It turns out that it is advantageous to leave a small portion of unmapped file
backed pages if all of a zone's pages (or almost all pages) are allocated and
so the page allocator has to go off-node.
This allows recently used file I/O buffers to stay on the node and
reduces the times that zone reclaim is invoked if file I/O occurs
when we run out of memory in a zone.
The problem is that zone reclaim runs too frequently when the page cache is
used for file I/O (read write and therefore unmapped pages!) alone and we have
almost all pages of the zone allocated. Zone reclaim may remove 32 unmapped
pages. File I/O will use these pages for the next read/write requests and the
unmapped pages increase. After the zone has filled up again zone reclaim will
remove it again after only 32 pages. This cycle is too inefficient and there
are potentially too many zone reclaim cycles.
With the 1% boundary we may still remove all unmapped pages for file I/O in
zone reclaim pass. However. it will take a large number of read and writes
to get back to 1% again where we trigger zone reclaim again.
The zone reclaim 2.6.16/17 does not show this behavior because we have a 30
second timeout.
[akpm@osdl.org: rename the /proc file and the variable]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ACPI supplies a "shareable" indication, but PNPACPI ignores it. If a PNP
device uses a shared interrupt, request_irq() fails because the PNP driver
can't tell whether to supply SA_SHIRQ.
This patch allows PNP drivers to test
(pnp_irq_flags(dev, 0) & IORESOURCE_IRQ_SHAREABLE)
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Matthieu Castet <castet.matthieu@free.fr>
Cc: Li Shaohua <shaohua.li@intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Have a special version of print_symbol() for s390 which clears the most
significant bit of addr before calling __print_symbol(). This seems to be
better than checking/changing each place in the kernel that saves an
instruction pointer.
Without this the output would look like:
hardirqs last enabled at (30907): [<80018c6a>] 0x80018c6a
hardirqs last disabled at (30908): [<8001e48c>] 0x8001e48c
softirqs last enabled at (30904): [<8001dc96>] 0x8001dc96
softirqs last disabled at (30897): [<8001dc50>] 0x8001dc50
instead of this:
hardirqs last enabled at (19421): [<80018c72>] cpu_idle+0x176/0x1c4
hardirqs last disabled at (19422): [<8001e494>] io_no_vtime+0xa/0x1a
softirqs last enabled at (19418): [<8001dc9e>] do_softirq+0xa6/0xe8
softirqs last disabled at (19411): [<8001dc58>] do_softirq+0x60/0xe8
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
include/linux/version.h contained both actual KERNEL version
and UTS_RELEASE that contains a subset from git SHA1 for when
kernel was compiled as part of a git repository.
This had the unfortunate side-effect that all files including version.h
would be recompiled when some git changes was made due to changes SHA1.
Split it out so we keep independent parts in separate files.
Also update checkversion.pl script to no longer check for UTS_RELEASE.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The irqflags consolidation converted SA_PERCPU_IRQ to IRQF_PERCPU but
did not define the new constant.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Linus: "The hacks in kernel/irq/handle.c are really horrid. REALLY
horrid."
They are indeed. Move the dyntick quirks to ARM where they belong.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The recent interrupt rework introduced bit value conflicts with sparc.
Instead of introducing new architecture flags mess, move the interrupt SA_
flags out of the signal namespace and replace them by interrupt related flags.
This allows to remove the obsolete SA_INTERRUPT flag and clean up the bit
field values.
This patch:
Move the interrupt related SA_ flags out of linux/signal.h and rename them to
IRQF_ . This moves the interrupt related flags out of the signal namespace
and allows to remove the architecture dependencies.
SA_INTERRUPT is not needed by userspace and glibc so it can be removed safely.
The existing SA_ constants are kept for easy transition and will be
removed after a 6 month grace period.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Greg KH <greg@kroah.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Jody McIntyre <scjody@modernduck.com>
Cc: Ben Collins <bcollins@debian.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Jens Axboe <axboe@suse.de>
Cc: Chris Zankel <chris@zankel.net>
Cc: Andi Kleen <ak@muc.de>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: David Howells <dhowells@redhat.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some UARTs have more than 255 bytes of FIFO, which can't be
represented by an unsigned char. Change the kernel's internal
structure to be an unsigned int, but still export an unsigned char
via the TIOCGSERIAL ioctl. If the TIOCSSERIAL ioctl provides a
fifo size of 0, assume this means "don't change" otherwise we'll
corrupt the larger fifo sizes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add ids for SDHCI controllers so that they can be identified for quirks.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
ARM has a couple of really dumb interrupt controllers.
Implement a generic one and fixup the ARM migration. ARM reused
the no_irq_chip for this purpose, but this does not work out
for platforms which are not converted to the new interrupt
type handling model.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Always use do {} while (0). Failing to do so can cause subtle compile
failures or bugs.
Cc: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Raise the maximum error number in IS_ERR_VALUE to 4095.
o Make that number available as a new constant MAX_ERRNO.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes buggy behaviour of UFS
in such kind of scenario:
open(, O_TRUNC...)
ftruncate(, 1024)
ftruncate(, 0)
Such a scenario causes ufs_panic and remount read-only. This happen
because of according to specification UFS should always allocate block for
last byte, and many parts of our implementation rely on this, but
`ufs_truncate' doesn't care about this.
To make possible return error code and to know about old size, this patch
removes `truncate' from ufs inode_operations and uses `setattr' method to
call ufs_truncate.
Signed-off-by: Evgeniy Dushistov <dushistov@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow to tie upper bits of syscall bitmap in audit rules to kernel-defined
sets of syscalls. Infrastructure, a couple of classes (with 32bit counterparts
for biarch targets) and actual tie-in on i386, amd64 and ia64.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch renames some audit constant definitions and adds
additional definitions used by the following patch. The renaming
avoids ambiguity with respect to the new definitions.
Signed-off-by: Darrel Goeddel <dgoeddel@trustedcs.com>
include/linux/audit.h | 15 ++++++++----
kernel/auditfilter.c | 50 ++++++++++++++++++++---------------------
kernel/auditsc.c | 10 ++++----
security/selinux/ss/services.c | 32 +++++++++++++-------------
4 files changed, 56 insertions(+), 51 deletions(-)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add support for a rule key, which can be used to tie audit records to audit
rules. This is useful when a watched file is accessed through a link or
symlink, as well as for general audit log analysis.
Because this patch uses a string key instead of an integer key, there is a bit
of extra overhead to do the kstrdup() when a rule fires. However, we're also
allocating memory for the audit record buffer, so it's probably not that
significant. I went ahead with a string key because it seems more
user-friendly.
Note that the user must ensure that filterkeys are unique. The kernel only
checks for duplicate rules.
Signed-off-by: Amy Griffis <amy.griffis@hpd.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPV6]: Added GSO support for TCPv6
[NET]: Generalise TSO-specific bits from skb_setup_caps
[IPV6]: Added GSO support for TCPv6
[IPV6]: Remove redundant length check on input
[NETFILTER]: SCTP conntrack: fix crash triggered by packet without chunks
[TG3]: Update version and reldate
[TG3]: Add TSO workaround using GSO
[TG3]: Turn on hw fix for ASF problems
[TG3]: Add rx BD workaround
[TG3]: Add tg3_netif_stop() in vlan functions
[TCP]: Reset gso_segs if packet is dodgy
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6/:
[PATCH] pcmcia: fix deadlock in pcmcia_parse_events
[PATCH] com20020_cs: more device support
[PATCH] au1xxx: pcmcia: fix __init called from non-init
[PATCH] kill open-coded offsetof in cm4000_cs.c ZERO_DEV()
[PATCH] pcmcia: convert pcmcia_cs to kthread
[PATCH] pcmcia: fix kernel-doc function name
[PATCH] pcmcia: hostap_cs.c - 0xc00f,0x0000 conflicts with pcnet_cs
[PATCH] pcmcia: at91_cf suspend/resume/wakeup
[PATCH] pcmcia: Make ide_cs work with the memory space of CF-Cards if IO space is not available
[PATCH] pcmcia: TI PCIxx12 CardBus controller support
[PATCH] pcmcia: warn if driver requests exclusive, but gets a shared IRQ
[PATCH] pcmcia: expose tool in pcmcia/Documentation/pcmcia/
[PATCH] pcmcia: another ID for serial_cs.c
[PATCH] yenta: fix hidden PCI bus numbers
[PATCH] yenta: do power-up only after socket is configured
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (25 commits)
ACPI: Kconfig: ACPI_SRAT depends on ACPI
ACPI: drivers/acpi/scan.c: make acpi_bus_type static
ACPI: fixup memhotplug debug message
ACPI: ACPICA 20060623
ACPI: C-States: only demote on current bus mastering activity
ACPI: C-States: bm_activity improvements
ACPI: C-States: accounting of sleep states
ACPI: additional blacklist entry for ThinkPad R40e
ACPI: restore comment justifying 'extra' P_LVLx access
ACPI: fix battery on HP NX6125
ACPIPHP: prevent duplicate slot numbers when no _SUN
ACPI: static-ize handle_hotplug_event_func()
ACPIPHP: use ACPI dock driver
ACPI: dock driver
KEVENT: add new uevent for dock
ACPI: asus_acpi_init: propagate correct return value
[ACPI] Print error message if remove/install notify handler fails
ACPI: delete tracing macros from drivers/acpi/*.c
ACPI: HW P-state coordination support
ACPI: un-export ACPI_ERROR() -- use printk(KERN_ERR...)
