Reorder functions such that SFF and BMDMA functions are grouped.
While at it, s/BMDMA/SFF in a few comments where it actually meant
SFF.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ATA_FLAG_DISABLED is only used by drivers which don't use
->error_handler framework and is largely broken. Its only meaningful
function is to make irq handlers skip processing if the flag is set,
which is largely useless and even harmful as it makes those ports more
likely to cause IRQ storms.
Kill ATA_FLAG_DISABLED and makes the callers disable attached devices
instead. ata_port_probe() and ata_port_disable() which manipulate the
flag are also killed.
This simplifies condition check in IRQ handlers. While updating IRQ
handlers, remove ap NULL check as libata guarantees consecutive port
allocation (unoccupied ports are initialized with dummies) and
long-obsolete ATA_QCFLAG_ACTIVE check (checked by ata_qc_from_tag()).
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_irq_on() was renamed to ata_sff_irq_on() and exported a while ago
but prototype for the original function lingered in
drivers/ata/libata.h. Kill it. Also, ata_dev_select() is only used
inside drivers/ata/libata-sff.c. Make it static.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Clearing IRQ from ata_sff_error_handler() is necessary only when the
port is gonna be thawed before performing EH actions and some
controllers don't like being accessed after certain failure modes
until they're reset. Clear IRQ iff the port is being thawed.
* When the controller succesfully indicated bus error, the point of
thawing doesn't matter. Move thawing inside bmdma part of EH. This
is a bit ugly but will ease code reorganization later.
* Remove the unneeded ata_sff_sync().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We don't need to stall and wait after loading the task file and before
issuing a command, so don't do it. This shows up on profiles and is not
needed.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
page_mapping() check this via VM_BUG_ON(PageSlab(page)) so we bug here
with the according debuging turned on.
Future TODO: replace this with a flush_dcache_page_for_pio() API
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
Now, with the introduction of the sff_set_devctl() method, we can
use it in sff_irq_on() method too -- that way its implementations
in 'pata_bf54x' and 'pata_scc' become virtually identical to
ata_sff_irq_on(). The sff_irq_on() method now becomes quite
superfluous, and the only reason not to remove it completely is
the existence of the 'pata_octeon_cf' driver which implements it
as an empty function. Just make the method optional then, with
ata_sff_irq_on() becoming generic taskfile-bound function, still
global for the 'pata_bf54x' driver to be able to call it from its
thaw() and postreset() methods.
While at it, make the sff_irq_on() method and ata_sff_irq_on() return
'void' as the result is always ignored anyway.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The set of libata's taskfile access methods is clearly incomplete as
it lacks a method to write to the device control register -- which
forces drivers like 'pata_bf54x' and 'pata_scc' to implement more
"high level" (and more weighty) methods like freeze() and postreset().
So, introduce the optional sff_set_devctl() method which the drivers
only have to implement if the standard iowrite8() can't be used (just
like the existing sff_check_altstatus() method) and make use of it
in the freeze() and postreset() method implementations (I could also
have used it in softreset() method but it also reads other taskfile
registers without using tf_read() making that quite pointless);
this makes freeze() method implementations in the 'pata_bf54x' and
'pata_scc' methods virtually identical to ata_sff_freeze(), so we
can get rid of them completely.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On configurations where IRQ line is shared with a different
controller, spurious IRQs may happen continuously. The message was
put there primarily for debugging anyway. Kill it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Commit 27943620cb introduced spurious
IRQ handling but it has a race condition where valid completion can be
lost while trying to clear spurious IRQ leading to occassional command
timeouts.
This patch improves SFF interrupt handler such that
1. Once BMDMA HSM is stopped, the condition is never considered
spurious. As there's no way to resume stopped BMDMA HSM, if device
status doesn't agree with BMDMA status, the only way out is
aborting the command (otherwise, it will just end up timing out).
2. ap->ops->sff_check_status() can be safely called to clear spurious
device IRQ as it atomically returns completion status but BMDMA IRQ
status can't be cleared in safe way if command is in flight. After
a spurious IRQ, call ap->ops->sff_irq_clear() only if the
respective device is idle and retry completion if
sff_check_status() indicates command completion.
Please note that ata_piix uses bmdma_status for sff_irq_check() and #2
won't weaken spurious IRQ handling even with in-flight command because
if bmdma_status indicates IRQ pending but device status is not on
spurious check, the next IRQ handler invocation will abort the command
due to #1.
This fixes bko#15537.
https://bugzilla.kernel.org/show_bug.cgi?id=15537
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Andrew Benton <b3nton@gmail.com>
Cc: Petr Uzel <petr.uzel@centrum.cz>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This allows parallel scan and the like to be set without having to stop
using the existing full helper functions. This patch merely adds the argument
and fixes up the callers. It doesn't undo the special cases already in the
tree or add any new parallel callers.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Traditional IDE interface sucks in that it doesn't have a reliable IRQ
pending bit, so if the controller raises IRQ while the driver is
expecting it not to, the IRQ won't be cleared and eventually the IRQ
line will be killed by interrupt subsystem. Some controllers have
non-standard mechanism to indicate IRQ pending so that this condition
can be detected and worked around.
