Commit Graph

111674 Commits

Author SHA1 Message Date
Vivek Natarajan a6ef530f2b ath9k_hw: Add support for btcoexistence in AR9300.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-28 14:50:01 -04:00
Vivek Natarajan 978f78bf71 ath9k_hw: Move bt_stomp to hw from common.
Move bt_stomp to ath9k_hw and add its support for latest chipsets.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-28 14:50:00 -04:00
Larry Finger d3bb1429a2 rtlwifi: rtl8192ce: rtl8192cu: Fix most sparse warnings
Fix most sparse warnings in rtlwifi, rtl8192ce and rtl8192cu drivers.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 16:14:55 -04:00
Chaoming_Li 76c34f910a rtlwifi: rtl8192ce: Change rtl8192ce routines phy and trx and modify rtl8192cu for addition of rtl8192se and rtl8192de
Change rtl8192ce routines phy and trx for addition of RTL8192SE and RTL8192DE.
In addition, make necessary modifications to rtl8192cu. This patch also
removes the temporary patches needed to enable intermediate steps to build
without error.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 16:14:55 -04:00
Chaoming_Li e0b5a50786 rtlwifi: rtl8192ce: Change phy and rc routines for addition of rtl8192se and rtl8192de
Change rtl8192ce routines phy and rc for addition of RTL8192SE and
RTL8192DE.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 16:14:55 -04:00
Chaoming_Li 2b8359f85b rtlwifi: rtl8192ce: Change sw and LED routines for addition of rtl8192se and rtl8192de
Change rtl8192ce sw and LED routines for addition of RTL8192SE and
RTL8192DE.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 16:14:55 -04:00
Chaoming_Li f73b279cdb rtlwifi: rtl8192ce: Change hw routine for addition of rtl8192se and rtl8192de
Change rtl8192ce hw routine for addition of RTL8192SE and RTL8192DE.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 16:13:33 -04:00
Chaoming_Li c07ccff326 rtlwifi: rtl8192c-common: Change common PHY routines for addition of rtl8192se and rtl8192de
Change common PHY routines for addition of RTL8192SE and RTL8192DE code.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 16:13:33 -04:00
Chaoming_Li 3ac5e26a1e rtlwifi: rtl8192c-common: Change common firmware routines for addition of rtl8192se and rtl8192de
Change common firmware routines for addition of RTL8192SE and
RTL8192DE code.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 16:13:33 -04:00
Chaoming_Li beb5bc4020 rtlwifi: rtl8192c-common: Convert common dynamic management routines for addition of rtl8192se and rtl8192de
Convert common dynamic management routines for addition of RTL8192SE
and RTL8192DE code.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 16:13:33 -04:00
Chaoming_Li d93cdee975 rtlwifi: Convert usb routines for addition of rtl8192se and rtl8192de
Convert usb routines for addition of RTL8192SE and RTL8192DE code

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 16:13:32 -04:00
Chaoming_Li 81b2904511 rtlwifi: Convert regulatory domain routines for addition of rtl8192se and rtl8192de
Convert regulatory domain  routines for addition of RTL8192SE and
RTL8192DE code.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 16:13:32 -04:00
Chaoming_Li c6a9de0823 rtlwifi: Convert rc routines for addition of rtl8192se and rtl8192de
Convert rc routines for addition of RTL8192SE and RTL8192DE code

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 16:13:32 -04:00
Chaoming_Li cc7dc0c4ff rtlwifi: Convert ps routines for addition of rtl8192se and rtl8192de
Convert ps routines for addition of RTL8192SE and RTL8192DE code

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 16:13:32 -04:00
Chaoming_Li c7cfe38ee0 rtlwifi: Convert pci routines for addition of rtl8192se and rtl8192de
Convert pci routines for addition of RTL8192SE and RTL8192DE code
These changes allow the upper-level driver to specify the BAR to be
used as it is different for rtl8192se than for the others.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 16:13:32 -04:00
Chaoming_Li 0baa0fd76f rtlwifi: Convert core routines for addition of rtl8192se and rtl8192de
Convert core routines for addition of RTL8192SE and RTL8192DE code.

Additional files are changed to allow compilation.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 16:13:32 -04:00
Chaoming_Li 46a6272c20 rtlwifi: Change cam routines for addition of rtl8192se and rtl8192de
Change cam routines for addition of RTL8192SE and RTL8192DE code

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 16:13:31 -04:00
Chaoming_Li acd48572c3 rtlwifi: Change base routines for addition of rtl8192se and rtl8192de
Change base routines for addition of RTL8192SE and RTL8192DE code.

Additional files are modified to allow compilation.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 16:13:31 -04:00
Chaoming_Li 3dad618b7b rtlwifi: Change wifi.h for rtl8192se and rtl8192de
Change wifi.h for addition of RTL8192SE and RTL8192DE code

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 16:13:31 -04:00
Chaoming_Li e25f51d4f9 rtlwifi: Change efuse routines addition of RTL8192SE and RTL8192DE
Change efuse routines for addition of RTL8192SE and RTL8192DE code

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 16:13:31 -04:00
Christian Lamparter caf1eae206 carl9170: improve unicast PS buffering
Using the ieee80211_sta_block allows the PS code
to handle awake->doze->awake transitions of our
clients in a race-free manner.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 15:50:30 -04:00
Christian Lamparter be8d98eab8 p54: implement multicast filter
"For best CPU usage and power consumption, having as few
frames as possible percolate through the stack is
desirable. Hence, the hardware should filter as much
as possible."

Note: Not all firmwares include the multicast filter
feature and the stack does not filter them either.
The ARP filter on the other hand was dropped from the
patch since it does not work correctly:

Quote from: Max Filippov <jcmvbkbc@gmail.com>
<http://www.spinics.net/lists/linux-wireless/msg67466.html>
"In the ARP case, when there's no other traffic on p54spi,
all ARP requests are dropped. But if there's some egress
traffic from p54spi, filter seems to work correctly:
only ARP requests that match filter pass through.

In the multicast case filter seems to work correctly, but
it treats broadcast as subject to that filtering too. By
default only 01:00:5e:00:00:01 gets into priv->mc_maclist,
so we miss all broadcasts.

These two filters seem to interfere:
- if we set ARP filter and multicast filter without bc
	=>  we miss all ARPs if there's no egress traffic;
- if we set ARP filter and multicast filter with bc or
	don't set mc filter at all => we get all ARPs.

This effect does not depend on filter setup order."

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Tested-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 15:50:30 -04:00
Rafał Miłecki 04ad1fb264 ssb: update reject bit for Target State Low
My 14e4:4315 is SSB_IDLOW_SSBREV_26:
read32 0xfaafcff8 -> 0x600422d5
My 14e4:4328 is SSB_IDLOW_SSBREV_24:
read32 0xfaafcff8 -> 0x400422c5
My 14e4:432b is SSB_IDLOW_SSBREV_26 again:
read32 0xfaafcff8 -> 0x600422d5

For all of them wl driver is using 0x2 reject bit:
write32(0xf98) <- 0x00010002
So it seems SSB 2.3 is the exception using another bit.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 15:50:29 -04:00
Rafał Miłecki a6ef814383 ssb: mark bus as powered up earlier
ssb_chipco_set_clockmode may want to touch CC registers to control power of the
bus. However touching registers without powered_up set causes warnings.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 15:50:29 -04:00
Adrian Chadd 25f63a5a37 ath9k: fix AR9160 xpaBiasLvlFreq endianness handling
The xpaBiasLvlFreq parameter array is made up of 16 bit words which
aren't byte-swapped like the other 16-bit eeprom parameters are.
It's only used by the AR9160.

Signed-off-by: Adrian Chadd <adrian@freebsd.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 15:50:28 -04:00
Rajkumar Manoharan 92c6f76c6d ath9k: set beacon related ps flags on bss_info change
Requesting beacon sync up to configure beacon timers properly
in hw, has be done after doing beacon config with default values.
Setting the flags in beacon config is causing the device to not
enter into network sleep on idle state.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 15:50:28 -04:00
Rajkumar Manoharan 3782c69d6e ath9k_hw: Fix Tx IQ Calibration hang issue in AR9003 chips
On AR9003 chips, doing three IQ calibrations will possibly cause chip
in stuck state. In noisy environment, chip could receive
a packet during the middle of three calibrations and it causes
the conflict of HW access and the eventual failure. It also
causes IQ calibration outliers which results in poor Tx EVM.

The IQ Cal procedure is after resetting the chip, run IQ cal 3 times
per each cal cycle and find the two closest readings and average of two.
The advantage of running Tx IQ cal more than once is that we can compare
calibration results for the same gain setting over multiple iterations.
Most of the cases the IQ failures were observed after first pass.

For the AR9485 and later chips, Tx IQ Calibration is performed along
with AGC cal. But for pre-AR9485 chips, Tx IQ cal HW has to be separated
from the rest of calibration HW to avoid chip hang. After all
calibrations are done in HW, we can start SW post-processing.
By doing this way, we minimize the SW difference among all chips.

The order of calibration (run IQ cal before other calibration) is also
needed to avoid chip hang for chips before AR9485. This issue was
originally observed with AR9382.

During the issue kernel log was filled with following message
ath: timeout (100000 us) on reg 0xa640: 0x00000001 & 0x00000001 != 0x00000000
ath: timeout (100000 us) on reg 0xa2c4: 0x00158dd9 & 0x00000001 != 0x00000000
ath: Unable to reset channel (2412 MHz), reset status -5
ath: Unable to set channel

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-26 15:50:27 -04:00
John W. Linville 429576b97c Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 2011-04-26 15:39:10 -04:00
Rafał Miłecki 9835a30e98 ssb: cc: clear GPIOPULL registers on init
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:20 -04:00
Mohammed Shafi Shajakhan 6dde1aabf6 ath9k: Add TSFOOR interrupt stats in debug info
This helped the developers to fix an issue of chip not entering network
sleep during idle state, previously this was only available as a debug
message

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:20 -04:00
Mohammed Shafi Shajakhan cedc7e3d0c ath9k: remove the unlikely check for autosleep
newer chipsets support auto sleep feature, so remove the
unlikely check which does not seems to help anything

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:19 -04:00
Senthil Balasubramanian b84628eb57 ath9k: Add power save wrappers and modularize hw_pll handler
We should protect hw_pll handler with power save wrappers and
also modularize hw_pll handler properly for better readability.

Also add a debug message to track chip resets on pll hang condition.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:19 -04:00
Senthil Balasubramanian 9eab61c2bf ath9k: cleanup hw pll work handler
There is no reason why pll work handler should be part of xmit
file. move it to main.c so that reading hw check routines are
all in the same place.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:18 -04:00
Senthil Balasubramanian 5151390669 ath9k: optimize the usage of power save wrappers.
We need not wake up the chip even before mutex lock is acquired and also
that it is required only if we are going to drain the txq. So place the
wrappers accordingly and this change is also useful when there are no
pending frames in the txq as we do not wake up the chip unnecessarily.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:18 -04:00
Senthil Balasubramanian d1c038d620 ath9k_hw: Fix incorrect baseband PLL phase shift for AR9485
we should program the AR9485 baseband PLL phase shift to 6 and
a redundant setting overwrites the correct value. Remove the
incorrect and unwnated register setting.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:17 -04:00
Senthil Balasubramanian 353e5019e0 ath9k: Fix LED gpio for AR93xx chipsets.
The LED gpio is incorrectly programmed for AR9300 and so the led
is not working propelry. AR93xx uses gpio 10 for LED and not the
default.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:17 -04:00
Vasanthakumar Thiagarajan 0a6c9b1b66 ath9k: Fix warning: symbol 'ath9k_platform_id_table' was not declared. Should it be static?
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:17 -04:00
Vasanthakumar Thiagarajan 788f6875fc ath9k: Fix bug in configuring hw timer
Hw next tigger time is configured as current_tsf + (timer_period * 10) which
is wrong, it should be current_tsf + timer_period. The wrong hw timer configuration
would cause btcoex related issues.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:16 -04:00
Nishant Sarmukadam 31d291a769 mwl8k: Enable life time expiry for tx packets in the hardware
Tell the firmware to enable the life time expiry of tx packets
in the hardware. The hardware will now refer to the timestamp
in every tx packet and decide whether the packet needs to be
dropped or transmitted.

Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:16 -04:00
Nishant Sarmukadam 3a76988879 mwl8k: Reserve buffers for tx management frames
Since queues are not stopped anymore, management frames would be
dropped if the corresponding tx queue is full.
This can cause issues say when we want to setup an ampdu stream and
action frames i.e addba requests keep getting dropped frequently.
Fix this by reserving some buffers to allow management frames to
go through in queue full conditions.

Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:16 -04:00
Pradeep Nemavat 566875db50 mwl8k: Add timestamp information for tx packets
Timestamp tx packets using a HW micro-second timer.
This timestamp will be compared to the current timestamp
in the hardware and if the difference is greater than 500ms,
the packet will be dropped.

Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:16 -04:00
Pradeep Nemavat 3a7dbc3b2a mwl8k: Do not stop tx queues
This is in preparation to support life time expiry of packets in the
hardware to avoid head-of-line blocking where a slow client can
hog a tx queue and affect the traffic to a faster client from the same
queue. Time stamp the packets in driver to allow dropping them in the
hardware if they are queued for more than 500ms.

If queues are stopped, packets will be queued up outside the driver.
Since we will be able to timestamp the packets only after they hit the
driver, the timestamp will be less accurate since we cannot consider
the time the packets spent in queues outside the driver. With this commit,
to achieve accurate timestamping, the tx queues will not be stopped in
normal conditions. The only scenarios where the queues will be stopped are
when firmware commands are executing or if the interface is brought down.
Now, we need to be prepared for a situation where packets hit the driver
even after the tx queues are full. Drop all such packets in the driver itself.

Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:15 -04:00
Stanislaw Gruszka 2624e96ce1 iwlwifi: fix possible data overwrite in hcmd callback
My commit 3598e1774c
"iwlwifi: fix enqueue hcmd race conditions" move hcmd callback after
command queue reclaim, to avoid call it with hcmd_lock. But since
queue read index was updated, cmd data can be overwritten. Fix problem
by calling callback before taking hcmd_lock and queue reclaim.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:15 -04:00
Sujith Manoharan 767ad6a0a2 ath9k_htc: Remove unused macros and structures
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:15 -04:00
Sujith Manoharan c58ca5b508 ath9k_htc: Use power save wrappers when accessing HW
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:14 -04:00
Sujith Manoharan f0dd49803b ath9k_htc: Fix max A-MPDU size handling
Set the maximum ampdu size of a station correctly
in the target by using the ampdu_factor.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:14 -04:00
Sujith Manoharan 3a0593efd1 ath9k_htc: Fix AMPDU subframe handling
* Register the driver's maximum ampdu subframe limit to mac80211.
* Cleanup the target capabilities structure and fix an endian issue.
* Fix BTCOEX by sending a command to the target when the BT priority
  changes.
* Bump the required firmware version to 1.1

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:14 -04:00
Sujith Manoharan 0ff2b5c05d ath9k: Fix warnings from -Wunused-but-set-variable
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:14 -04:00
Rafał Miłecki 3c35c84a70 ssb: cc: use correct min_msk for 0x4312
Default min_msk on my 0x4312 is 0x80000CBB, not 0xCBB. Now we follow
specs and wl (noticed in MMIO dumps).

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:13 -04:00
Rafał Miłecki 9be1cb39c6 ssb: pci: trivial: correct amount of maximum retries
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:13 -04:00