...
This patch adds GSO support for IPv6 and TCPv6. This is based on a patch
by Ananda Raju <Ananda.Raju@neterion.com>. His original description is:
This patch enables TSO over IPv6. Currently Linux network stacks
restricts TSO over IPv6 by clearing of the NETIF_F_TSO bit from
"dev->features". This patch will remove this restriction.
This patch will introduce a new flag NETIF_F_TSO6 which will be used
to check whether device supports TSO over IPv6. If device support TSO
over IPv6 then we don't clear of NETIF_F_TSO and which will make the
TCP layer to create TSO packets. Any device supporting TSO over IPv6
will set NETIF_F_TSO6 flag in "dev->features" along with NETIF_F_TSO.
In case when user disables TSO using ethtool, NETIF_F_TSO will get
cleared from "dev->features". So even if we have NETIF_F_TSO6 we don't
get TSO packets created by TCP layer.
SKB_GSO_TCPV4 renamed to SKB_GSO_TCP to make it generic GSO packet.
SKB_GSO_UDPV4 renamed to SKB_GSO_UDP as UFO is not a IPv4 feature.
UFO is supported over IPv6 also
The following table shows there is significant improvement in
throughput with normal frames and CPU usage for both normal and jumbo.
--------------------------------------------------
| | 1500 | 9600 |
| ------------------|-------------------|
| | thru CPU | thru CPU |
--------------------------------------------------
| TSO OFF | 2.00 5.5% id | 5.66 20.0% id |
--------------------------------------------------
| TSO ON | 2.63 78.0 id | 5.67 39.0% id |
--------------------------------------------------
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch generalises the TSO-specific bits from sk_setup_caps by adding
the sk_gso_type member to struct sock. This makes sk_setup_caps generic
so that it can be used by TCPv6 or UFO.
The only catch is that whoever uses this must provide a GSO implementation
for their protocol which I think is a fair deal :) For now UFO continues to
live without a GSO implementation which is OK since it doesn't use the sock
caps field at the moment.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch below adds support for the TI PCIxx12 CardBus controllers.
This seems to be sufficient to detect the cardbus bridge on an HP nc6320
and works with an orinoco wifi card.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Add a rq_sendfile_ok flag to svc_rqst which will be cleared in the privacy
case so that the wrapping code will get copies of the read data instead of
real page cache pages. This makes life simpler when we encrypt the response.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add __acquire annotations to rcu_read_lock and rcu_read_lock_bh, and add
__release annotations to rcu_read_unlock and rcu_read_unlock_bh. This
allows sparse to detect improperly paired calls to these functions.
Signed-off-by: Josh Triplett <josh@freedesktop.org>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This corrects the comments describing the 'enabled' and 'pending' flags in
struct rtc_wkalrm of include/linux/rtc.h.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Presently, smp_processor_id() isn't necessarily set up until setup_arch().
But it's used in boot_cpu_init() and printk() and perhaps in other places,
prior to setup_arch() being called.
So provide a new smp_setup_processor_id() which is called before anything
else, wire it up for Voyager (which boots on a CPU other than #0, and broke).
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new security hook definition for the sys_ioprio_get operation. At
present, the SELinux hook function implementation for this hook is
identical to the getscheduler implementation but a separate hook is
introduced to allow this check to be specialized in the future if
necessary.
This patch also creates a helper function get_task_ioprio which handles the
access check in addition to retrieving the ioprio value for the task.
Signed-off-by: David Quigley <dpquigl@tycho.nsa.gov>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a call to the extended security_task_kill hook introduced by
the prior patch to the kill_proc_info_as_uid function so that these signals
can be properly mediated by security modules. It also updates the existing
hook call in check_kill_permission.
Signed-off-by: David Quigley <dpquigl@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch extends the security_task_kill hook to handle signals sent by AIO
completion. In this case, the secid of the task responsible for the signal
needs to be obtained and saved earlier, so a security_task_getsecid() hook is
added, and then this saved value is passed subsequently to the extended
task_kill hook for use in checking.
Signed-off-by: David Quigley <dpquigl@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The remaining counters in page_state after the zoned VM counter patches
have been applied are all just for show in /proc/vmstat. They have no
essential function for the VM.
We use a simple increment of per cpu variables. In order to avoid the most
severe races we disable preempt. Preempt does not prevent the race between
an increment and an interrupt handler incrementing the same statistics
counter. However, that race is exceedingly rare, we may only loose one
increment or so and there is no requirement (at least not in kernel) that
the vm event counters have to be accurate.
In the non preempt case this results in a simple increment for each
counter. For many architectures this will be reduced by the compiler to a
single instruction. This single instruction is atomic for i386 and x86_64.
And therefore even the rare race condition in an interrupt is avoided for
both architectures in most cases.
The patchset also adds an off switch for embedded systems that allows a
building of linux kernels without these counters.
The implementation of these counters is through inline code that hopefully
results in only a single instruction increment instruction being emitted
(i386, x86_64) or in the increment being hidden though instruction
concurrency (EPIC architectures such as ia64 can get that done).
Benefits:
- VM event counter operations usually reduce to a single inline instruction
on i386 and x86_64.
- No interrupt disable, only preempt disable for the preempt case.
Preempt disable can also be avoided by moving the counter into a spinlock.
- Handling is similar to zoned VM counters.
- Simple and easily extendable.
- Can be omitted to reduce memory use for embedded use.
References:
RFC http://marc.theaimsgroup.com/?l=linux-kernel&m=113512330605497&w=2
RFC http://marc.theaimsgroup.com/?l=linux-kernel&m=114988082814934&w=2
local_t http://marc.theaimsgroup.com/?l=linux-kernel&m=114991748606690&w=2
V2 http://marc.theaimsgroup.com/?t=115014808400007&r=1&w=2
V3 http://marc.theaimsgroup.com/?l=linux-kernel&m=115024767022346&w=2
V4 http://marc.theaimsgroup.com/?l=linux-kernel&m=115047968808926&w=2
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The numa statistics are really event counters. But they are per node and
so we have had special treatment for these counters through additional
fields on the pcp structure. We can now use the per zone nature of the
zoned VM counters to realize these.
This will shrink the size of the pcp structure on NUMA systems. We will
have some room to add additional per zone counters that will all still fit
in the same cacheline.
Bits Prior pcp size Size after patch We can add
------------------------------------------------------------------
64 128 bytes (16 words) 80 bytes (10 words) 48
32 76 bytes (19 words) 56 bytes (14 words) 8 (64 byte cacheline)
72 (128 byte)
Remove the special statistics for numa and replace them with zoned vm
counters. This has the side effect that global sums of these events now
show up in /proc/vmstat.
Also take the opportunity to move the zone_statistics() function from
page_alloc.c into vmstat.c.
Discussions:
V2 http://marc.theaimsgroup.com/?t=115048227000002&r=1&w=2
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
No callers.
Cc: Christoph Lameter <clameter@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_bounce to a per zone counter
nr_bounce is only used for proc output. So it could be left as an event
counter. However, the event counters may not be accurate and nr_bounce is
categorizing types of pages in a zone. So we really need this to also be a
per zone counter.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_unstable to a per zone counter
We need to do some special modifications to the nfs code since there are
multiple cases of disposition and we need to have a page ref for proper
accounting.
This converts the last critical page state of the VM and therefore we need to
remove several functions that were depending on GET_PAGE_STATE_LAST in order
to make the kernel compile again. We are only left with event type counters
in page state.
[akpm@osdl.org: bugfixes]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_writeback to per zone counter.
This removes the last page_state counter from arch/i386/mm/pgtable.c so we
drop the page_state from there.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes nr_dirty a per zone counter. Looping over all processors is
avoided during writeback state determination.
The counter aggregation for nr_dirty had to be undone in the NFS layer since
we summed up the page counts from multiple zones. Someone more familiar with
NFS should probably review what I have done.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_page_table_pages to a per zone counter
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Allows reclaim to access counter without looping over processor counts.
- Allows accurate statistics on how many pages are used in a zone by
the slab. This may become useful to balance slab allocations over
various zones.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The zone_reclaim_interval was necessary because we were not able to determine
how many unmapped pages exist in a zone. Therefore we had to scan in
intervals to figure out if any pages were unmapped.
With the zoned counters and NR_ANON_PAGES we now know the number of pagecache
pages and the number of mapped pages in a zone. So we can simply skip the
reclaim if there is an insufficient number of unmapped pages. We use
SWAP_CLUSTER_MAX as the boundary.
Drop all support for /proc/sys/vm/zone_reclaim_interval.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current NR_FILE_MAPPED is used by zone reclaim and the dirty load
calculation as the number of mapped pagecache pages. However, that is not
true. NR_FILE_MAPPED includes the mapped anonymous pages. This patch
separates those and therefore allows an accurate tracking of the anonymous
pages per zone.
It then becomes possible to determine the number of unmapped pages per zone
and we can avoid scanning for unmapped pages if there are none.
Also it may now be possible to determine the mapped/unmapped ratio in
get_dirty_limit. Isnt the number of anonymous pages irrelevant in that
calculation?
Note that this will change the meaning of the number of mapped pages reported
in /proc/vmstat /proc/meminfo and in the per node statistics. This may affect
user space tools that monitor these counters! NR_FILE_MAPPED works like
NR_FILE_DIRTY. It is only valid for pagecache pages.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently a single atomic variable is used to establish the size of the page
cache in the whole machine. The zoned VM counters have the same method of
implementation as the nr_pagecache code but also allow the determination of
the pagecache size per zone.
Remove the special implementation for nr_pagecache and make it a zoned counter
named NR_FILE_PAGES.
Updates of the page cache counters are always performed with interrupts off.
We can therefore use the __ variant here.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
nr_mapped is important because it allows a determination of how many pages of
a zone are not mapped, which would allow a more efficient means of determining
when we need to reclaim memory in a zone.
We take the nr_mapped field out of the page state structure and define a new
per zone counter named NR_FILE_MAPPED (the anonymous pages will be split off
from NR_MAPPED in the next patch).
We replace the use of nr_mapped in various kernel locations. This avoids the
looping over all processors in try_to_free_pages(), writeback, reclaim (swap +
zone reclaim).
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Per zone counter infrastructure
The counters that we currently have for the VM are split per processor. The
processor however has not much to do with the zone these pages belong to. We
cannot tell f.e. how many ZONE_DMA pages are dirty.
So we are blind to potentially inbalances in the usage of memory in various
zones. F.e. in a NUMA system we cannot tell how many pages are dirty on a
particular node. If we knew then we could put measures into the VM to balance
the use of memory between different zones and different nodes in a NUMA
system. For example it would be possible to limit the dirty pages per node so
that fast local memory is kept available even if a process is dirtying huge
amounts of pages.
Another example is zone reclaim. We do not know how many unmapped pages exist
per zone. So we just have to try to reclaim. If it is not working then we
pause and try again later. It would be better if we knew when it makes sense
to reclaim unmapped pages from a zone. This patchset allows the determination
of the number of unmapped pages per zone. We can remove the zone reclaim
interval with the counters introduced here.
Futhermore the ability to have various usage statistics available will allow
the development of new NUMA balancing algorithms that may be able to improve
the decision making in the scheduler of when to move a process to another node
and hopefully will also enable automatic page migration through a user space
program that can analyse the memory load distribution and then rebalance
memory use in order to increase performance.
The counter framework here implements differential counters for each processor
in struct zone. The differential counters are consolidated when a threshold
is exceeded (like done in the current implementation for nr_pageache), when
slab reaping occurs or when a consolidation function is called.
Consolidation uses atomic operations and accumulates counters per zone in the
zone structure and also globally in the vm_stat array. VM functions can
access the counts by simply indexing a global or zone specific array.
The arrangement of counters in an array also simplifies processing when output
has to be generated for /proc/*.
Counters can be updated by calling inc/dec_zone_page_state or
_inc/dec_zone_page_state analogous to *_page_state. The second group of
functions can be called if it is known that interrupts are disabled.
Special optimized increment and decrement functions are provided. These can
avoid certain checks and use increment or decrement instructions that an
architecture may provide.
We also add a new CONFIG_DMA_IS_NORMAL that signifies that an architecture can
do DMA to all memory and therefore ZONE_NORMAL will not be populated. This is
only currently set for IA64 SGI SN2 and currently only affects
node_page_state(). In the best case node_page_state can be reduced to
retrieving a single counter for the one zone on the node.
[akpm@osdl.org: cleanups]
[akpm@osdl.org: export vm_stat[] for filesystems]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NOTE: ZVC are *not* the lightweight event counters. ZVCs are reliable whereas
event counters do not need to be.
Zone based VM statistics are necessary to be able to determine what the state
of memory in one zone is. In a NUMA system this can be helpful for local
reclaim and other memory optimizations that may be able to shift VM load in
order to get more balanced memory use.
It is also useful to know how the computing load affects the memory
allocations on various zones. This patchset allows the retrieval of that data
from userspace.
The patchset introduces a framework for counters that is a cross between the
existing page_stats --which are simply global counters split per cpu-- and the
approach of deferred incremental updates implemented for nr_pagecache.
Small per cpu 8 bit counters are added to struct zone. If the counter exceeds
certain thresholds then the counters are accumulated in an array of
atomic_long in the zone and in a global array that sums up all zone values.
The small 8 bit counters are next to the per cpu page pointers and so they
will be in high in the cpu cache when pages are allocated and freed.
Access to VM counter information for a zone and for the whole machine is then
possible by simply indexing an array (Thanks to Nick Piggin for pointing out
that approach). The access to the total number of pages of various types does
no longer require the summing up of all per cpu counters.
Benefits of this patchset right now:
- Ability for UP and SMP configuration to determine how memory
is balanced between the DMA, NORMAL and HIGHMEM zones.
- loops over all processors are avoided in writeback and
reclaim paths. We can avoid caching the writeback information
because the needed information is directly accessible.
- Special handling for nr_pagecache removed.
- zone_reclaim_interval vanishes since VM stats can now determine
when it is worth to do local reclaim.
- Fast inline per node page state determination.
- Accurate counters in /sys/devices/system/node/node*/meminfo. Current
counters are counting simply which processor allocated a page somewhere
and guestimate based on that. So the counters were not useful to show
the actual distribution of page use on a specific zone.
- The swap_prefetch patch requires per node statistics in order to
figure out when processors of a node can prefetch. This patch provides
some of the needed numbers.
- Detailed VM counters available in more /proc and /sys status files.
References to earlier discussions:
V1 http://marc.theaimsgroup.com/?l=linux-kernel&m=113511649910826&w=2
V2 http://marc.theaimsgroup.com/?l=linux-kernel&m=114980851924230&w=2
V3 http://marc.theaimsgroup.com/?l=linux-kernel&m=115014697910351&w=2
V4 http://marc.theaimsgroup.com/?l=linux-kernel&m=115024767318740&w=2
Performance tests with AIM7 did not show any regressions. Seems to be a tad
faster even. Tested on ia64/NUMA. Builds fine on i386, SMP / UP. Includes
fixes for s390/arm/uml arch code.
This patch:
Move counter code from page_alloc.c/page-flags.h to vmstat.c/h.
Create vmstat.c/vmstat.h by separating the counter code and the proc
functions.
Move the vm_stat_text array before zoneinfo_show.
[akpm@osdl.org: s390 build fix]
[akpm@osdl.org: HOTPLUG_CPU build fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
skb_release_data() no longer has any users in other files.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current TSO implementation, NETIF_F_TSO and ECN cannot be
turned on together in a TCP connection. The problem is that most
hardware that supports TSO does not handle CWR correctly if it is set
in the TSO packet. Correct handling requires CWR to be set in the
first packet only if it is set in the TSO header.
This patch adds the ability to turn on NETIF_F_TSO and ECN using
GSO if necessary to handle TSO packets with CWR set. Hardware
that handles CWR correctly can turn on NETIF_F_TSO_ECN in the dev->
features flag.
All TSO packets with CWR set will have the SKB_GSO_TCPV4_ECN set. If
the output device does not have the NETIF_F_TSO_ECN feature set, GSO
will split the packet up correctly with CWR only set in the first
segment.
With help from Herbert Xu <herbert@gondor.apana.org.au>.
Since ECN can always be enabled with TSO, the SOCK_NO_LARGESEND sock
flag is completely removed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements an API whereby an application can determine the
label of its peer's Unix datagram sockets via the auxiliary data mechanism of
recvmsg.
Patch purpose:
This patch enables a security-aware application to retrieve the
security context of the peer of a Unix datagram socket. The application
can then use this security context to determine the security context for
processing on behalf of the peer who sent the packet.
Patch design and implementation:
The design and implementation is very similar to the UDP case for INET
sockets. Basically we build upon the existing Unix domain socket API for
retrieving user credentials. Linux offers the API for obtaining user
credentials via ancillary messages (i.e., out of band/control messages
that are bundled together with a normal message). To retrieve the security
context, the application first indicates to the kernel such desire by
setting the SO_PASSSEC option via getsockopt. Then the application
retrieves the security context using the auxiliary data mechanism.
An example server application for Unix datagram socket should look like this:
toggle = 1;
toggle_len = sizeof(toggle);
setsockopt(sockfd, SOL_SOCKET, SO_PASSSEC, &toggle, &toggle_len);
recvmsg(sockfd, &msg_hdr, 0);
if (msg_hdr.msg_controllen > sizeof(struct cmsghdr)) {
cmsg_hdr = CMSG_FIRSTHDR(&msg_hdr);
if (cmsg_hdr->cmsg_len <= CMSG_LEN(sizeof(scontext)) &&
cmsg_hdr->cmsg_level == SOL_SOCKET &&
cmsg_hdr->cmsg_type == SCM_SECURITY) {
memcpy(&scontext, CMSG_DATA(cmsg_hdr), sizeof(scontext));
}
}
sock_setsockopt is enhanced with a new socket option SOCK_PASSSEC to allow
a server socket to receive security context of the peer.
Testing:
We have tested the patch by setting up Unix datagram client and server
applications. We verified that the server can retrieve the security context
using the auxiliary data mechanism of recvmsg.
Signed-off-by: Catherine Zhang <cxzhang@watson.ibm.com>
Acked-by: Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test in skb_gso_ok is backwards. Noticed by Michael Chan
<mchan@broadcom.com>.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch encapsulates the usage of eff_cap (in netlink_skb_params) within
the security framework by extending security_netlink_recv to include a required
capability parameter and converting all direct usage of eff_caps outside
of the lsm modules to use the interface. It also updates the SELinux
implementation of the security_netlink_send and security_netlink_recv
hooks to take advantage of the sid in the netlink_skb_params struct.
This also enables SELinux to perform auditing of netlink capability checks.
Please apply, for 2.6.18 if possible.
Signed-off-by: Darrel Goeddel <dgoeddel@trustedcs.com>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When GSO packets come from an untrusted source (e.g., a Xen guest domain),
we need to verify the header integrity before passing it to the hardware.
Since the first step in GSO is to verify the header, we can reuse that
code by adding a new bit to gso_type: SKB_GSO_DODGY. Packets with this
bit set can only be fed directly to devices with the corresponding bit
NETIF_F_GSO_ROBUST. If the device doesn't have that bit, then the skb
is fed to the GSO engine which will allow the packet to be sent to the
hardware if it passes the header check.
This patch changes the sg flag to a full features flag. The same method
can be used to implement TSO ECN support. We simply have to mark packets
with CWR set with SKB_GSO_ECN so that only hardware with a corresponding
NETIF_F_TSO_ECN can accept them. The GSO engine can either fully segment
the packet, or segment the first MTU and pass the rest to the hardware for
further segmentation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (33 commits)
[MIPS] Add missing backslashes to macro definitions.
[MIPS] Death list of board support to be removed after 2.6.18.
[MIPS] Remove BSD and Sys V compat data types.
[MIPS] ioc3.h: Uses u8, so include <linux/types.h>.
[MIPS] 74K: Assume it will also have an AR bit in config7
[MIPS] Treat CPUs with AR bit as physically indexed.
[MIPS] Oprofile: Support VSMP on 34K.
[MIPS] MIPS32/MIPS64 S-cache fix and cleanup
[MIPS] excite: PCI makefile needs to use += if it wants a chance to work.
[MIPS] excite: plat_setup -> plat_mem_setup.
[MIPS] au1xxx: export dbdma functions
[MIPS] au1xxx: dbdma, no sleeping under spin_lock
[MIPS] au1xxx: fix PSC_SMBTXRX_RSR.
[MIPS] Early printk for IP27.
[MIPS] Fix handling of 0 length I & D caches.
[MIPS] Typo fixes.
[MIPS] MIPS32/MIPS64 secondary cache management
[MIPS] Fix FIXADDR_TOP for TX39/TX49.
[MIPS] Remove first timer interrupt setup in wrppmc_timer_setup()
[MIPS] Fix configuration of R2 CPU features and multithreading.
...
They have been obsoleted by the ELF header EI_CLASS and EI_DATA fields
in combination with e_flags. Afaics EM_MIPS_RS3_LE and EM_MIPS_RS4_BE
never had any practical relevance. Binutils will not produce such
binaries and the kernel will not accept them as MIPS binaries.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] i386: export memory more than 4G through /proc/iomem
[PATCH] 64bit Resource: finally enable 64bit resource sizes
[PATCH] 64bit Resource: convert a few remaining drivers to use resource_size_t where needed
[PATCH] 64bit resource: change pnp core to use resource_size_t
[PATCH] 64bit resource: change pci core and arch code to use resource_size_t
[PATCH] 64bit resource: change resource core to use resource_size_t
[PATCH] 64bit resource: introduce resource_size_t for the start and end of struct resource
[PATCH] 64bit resource: fix up printks for resources in misc drivers
[PATCH] 64bit resource: fix up printks for resources in arch and core code
[PATCH] 64bit resource: fix up printks for resources in pcmcia drivers
[PATCH] 64bit resource: fix up printks for resources in video drivers
[PATCH] 64bit resource: fix up printks for resources in ide drivers
[PATCH] 64bit resource: fix up printks for resources in mtd drivers
[PATCH] 64bit resource: fix up printks for resources in pci core and hotplug drivers
[PATCH] 64bit resource: fix up printks for resources in networks drivers
[PATCH] 64bit resource: fix up printks for resources in sound drivers
[PATCH] 64bit resource: C99 changes for struct resource declarations
Fixed up trivial conflict in drivers/ide/pci/cmd64x.c (the printk that
was changed by the 64-bit resources had been deleted in the meantime ;)
Clean up the fastack concept by turning it into fasteoi and introducing the
->eoi() method for chips.
This also allows the cleanup of an i386 EOI quirk - now the quirk is
cleanly separated from the pure ACK implementation.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a #define for the mask of the part of IRQ_TYPE that represents the
trigger type. I use that in my in-progress work as I've standardized the
way the irq description in the firmware device-tree get translated to linux
useable things by using those constants. Having this mask to isolate the
"trigger type" part of the flags is useful in a few places.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable platforms to set the irq-wake (power-management) properties of an IRQ.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable platforms to use the irq-chip and irq-flow abstractions: allow setting
of the chip, the type and provide highlevel handlers for common irq-flows.
[rostedt@goodmis.org: misroute-irq: Don't call desc->chip->end because of edge interrupts]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a fixed up and cleaned up replacement for genirq-msi-fixes.patch,
which should solve the i386 4KSTACKS problem. I also added Ben's idea of
pushing the __do_IRQ() check into generic_handle_irq().
I booted this with MSI enabled, but i only have MSI devices, not MSI-X
devices. I'd still expect MSI-X to work now.
irqchip migration helper: call __do_IRQ() if a descriptor is attached to an
irqtype-style controller. This also fixes MSI-X IRQ handling on i386 and
x86_64.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable platforms to disable the automatic enabling of freshly set up irqs.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable platforms to disable request_irq() for certain interrupts.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable platforms that do not have a hardware-assisted hardirq-resend mechanism
to resend them via a softirq-driven IRQ emulation mechanism.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add ->retrigger() irq op to consolidate hw_irq_resend() implementations.
(Most architectures had it defined to NOP anyway.)
NOTE: ia64 needs testing. i386 and x86_64 tested.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Consolidation: remove the pending_irq_cpumask[NR_IRQS] array and move it into
the irq_desc[NR_IRQS].pending_mask field.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Consolidation: remove the irq_dir[NR_IRQS] and the smp_affinity_entry[NR_IRQS]
arrays and move them into the irq_desc[] array.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Small cleanups in include/linux/irq.h.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cleanup: remove irq_desc_t use from the generic IRQ code, and mark it
obsolete.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that i386 defaults to regparm, explicit uses of fastcall are not needed
anymore.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cleanup: remove irq_descp() - explicit use of irq_desc[] is shorter and more
readable.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Consolidation: remove the irq_affinity[NR_IRQS] array and move it into the
irq_desc[NR_IRQS].affinity field.
[akpm@osdl.org: sparc64 build fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch-queue improves the generic IRQ layer to be truly generic, by adding
various abstractions and features to it, without impacting existing
functionality.
While the queue can be best described as "fix and improve everything in the
generic IRQ layer that we could think of", and thus it consists of many
smaller features and lots of cleanups, the one feature that stands out most is
the new 'irq chip' abstraction.
The irq-chip abstraction is about describing and coding and IRQ controller
driver by mapping its raw hardware capabilities [and quirks, if needed] in a
straightforward way, without having to think about "IRQ flow"
(level/edge/etc.) type of details.
This stands in contrast with the current 'irq-type' model of genirq
architectures, which 'mixes' raw hardware capabilities with 'flow' details.
The patchset supports both types of irq controller designs at once, and
converts i386 and x86_64 to the new irq-chip design.
As a bonus side-effect of the irq-chip approach, chained interrupt controllers
(master/slave PIC constructs, etc.) are now supported by design as well.
The end result of this patchset intends to be simpler architecture-level code
and more consolidation between architectures.
We reused many bits of code and many concepts from Russell King's ARM IRQ
layer, the merging of which was one of the motivations for this patchset.
This patch:
rename desc->handler to desc->chip.
Originally i did not want to do this, because it's a big patch. But having
both "desc->handler", "desc->handle_irq" and "action->handler" caused a
large degree of confusion and made the code appear alot less clean than it
truly is.
I have also attempted a dual approach as well by introducing a
desc->chip alias - but that just wasnt robust enough and broke
frequently.