This patch adds an optional operation ->sff_irq_check() which will be
called for each port from the ata_sff_interrupt() if an unexpected
interrupt is received. If the operation returns %true,
->sff_check_status() and ->sff_irq_clear() will be cleared for the
port. Note that this doesn't mark the interrupt as handled so it
won't prevent IRQ subsystem from killing the IRQ if this mechanism
fails to clear the spurious IRQ.
This patch also implements ->sff_irq_check() for ata_piix. Note that
this adds slight overhead to shared IRQ operation as IRQs which are
destined for other controllers will trigger extra register accesses to
check whether IDE interrupt is pending but this solves rare screaming
IRQ cases and for some curious reason also helps weird BIOS related
glitch on Samsung n130 as reported in bko#14314.
http://bugzilla.kernel.org/show_bug.cgi?id=14314
* piix_base_ops dropped as suggested by Sergei.
* Spurious IRQ detection doesn't kick in anymore if polling qc is in
progress. This provides less protection but some controllers have
possible data corruption issues if the wrong register is accessed
while a command is in progress.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Johannes Stezenbach <js@sig21.net>
Reported-by: Hans Werner <hwerner4@gmx.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
host->ports[i] is never NULL if i < host->n_ports and non-NULL return
from ata_qc_from_tag() guarantees that the returned qc is active.
Drop unnecessary tests.
Superflous () dropped as suggested by Sergei.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
flush_dcache_page() must be called after (!ATA_TFLAG_WRITE) the
data copying to avoid D-cache aliasing with user space or I-D cache
coherency issues (when reading data from an ATA device using PIO,
the kernel dirties the D-cache but there is no flush_dcache_page()
required on Harvard architectures).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When we drain data from a device to clear DRQ during error recovery,
the number of bytes reported as drained is too low by a factor of 2
because the count is actually reporting the number of words drained,
not bytes. Fix this.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In libata-sff, ata_sff_post_internal_cmd() directly calls ata_bmdma_stop()
instead of ap->ops->bmdma_stop(). This can be a problem for controllers
that use their own bmdma_stop for which the generic sff one isn't suitable
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Handling of the trailing byte in ata_sff_data_xfer() is suboptimal bacause:
- it always initializes the padding buffer to 0 which is not really needed in
both the read and write cases;
- it has to use memcpy() to transfer a single byte from/to the padding buffer;
- it uses io{read|write}16() accessors which swap bytes on the big endian CPUs
and so have to additionally convert the data from/to the little endian format
instead of using io{read|write}16_rep() accessors which are not supposed to
change the byte ordering.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The legacy old IDE ioctl API for this is a bit primitive so we try
and map stuff sensibly onto it.
- Set PIO over DMA devices to report 32bit
- Add ability to change the PIO32 settings if the controller permits it
- Add that functionality into the sff drivers
- Add that functionality into the VLB legacy driver
- Turn on the 32bit PIO on the ninja32 and add support there
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On a timeout call a device specific handler early in the recovery so that
we can complete and process successful commands which timed out due to IRQ
loss or the like rather more elegantly.
[Revised to exclude the timeout handling on a few devices that inherit from
SFF but are not SFF enough to use the default timeout handler]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
If the device is signalling that there is data to drain after an error we
should read the bytes out and throw them away. Without this some devices
and controllers get wedged and don't recover.
Based on earlier work by Mark Lord
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata keeps a shadow copy of the ATA CTL register (which is write only),
and only writes to the hardware when the required value doesn't match
the shadow. However this copy wasn't being maintained when performing
reset functions. This could cause problems for the first operation after
a reset when the correct value might not be written to the CTL register.
This problem was observed when hotplugging a drive: the identify command
was being issued with interrupts enabled, when they should have been
disabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 871af1210f (libata: Add 32bit
PIO support) has caused all kinds of errors on the ATAPI devices, so
it has been empirically proven that one shouldn't try to read/write
an extra data word when a device is not expecting it already. "Don't
do it then"; however, still use a chance to do 32-bit read/write one
last time when there are exactly 3 trailing bytes.
Oh, and stop pointlessly swapping the bytes to and fro on big-endian
machines by using io*_rep() accessors which shouldn't byte-swap.
This patch should fix the kernel.org bug #12609.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Asus Pundit-R with atiixp controller has the second port missing and,
very unusually, its status is stuck at 0x7f and all others at 0. This
meanst that it fails TF access test but gets detected as a disk due to
classification code check and then evades polling IDENTIFY presence
detection thanks to the missing BSY in the status value causing
excessive delays during boot.
This patch makes libata-sff HSM set NODEV_HINT if the status is 0x7f
to make polling IDENTIFY presence detection work for these machines.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The EH message for NODEV_HINT path was describing the opposite
condition. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes a wrong WARN_ON that was triggered by 32bit PIO support:
WARNING: at drivers/ata/libata-sff.c:1017 ata_sff_hsm_move+0x45e/0x750()
__atapi_pio_bytes simply doesnt know enough to decide if there is a bug.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Convert WARN_ON() on command issue/completion paths to WARN_ON_ONCE()
so that libata doesn't spam the machine even when one of those
conditions triggers repeatedly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This matters for some controllers and in one or two cases almost doubles
PIO performance. Add a bmdma32 operations set we can inherit and activate
it for some controllers
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently libata uses four methods to detect device presence.
1. PHY status if available.
2. TF register R/W test (only promotes presence, never demotes)
3. device signature after reset
4. IDENTIFY failure detection in SFF state machine
Combination of the above works well in most cases but recently there
have been a few reports where a phantom device causes unnecessary
delay during probe. In both cases, PHY status wasn't available. In
one case, it passed #2 and #3 and failed IDENTIFY with ATA_ERR which
didn't qualify as #4. The other failed #2 but as it passed #3 and #4,
it still caused failure.
In both cases, phantom device reported diagnostic failure, so these
cases can be safely worked around by considering any !ATA_DRQ IDENTIFY
failure as NODEV_HINT if diagnostic failure is set.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_sff_post_internal_cmd() needs to grab port lock before calling
ata_bmdma_stop() and also need to clear hsm_task_state. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On HSM_ST_ERR, ata_hsm_move() triggers WARN_ON() if AC_ERR_DEV or
AC_ERR_HSM is not set. PHY events may trigger HSM_ST_ERR with other
error codes and, with or without it, there just isn't much reason to
do WARN_ON() on it. Even if error code is not set there, core EH
logic won't have any problem dealing with the error condition.
OSDL bz#11065 reports this problem.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata has been using mix of jiffies and msecs for time druations.
This is getting confusing. As writing sub HZ values in jiffies is
PITA and msecs_to_jiffies() can't be used as initializer, unify unit
for all time durations to msecs. So, durations are in msecs and
deadlines are in jiffies. ata_deadline() is added to compute deadline
from a start time and duration in msecs.
While at it, drop now superflous _msec suffix from arguments and
rename @timeout to @deadline if it represents a fixed point in time
rather than duration.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Improve SFF HSM violation reporting such that each HSM violation can
be distinguished using ehi_desc.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix G5 SATA irq 18: nobody cared, reported on -rc5 by Olaf Hering:
fixlet to a57c1bade5 libata-sff:
Fix oops reported in kerneloops.org for pnp devices with no ctl
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Tested-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Make ata_sff_altstatus private so nobody uses it by mistake
- Drop the 400nS delay from it
Add
ata_sff_irq_status - encapsulates the IRQ check logic
This function keeps the existing behaviour for altstatus using devices. I
actually suspect the logic was wrong before the changes but -rc isn't the
time to play with that
ata_sff_sync - ensure writes hit the device
Really we want an io* operation for 'is posted' eg ioisposted(ioaddr) so
that we can fix the nasty delay this causes on most systems.
- ata_sff_pause - 400nS delay
Ensure the command hit the device and delay 400nS
- ata_sff_dma_pause
Ensure the I/O hit the device and enforce an HDMA1:0 transition delay.
Requires altstatus register exists, BUG if not so we don't risk
corruption in MWDMA modes. (UDMA the checksum will save your backside in
theory)
The only other complication then is devices with their own handlers.
rb532 can use dma_pause but scc needs to access its own altstatus
register for internal errata workarounds so directly call the drivers own
altstatus function.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some controllers (jmb and inic162x) use 0x77 and 0x7f to indicate that
the device isn't ready yet. It looks like they use 0xff if device
presence is detected but connection isn't established. 0x77 or 0x7f
after connection is established and use the value from signature FIS
after receiving it.
This patch implements ata_check_ready(), which takes TF status value
and determines whether the port is ready or not considering the above
and other conditions, and use it in @check_ready() functions. This is
safe as both 0x77 and 0x7f aren't valid ready status value even though
they have BSY bit cleared.
This fixes hot plug detection failures which can be triggered with
certain drives if they aren't already spun up when the data connector
is hot plugged.
Tested on sil, sil24, ahci (jmb/ich), piix and inic162x combined with
eight drives from all major vendors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
WARN_ON()'s in ata_hsm_move() was too liberal and got triggerred when
it shouldn't (e.g. hotplug events at the right moment). As the HSM
only deals with device errors and state machine violations, make it
check only against them.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently, SATA softresets should do link onlineness check before
actually performing SRST protocol but it doesn't really belong to
softreset.
This patch moves onlineness check in softreset to ata_eh_reset() and
ata_eh_followup_srst_needed() to clean up code and help future sata_mv
changes which need clear separation between SCR and TF accesses.
sata_fsl is peculiar in that its softreset really isn't softreset but
combination of hardreset and softreset. This patch adds dummy private
->prereset to keep the current behavior but the driver really should
implement separate hard and soft resets and return -EAGAIN from
hardreset if it should be follwed by softreset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that all SFF stuff is separated out of core layer, core layer
doesn't call ops->tf_read directly. It gets called only via
ops->qc_fill_rtf() for non-SFF drivers. This patch directly
implements private ops->qc_fill_rtf() for non-SFF controllers and kill
ops->tf_read().
This is much cleaner for non-SFF controllers as some of them have to
cache SFF register values in private data structure and report the
cached values via ops->tf_read(). Also, ops->tf_read() gets nasty for
controllers which don't have clear notion of TF registers when
operation is not in progress.
As this change makes default ops->qc_fill_rtf unnecessary, move
ata_sff_qc_fill_rtf() form ata_base_port_ops to ata_sff_port_ops where
it belongs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
On command completion, ata_qc_complete() directly called ops->tf_read
to fill qc->result_tf. This patch adds ops->qc_fill_rtf to replace
hardcoded ops->tf_read usage.
ata_sff_qc_fill_rtf() which uses ops->tf_read to fill result_tf is
implemented and set in ata_base_port_ops and other ops tables which
don't inherit from ata_base_port_ops, so this patch doesn't introduce
any behavior change.
ops->qc_fill_rtf() is similar to ops->sff_tf_read() but can only be
called when a command finishes. As some non-SFF controllers don't
have TF registers defined unless they're associated with in-flight
commands, this limited operation makes life easier for those drivers
and help lifting SFF assumptions from libata core layer.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Previously, there were two ways to trigger follow-up SRST from
hardreset method - returning -EAGAIN and leaving all device classes
unmodified. Drivers never used the latter mechanism and the only use
case for the former was when hardreset couldn't classify.
Drop the latter mechanism and let -EAGAIN mean "perform follow-up SRST
if classification is required". This change removes unnecessary
follow-up SRSTs and simplifies reset implementations.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Implement sata_std_hardreset(), which simply wraps around
sata_link_hardreset(). sata_std_hardreset() becomes new standard
hardreset method for sata_port_ops and sata_sff_hardreset() moves from
ata_base_port_ops to ata_sff_port_ops, which is where it really
belongs.
ata_is_builtin_hardreset() is added so that both
ata_std_error_handler() and ata_sff_error_handler() skip both builtin
hardresets if SCR isn't accessible.
piix_sidpr_hardreset() in ata_piix.c is identical to
sata_std_hardreset() in functionality and got replaced with the
standard function.
Signed-off-by: Tejun Heo <htejun@gmail.com>
sata_sff_hardreset() contains link readiness wait logic which isn't
SFF specific. Move that part into sata_link_hardreset(), which now
takes two more parameters - @online and @check_ready. Both are
optional. The former is out parameter for link onlineness after
reset. The latter is used to wait for link readiness after hardreset.
Users of sata_link_hardreset() is updated to use new funtionality and
ahci_hardreset() is updated to use sata_link_hardreset() instead of
sata_sff_hardreset(). This doesn't really cause any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Factor out waiting logic (which is common to all ATA controllers) from
ata_sff_wait_ready() into ata_wait_ready(). ata_wait_ready() takes
@check_ready function pointer and uses it to poll for readiness. This
allows non-SFF controllers to use ata_wait_ready() to wait for link
readiness.
This patch also implements ata_wait_after_reset() - generic version of
ata_sff_wait_after_reset() - using ata_wait_ready().
ata_sff_wait_ready() is reimplemented using ata_wait_ready() and
ata_sff_check_ready(). Functionality remains the same.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Previously, post-softreset readiness is waited as follows.
1. ata_sff_wait_after_reset() waits for 150ms and then for
ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.
2. ata_bus_softreset() finishes with -ENODEV if status is still 0xff.
If not, continue to #3.
3. ata_bus_post_reset() waits readiness of dev0 and/or dev1 depending
on devmask using ata_sff_wait_ready().
And for post-hardreset readiness,
1. ata_sff_wait_after_reset() waits for 150ms and then for
ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.
2. sata_sff_hardreset waits for device readiness using
ata_sff_wait_ready().
This patch merges and unifies post-reset readiness waits into
ata_sff_wait_ready() and ata_sff_wait_after_reset().
ATA_TMOUT_FF_WAIT handling is merged into ata_sff_wait_ready(). If TF
status is 0xff, link status is unknown and the port is SATA, it will
continue polling till ATA_TMOUT_FF_WAIT.
ata_sff_wait_after_reset() is updated to perform the following steps.
1. waits for 150ms.
2. waits for dev0 readiness using ata_sff_wait_ready(). Note that
this is done regardless of devmask, as ata_sff_wait_ready() handles
0xff status correctly, this preserves the original behavior except
that it may wait longer after softreset if link is online but
status is 0xff. This behavior change is very unlikely to cause any
actual difference and is intended. It brings softreset behavior to
that of hardreset.
3. waits for dev1 readiness just the same way ata_bus_post_reset() did.
Now both soft and hard resets call ata_sff_wait_after_reset() after
reset to wait for readiness after resets. As
ata_sff_wait_after_reset() contains calls to ->sff_dev_select(),
explicit call near the end of sata_sff_hardreset() is removed.
This change makes reset implementation simpler and more consistent.
While at it, make the magical 150ms wait post-reset wait duration a
constant and ata_sff_wait_ready() and ata_sff_wait_after_reset() take
@link instead of @ap. This is to make them consistent with other
reset helpers and ease core changes.
pata_scc is updated accordingly.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Separate out generic ATA portion from ata_sff_postreset() into
ata_std_postreset() and implement ata_sff_postreset() using the std
version.
ata_base_port_ops now has ata_std_postreset() for its postreset and
ata_sff_port_ops overrides it to ata_sff_postreset().
This change affects pdc_adma, ahci, sata_fsl and sata_sil24. pdc_adma
now specifies postreset to ata_sff_postreset() explicitly. sata_fsl
and sata_sil24 now use ata_std_postreset() which makes no difference
to them. ahci now calls ata_std_postreset() from its own postreset
method, which causes no behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Separate out generic ATA portion from ata_sff_prereset() into
ata_std_prereset() and implement ata_sff_prereset() using the std
version. Waiting for device readiness is the only SFF specific part.
ata_base_port_ops now has ata_std_prereset() for its prereset and
ata_sff_port_ops overrides it to ata_sff_prereset(). This change can
affect pdc_adma, ahci, sata_fsl and sata_sil24. pdc_adma implements
its own prereset using ata_sff_prereset() and the rest has hardreset
and thus are unaffected by this change.
This change reflects real world situation. There is no generic way to
wait for device readiness for non-SFF controllers and some of them
don't have any mechanism for that. Non-sff drivers which don't have
hardreset should wrap ata_std_prereset() and wait for device readiness
itself but there's no such driver now and isn't likely to be popular
in the future either.
Signed-off-by: Tejun Heo <htejun@gmail.com>
->sff_irq_clear() is called only from SFF interrupt handler, so there
is no reason to initialize it for non-SFF controllers. Also,
ata_sff_irq_clear() can handle both BMDMA and non-BMDMA SFF
controllers.
This patch kills ata_noop_irq_clear() and removes it from base
port_ops and sets ->sff_irq_clear to ata_sff_irq_clear() in sff
port_ops instead of bmdma port_ops.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Add sff_ prefix to SFF specific port ops.
This rename is in preparation of separating SFF support out of libata
core layer. This patch strictly renames ops and doesn't introduce any
behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
SFF functions have confusing names. Some have sff prefix, some have
bmdma, some std, some pci and some none. Unify the naming by...
* SFF functions which are common to both BMDMA and non-BMDMA are
prefixed with ata_sff_.
* SFF functions which are specific to BMDMA are prefixed with
ata_bmdma_.
* SFF functions which are specific to PCI but apply to both BMDMA and
non-BMDMA are prefixed with ata_pci_sff_.
* SFF functions which are specific to PCI and BMDMA are prefixed with
ata_pci_bmdma_.
* Drop generic prefixes from LLD specific routines. For example,
bfin_std_dev_select -> bfin_dev_select.
The following renames are noteworthy.
ata_qc_issue_prot() -> ata_sff_qc_issue()
ata_pci_default_filter() -> ata_bmdma_mode_filter()
ata_dev_try_classify() -> ata_sff_dev_classify()
This rename is in preparation of separating SFF support out of libata
core layer. This patch strictly renames functions and doesn't
introduce any behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
pdc_adma has interface similar to SFF but has its own DMA interface.
It currently implements noop bmdma ops to avoid crashing
ata_bmdma_error_handler() which BTW actually is EH for SFF drivers.
This patch makes ata_bmdma_error_handler() dereference bmdma ops iff
bmdma_addr is initialized as done in ata_bmdma_post_internal_cmd.
This change allows pdc_adma to standardize ops and use SFF
error_handler and post_internal_cmd.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_chk_status() just calls ops->check_status and it only adds
confusion with other status functions. Kill it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_pci_default_filter() doesn't really have anything to do with PCI.
It's generally applicable to BMDMA controllers. Move it out of
CONFIG_PCI.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Move SFF related functions from libata-core.c to libata-sff.c.
ata_[bmdma_]sff_port_ops, ata_devchk(), ata_dev_try_classify(),
ata_std_dev_select(), ata_tf_to_host(), ata_busy_sleep(),
ata_wait_after_reset(), ata_wait_ready(), ata_bus_post_reset(),
ata_bus_softreset(), ata_bus_reset(), ata_std_softreset(),
sata_std_hardreset(), ata_fill_sg(), ata_fill_sg_dumb(),
ata_qc_prep(), ata_dump_qc_prep(), ata_data_xfer(),
ata_data_xfer_noirq(), ata_pio_sector(), ata_pio_sectors(),
atapi_send_cdb(), __atapi_pio_bytes(), atapi_pio_bytes(),
ata_hsm_ok_in_wq(), ata_hsm_qc_complete(), ata_hsm_move(),
ata_pio_task(), ata_qc_issue_prot(), ata_host_intr(),
ata_interrupt(), ata_std_ports()
* Make ata_pio_queue_task() global as it's now called from
libata-sff.c.
* Move SFF related stuff in include/linux/libata.h and
drivers/ata/libata.h into one place. While at it, move timing
constants into the global enum definition and fortify comments a
bit.
This patch strictly moves stuff around and as such doesn't cause any
functional difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reorder functions in drivers/ata/libata-sff.c such that functions
generally follow ops table order and init functions come last. This
is in preparation of SFF cleanup.
This patch strictly moves stuff around and as such doesn't cause any
functional difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently reset methods are not specified directly in the
ata_port_operations table. If a LLD wants to use custom reset
methods, it should construct and use a error_handler which uses those
reset methods. It's done this way for two reasons.
First, the ops table already contained too many methods and adding
four more of them would noticeably increase the amount of necessary
boilerplate code all over low level drivers.
Second, as ->error_handler uses those reset methods, it can get
confusing. ie. By overriding ->error_handler, those reset ops can be
made useless making layering a bit hazy.
Now that ops table uses inheritance, the first problem doesn't exist
anymore. The second isn't completely solved but is relieved by
providing default values - most drivers can just override what it has
implemented and don't have to concern itself about higher level
callbacks. In fact, there currently is no driver which actually
modifies error handling behavior. Drivers which override
->error_handler just wraps the standard error handler only to prepare
the controller for EH. I don't think making ops layering strict has
any noticeable benefit.
This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and
their PMP counterparts propoer ops. Default ops are provided in the
base ops tables and drivers are converted to override individual reset
methods instead of creating custom error_handler.
* ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs
aren't accessible. sata_promise doesn't need to use separate
error_handlers for PATA and SATA anymore.
* softreset is broken for sata_inic162x and sata_sx4. As libata now
always prefers hardreset, this doesn't really matter but the ops are
forced to NULL using ATA_OP_NULL for documentation purpose.
* pata_hpt374 needs to use different prereset for the first and second
PCI functions. This used to be done by branching from
hpt374_error_handler(). The proper way to do this is to use
separate ops and port_info tables for each function. Converted.
Signed-off-by: Tejun Heo <htejun@gmail.com>
port_info->private_data is currently used for two purposes - to record
private data about the port_info or to specify host->private_data to
use when allocating ata_host.
This overloading is confusing and counter-intuitive in that
port_info->private_data becomes host->private_data instead of
port->private_data. In addition, port_info and host don't correspond
to each other 1-to-1. Currently, the first non-NULL
port_info->private_data is used.
This patch makes port_info->private_data just be what it is -
private_data for the port_info where LLD can jot down extra info.
libata no longer sets host->private_data to the first non-NULL
port_info->private_data, @host_priv argument is added to
ata_pci_init_one() instead. LLDs which use ata_pci_init_one() can use
this argument to pass in pointer to host private data. LLDs which
don't should use init-register model anyway and can initialize
host->private_data directly.
Adding @host_priv instead of using init-register model for LLDs which
use ata_pci_init_one() is suggested by Alan Cox.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
ata_pci_init_one() is the only function which uses ops->irq_handler
and pi->sht. Other initialization functions take the same information
as arguments. This causes confusion and duplicate unused entries in
structures.
Make ata_pci_init_one() take sht as an argument and use ata_interrupt
implicitly. All current users use ata_interrupt and if different irq
handler is necessary open coding ata_pci_init_one() using
ata_prepare_sff_host() and ata_activate_sff_host can be done under ten
lines including error handling and driver which requires custom
interrupt handler is likely to require custom initialization anyway.
As ata_pci_init_one() was the last user of ops->irq_handler, this
patch also kills the field.
Signed-off-by: Tejun Heo <htejun@gmail.com>
->irq_clear() is used to clear IRQ bit of a SFF controller and isn't
useful for drivers which don't use libata SFF HSM implementation.
However, it's a required callback and many drivers implement their own
noop version as placeholder. This patch implements ata_noop_irq_clear
and use it to replace those custom placeholders.
Also, SFF drivers which don't support BMDMA don't need to use
ata_bmdma_irq_clear(). It becomes noop if BMDMA address isn't
initialized. Convert them to use ata_noop_irq_clear().
Signed-off-by: Tejun Heo <htejun@gmail.com>
SFF incorrectly assumed that ctl register is available for all
controllers while some old SFF controllers don't have ctl register.
Make SFF handle controllers w/o ctl register by conditionalizing ctl
register access and softreset method.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Factor out ata_pci_activate_sff_host() from ata_pci_one(). This does
about the same thing as ata_host_activate() but needs to be separate
because SFF controllers use different and multiple IRQs in legacy
mode.
This will be used to make SFF LLD initialization more flexible.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata-sff code used DRV_NAME which is hardcoded to "libata" when
requesting resources. Use dev_driver_string() such that low level
driver names are used in resource listing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_PROT_ATAPI_* are ugly and naming schemes between ATA_PROT_* and
ATA_PROT_ATAPI_* are inconsistent causing confusion. Rename them to
ATAPI_PROT_* and make them consistent with ATA counterpart.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jeff said he preferred that the SFF tf_load followed the spec and we
documented that anyone who needed different overrode it, rather than it
using the ->check_status methods. No driver relies on the current behaviour.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It is legitimate (although annoying and silly) for a PCI IDE controller
not to be assigned an interrupt and to be polled. The libata-sff code
should therefore not try and request IRQ 0 in this case.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tackle the relatively sane complaints of checkpatch --file.
The vast majority is indentation and whitespace changes, the rest are
* #include fixes
* printk KERN_xxx prefix addition
* BSS/initializer cleanups
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] kill ata_sg_is_last()
Update libata driver for bf548 atapi controller against the 2.6.24 tree.
libata-sff: Correct use of check_status()
drivers/ata: add support to Freescale 3.0Gbps SATA Controller
pata_acpi: fix build breakage if !CONFIG_PM
Get rid of sparse related warnings from places that use integer as NULL
pointer.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ata_check_status() does an SFF compliant check
ata_chk_status() does a generic call to ap->ops->check_status (usually
ata_check_status)
libata-sff uses the wrong one. Hardly suprising given the naming here,
which ought to get fixed to ata_sff_check_status() perhaps ?
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently, port configuration reporting has the following problems.
* iomapped address is reported instead of raw address
* report contains irrelevant fields or lacks necessary fields for
non-SFF controllers.
* host->irq/irq2 are there just for reporting and hacky.
This patch implements and uses ata_port_desc() and
ata_port_pbar_desc(). ata_port_desc() is almost identical to
ata_ehi_push_desc() except that it takes @ap instead of @ehi, has no
locking requirement, can only be used during host initialization and "
" is used as separator instead of ", ". ata_port_pbar_desc() is a
helper to ease reporting of a PCI BAR or an offsetted address into it.
LLD pushes whatever description it wants using the above two
functions. The accumulated description is printed on host
registration after "[S/P]ATA max MAX_XFERMODE ".
SFF init helpers and ata_host_activate() automatically add
descriptions for addresses and irq respectively, so only LLDs which
isn't standard SFF need to add custom descriptions. In many cases,
such controllers need to report different things anyway.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* ->irq_ack() is redundant to what the irq handler already
performs... chk-status + irq-clear. Furthermore, it is only
called in one place, when screaming-irq-debugging is enabled,
so we don't want to bother with a hook just for that.
* ata_dummy_irq_on() is only ever used in drivers that have
no callpath reaching ->irq_on(). Remove .irq_on hook from
those drivers, and the now-unused ata_dummy_irq_on()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the following PHY-related functions to deal with ata_link instead
of ata_port.
* sata_print_link_status()
* sata_down_spd_limit()
* ata_set_sata_spd_limit() and friends
* sata_link_debounce/resume()
* sata_scr_valid/read/write/write_flush()
* ata_link_on/offline()
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Introduce ata_link. It abstracts PHY and sits between ata_port and
ata_device. This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port. Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.
This patch only defines the host link. Multiple link handling will be
added later. Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code moved to ioread/iowrite but the comment didn't
Also note a posting issue
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Seems nobody else is checking/testing this case as it keeps getting
horked.
If we have no BAR4 mapping on an SFF controller this is *NOT* an error,
it just means it isn't doing BMDMA.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_tf_read was setting HOB bit when lba48 command was submitted, but
was not clearing it before reading "normal" data. As it is only place
which sets HOB bit in control register, and register reads should not
be affected by other bits, let's just clear it when we are done with
reading upper bytes so non-48bit commands do not have to touch ctl
at all.
pata_scc suffered from same problem...
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With PCI resource fix up for legacy hosts. We can use the same code
path to allocate IO resources and initialize host for both legacy and
native SFF hosts. Only IRQ requesting needs to be different.
Rename ata_pci_*_native_host() to ata_pci_*_sff_host(), kill all
legacy specific functions and use the renamed functions instead. This
simplifies code a lot.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
host->irq and host->irq2 should be set before ata_host_register() for
IRQ reporting to work. Move up host->irq assignment in
ata_host_activate() and add it to ata_pci_init_one() native path and
pata_cs5520.
The port info printing in ata_host_register() doesn't fit all the
different controllers. It should probably be moved out to LLDs with
some helpers in the future.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ata IRQ ack functions are only used when debugging. Unfortunately
almost every controller that calls them can cause crashes in some
configurations as there are missing checks for bmdma presence.
In addition ata_port_start insists of installing DMA buffers and pad
buffers for controllers regardless. The SFF controllers actually need to
make that decision dynamically at controller setup time and all need the
same helper - so we add ata_sff_port_start. Future patches will switch
the SFF drivers to use this.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The intention of using port_mask in SFF init helpers was to eventually
support exoctic configurations such as combination of legacy and
native port on the same controller. This never became actually
necessary and the related code always has been subtly broken one way
or the other. Now that new init model is in place, there is no reason
to make common helpers capable of handling all corner cases. Exotic
cases can simply dealt within LLDs as necessary.
This patch removes port_mask handling in SFF init helpers. SFF init
helpers don't take n_ports argument and interpret it into port_mask
anymore. All information is carried via port_info. n_ports argument
is dropped and always two ports are allocated. LLD can tell SFF to
skip certain port by marking it dummy. Note that SFF code has been
treating unuvailable ports this way for a long time until recent
breakage fix from Linus and is consistent with how other drivers
handle with unavailable ports.
This fixes 1-port legacy host handling still broken after the recent
native mode fix and simplifies SFF init logic. The following changes
are made...
* ata_pci_init_native_host() and ata_init_legacy_host() both now try
to initialized whatever they can and mark failed ports dummy. They
return 0 if any port is successfully initialized.
* ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't
take n_ports argument. All info should be specified via port_info
array. Always two ports are allocated.
* ata_pci_init_bmdma() exported to be used by LLDs in exotic cases.
* port_info handling in all LLDs are standardized - all port_info
arrays are const stack variable named ppi. Unless the second port
is different from the first, its port_info is specified as NULL
(tells libata that it's identical to the last non-NULL port_info).
* pata_hpt37x/hpt3x2n: don't modify static variable directly. Make an
on-stack copy instead as ata_piix does.
* pata_uli: It has 4 ports instead of 2. Don't use
ata_pci_prepare_native_host(). Allocate the host explicitly and use
init helpers. It's simple enough.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Marvell IDE interface on my machine would hit a BUG_ON() in
lib/iomem.c because it was calling ata_pci_init_one() specifying just a
single port on the host, but that would actually end up trying to
initialize two ports, the second one with bogus information.
This fixes "ata_pci_init_one()" so that it actually passes down the
n_ports variable that it got from the low-level driver to the host
allocation routine ("ata_host_alloc_pinfo()"), which results in the ATA
layer actually having the correct port number information.
And in order to make it all work, I also needed to fix a few places that
had incorrectly hard-coded the fact that a host always had exactly two
ports (both ata_pci_init_bmdma() and ata_request_legacy_irqs() would
just always iterate over both ports).
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All drivers are converted to new init model. Kill probe_ent,
ata_device_add() and ata_pci_init_native_mode().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These will be used to convert LLDs to new init model.
* Add irq_handler field to port_info. In new init model, requesting
IRQ is LLD's responsibility and libata doesn't need to know about
irq_handler. Most LLDs can simply register their irq_handler but
some need different irq_handler depending on specific chip. The
added port_info->irq_handler field can be used by LLDs to select
the matching IRQ handler in such cases.
* Add ata_dummy_port_info.
* Implement ata_pci_prepare_native_host(), a helper to alloc ATA host,
acquire all resources and init the host in one go.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert native PCI host handling to alloc-init-register model. New
function ata_pci_init_native_host() follows the new init model and
replaces ata_pci_init_native_mode(). As there are remaining LLD
users, the old function isn't removed yet.
ata_pci_init_one() is reimplemented using the new function and now
fully converted to new init model.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert legacy PCI host handling to alloc-init-register model.
ata_init_legacy_host(), ata_request_legacy_irqs() and
ata_pci_init_bmdma() are separated out and follow the new init model.
The two legacy handling functions use separate ata_legacy_devres
instead of generic devm_* resources. This reduces devres overhead for
legacy hosts which was a bit high because it didn't use PCI/iomap
merged resoruces.
ata_pci_init_one() is rewritten in terms of the aboved functions but
native mode handling is still using the old method. Conversion will
be completed when native mode handling is updated.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Disabled port handling in ata_pci_init_native_mode() is slightly
broken in that it may end up using the wrong port_info. This patch
updates it such that disables ports are made dummy as done in the
legacy and other cases.
While at it, fix indentation in ata_resources_present().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Both old-IDE and libata should be able handle all controllers and
devices found using normal resource reservation methods.
This eliminates the awful, low-performing split-driver configuration
where old-IDE drove the PATA portion of a PCI device, in PIO-only mode,
and libata drove the SATA portion of the /same/ PCI device, in DMA mode.
Typically vendors would ship SATA hard drive / PATA optical
configuration, which would lend itself to slow (PIO-only) CD-ROM
performance.
For Intel users running in combined mode, it is now wholly dependent on
your driver choice (potentially link order, if you compile both drivers
in) whether old-IDE or libata will drive your hardware.
In either case, you will get full performance from both SATA and PATA
ports now, without having to pass a kernel command line parameter.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With Tejun having added adev->ap some time ago we can get rid of the
almost unused port being passed to mode filters. And while we are
doing filters, lets turn on the !IORDY filter as well.
Signed-off-by: Alan Cox <alan@redhat.com>
With some hand massaging from
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_port has two different id fields - id and port_no. id is
system-wide 1-based unique id for the port while port_no is 0-based
host-wide port number. The former is primarily used to identify the
ATA port to the user in printk messages while the latter is used in
various places in libata core and LLDs to index the port inside the
host.
The two fields feel quite similar and sometimes ap->id is used in
place of ap->port_no, which is very difficult to spot. This patch
renames ap->id to ap->print_id to reduce the possibility of such bugs.
Some printk messages are adjusted such that id string (ata%u[.%u])
isn't printed twice and/or to use ata_*_printk() instead of hardcoded
id format.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch is against the libata core and headers.
Two IRQ calls are added in ata_port_operations.
- irq_on() is used to enable interrupts.
- irq_ack() is used to acknowledge a device interrupt.
In most drivers, ata_irq_on() and ata_irq_ack() are used for
irq_on and irq_ack respectively.
In some drivers (ex: ahci, sata_sil24) which cannot use them
as is, ata_dummy_irq_on() and ata_dummy_irq_ack() are used.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert libata core layer and LLDs to use iomap.
* managed iomap is used. Pointer to pcim_iomap_table() is cached at
host->iomap and used through out LLDs. This basically replaces
host->mmio_base.
* if possible, pcim_iomap_regions() is used
Most iomap operation conversions are taken from Jeff Garzik
<jgarzik@pobox.com>'s iomap branch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo