove safety of the above program.
For XDP the direct store instructions can be allowed as well.
The skb->data is NET_IP_ALIGNED, so for common cases the verifier can check
the alignment. The complex packet parsers where packet pointer is adjusted
incrementally cannot be tracked for alignment, so allow byte access in such cases
and misaligned access on architectures that define efficient_unaligned_access
[1] https://git.kernel.org/cgit/linux/kernel/git/ast/bpf.git/?h=ld_abs_dw
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a BPF_F_CURRENT_CPU flag to optimize the use-case where user space has
per-CPU ring buffers and the eBPF program pushes the data into the current
CPU's ring buffer which saves us an extra helper function call in eBPF.
Also, make sure to properly reserve the remaining flags which are not used.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
introduce BPF_PROG_TYPE_TRACEPOINT program type and allow it to be attached
to the perf tracepoint handler, which will copy the arguments into
the per-cpu buffer and pass it to the bpf program as its first argument.
The layout of the fields can be discovered by doing
'cat /sys/kernel/debug/tracing/events/sched/sched_switch/format'
prior to the compilation of the program with exception that first 8 bytes
are reserved and not accessible to the program. This area is used to store
the pointer to 'struct pt_regs' which some of the bpf helpers will use:
+---------+
| 8 bytes | hidden 'struct pt_regs *' (inaccessible to bpf program)
+---------+
| N bytes | static tracepoint fields defined in tracepoint/format (bpf readonly)
+---------+
| dynamic | __dynamic_array bytes of tracepoint (inaccessible to bpf yet)
+---------+
Not that all of the fields are already dumped to user space via perf ring buffer
and broken application access it directly without consulting tracepoint/format.
Same rule applies here: static tracepoint fields should only be accessed
in a format defined in tracepoint/format. The order of fields and
field sizes are not an ABI.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the 2 byte padding in struct bpf_tunnel_key between tunnel_ttl
and tunnel_label members explicit. No issue has been observed, and
gcc/llvm does padding for the old struct already, where tunnel_label
was not yet present, so the current code works, but since it's part
of uapi, make sure we don't introduce holes in structs.
Therefore, add tunnel_ext that we can use generically in future
(f.e. to flag OAM messages for backends, etc). Also add the offset
to the compat tests to be sure should some compilers not padd the
tail of the old version of bpf_tunnel_key.
Fixes: 4018ab1875 ("bpf: support flow label for bpf_skb_{set, get}_tunnel_key")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends bpf_tunnel_key with a tunnel_label member, that maps
to ip_tunnel_key's label so underlying backends like vxlan and geneve
can propagate the label to udp_tunnel6_xmit_skb(), where it's being set
in the IPv6 header. It allows for having 20 more bits to encode/decode
flow related meta information programmatically. Tested with vxlan and
geneve.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If kprobe is placed on spin_unlock then calling kmalloc/kfree from
bpf programs is not safe, since the following dead lock is possible:
kfree->spin_lock(kmem_cache_node->lock)...spin_unlock->kprobe->
bpf_prog->map_update->kmalloc->spin_lock(of the same kmem_cache_node->lock)
and deadlocks.
The following solutions were considered and some implemented, but
eventually discarded
- kmem_cache_create for every map
- add recursion check to slow-path of slub
- use reserved memory in bpf_map_update for in_irq or in preempt_disabled
- kmalloc via irq_work
At the end pre-allocation of all map elements turned out to be the simplest
solution and since the user is charged upfront for all the memory, such
pre-allocation doesn't affect the user space visible behavior.
Since it's impossible to tell whether kprobe is triggered in a safe
location from kmalloc point of view, use pre-allocation by default
and introduce new BPF_F_NO_PREALLOC flag.
While testing of per-cpu hash maps it was discovered
that alloc_percpu(GFP_ATOMIC) has odd corner cases and often
fails to allocate memory even when 90% of it is free.
The pre-allocation of per-cpu hash elements solves this problem as well.
Turned out that bpf_map_update() quickly followed by
bpf_map_lookup()+bpf_map_delete() is very common pattern used
in many of iovisor/bcc/tools, so there is additional benefit of
pre-allocation, since such use cases are must faster.
Since all hash map elements are now pre-allocated we can remove
atomic increment of htab->count and save few more cycles.
Also add bpf_map_precharge_memlock() to check rlimit_memlock early to avoid
large malloc/free done by users who don't have sufficient limits.
Pre-allocation is done with vmalloc and alloc/free is done
via percpu_freelist. Here are performance numbers for different
pre-allocation algorithms that were implemented, but discarded
in favor of percpu_freelist:
1 cpu:
pcpu_ida 2.1M
pcpu_ida nolock 2.3M
bt 2.4M
kmalloc 1.8M
hlist+spinlock 2.3M
pcpu_freelist 2.6M
4 cpu:
pcpu_ida 1.5M
pcpu_ida nolock 1.8M
bt w/smp_align 1.7M
bt no/smp_align 1.1M
kmalloc 0.7M
hlist+spinlock 0.2M
pcpu_freelist 2.0M
8 cpu:
pcpu_ida 0.7M
bt w/smp_align 0.8M
kmalloc 0.4M
pcpu_freelist 1.5M
32 cpu:
kmalloc 0.13M
pcpu_freelist 0.49M
pcpu_ida nolock is a modified percpu_ida algorithm without
percpu_ida_cpu locks and without cross-cpu tag stealing.
It's faster than existing percpu_ida, but not as fast as pcpu_freelist.
bt is a variant of block/blk-mq-tag.c simlified and customized
for bpf use case. bt w/smp_align is using cache line for every 'long'
(similar to blk-mq-tag). bt no/smp_align allocates 'long'
bitmasks continuously to save memory. It's comparable to percpu_ida
and in some cases faster, but slower than percpu_freelist
hlist+spinlock is the simplest free list with single spinlock.
As expeceted it has very bad scaling in SMP.
kmalloc is existing implementation which is still available via
BPF_F_NO_PREALLOC flag. It's significantly slower in single cpu and
in 8 cpu setup it's 3 times slower than pre-allocation with pcpu_freelist,
but saves memory, so in cases where map->max_entries can be large
and number of map update/delete per second is low, it may make
sense to use it.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After eBPF being able to programmatically access/manage tunnel key meta
data via commit d3aa45ce6b ("bpf: add helpers to access tunnel metadata")
and more recently also for IPv6 through c6c3345407 ("bpf: support ipv6
for bpf_skb_{set,get}_tunnel_key"), this work adds two complementary
helpers to generically access their auxiliary tunnel options.
Geneve and vxlan support this facility. For geneve, TLVs can be pushed,
and for the vxlan case its GBP extension. I.e. setting tunnel key for geneve
case only makes sense, if we can also read/write TLVs into it. In the GBP
case, it provides the flexibility to easily map the group policy ID in
combination with other helpers or maps.
I chose to model this as two separate helpers, bpf_skb_{set,get}_tunnel_opt(),
for a couple of reasons. bpf_skb_{set,get}_tunnel_key() is already rather
complex by itself, and there may be cases for tunnel key backends where
tunnel options are not always needed. If we would have integrated this
into bpf_skb_{set,get}_tunnel_key() nevertheless, we are very limited with
remaining helper arguments, so keeping compatibility on structs in case of
passing in a flat buffer gets more cumbersome. Separating both also allows
for more flexibility and future extensibility, f.e. options could be fed
directly from a map, etc.
Moreover, change geneve's xmit path to test only for info->options_len
instead of TUNNEL_GENEVE_OPT flag. This makes it more consistent with vxlan's
xmit path and allows for avoiding to specify a protocol flag in the API on
xmit, so it can be protocol agnostic. Having info->options_len is enough
information that is needed. Tested with vxlan and geneve.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added by 9a628224a6 ("ip_tunnel: Add dont fragment flag."), allow to
feed df flag into tunneling facilities (currently supported on TX by
vxlan, geneve and gre) as a hint from eBPF's bpf_skb_set_tunnel_key()
helper.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When overwriting parts of the packet with bpf_skb_store_bytes() that
were fed previously into skb->hash calculation, we should clear the
current hash with skb_clear_hash(), so that a next skb_get_hash() call
can determine the correct hash related to this skb.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The fix in 35e2d1152b ("tunnels: Allow IPv6 UDP checksums to be correctly
controlled.") changed behavior for bpf_set_tunnel_key() when in use with
IPv6 and thus uncovered a bug that TUNNEL_CSUM needed to be set but wasn't.
As a result, the stack dropped ingress vxlan IPv6 packets, that have been
sent via eBPF through collect meta data mode due to checksum now being zero.
Since after LCO, we enable IPv4 checksum by default, so make that analogous
and only provide a flag BPF_F_ZERO_CSUM_TX for the user to turn it off in
IPv4 case.
Fixes: 35e2d1152b ("tunnels: Allow IPv6 UDP checksums to be correctly controlled.")
Fixes: c6c3345407 ("bpf: support ipv6 for bpf_skb_{set,get}_tunnel_key")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using this helper for updating UDP checksums, we need to extend
this in order to write CSUM_MANGLED_0 for csum computations that result
into 0 as sum. Reason we need this is because packets with a checksum
could otherwise become incorrectly marked as a packet without a checksum.
Likewise, if the user indicates BPF_F_MARK_MANGLED_0, then we should
not turn packets without a checksum into ones with a checksum.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For L4 checksums, we currently have bpf_l4_csum_replace() helper. It's
currently limited to handle 2 and 4 byte changes in a header and feeds the
from/to into inet_proto_csum_replace{2,4}() helpers of the kernel. When
working with IPv6, for example, this makes it rather cumbersome to deal
with, similarly when editing larger parts of a header.
Instead, extend the API in a more generic way: For bpf_l4_csum_replace(),
add a case for header field mask of 0 to change the checksum at a given
offset through inet_proto_csum_replace_by_diff(), and provide a helper
bpf_csum_diff() that can generically calculate a from/to diff for arbitrary
amounts of data.
This can be used in multiple ways: for the bpf_l4_csum_replace() only
part, this even provides us with the option to insert precalculated diffs
from user space f.e. from a map, or from bpf_csum_diff() during runtime.
bpf_csum_diff() has a optional from/to stack buffer input, so we can
calculate a diff by using a scratchbuffer for scenarios where we're
inserting (from is NULL), removing (to is NULL) or diffing (from/to buffers
don't need to be of equal size) data. Also, bpf_csum_diff() allows to
feed a previous csum into csum_partial(), so the function can also be
cascaded.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
add new map type to store stack traces and corresponding helper
bpf_get_stackid(ctx, map, flags) - walk user or kernel stack and return id
@ctx: struct pt_regs*
@map: pointer to stack_trace map
@flags: bits 0-7 - numer of stack frames to skip
bit 8 - collect user stack instead of kernel
bit 9 - compare stacks by hash only
bit 10 - if two different stacks hash into the same stackid
discard old
other bits - reserved
Return: >= 0 stackid on success or negative error
stackid is a 32-bit integer handle that can be further combined with
other data (including other stackid) and used as a key into maps.
Userspace will access stackmap using standard lookup/delete syscall commands to
retrieve full stack trace for given stackid.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Primary use case is a histogram array of latency
where bpf program computes the latency of block requests or other
events and stores histogram of latency into array of 64 elements.
All cpus are constantly running, so normal increment is not accurate,
bpf_xadd causes cache ping-pong and this per-cpu approach allows
fastest collision-free counters.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce BPF_MAP_TYPE_PERCPU_HASH map type which is used to do
accurate counters without need to use BPF_XADD instruction which turned
out to be too costly for high-performance network monitoring.
In the typical use case the 'key' is the flow tuple or other long
living object that sees a lot of events per second.
bpf_map_lookup_elem() returns per-cpu area.
Example:
struct {
u32 packets;
u32 bytes;
} * ptr = bpf_map_lookup_elem(&map, &key);
/* ptr points to this_cpu area of the value, so the following
* increments will not collide with other cpus
*/
ptr->packets ++;
ptr->bytes += skb->len;
bpf_update_elem() atomically creates a new element where all per-cpu
values are zero initialized and this_cpu value is populated with
given 'value'.
