Rename mii_lpa_to_linkmode_lpa_t to mii_lpa_mod_linkmode_lpa_t to
indicate it modifies the passed linkmode bitmap, without clearing any
other bits.
Also, ensure bit are clear which the lpa indicates should not be set.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename mii_stat1000_to_linkmode_lpa_t to
mii_stat1000_mod_linkmode_lpa_t to indicate it modifies the passed
linkmode bitmap, without clearing any other bits.
Add a helper to set/clear bits in a linkmode.
Use this helper to ensure bit are clear which the stat1000 indicates
should not be set.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
mii_adv_to_linkmode_adv_t() clears all bits before setting it needs to
set. This means the freshly set Autoneg gets cleared.
Change the order, and add comments about it clearing the old content
of the bitmap.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/networking/ is full of cryptically named files with
driver documentation. This makes finding interesting information
at a glance really hard. Move all those files into a directory
called device_drivers (since not all drivers are for device) and
fix up references.
RFC v0.1 -> RFC v1:
- also add .txt suffix to the files which are missing it (Quentin)
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: David Ahern <dsahern@gmail.com>
Acked-by: Henrik Austad <henrik@austad.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP_NOTSENT_LOWAT socket option or sysctl was added in linux-3.12
as a step to enable bigger tcp sndbuf limits.
It works reasonably well, but the following happens :
Once the limit is reached, TCP stack generates
an [E]POLLOUT event for every incoming ACK packet.
This causes a high number of context switches.
This patch implements the strategy David Miller added
in sock_def_write_space() :
- If TCP socket has a notsent_lowat constraint of X bytes,
allow sendmsg() to fill up to X bytes, but send [E]POLLOUT
only if number of notsent bytes is below X/2
This considerably reduces TCP_NOTSENT_LOWAT overhead,
while allowing to keep the pipe full.
Tested:
100 ms RTT netem testbed between A and B, 100 concurrent TCP_STREAM
A:/# cat /proc/sys/net/ipv4/tcp_wmem
4096 262144 64000000
A:/# super_netperf 100 -H B -l 1000 -- -K bbr &
A:/# grep TCP /proc/net/sockstat
TCP: inuse 203 orphan 0 tw 19 alloc 414 mem 1364904 # This is about 54 MB of memory per flow :/
A:/# vmstat 5 5
procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu-----
r b swpd free buff cache si so bi bo in cs us sy id wa st
0 0 0 256220672 13532 694976 0 0 10 0 28 14 0 1 99 0 0
2 0 0 256320016 13532 698480 0 0 512 0 715901 5927 0 10 90 0 0
0 0 0 256197232 13532 700992 0 0 735 13 771161 5849 0 11 89 0 0
1 0 0 256233824 13532 703320 0 0 512 23 719650 6635 0 11 89 0 0
2 0 0 256226880 13532 705780 0 0 642 4 775650 6009 0 12 88 0 0
A:/# echo 2097152 >/proc/sys/net/ipv4/tcp_notsent_lowat
A:/# grep TCP /proc/net/sockstat
TCP: inuse 203 orphan 0 tw 19 alloc 414 mem 86411 # 3.5 MB per flow
A:/# vmstat 5 5 # check that context switches have not inflated too much.
procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu-----
r b swpd free buff cache si so bi bo in cs us sy id wa st
2 0 0 260386512 13592 662148 0 0 10 0 17 14 0 1 99 0 0
0 0 0 260519680 13592 604184 0 0 512 13 726843 12424 0 10 90 0 0
1 1 0 260435424 13592 598360 0 0 512 25 764645 12925 0 10 90 0 0
1 0 0 260855392 13592 578380 0 0 512 7 722943 13624 0 11 88 0 0
1 0 0 260445008 13592 601176 0 0 614 34 772288 14317 0 10 90 0 0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
====================
net/sched: act_tunnel_key: support key-less tunnels
This short series from Adi Nissim allows to support key-less tunnels
by the tc tunnel key actions, which is needed for some GRE use-cases.
changes from V0:
- addresses build warning spotted by kbuild, make sure to always init
to zero the tunnel key
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible to set a tunnel without a destination port. However,
on dump(), a zero dst port is returned to user space even if it was not
set, fix that.
Note that so far it wasn't required, b/c key less tunnels were not
supported and the UDP tunnels do require destination port.
Signed-off-by: Adi Nissim <adin@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow setting a tunnel without a tunnel key. This is required for
tunneling protocols, such as GRE, that define the key as an optional
field.
Signed-off-by: Adi Nissim <adin@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a DP_NOTICE message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Add one-armed router support
Up until now, when a packet was routed by the ASIC through the same
router interface (RIF) from which it ingressed from, the ASIC passed the
sole copy of the packet to the kernel. This allowed the kernel to route
the packet and also potentially generate an ICMP redirect.
There are scenarios (e.g., "one-armed router") where packets are
intentionally routed this way and are therefore not deemed as
exceptions. In such scenarios the current method of trapping packets to
the CPU is problematic, as it results in major packet loss.
This patchset solves the problem by having the ASIC forward the packet,
but also send a copy to the CPU, which gives the kernel the opportunity
to generate required exceptions.
To prevent the kernel from forwarding such packets again, the driver
marks them with 'offload_l3_fwd_mark', which causes the kernel to
consume them in ip{,6}_forward_finish().
Patch #1 renames 'offload_mr_fwd_mark' to 'offload_l3_fwd_mark'. When
set, the field indicates that a packet was already forwarded in L3
(unicast / multicast) by a capable device.
Patch #2 teaches the kernel to consume unicast packets that have
'offload_l3_fwd_mark' set.
Patch #3 changes mlxsw to mirror loopbacked (iRIF == eRIF) packets,
instead of trapping them.
Patch #4 adds a test case for above mentioned scenario.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Construct a "one-armed router" topology and test that packets are
forwarded by the ASIC and that a copy of the packet is sent to the
kernel, which does not forward the packet again.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ASIC detects that a unicast packet is routed through the same
router interface (RIF) from which it ingressed (iRIF == eRIF), it raises
a trap called loopback error (LBERROR).
Thus far, this trap was configured to send a sole copy of the packet to
the CPU so that ICMP redirect packets could be potentially generated by
the kernel.
This is problematic as the CPU cannot forward packets at 3.2Tb/s and
there are scenarios (e.g., "one-armed router") where iRIF == eRIF is not
an exception.
Solve this by changing the trap to send a copy of the packet to the CPU.
To prevent the kernel from forwarding the packet again, it is marked
with 'offload_l3_fwd_mark'.
The trap is configured in a trap group of its own with a dedicated
policer in order not to prevent packets trapped by other traps from
reaching the CPU.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets marked with 'offload_l3_fwd_mark' were already forwarded by a
capable device and should not be forwarded again by the kernel.
Therefore, have the kernel consume them.
The check is performed in ip{,6}_forward_finish() in order to allow the
kernel to process such packets in ip{,6}_forward() and generate required
exceptions. For example, ICMP redirects.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit abf4bb6b63 ("skbuff: Add the offload_mr_fwd_mark field") added
the 'offload_mr_fwd_mark' field to indicate that a packet has already
undergone L3 multicast routing by a capable device. The field is used to
prevent the kernel from forwarding a packet through a netdev through
which the device has already forwarded the packet.
Currently, no unicast packet is routed by both the device and the
kernel, but this is about to change by subsequent patches and we need to
be able to mark such packets, so that they will no be forwarded twice.
Instead of adding yet another field to 'struct sk_buff', we can just
rename 'offload_mr_fwd_mark' to 'offload_l3_fwd_mark', as a packet
either has a multicast or a unicast destination IP.
While at it, add a comment about both 'offload_fwd_mark' and
'offload_l3_fwd_mark'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan says:
====================
mlx4_core cleanups
This patchset by Erez contains cleanups to the mlx4_core driver.
Patch 1 replaces -EINVAL with -EOPNOTSUPP for unsupported operations.
Patch 2 fixes some coding style issues.
Series generated against net-next commit:
97e6c858a2 net: usb: aqc111: Initialize wol_cfg with memset in aqc111_suspend
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix 3 checkpatch errors within mlx4/main.c:
- Unnecessary mlx4_debug_level global variable initialization to 0.
- Prohibited space before comma.
- Whitespaces instead of tab.
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions __set_port_type and mlx4_check_port_params returned
-EINVAL while the proper return code is -EOPNOTSUPP as a
result of an unsupported operation. All drivers should generate
this and all users should check for it when detecting an
unsupported functionality.
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Logic of phy_device_create() requests PHY modules according to PHY ID
but for C45 PHYs we use different field for the IDs.
Let's also request the modules for these IDs.
Changes from v1:
- Only request C22 modules if C45 are not present (Andrew)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Joao Pinto <joao.pinto@synopsys.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jerin Jacob says:
====================
octeontx2-af: NIX and NPC enhancements
This patchset is a continuation to earlier submitted four patch
series to add a new driver for Marvell's OcteonTX2 SOC's
Resource virtualization unit (RVU) admin function driver.
1. octeontx2-af: Add RVU Admin Function driver
https://www.spinics.net/lists/netdev/msg528272.html
2. octeontx2-af: NPA and NIX blocks initialization
https://www.spinics.net/lists/netdev/msg529163.html
3. octeontx2-af: NPC parser and NIX blocks initialization
https://www.spinics.net/lists/netdev/msg530252.html
4. octeontx2-af: NPC MCAM support and FLR handling
https://www.spinics.net/lists/netdev/msg534392.html
This patch series adds support for below
NPC block:
- Add NPC(mkex) profile support for various Key extraction configurations
NIX block:
- Enable dynamic RSS flow key algorithm configuration
- Enhancements on Rx checksum and error checks
- Add support for Tx packet marking support
- TL1 schedule queue allocation enhancements
- Add LSO format configuration mbox
- VLAN TPID configuration
- Skip multicast entry init for broadcast tables
v2:
- Rename FLOW_* to NIX_FLOW_* to avoid serious global namespace collisions,
as we have various FLOW_* definitions coming from
include/uapi/linux/pkt_cls.h for example.(David Miller)
- Pack the arguments of rvu_get_tl1_schqs() function
as 80 columns allows.(David Miller)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The following set of NPC registers allow the driver to configure NPC
to generate different key value schemes to compare against packet
payload in MCAM search.
NPC_AF_INTF(0..1)_KEX_CFG
NPC_AF_KEX_LDATA(0..1)_FLAGS_CFG
NPC_AF_INTF(0..1)_LID(0..7)_LT(0..15)_LD(0..1)_CFG
NPC_AF_INTF(0..1)_LDATA(0..1)_FLAGS(0..15)_CFG
Currently, the AF driver populates these registers to
configure the default values to address the most common
use cases such as key generation for channel number + DMAC.
The secure firmware stores different configuration
value of these registers to enable different NPC use case
along with the name for the lookup.
Patch loads profile binary from secure firmware over
the exiting CGX mailbox interface and apply the profile.
AF driver shall fall back to the default configuration
in case of any errors.
The AF consumer driver can know the selected profile
on response to NPC_GET_KEX_CFG mailbox by introducing
mkex_pfl_name in the struct npc_get_kex_cfg_rsp.
Signed-off-by: Vamsi Attunuru <vamsi.attunuru@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIX_AF_LSO_FORMAT(0..31)_FIELD(0..7) register enables an SW defined
means to define LSO packet modification formats.
0..31 works as an index to choose the algorithm, On success, the mailbox
returns the index to the client of chosen LSO algorithm selection.
This index will be used in configuring the transmit descriptors.
Add mailbox interface to dynamically reserve and configure LSO format.
This commit also fixes 'sizem1' for NIX_LSOALG_TCP_FLAGS
to '1' i.e 2 Bytes.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds mailbox support for L4 checksum verification
and L3 and L4 length verification configuration.
Signed-off-by: Vidhya Raman <vraman@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setup TPID's for vlan0 and vlan1 for Tx VLAN insertion offloads.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIX_AF_MARK_FORMAT(0..127)_CTL register enables an SW defined
means to mark/insert various data in the packet based on
final packet color from traffic shaping HW.
0..127 works as an index to choose the algorithm. On success,
the mailbox returns the index to the client.
Add NIX_MARK_FORMAT_CFG mailbox which reserves mark format based on
tuple (offset, y_mask, y_val, r_mask, r_val)
If the tuple is requested again for mark format that was already
reserved, then it will be reused. If not it will reserve a new entry
if space is available.
Also on AF init commonly used marker format such as VLAN DEI, IPv4
ECN, IPv4 DSCP are reserved for AF consumers.
Signed-off-by: Krzysztof Kanas <kkanas@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for enabling RSS in promiscuous mode
if RSS is already requested by the AF client.
Signed-off-by: Vamsi Attunuru <vamsi.attunuru@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support all NIX specific valid length errors and
checksum errors on Rx, Update all NIX_AF_RX_DEF_* registers.
Also sorted all registers in HRM definition order.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the inner IPv4 checksum and
defines the error code for Rx inner and outer checksum errors.
Setting ERRCODE as 1 so that CQE descriptor can be embedded
valid checksum error code and the driver can interpret
checksum error as ERRLEV = LID + 1 and ERRCODE = 1.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default behavior was to free all the TLx Tx schedule
queues. This patch adds support for freeing a single Tx
schedule queue if TXSCHQ_FREE_ALL flag is not set.
Signed-off-by: Krzysztof Kanas <kkanas@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TL1 is the root node in the scheduling hierarchy and
it is a global resource with a limited number.
This patch introduces restriction and validation on
the allocation of the TL1 nodes for the effective resource
sharing across the AF consumers.
- Limit TL1 allocation to 2 per lmac.
One could be for the normal link and one for IEEE802.3br
express link (Express Send DMA).
Effectively all the VF's of an RVU PF(lmac) share the two TL1 schqs.
- TL1 cannot be freed once allocated.
- Allow VF's to only apply default config to TL1 if not
already applied. PF's can always overwrite the TL1 config.
- Consider NIX_AQ_INSTOP_WRITE while validating txschq
when sq.ena is set.
Signed-off-by: Krzysztof Kanas <kkanas@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduced reserve_flowkey_alg_idx()to reserve RSS algorithm index,
it would internally use set_flowkey_fields() to generate fields
based on the flow key dynamically.
On AF driver init, it would reserve a predefined set RSS algo indexes,
which will be available all the time for all the AF driver consumers.
The leftover algo indexes can be reserved at runtime through
exiting nix_rss_flowkey_cfg mailbox message.
The NIX_FLOW_KEY_TYPE_PORT is removed from predefined a set of RSS flow
type as it is not used by any consumer.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce state-based algorithm to convert the flow_key value
to RSS algo field used by NIX_AF_RX_FLOW_KEY_ALGX_FIELDX register.
The outer `for loop` goes over _all_ protocol field and the following
variables depict the state machine forward progress logic.
a) keyoff_marker - Enabled when hash byte length needs to be accounted
in field->key_offset update.
b) field_marker - Enabled when a new field needs to be selected.
c) group_member - Enabled when a protocol is part of a group.
This would remove the existing hard coding and enable to add
new protocol support seamlessly.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added response for nix_rss_flowkey_cfg message to return
selected RSS algorithm index.
The FLOW_KEY_TYPE* definition is part of the mbox message and
it will be used by the other consumers of AF driver hence moving to mbox.h.
Also renamed FLOW_* definitions to NIX_FLOW_* to avoid global
name space collisions, as we have various coming from
include/uapi/linux/pkt_cls.h for example.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the time of initial broadcast packet replication table init,
NIXLFs are not yet attached to PF_FUNCs. Hence skipped checking
NIXLF while submitting MCE entry init instruction to NIX admin queue.
Also did a minor cleanup while installing bcast match entry in
packet parser unit i.e NPC.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn says:
====================
udp msg_zerocopy
Enable MSG_ZEROCOPY for udp sockets
Patch 1/3 is the main patch, a rework of RFC patch
http://patchwork.ozlabs.org/patch/899630/
more details in the patch commit message
Patch 2/3 is an optimization to remove a branch from the UDP hot path
and refcount_inc/refcount_dec_and_test pair when zerocopy is used.
This used to be included in the first patch in v2.
Patch 3/3 runs the already existing udp zerocopy tests
as part of kselftest
See also recent Linux Plumbers presentation
https://linuxplumbersconf.org/event/2/contributions/106/attachments/104/128/willemdebruijn-lpc2018-udpgso-presentation-20181113.pdf
Changes:
v1 -> v2
- Fixup reverse christmas tree violation
v2 -> v3
- Split refcount avoidance optimization into separate patch
- Fix refcount leak on error in fragmented case
(thanks to Paolo Abeni for pointing this one out!)
- Fix refcount inc on zero
v3 -> v4
- Move skb_zcopy_set below the only kfree_skb that might cause
a premature uarg destroy before skb_zerocopy_put_abort
- Move the entire skb_shinfo assignment block, to keep that
cacheline access in one place
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Both msg_zerocopy and udpgso_bench have udp zerocopy variants.
Exercise these as part of the standard kselftest run.
With udp, msg_zerocopy has no control channel. Ensure that the
receiver exits after the sender by accounting for the initial
delay in starting them (in msg_zerocopy.sh).
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With MSG_ZEROCOPY, each skb holds a reference to a struct ubuf_info.
Release of its last reference triggers a completion notification.
The TCP stack in tcp_sendmsg_locked holds an extra ref independent of
the skbs, because it can build, send and free skbs within its loop,
possibly reaching refcount zero and freeing the ubuf_info too soon.
The UDP stack currently also takes this extra ref, but does not need
it as all skbs are sent after return from __ip(6)_append_data.
Avoid the extra refcount_inc and refcount_dec_and_test, and generally
the sock_zerocopy_put in the common path, by passing the initial
reference to the first skb.
This approach is taken instead of initializing the refcount to 0, as
that would generate error "refcount_t: increment on 0" on the
next skb_zcopy_set.
Changes
v3 -> v4
- Move skb_zcopy_set below the only kfree_skb that might cause
a premature uarg destroy before skb_zerocopy_put_abort
- Move the entire skb_shinfo assignment block, to keep that
cacheline access in one place
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend zerocopy to udp sockets. Allow setting sockopt SO_ZEROCOPY and
interpret flag MSG_ZEROCOPY.
This patch was previously part of the zerocopy RFC patchsets. Zerocopy
is not effective at small MTU. With segmentation offload building
larger datagrams, the benefit of page flipping outweights the cost of
generating a completion notification.
tools/testing/selftests/net/msg_zerocopy.sh after applying follow-on
test patch and making skb_orphan_frags_rx same as skb_orphan_frags:
ipv4 udp -t 1
tx=191312 (11938 MB) txc=0 zc=n
rx=191312 (11938 MB)
ipv4 udp -z -t 1
tx=304507 (19002 MB) txc=304507 zc=y
rx=304507 (19002 MB)
ok
ipv6 udp -t 1
tx=174485 (10888 MB) txc=0 zc=n
rx=174485 (10888 MB)
ipv6 udp -z -t 1
tx=294801 (18396 MB) txc=294801 zc=y
rx=294801 (18396 MB)
ok
Changes
v1 -> v2
- Fixup reverse christmas tree violation
v2 -> v3
- Split refcount avoidance optimization into separate patch
- Fix refcount leak on error in fragmented case
(thanks to Paolo Abeni for pointing this one out!)
- Fix refcount inc on zero
- Test sock_flag SOCK_ZEROCOPY directly in __ip_append_data.
This is needed since commit 5cf4a8532c ("tcp: really ignore
MSG_ZEROCOPY if no SO_ZEROCOPY") did the same for tcp.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcATmGAAoJEG4XJFUm622bk9kH/1RWa2z7Gmjr2wBSLHryvRAH
3FAUSJ4GJPH6MJ5X824srkcVsx2Y1RVt2i+bLXRXLq35aZkrFswohTXVM2h5dU7T
Uy2SL+q9pBUcS7fyv9bE7XV7KsFBJly/5p/wciVRZMnEK6X/w6KkBx/vGvlm5I/C
q196KazbVAYcl6s7KMrfFOYt0Wsto/gdEeesSVBkmcCTEkiKUjjJ4WEDVvAKK+qB
AiwgSdioqYmmEiUuredm6bhVqZG3K2mScoCy95N3jXkiDaKkaYgVtBuAU4Cdju/t
WgLIc9EnUYxXZtwnt889X62P1OkDOtKlj/mjdsGyF0Vrs1W+kErDO0NocOvu2Tk=
=9bL7
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-11-30' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bartosz Golaszewski says:
====================
davinci_emac: read the MAC address from nvmem
This series is part of a bigger series that aims at removing the platform
data structure from the at24 EEPROM driver[1].
We provide a generalized version of of_get_nvmem_mac_address(), switch the
only user of the of_ variant to using it, remove the previous
implementation and use the new routine in the davinci_emac driver.
[1] https://lkml.org/lkml/2018/11/13/884
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
All DaVinci boards still supported in board files now define nvmem
cells containing the MAC address. We want to stop using the setup
callback from at24 so the MAC address for those users will no longer
be provided over platform data. If we didn't get a valid MAC in pdata,
try nvmem before resorting to a random MAC.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've switched all users to nvmem_get_mac_address(). Remove the now
dead code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now have a generalized helper routine to read the MAC address from
nvmem which takes struct device as argument. The nvmem subsystem will
then try device tree first before all other potential providers.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have of_get_nvmem_mac_address() but some non-DT systems want
to read the MAC address from NVMEM too. Implement a generalized routine
that takes struct device as argument.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some users of rhashtables might need to move an object from one table
to another - this appears to be the reason for the incomplete usage
of NULLS markers.
To support these, we store a unique NULLS_MARKER at the end of
each chain, and when a search fails to find a match, we check
if the NULLS marker found was the expected one. If not, the search
may not have examined all objects in the target bucket, so it is
repeated.
The unique NULLS_MARKER is derived from the address of the
head of the chain. As this cannot be derived at load-time the
static rhnull in rht_bucket_nested() needs to be initialised
at run time.
Any caller of a lookup function must still be prepared for the
possibility that the object returned is in a different table - it
might have been there for some time.
Note that this does NOT provide support for other uses of
NULLS_MARKERs such as allocating with SLAB_TYPESAFE_BY_RCU or changing
the key of an object and re-inserting it in the same table.
These could only be done safely if new objects were inserted
at the *start* of a hash chain, and that is not currently the case.
Signed-off-by: NeilBrown <neilb@suse.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Salil Mehta says:
====================
Adds VF/PF PCIe reg dump(ethtool -d) support to HNS3 driver
This patchset adds VF/PF PCIe register dump support to HNS3 VF and PF
driver using "ethtool -d" command.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to dump PF PCIe registers using ethtool -d
for HNS3 PF Driver.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn