Add function v4l2_fwnode_reference_parse() for parsing them as async
sub-devices. This can be done on e.g. flash or lens async sub-devices that
are not part of but are associated with a sensor.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In V4L2 the practice is to have the KernelDoc documentation in the header
and not in .c source code files. This consequently makes the V4L2 fwnode
function documentation part of the Media documentation build.
Also correct the link related function and argument naming in
documentation and add an asterisk to v4l2_fwnode_endpoint_free()
documentation to make it proper KernelDoc documentation.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While registering a notifier, check that each newly added fwnode is
unique, and return an error if it is not. Also check that a newly added
notifier does not have the same fwnodes twice.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Registering a notifier has required the knowledge of struct v4l2_device
for the reason that sub-devices generally are registered to the
v4l2_device (as well as the media device, also available through
v4l2_device).
This information is not available for sub-device drivers at probe time.
What this patch does is that it allows registering notifiers without
having v4l2_device around. Instead the sub-device pointer is stored in the
notifier. Once the sub-device of the driver that registered the notifier
is registered, the notifier will gain the knowledge of the v4l2_device,
and the binding of async sub-devices from the sub-device driver's notifier
may proceed.
The complete callback of the root notifier will be called only when the
v4l2_device is available and no notifier has pending sub-devices to bind.
No complete callbacks are supported for sub-device notifiers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Refactor the V4L2 async framework a little in preparation for async
sub-device notifiers. This avoids making some structural changes in the
patch actually implementing sub-device notifiers, making that patch easier
to review.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The information on how many async sub-devices would be bindable to a
notifier is typically dependent on information from platform firmware and
it's not driver's business to be aware of that.
Many V4L2 main drivers are perfectly usable (and useful) without async
sub-devices and so if there aren't any around, just proceed call the
notifier's complete callback immediately without registering the notifier
itself.
If a driver needs to check whether there are async sub-devices available,
it can be done by inspecting the notifier's num_subdevs field which tells
the number of async sub-devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Register the sub-device before calling the notifier's bound callback.
Doing this the other way around is problematic as the struct v4l2_device
has not assigned for the sub-device yet and may be required by the bound
callback.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add three helper functions to call async operations callbacks. Besides
simplifying callbacks, this allows async notifiers to have no ops set,
i.e. it can be left NULL.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The async subdev notifier .bound(), .unbind() and .complete() operations
are function pointers stored directly in the v4l2_async_subdev
structure. As the structure isn't immutable, this creates a potential
security risk as the function pointers are mutable.
To fix this, move the function pointers to a new
v4l2_async_subdev_operations structure that can be made const in
drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If no source pads are found in an entity, print the name of the entity.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We only want to link sub-devices that were bound to the async notifier the
isp driver registered but there may be other sub-devices in the
v4l2_device as well. Check for the correct async notifier.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of using a custom driver implementation, use
v4l2_async_notifier_parse_fwnode_endpoints() to parse the fwnode endpoints
of the device.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of using a custom driver implementation, use
v4l2_async_notifier_parse_fwnode_endpoints() to parse the fwnode endpoints
of the device.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add two functions for parsing devices graph endpoints:
v4l2_async_notifier_parse_fwnode_endpoints and
v4l2_async_notifier_parse_fwnode_endpoints_by_port. The former iterates
over all endpoints whereas the latter only iterates over the endpoints in
a given port.
The former is mostly useful for existing drivers that currently implement
the iteration over all the endpoints themselves whereas the latter is
especially intended for devices with both sinks and sources: async
sub-devices for external devices connected to the device's sources will
have already been set up, or the external sub-devices are part of the
master device.
Depends-on: ("device property: preserve usecount for node passed to of_fwnode_graph_get_port_parent()")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Rename internal functions to make the names of the functions better
describe what they do.
Old name New name
v4l2_async_test_notify v4l2_async_match_notify
v4l2_async_belongs v4l2_async_find_match
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The check whether an async sub-device is bound to a notifier was performed
without list_lock held, making it possible for another process to
unbind the async sub-device before the sub-device unregistration function
proceeds to take the lock.
Fix this by first acquiring the lock and then proceeding with the check.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The notifier complete callback may return an error. This error code was
simply returned to the caller but never handled properly.
Move calling the complete callback function to the caller from
v4l2_async_test_notify and undo the work that was done either in async
sub-device or async notifier registration.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The call to v4l2_async_cleanup() will set sd->asd to NULL so passing it to
notifier->unbind() has no effect and leaves the notifier confused. Call
the unbind() callback prior to cleaning up the subdevice to avoid this.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_async_cleanup() is called when the async sub-device is unbound from
the media device. As the pointer is set by the driver registering the
async sub-device, leave the pointer as set by the driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove V4L2 async re-probing support. The re-probing support has been
there to support cases where the sub-devices require resources provided by
the main driver's hardware to function, such as clocks.
Reprobing has allowed unbinding and again binding the main driver without
explicitly unbinding the sub-device drivers. This is certainly not a
common need, and the responsibility will be the user's going forward.
An alternative could have been to introduce notifier specific locks.
Considering the complexity of the re-probing and that it isn't really a
solution to a problem but a workaround, remove re-probing instead.
If there is a need to support the clock provider unregister/register cycle
while keeping the clock references in the consumers in the future, this
should be implemented in the clock framework instead, not in V4L2.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The test_pattern_menu[] array has two valid items and a null terminated
item. So the control's maximum value which is passed to
v4l2_ctrl_new_std_menu_items() should be one. However,
'ARRAY_SIZE(test_pattern_menu) - 1' is actually passed and it's not
correct.
Fix it by removing unnecessary terminated entry and let the correct
control's maximum value be passed to v4l2_ctrl_new_std_menu_items().
Cc: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_i2c_subdev_init() sets V4L2_SUBDEV_FL_IS_I2C flag in the
subdev->flags. But this driver overwrites subdev->flags immediately after
calling v4l2_i2c_subdev_init(). So V4L2_SUBDEV_FL_IS_I2C is not set after
all.
This stops breaking subdev->flags and preserves V4L2_SUBDEV_FL_IS_I2C.
Side note: According to the comment in v4l2_device_unregister(), this is
problematic only if the device is platform bus device. Device tree or
ACPI based devices are not affected.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_i2c_subdev_init() sets V4L2_SUBDEV_FL_IS_I2C flag in the
subdev->flags. But this driver overwrites subdev->flags immediately after
calling v4l2_i2c_subdev_init(). So V4L2_SUBDEV_FL_IS_I2C is not set after
all.
This stops breaking subdev->flags and preserves V4L2_SUBDEV_FL_IS_I2C.
Side note: According to the comment in v4l2_device_unregister(), this is
problematic only if the device is platform bus device. Device tree or
ACPI based devices are not affected.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_i2c_subdev_init() sets V4L2_SUBDEV_FL_IS_I2C flag in the
subdev->flags. But this driver overwrites subdev->flags immediately after
calling v4l2_i2c_subdev_init(). So V4L2_SUBDEV_FL_IS_I2C is not set after
all.
This stops breaking subdev->flags and preserves V4L2_SUBDEV_FL_IS_I2C.
Side note: According to the comment in v4l2_device_unregister(), this is
problematic only if the device is platform bus device. Device tree or
ACPI based devices are not affected.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_i2c_subdev_init() sets V4L2_SUBDEV_FL_IS_I2C flag in the
subdev->flags. But this driver overwrites subdev->flags immediately after
calling v4l2_i2c_subdev_init(). So V4L2_SUBDEV_FL_IS_I2C is not set after
all.
This stops breaking subdev->flags and preserves V4L2_SUBDEV_FL_IS_I2C.
Side note: According to the comment in v4l2_device_unregister(), this is
problematic only if the device is platform bus device. Device tree or
ACPI based devices are not affected.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Make use of the swap macro and remove unnecessary variable tmp_frame.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix the clock ID to do the runtime pm should be ISC_ISPCK,
instead of ISC_MCK in clk_prepare(), clk_unprepare() and
isc_clk_is_enabled().
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pointer pix is being initialized to a value and a little later
being assigned the same value again. Remove the initial assignment to
avoid a duplicate assignment. Cleans up the clang warning:
drivers/media/platform/sti/bdisp/bdisp-v4l2.c:726:26: warning: Value
stored to 'pix' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Variable j is being set to zero before a loop and also
immediately inside the loop and is not used after the loop.
Hence the first assignment is redundant and can be removed.
Cleans up clang warning:
drivers/media/usb/gspca/gspca.c:1078:2: warning: Value stored
to 'j' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Variable index is set to zero and then set to zero again
a few lines later in a for loop initialization. Remove the
redundant setting of index to zero. Cleans up the clang
warning:
drivers/media/usb/dvb-usb-v2/mxl111sf-i2c.c:519:3: warning: Value
stored to 'index' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Variable freq is initialized to f->frequency however this value
is never read and freq is later updated; hence the initialization
is redundant and can be removed.
Cleans up clang warning:
drivers/media/radio/radio-raremono.c:257:6: warning: Value stored
to 'freq' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Because the brightness and contrast controls share a register,
usbtv_s_ctrl needs to read the existing values for both controls before
inserting the new value. However, the code accidentally wrote to the
registers (from an uninitialised stack array), rather than reading them.
The user-visible effect of this was that adjusting the brightness would
also set the contrast to a random value, and vice versa -- so it wasn't
possible to correctly adjust the brightness of usbtv's video output.
Tested with an "EasyDAY" UTV007 device.
Fixes: c53a846c48 ("usbtv: add video controls")
Signed-off-by: Adam Sampson <ats@offog.org>
Reviewed-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Bhumika Goyal <bhumirks@gmail.com>
Cc: Mike Isely <isely@pobox.com>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Sergey Kozlov <serjk@netup.ru>
Cc: Abylay Ospan <aospan@netup.ru>
Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Geliang Tang <geliangtang@gmail.com>
Cc: Sean Young <sean@mess.org>
Cc: "Pali Rohár" <pali.rohar@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
[hans.verkuil@cisco.com: dropped pci/ttpci/av7110_ir.c patch chunk]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The probe() cleanup code ('goto foo_error') was very messy. It appears
that this code wasn't updated when I switched to the devm_ functions
in an earlier version.
Update the code to use 'return error' where it can and do proper cleanup
where it needs to.
Note that the original code wasn't buggy, it was just messy.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
usb_endpoint_maxp() has an inline keyword and searches for bits[10:0]
by & operation with 0x7ff. So, we can remove the duplicate & operation
with 0x7ff.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The newly added driver has incorrect #ifdef annotations on its
PM functions, leading to a harmless compile-time warning when
CONFIG_PM is disabled:
drivers/media/platform/rockchip/rga/rga.c:760:13: error: 'rga_disable_clocks' defined but not used [-Werror=unused-function]
static void rga_disable_clocks(struct rockchip_rga *rga)
^~~~~~~~~~~~~~~~~~
drivers/media/platform/rockchip/rga/rga.c:728:12: error: 'rga_enable_clocks' defined but not used [-Werror=unused-function]
This removes the #ifdef and marks the functions as __maybe_unused,
so gcc can silently drop all the unused code.
Fixes: f7e7b48e6d ("[media] rockchip/rga: v4l2 m2m support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
cec_allocate_adapter never returns NULL, so just use IS_ERR instead of
PTR_ERR_OR_ZERO.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
VIDIOC_DQEVENT and VIDIOC_QUERY_EXT_CTRL should give the same output for
the control flags field.
This patch creates a new function user_flags(), that calculates the user
exported flags value (which is different than the kernel internal flags
structure). This function is then used by all the code that exports the
internal flags to userspace.
Reported-by: Dimitrios Katsaros <patcherwork@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v3.17 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these structures const as they are only getting passed to the
functions vpfe_{register/unregister}_ccdc_device having the argument as
const.
Structures found using Coccinelle and changes done by hand.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make the function arguments of functions vpfe_{register/unregister}_ccdc_device
const as the pointer dev does not modify the fields of the structure
it points to. Also, declare the variable ccdc_dev const as it points to the
same structure as dev but it does not modify the fields as well.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: devendra sharma <devendra.sharma9091@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. This requires adding a pointer to
hold the timer's target file, as there won't be a way to pass this in the
future.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it is only used in a copy operation in the files
referencing it. Add const to declaration in the header too.
Structure found using Coccienlle and changes done by hand.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it is only passed to the const argument of the
function videobuf_queue_vmalloc_init in the file referencing it.
Also, make the declaration in the header const.
Structure found using Coccienlle and changes done by hand.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move a debug message so that a null pointer access can not happen
for the variable "vout" in this function.
Fixes: 5c7ab6348e ("V4L/DVB: V4L2: Add support for OMAP2/3 V4L2 display driver on top of DSS2")
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Astrometa T2hybrid (15f4:0135) has IR on Interface 0.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the keymap module for Astrometa T2hybrid remote control commands.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Evromedia USB Full Hybrid Full HD (1b80:d3b2) has IR on Interface 0.
Remote controller supplied with this tuner fully compatible
with RC_MAP_MSI_DIGIVOX_III.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: "Antti Seppälä" <a.seppala@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: "David Härdeman" <david@hardeman.nu>
Cc: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drivers/media/platform/atmel/atmel-isc.c: In function 'isc_async_complete':
drivers/media/platform/atmel/atmel-isc.c:1900:28: warning: variable 'sd_entity' set but not used [-Wunused-but-set-variable]
struct isc_subdev_entity *sd_entity;
^~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is a NEC protocol type remote controller distributed with
96boards poplar@tocoding board.
Signed-off-by: Younian Wang <wangyounian@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is a NEC protocol type remote controller distributed with
hisilicon TV demo boards.
Signed-off-by: Younian Wang <wangyounian@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It seems that the return value of usb_ifnum_to_if() can be NULL and
needs to be checked.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The TC358743 does not support more than 4 data lanes. Check that the
lane count is valid.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When I was supporting Rpi Camera Module on the ASUS Tinker board,
I found this driver have some issues with rockchip's mipi-csi driver.
It didn't place clock lane in LP-11 state before performing
D-PHY initialisation.
>From our experience, on some OV sensors,
LP-11 state is not achieved while BIT(5)-0x4800 is cleared.
So let's set BIT(5) and BIT(0) both while not streaming, in order to
coax the clock lane into LP-11 state.
0x4800 : MIPI CTRL 00
BIT(5) : clock lane gate enable
0: continuous
1: none-continuous
BIT(0) : manually set clock lane
0: Not used
1: used
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Reviewed-by: Luis Oliveira <lolivei@synopsys.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the ov7670_s_power function which is responsible for
manipulating the power dowm mode through the PWDN pin and the reset
operation through the RESET pin, and keep it powered at all times.
[sakari.ailus@linux.intel.com: set pwdn_gpio direction only once]
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the get_fmt callback, also enable V4L2_SUBDEV_FL_HAS_DEVNODE flag
to make this subdev has device node.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the media entity pads initialization.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver adds support for the Tegra CEC IP. It is based on the
NVIDIA drivers/misc/tegra-cec driver in their 3.10 kernel.
This has been converted to the CEC framework and cleaned up.
Tested with my Jetson TK1 board. It has also been tested with the
Tegra X1 in an embedded product.
Note of warning for the Tegra X2: this SoC supports two HDMI outputs,
but only one CEC adapter and the CEC bus is shared between the
two outputs. This is a design mistake and the CEC adapter can
control only one HDMI output. Never hook up both HDMI outputs
to the CEC bus in a hardware design: this is illegal as per the
CEC specification.
The CEC bus can be shared between multiple inputs and zero or one
outputs, but not between multiple outputs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The imx274 is a Sony CMOS image sensor that has 1/2.5 image size.
It supports up to 3840x2160 (4K) 60fps, 1080p 120fps. The interface
is 4-lane MIPI CSI-2 running at 1.44Gbps each.
This driver has been tested on Xilinx ZCU102 platform with a Leopard
LI-IMX274MIPI-FMC camera board.
Support for the following features:
-Resolutions: 3840x2160, 1920x1080, 1280x720
-Frame rate: 3840x2160 : 5 – 60fps
1920x1080 : 5 – 120fps
1280x720 : 5 – 120fps
-Exposure time: 16 – (frame interval) micro-seconds
-Gain: 1x - 180x
-VFLIP: enable/disabledrivers/media/i2c/imx274.c
-Test pattern: 12 test patterns
Signed-off-by: Leon Luo <leonl@leopardimaging.com>
Tested-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The TC358743 is an HDMI to MIPI CSI2-2 bridge.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We can remove the check for if "state->cec_adap" is NULL. The
cec_allocate_adapter() function never returns NULL and also we verified
that "state->cec_adap" is an error pointer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make vb2_ops const as they are only stored in the const field of a
vb2_queue structure. Make the declarations const too.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make vb2_ops const as they are only stored in the const field of a
vb2_queue structure. Make the declarations const too.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make this const as it is only used in a copy operation in the file
referencing it. Make the declaration const too.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make this const as it is only passed to the const argument of the
function videobuf_queue_sg_init in the file referencing it.
Also, make the declaration in the header const.
Structure found using Coccinelle and changes done by hand.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
kasprintf() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It should be "LP-11".
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- Delete seven error messages for a failed memory allocation
- Adjust seven checks for null pointers
- Use common error handling code in tm6000_usb_probe()
- Adjust jump targets so that the function "kfree" will be always called
with a non-null pointer.
- Delete an initialisation for the local variable "dev"
which became unnecessary with this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The kAPI cec-pin.h header also defined data structures that did
not belong here but were private to the CEC core code.
Split that part off into a cec-pin-priv.h header.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This addresses the wrong behavior of decoder stop command by
rewriting it. These new implementation enqueue an empty buffer
on the decoder input buffer queue to signal end-of-stream. The
client should stop queuing buffers on the V4L2 Output queue
and continue queuing/dequeuing buffers on Capture queue. This
process will continue until the client receives a buffer with
V4L2_BUF_FLAG_LAST flag raised, which means that this is last
decoded buffer with data.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.13 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In case of error, the function platform_device_register_data() returns
ERR_PTR() and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This fixes wrongly filled bytesused field of v4l2_plane structure
by include data_offset in the plane, Also fill data_offset and
bytesused for capture type of buffers only.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.13 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
To improve the readability of code, split the format array into two,
one for the format description, other for the register configuration.
Meanwhile, add the flag member to indicate the format can be achieved
from the sensor or be produced by the controller, and rename members
related to the register configuration.
Also add more formats support: GREY, ARGB444, ARGB555 and ARGB32.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove the memeber *config from the isc_subdev_entity struct,
the member is useless afterward.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
To meet the relationship, enable the HCLOCK and ispck during the
device probe, "isc_pck frequency is less than or equal to isc_ispck,
and isc_ispck is greater than or equal to HCLOCK."
Meanwhile, call the pm_runtime_enable() in the right place.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A software write operation to the ISC_CLKEN or ISC_CLKDIS register
requires double clock domain synchronization and is not permitted
when the ISC_SR.SIP is asserted. So add the .prepare and .unprepare
ops to make sure the ISC_CLKSR.SIP is unasserted before the write
operation to the ISC_CLKEN or ISC_CLKDIS register.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the spin lock for the clock enable and disable operations.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't currently harmful.
However, for some features it is necessary to instrument reads and
writes separately, which is not possible with ACCESS_ONCE(). This
distinction is critical to correct operation.
It's possible to transform the bulk of kernel code using the Coccinelle
script below. However, this doesn't handle comments, leaving references
to ACCESS_ONCE() instances which have been removed. As a preparatory
step, this patch converts the DVB ringbuffer code and comments to use
{READ,WRITE}_ONCE() consistently.
----
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-6-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This change will fix an issue with dma_free size found with
DMA API debug enabled.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.13 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of relying on a mix of runtime PM and the s_power() callback, drop
the s_power() callback altogether and use runtime PM solely.
As device access is required during device power-on and power-off
sequences, runtime PM alone cannot tell whether the device is available.
Thus the "active" field is introduced in struct smiapp_sensor to tell
whether it is safe to write to the device.
Consequently there is no need to power on the device whenever a file
handle is open. This functionality is removed as well. The user may still
control the device power management through sysfs. Autosuspend remains
enabled, with 1 s delay.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use unlocked __v4l2_ctrl_handler_setup() in order to make the
control setup atomic.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* commit '3728e6a255b5': (904 commits)
Linux 4.14-rc5
x86/microcode: Do the family check first
locking/lockdep: Disable cross-release features for now
x86/mm: Flush more aggressively in lazy TLB mode
mm, swap: use page-cluster as max window of VMA based swap readahead
mm: page_vma_mapped: ensure pmd is loaded with READ_ONCE outside of lock
kmemleak: clear stale pointers from task stacks
fs/binfmt_misc.c: node could be NULL when evicting inode
fs/mpage.c: fix mpage_writepage() for pages with buffers
linux/kernel.h: add/correct kernel-doc notation
tty: fall back to N_NULL if switching to N_TTY fails during hangup
Revert "vmalloc: back off when the current task is killed"
mm/cma.c: take __GFP_NOWARN into account in cma_alloc()
scripts/kallsyms.c: ignore symbol type 'n'
userfaultfd: selftest: exercise -EEXIST only in background transfer
mm: only display online cpus of the numa node
mm: remove unnecessary WARN_ONCE in page_vma_mapped_walk().
mm/mempolicy: fix NUMA_INTERLEAVE_HIT counter
include/linux/of.h: provide of_n_{addr,size}_cells wrappers for !CONFIG_OF
mm/madvise.c: add description for MADV_WIPEONFORK and MADV_KEEPONFORK
...
-----BEGIN PGP SIGNATURE-----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=VOJs
-----END PGP SIGNATURE-----
Merge tag 'media/v4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Core fixes:
- cec: Respond to unregistered initiators, when applicable
- dvb_frontend: only use kref after initialized
Driver-specific fixes:
- qcom, camss: Make function vfe_set_selection static
- qcom: VIDEO_QCOM_CAMSS should depend on HAS_DMA
- s5p-cec: add NACK detection support
- media: staging/imx: Fix uninitialized variable warning
- dib3000mc: i2c transfers over usb cannot be done from stack
- venus: init registered list on streamoff"
* tag 'media/v4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: dvb_frontend: only use kref after initialized
media: platform: VIDEO_QCOM_CAMSS should depend on HAS_DMA
media: cec: Respond to unregistered initiators, when applicable
media: s5p-cec: add NACK detection support
media: staging/imx: Fix uninitialized variable warning
media: qcom: camss: Make function vfe_set_selection static
media: venus: init registered list on streamoff
media: dvb: i2c transfers over usb cannot be done from stack
The script “checkpatch.pl” pointed information out like the following.
Comparison to NULL could be written...
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Omit an extra message for a memory allocation failure in s5p_mfc_probe()
function. This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The hardware rotation limits of gsc depends on SOC (Exynos
5250/5420/5433). Distinguish them and add them to the driver data.
[s.nawrocki@samsung.com: corrected num_entities in 5420 variant data]
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rockchip RGA is a separate 2D raster graphic acceleration unit. It
accelerates 2D graphics operations, such as point/line drawing, image
scaling, rotation, BitBLT, alpha blending and image blur/sharpness
The driver supports various operations from the rendering pipeline.
- copy
- fast solid color fill
- rotation
- flip
- alpha blending
The code in rga-hw.c is used to configure regs according to operations
The code in rga-buf.c is used to create private mmu table for RGA.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
changeset 6bbf7a855d ("media: dvbdev: convert DVB device types into an enum")
added a new warning on gcc 6:
>> drivers/media/dvb-core/dvbdev.c:86:1: warning: control reaches end of non-void function [-Wreturn-type]
That's because gcc is not smart enough to see that all types are
present at the switch. Also, the current code is not too optimized.
So, replace it to a more optimized one, based on a static table.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 6bbf7a855d ("media: dvbdev: convert DVB device types into an enum")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix a bunch of coding style issues found by checkpatch on the
part of the code that the previous patches touched.
WARNING: please, no space before tabs
+ * ^I^Icallback.$
ERROR: space required before the open parenthesis '('
+ switch(cmd) {
WARNING: line over 80 characters
+ err = dtv_property_process_get(fe, &getp, tvp + i, file);
WARNING: line over 80 characters
+ err = fe->ops.diseqc_recv_slave_reply(fe, (struct dvb_diseqc_slave_reply*) parg);
ERROR: "(foo*)" should be "(foo *)"
+ err = fe->ops.diseqc_recv_slave_reply(fe, (struct dvb_diseqc_slave_reply*) parg);
WARNING: line over 80 characters
+ err = fe->ops.read_signal_strength(fe, (__u16 *) parg);
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The functions used on dvb_demux.h are largely used on DVB drivers.
Yet, none of them are documented.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are three structs defined inside dvb_demux.h. None
of them are currently documented.
Add documentation for them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Simplify the get property handling and move it to the existing
code at dtv_property_process_get() directly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since all properties in the func dtv_property_process_set() use
at most 4 bytes arguments, change the code to pass
u32 cmd and u32 data as function arguments, instead of passing a
pointer to the entire struct dtv_property *tvp.
Instead of having a generic dtv_property_dump(), added its own
properties debug logic in the dtv_property_process_set().
Signed-off-by: Satendra Singh Thakur <satendra.t@samsung.com>
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of using an integer to represent it, use boolean,
as this better describes what this field really means.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The struct dvb_demux_filter.doneq is a boolean.
Mark it as such, as it helps to understand what it does.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kernel-doc allows documenting enums. Also, it makes clearer
about the meaning of each field on structures.
So, convert DMX_STATE_* to an enum.
While here, get rid of the unused DMX_STATE_SET.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kernel-doc allows documenting enums. Also, it makes clearer
about the meaning of each field on structures.
So, convert DMX_TYPE_* to an enum.
While here, get rid of the unused DMX_TYPE_PES.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several minor adjustments at the kernel-doc markups:
- some syntax fixes;
- some cross-references;
- add cross-references for the mentioned ioctls;
- some constants marked as such.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are several functions at the dvbdev that are common to all
digital TV device nodes with aren't documented.
Add documentation for them. No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Enums can be documented via kernel-doc. So, convert the
DVB_DEVICE_* macros to an enum.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are several problems with regards to the return of
FE_SET_PROPERTY. The original idea were to return per-property
return codes via tvp->result field, and to return an updated
set of values.
However, that never worked. What's actually implemented is:
- the FE_SET_PROPERTY implementation doesn't call .get_frontend
callback in order to get the actual parameters after return;
- the tvp->result field is only filled if there's no error.
So, it is always filled with zero;
- FE_SET_PROPERTY doesn't call memdup_user() nor any other
copy_to_user() function. So, any changes to the properties
will be lost;
- FE_SET_PROPERTY is declared as a write-only ioctl (IOW).
While we could fix the above, it could cause regressions.
So, let's just assume what the code really does, updating
the documentation accordingly and removing the logic that
would update the discarded tvp->result.
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Two readonly ioctls can't be allowed if the frontend device
is opened in read only mode. Explain why.
Reviewed by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are too much tabs on several properties, for no good
reason. That sounds confusing while reading the struct, so
adjust them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In the past, I guess the idea was to use state in order to
allow an autofush logic. However, in the current code, it is
used only for debug messages, on a poor man's solution, as
there's already a debug message to indicate when the properties
got flushed.
So, just get rid of it for good.
Reviewed-by: Shuah Khan <shuahkg@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently, there are two handlers for ioctls:
- dvb_frontend_ioctl_properties()
- dvb_frontend_ioctl_legacy()
Despite their names, both handles non-legacy DVB ioctls.
Besides that, there's no reason why to not handle all ioctls
on a single handler function.
So, merge them into a single function (dvb_frontend_handle_ioctl)
and reorganize the ioctl's to indicate what's the current DVB
API and what's deprecated.
Despite the big diff, the handling logic for each ioctl is the
same as before.
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use a switch() on this function, just like on other ioctl
handlers and handle parameters inside each part of the
switch.
That makes it easier to integrate with the already existing
ioctl handler function.
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Only lg2160 implement gets_property, but there's no need for that,
as no other driver calls this callback, as get_frontend() does the
same, and set_frontend() also calls lg2160 get_frontend().
So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This callback is not actually doing anything but making it to
return an error depending on the DTV frontend command. Well,
that could break userspace for no good reason, and, if needed,
should be implemented, instead, at set_frontend() callback.
So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The stv6110 has a weird code that checks if get_property
and set_property ioctls are defined. If they're, it initializes
a "srate" var from properties cache. Otherwise, it sets to
15MBaud, with won't make any sense.
Thankfully, it seems that someone else discovered the issue in
the past, as "srate" is currently not used anywhere!
So, get rid of that really weird dead code logic.
Reported-by: Honza Petrous <jpetrous@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver doesn't implement support for set_property(). Yet,
it implements a boilerplate for it. Get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As reported by Laurent, when a DVB frontend need to register
two drivers (e. g. a tuner and a demod), if the second driver
fails to register (for example because it was not compiled),
the error handling logic frees the frontend by calling
dvb_frontend_detach(). That used to work fine, but changeset
1f862a68df ("[media] dvb_frontend: move kref to struct dvb_frontend")
added a kref at struct dvb_frontend. So, now, instead of just
freeing the data, the error handling do a kref_put().
That works fine only after dvb_register_frontend() succeeds.
While it would be possible to add a helper function that
would be initializing earlier the kref, that would require
changing every single DVB frontend on non-trivial ways, and
would make frontends different than other drivers.
So, instead of doing that, let's focus on the real issue:
only call kref_put() after kref_init(). That's easy to
check, as, when the dvb frontend is successfuly registered,
it will allocate its own private struct. So, if such
struct is allocated, it means that it is safe to use
kref_put(). If not, then nobody is using yet the frontend,
and it is safe to just deallocate it.
Fixes: 1f862a68df ("[media] dvb_frontend: move kref to struct dvb_frontend")
Reported-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Without device tree, there is no way to use this driver.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ioctl LIRC_SET_REC_TIMEOUT would set a timeout of 704ns if called
with a timeout of 4294968us.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The tango HW IR decoder supports NEC, RC-5, RC-6 protocols.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a keymap for the Sigma Designs Vantage (dev board) remote control.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Without device tree, there is no way to use this driver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Without device tree, there is no way to use this driver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the kernel is built without device tree, this driver cannot be
used and without gpiolib it cannot control any gpio pin.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When receiving an nec repeat, rc_repeat() is called and then rc_keydown()
with the last decoded scancode. That last call is redundant.
Fixes: 265a2988d2 ("media: rc-core: consistent use of rc_repeat()")
Cc: <stable@vger.kernel.org> # v4.14
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are no users of this functionality (ir-lirc-codec.c has its own
implementation and lirc_zilog.c doesn't use it) so remove it.
This only affects users of the lirc kapi, not rc-core drivers.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The 0-day robot reports:
drivers/media/rc/gpio-ir-recv.c: In function 'gpio_ir_recv_irq':
>> drivers/media/rc/gpio-ir-recv.c:38:8: error: implicit declaration of function 'gpiod_get_value' [-Werror=implicit-function-declaration]
Fixes: eed008e605 ("[media] media: rc: gpio-ir-recv: use gpiolib API")
For some reason only partial patch was applied. Also include
gpio/consumer.h otherwise compile test fails.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Sean Young <sean@mess.org>
Update my imgtec.com and personal email address to my kernel.org one in
a few places as MIPS will soon no longer be part of Imagination
Technologies, and add mappings in .mailcap so get_maintainer.pl reports
the right address.
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The clock control is not explicitly controlled by the driver in two cases:
ACPI based systems and when the clock is part of the power sequence of the
camera module.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Obtain the clock rate from the clock framework if it's not available
through DT. The assumption is that the parent device (camera module)
defines the rate as clock control is a part of the power on and power off
sequences --- which are camera module specific.
Also use the clock rate from DT if no clock is provided.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The external clock frequency was set by the driver but the obtained
frequency was never verified. Do that.
Being able to obtain the exact frequency is important as the value is used
for PLL calculations which may result in frequencies that violate the PLL
tree limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The error handling code in smiapp_power_on() returned in case of a failed
I2C write instead of cleaning up the mess. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
ov13858 contained a 64-bit division. Use do_div() for calculating it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previously, with crop (0, 0), (4255, 3167), VTS < 0xC9E was resulting in
blank frames sometimes. This appeared as video flickering. But we need VTS
< 0xC9E to get ~30fps.
Omni Vision recommends to use crop (0,8), (4255, 3159) for 4224x3136. With
this crop, VTS 0xC8E is supported and yields ~30fps.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sakari Ailus