This change just add the IBM eHEA 10Gb network drivers as supported.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5 GHz CTL indexes were not being read for all hardware
devices due to the masking out through the CTL_MODE_M mask
being one bit too short. Without this the calibrated regulatory
maximum values were not being picked up when devices operate
on 5 GHz in HT40 mode. The final output power used for Atheros
devices is the minimum between the calibrated CTL values and
what CRDA provides.
Cc: stable@kernel.org [2.6.27+]
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM is compressed on AR9003, upon decompression
the wrong upper limit was being used for the block which
prevented the 5 GHz CTL indexes from being used, which are
stored towards the end of the EEPROM block. This fix allows
the actual intended regulatory limits to be used on AR9003
hardware.
Cc: stable@kernel.org [2.6.36+]
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once we started enforcing the a nl_table[] entry exist for
a protocol, NETLINK_USERSOCK stopped working. Add a dummy
table entry so that it works again.
Reported-by: Thomas Voegtle <tv@lio96.de>
Tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If irda_open_tsap() fails, the irda_bind() code tries to destroy
the ->ias_obj object by hand, but does so wrongly.
In particular, it fails to a) release the hashbin attached to the
object and b) reset the self->ias_obj pointer to NULL.
Fix both problems by using irias_delete_object() and explicitly
setting self->ias_obj to NULL, just as irda_release() does.
Reported-by: Tavis Ormandy <taviso@cmpxchg8b.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wireless extensions have an unfortunate, undocumented
requirement which requires drivers to always fill
iwp->length when returning a successful status. When
a driver doesn't do this, it leads to a kernel heap
content leak when userspace offers a larger buffer
than would have been necessary.
Arguably, this is a driver bug, as it should, if it
returns 0, fill iwp->length, even if it separately
indicated that the buffer contents was not valid.
However, we can also at least avoid the memory content
leak if the driver doesn't do this by setting the iwp
length to max_tokens, which then reflects how big the
buffer is that the driver may fill, regardless of how
big the userspace buffer is.
To illustrate the point, this patch also fixes a
corresponding cfg80211 bug (since this requirement
isn't documented nor was ever pointed out by anyone
during code review, I don't trust all drivers nor
all cfg80211 handlers to implement it correctly).
Cc: stable@kernel.org [all the way back]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new workqueue changes helped me find this bug
that's been lingering since the changes to the work
processing in mac80211 -- the work timer is never
deleted properly. Do that to avoid having it fire
after all data structures have been freed. It can't
be re-armed because all it will do, if running, is
schedule the work, but that gets flushed later and
won't have anything to do since all work items are
gone by now (by way of interface removal).
Cc: stable@kernel.org [2.6.34+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael reported that p54* never really entered power
save mode, even tough it was enabled.
It turned out that upon a power save mode change the
firmware will set a special flag onto the last outgoing
frame tx status (which in this case is almost always the
designated PSM nullfunc frame). This flag confused the
driver; It erroneously reported transmission failures
to the stack, which then generated the next nullfunc.
and so on...
Cc: <stable@kernel.org>
Reported-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This avoids a NULL pointer dereference as reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=625889
When the WARN condition is hit in ieee80211_get_tx_rate, it will return
NULL. So, we need to check the return value and avoid dereferencing it
in that case.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org
Acked-by: Bob Copeland <me@bobcopeland.com>
pcnet_cs:
add new_id: "KENTRONICS KEP-230" 10Base-T PCMCIA card.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The string clone is only used as a temporary copy of the argument val
within the while loop, and so it should be freed before leaving the
function. The call to strsep, however, modifies clone, so a pointer to the
front of the string is kept in saved_clone, to make it possible to free it.
The sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression x;
expression E;
identifier l;
statement S;
@@
*x= \(kasprintf\|kstrdup\)(...);
...
if (x == NULL) S
... when != kfree(x)
when != E = x
if (...) {
<... when != kfree(x)
* goto l;
...>
* return ...;
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 886275ce41 (param: lock
if_sdio's lbs_helper_name and lbs_fw_name against sysfs changes)
introduced new fields into the if_sdio_card structure. It caused
missalignment of the if_sdio_card.buffer field and failure at driver
load time:
~# modprobe libertas_sdio
[ 62.315124] libertas_sdio: Libertas SDIO driver
[ 62.319976] libertas_sdio: Copyright Pierre Ossman
[ 63.020629] DMA misaligned error with device 48
[ 63.025207] mmci-omap-hs mmci-omap-hs.1: unexpected dma status 800
[ 66.005035] libertas: command 0x0003 timed out
[ 66.009826] libertas: Timeout submitting command 0x0003
[ 66.016296] libertas: PREP_CMD: command 0x0003 failed: -110
Adding explicit alignment attribute for the if_sdio_card.buffer field
fixes this problem.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
caif does not build on ia64 starting with 2.6.32-rc1. Using
asm/unaligned.h instead of linux/unaligned/le_byteshift.h fixes the issue.
include/linux/unaligned/le_byteshift.h:40:50: error: redefinition of 'get_unaligned_le16'
include/linux/unaligned/le_byteshift.h:45:50: error: redefinition of 'get_unaligned_le32'
include/linux/unaligned/le_byteshift.h:50:50: error: redefinition of 'get_unaligned_le64'
include/linux/unaligned/le_byteshift.h:55:51: error: redefinition of 'put_unaligned_le16'
include/linux/unaligned/le_byteshift.h:60:51: error: redefinition of 'put_unaligned_le32'
include/linux/unaligned/le_byteshift.h:65:51: error: redefinition of 'put_unaligned_le64'
include/linux/unaligned/le_struct.h:31:51: note: previous definition of 'put_unaligned_le64' was here
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves a missplaced sock_put(sk) after
bh_unlock_sock(sk)
like in other parts of AX25 driver.
Signed-off-by: Bernard Pidoux <f6bvp@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Qlge is freeing the buffers before stopping the card DMA, and
this can cause some severe error, as a EEH event on PPC.
This patch just stop the card and then free the resources.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
close https://bugzilla.kernel.org/show_bug.cgi?id=16529
Before calling dev_forward_skb(), we should make sure skb head contains
at least an ethernet header, even if length included in upper layer said
so. Use pskb_may_pull() to make sure this ethernet header is present in
skb head.
Reported-by: Thomas Heil <heil@terminal-consulting.de>
Reported-by: Ian Campbell <Ian.Campbell@eu.citrix.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue come from ruby language community. Below test program
hang up when only run on Linux.
% uname -mrsv
Linux 2.6.26-2-486 #1 Sat Dec 26 08:37:39 UTC 2009 i686
% ruby -rsocket -ve '
BasicSocket.do_not_reverse_lookup = true
serv = TCPServer.open("127.0.0.1", 0)
s1 = TCPSocket.open("127.0.0.1", serv.addr[1])
s2 = serv.accept
s2.close
s1.write("a") rescue p $!
s1.write("a") rescue p $!
Thread.new {
s1.write("a")
}.join'
ruby 1.9.3dev (2010-07-06 trunk 28554) [i686-linux]
#<Errno::EPIPE: Broken pipe>
[Hang Here]
FreeBSD, Solaris, Mac doesn't. because Ruby's write() method call
select() internally. and tcp_poll has a bug.
SUS defined 'ready for writing' of select() as following.
| A descriptor shall be considered ready for writing when a call to an output
| function with O_NONBLOCK clear would not block, whether or not the function
| would transfer data successfully.
That said, EPIPE situation is clearly one of 'ready for writing'.
We don't have read-side issue because tcp_poll() already has read side
shutdown care.
| if (sk->sk_shutdown & RCV_SHUTDOWN)
| mask |= POLLIN | POLLRDNORM | POLLRDHUP;
So, Let's insert same logic in write side.
- reference url
http://blade.nagaokaut.ac.jp/cgi-bin/scat.rb/ruby/ruby-core/31065http://blade.nagaokaut.ac.jp/cgi-bin/scat.rb/ruby/ruby-core/31068
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As discovered by Anton Blanchard, current code to autotune
tcp_death_row.sysctl_max_tw_buckets, sysctl_tcp_max_orphans and
sysctl_max_syn_backlog makes little sense.
The bigger a page is, the less tcp_max_orphans is : 4096 on a 512GB
machine in Anton's case.
(tcp_hashinfo.bhash_size * sizeof(struct inet_bind_hashbucket))
is much bigger if spinlock debugging is on. Its wrong to select bigger
limits in this case (where kernel structures are also bigger)
bhash_size max is 65536, and we get this value even for small machines.
A better ground is to use size of ehash table, this also makes code
shorter and more obvious.
Based on a patch from Anton, and another from David.
Reported-and-tested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Anton Blanchard when we use
percpu_counter_read_positive() to make our orphan socket limit checks,
the check can be off by up to num_cpus_online() * batch (which is 32
by default) which on a 128 cpu machine can be as large as the default
orphan limit itself.
Fix this by doing the full expensive sum check if the optimized check
triggers.
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Casting "pep->tx_desc_dma" to to a struct tx_desc pointer makes gcc
complain:
drivers/net/pxa168_eth.c:657: warning:
cast to pointer from integer of different size
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_mii_ioctl() function changed recently. It now takes a struct
ifreq pointer directly.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple issues here:
* Some resources weren't released.
* If alloc_etherdev() failed it would have caused a NULL dereference
because "pep" would be null when we checked "if (pep->clk)".
* Also it's better to propagate the error codes from mdiobus_register()
instead of just returning -ENOMEM.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"pep->pd" isn't checked consistently in this function. For example it's
dereferenced unconditionally on the next line after the end of the if
condition. This function is only called from pxa168_eth_probe() and
pep->pd is always non-NULL so I removed the check.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that phylib will call adjust_link before returning
from {,of_}phy_connect(), which may cause the following [very rare,
though] oops upon reopening the device:
Unable to handle kernel paging request for data at address 0x0000024c
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT SMP NR_CPUS=2 LTT NESTING LEVEL : 0
P1021 RDB
Modules linked in:
NIP: c0345dac LR: c0345dac CTR: c0345d84
TASK = dffab6b0[30] 'events/0' THREAD: c0d24000 CPU: 0
[...]
NIP [c0345dac] adjust_link+0x28/0x19c
LR [c0345dac] adjust_link+0x28/0x19c
Call Trace:
[c0d25f00] [000045e1] 0x45e1 (unreliable)
[c0d25f30] [c036c158] phy_state_machine+0x3ac/0x554
[...]
Here is why. Drivers store phydev in their private structures, e.g.
gianfar driver:
static int init_phy(struct net_device *dev)
{
...
priv->phydev = of_phy_connect(...);
...
}
So that adjust_link could retrieve it back:
static void adjust_link(struct net_device *dev)
{
...
struct phy_device *phydev = priv->phydev;
...
}
If the device has been opened before, then phydev->state is set to
PHY_HALTED (or undefined if the driver didn't call phy_stop()).
Now, phy_connect starts the PHY state machine before returning phydev to
the driver:
phy_start_machine(phydev, NULL);
if (phydev->irq > 0)
phy_start_interrupts(phydev);
return phydev;
The time between 'phy_start_machine()' and 'return phydev' is undefined.
The start machine routine delays execution for 1 second, which is enough
for most cases. But under heavy load, or if you're unlucky, it is quite
possible that PHY state machine will execute before phy_connect()
returns, and so adjust_link callback will try to dereference phydev,
which is not yet ready.
To fix the issue, simply initialize the PHY's state to PHY_READY during
phy_attach(). This will ensure that phylib won't call adjust_link before
phy_start().
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this error on an s390 allyesconfig build:
linux-2.6/drivers/net/caif/caif_spi.c:98:
undefined reference to `dma_free_coherent'
Cc: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If netconsole is in use, there is a possibility for deadlock in 3c59x between
boomerang_interrupt and boomerang_start_xmit. Both routines take the vp->lock,
and if netconsole is in use, a pr_* call from the boomerang_interrupt routine
will result in the netconsole code attempting to trnasmit an skb, which can try
to take the same spin lock, resulting in deadlock.
The fix is pretty straightforward. This patch allocats a bit in the 3c59x
private structure to indicate that its handling an interrupt. If we get into
the transmit routine and that bit is set, we can be sure that we have recursed
and will deadlock if we continue, so instead we just return NETDEV_TX_BUSY, so
the stack requeues the skb to try again later.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function qlcnic_intr has pointer to qlcnic_host_sds_ring
as second parameter not pointer to qlcnic_adapter.
Signed-off-by: Yinglin Luan <synmyth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function netxen_intr has pointer to nx_host_sds_ring
as second parameter not pointer to netxen_adapter.
Signed-off-by: Yinglin Luan <synmyth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nf_bridge_alloc() always reset the skb->nf_bridge, so we should always
put the old one.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit f3c5c1bfd4
(netfilter: xtables: make ip_tables reentrant) forgot to
also compute the jumpstack size in the compat handlers.
Result is that "iptables -I INPUT -j userchain" turns into -j DROP.
Reported by Sebastian Roesner on #netfilter, closes
http://bugzilla.netfilter.org/show_bug.cgi?id=669.
Note: arptables change is compile-tested only.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
__packed is only defined in kernel space, so we should use
__attribute__((packed)) for the code shared between kernel and user space.
Two __attribute() annotations are replaced with __attribute__() too.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Bruce Allan <bruce.w.allan@intel.com>
The alternate MAC address feature is only supported by 80003ES2LAN and
82571 LOMs as well as a couple 82571 mezzanine cards. Checking for an
alternate MAC address on other parts can fail leading to the driver not
able to load. This patch limits the check for an alternate MAC address
to be done only for parts that support the feature.
This issue has been around since support for the feature was introduced
to the e1000e driver in 2.6.34.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Reported-by: Fabio Varesano <fax8@users.sourceforge.net>
Cc: stable@kernel.org
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the e1000-devel mailing list, Nils Faerber reported latency issues with
the 82573 LOM on a ThinkPad X60. It was found to be caused by ASPM L1;
disabling it resolves the latency. The issue is present in kernels back
to 2.6.34 and possibly 2.6.33.
Reported-by: Nils Faerber <nils.faerber@kernelconcepts.de>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions ll_temac_rx_irq and ll_temac_tx_irq
have pointer to net_device as second parameter not
pointer to temac_local.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dont clear netdev->stats, it might give transient wrong values to
concurrent stat readers.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dont clear netdev->stats, it might give transient wrong values to
concurrent stat readers.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After skb is queued, its illegal to dereference it.
Cache skb->len into a temporary variable.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spin lock rds_ring->lock is used in poll routine, so other users should
use spin_lock_bh(). While posting rx buffers from netxen_nic_attach,
rds_ring->lock is not required, so cleaning it instead of fixing it by
spin_lock_bh().
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding a new vlan, if the underlying interface has no carrier,
then the newly added vlan interface should also have no carrier.
At present, this is not true - the newly added vlan is added with
carrier up. Fix by checking state of real device.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ehea: Fix synchronization between HW and SW send queue
When memory is added to / removed from a partition via the Memory DLPAR
mechanism, the eHEA driver has to do a couple of things to reflect the
memory change in its own IO address translation tables. This involves
stopping and restarting the HW queues.
During this operation, it is possible that HW and SW pointer into these
queues get out of sync. This results in a situation where packets that
are attached to a send queue are not transmitted immediately, but
delayed until further X packets have been put on the queue.
This patch detects such loss of synchronization, and resets the ehea
port when needed.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bnx2x version to 1.52.53-4
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY locking is required between two ports for some external PHYs. Since
initialization was done in the common init function (called only on the
first port initialization) rather than in the port init function, there
was in fact no PHY locking between the ports.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Breno Leitao