Currently it can send regulatory domain change notification before any
NEW_WIPHY notification. Moreover, if rfill_register() fails, calling
wiphy_unregister() will send a DEL_WIPHY though no NEW_WIPHY had been
sent previously.
Thus reordering so it properly notifies NEW_WIPHY before any other.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since "wireless-regdb: remove antenna gain" was merged in the
wireless-regdb tree, the awk script parser has been incompatible
with the 'official' regulatory database. This fixes that up.
Without this change the max EIRP is set to 0 making 802.11 devices
useless.
The fragile nature of the awk parser must be replaced, but ideas
over how to do that in the most scalable way are being reviewed.
In the meantime update the documentation for CFG80211_INTERNAL_REGDB
so folks are aware of expectations for now.
Reported-by: John Walker <john@x109.net>
Reported-by: Krishna Chaitanya <chaitanya.mgit@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some VHT TDLS peers (Google Nexus 5) include the VHT-AID IE in their
TDLS setup request/response. Usermode passes this aid as the station
aid, causing it to fail verifiction, since this happens in the
"set_station" stage. Make an exception for the TDLS use-case.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
tsc can be NULL (mac80211 currently always passes NULL),
resulting in NULL-dereference. check before copying it.
Cc: stable@vger.kernel.org
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Driver is now responsible for veryfing if the
switch is possible.
Since this is inherently tricky driver may decide
to disconnect an interface later with
cfg80211_stop_iface().
This doesn't mean driver can accept everything. It
should do it's best to verify requests and reject
them as soon as possible.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The non-split wiphy state shouldn't be increased in size
so move the new set_qos_map command into the split if
statement.
Cc: stable@vger.kernel.org (3.14+)
Fixes: fa9ffc7456 ("cfg80211: Add support for QoS mapping")
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TDLS initiator is set once during link setup. If determines the
address ordering in the link identifier IE.
Fix dependent drivers - mwifiex and mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
MAX_JIFFY_OFFSET has no meaning when calculating the
elapsed jiffies, as jiffies run out until ULONG_MAX.
This miscalculation results in erroneous values
in case of a wrap-around.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 8eca1fb692.
Felix notes that this broke regulatory, leaving channel 12 open for AP
operation in the US regulatory domain where it isn't permitted.
Link: http://mid.gmane.org/53A6C0FF.9090104@openwrt.org
Reported-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, cfg80211 tries to implement ethtool, but that doesn't
really scale well, with all the different operations. Make the
lower-level driver responsible for it, which currently only has
an effect on mac80211. It will similarly not scale well at that
level though, since mac80211 also has many drivers.
To cleanly implement this in mac80211, introduce a new file and
move some code to appropriate places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Generalize the power conversion from mW to dBm
using log. This should fix the below compilation
error for country NO which adds a new power value
2000mW which is not handled earlier.
CC [M] net/wireless/wext-sme.o
CC [M] net/wireless/regdb.o
net/wireless/regdb.c:1130:1: error: Unknown undeclared here (not in
a function)
net/wireless/regdb.c:1130:9: error: expected } before power
make[2]: *** [net/wireless/regdb.o] Error 1
make[1]: *** [net/wireless] Error 2
make: *** [net] Error 2
Reported-By: John Walker <john@x109.net>
Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
[remove unneeded parentheses, fix rounding by using %.0f]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We're currently sending NEW_WIPHY events for renames (which
is a bit odd, but now can't be changed), but also send them
for really new devices that register.
Also send DEL_WIPHY events when a device is removed, the
event ID for this was already reserved.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channels in 2.4GHz band overlap, this means that if we
send a probe request on channel 1 and then move to channel
2, we will hear the probe response on channel 2. In this
case, the RSSI will be lower than if we had heard it on
the channel on which it was sent (1 in this case).
The firmware / low level driver can parse the channel in
the DS IE or HT IE and compensate the RSSI so that it will
still have a valid value even if we heard the frame on an
adjacent channel. This can be done up to a certain offset.
Add this offset as a configuration for the low level driver.
A low level driver that can compensate the low RSSI in this
case should assign the maximal offset for which the RSSI
value is still valid.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise every "indoor" setting by usermode will cause a regdomain reset.
Acked-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement and export the new cfg80211_get_station() API.
This utility can be used by other kernel modules to obtain
detailed information about a given wireless station.
It will be in particular useful to batman-adv which will
implement a wireless rate based metric.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Users may need information about the expected throughput
towards a given peer.
This value is supposed to consider the size overhead
generated by the 802.11 header.
This value is exported in kbps through the get_station() API
by including it into the station_info object.
Moreover, it is sent to user space when replying to the
nl80211 GET_STATION command.
This information will be useful to the batman-adv module
which will use it for its new metric computation.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This requires changing the nl80211 parsing code a bit to use
intermediate pointers for the allocation, but clarifies the
API towards the drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This also propagates through the drivers.
The orinoco driver uses the cfg80211 API structs for internal
bookkeeping, and so needs a (void *) cast that removes the
const - but that's OK because it allocates those pointers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change the type of NL80211_ATTR_CSA_C_OFF_BEACON and
NL80211_ATTR_CSA_C_OFF_PRESP to be NLA_BINARY which allows
userspace to use beacons and probe responses with
multiple CSA counters.
This isn't breaking the API since userspace can
continue to use nla_put_u16 for this attributes, which
is equivalent to a single element u16 array.
In addition advertise max number of supported CSA counters.
This is needed when using CSA and eCSA IEs together.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add NL80211_ATTR_CSA_C_OFFSETS_TX which holds an array
of offsets to the CSA counters which should be updated
when sending a management frames with NL80211_CMD_FRAME.
This API should be used by the drivers that wish to keep the
CSA counter updated in probe responses, but do not implement
probe response offloading and so, do not use
ieee80211_proberesp_get function.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no need to pass NL80211_IFTYPE_UNSPECIFIED when calling
cfg80211_chandef_dfs_required() since we always already have the
interface type. So, pass the actual interface type instead.
Additionally, have cfg80211_chandef_dfs_required() WARN if the passed
interface type is NL80211_IFTYPE_UNSPECIFIED, so we can detect
problems more easily.
Tested-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At the moment, the ath9k/ath10k DFS module only supports detecting ETSI
radar patterns.
Add a bitmap in the interface combinations, indicating which DFS regions
are supported by the detector. If unset, support for all regions is
assumed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver fails during HW restart or resume, the whole
stack goes into a very confused state with interfaces being
up while the hardware is down etc.
Address this by shutting down everything; we'll run into a
lot of warnings in the process but that's better than having
the whole stack get messed up.
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This exports a new cfg80211_stop_iface() function.
This is intended for driver internal interface
combination management and channel switching.
Due to locking issues (it re-enters driver) the
call is asynchronous and uses cfg80211 event
list/worker.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add locked-version for cfg80211_sched_scan_stopped.
This is used for some users that might want to
call it when rtnl is already locked.
Fixes: d43c6b6 ("mac80211: reschedule sched scan after HW restart")
Cc: stable@vger.kernel.org (3.14+)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211 is notified about connection failures by
__cfg80211_connect_result() call. However, this
function currently does not free cfg80211 sme.
This results in hanging connection attempts in some cases
e.g. when mac80211 authentication attempt is denied,
we have this function call:
ieee80211_rx_mgmt_auth() -> cfg80211_rx_mlme_mgmt() ->
cfg80211_process_auth() -> cfg80211_sme_rx_auth() ->
__cfg80211_connect_result()
but cfg80211_sme_free() is never get called.
Fixes: ceca7b712 ("cfg80211: separate internal SME implementation")
Cc: stable@vger.kernel.org (3.10+)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These really can't trigger unless somebody messes up the code,
but don't make debugging it needlessly complicated, WARN and
return instead of BUG_ON().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This extends NL80211_CMD_SET_CHANNEL to allow dynamic channel bandwidth
changes in AP mode (including P2P GO) during a lifetime of the BSS. This
can be used to implement, e.g., HT 20/40 MHz co-existence rules on the
2.4 GHz band.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current code checks if the 20MHz bandwidth is allowed for
particular channel -- if it is not, the channel is disabled.
Since we need to use 5/10 MHz channels, this code is modified in
the way that the default bandwidth to check is 5MHz. If the
maximum bandwidth allowed by the channel is smaller than 5MHz,
the channel is disabled. Otherwise the channel is used and the
flags are set according to the bandwidth allowed by the channel.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since there are frequency bands (e.g. 5.9GHz) allowing channels
with only 10 or 5 MHz bandwidth, this patch adds attributes that
allow keeping track about this information.
When channel attributes are reported to user-space, make sure to
not break old tools, i.e. if the 'split wiphy dump' is enabled,
report the extra attributes (if present) describing the bandwidth
restrictions. If the 'split wiphy dump' is not enabled,
completely omit those channels that have flags set to either
IEEE80211_CHAN_NO_10MHZ or IEEE80211_CHAN_NO_20MHZ.
Add the check for new bandwidth restriction flags in
cfg80211_chandef_usable() to comply with the restrictions.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Return NOTIFY_DONE if we don't care this time's notification, return
NOTIFY_OK if we successfully handled this time's notification. That's
the formal way to do it.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Name wiphy_to_rdev is more accurate to describe what the function
does, i.e., return a pointer pointing to struct
cfg80211_registered_device.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Name "dev" is too common and ambiguous, let all the pointer name
pointing to struct cfg80211_registered_device be "rdev". This can
improve code readability and consistency(since other places have
already called it rdev).
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The patch splits cfg80211_check_combinations()
into an iterator function and a simple iteration
user.
This makes it possible for drivers to asses how
many channels can use given iftype setup. This in
turn can be used for future
multi-interface/multi-channel channel switching.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At some locations, channels 149-165 are considered a single
bundle, while at some other locations, e.g., Indonesia, channels
149-161 are considered a single bundle, while channel 165 belongs
to a different bundle. This means that:
1. A station interface connection to an AP on channel 165 allows
the instantiation of a P2P GO on channels 149-165.
2. A station interface connection to an AP on channels 149-161
does NOT allow the instantiation of a P2P GO on channel 165.
Fix this.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows processing of the last regulatory request when
we determine its still pending. Without this if a regulatory
request failed to get processed by userspace we wouldn't
be able to re-process it later. An example situation that can
lead to an unprocessed last_request is enabling cfg80211 to
be built-in to the kernel, not enabling CFG80211_INTERNAL_REGDB
and the CRDA binary not being available at the time the udev
rule that kicks of CRDA triggers.
In such a situation we want to let some cfg80211 triggers
eventually kick CRDA for us again. Without this if the first
cycle attempt to kick off CRDA failed we'd be stuck without
the ability to change process any further regulatory domains.
cfg80211 will trigger re-processing of the regulatory queue
whenever schedule_work(®_work) is called, currently this
happens when:
* suspend / resume
* disconnect
* a beacon hint gets triggered (non DFS 5 GHz AP found)
* a regulatory request gets added to the queue
We don't have any specific opportunistic late boot triggers
to address a late mount of where CRDA resides though, adding
that should be done separately through another patch.
Without an opportunistic fix then this fix relies at least
one of the triggeres above to happen.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avoid freeing the last request while it is being processed. This can
happen in some cases if reg_work is kicked for some reason while the
currently pending request is in flight.
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: Eliad Peller <eliad@wizery.com>
Tested-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set DFS CAC time also in case of using custom
and strict regulatory from drivers. In other case
we could have unset DFS CAC time directly after
driver loaded and before issue regulatory set from
user mode.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When looking for a BSS matching given parameters, ignore invalid
BSSIDs. This avoids, for example, trying to join an IBSS that has
a multicast BSSID, which isn't supported by all drivers nor is it
a valid configuration of the IBSS so better create a new one with
a correctly chosen random BSSID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_wext_freq() is declared in wext-compat.h, but its
parameter struct wiphy's declaration is not included there.
As the parameter isn't used, just remove it.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
[remove parameter instead of changing to netdev]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All bits from radar_detect must match combination
radar bitmask. Otherwise it is theoretically
possible to lead into an invalid combination
provided a driver reports strange combinations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Get rid of the cfg80211_can_add_interface() and
cfg80211_can_change_interface() functions by moving that functionality
to mac80211. With this patch all interface combination checks are now
out of cfg80211 (except for the channel switch case which will be
addressed in a future commit).
Additionally, modify the ieee80211_check_combinations() function so
that an undefined chandef can be passed, in order to use it before a
channel is defined.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that mac80211 can check the interface combinations itself, move
the combinations check from cfg80211 to mac80211 when joining an IBSS.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the counting part of the interface combination check from
cfg80211 to mac80211.
This is needed to simplify locking when the driver has to perform a
combination check by itself (eg. with channel-switch).
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some interface types don't require DFS (such as STATION, P2P_CLIENT
etc). In order to centralize these decisions, make
cfg80211_chandef_dfs_required() take the iftype into consideration.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Separate the code that counts the interface types and channels from
the code that check the interface combinations. The new function that
checks for combinations is exported so it can be called by the
drivers.
This is done in preparation for moving the interface combinations
checks out of cfg80211.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow GO operation on a channel marked with IEEE80211_CHAN_INDOOR_ONLY
iff there is a user hint indicating that the platform is operating in
an indoor environment, i.e., the platform is a printer or media center
device.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the option to hint the wireless core that it is operating in an indoor
environment.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow GO operation on a channel marked with IEEE80211_CHAN_GO_CONCURRENT
iff there is an active station interface that is associated to
an AP operating on the same channel in the 2 GHz band or the same UNII band
(in the 5 GHz band). This relaxation is not allowed if the channel is
marked with IEEE80211_CHAN_RADAR.
Note that this is a permissive approach to the FCC definitions,
that require a clear assessment that the device operating the AP is
an authorized master, i.e., with radar detection and DFS capabilities.
It is assumed that such restrictions are enforced by user space.
Furthermore, it is assumed, that if the conditions that allowed for
the operation of the GO on such a channel change, i.e., the station
interface disconnected from the AP, it is the responsibility of user
space to evacuate the GO from the channel.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the regulatory cellular base station hints support under
a specific configuration option and make the option depend
on CFG80211_CERTIFICATION_ONUS.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The FCC are clarifying some soft configuration requirements,
which among other include the following:
1. Indoor operation, where a device can use channels requiring indoor
operation, subject to that it can guarantee indoor operation,
i.e., the device is connected to AC Power or the device is under
the control of a local master that is acting as an AP and is
connected to AC Power.
2. Concurrent GO operation, where devices may instantiate a P2P GO
while they are under the guidance of an authorized master. For example,
on a channel on which a BSS is connected to an authorized master, i.e.,
with DFS and radar detection capability in the UNII band.
See https://apps.fcc.gov/eas/comments/GetPublishedDocument.html?id=327&tn=528122
Add support for advertising Indoor-only and GO-Concurrent channel
properties.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Wdev->ssid_len has already been set in cfg80211_connect() and is equal
to connect->ssid_len. Use wdev->ssid_len instead of connect->ssid_len
so it will be consistent with previous ssid assignment statement.
If bss is found in cfg80211_get_conn_bss(), wdev->conn->state is set
to CFG80211_CONN_AUTHENTICATE_NEXT in there. So it's not needed to set
it manually to CFG80211_CONN_AUTHENTICATE_NEXT if bss is found in that
function.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
rcu_assign_pointer() ensures that the initialization of a structure is
carried out before storing a pointer to that structure. However, in the
case that NULL is assigned there's no structure to initialize so using
RCU_INIT_POINTER instead is safe and more efficient.
Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com>
[rewrite commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When dynamically creating interfaces from userspace, e.g. for P2P usage,
such interfaces are usually owned by the process that created them, i.e.
wpa_supplicant. Should wpa_supplicant crash, such interfaces will often
cease operating properly and cause problems on restarting the process.
To avoid this problem, introduce an ownership concept for interfaces. If
an interface is owned by a netlink socket, then it will be destroyed if
the netlink socket is closed for any reason, including if the process it
belongs to crashed. This gives us a race-free way to get rid of any such
interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Macro ASSERT_RDEV_LOCK(rdev) is equal to ASSERT_RTNL(), so replace it
with ASSERT_RTNL() and remove it.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
RCU pointer bss->pub.beacon_ies is checked before in previous
statement:
if (rcu_access_pointer(bss->pub.beacon_ies))
continue;
There is no need to check it twice(and in the wrong way :) ).
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On 2.4Ghz band, the channels overlap since the delta
between different channels is 5Mhz while the width of the
receiver is 20Mhz (at least).
This means that we can hear beacons or probe responses from
adjacent channels. These frames will have a significant
lower RSSI which will feed all kinds of logic with inaccurate
data. An obvious example is the roaming algorithm that will
think our AP is getting weak and will try to move to another
AP.
In order to avoid this, update the signal only if the frame
has been heard on the same channel as the one advertised by
the AP in its DS / HT IEs.
We refrain from updating the values only if the AP is
already in the BSS list so that we will still have a valid
(but inaccurate) value if the AP was heard on an adjacent
channel only.
To achieve this, stop taking the channel from DS / HT IEs
in mac80211. The DS / HT IEs is taken into account to
discard the frame if it was received on a disabled channel.
This can happen due to the same phenomenon: the frame is
sent on channel 12, but heard on channel 11 while channel
12 can be disabled on certain devices. Since this check
is done in cfg80211, stop even checking this in mac80211.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[remove unused rx_freq variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Function __cfg80211_join_ibss() is only used in net/wireless/ibss.c,
so make it static.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
MPLS labels may contain traffic control information, which should be
evaluated and used by the wireless subsystem if present.
Also check for IEEE 802.21 which is always network control traffic.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain situations we want to trigger reprocessing
of the last regulatory hint. One situation in which
this makes sense is the case where the cfg80211 was
built-in to the kernel, CFG80211_INTERNAL_REGDB was not
enabled and the CRDA binary is on a partition not availble
during early boot. In such a case we want to be able to
re-process the same request at some other point.
When we are asked to re-process the same request we need
to be careful to not kfree it, addresses that.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[rename function]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of AP mode, the beacon interval is already reset to
zero inside cfg80211_stop_ap(), and in the other modes it
isn't relevant. Remove the assignment to remove a potential
race since the assignment isn't properly locked.
Reported-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit "nl80211: send event when AP operation is stopped" added an
event to notify user space that an AP interface has been stopped, to
handle cases such as suspend etc. The event is sent regardless
if the stop AP flow was triggered by user space or due to internal state
change.
This might cause issues with wpa_supplicant/hostapd flows that consider
stop AP flow as a synchronous one, e.g., AP/GO channel change in the
absence of CSA support. In such cases, the flow will restart the AP
immediately after the stop AP flow is done, and only handle the stop
AP event after the current flow is done, and as a result stop the AP
again.
Change the current implementation to only send the event in case the
stop AP was triggered due to an internal reason.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Send Channel Availability Check time as a parameter
of start_radar_detection() callback.
Get CAC time from regulatory database.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce DFS CAC time as a regd param, configured per REG_RULE and
set per channel in cfg80211. DFS CAC time is close connected with
regulatory database configuration. Instead of using hardcoded values,
get DFS CAC time form regulatory database. Pass DFS CAC time to user
mode (mainly for iw reg get, iw list, iw info). Allow setting DFS CAC
time via CRDA. Add support for internal regulatory database.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[rewrap commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow to set world regulatory domain in case of user
request (iw reg set 00).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reset regdomain to world regdomain in case
of errors in set_regdom() function.
This will fix a problem with such scenario:
- iw reg set US
- iw reg set 00
- iw reg set US
The last step always fail and we get deadlock
in kernel regulatory code. Next setting new
regulatory wasn't possible due to:
Pending regulatory request, waiting for it to be processed...
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need for the struct device_type with the uevent function
etc., just fill the country alpha2 when sending the event.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't have to double check whether the parameters passed to
cfg80211_can_use_iftype_chan() are correct. We should just make sure
they *are* when we call this function.
Remove the radar_detect argument check in
cfg80211_can_use_iftype_chan() to simplify the code.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
[keep braces around a long comment + single statement]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since mesh support for DFS channels was added, we also need to check
for DFS channels when performing a channel switch with
NL80211_IFTYPE_MESHPOINT.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
[use switch statement, slight code cleanup]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce NL80211_RRF_AUTO_BW rule flag. If this flag set
maximum available bandwidth should be calculated base on
contiguous rules and wider channels will be allowed to cross
multiple contiguous/overlapping frequency ranges.
In case of old kernels maximum bandwidth from regulatory
rule will be used, while there is no NL80211_RRF_AUTO_BW flag.
This fixes the previous commit 9752482083
("cfg80211: regulatory introduce maximum bandwidth calculation")
which was found to be a problem for userspace API compatibility.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[edit commit log, use sizeof()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While framing the TDLS Setup Confirmation frame, the driver needs to
know if the TDLS peer is VHT/HT/WMM capable and thus shall construct
the VHT/HT operation / WMM parameter elements accordingly. Supplicant
determines if the TDLS peer is VHT/HT/WMM capable based on the
presence of the respective IEs in the received TDLS Setup Response frame.
The host driver should not need to parse the received TDLS Response
frame and thus, should be able to rely on the supplicant to indicate
the capability of the peer through additional flags while transmitting
the TDLS Setup Confirmation frame through tdls_mgmt operations.
Signed-off-by: Sunil Dutt Undekari <usdutt@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After processing hint_user, we would want to schedule the
timeout work only if we are actually waiting to CRDA. This happens
when the status is not "IGNORE" nor "ALREADY_SET".
Signed-off-by: Inbal Hacohen <Inbal.Hacohen@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
One of my pet coding style peeves is the practice of
adding extra return; at the end of function.
Kill several instances of this in network code.
I suppose some coccinelle wizardy could do this automatically.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've already checked the IE length and assigned request->ie
based on that, so continue using it to make the code a bit
clearer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no driver using this flag and consequently no userspace
application is actually looking at it. As it seems unlikely for
any driver to start using it, remove it and the (very little)
code that used it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to the previous commit, when a scan finishes, it is in theory
possible to hit the following sequence:
1. interface starts being removed
2. scan is cancelled by driver and cfg80211 is notified
3. scan done work is scheduled
4. interface is removed completely, rdev->scan_req is freed,
event sent to userspace but scan done work remains pending
5. new scan is requested on another virtual interface
6. scan done work runs, freeing the still-running scan
To fix this situation, hang on to the scan done message and block
new scans while that is the case, and only send the message from
the work function, regardless of whether the scan_req is already
freed from interface removal. This makes step 5 above impossible
and changes step 6 to be
5. scan done work runs, sending the scan done message
As this can't work for wext, so we send the message immediately,
but this shouldn't be an issue since we still return -EBUSY.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an interface/wdev is removed, any ongoing scan should be
cancelled by the driver. This will make it call cfg80211, which
only queues a work struct. If interface/wdev removal is quick
enough, this can leave the scan request pending and processed
only after the interface is gone, causing a use-after-free.
Fix this by making sure the scan request is not pending after
the interface is destroyed. We can't flush or cancel the work
item due to locking concerns, but when it'll run it shouldn't
find anything to do. This leaves a potential issue, if a new
scan gets requested before the work runs, it prematurely stops
the running scan, potentially causing another crash. I'll fix
that in the next patch.
This was particularly observed with P2P_DEVICE wdevs, likely
because freeing them is quicker than freeing netdevs.
Reported-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Fixes: 4a58e7c384 ("cfg80211: don't "leak" uncompleted scans")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Unfortunately I forgot this during the merge window, but the
patch seems small enough to go in as a fix. The userspace API
bug that was the reason for disabling it has long been fixed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the netlink skb is exhausted split_start is left set. In the
subsequent retry, with a larger buffer, the dump is continued from the
failing point instead of from the beginning.
This was causing my rt28xx based USB dongle to now show up when
running "iw list" with an old iw version without split dump support.
Cc: stable@vger.kernel.org
Fixes: 3713b4e364 ("nl80211: allow splitting wiphy information in dumps")
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
[avoid the entire workaround when state->split is set]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case we will get regulatory request with rule
where max_bandwidth_khz is set to 0 handle this
case as a special one.
If max_bandwidth_khz == 0 we should calculate maximum
available bandwidth base on all frequency contiguous rules.
In case we need auto calculation we just have to set:
country PL: DFS-ETSI
(2402 - 2482 @ 40), (N/A, 20)
(5170 - 5250 @ AUTO), (N/A, 20)
(5250 - 5330 @ AUTO), (N/A, 20), DFS
(5490 - 5710 @ 80), (N/A, 27), DFS
This mean we will calculate maximum bw for rules where
AUTO (N/A) were set, 160MHz (5330 - 5170) in example above.
So we will get:
(5170 - 5250 @ 160), (N/A, 20)
(5250 - 5330 @ 160), (N/A, 20), DFS
In other case:
country FR: DFS-ETSI
(2402 - 2482 @ 40), (N/A, 20)
(5170 - 5250 @ AUTO), (N/A, 20)
(5250 - 5330 @ 80), (N/A, 20), DFS
(5490 - 5710 @ 80), (N/A, 27), DFS
We will get 80MHz (5250 - 5170):
(5170 - 5250 @ 80), (N/A, 20)
(5250 - 5330 @ 80), (N/A, 20), DFS
Base on this calculations we will set correct channel
bandwidth flags (eg. IEEE80211_CHAN_NO_80MHZ).
We don't need any changes in CRDA or internal regulatory.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[extend nl80211 description a bit, fix typo]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was possible to break interface combinations in
the following way:
combo 1: iftype = AP, num_ifaces = 2, num_chans = 2,
combo 2: iftype = AP, num_ifaces = 1, num_chans = 1, radar = HT20
With the above interface combinations it was
possible to:
step 1. start AP on DFS channel by matching combo 2
step 2. start AP on non-DFS channel by matching combo 1
This was possible beacuse (step 2) did not consider
if other interfaces require radar detection.
The patch changes how cfg80211 tracks channels -
instead of channel itself now a complete chandef
is stored.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When receiving an IBSS_JOINED event select the BSS object
based on the {bssid, channel} couple rather than the bssid
only.
With the current approach if another cell having the same
BSSID (but using a different channel) exists then cfg80211
picks up the wrong BSS object.
The result is a mismatching channel configuration between
cfg80211 and the driver, that can lead to any sort of
problem.
The issue can be triggered by having an IBSS sitting on
given channel and then asking the driver to create a new
cell using the same BSSID but with a different frequency.
By passing the channel to cfg80211_get_bss() we can solve
this ambiguity and retrieve/create the correct BSS object.
All the users of cfg80211_ibss_joined() have been changed
accordingly.
Moreover WARN when cfg80211_ibss_joined() gets a NULL
channel as argument and remove a bogus call of the same
function in ath6kl (it does not make sense to call
cfg80211_ibss_joined() with a zero BSSID on ibss-leave).
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Cc: libertas-dev@lists.infradead.org
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[minor code cleanup in ath6kl]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For better use of CPU idle time, allow the scheduler to select the CPU
on which the timeout work of regulatory settings would be executed.
This extends CPU idle residency time and saves power.
This functionality is enabled when CONFIG_WQ_POWER_EFFICIENT is selected.
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Shaibal Dutta <shaibal.dutta@broadcom.com>
[zoran.markovic@linaro.org: Rebased to latest kernel. Added commit message.]
Signed-off-by: Zoran Markovic <zoran.markovic@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add helper function that will return regdomain.
Follow the driver's regulatory domain, if present,
unless a country IE has been processed or a user
wants to help compliance further.
Signed-off-by: Janusz Dziedzic <janusz.dziedzi@tieto.com>
[remove useless reg variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set preset_chandef in channel switch notification.
In other case we will have old preset_chandef.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The scheduled scan matchsets were intended to be a list of filters,
with the found BSS having to pass at least one of them to be passed
to the host. When the RSSI attribute was added, however, this was
broken and currently wpa_supplicant adds that attribute in its own
matchset; however, it doesn't intend that to mean that anything
that passes the RSSI filter should be passed to the host, instead
it wants it to mean that everything needs to also have higher RSSI.
This is semantically problematic because we have a list of filters
like [ SSID1, SSID2, SSID3, RSSI ] with no real indication which
one should be OR'ed and which one AND'ed.
To fix this, move the RSSI filter attribute into each matchset. As
we need to stay backward compatible, treat a matchset with only the
RSSI attribute as a "default RSSI filter" for all other matchsets,
but only if there are other matchsets (an RSSI-only matchset by
itself is still desirable.)
To make driver implementation easier, keep a global min_rssi_thold
for the entire request as well. The only affected driver is ath6kl.
I found this when I looked into the code after Raja Mani submitted
a patch fixing the n_match_sets calculation to disregard the RSSI,
but that patch didn't address the semantic issue.
Reported-by: Raja Mani <rmani@qti.qualcomm.com>
Acked-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few cases, e.g. suspend, where an AP interface is
stopped by the kernel rather than by userspace request, most
commonly when suspending. To let userspace know about this,
send the NL80211_CMD_STOP_AP command as an event every time
an AP interface is stopped. This also happens when userspace
did in fact request the AP stop, but that's not a problem.
For full-MAC drivers this may need to be extended to also
cover cases where the device stopped the AP operation for
some reason, this a bit more complicated because then all
cfg80211 state also needs to be reset; such API is not part
of this patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there's a policy, then nla_parse() return values must be
checked, otherwise the policy is useless and there's nothing
that ensures the attributes are actually what we expect them
to be.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Before allowing userspace to initiate a channel switch, check
that it's actually connected in some sense. Also use a more
appropriate error code for the not connected case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix the following issues in reg_process_hint():
1. Add verification that wiphy is valid before processing
NL80211_REGDOMAIN_SET_BY_COUNTRY_IE.
2. Free the request in case of invalid initiator.
3. Remove WARN_ON check on reg_request->alpha2 as it is not a
pointer.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow to force SGI, LGI.
Mainly for test purpose.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Addition of the frequency hints showed up couple of places in cfg80211
where pointers could be marked const and a shared function could be used
to fetch a valid channel.
Signed-off-by: Jouni Malinen <j@w1.fi>
[fix mwifiex]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows drivers to advertise the maximum number of associated
stations they support in AP mode (including P2P GO). User space
applications can use this for cleaner way of handling the limit (e.g.,
hostapd rejecting IEEE 802.11 authentication without manual
configuration of the limit) or to figure out what type of use cases can
be executed with multiple devices before trying and failing.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This clarifies the expected driver behavior on the older
NL80211_ATTR_MAC and NL80211_ATTR_WIPHY_FREQ attributes and adds a new
set of similar attributes with _HINT postfix to enable use of a
recommendation of the initial BSS to choose. This can be helpful for
some drivers that can avoid an additional full scan on connection
request if the information is provided to them (user space tools like
wpa_supplicant already has that information available based on earlier
scans).
In addition, this can be used to get more expected behavior for cases
where a specific BSS should be picked first based on operations like
Interworking network selection or WPS. These cases were already easily
addressed with drivers that leave BSS selection to user space, but there
was no convenient way to do this with drivers that take care of BSS
selection internally without using the NL80211_ATTR_MAC which is not
really desired since it is needed for other purposes to force the
association to remain with the same BSS.
