Commit Graph

160641 Commits

Author SHA1 Message Date
Linus Torvalds 225ff868e1 Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management & ACPI update from Zhang Rui,

Ho humm.  Normally these things go through Len.  But it's just three
small fixes, I guess I can pull directly too.

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  exynos4_tmu_driver_ids should be exynos_tmu_driver_ids.
  ACPI video: Ignore errors after _DOD evaluation.
  thermal: solve compilation errors in rcar_thermal
2012-11-03 15:25:14 -07:00
Linus Torvalds 209c510e36 Merge branch 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux
Pull i2c embedded fixes from Wolfram Sang:
 "Two patches are usual stuff.

  The bigger patch is needed to correct a wrong decision made in this
  merge window.  We hoped to get the PIOQUEUE mode in the mxs driver
  working with DMA, but it turned out to be too broken (leading to data
  loss), so we now think it is best to remove it entirely and work only
  with DMA now.  The patch should be in 3.7.  IMO, so users never get
  the chance to use both modes in parallel."

* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
  i2c: tegra: set irq name as device name
  i2c-nomadik: Fixup clock handling
  i2c: mxs: remove broken PIOQUEUE support
2012-11-03 15:14:54 -07:00
Linus Torvalds 53f9313f5c Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
 "Scattered selection of fixes:

   - radeon: load detect fixes from SuSE/AMD
   - intel: misc i830, sdvo regression, vesafb kickoff ums fix
   - exynos: maintainers entry update + fixes
   - udl: fix stride scanout issue

  it's slightly bigger than I'd probably like, but nothing looked
  dangerous enough to hold off on."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/udl: fix stride issues scanning out stride != width*bpp
  drm/radeon: add load detection support for ext DAC on R200 (v2)
  DRM/radeon: For single CRTC GPUs move handling of CRTC_CRT_ON to crtc_dpms().
  DRM/Radeon: Fix TV DAC Load Detection for single CRTC chips.
  DRM/Radeon: Clean up code in TV DAC load detection.
  drm/radeon: fix ATPX function documentation
  drivers/gpu/drm/radeon/evergreen_cs.c: Remove unnecessary semicolon
  DRM/Radeon: On DVI-I use Load Detection when EDID is bogus.
  DRM/Radeon: Fix primary DAC Load Detection for RV100 chips.
  DRM/Radeon: Fix Load Detection on legacy primary DAC.
  drm: exynos: removed warning due to missing typecast for mixer driver data
  drm/exynos: add support for ARCH_MULTIPLATFORM
  MAINTAINERS: Add git repository for Exynos DRM
  drm/exynos: fix display on issue
  drm/i915: Only kick out vesafb if we takeover the fbcon with KMS
  drm/i915: be less verbose about inability to provide vendor backlight
  drm/i915: clear the entire sdvo infoframe buffer
  drm/i915: VGA needs to be on pipe A on i830M
  drm/i915: fix overlay on i830M
2012-11-03 15:13:49 -07:00
Linus Torvalds 0f89a5733a Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull networking fixes from David Miller:
 "First post-Sandy pull request"

 1) Fix antenna gain handling and initialization of chan->max_reg_power
    in wireless, from Felix Fietkau.

 2) Fix nexthop handling in H.232 conntrack helper, from Julian
    Anastasov.

 3) Only process 80211 mesh config header in certain kinds of frames,
    from Javier Cardona.

 4) 80211 management frame header length needs to be validated, from
    Johannes Berg.

 5) Don't access free'd SKBs in ath9k driver, from Felix Fietkay.

 6) Test for permanent state correctly in VXLAN driver, from Stephen
    Hemminger.

 7) BNX2X bug fixes from Yaniv Rosner and Dmitry Kravkov.

 8) Fix off by one errors in bonding, from Nikolay ALeksandrov.

 9) Fix divide by zero in TCP-Illinois congestion control.  From Jesper
    Dangaard Brouer.

10) TCP metrics code says "Yo dawg, I heard you like sizeof, so I did a
    sizeof of a sizeof, so you can size your size" Fix from Julian
    Anastasov.

11) Several drivers do mdiobus_free without first doing an
    mdiobus_unregister leading to stray pointer references.  Fix from
    Peter Senna Tschudin.

12) Fix OOPS in l2tp_eth_create() error path, it's another danling
    pointer kinda situation.  Fix from Tom Parkin.

13) Hardware driven by the vmxnet driver can't handle larger than 16K
    fragments, so split them up when necessary.  From Eric Dumazet.

14) Handle zero length data length in tcp_send_rcvq() properly.  Fix
    from Pavel Emelyanov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
  tcp-repair: Handle zero-length data put in rcv queue
  vmxnet3: must split too big fragments
  l2tp: fix oops in l2tp_eth_create() error path
  cxgb4: Fix unable to get UP event from the LLD
  drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free
  drivers/net/ethernet/nxp/lpc_eth.c: Call mdiobus_unregister before mdiobus_free
  bnx2x: fix HW initialization using fw 7.8.x
  tcp: Fix double sizeof in new tcp_metrics code
  net: fix divide by zero in tcp algorithm illinois
  net: sctp: Fix typo in net/sctp
  bonding: fix second off-by-one error
  bonding: fix off-by-one error
  bnx2x: Disable FCoE for 57840 since not yet supported by FW
  bnx2x: Fix no link on 577xx 10G-baseT
  bnx2x: Fix unrecognized SFP+ module after driver is loaded
  bnx2x: Fix potential incorrect link speed provision
  bnx2x: Restore global registers back to default.
  bnx2x: Fix link down in 57712 following LFA
  bnx2x: Fix 57810 1G-KR link against certain switches.
  ixgbe: PTP get_ts_info missing software support
  ...
2012-11-02 20:48:41 -07:00
Eric Dumazet a4d7e485bc vmxnet3: must split too big fragments
vmxnet3 has a 16Kbytes limit per tx descriptor, that happened to work
as long as we provided PAGE_SIZE fragments.

Our stack can now build larger fragments, so we need to split them to
the 16kbytes boundary.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: jongman heo <jongman.heo@samsung.com>
Tested-by: jongman heo <jongman.heo@samsung.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Reviewed-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-02 21:58:09 -04:00
Jonghwan Choi 3ae53b1e13 exynos4_tmu_driver_ids should be exynos_tmu_driver_ids.
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2012-11-03 09:52:55 +08:00
Igor Murzov fba4e08736 ACPI video: Ignore errors after _DOD evaluation.
There are systems where video module known to work fine regardless
of broken _DOD and ignoring returned value here doesn't cause
any issues later. This should fix brightness controls on some laptops.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47861

Signed-off-by: Igor Murzov <e-mail@date.by>
Reviewed-by: Sergey V <sftp.mtuci@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2012-11-03 09:52:54 +08:00
Devendra Naga 608f62b996 thermal: solve compilation errors in rcar_thermal
following were the errors reported

drivers/thermal/rcar_thermal.c: In function ‘rcar_thermal_probe’:
drivers/thermal/rcar_thermal.c:214:10: warning: passing argument 3 of ‘thermal_zone_device_register’ makes integer from pointer without a cast [enabled by default]
include/linux/thermal.h:166:29: note: expected ‘int’ but argument is of type ‘struct rcar_thermal_priv *’
drivers/thermal/rcar_thermal.c:214:10: error: too few arguments to function ‘thermal_zone_device_register’
include/linux/thermal.h:166:29: note: declared here
make[1]: *** [drivers/thermal/rcar_thermal.o] Error 1
make: *** [drivers/thermal/rcar_thermal.o] Error 2

with gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5)

Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2012-11-03 09:52:48 +08:00
Vipul Pandya e3c9851278 cxgb4: Fix unable to get UP event from the LLD
If T4 configuration file gets loaded from the /lib/firmware/cxgb4/ directory
then offload capabilities of the cards were getting disabled during
initialization. Hence ULDs do not get an UP event from the LLD.

Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-02 21:41:29 -04:00
Peter Senna Tschudin aa731872f7 drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free
Based on commit b27393aecf

Calling mdiobus_free without calling mdiobus_unregister causes
BUG_ON(). This patch fixes the issue.

The semantic patch that found this issue(http://coccinelle.lip6.fr/):
// <smpl>
@@
expression E;
@@
  ... when != mdiobus_unregister(E);

+ mdiobus_unregister(E);
  mdiobus_free(E);
// </smpl>

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-02 21:36:06 -04:00
Peter Senna Tschudin 57c10b61c8 drivers/net/ethernet/nxp/lpc_eth.c: Call mdiobus_unregister before mdiobus_free
Based on commit b27393aecf

Calling mdiobus_free without calling mdiobus_unregister causes
BUG_ON(). This patch fixes the issue.

The semantic patch that found this issue(http://coccinelle.lip6.fr/):
// <smpl>
@@
expression E;
@@
  ... when != mdiobus_unregister(E);

+ mdiobus_unregister(E);
  mdiobus_free(E);
// </smpl>

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-02 21:36:06 -04:00
Dmitry Kravkov 2b674047be bnx2x: fix HW initialization using fw 7.8.x
Since commit 96bed4b9 (use FW 7.8.2) BRB HW block needs to be
initialized using fw values for all devices.
Otherwise ETS on 57712/578xx will not work.

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-02 21:32:11 -04:00
Linus Torvalds a315b5a6d4 Power management update for 3.7-rc4
Change the email address of the powernow-k8 maintainer.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iQIcBAABAgAGBQJQlFWVAAoJEKhOf7ml8uNsi7MQAI5FZNla5D7fXf6JuI4n53S6
 2aLFzkf9q0ievYBBeyDphLnmIWS44yfJN+OKyhvyd/BF4tlvmrZVzUjMHAFWaLe6
 Eza8wRgtc8igGgQtE06xpnmaYOfNUU4B408SU+SqSurIvV9s2s1F3t8+gBaCPymk
 9UxYVaE1rAHxTLzoDryhQ3H2GbWle08e44ce5kLW1GEGbC0B6l6Dfsrag+lzPedd
 5QNBcoq+Fv0kvzSUJFNDwMwGrg5F7KL21EsfRJtPLXPVtMRTO1OdL1enWLDOE+jw
 K0lpw/GQQx7sqyPRHrH4hTZrPHfzeY2mRAl/Q3pro/nqEy4jhfQjrH3G0s8o/xgQ
 w1sKf0rDmUSA2+FhcGEMWm/eMYOE1oOyZVdxn0B1e8gN5yOqXfyho0CIvz8YMyAy
 DoCjURor92teddNF83THKTDlIK248x4eCKThDIXleYE+t5th6aQdHoeQgmXQ4Y+g
 eTUjFnT0glxWpyhoeTHSvhd61xgYU3aRG99OX/Y5teIIHW5rUyXhd9O1hl53UoVt
 SSq7V5LRxJTU+hnW/FX19B/1/XfDe5BW6Z9+yGtibGHq4sSCb1yJeWaLOVCg3u3D
 TOdbtl14ohq+zvs9MhKyTOxh710I+e10CGQHqY61MK5n+seG6YZw98GAepLQqnMW
 T4VZrJBNCrXd94+4OxcU
 =jN09
 -----END PGP SIGNATURE-----

Merge tag 'pm-for-3.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull power management update from Rafael J. Wysocki:
 "Change the email address of the powernow-k8 maintainer."

* tag 'pm-for-3.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq / powernow-k8: Change maintainer's email address
2012-11-02 16:56:39 -07:00
Linus Torvalds 74fb838cd4 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem fixes from Dmitry Torokhov:
 "Just a few driver fixes."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: tsc40 - remove wrong announcement of pressure support
  Input: lpc32xx-keys - select INPUT_MATRIXKMAP
  Input: pxa27x_keypad - clear pending interrupts on keypad config
  Input: wacom - correct bad Cintiq 24HD check
  Input: wacom - add INPUT_PROP_DIRECT flag to Cintiq 24HD
  Input: egalax_ts - get gpio from devicetree
2012-11-02 16:11:15 -07:00
Linus Torvalds 23e44302b3 Merge git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull more scsi target fixes from Nicholas Bellinger:
 "This series is a second round of target fixes for v3.7-rc4 that have
  come into target-devel over the last days, and are important enough to
  be applied ASAP.

  All are being CC'ed to stable.  The most important two are:

   - target: Re-add explict zeroing of INQUIRY bounce buffer memory to
     fix a regression for handling zero-length payloads, a bug that went
     during v3.7-rc1, and hit >= v3.6.3 stable.  (nab + paolo)

   - iscsi-target: Fix a long-standing missed R2T wakeup race in TX
     thread processing when using a single queue slot.  (Roland)

  Thanks to Roland & PureStorage team for helping to track down this
  long standing race with iscsi-target single queue slot operation.

  Also, the tcm_fc(FCoE) regression bug that was observed recently with
  -rc2 code has also been resolved with the cancel_delayed_work() return
  bugfix (commit c0158ca64da5: "workqueue: cancel_delayed_work() should
  return %false if work item is idle") now in -rc3.  Thanks again to Yi
  Zou, MDR, Robert Love @ Intel for helping to track this down."

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target: Fix incorrect usage of nested IRQ spinlocks in ABORT_TASK path
  iscsi-target: Fix missed wakeup race in TX thread
  target: Avoid integer overflow in se_dev_align_max_sectors()
  target: Don't return success from module_init() if setup fails
  target: Re-add explict zeroing of INQUIRY bounce buffer memory
2012-11-02 15:08:20 -07:00
Linus Torvalds ae41fce3cc An e-mail address update, and fix a compile error on SPARC
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJQk+S8AAoJEMsfJm/On5mB29gP/3sJkPGvtaVVgBbncmj0ySNc
 Bi3X7Dg1ud+WmkDBTp8SQmzf/Zd3lRYDdL+b3mfltjLigMbXtn6eUOb8IJ6jEfgK
 Qs20umnDHLu6dxqrH36pcTyU4bEAdnG+daZtJuQhSA+wvfDLujxHGiTBEdN+VqWt
 CjSY0nqfBvJfETEuucZNLr5Lo5oVQFIqS8PAkcaV+7we601Y918XUiETXBXuHQh7
 GuoP10bGIKh9IDUSBEdT/R5ntvytKyCNp5QPwvujw2NITDwh/Z/pTcG3YgfR8Jrc
 7rJMI6jZ6VZTp7NLKuvNHEtZ4EQFgjRn1huq6ac4PGQUOWXS+HJBu54XfjHN4VMZ
 NPj1bJ07GxeysAr9aspUxWwFWrRo49v0p24RtqMNsafGUfyg2PLcgKB1YGQuzzyy
 8ZPYx2rUE4uRChB4tc6pgebUDH6uh/ODP+/SAaceUTJ1z9dnOezW2/VsJswzlnpi
 FlmjeEHu22+JMiPeNVpB0+ezV3f+bs4dkLt+hjOVG/5qIsH6sfK+kO4kKuE6nIB0
 XgslG/NEcdZVwwksl5dn1oCLEB1KOfXJZsgFVTkbOWJ97ueCz/sLI4+18Blrh/7h
 1jwu9JOT7mADscRujQ/gwiqdTGHcE2T/5vnREZTUG6AIUSEvLp/C97uYcEjOmwZA
 Kyqs7C1Zslgz0cF33NuU
 =REN0
 -----END PGP SIGNATURE-----

Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:
 "An e-mail address update, and fix a compile error on SPARC"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: Only include of_match_table with CONFIG_OF_GPIO
  hwmon, fam15h_power: Change email address, MAINTAINERS entry
2012-11-02 13:27:52 -07:00
Linus Torvalds 66b6a0c979 Bug-fixes:
* Use appropriate macros instead of hand-rolling our own (ARM).
  * Fixes if FB/KBD closed unexpectedly.
  * Fix memory leak in /dev/gntdev ioctl calls.
  * Fix overflow check in xenbus_file_write.
  * Document cleanup.
  * Performance optimization when migrating guests.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQEcBAABAgAGBQJQk9ngAAoJEFjIrFwIi8fJXOcH/jEmTaV2rbUCCnnivlQGj5B2
 AAXt03MM2F7Ohifo8IEHDhvJlUqQnglQq4wcku/8X/bqSkxtqJMfa/UAStmS2e6r
 605msiMws/GKiDPgKywWHjMPk7JJow/T7du9mpT2Swla12+DXc7e0P6Sqm6qGtB5
 tCBFYe3CS+j8Xi/siPhveAoLoDVmC8RpNzV8EWBdUKhNeD6U4s5M3+ChVexOrB/6
 43YkzurkY/FOsP+8YhNnKFSFrpYleRB1GdFcr8PN5mv85sNKts7vHCb4qJFzZdbk
 BMImdLrTUnKArE4y4FS0iqabOTGXaUplEXfyxDw5hweESGa1qzrd29ocyMQ5p/U=
 =LQxc
 -----END PGP SIGNATURE-----

Merge tag 'stable/for-linus-3.7-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull Xen bugfixes from Konrad Rzeszutek Wilk:
 - Use appropriate macros instead of hand-rolling our own (ARM).
 - Fixes if FB/KBD closed unexpectedly.
 - Fix memory leak in /dev/gntdev ioctl calls.
 - Fix overflow check in xenbus_file_write.
 - Document cleanup.
 - Performance optimization when migrating guests.

* tag 'stable/for-linus-3.7-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/mmu: Use Xen specific TLB flush instead of the generic one.
  xen/arm: use the __HVC macro
  xen/xenbus: fix overflow check in xenbus_file_write()
  xen-kbdfront: handle backend CLOSED without CLOSING
  xen-fbfront: handle backend CLOSED without CLOSING
  xen/gntdev: don't leak memory from IOCTL_GNTDEV_MAP_GRANT_REF
  x86: remove obsolete comment from asm/xen/hypervisor.h
2012-11-02 13:26:11 -07:00
Laxman Dewangan 91b370a0db i2c: tegra: set irq name as device name
When watching the irqs name of tegra i2c, all instances
irq name shows as tegra_i2c.

Passing the device name properly to have the irq names with
instance like tegra-i2c.0, tegra-i2c.1 etc.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-02 10:52:52 +01:00
Philippe Begnic 817315f574 i2c-nomadik: Fixup clock handling
Make sure to clk_prepare as well as clk_enable.

Signed-off-by: Philippe Begnic <philippe.begnic@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-02 10:52:52 +01:00
Wolfram Sang 82fa63bd6b i2c: mxs: remove broken PIOQUEUE support
This I2C master can do DMA and PIOQUEUE (PIO with FIFO). Originally,
only PIOQUEUE was supported and it had issues, then DMA support was added
this cycle. The original intention was to keep PIOQUEUE since it has
less overhead what is nice for small transfers. However, runtime
switching between PIOQEUE and DMA depending on the transfer size never
worked despite a lot of trying. Since PIOQUEUE mode itself was flaky
(polling at places where interrupts failed to work) and the
implementation also imposed a size limit for transfers, it is best to
remove the support, so users don't fall over its limitations. It also
makes the driver a lot cleaner and more robust. If somebody really wants
less overhead, plain PIO mode could still be implemented with the
addidtional advantage that this mode is also available on MX23, too.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
2012-11-02 10:52:32 +01:00
Dave Airlie 3916e1d71b drm/udl: fix stride issues scanning out stride != width*bpp
When buffer sharing with the i915 and using a 1680x1050 monitor,
the i915 gives is a 6912 buffer for the 6720 width, the code doesn't
render this properly as it uses one value to set the base address for
reading from the vmap and for where to start on the device.

This fixes it by calculating the values correctly for the device and
for the pixmap. No idea how I haven't seen this before now.

Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
2012-11-02 10:31:37 +10:00
Jamie Lentin eaa7cc60f7 hwmon: Only include of_match_table with CONFIG_OF_GPIO
The following fixes build errors on sparc. Without any DT support,
of_match_ptr is NULL and the below is a no-op. However, if just
CONFIG_OF is defined then so is of_match_ptr.

All useful parts of the gpio-fan DT support rely on CONFIG_OF_GPIO
anyway, so of_match_table should too.

Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2012-11-01 17:31:20 -07:00
Dave Airlie a2e4919a7e Merge branch 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
Inki writes:
"As I posted before, we have added a new git repository for Exynos drm
to MAINTAINERS file so change it to new one like below,
   from git://git.infradead.org/users/kmpark/linux-samsung
   to git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos

And this pull request includes the following:
- fix display on issue when user requested dpms mode changing.
- add git repository for Exynos drm to MAINTAINERS file.
- add support for ARCH_MULTIPLATFORM.
- and code clean."

* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
  drm: exynos: removed warning due to missing typecast for mixer driver data
  drm/exynos: add support for ARCH_MULTIPLATFORM
  MAINTAINERS: Add git repository for Exynos DRM
  drm/exynos: fix display on issue
2012-11-02 10:30:42 +10:00
Dave Airlie b7a46dcf7a Merge branch 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Alex writes:
"This request is mostly load detection fixes from Egbert and me."

* 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: add load detection support for ext DAC on R200 (v2)
  DRM/radeon: For single CRTC GPUs move handling of CRTC_CRT_ON to crtc_dpms().
  DRM/Radeon: Fix TV DAC Load Detection for single CRTC chips.
  DRM/Radeon: Clean up code in TV DAC load detection.
  drm/radeon: fix ATPX function documentation
  drivers/gpu/drm/radeon/evergreen_cs.c: Remove unnecessary semicolon
  DRM/Radeon: On DVI-I use Load Detection when EDID is bogus.
  DRM/Radeon: Fix primary DAC Load Detection for RV100 chips.
  DRM/Radeon: Fix Load Detection on legacy primary DAC.
2012-11-02 10:29:47 +10:00
Dave Airlie 9c275407a3 Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel Vetter writes"
Nothing big at all for -fixes, just small stuff:
- Two patches to fix bugs on i830M
- ums regression fixer due to kicking firmeware fbs (Chris)
- tune down a too loud warning (Jani)
- be more careful with sdvo infoframes, which fixes a long-standing
  sdvo-hdmi regression"

* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
  drm/i915: Only kick out vesafb if we takeover the fbcon with KMS
  drm/i915: be less verbose about inability to provide vendor backlight
  drm/i915: clear the entire sdvo infoframe buffer
  drm/i915: VGA needs to be on pipe A on i830M
  drm/i915: fix overlay on i830M
2012-11-02 10:26:39 +10:00
nikolay@redhat.com c84e1590d1 bonding: fix second off-by-one error
Fix off-by-one error because IFNAMSIZ == 16 and when this
code gets executed we stick a NULL byte where we should not.

How to reproduce:
 with CONFIG_CC_STACKPROTECTOR=y (otherwise it may pass by silently)
 modprobe bonding; echo 1 > /sys/class/net/bond0/bonding/mode;
 echo "AAAAAAAAAAAAAAAA" > /sys/class/net/bond0/bonding/active_slave;

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>

Note: Sorry for the second patch but I missed this one while checking
      the file. You can squash them into one patch.
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-01 11:53:44 -04:00
nikolay@redhat.com eb6e98a1b2 bonding: fix off-by-one error
Fix off-by-one error because IFNAMSIZ == 16 and when this
code gets executed we stick a NULL byte where we should not.

How to reproduce:
 with CONFIG_CC_STACKPROTECTOR=y (otherwise it may pass by silently)
 modprobe bonding; echo 1 > /sys/class/net/bond0/bonding/mode;
 echo "AAAAAAAAAAAAAAAA" > /sys/class/net/bond0/bonding/primary;

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-01 11:53:43 -04:00
Dmitry Kravkov 477864ddd3 bnx2x: Disable FCoE for 57840 since not yet supported by FW
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-01 11:31:55 -04:00
Yaniv Rosner 03c31488a0 bnx2x: Fix no link on 577xx 10G-baseT
Since the Warpcore supports various link types, need to set only the correct
supported modes for XFI which is the serdes interface for the 10G-baseT PHY.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-01 11:31:54 -04:00
Yaniv Rosner e82041df5d bnx2x: Fix unrecognized SFP+ module after driver is loaded
When SFP+ module is plugged in after driver is already loaded, it may not be
recognized, so set SFP module recognition time up to 300ms, without resetting
the module power in the middle.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-01 11:31:54 -04:00
Yaniv Rosner 4978140c38 bnx2x: Fix potential incorrect link speed provision
Fix possible incorrect link speed provision following rapid link speed change.
Clear link speed mask after each link change, and not only after link down.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-01 11:31:54 -04:00
Yaniv Rosner cd1a26a3bb bnx2x: Restore global registers back to default.
Several KR registers were not set correctly back to default after
loopback test, so set those global registers over the global WC lane (zero)
rather than the current lane.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-01 11:31:53 -04:00
Yaniv Rosner a75bb00100 bnx2x: Fix link down in 57712 following LFA
In case of link flap avoidance between PXE boot and bnx2x, set the appropriate
PHY DEVAD even if LFA kicks in.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-01 11:31:52 -04:00
Yaniv Rosner b457bcb972 bnx2x: Fix 57810 1G-KR link against certain switches.
Fix 1G KR link by restoring CL72 misc control register to default value rather
than 0.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-01 11:31:51 -04:00
Jacob Keller 50f8d35de8 ixgbe: PTP get_ts_info missing software support
This patch corrects the ethtool get_ts_info functon which did not state that
software timestamping was supported, even though it is.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
CC: Stable <stable@vger.kernel.org> [3.5]
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-01 11:22:34 -04:00
Alex Deucher 6d9cdfc271 drm/radeon: add load detection support for ext DAC on R200 (v2)
The R200 asics use an external DAC for the secondary DAC.
The current KMS code tries to use code for the integrated
TV DAC for R200 which leads to unpredictable results since
R200 does not have an integrated TV DAC. This patch ports
the external DAC load detection support from the UMS
driver to KMS.

v2: fix typo in loop break logic

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Egbert Eich <eich@suse.de>
2012-11-01 10:34:34 -04:00
Egbert Eich f8c4d701ae DRM/radeon: For single CRTC GPUs move handling of CRTC_CRT_ON to crtc_dpms().
On all dual CRTC GPUs the CRTC_CRT_ON in the RADEON_CRTC_EXT_CNTL register
 controls the CRTC of the primary DAC. Therefore it is set in the DAC DMPS
function.
This is different for GPU's with a single CRTC but a primary and a
TV DAC: here it controls the single CRTC no matter where it is routed.
Therefore we set it here. This avoids an elaborate on/off state tracking
since both primary_dac_dpms() and tv_dac_dpms() functions would have
to touch this bit.
On single CRTC GPUs with just one DAC it's irrelevant where this bit
is handled.

agd5f: fix warning

Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2012-11-01 10:34:34 -04:00
Egbert Eich 701337dc27 DRM/Radeon: Fix TV DAC Load Detection for single CRTC chips.
The RN50 has a TV DAC but only a single CRTC. For load detection this
DAC is controlled by the primary CRTC.

Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2012-11-01 10:34:33 -04:00
Egbert Eich d038db8698 DRM/Radeon: Clean up code in TV DAC load detection.
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2012-11-01 10:34:32 -04:00
Igor Murzov dfdcbebc54 drm/radeon: fix ATPX function documentation
Fix a copy&pasted documentation.

Signed-off-by: Igor Murzov <e-mail@date.by>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2012-11-01 10:34:32 -04:00
Peter Senna Tschudin 74e4ca32a4 drivers/gpu/drm/radeon/evergreen_cs.c: Remove unnecessary semicolon
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r1@
statement S;
position p,p1;
@@
S@p1;@p

@script:python r2@
p << r1.p;
p1 << r1.p1;
@@
if p[0].line != p1[0].line_end:
        cocci.include_match(False)
@@
position r1.p;
@@
-;@p
// </smpl>

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2012-11-01 10:34:31 -04:00
Egbert Eich fc87f13b8d DRM/Radeon: On DVI-I use Load Detection when EDID is bogus.
The Radeon driver uses the analog/digital flag to determine if the
DAC or the TMDS encoder should be enabled on a DVI-I connector.
If the EDID is bogus this flag is no longer reliable. This fix
adds a fallback to DAC load detection to determine if anything
is connected to the DAC. If not and a (bogus) EDID is found it
assumes a digital display is connected.
This works around problems with some crappy IPMI devices using
Radeon ES1000.

Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2012-11-01 10:34:31 -04:00
Egbert Eich 9c50b1d937 DRM/Radeon: Fix primary DAC Load Detection for RV100 chips.
For Radeon 7500 ATI recommends a DAC_FORCE value of 0x1ac. This value
works better on ES1000 (RV100) chips, too, as it doesn't produce any false
positives on any cards I have tested. Therefore let's assume that this
value is good for all RV100 and RV200 chipset generations.

Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2012-11-01 10:34:30 -04:00
Egbert Eich 83325d0721 DRM/Radeon: Fix Load Detection on legacy primary DAC.
An uninitialized variable led to broken load detection.

Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
2012-11-01 10:34:16 -04:00
Steve Hodgson ab74b3d62f target: Fix incorrect usage of nested IRQ spinlocks in ABORT_TASK path
This patch changes core_tmr_abort_task() to use spin_lock -> spin_unlock
around se_cmd->t_state_lock while spin_lock_irqsave is held via
se_sess->sess_cmd_lock.

Signed-off-by: Steve Hodgson <steve@purestorage.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2012-11-01 00:38:45 -07:00
Roland Dreier d5627acba9 iscsi-target: Fix missed wakeup race in TX thread
The sleeping code in iscsi_target_tx_thread() is susceptible to the classic
missed wakeup race:

 - TX thread finishes handle_immediate_queue() and handle_response_queue(),
   thinks both queues are empty.
 - Another thread adds a queue entry and does wake_up_process(), which does
   nothing because the TX thread is still awake.
 - TX thread does schedule_timeout() and sleeps forever.

In practice this can kill an iSCSI connection if for example an initiator
does single-threaded writes and the target misses the wakeup window when
queueing an R2T; in this case the connection will be stuck until the
initiator loses patience and does some task management operation (or kills
the connection entirely).

Fix this by converting to wait_event_interruptible(), which does not
suffer from this sort of race.

Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2012-11-01 00:38:44 -07:00
Roland Dreier 3e03989b58 target: Avoid integer overflow in se_dev_align_max_sectors()
The expression (max_sectors * block_size) might overflow a u32
(indeed, since iblock sets max_hw_sectors to UINT_MAX, it is
guaranteed to overflow and end up with a much-too-small result in many
common cases).  Fix this by doing an equivalent calculation that
doesn't require multiplication.

While we're touching this code, avoid splitting a printk format across
two lines and use pr_info(...) instead of printk(KERN_INFO ...).

Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2012-11-01 00:38:44 -07:00
Roland Dreier 0d0f9dfb31 target: Don't return success from module_init() if setup fails
If the call to core_dev_release_virtual_lun0() fails, then nothing
sets ret to anything other than 0, so even though everything is
torn down and freed, target_core_init_configfs() will seem to succeed
and the module will be loaded.  Fix this by passing the return value
on up the chain.

Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2012-11-01 00:38:31 -07:00
Nicholas Bellinger dea5f0998a target: Re-add explict zeroing of INQUIRY bounce buffer memory
This patch fixes a regression in spc_emulate_inquiry() code where the
local scope bounce buffer was no longer getting it's memory zeroed,
causing various problems with SCSI initiators that depend upon areas
of INQUIRY EVPD=0x83 payload having been zeroed.

This bug was introduced with the following v3.7-rc1 patch + CC'ed
stable commit:

commit ffe7b0e932
Author: Paolo Bonzini <pbonzini@redhat.com>
Date:   Fri Sep 7 17:30:38 2012 +0200

    target: support zero allocation length in INQUIRY

Go ahead and re-add the missing memset of bounce buffer memory to be
copied into the outgoing se_cmd descriptor kmapped SGL payload.

Reported-by: Kelsey Prantis <kelsey.prantis@intel.com>
Cc: Kelsey Prantis <kelsey.prantis@intel.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2012-10-31 22:17:12 -07:00
Linus Torvalds 1e207eb1c3 Merge git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull scsi target fixes from Nicholas Bellinger:
 "These are the current target pending fixes headed for v3.7-rc4 code.
  This includes the following highlights:

   - Fix long-standing qla2xxx target bug where certain fc_port_t state
     transitions could cause the internal session b-tree list to become
     out-of-sync.  (Roland)
   - Fix task management double free of se_cmd descriptor in exception
     path for users of target_submit_tmr().  (nab)
   - Re-introduce simple NOP emulation of REZERO_UNIT, SEEK_6, and
     SEEK_10 SCSI-2 commands in order to support legacy initiators that
     still require them.  (Bernhard)

  Note these three patches are also CC'ed to stable.

  Also, there a couple of outstanding (external) regressions that are
  still being tracked down for tcm_fc(FCoE) and tcm_vhost fabrics for
  v3.7.0 code, so please expect another PULL as these issues identified
  -> resolved."

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target: reintroduce some obsolete SCSI-2 commands
  target: Fix double-free of se_cmd in target_complete_tmr_failure
  qla2xxx: Update target lookup session tables when a target session changes
  tcm_qla2xxx: Format VPD page 83h SCSI name string according to SPC
  qla2xxx: Add missing ->vport_slock while calling qlt_update_vp_map
2012-10-31 15:42:08 -07:00