Note that non-per-cpu hash map always allocates new element
and then deletes old after rcu grace period to maintain atomicity
of update. Per-cpu hash map updates element values in-place.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After IPv6 support has recently been added to metadata dst and related
encaps, add support for populating/reading it from an eBPF program.
Commit d3aa45ce6b ("bpf: add helpers to access tunnel metadata") started
with initial IPv4-only support back then (due to IPv6 metadata support
not being available yet).
To stay compatible with older programs, we need to test for the passed
structure size. Also TOS and TTL support from the ip_tunnel_info key has
been added. Tested with vxlan devs in collect meta data mode with IPv4,
IPv6 and in compat mode over different network namespaces.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export flags used by eBPF helper functions through UAPI, so they can be
used by programs (instead of them redefining all flags each time or just
using the hard-coded values). It also gives a better overview what flags
are used where and we can further get rid of the extra macros defined in
filter.c. Moreover, reject invalid flags.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hacking tc programs with eBPF, one of the issues that come up
from time to time is to load addresses from headers. In eBPF as in
classic BPF, we have BPF_LD | BPF_ABS | BPF_{B,H,W} instructions that
extract a byte, half-word or word out of the skb data though helpers
such as bpf_load_pointer() (interpreter case).
F.e. extracting a whole IPv6 address could possibly look like ...
union v6addr {
struct {
__u32 p1;
__u32 p2;
__u32 p3;
__u32 p4;
};
__u8 addr[16];
};
[...]
a.p1 = htonl(load_word(skb, off));
a.p2 = htonl(load_word(skb, off + 4));
a.p3 = htonl(load_word(skb, off + 8));
a.p4 = htonl(load_word(skb, off + 12));
[...]
/* access to a.addr[...] */
This work adds a complementary helper bpf_skb_load_bytes() (we also
have bpf_skb_store_bytes()) as an alternative where the same call
would look like from an eBPF program:
ret = bpf_skb_load_bytes(skb, off, addr, sizeof(addr));
Same verifier restrictions apply as in ffeedafbf0 ("bpf: introduce
current->pid, tgid, uid, gid, comm accessors") case, where stack memory
access needs to be statically verified and thus guaranteed to be
initialized in first use (otherwise verifier cannot tell whether a
subsequent access to it is valid or not as it's runtime dependent).
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds support for "persistent" eBPF maps/programs. The term
"persistent" is to be understood that maps/programs have a facility
that lets them survive process termination. This is desired by various
eBPF subsystem users.
Just to name one example: tc classifier/action. Whenever tc parses
the ELF object, extracts and loads maps/progs into the kernel, these
file descriptors will be out of reach after the tc instance exits.
So a subsequent tc invocation won't be able to access/relocate on this
resource, and therefore maps cannot easily be shared, f.e. between the
ingress and egress networking data path.
The current workaround is that Unix domain sockets (UDS) need to be
instrumented in order to pass the created eBPF map/program file
descriptors to a third party management daemon through UDS' socket
passing facility. This makes it a bit complicated to deploy shared
eBPF maps or programs (programs f.e. for tail calls) among various
processes.
We've been brainstorming on how we could tackle this issue and various
approches have been tried out so far, which can be read up further in
the below reference.
The architecture we eventually ended up with is a minimal file system
that can hold map/prog objects. The file system is a per mount namespace
singleton, and the default mount point is /sys/fs/bpf/. Any subsequent
mounts within a given namespace will point to the same instance. The
file system allows for creating a user-defined directory structure.
The objects for maps/progs are created/fetched through bpf(2) with
two new commands (BPF_OBJ_PIN/BPF_OBJ_GET). I.e. a bpf file descriptor
along with a pathname is being passed to bpf(2) that in turn creates
(we call it eBPF object pinning) the file system nodes. Only the pathname
is being passed to bpf(2) for getting a new BPF file descriptor to an
existing node. The user can use that to access maps and progs later on,
through bpf(2). Removal of file system nodes is being managed through
normal VFS functions such as unlink(2), etc. The file system code is
kept to a very minimum and can be further extended later on.
The next step I'm working on is to add dump eBPF map/prog commands
to bpf(2), so that a specification from a given file descriptor can
be retrieved. This can be used by things like CRIU but also applications
can inspect the meta data after calling BPF_OBJ_GET.
Big thanks also to Alexei and Hannes who significantly contributed
in the design discussion that eventually let us end up with this
architecture here.
Reference: https://lkml.org/lkml/2015/10/15/925
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This helper is used to send raw data from eBPF program into
special PERF_TYPE_SOFTWARE/PERF_COUNT_SW_BPF_OUTPUT perf_event.
User space needs to perf_event_open() it (either for one or all cpus) and
store FD into perf_event_array (similar to bpf_perf_event_read() helper)
before eBPF program can send data into it.
Today the programs triggered by kprobe collect the data and either store
it into the maps or print it via bpf_trace_printk() where latter is the debug
facility and not suitable to stream the data. This new helper replaces
such bpf_trace_printk() usage and allows programs to have dedicated
channel into user space for post-processing of the raw data collected.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using routing realms as part of the classifier is quite useful, it
can be viewed as a tag for one or multiple routing entries (think of
an analogy to net_cls cgroup for processes), set by user space routing
daemons or via iproute2 as an indicator for traffic classifiers and
later on processed in the eBPF program.
Unlike actions, the classifier can inspect device flags and enable
netif_keep_dst() if necessary. tc actions don't have that possibility,
but in case people know what they are doing, it can be used from there
as well (e.g. via devs that must keep dsts by design anyway).
If a realm is set, the handler returns the non-zero realm. User space
can set the full 32bit realm for the dst.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Existing bpf_clone_redirect() helper clones skb before redirecting
it to RX or TX of destination netdev.
Introduce bpf_redirect() helper that does that without cloning.
Benchmarked with two hosts using 10G ixgbe NICs.
One host is doing line rate pktgen.
Another host is configured as:
$ tc qdisc add dev $dev ingress
$ tc filter add dev $dev root pref 10 u32 match u32 0 0 flowid 1:2 \
action bpf run object-file tcbpf1_kern.o section clone_redirect_xmit drop
so it receives the packet on $dev and immediately xmits it on $dev + 1
The section 'clone_redirect_xmit' in tcbpf1_kern.o file has the program
that does bpf_clone_redirect() and performance is 2.0 Mpps
$ tc filter add dev $dev root pref 10 u32 match u32 0 0 flowid 1:2 \
action bpf run object-file tcbpf1_kern.o section redirect_xmit drop
which is using bpf_redirect() - 2.4 Mpps
and using cls_bpf with integrated actions as:
$ tc filter add dev $dev root pref 10 \
bpf run object-file tcbpf1_kern.o section redirect_xmit integ_act classid 1
performance is 2.5 Mpps
To summarize:
u32+act_bpf using clone_redirect - 2.0 Mpps
u32+act_bpf using redirect - 2.4 Mpps
cls_bpf using redirect - 2.5 Mpps
For comparison linux bridge in this setup is doing 2.1 Mpps
and ixgbe rx + drop in ip_rcv - 7.8 Mpps
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Often cls_bpf classifier is used with single action drop attached.
Optimize this use case and let cls_bpf return both classid and action.
For backwards compatibility reasons enable this feature under
TCA_BPF_FLAG_ACT_DIRECT flag.
Then more interesting programs like the following are easier to write:
int cls_bpf_prog(struct __sk_buff *skb)
{
/* classify arp, ip, ipv6 into different traffic classes
* and drop all other packets
*/
switch (skb->protocol) {
case htons(ETH_P_ARP):
skb->tc_classid = 1;
break;
case htons(ETH_P_IP):
skb->tc_classid = 2;
break;
case htons(ETH_P_IPV6):
skb->tc_classid = 3;
break;
default:
return TC_ACT_SHOT;
}
return TC_ACT_OK;
}
Joint work with Daniel Borkmann.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the perf_event_map_fd and index, the function
bpf_perf_event_read() can convert the corresponding map
value to the pointer to struct perf_event and return the
Hardware PMU counter value.
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new bpf map type 'BPF_MAP_TYPE_PERF_EVENT_ARRAY'.
This map only stores the pointer to struct perf_event. The
user space event FDs from perf_event_open() syscall are converted
to the pointer to struct perf_event and stored in map.
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add skb->hash to the __sk_buff offset map, so it can be accessed from
an eBPF program. We currently already do this for classic BPF filters,
but not yet on eBPF, it might be useful as a demuxer in combination with
helpers like bpf_clone_redirect(), toy example:
__section("cls-lb") int ingress_main(struct __sk_buff *skb)
{
unsigned int which = 3 + (skb->hash & 7);
/* bpf_skb_store_bytes(skb, ...); */
/* bpf_l{3,4}_csum_replace(skb, ...); */
bpf_clone_redirect(skb, which, 0);
return -1;
}
I was thinking whether to add skb_get_hash(), but then concluded the
raw skb->hash seems fine in this case: we can directly access the hash
w/o extra eBPF helper function call, it's filled out by many NICs on
ingress, and in case the entropy level would not be sufficient, people
can still implement their own specific sw fallback hash mix anyway.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow eBPF programs attached to TC qdiscs call skb_vlan_push/pop via
helper functions. These functions may change skb->data/hlen which are
cached by some JITs to improve performance of ld_abs/ld_ind instructions.
Therefore JITs need to recognize bpf_skb_vlan_push/pop() calls,
re-compute header len and re-cache skb->data/hlen back into cpu registers.
Note, skb->data/hlen are not directly accessible from the programs,
so any changes to skb->data done either by these helpers or by other
TC actions are safe.
eBPF JIT supported by three architectures:
- arm64 JIT is using bpf_load_pointer() without caching, so it's ok as-is.
- x64 JIT re-caches skb->data/hlen unconditionally after vlan_push/pop calls
(experiments showed that conditional re-caching is slower).
- s390 JIT falls back to interpreter for now when bpf_skb_vlan_push() is present
in the program (re-caching is tbd).
These helpers allow more scalable handling of vlan from the programs.
Instead of creating thousands of vlan netdevs on top of eth0 and attaching
TC+ingress+bpf to all of them, the program can be attached to eth0 directly
and manipulate vlans as necessary.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It would be very useful to retrieve the net_cls's classid from an eBPF
program to allow for a more fine-grained classification, it could be
directly used or in conjunction with additional policies. I.e. docker,
but also tooling such as cgexec, can easily run applications via net_cls
cgroups:
cgcreate -g net_cls:/foo
echo 42 > foo/net_cls.classid
cgexec -g net_cls:foo <prog>
Thus, their respecitve classid cookie of foo can then be looked up on
the egress path to apply further policies. The helper is desigend such
that a non-zero value returns the cgroup id.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Thomas Graf <tgraf@suug.ch>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eBPF programs attached to kprobes need to filter based on
current->pid, uid and other fields, so introduce helper functions:
u64 bpf_get_current_pid_tgid(void)
Return: current->tgid << 32 | current->pid
u64 bpf_get_current_uid_gid(void)
Return: current_gid << 32 | current_uid
bpf_get_current_comm(char *buf, int size_of_buf)
stores current->comm into buf
They can be used from the programs attached to TC as well to classify packets
based on current task fields.
Update tracex2 example to print histogram of write syscalls for each process
instead of aggregated for all.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
allow programs read/write skb->mark, tc_index fields and
((struct qdisc_skb_cb *)cb)->data.
mark and tc_index are generically useful in TC.
cb[0]-cb[4] are primarily used to pass arguments from one
program to another called via bpf_tail_call() which can
be seen in sockex3_kern.c example.
All fields of 'struct __sk_buff' are readable to socket and tc_cls_act progs.
mark, tc_index are writeable from tc_cls_act only.
cb[0]-cb[4] are writeable by both sockets and tc_cls_act.
Add verifier tests and improve sample code.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow eBPF programs attached to classifier/actions to call
bpf_clone_redirect(skb, ifindex, flags) helper which will
mirror or redirect the packet by dynamic ifindex selection
from within the program to a target device either at ingress
or at egress. Can be used for various scenarios, for example,
to load balance skbs into veths, split parts of the traffic
to local taps, etc.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
classic BPF already exposes skb->dev->ifindex via SKF_AD_IFINDEX extension.
Allow eBPF program to access it as well. Note that classic aborts execution
of the program if 'skb->dev == NULL' (which is inconvenient for program
writers), whereas eBPF returns zero in such case.
Also expose the 'skb_iif' field, since programs triggered by redirected
packet need to known the original interface index.
Summary:
__skb->ifindex -> skb->dev->ifindex
__skb->ingress_ifindex -> skb->skb_iif
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
introduce bpf_tail_call(ctx, &jmp_table, index) helper function
which can be used from BPF programs like:
int bpf_prog(struct pt_regs *ctx)
{
...
bpf_tail_call(ctx, &jmp_table, index);
...
}
that is roughly equivalent to:
int bpf_prog(struct pt_regs *ctx)
{
...
if (jmp_table[index])
return (*jmp_table[index])(ctx);
...
}
The important detail that it's not a normal call, but a tail call.
The kernel stack is precious, so this helper reuses the current
stack frame and jumps into another BPF program without adding
extra call frame.
It's trivially done in interpreter and a bit trickier in JITs.
In case of x64 JIT the bigger part of generated assembler prologue
is common for all programs, so it is simply skipped while jumping.
Other JITs can do similar prologue-skipping optimization or
do stack unwind before jumping into the next program.
bpf_tail_call() arguments:
ctx - context pointer
jmp_table - one of BPF_MAP_TYPE_PROG_ARRAY maps used as the jump table
index - index in the jump table
Since all BPF programs are idenitified by file descriptor, user space
need to populate the jmp_table with FDs of other BPF programs.
If jmp_table[index] is empty the bpf_tail_call() doesn't jump anywhere
and program execution continues as normal.
New BPF_MAP_TYPE_PROG_ARRAY map type is introduced so that user space can
populate this jmp_table array with FDs of other bpf programs.
Programs can share the same jmp_table array or use multiple jmp_tables.
The chain of tail calls can form unpredictable dynamic loops therefore
tail_call_cnt is used to limit the number of calls and currently is set to 32.
Use cases:
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
==========
- simplify complex programs by splitting them into a sequence of small programs
- dispatch routine
For tracing and future seccomp the program may be triggered on all system
calls, but processing of syscall arguments will be different. It's more
efficient to implement them as:
int syscall_entry(struct seccomp_data *ctx)
{
bpf_tail_call(ctx, &syscall_jmp_table, ctx->nr /* syscall number */);
... default: process unknown syscall ...
}
int sys_write_event(struct seccomp_data *ctx) {...}
int sys_read_event(struct seccomp_data *ctx) {...}
syscall_jmp_table[__NR_write] = sys_write_event;
syscall_jmp_table[__NR_read] = sys_read_event;
For networking the program may call into different parsers depending on
packet format, like:
int packet_parser(struct __sk_buff *skb)
{
... parse L2, L3 here ...
__u8 ipproto = load_byte(skb, ... offsetof(struct iphdr, protocol));
bpf_tail_call(skb, &ipproto_jmp_table, ipproto);
... default: process unknown protocol ...
}
int parse_tcp(struct __sk_buff *skb) {...}
int parse_udp(struct __sk_buff *skb) {...}
ipproto_jmp_table[IPPROTO_TCP] = parse_tcp;
ipproto_jmp_table[IPPROTO_UDP] = parse_udp;
- for TC use case, bpf_tail_call() allows to implement reclassify-like logic
- bpf_map_update_elem/delete calls into BPF_MAP_TYPE_PROG_ARRAY jump table
are atomic, so user space can build chains of BPF programs on the fly
Implementation details:
=======================
- high performance of bpf_tail_call() is the goal.
It could have been implemented without JIT changes as a wrapper on top of
BPF_PROG_RUN() macro, but with two downsides:
. all programs would have to pay performance penalty for this feature and
tail call itself would be slower, since mandatory stack unwind, return,
stack allocate would be done for every tailcall.
. tailcall would be limited to programs running preempt_disabled, since
generic 'void *ctx' doesn't have room for 'tail_call_cnt' and it would
need to be either global per_cpu variable accessed by helper and by wrapper
or global variable protected by locks.
In this implementation x64 JIT bypasses stack unwind and jumps into the
callee program after prologue.
- bpf_prog_array_compatible() ensures that prog_type of callee and caller
are the same and JITed/non-JITed flag is the same, since calling JITed
program from non-JITed is invalid, since stack frames are different.
Similarly calling kprobe type program from socket type program is invalid.
- jump table is implemented as BPF_MAP_TYPE_PROG_ARRAY to reuse 'map'
abstraction, its user space API and all of verifier logic.
It's in the existing arraymap.c file, since several functions are
shared with regular array map.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the short-term solution, lets fix bpf helper functions to use
skb->mac_header relative offsets instead of skb->data in order to
get the same eBPF programs with cls_bpf and act_bpf work on ingress
and egress qdisc path. We need to ensure that mac_header is set
before calling into programs. This is effectively the first option
from below referenced discussion.
More long term solution for LD_ABS|LD_IND instructions will be more
intrusive but also more beneficial than this, and implemented later
as it's too risky at this point in time.
I.e., we plan to look into the option of moving skb_pull() out of
eth_type_trans() and into netif_receive_skb() as has been suggested
as second option. Meanwhile, this solution ensures ingress can be
used with eBPF, too, and that we won't run into ABI troubles later.
For dealing with negative offsets inside eBPF helper functions,
we've implemented bpf_skb_clone_unwritable() to test for unwriteable
headers.
Reference: http://thread.gmane.org/gmane.linux.network/359129/focus=359694
Fixes: 608cd71a9c ("tc: bpf: generalize pedit action")
Fixes: 91bc4822c3 ("tc: bpf: add checksum helpers")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add BQL support to via-rhine, from Tino Reichardt.
2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers
can support hw switch offloading. From Floria Fainelli.
3) Allow 'ip address' commands to initiate multicast group join/leave,
from Madhu Challa.
4) Many ipv4 FIB lookup optimizations from Alexander Duyck.
5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel
Borkmann.
6) Remove the ugly compat support in ARP for ugly layers like ax25,
rose, etc. And use this to clean up the neigh layer, then use it to
implement MPLS support. All from Eric Biederman.
7) Support L3 forwarding offloading in switches, from Scott Feldman.
8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed
up route lookups even further. From Alexander Duyck.
9) Many improvements and bug fixes to the rhashtable implementation,
from Herbert Xu and Thomas Graf. In particular, in the case where
an rhashtable user bulk adds a large number of items into an empty
table, we expand the table much more sanely.
10) Don't make the tcp_metrics hash table per-namespace, from Eric
Biederman.
11) Extend EBPF to access SKB fields, from Alexei Starovoitov.
12) Split out new connection request sockets so that they can be
established in the main hash table. Much less false sharing since
hash lookups go direct to the request sockets instead of having to
go first to the listener then to the request socks hashed
underneath. From Eric Dumazet.
13) Add async I/O support for crytpo AF_ALG sockets, from Tadeusz Struk.
14) Support stable privacy address generation for RFC7217 in IPV6. From
Hannes Frederic Sowa.
15) Hash network namespace into IP frag IDs, also from Hannes Frederic
Sowa.
16) Convert PTP get/set methods to use 64-bit time, from Richard
Cochran.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1816 commits)
fm10k: Bump driver version to 0.15.2
fm10k: corrected VF multicast update
fm10k: mbx_update_max_size does not drop all oversized messages
fm10k: reset head instead of calling update_max_size
fm10k: renamed mbx_tx_dropped to mbx_tx_oversized
fm10k: update xcast mode before synchronizing multicast addresses
fm10k: start service timer on probe
fm10k: fix function header comment
fm10k: comment next_vf_mbx flow
fm10k: don't handle mailbox events in iov_event path and always process mailbox
fm10k: use separate workqueue for fm10k driver
fm10k: Set PF queues to unlimited bandwidth during virtualization
fm10k: expose tx_timeout_count as an ethtool stat
fm10k: only increment tx_timeout_count in Tx hang path
fm10k: remove extraneous "Reset interface" message
fm10k: separate PF only stats so that VF does not display them
fm10k: use hw->mac.max_queues for stats
fm10k: only show actual queues, not the maximum in hardware
fm10k: allow creation of VLAN on default vid
fm10k: fix unused warnings
...
Commit 608cd71a9c ("tc: bpf: generalize pedit action") has added the
possibility to mangle packet data to BPF programs in the tc pipeline.
This patch adds two helpers bpf_l3_csum_replace() and bpf_l4_csum_replace()
for fixing up the protocol checksums after the packet mangling.
It also adds 'flags' argument to bpf_skb_store_bytes() helper to avoid
unnecessary checksum recomputations when BPF programs adjusting l3/l4
checksums and documents all three helpers in uapi header.
Moreover, a sample program is added to show how BPF programs can make use
of the mangle and csum helpers.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the ability to read out the skb->priority from an eBPF
program, so that it can be taken into account from a tc filter
or action for the use-case where the priority is not being used
to directly override the filter classification in a qdisc, but
to tag traffic otherwise for the classifier; the priority can be
assigned from various places incl. user space, in future we may
also mangle it from an eBPF program.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Debugging of BPF programs needs some form of printk from the
program, so let programs call limited trace_printk() with %d %u
%x %p modifiers only.
Similar to kernel modules, during program load verifier checks
whether program is calling bpf_trace_printk() and if so, kernel
allocates trace_printk buffers and emits big 'this is debug
only' banner.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1427312966-8434-6-git-send-email-ast@plumgrid.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
bpf_ktime_get_ns() is used by programs to compute time delta
between events or as a timestamp
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1427312966-8434-5-git-send-email-ast@plumgrid.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
BPF programs, attached to kprobes, provide a safe way to execute
user-defined BPF byte-code programs without being able to crash or
hang the kernel in any way. The BPF engine makes sure that such
programs have a finite execution time and that they cannot break
out of their sandbox.
The user interface is to attach to a kprobe via the perf syscall:
struct perf_event_attr attr = {
.type = PERF_TYPE_TRACEPOINT,
.config = event_id,
...
};
event_fd = perf_event_open(&attr,...);
ioctl(event_fd, PERF_EVENT_IOC_SET_BPF, prog_fd);
'prog_fd' is a file descriptor associated with BPF program
previously loaded.
'event_id' is an ID of the kprobe created.
Closing 'event_fd':
close(event_fd);
... automatically detaches BPF program from it.
BPF programs can call in-kernel helper functions to:
- lookup/update/delete elements in maps
- probe_read - wraper of probe_kernel_read() used to access any
kernel data structures
BPF programs receive 'struct pt_regs *' as an input ('struct pt_regs' is
architecture dependent) and return 0 to ignore the event and 1 to store
kprobe event into the ring buffer.
Note, kprobes are a fundamentally _not_ a stable kernel ABI,
so BPF programs attached to kprobes must be recompiled for
every kernel version and user must supply correct LINUX_VERSION_CODE
in attr.kern_version during bpf_prog_load() call.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1427312966-8434-4-git-send-email-ast@plumgrid.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
existing TC action 'pedit' can munge any bits of the packet.
Generalize it for use in bpf programs attached as cls_bpf and act_bpf via
bpf_skb_store_bytes() helper function.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If vlan offloading takes place then vlan header is removed from frame
and its contents, both vlan_tci and vlan_proto, is available to user
space via TPACKET interface. However, only vlan_tci can be used in BPF
filters.
This commit introduces a new BPF extension. It makes possible to load
the value of vlan_proto (vlan TPID) to register A. Support for classic
BPF and eBPF is being added, analogous to skb->protocol.
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Michal Sekletar <msekleta@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to prepare eBPF support for tc action, we need to add
sched_act_type, so that the eBPF verifier is aware of what helper
function act_bpf may use, that it can load skb data and read out
currently available skb fields.
This is bascially analogous to 96be4325f4 ("ebpf: add sched_cls_type
and map it to sk_filter's verifier ops").
BPF_PROG_TYPE_SCHED_CLS and BPF_PROG_TYPE_SCHED_ACT need to be
separate since both will have a different set of functionality in
future (classifier vs action), thus we won't run into ABI troubles
when the point in time comes to diverge functionality from the
classifier.
The future plan for act_bpf would be that it will be able to write
into skb->data and alter selected fields mirrored in struct __sk_buff.
For an initial support, it's sufficient to map it to sk_filter_ops.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
as a follow on to patch 70006af955 ("bpf: allow eBPF access skb fields")
this patch allows 'protocol' and 'vlan_tci' fields to be accessible
from extended BPF programs.
The usage of 'protocol', 'vlan_present' and 'vlan_tci' fields is the same as
corresponding SKF_AD_PROTOCOL, SKF_AD_VLAN_TAG_PRESENT and SKF_AD_VLAN_TAG
accesses in classic BPF.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
introduce user accessible mirror of in-kernel 'struct sk_buff':
struct __sk_buff {
__u32 len;
__u32 pkt_type;
__u32 mark;
__u32 queue_mapping;
};
bpf programs can do:
int bpf_prog(struct __sk_buff *skb)
{
__u32 var = skb->pkt_type;
which will be compiled to bpf assembler as:
dst_reg = *(u32 *)(src_reg + 4) // 4 == offsetof(struct __sk_buff, pkt_type)
bpf verifier will check validity of access and will convert it to:
dst_reg = *(u8 *)(src_reg + offsetof(struct sk_buff, __pkt_type_offset))
dst_reg &= 7
since skb->pkt_type is a bitfield.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the possibility to obtain raw_smp_processor_id() in
eBPF. Currently, this is only possible in classic BPF where commit
da2033c282 ("filter: add SKF_AD_RXHASH and SKF_AD_CPU") has added
facilities for this.
Perhaps most importantly, this would also allow us to track per CPU
statistics with eBPF maps, or to implement a poor-man's per CPU data
structure through eBPF maps.
Example function proto-type looks like:
u32 (*smp_processor_id)(void) = (void *)BPF_FUNC_get_smp_processor_id;
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work is similar to commit 4cd3675ebf ("filter: added BPF
random opcode") and adds a possibility for packet sampling in eBPF.
Currently, this is only possible in classic BPF and useful to
combine sampling with f.e. packet sockets, possible also with tc.
Example function proto-type looks like:
u32 (*prandom_u32)(void) = (void *)BPF_FUNC_get_prandom_u32;
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As discussed recently and at netconf/netdev01, we want to prevent making
bpf_verifier_ops registration available for modules, but have them at a
controlled place inside the kernel instead.
The reason for this is, that out-of-tree modules can go crazy and define
and register any verfifier ops they want, doing all sorts of crap, even
bypassing available GPLed eBPF helper functions. We don't want to offer
such a shiny playground, of course, but keep strict control to ourselves
inside the core kernel.
This also encourages us to design eBPF user helpers carefully and
generically, so they can be shared among various subsystems using eBPF.
For the eBPF traffic classifier (cls_bpf), it's a good start to share
the same helper facilities as we currently do in eBPF for socket filters.
That way, we have BPF_PROG_TYPE_SCHED_CLS look like it's own type, thus
one day if there's a good reason to diverge the set of helper functions
from the set available to socket filters, we keep ABI compatibility.
In future, we could place all bpf_prog_type_list at a central place,
perhaps.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to export BPF_PSEUDO_MAP_FD to user space, as it's used in the
ELF BPF loader where instructions are being loaded that need map fixups.
An initial stage loads all maps into the kernel, and later on replaces
related instructions in the eBPF blob with BPF_PSEUDO_MAP_FD as source
register and the actual fd as immediate value.
The kernel verifier recognizes this keyword and replaces the map fd with
a real pointer internally.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
introduce program type BPF_PROG_TYPE_SOCKET_FILTER that is used
for attaching programs to sockets where ctx == skb.
add verifier checks for ABS/IND instructions which can only be seen
in socket filters, therefore the check:
if (env->prog->aux->prog_type != BPF_PROG_TYPE_SOCKET_FILTER)
verbose("BPF_LD_ABS|IND instructions are only allowed in socket filters\n");
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
expose bpf_map_lookup_elem(), bpf_map_update_elem(), bpf_map_delete_elem()
map accessors to eBPF programs
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add new map type BPF_MAP_TYPE_ARRAY and its implementation
- optimized for fastest possible lookup()
. in the future verifier/JIT may recognize lookup() with constant key
and optimize it into constant pointer. Can optimize non-constant
key into direct pointer arithmetic as well, since pointers and
value_size are constant for the life of the eBPF program.
In other words array_map_lookup_elem() may be 'inlined' by verifier/JIT
while preserving concurrent access to this map from user space
- two main use cases for array type:
. 'global' eBPF variables: array of 1 element with key=0 and value is a
collection of 'global' variables which programs can use to keep the state
between events
. aggregation of tracing events into fixed set of buckets
- all array elements pre-allocated and zero initialized at init time
- key as an index in array and can only be 4 byte
- map_delete_elem() returns EINVAL, since elements cannot be deleted
- map_update_elem() replaces elements in an non-atomic way
(for atomic updates hashtable type should be used instead)
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add new map type BPF_MAP_TYPE_HASH and its implementation
- maps are created/destroyed by userspace. Both userspace and eBPF programs
can lookup/update/delete elements from the map
- eBPF programs can be called in_irq(), so use spin_lock_irqsave() mechanism
for concurrent updates
- key/value are opaque range of bytes (aligned to 8 bytes)
- user space provides 3 configuration attributes via BPF syscall:
key_size, value_size, max_entries
- map takes care of allocating/freeing key/value pairs
- map_update_elem() must fail to insert new element when max_entries
limit is reached to make sure that eBPF programs cannot exhaust memory
- map_update_elem() replaces elements in an atomic way
- optimized for speed of lookup() which can be called multiple times from
eBPF program which itself is triggered by high volume of events
. in the future JIT compiler may recognize lookup() call and optimize it
further, since key_size is constant for life of eBPF program
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the current meaning of BPF_MAP_UPDATE_ELEM syscall command is:
either update existing map element or create a new one.
Initially the plan was to add a new command to handle the case of
'create new element if it didn't exist', but 'flags' style looks
cleaner and overall diff is much smaller (more code reused), so add 'flags'
attribute to BPF_MAP_UPDATE_ELEM command with the following meaning:
#define BPF_ANY 0 /* create new element or update existing */
#define BPF_NOEXIST 1 /* create new element if it didn't exist */
#define BPF_EXIST 2 /* update existing element */
bpf_update_elem(fd, key, value, BPF_NOEXIST) call can fail with EEXIST
if element already exists.
bpf_update_elem(fd, key, value, BPF_EXIST) can fail with ENOENT
if element doesn't exist.
Userspace will call it as:
int bpf_update_elem(int fd, void *key, void *value, __u64 flags)
{
union bpf_attr attr = {
.map_fd = fd,
.key = ptr_to_u64(key),
.value = ptr_to_u64(value),
.flags = flags;
};
return bpf(BPF_MAP_UPDATE_ELEM, &attr, sizeof(attr));
}
First two bits of 'flags' are used to encode style of bpf_update_elem() command.
Bits 2-63 are reserved for future use.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
userspace programs that use eBPF instruction macros need to include two files:
uapi/linux/filter.h and uapi/linux/bpf.h
Move common macro definitions that are shared between classic BPF and eBPF
into uapi/linux/bpf_common.h, so that user app can include only one bpf.h file
Cc: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add optional attributes for BPF_PROG_LOAD syscall:
union bpf_attr {
struct {
...
__u32 log_level; /* verbosity level of eBPF verifier */
__u32 log_size; /* size of user buffer */
__aligned_u64 log_buf; /* user supplied 'char *buffer' */
};
};
when log_level > 0 the verifier will return its verification log in the user
supplied buffer 'log_buf' which can be used by program author to analyze why
verifier rejected given program.
'Understanding eBPF verifier messages' section of Documentation/networking/filter.txt
provides several examples of these messages, like the program:
BPF_ST_MEM(BPF_DW, BPF_REG_10, -8, 0),
BPF_MOV64_REG(BPF_REG_2, BPF_REG_10),
BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, -8),
BPF_LD_MAP_FD(BPF_REG_1, 0),
BPF_CALL_FUNC(BPF_FUNC_map_lookup_elem),
BPF_JMP_IMM(BPF_JEQ, BPF_REG_0, 0, 1),
BPF_ST_MEM(BPF_DW, BPF_REG_0, 4, 0),
BPF_EXIT_INSN(),
will be rejected with the following multi-line message in log_buf:
0: (7a) *(u64 *)(r10 -8) = 0
1: (bf) r2 = r10
2: (07) r2 += -8
3: (b7) r1 = 0
4: (85) call 1
5: (15) if r0 == 0x0 goto pc+1
R0=map_ptr R10=fp
6: (7a) *(u64 *)(r0 +4) = 0
misaligned access off 4 size 8
The format of the output can change at any time as verifier evolves.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eBPF programs are similar to kernel modules. They are loaded by the user
process and automatically unloaded when process exits. Each eBPF program is
a safe run-to-completion set of instructions. eBPF verifier statically
determines that the program terminates and is safe to execute.
The following syscall wrapper can be used to load the program:
int bpf_prog_load(enum bpf_prog_type prog_type,
const struct bpf_insn *insns, int insn_cnt,
const char *license)
{
union bpf_attr attr = {
.prog_type = prog_type,
.insns = ptr_to_u64(insns),
.insn_cnt = insn_cnt,
.license = ptr_to_u64(license),
};
return bpf(BPF_PROG_LOAD, &attr, sizeof(attr));
}
where 'insns' is an array of eBPF instructions and 'license' is a string
that must be GPL compatible to call helper functions marked gpl_only
Upon succesful load the syscall returns prog_fd.
Use close(prog_fd) to unload the program.
User space tests and examples follow in the later patches
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'maps' is a generic storage of different types for sharing data between kernel
and userspace.
The maps are accessed from user space via BPF syscall, which has commands:
- create a map with given type and attributes
fd = bpf(BPF_MAP_CREATE, union bpf_attr *attr, u32 size)
returns fd or negative error
- lookup key in a given map referenced by fd
err = bpf(BPF_MAP_LOOKUP_ELEM, union bpf_attr *attr, u32 size)
using attr->map_fd, attr->key, attr->value
returns zero and stores found elem into value or negative error
- create or update key/value pair in a given map
err = bpf(BPF_MAP_UPDATE_ELEM, union bpf_attr *attr, u32 size)
using attr->map_fd, attr->key, attr->value
returns zero or negative error
- find and delete element by key in a given map
err = bpf(BPF_MAP_DELETE_ELEM, union bpf_attr *attr, u32 size)
using attr->map_fd, attr->key
- iterate map elements (based on input key return next_key)
err = bpf(BPF_MAP_GET_NEXT_KEY, union bpf_attr *attr, u32 size)
using attr->map_fd, attr->key, attr->next_key
- close(fd) deletes the map
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF syscall is a multiplexor for a range of different operations on eBPF.
This patch introduces syscall with single command to create a map.
Next patch adds commands to access maps.
'maps' is a generic storage of different types for sharing data between kernel
and userspace.
Userspace example:
/* this syscall wrapper creates a map with given type and attributes
* and returns map_fd on success.
* use close(map_fd) to delete the map
*/
int bpf_create_map(enum bpf_map_type map_type, int key_size,
int value_size, int max_entries)
{
union bpf_attr attr = {
.map_type = map_type,
.key_size = key_size,
.value_size = value_size,
.max_entries = max_entries
};
return bpf(BPF_MAP_CREATE, &attr, sizeof(attr));
}
'union bpf_attr' is backwards compatible with future extensions.
More details in Documentation/networking/filter.txt and in manpage
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
allow user space to generate eBPF programs
uapi/linux/bpf.h: eBPF instruction set definition
linux/filter.h: the rest
This patch only moves macro definitions, but practically it freezes existing
eBPF instruction set, though new instructions can still be added in the future.
These eBPF definitions cannot go into uapi/linux/filter.h, since the names
may conflict with existing applications.
Full eBPF ISA description is in Documentation/networking/filter.txt
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann