modified CMD_TIMEOUT and DAT_TIMEOUT to CMD_TIME_OUT and DAT_TIME_OUT
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3719
When the CPLBs get a miss, we do:
- find a victim in the HW table
- remove the victim
- find the replacement in the software table
- put it into the HW table.
If we can't find a replacement in the software table, we accidently
leave a duplicate in the HW table. This patch ensures that duplicate
is marked as not valid.
What we should do is find the replacement in the software table, before
we find a victim in the HW table - but its too late in the release cycle
to do that much restructuring of this code.
Rather that duplicate code, connect Hardware Errors (irq5) into trap_c,
so user space processes get killed properly.
The rest of irq_panic() can be moved into traps.c (later)
There is still a small corner case that causes problems when a
pheriperal interrupt goes off a single cycle before a user space
hardware error. This causes a kernel panic, rather than the user
space process being killed.
But, this checkin makes things work in 99.9% of the cases, and is a vast
improvement from what is there today (which fails 100% of the time).
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
revert 19ef930927.
Kevin Winchester reported a lockup during X startup an bisected
it to this commit.
Reported-by: Kevin Winchester <kjwinchester@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] DFS build fixes
[CIFS] DFS support: provide shrinkable mounts
[CIFS] Do not log path names in lookup errors
[CIFS] DFS support patchset: Added mountdata
[CIFS] Forgot to add two new files from previous commit
[CIFS] DNS name resolution helper upcall for cifs
[CIFS] fix checkpatch warnings in fs/cifs/inode.c
[CIFS] hold ses sem on tcp session reconnect during mount
[CIFS] Allow setting mode via cifs acl
[CIFS] fix unicode string alignment in SPNEGO setup
[CIFS] cifs_partialpagewrite() cleanup
[CIFS] use krb5 session key from first SMB session after a NegProt
[CIFS] redo existing session setup if needed in cifs_mount
[CIFS] Only dump SPNEGO key if CONFIG_CIFS_DEBUG2 is set
[CIFS] fix SetEA failure to some Samba versions
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (63 commits)
ide: remove REQ_TYPE_ATA_CMD
ide: switch ide_cmd_ioctl() to use REQ_TYPE_ATA_TASKFILE requests
ide: switch set_xfer_rate() to use REQ_TYPE_ATA_TASKFILE requests
ide: fix final status check in drive_cmd_intr()
ide: check BUSY and ERROR status bits before reading data in drive_cmd_intr()
ide: don't enable local IRQs for PIO-in in driver_cmd_intr() (take 2)
ide: convert "empty" REQ_TYPE_ATA_CMD requests to use REQ_TYPE_ATA_TASKFILE
ide: initialize rq->cmd_type in ide_init_drive_cmd() callers
ide: use wait_drive_not_busy() in drive_cmd_intr() (take 2)
ide: kill DATA_READY define
ide: task_end_request() fix
ide: use rq->nr_sectors in task_end_request()
ide: remove needless ->cursg clearing from task_end_request()
ide: set IDE_TFLAG_IN_* flags before queuing/executing command
ide-tape: fix handling of non-special requests in ->end_request method
ide: fix final status check in task_in_intr()
ide: clear HOB bit for REQ_TYPE_ATA_CMD requests in ide_end_drive_cmd()
ide: fix ->io_32bit race in ide_taskfile_ioctl()
cmd64x: remove /proc/ide/cmd64x
ide: remove broken disk byte-swapping support
...
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: (56 commits)
[S390] replace lock_cpu_hotplug with get_online_cpus
[S390] usage of s390dbf: shrink number of debug areas to use.
[S390] constify function pointer tables.
[S390] do local_irq_restore while spinning in spin_lock_irqsave.
[S390] add smp_call_function_mask
[S390] dasd: fix loop in request expiration handling
[S390] Unused field / extern declaration in processor.h
[S390] Remove TOPDIR from Makefile
[S390] dasd: add hyper PAV support to DASD device driver, part 1
[S390] single-step cleanup
[S390] Move NOTES and BUG_TABLE.
[S390] drivers/s390/: Spelling fixes
[S390] include/asm-s390/: Spelling fixes
[S390] arch/s390/: Spelling fixes
[S390] Use diag308 subcodes 3 and 6 for reboot and dump when possible.
[S390] vmemmap: allocate struct pages before 1:1 mapping
[S390] Initialize sclp_ipl_info
[S390] Allocate and free cpu lowcores and stacks when needed/possible.
[S390] use LIST_HEAD instead of LIST_HEAD_INIT
[S390] Load disabled wait psw instead of stopping cpu on halt.
...
Based on the earlier work by Tejun Heo.
All users are gone so we can finally remove it.
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on the earlier work by Tejun Heo.
There should be no functionality changes caused by this patch.
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on the earlier work by Tejun Heo.
Switch set_xfer_rate() to use REQ_TYPE_ATA_TASKFILE requests
and make ide_wait_cmd() static.
There should be no functionality changes caused by this patch.
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't check for READY_STAT bit being set for PIO-in protocol (makes the
final status check in drive_cmd_intr() match the one in task_in_intr()).
Also fix function name reported by ide_error() call while at it.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't enable local IRQs for PIO-in protocol in driver_cmd_intr().
While at it:
* Remove redundant rq->cmd_type check.
* Read status register after enabling local IRQs for no-data protocol.
v2:
* Re-add DRQ=1 check lost in v1 (noticed by Sergei).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on the previous work by Tejun Heo.
There should be no functionality changes caused by this patch.
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use wait_drive_not_busy() in drive_cmd_intr().
v2:
* Fix wait_drive_not_busy() comment (noticed by Sergei).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
task_end_request() modified to always call ide_end_drive_cmd()
for taskfile requests. Previously, ide_end_drive_cmd() was
called only when IDE_TFLAG_FLAGGED was set. Also,
ide_dma_intr() is modified to use task_end_request().
Enables TASKFILE ioctls to get valid register outputs on
successful completion.
Bart:
- ported it over recent IDE changes
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_TFLAG_{HOB,TF,DEVICE} defines.
* Set IDE_TFLAG_IN_* flags in {do_rw,ide_no_data,ide_raw}_taskfile() users.
* Remove no longer needed ->tf_flags setup from ide_end_drive_cmd().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Check for DRQ bit being cleared on the final status check.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_dump_status() may set HOB bit before ide_end_drive_cmd() is called.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In ide_taskfile_ioctl(), there was a race condition involving
drive->io_32bit. It was cleared and restored during ioctl
requests but there was no synchronization with other requests.
So, other requests could execute with the altered ->io_32bit
setting or updated drive->io_32bit could be overwritten by
ide_taskfile_ioctl().
This patch adds IDE_TFLAG_IO_16BIT flag to indicate to
ide_pio_datablock() that 16-bit I/O is needed regardless of
drive->io_32bit settting.
Bart:
- ported it over recent IDE changes
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This belongs to user-space (and only if really needed).
text data bss dec hex filename
3874 180 28 4082 ff2 drivers/ide/pci/cmd64x.o.before
2231 180 0 2411 96b drivers/ide/pci/cmd64x.o.after
Additionaly to being bloat the code reported incorrect UDMA modes for
the reserved values of UDIDETCR0/1 registers.
Also while at it remove unused CNTRL_DIS_RA0/1 defines.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove broken disk byte-swapping support:
- it can cause a data corruption on SMP (or if using PREEMPT on UP)
- all data coming from disk are byte-swapped by taskfile_*_data() which
results in incorrect identify data being reported by /proc/ide/ and IOCTLs
- "hdx=bswap/byteswap" kernel parameter has been broken on m68k host drivers
(including Atari/Q40 ones) since 2.5.x days (because of 'hwif' zero-ing)
- byte-swapping is limited to PIO transfers (for working with TiVo disks on
x86 machines using user-space solutions or dm-byteswap should result in
much better performance because DMA can be used)
For previous discussions please see:
http://www.ussg.iu.edu/hypermail/linux/kernel/0201.0/0768.htmlhttp://lkml.org/lkml/2004/2/28/111
[ I have dm-byteswap device mapper target if somebody is interested
(patch is for 2.6.4 though but I'll dust it off if needed). ]
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_busy_sleep() helper and use it in do_probe(),
enable_nest() and probe_hwif().
As a nice side-effect this fixes a minor bug in do_probe()
(the code was reading status register without any delay).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Print banner message once per controller in m68k host drivers.
* Change printk() level to KERN_INFO in buddha, falconide and gayle.
* Add banner message to q40ide.
This is basically a preparation for the future IDE layer changes.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move setting hwif->sg_max_nents from pmac_ide_setup_device()
to pmac_ide_setup_dma().
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move setting hwif->gendev.parent from ide_pci_setup_ports()
to ide_hwif_configure().
* Always set hwif->io_ports in ide_hwif_configure().
* Use ide_init_port_hw() in ide_hwif_configure().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide_init_hwif_ports() call in setup-pci.c::ide_hwif_configure()
doesn't depend on the default cotrol register offset, default IRQ
or ppc_ide_md.ide_init_hwif implementations so ide_std_init_ports()
can always be used.
* Since 'base' is always non-zero and thus hwif->io_ports[IDE_DATA_OFFSET]
is also non-zero always clear hwif->noprobe.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* hwif->hold is always set in au_ide_probe() (few lines earlier),
no need to set it again
* hwif->{channel,select_data,config_data} should be always zero
* autotune PIO also if CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA is defined
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make remaining built-in only IDE host drivers modular, add ide-scan-pci.c
file for probing PCI host drivers registered with IDE core (special case
for built-in IDE and CONFIG_IDEPCI_PCIBUS_ORDER=y) and then take care of
the ordering in which all IDE host drivers are probed when IDE is built-in
during link time.
* Move probing of gayle, falconide, macide, q40ide and buddha (m68k arch
specific) host drivers, before PCI ones (no PCI on m68k), ide-cris (cris
arch specific), cmd640 (x86 arch specific) and pmac (ppc arch specific).
* Move probing of ide-cris (cris arch specific) host driver before cmd640
(x86 arch specific).
* Move probing of mpc8xx (ppc specific) host driver before ide-pnp (depends
on ISA and none of ppc platform that use mpc8xx supports ISA) and ide-h8300
(h8300 arch specific).
* Add "probe_vlb" kernel parameter to cmd640 host driver and update
Documentation/ide.txt accordingly.
* Make IDE_ARM config option visible so it can also be disabled if needed.
* Remove bogus comment from ide.c while at it.
v2:
* Fix two issues spotted by Sergei:
- replace ENOMEM error value by ENOENT in ide-h8300 host driver
- fix MODULE_PARM_DESC() in cmd640 host driver
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add mpc8xx_ide_probe() to mpc8xx.c and call it from probe_for_hwifs().
* Convert ide_arm, ide-cris, ide-h8300, ide-pnp, buddha, falconide, gayle,
macide, q40ide, cmd640 and mpc8xx host drivers to use ide_device_add().
This removes dependency on ide_generic for these drivers so update
ide/Kconfig accordingly.
v2:
* ide_arm build fix (s/ide_device_idx/ide_device_add/)
(Thanks to Christoph Lameter <clameter@sgi.com> for reporting the problem).
Cc: Mikael Starvik <starvik@axis.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove ide_init_port_data() call from ide_arm_init() and move
ide_arm_init() call from init_ide_data() to ide_init().
This patch is a preparation for the future changes (and as a side-effect
makes obsolete "idex=io[,ctl[,irq]]" kernel parameters work for ide_arm).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename init_hwif_data() to ide_init_port_data() and export it.
* For all users of ide_register_hw() with 'initializing' argument set
hwif->present and hwif->hold are always zero so convert these host
drivers to use ide_find_port()+ide_init_port_data()+ide_init_port_hw()
instead (also no need for init_hwif_default() call since the setup
done by it gets over-ridden by ide_init_port_hw() call).
* Drop 'initializing' argument from ide_register_hw().
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_init_port_hw() helper.
* rapide.c: convert rapide_locate_hwif() to rapide_setup_ports()
and use ide_init_port_hw().
* ide_platform.c: convert plat_ide_locate_hwif() to plat_ide_setup_ports()
and use ide_init_port_hw().
* sgiioc4.c: use ide_init_port_hw().
* pmac.c: add 'hw_regs_t *hw' argument to pmac_ide_setup_device(),
setup 'hw' in pmac_ide_{macio,pci}_attach() and use ide_init_port_hw()
in pmac_ide_setup_device().
This patch is a preparation for the future changes in the IDE probing code.
There should be no functionality changes caused by this patch.
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Jeremy Higdon <jeremy@sgi.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cliff Cai