Signed-off-by: Jouni Malinen <j@w1.fi>
[add const, fix policy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As __cfg80211_rdev_from_attrs(), nl80211_dump_wiphy_parse() and
nl80211_set_wiphy() are all under rtnl_lock protection,
__dev_get_by_index() instead of dev_get_by_index() should be used
to find interface handler in them allowing us to avoid to change
interface reference counter.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The REGULATORY_CUSTOM_REG can be used during early init with
the goal of overriding the wiphy's default regulatory settings
in case the alpha2 of the device is not known. In the case that
the alpha2 becomes known lets avoid having drivers having to
clear the REGULATORY_CUSTOM_REG flag by doing it for them
when regulatory_hint() is used.
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Block setting the wrong values through iwconfig retry
command. Add sanity checking before sending the retry
limit to the driver.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a utility function to get the number of channels supported by
the device, and update the places in the code that need this data.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
[replace another occurrence in libertas, fix kernel-doc, fix bugs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While getting the retry limit, wext-compat returns the value
without updating the flag for retry->flags is 0. Also in this
case, it updates long retry flag when short and long retry
value are unequal.
So, iwconfig never showing "Retry short limit" and showing
"Retry long limit" when both values are unequal.
Updated the flags and corrected the condition properly.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The vendor/testmode event skb functions are needed outside
the ifdef for vendor-specific events, so move them out.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the RTNL can't always be held, use wdev/sdata locking for
the qos-map dereference in mac80211. This requires cfg80211 to
consistently lock it, which it was missing in one place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows QoS mapping from external networks to be implemented as
defined in IEEE Std 802.11-2012, 10.24.9. APs can use this to advertise
DSCP ranges and exceptions for mapping frames to a specific UP over
Wi-Fi.
The payload of the QoS Map Set element (IEEE Std 802.11-2012, 8.4.2.97)
is sent to the driver through the new NL80211_ATTR_QOS_MAP attribute to
configure the local behavior either on the AP (based on local
configuration) or on a station (based on information received from the
AP).
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In addition to vendor-specific commands, also support vendor-specific
events. These must be registered with cfg80211 before they can be used.
They're also advertised in nl80211 in the wiphy information so that
userspace knows can be expected. The events themselves are sent on a
new multicast group called "vendor".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add VHT MCS/NSS set support for nl80211_set_tx_bitrate_mask().
This should be used mainly for test purpose, to check
different MCS/NSS VHT combinations.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Evan Huus found (by fuzzing in wireshark) that the radiotap
iterator code can access beyond the length of the buffer if
the first bitmap claims an extension but then there's no
data at all. Fix this.
Cc: stable@vger.kernel.org
Reported-by: Evan Huus <eapache@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
___cfg80211_scan_done() can be called in some cases
(e.g. on NETDEV_DOWN) before the low level driver
notified scan completion (which is indicated by
passing leak=true).
Clearing rdev->scan_req in this case is buggy, as
scan_done_wk might have already being queued/running
(and can't be flushed as it takes rtnl()).
If a new scan will be requested at this stage, the
scan_done_wk will try freeing it (instead of the
previous scan), and this will later result in
a use after free.
Simply remove the "leak" option, and replace it with
a standard WARN_ON.
An example backtrace after such crash:
Unable to handle kernel paging request at virtual address fffffee5
pgd = c0004000
[fffffee5] *pgd=9fdf6821, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] SMP ARM
PC is at cfg80211_scan_done+0x28/0xc4 [cfg80211]
LR is at __ieee80211_scan_completed+0xe4/0x2dc [mac80211]
[<bf0077b0>] (cfg80211_scan_done+0x28/0xc4 [cfg80211])
[<bf0973d4>] (__ieee80211_scan_completed+0xe4/0x2dc [mac80211])
[<bf0982cc>] (ieee80211_scan_work+0x94/0x4f0 [mac80211])
[<c005fd10>] (process_one_work+0x1b0/0x4a8)
[<c0060404>] (worker_thread+0x138/0x37c)
[<c0066d70>] (kthread+0xa4/0xb0)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_leave stops sched scan when any station vif
is leaving. Add an explicit check and call it only
when the relevant vif (the one we scan on) is leaving.
Signed-off-by: Barak Bercovitz <barak@wizery.com>
[Eliad - changed the commit message a bit]
Signed-off-by: Eliad Peller <eliad@wizery.com>
[Johannes - add ASSERT_RTNL since that protects the pointer]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rename NL80211_TXRATE_MCS to NL80211_TXRATE_HT and also
rename mcs to ht_mcs in struct cfg80211_bitrate_mask.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow setting the bitrate masks back to default by
omitting the NL80211_ATTR_TX_RATES attribute.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[rephrase commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211 allows re-association in managed mode and if a user
wants to re-associate to the same AP network after the time
period of IEEE80211_SCAN_RESULT_EXPIRE, cfg80211 warns with
the following message on receiving the connect result event.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 13984 at net/wireless/sme.c:658
__cfg80211_connect_result+0x3a6/0x3e0 [cfg80211]()
Call Trace:
[<ffffffff81747a41>] dump_stack+0x46/0x58
[<ffffffff81045847>] warn_slowpath_common+0x87/0xb0
[<ffffffff81045885>] warn_slowpath_null+0x15/0x20
[<ffffffffa05345f6>] __cfg80211_connect_result+0x3a6/0x3e0 [cfg80211]
[<ffffffff8107168b>] ? update_rq_clock+0x2b/0x50
[<ffffffff81078c01>] ? update_curr+0x1/0x160
[<ffffffffa05133d2>] cfg80211_process_wdev_events+0xb2/0x1c0 [cfg80211]
[<ffffffff81079303>] ? pick_next_task_fair+0x63/0x170
[<ffffffffa0513518>] cfg80211_process_rdev_events+0x38/0x90 [cfg80211]
[<ffffffffa050f03d>] cfg80211_event_work+0x1d/0x30 [cfg80211]
[<ffffffff8105f21f>] process_one_work+0x17f/0x420
[<ffffffff8105f90a>] worker_thread+0x11a/0x370
[<ffffffff8105f7f0>] ? rescuer_thread+0x2f0/0x2f0
[<ffffffff8106638b>] kthread+0xbb/0xc0
[<ffffffff810662d0>] ? kthread_create_on_node+0x120/0x120
[<ffffffff817574bc>] ret_from_fork+0x7c/0xb0
[<ffffffff810662d0>] ? kthread_create_on_node+0x120/0x120
---[ end trace 61f3bddc9c4981f7 ]---
The reason is that, in connect result event cfg80211 unholds
the BSS to which the device is associated (and was held so
far). So, for the event with status successful, when cfg80211
wants to get that BSS from the device's BSS list it gets a
NULL BSS because the BSS has been expired and unheld already.
Fix it by reshuffling the code.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This permits the use of DFS channel once the CAC is conducted and
no radar is detected.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for vendor-specific commands to nl80211. This is
intended to be used for really vendor-specific functionality
that can't be implemented in a generic fashion for any reason.
It's *NOT* intended to be used for any normal/generic feature
or any optimisations that could be implemented across drivers.
Currently, only vendor commands (with replies) are supported,
no dump operations or vendor-specific notifications.
Also add a function wdev_to_ieee80211_vif() to mac80211 which
is needed for mac80211-based drivers wanting to implement any
vendor commands.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Don't clear cfg80211_bitrate_mask twice in
nl80211_set_tx_bitrate_mask() function.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check the DFS region before channel availability check.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be used outside of the regulatory context for any checks
on the DFS region. The central cfg80211 dfs_region is always used
and if it does not match with the wiphy a debug print is issued.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This attribute is needed for setting Operating Mode Notification
in AP mode from User Space. This functionality is required when
User Space received Assoc Request contains Operation Mode
Notification element.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
[fix typos, nl80211 documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel switch announcement code has some major locking problems
which can cause a deadlock in worst case. A series of fixes has been
proposed, but these are non-trivial and need to be tested first.
Therefore disable CSA completely for 3.13.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel switch notification should be sent under the
wdev/sdata-lock, preferably in the same moment as the channel change
happens, to avoid races by other callers (e.g. start/stop_ap).
This also adds the previously missing sdata_lock protection in
csa_finalize_work.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To avoid race conditions in functions which modify the beacon
information, lock these using the wdev lock. This is especially required
to avoid problems for csa handling functions which modify beacons but
can not be called under rtnl lock.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change cfg80211 and mac80211 to use cfg80211_mgmt_tx_params
struct to aggregate parameters for mgmt_tx functions.
This makes the functions' signatures less clumsy and allows
less painful parameters extension.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
[fix all other drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
nla_put_flag needs a real nl80211 attribute id, not a wiphy flag bit.
While at it, split 5 and 10 MHz capability flags in case we ever need
to support hardware that can only do one of the two.
Also move the flag settings to the split-only information so we don't
increase the space needed for old userspace.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[change location of flag setting]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This lets us later reuse the more generic reg_dfs_region_str().
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Only allow DFS to be set if the DFS regions agree.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
u8 was used in some other places, just stick to the enum,
this forces us to express the values that are expected.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Certain vendors may want to disable the processing of
country IEs so that they can continue using the regulatory
domain the driver or user has set. Currently there is no
way to stop the core from processing country IEs, so add
support to the core to ignore country IE hints.
Cc: Mihir Shete <smihir@qti.qualcomm.com>
Cc: Henri Bahini <hbahini@qca.qualcomm.com>
Cc: Tushnim Bhattacharyya <tushnimb@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
802.11 cards may have different country IE parsing behavioural
preferences and vendors may want to support these. These preferences
were managed by the REGULATORY_CUSTOM_REG and the REGULATORY_STRICT_REG
flags and their combination. Instead of using this existing notation,
split out the country IE behavioural preferences as a new flag. This
will allow us to add more customizations easily and make the code more
maintainable.
Cc: Mihir Shete <smihir@qti.qualcomm.com>
Cc: Henri Bahini <hbahini@qca.qualcomm.com>
Cc: Tushnim Bhattacharyya <tushnimb@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[fix up conflicts]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reflects that case is now completely separated.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This splits up the driver regulatory update on its
own, this helps simplify the reading the case.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This splits out the user regulatory update on its
own, this helps simplify reading the case.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This splits up the core regulatory update to be
set on its own helper. This should make it easier
to read exactly what type of requests should be
expected there. In this case its clear that
NL80211_REGDOM_SET_BY_CORE is only used by the
core for updating the world regulatory domain.
This is consistant with the nl80211.h documentation.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[add warning to default switch case to avoid compiler warning]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
last_request is RCU protected, since we're getting it
on set_regdom() we might as well pass it to ensure the
same request is being processed, otherwise there is a
small race it could have changed. This makes processing
of the request atomic.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers that set the WIPHY_FLAG_CUSTOM_REGULATORY skip
the core world regulatory domain updates, but do want
their reg_notifier() called. Move the check for this
closer to the source of the check that detected skipped
was required and while at it add a helper for the notifier
calling. This has no functional changes. This brings together
the place where we call the reg_notifier() will be called.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It seems some out of tree drivers were using a regulatory_hint("00")
to trigger off the wiphy regulatory notifier, for those cases just
setting the WIPHY_FLAG_CUSTOM_REGULATORY would suffice to call
the reg_notifier() for a world regulatory domain update. If drivers
find other needs for calling the reg_notifier() a proper implemenation
is preferred.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All the regulatory request process routines use the
same pattern.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enforces proper RCU APIs accross the code.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is common code, this reduces the chance of making
a mistake of how we free it.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By dealing with non country IE conficts first we can shift
the code that deals with the conflict to the left. This has
no functional changes.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is the last split up of the old unified __regultory_hint()
processing set of functionality, it moves the country IE processing
all on its own. This makes it easier to follow and read what exactly
is going on for the case of processing country IEs.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes the code easier to read and follow.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes the code path easier to read and lets us
split out some functionality that is only user specific,
that makes it easier to read the other types of requests.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes the code path easier to read for the core case.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[add warning to default case in switch to avoid compile warning]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently nl80211 allows userspace to send the kernel
a bogus regulatory domain with at most 32 rules set
and it won't reject it until after its allocated
memory. Let's be smart about it and take advantage
that the last_request is now available under RTNL
and check if the alpha2 matches an expected request
and reject any bogus userspace requests prior to
hitting the memory allocator.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a custom regulatory domain is passed and if a rule for a
channel indicates it should be disabled that channel should
always remain disabled as per its documentation and design.
Likewise if WIPHY_FLAG_STRICT_REGULATORY flag is set and a
regulatory_hint() is issued if a channel is disabled that
channel should remain disabled.
Without this change only drivers that set the _orig flags
appropriately on their own would ensure disallowed channels
remaind disabled. This helps drivers save code by relying on
the APIS provided to entrust channels that should not be enabled
be respected by only having to use wiphy_apply_custom_regulatory()
or regulatory_hint() with the WIPHY_FLAG_STRICT_REGULATORY set.
If wiphy_apply_custom_regulatory() is used together with
WIPHY_FLAG_STRICT_REGULATORY and a regulatory_hint() issued
later, the incoming regulatory domain can override previously
set _orig parameters from the initial custom regulatory
setting.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If genregdb.awk assumes the file will end with an
extra empty line or a comment line. This is could
not be true so just address this.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This has no functional change, this just lets us reuse
helpers at a later time.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow beconing after we pass Channel Availability Check (CAC).
Allow non-DFS and DFS channels mix. All DFS channels have to
be in NL80211_DFS_AVAILABLE state (pass CAC).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To report channel width correctly we have
to send correct channel parameters from
mac80211 when calling cfg80211_cac_event().
This is required in case of using channel width
higher than 20MHz and we have to set correct
dfs channel state after CAC (NL80211_DFS_AVAILABLE).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the flag is entirely implemented in cfg80211, it should
have been a global feature flag (which I believe didn't
exist at the time). However, there's no reason to allow
drivers to unset the flag, so don't allow it and remove
the validation of NL80211_SCAN_FLAG_FLUSH.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Improve readability of the function by adding the break,
there's no functional impact but it's confusing to fall
through.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The iniator is already available to us, so use it.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wiphy_apply_custom_regulatory() implies WIPHY_FLAG_CUSTOM_REGULATORY
but we never enforced it, do that now and warn if the driver
didn't set it. All drivers should be following this today already.
Having WIPHY_FLAG_CUSTOM_REGULATORY does not however mean you will
use wiphy_apply_custom_regulatory() though, you may have your own
_orig value set up tools / helpers. The intel drivers are examples
of this type of driver.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check chandef we get in CAC request is usable for CAC.
All channels have to be DFS channels. Allow DFS_USABLE
and DFS_AVAILABLE channels mix. At least one channel
has to be DFS_USABLE (require CAC).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add helper fuctions for start/end freq.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These two flags are used for the same purpose, just
combine them into a no-ir flag to annotate no initiating
radiation is allowed.
Old userspace sending either flag will have it treated as
the no-ir flag. To be considerate to older userspace we
also send both the no-ir flag and the old no-ibss flags.
Newer userspace will have to be aware of older kernels.
Update all places in the tree using these flags with the
following semantic patch:
@@
@@
-NL80211_RRF_PASSIVE_SCAN
+NL80211_RRF_NO_IR
@@
@@
-NL80211_RRF_NO_IBSS
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_PASSIVE_SCAN
+IEEE80211_CHAN_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IBSS
+IEEE80211_CHAN_NO_IR
@@
@@
-NL80211_RRF_NO_IR | NL80211_RRF_NO_IR
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IR | IEEE80211_CHAN_NO_IR
+IEEE80211_CHAN_NO_IR
@@
@@
-(NL80211_RRF_NO_IR)
+NL80211_RRF_NO_IR
@@
@@
-(IEEE80211_CHAN_NO_IR)
+IEEE80211_CHAN_NO_IR
Along with some hand-optimisations in documentation, to
remove duplicates and to fix some indentation.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[do all the driver updates in one go]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes wpa_supplicant p2p_find on 5GHz-only devices
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to nl80211 API breakage, 5/10 MHz support is broken for
all drivers. Fixing it requires adding new API, but that
can't be done as a bugfix commit since that would require
either updating all APIs in the trees needing the bugfix or
cause different kernels to have incompatible API.
Therefore, just disable 5/10 MHz support for all drivers.
Cc: stable@vger.kernel.org [3.12]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Coverity pointed out that we might dereference NULL later
if nla_nest_start() returns a failure. This isn't really
true since we'd bomb out before, but we should check the
return value directly, so do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Coverity pointed out that in the (practically impossible)
error case we leak the message - fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Coverity pointed out that in a few functions we don't
check the return value of the nla_put_*() calls. Most
of these are fairly harmless because the input isn't
very dynamic and controlled by the kernel, but the
pattern is simply wrong, so fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The wext internal chandefs for ibss should be created using the
cfg80211_chandef_create() functions. Initializing fields manually is
error-prone.
Reported-by: Dirk Gouders <dirk@gouders.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Register generic netlink multicast groups as an array with
the family and give them contiguous group IDs. Then instead
of passing the global group ID to the various functions that
send messages, pass the ID relative to the family - for most
families that's just 0 because the only have one group.
This avoids the list_head and ID in each group, adding a new
field for the mcast group ID offset to the family.
At the same time, this allows us to prevent abusing groups
again like the quota and dropmon code did, since we can now
check that a family only uses a group it owns.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This doesn't really change anything, but prepares for the
next patch that will change the APIs to pass the group ID
within the family, rather than the global group ID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by David Miller, make genl_register_family_with_ops()
a macro and pass only the array, evaluating ARRAY_SIZE() in the
macro, this is a little safer.
The openvswitch has some indirection, assing ops/n_ops directly in
that code. This might ultimately just assign the pointers in the
family initializations, saving the struct genl_family_and_ops and
code (once mcast groups are handled differently.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that genl_ops are no longer modified in place when
registering, they can be made const. This patch was done
mostly with spatch:
@@
identifier ops;
@@
+const
struct genl_ops ops[] = {
...
};
(except the struct thing in net/openvswitch/datapath.c)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow making the ops array const by not modifying the ops
flags on registration but rather only when ops are sent
out in the family information.
No users are updated yet except for the pre_doit/post_doit
calls in wireless (the only ones that exist now.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nl80211 attribute NL80211_ATTR_CSA_C_OFF_BEACON should be nested
inside NL80211_ATTR_CSA_IES, but commit ee4bc9e758
("nl80211: enable IBSS support for channel switch announcements")
added a check in the outer message attributes.
Fix channel switch calls by removing the erroneus condition.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement the required procedures for mesh channel switching as defined
in the IEEE Std 802.11-2012 section 10.9.8.4.3 and also handle the CSA
and MCSP elements as followed:
* Add the function for updating the beacon and probe response frames
with CSA and MCSP elements during the period of switching to the new
channel. Both CSA and MCSP elements must be included in beacon and
probe response frames until the intended channel switch time.
* The ifmsh->csa_settings is set to NULL and the CSA and MCSP elements
will then be removed from the beacon or probe response frames once the
new channel is switched to.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow the triggering of CSA frame using mesh interface. The
rules are more or less same with IBSS, such as not allowed to
change between the band and channel width has to be same from
the previous mode. Also, move the ieee80211_send_action_csa
to a common space so that it can be re-used by mesh interface.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tomasz Bursztyka