So lets get over with this quickly. The conversion was done automatically
via scripts and converts all the code in the kernel.
This renaming patch is the first one amongst the patches, so that the
remaining patches can stay flexible and can be merged and split up
without having some big monolithic patch act as a merge barrier.
[akpm@osdl.org: build fix]
[akpm@osdl.org: another build fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The TPAM isdn driver was removed in 2.6.12, but include/linux/isdn/tpam.h
was missed.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The proposed NFS key type uses its own method of passing key requests to
userspace (upcalling) rather than invoking /sbin/request-key. This is
because the responsible userspace daemon should already be running and will
be contacted through rpc_pipefs.
This patch permits the NFS filesystem to pass auxiliary data to the upcall
operation (struct key_type::request_key) so that the upcaller can use a
pre-existing communications channel more easily.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-By: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix some kernel-doc typos/spellos.
Use kernel-doc syntax in places where it was almost used.
Correct/add struct, struct field, and function param names where needed.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix all kernel-doc warnings in MTD headers and source files:
- add some missing struct fields;
- correct some function parameter names;
- use kernel-doc format for function doc. headers;
- nand_ecc.c contains only exported interfaces, no internal ones;
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
plist.h uses container_of, which is defined in kernel.h.
Include kernel.h in plist.h as the kernel.h include does not longer
happen automatically on all architectures.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds earlier initialization of spi_device.mode, as needed
on boards using nondefault chipselect polarity. An example would be
ones using the RS5C348 RTC without an external signal inverter between
the RTC chipselect and the SPI controller.
Without this mechanism, the first setup() call for that chip would
wrongly enable chips, corrupting transfers to/from other chips sharing
that SPI bus.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the controller FIFO cleared automatically on error we must not try
and drain it as this will hang some chips.
Based in concept on a broken patch from -mm some while back
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make a 1-bit bitfield unsigned (no space for sign bit).
Removes 24 sparse warnings from this one file:
include/linux/ac97_codec.h:262:13: error: dubious one-bit signed bitfield
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove 'active' field from tty buffer structure. This was added in 2.6.16
as part of a patch to make the new tty buffering SMP safe. This field is
unnecessary with the more intelligently written flush_to_ldisc that adds
receive_room handling.
Removing this field reverts to simpler logic where the tail buffer is
always the 'active' buffer, which should not be freed by flush_to_ldisc.
(active == buffer being filled with new data)
The result is simpler, smaller, and faster tty buffer code.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove TTY_DONT_FLIP tty flag. This flag was introduced in 2.1.X kernels
to prevent the N_TTY line discipline functions read_chan() and
n_tty_receive_buf() from running at the same time. 2.2.15 introduced
tty->read_lock to protect access to the N_TTY read buffer, which is the
only state requiring protection between these two functions.
The current TTY_DONT_FLIP implementation is broken for SMP, and is not
universally honored by drivers that send data directly to the line
discipline receive_buf function.
Because TTY_DONT_FLIP is not necessary, is broken in implementation, and is
not universally honored, it is removed.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Temporarily add EXPORT_UNUSED_SYMBOL and EXPORT_UNUSED_SYMBOL_GPL. These
will be used as a transition measure for symbols that aren't used in the
kernel and are on the way out. When a module uses such a symbol, a warning
is printk'd at modprobe time.
The main reason for removing unused exports is size: eacho export takes
roughly between 100 and 150 bytes of kernel space in the binary. This
patch gives users the option to immediately get this size gain via a config
option.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Same as with already do with the file operations: keep them in .rodata and
prevents people from doing runtime patching.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts ccf01ef7aa commit.
No idea how git managed this one: when I asked it to merge the odirect
topic branch it actually generated a patch which reverted the change.
Reverting the 'merge' will once again reveal Chuck's recent NFS/O_DIRECT
work to the world.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When the priority of a task, which is blocked on a lock, changes we must
propagate this change into the PI lock chain. Therefor the chain walk code
is changed to get rid of the references to current to avoid false positives
in the deadlock detector, as setscheduler might be called by a task which
holds the lock on which the task whose priority is changed is blocked.
Also add some comments about the get/put_task_struct usage to avoid
confusion.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds the actual pi-futex implementation, based on rt-mutexes.
[dino@in.ibm.com: fix an oops-causing race]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dinakar Guniguntala <dino@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
RT-mutex tester: scriptable tester for rt mutexes, which allows userspace
scripting of mutex unit-tests (and dynamic tests as well), using the actual
rt-mutex implementation of the kernel.
[akpm@osdl.org: fixlet]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Runtime debugging functionality for rt-mutexes.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Core functions for the rt-mutex subsystem.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add framework to boost/unboost the priority of RT tasks.
This consists of:
- caching the 'normal' priority in ->normal_prio
- providing a functions to set/get the priority of the task
- make sched_setscheduler() aware of boosting
The effective_prio() cleanups also fix a priority-calculation bug pointed out
by Andrey Gelman, in set_user_nice().
has_rt_policy() fix: Peter Williams <pwil3058@bigpond.net.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Andrey Gelman <agelman@012.net.il>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the priority-sorted list (plist) implementation.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add debug_check_no_locks_freed(), as a central inline to add
bad-lock-free-debugging functionality to.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We are pleased to announce "lightweight userspace priority inheritance" (PI)
support for futexes. The following patchset and glibc patch implements it,
ontop of the robust-futexes patchset which is included in 2.6.16-mm1.
We are calling it lightweight for 3 reasons:
- in the user-space fastpath a PI-enabled futex involves no kernel work
(or any other PI complexity) at all. No registration, no extra kernel
calls - just pure fast atomic ops in userspace.
- in the slowpath (in the lock-contention case), the system call and
scheduling pattern is in fact better than that of normal futexes, due to
the 'integrated' nature of FUTEX_LOCK_PI. [more about that further down]
- the in-kernel PI implementation is streamlined around the mutex
abstraction, with strict rules that keep the implementation relatively
simple: only a single owner may own a lock (i.e. no read-write lock
support), only the owner may unlock a lock, no recursive locking, etc.
Priority Inheritance - why, oh why???
-------------------------------------
Many of you heard the horror stories about the evil PI code circling Linux for
years, which makes no real sense at all and is only used by buggy applications
and which has horrible overhead. Some of you have dreaded this very moment,
when someone actually submits working PI code ;-)
So why would we like to see PI support for futexes?
We'd like to see it done purely for technological reasons. We dont think it's
a buggy concept, we think it's useful functionality to offer to applications,
which functionality cannot be achieved in other ways. We also think it's the
right thing to do, and we think we've got the right arguments and the right
numbers to prove that. We also believe that we can address all the
counter-arguments as well. For these reasons (and the reasons outlined below)
we are submitting this patch-set for upstream kernel inclusion.
What are the benefits of PI?
The short reply:
----------------
User-space PI helps achieving/improving determinism for user-space
applications. In the best-case, it can help achieve determinism and
well-bound latencies. Even in the worst-case, PI will improve the statistical
distribution of locking related application delays.
The longer reply:
-----------------
Firstly, sharing locks between multiple tasks is a common programming
technique that often cannot be replaced with lockless algorithms. As we can
see it in the kernel [which is a quite complex program in itself], lockless
structures are rather the exception than the norm - the current ratio of
lockless vs. locky code for shared data structures is somewhere between 1:10
and 1:100. Lockless is hard, and the complexity of lockless algorithms often
endangers to ability to do robust reviews of said code. I.e. critical RT
apps often choose lock structures to protect critical data structures, instead
of lockless algorithms. Furthermore, there are cases (like shared hardware,
or other resource limits) where lockless access is mathematically impossible.
Media players (such as Jack) are an example of reasonable application design
with multiple tasks (with multiple priority levels) sharing short-held locks:
for example, a highprio audio playback thread is combined with medium-prio
construct-audio-data threads and low-prio display-colory-stuff threads. Add
video and decoding to the mix and we've got even more priority levels.
So once we accept that synchronization objects (locks) are an unavoidable fact
of life, and once we accept that multi-task userspace apps have a very fair
expectation of being able to use locks, we've got to think about how to offer
the option of a deterministic locking implementation to user-space.
Most of the technical counter-arguments against doing priority inheritance
only apply to kernel-space locks. But user-space locks are different, there
we cannot disable interrupts or make the task non-preemptible in a critical
section, so the 'use spinlocks' argument does not apply (user-space spinlocks
have the same priority inversion problems as other user-space locking
constructs). Fact is, pretty much the only technique that currently enables
good determinism for userspace locks (such as futex-based pthread mutexes) is
priority inheritance:
Currently (without PI), if a high-prio and a low-prio task shares a lock [this
is a quite common scenario for most non-trivial RT applications], even if all
critical sections are coded carefully to be deterministic (i.e. all critical
sections are short in duration and only execute a limited number of
instructions), the kernel cannot guarantee any deterministic execution of the
high-prio task: any medium-priority task could preempt the low-prio task while
it holds the shared lock and executes the critical section, and could delay it
indefinitely.
Implementation:
---------------
As mentioned before, the userspace fastpath of PI-enabled pthread mutexes
involves no kernel work at all - they behave quite similarly to normal
futex-based locks: a 0 value means unlocked, and a value==TID means locked.
(This is the same method as used by list-based robust futexes.) Userspace uses
atomic ops to lock/unlock these mutexes without entering the kernel.
To handle the slowpath, we have added two new futex ops:
FUTEX_LOCK_PI
FUTEX_UNLOCK_PI
If the lock-acquire fastpath fails, [i.e. an atomic transition from 0 to TID
fails], then FUTEX_LOCK_PI is called. The kernel does all the remaining work:
if there is no futex-queue attached to the futex address yet then the code
looks up the task that owns the futex [it has put its own TID into the futex
value], and attaches a 'PI state' structure to the futex-queue. The pi_state
includes an rt-mutex, which is a PI-aware, kernel-based synchronization
object. The 'other' task is made the owner of the rt-mutex, and the
FUTEX_WAITERS bit is atomically set in the futex value. Then this task tries
to lock the rt-mutex, on which it blocks. Once it returns, it has the mutex
acquired, and it sets the futex value to its own TID and returns. Userspace
has no other work to perform - it now owns the lock, and futex value contains
FUTEX_WAITERS|TID.
If the unlock side fastpath succeeds, [i.e. userspace manages to do a TID ->
0 atomic transition of the futex value], then no kernel work is triggered.
If the unlock fastpath fails (because the FUTEX_WAITERS bit is set), then
FUTEX_UNLOCK_PI is called, and the kernel unlocks the futex on the behalf of
userspace - and it also unlocks the attached pi_state->rt_mutex and thus wakes
up any potential waiters.
Note that under this approach, contrary to other PI-futex approaches, there is
no prior 'registration' of a PI-futex. [which is not quite possible anyway,
due to existing ABI properties of pthread mutexes.]
Also, under this scheme, 'robustness' and 'PI' are two orthogonal properties
of futexes, and all four combinations are possible: futex, robust-futex,
PI-futex, robust+PI-futex.
glibc support:
--------------
Ulrich Drepper and Jakub Jelinek have written glibc support for PI-futexes
(and robust futexes), enabling robust and PI (PTHREAD_PRIO_INHERIT) POSIX
mutexes. (PTHREAD_PRIO_PROTECT support will be added later on too, no
additional kernel changes are needed for that). [NOTE: The glibc patch is
obviously inofficial and unsupported without matching upstream kernel
functionality.]
the patch-queue and the glibc patch can also be downloaded from:
http://redhat.com/~mingo/PI-futex-patches/
Many thanks go to the people who helped us create this kernel feature: Steven
Rostedt, Esben Nielsen, Benedikt Spranger, Daniel Walker, John Cooper, Arjan
van de Ven, Oleg Nesterov and others. Credits for related prior projects goes
to Dirk Grambow, Inaky Perez-Gonzalez, Bill Huey and many others.
Clean up the futex code, before adding more features to it:
- use u32 as the futex field type - that's the ABI
- use __user and pointers to u32 instead of unsigned long
- code style / comment style cleanups
- rename hash-bucket name from 'bh' to 'hb'.
I checked the pre and post futex.o object files to make sure this
patch has no code effects.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Jakub Jelinek <jakub@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sysfs entries 'sched_mc_power_savings' and 'sched_smt_power_savings' in
/sys/devices/system/cpu/ control the MC/SMT power savings policy for the
scheduler.
Based on the values (1-enable, 0-disable) for these controls, sched groups
cpu power will be determined for different domains. When power savings
policy is enabled and under light load conditions, scheduler will minimize
the physical packages/cpu cores carrying the load and thus conserving
power(with a perf impact based on the workload characteristics... see OLS
2005 CMP kernel scheduler paper for more details..)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Con Kolivas <kernel@kolivas.org>
Cc: "Chen, Kenneth W" <kenneth.w.chen@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Try to handle mem allocation failures in build_sched_domains by bailing out
and cleaning up thus-far allocated memory. The patch has a direct consequence
that we disable load balancing completely (even at sibling level) upon *any*
memory allocation failure.
[Lee.Schermerhorn@hp.com: bugfix]
Signed-off-by: Srivatsa Vaddagir <vatsa@in.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Problem:
The introduction of separate run queues per CPU has brought with it "nice"
enforcement problems that are best described by a simple example.
For the sake of argument suppose that on a single CPU machine with a
nice==19 hard spinner and a nice==0 hard spinner running that the nice==0
task gets 95% of the CPU and the nice==19 task gets 5% of the CPU. Now
suppose that there is a system with 2 CPUs and 2 nice==19 hard spinners and
2 nice==0 hard spinners running. The user of this system would be entitled
to expect that the nice==0 tasks each get 95% of a CPU and the nice==19
tasks only get 5% each. However, whether this expectation is met is pretty
much down to luck as there are four equally likely distributions of the
tasks to the CPUs that the load balancing code will consider to be balanced
with loads of 2.0 for each CPU. Two of these distributions involve one
nice==0 and one nice==19 task per CPU and in these circumstances the users
expectations will be met. The other two distributions both involve both
nice==0 tasks being on one CPU and both nice==19 being on the other CPU and
each task will get 50% of a CPU and the user's expectations will not be
met.
Solution:
The solution to this problem that is implemented in the attached patch is
to use weighted loads when determining if the system is balanced and, when
an imbalance is detected, to move an amount of weighted load between run
queues (as opposed to a number of tasks) to restore the balance. Once
again, the easiest way to explain why both of these measures are necessary
is to use a simple example. Suppose that (in a slight variation of the
above example) that we have a two CPU system with 4 nice==0 and 4 nice=19
hard spinning tasks running and that the 4 nice==0 tasks are on one CPU and
the 4 nice==19 tasks are on the other CPU. The weighted loads for the two
CPUs would be 4.0 and 0.2 respectively and the load balancing code would
move 2 tasks resulting in one CPU with a load of 2.0 and the other with
load of 2.2. If this was considered to be a big enough imbalance to
justify moving a task and that task was moved using the current
move_tasks() then it would move the highest priority task that it found and
this would result in one CPU with a load of 3.0 and the other with a load
of 1.2 which would result in the movement of a task in the opposite
direction and so on -- infinite loop. If, on the other hand, an amount of
load to be moved is calculated from the imbalance (in this case 0.1) and
move_tasks() skips tasks until it find ones whose contributions to the
weighted load are less than this amount it would move two of the nice==19
tasks resulting in a system with 2 nice==0 and 2 nice=19 on each CPU with
loads of 2.1 for each CPU.
One of the advantages of this mechanism is that on a system where all tasks
have nice==0 the load balancing calculations would be mathematically
identical to the current load balancing code.
Notes:
struct task_struct:
has a new field load_weight which (in a trade off of space for speed)
stores the contribution that this task makes to a CPU's weighted load when
it is runnable.
struct runqueue:
has a new field raw_weighted_load which is the sum of the load_weight
values for the currently runnable tasks on this run queue. This field
always needs to be updated when nr_running is updated so two new inline
functions inc_nr_running() and dec_nr_running() have been created to make
sure that this happens. This also offers a convenient way to optimize away
this part of the smpnice mechanism when CONFIG_SMP is not defined.
int try_to_wake_up():
in this function the value SCHED_LOAD_BALANCE is used to represent the load
contribution of a single task in various calculations in the code that
decides which CPU to put the waking task on. While this would be a valid
on a system where the nice values for the runnable tasks were distributed
evenly around zero it will lead to anomalous load balancing if the
distribution is skewed in either direction. To overcome this problem
SCHED_LOAD_SCALE has been replaced by the load_weight for the relevant task
or by the average load_weight per task for the queue in question (as
appropriate).
int move_tasks():
The modifications to this function were complicated by the fact that
active_load_balance() uses it to move exactly one task without checking
whether an imbalance actually exists. This precluded the simple
overloading of max_nr_move with max_load_move and necessitated the addition
of the latter as an extra argument to the function. The internal
implementation is then modified to move up to max_nr_move tasks and
max_load_move of weighted load. This slightly complicates the code where
move_tasks() is called and if ever active_load_balance() is changed to not
use move_tasks() the implementation of move_tasks() should be simplified
accordingly.
struct sched_group *find_busiest_group():
Similar to try_to_wake_up(), there are places in this function where
SCHED_LOAD_SCALE is used to represent the load contribution of a single
task and the same issues are created. A similar solution is adopted except
that it is now the average per task contribution to a group's load (as
opposed to a run queue) that is required. As this value is not directly
available from the group it is calculated on the fly as the queues in the
groups are visited when determining the busiest group.
A key change to this function is that it is no longer to scale down
*imbalance on exit as move_tasks() uses the load in its scaled form.
void set_user_nice():
has been modified to update the task's load_weight field when it's nice
value and also to ensure that its run queue's raw_weighted_load field is
updated if it was runnable.
From: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
With smpnice, sched groups with highest priority tasks can mask the imbalance
between the other sched groups with in the same domain. This patch fixes some
of the listed down scenarios by not considering the sched groups which are
lightly loaded.
a) on a simple 4-way MP system, if we have one high priority and 4 normal
priority tasks, with smpnice we would like to see the high priority task
scheduled on one cpu, two other cpus getting one normal task each and the
fourth cpu getting the remaining two normal tasks. but with current
smpnice extra normal priority task keeps jumping from one cpu to another
cpu having the normal priority task. This is because of the
busiest_has_loaded_cpus, nr_loaded_cpus logic.. We are not including the
cpu with high priority task in max_load calculations but including that in
total and avg_load calcuations.. leading to max_load < avg_load and load
balance between cpus running normal priority tasks(2 Vs 1) will always show
imbalanace as one normal priority and the extra normal priority task will
keep moving from one cpu to another cpu having normal priority task..
b) 4-way system with HT (8 logical processors). Package-P0 T0 has a
highest priority task, T1 is idle. Package-P1 Both T0 and T1 have 1 normal
priority task each.. P2 and P3 are idle. With this patch, one of the
normal priority tasks on P1 will be moved to P2 or P3..
c) With the current weighted smp nice calculations, it doesn't always make
sense to look at the highest weighted runqueue in the busy group..
Consider a load balance scenario on a DP with HT system, with Package-0
containing one high priority and one low priority, Package-1 containing one
low priority(with other thread being idle).. Package-1 thinks that it need
to take the low priority thread from Package-0. And find_busiest_queue()
returns the cpu thread with highest priority task.. And ultimately(with
help of active load balance) we move high priority task to Package-1. And
same continues with Package-0 now, moving high priority task from package-1
to package-0.. Even without the presence of active load balance, load
balance will fail to balance the above scenario.. Fix find_busiest_queue
to use "imbalance" when it is lightly loaded.
[kernel@kolivas.org: sched: store weighted load on up]
[kernel@kolivas.org: sched: add discrete weighted cpu load function]
[suresh.b.siddha@intel.com: sched: remove dead code]
Signed-off-by: Peter Williams <pwil3058@bigpond.com.au>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: "Chen, Kenneth W" <kenneth.w.chen@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Con Kolivas <kernel@kolivas.org>
Cc: John Hawkes <hawkes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use of dev_dbg() and friends is considered good practice. dev_dbg() needs a
struct device *devp, but nsc_gpio is only a helper module, so it doesnt
have/need its own. To provide devp to the user-modules (scx200 & pc8736x
_gpio), we add it to the vtable, and set it during init.
Also squeeze nsc_gpio_dump()'s format a little.
[ 199.259879] pc8736x_gpio.0: io09: 0x0044 TS OD PUE EDGE LO DEBOUNCE
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that the read(), write() file-ops are dispatching gpio-ops via the vtable,
they are generic, and can be moved 'verbatim' to the nsc_gpio common-support
module. After the move, various symbols are renamed to update 'scx200_' to
'nsc_', and headers are adjusted accordingly.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Abstract the gpio operations into a new nsc_gpio_ops vtable.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Per kernel headers, device minor numbers are unsigned ints. Do the same in
this driver.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
GPIO SUPPORT FOR SCx200 & PC8736x
The patch-set reworks the 2.4 vintage scx200_gpio driver for modern 2.6, and
refactors GPIO support to reuse it in a new driver for the GPIO on PC-8736x
chips. Its handy for the Soekris.com net-4801, which has both chips.
These patches have been seen recently on Kernel-Mentors, and then
Kernel-Newbies ML, where Jesper Juhl kindly reviewed it. His feedback has
been incorporated. Thanks Jesper !
Its also gone to soekris-tech@soekris.com for possible testing by linux folks,
I've gotten 1 promise so far. Theyre mostly BSD folk over there, but we'll
see..
Device-file & Sysfs
The driver preserves the existing device-file interface, including the
write/cmd set, but adds v to 'view' the pin-settings & configs by inducing,
via gpio_dump(), a dev_info() call. Its a fairly crappy way to get status,
but it sticks to the syslog approach, conservatively.
Allowing users to voluntarily trigger logging is good, it gives them a
familiar way to confirm their app's control & use of the pins, and I've thus
reduced the pin-mode-updates from dev_info to dev_dbg.
I've recently bolted on a proto sysfs interface for both new drivers. Im not
including those patches here; they (the patch + doc-pre-patch) are still quite
raw (and unreviewed on KNML), and since they 'invent' a convention for GPIO, a
proper vetting is needed. Since this patchset is much bigger than my previous
ones, Id like to keep things simpler, and address it 1st, before bolting on
more stuff.
The driver-split
The Geode CPU and the PC-87366 Super-IO chip have GPIO units which share a
common pin-architecture (same pin features, with same bits controlling), but
with different addressing mechanics and port organizations.
The vintage driver expresses the pin capabilities with pin-mode commands
[OoPpTt],etc that change the pin configurations, and since the 2 chips share
pin-arch, we can reuse the read(), write() commands, once the implementation
is suitably adjusted.
The patchset adds a vtable: struct nsc_gpio_ops, to abstract the existing gpio
operations, then adjusts fileops.write() code to invoke operations via that
vtable. Driver specific open()s set private_data to the vtable so its
available for use by write().
The vtable gets the gpio_dump() too, since its user-friendly, and (could be
construed as) part of the current device-file interface. To support use of
dev_dbg() in write() & _dump(), the vtable gets a dev ptr too, set by both
scx200 & pc8736x _gpio drivers.
heres how the pins are presented in syslog:
[ 1890.176223] scx200_gpio.0: io00: 0x0044 TS OD PUE EDGE LO DEBOUNCE
[ 1890.287223] scx200_gpio.0: io01: 0x0003 OE PP PUD EDGE LO
nsc_gpio.c: new file is new home of several file-ops methods, which are
modified to get their vtable from filp->private_data, and use it where needed.
scx200_gpio.c: keeps some of its existing gpio routines, but now wires them up
via the vtable (they're invoked by nsc_gpio.c:nsc_gpio_write() thru this
vtable). A driver-spcific open() initializes filp->private_data with the
vtable.
Once the split is clean, and the scx200_gpio driver is working, we copy and
modify the function and variable names, and rework the access-method bodies
for the different addressing scheme.
Heres a working overview of the patchset:
# series file for GPIO
# Spring Cleaning
gpio-scx/patch.preclean # scripts/Lindent fixes, editor-ctrl comments
# API Modernization
gpio-scx/patch.api26 # what I learned from LDD3
gpio-scx/patch.platform-dev-2 # get pdev, support for dev_dbg()
gpio-scx/patch.unsigned-minor # fix to match std practice
# Debuggability
gpio-scx/patch.dump-diet # shrink gpio_dump()
gpio-scx/patch.viewpins # add new 'command' to call dump()
gpio-scx/patch.init-refactor # pull shadow-register init to sub
# Access-Abstraction (add vtable)
gpio-scx/patch.access-vtable # introduce nsg_gpio_ops vtable, w dump
gpio-scx/patch.vtable-calls # add & use the vtable in scx200_gpio
gpio-scx/patch.nscgpio-shell # add empty driver for common-fops
# move code under abstraction
gpio-scx/patch.migrate-fops # move file-ops methods from scx200_gpio
gpio-scx/patch.common-dump # mv scx200.c:scx200_gpio_dump() to nsc_gpio.c
gpio-scx/patch.add-pc8736x-gpio # add new driver, like old, w chip adapt
# gpio-scx/patch.add-DEBUG # enable all dev_dbg()s
# Cleanups
# finish printk -> dev_dbg() etc
gpio-scx/patch.pdev-pc8736x # new drvr needs pdev too,
gpio-scx/patch.devdbg-nscgpio # add device to 'vtable', use in dev_dbg()
# gpio-scx/patch.pin-config-view # another 'c' 'command'
# gpio-scx/quiet-getset # take out excess dbg stuff (pretty quiet
now)
gpio-scx/patch.shadow-current # imitate scx200_gpio's shadow regs in
pc87*
# post KMentors-post patches ..
gpio-scx/patch.mutexes # use mutexes for config-locks
gpio-scx/patch.viewpins-values # extend dump to obsolete separate 'c' cmd
gpio-scx/patch.kconfig # add stuff for kbuild
# TBC
# combine api26 with pdev, which is just one step.
# merge c&v commands to single do-all-fn
# delay viewpins, dump-diet should also un-ifdef it too.
diff.sys-gpio-rollup-1
This patch:
Removed editor format-control comments, and used scripts/Lindent to clean up
whitespace, then deleted the bogus chunks :-(
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define new macros register_hotcpu_notifier() and unregister_hotcpu_notifier()
that redefines register_cpu_notifier() and unregister_cpu_notifier() for use
only when HOTPLUG_CPU is defined.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CPUs come online only at init time (unless CONFIG_HOTPLUG_CPU is defined).
So, cpu_notifier functionality need to be available only at init time.
This patch makes register_cpu_notifier() available only at init time, unless
CONFIG_HOTPLUG_CPU is defined.
This patch exports register_cpu_notifier() and unregister_cpu_notifier() only
if CONFIG_HOTPLUG_CPU is defined.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add operations for the call_rcu_bh() variant of RCU. Also add an
rcu_batches_completed_bh() function, which is needed by rcutorture.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We include config.h on the compiler command line. There's no need for it
to be included again.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- add a proper prototype for the following global function:
- buffer_init()
- make the following needlessly global function static:
- end_buffer_async_write()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add more poison values to include/linux/poison.h. It's not clear to me
whether some others should be added or not, so I haven't added any of
these:
./include/linux/libata.h:#define ATA_TAG_POISON 0xfafbfcfdU
./arch/ppc/8260_io/fcc_enet.c:1918: memset((char *)(&(immap->im_dprambase[(mem_addr+64)])), 0x88, 32);
./drivers/usb/mon/mon_text.c:429: memset(mem, 0xe5, sizeof(struct mon_event_text));
./drivers/char/ftape/lowlevel/ftape-ctl.c:738: memset(ft_buffer[i]->address, 0xAA, FT_BUFF_SIZE);
./drivers/block/sx8.c:/* 0xf is just arbitrary, non-zero noise; this is sorta like poisoning */
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update two drivers to use poison.h.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Localize poison values into one header file for better documentation and
easier/quicker debugging and so that the same values won't be used for
multiple purposes.
Use these constants in core arch., mm, driver, and fs code.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Matt Mackall <mpm@selenic.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the i386 VDSO down into a vma and thus randomize it.
Besides the security implications, this feature also helps debuggers, which
can COW a vma-backed VDSO just like a normal DSO and can thus do
single-stepping and other debugging features.
It's good for hypervisors (Xen, VMWare) too, which typically live in the same
high-mapped address space as the VDSO, hence whenever the VDSO is used, they
get lots of guest pagefaults and have to fix such guest accesses up - which
slows things down instead of speeding things up (the primary purpose of the
VDSO).
There's a new CONFIG_COMPAT_VDSO (default=y) option, which provides support
for older glibcs that still rely on a prelinked high-mapped VDSO. Newer
distributions (using glibc 2.3.3 or later) can turn this option off. Turning
it off is also recommended for security reasons: attackers cannot use the
predictable high-mapped VDSO page as syscall trampoline anymore.
There is a new vdso=[0|1] boot option as well, and a runtime
/proc/sys/vm/vdso_enabled sysctl switch, that allows the VDSO to be turned
on/off.
(This version of the VDSO-randomization patch also has working ELF
coredumping, the previous patch crashed in the coredumping code.)
This code is a combined work of the exec-shield VDSO randomization
code and Gerd Hoffmann's hypervisor-centric VDSO patch. Rusty Russell
started this patch and i completed it.
[akpm@osdl.org: cleanups]
[akpm@osdl.org: compile fix]
[akpm@osdl.org: compile fix 2]
[akpm@osdl.org: compile fix 3]
[akpm@osdl.org: revernt MAXMEM change]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Cc: Gerd Hoffmann <kraxel@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Goto-san's patch, we can add new pgdat/node at runtime. I'm now
considering node-hot-add with cpu + memory on ACPI.
I found acpi container, which describes node, could evaluate cpu before
memory. This means cpu-hot-add occurs before memory hot add.
In most part, cpu-hot-add doesn't depend on node hot add. But register_cpu(),
which creates symbolic link from node to cpu, requires that node should be
onlined before register_cpu(). When a node is onlined, its pgdat should be
there.
This patch-set holds off creating symbolic link from node to cpu
until node is onlined.
This removes node arguments from register_cpu().
Now, register_cpu() requires 'struct node' as its argument. But the array of
struct node is now unified in driver/base/node.c now (By Goto's node hotplug
patch). We can get struct node in generic way. So, this argument is not
necessary now.
This patch also guarantees add cpu under node only when node is onlined. It
is necessary for node-hot-add vs. cpu-hot-add patch following this.
Moreover, register_cpu calculates cpu->node_id by cpu_to_node() without regard
to its 'struct node *root' argument. This patch removes it.
Also modify callers of register_cpu()/unregister_cpu, whose args are changed
by register-cpu-remove-node-struct patch.
[Brice.Goglin@ens-lyon.org: fix it]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a patch to allocate pgdat and per node data area for ia64. The size
for them can be calculated by compute_pernodesize().
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is to refresh node_data[] array for ia64. As I mentioned previous
patches, ia64 has copies of information of pgdat address array on each node as
per node data.
At v2 of node_add, this function used stop_machine_run() to update them. (I
wished that they were copied safety as much as possible.) But, in this patch,
this arrays are just copied simply, and set node_online_map bit after
completion of pgdat initialization.
So, kernel must touch NODE_DATA() macro after checking node_online_map().
(Current code has already done it.) This is more simple way for just
hot-add.....
Note : It will be problem when hot-remove will occur,
because, even if online_map bit is set, kernel may
touch NODE_DATA() due to race condition. :-(
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When new node becomes enable by hot-add, new sysfs file must be created for
new node. So, if new node is enabled by add_memory(), register_one_node() is
called to create it. In addition, I386's arch_register_node() and a part of
register_nodes() of powerpc are consolidated to register_one_node() as a
generic_code().
This is tested by Tiger4(IPF) with node hot-plug emulation.
Signed-off-by: Keiichiro Tokunaga <tokuanga.keiich@jp.fujitsu.com>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch allows hot-add memory which is not aligned to section.
Now, hot-added memory has to be aligned to section size. Considering big
section sized archs, this is not useful.
When hot-added memory is registerd as iomem resoruce by iomem resource
patch, we can make use of that information to detect valid memory range.
Note: With this, not-aligned memory can be registerd. To allow hot-add
memory with holes, we have to do more work around add_memory().
(It doesn't allows add memory to already existing mem section.)
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When node is hot-added, kswapd for the node should start. This export kswapd
start function as kswapd_run() to use at add_memory().
[akpm@osdl.org: daemonize() isn't needed when using the kthread API]
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Refresh NODE_DATA() for generic archs. In this case, NODE_DATA(nid) ==
node_data[nid]. node_data[] is array of address of pgdat. So, refresh is
quite simple.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For node hotplug, basically we have to allocate new pgdat. But, there are
several types of implementations of pgdat.
1. Allocate only pgdat.
This style allocate only pgdat area.
And its address is recorded in node_data[].
It is most popular style.
2. Static array of pgdat
In this case, all of pgdats are static array.
Some archs use this style.
3. Allocate not only pgdat, but also per node data.
To increase performance, each node has copy of some data as
a per node data. So, this area must be allocated too.
Ia64 is this style. Ia64 has the copies of node_data[] array
on each per node data to increase performance.
In this series of patches, treat (1) as generic arch.
generic archs can use generic function. (2) and (3) should have
its own if necessary.
This patch defines pgdat allocator.
Updating NODE_DATA() macro function is in other patch.
Signed-off-by: Yasonori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is to find node id from acpi's handle of memory_device in DSDT. _PXM for
the new node can be found by acpi_get_pxm() by using new memory's handle. So,
node id can be found by pxm_to_nid_map[].
This patch becomes simpler than v2 of node hot-add patch.
Because old add_memory() function doesn't have node id parameter.
So, kernel must find its handle by physical address via DSDT again.
But, v3 just give node id to add_memory() now.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the name of old add_memory() to arch_add_memory. And use node id to
get pgdat for the node at NODE_DATA().
Note: Powerpc's old add_memory() is defined as __devinit. However,
add_memory() is usually called only after bootup.
I suppose it may be redundant. But, I'm not well known about powerpc.
So, I keep it. (But, __meminit is better at least.)
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce the Kconfig entry and actually switch to a 64bit value, if
wanted, for resource_size_t.
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
But do not change it from what it currently is (unsigned long)
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- When xdatum is removed, a new xdatum with 'delete marker' is
written. (version==0xffffffff means 'delete marker')
- When xref is removed, a new xref with 'delete marker' is written.
(odd-numbered xseqno means 'delete marker')
- delete_xattr_(datum/xref)_delay() are new deletion functions
are added. We can only use them if we can detect the target
obsolete xdatum/xref as a orphan or errir one.
(e.g when inode deletion, or detecting crc error)
[1/3] jffs2-xattr-v6-01-delete_marker.patch
Signed-off-by: KaiGai Kohei <kaigai@ak.jp.nec.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
so that userspace can be notified of dock and undock events.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Implement ata_port_max_devices(). This function returns the number of
possible devices on a port. This will be used by new PM
implementation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Andrew Morton <akpm@osdl.org>
s390:
In file included from drivers/scsi/libata-bmdma.c:39: include/linux/libata.h:391: error: field 'sgent' has incomplete type
include/linux/libata.h:392: error: field 'pad_sgent' has incomplete type
include/linux/libata.h: In function 'ata_sg_is_last': include/linux/libata.h:849: error: arithmetic on pointer to an incomplete type
include/linux/libata.h:849: error: arithmetic on pointer to an incomplete type
include/linux/libata.h: In function 'ata_qc_next_sg':
include/linux/libata.h:869: error: increment of pointer to unknown structure
include/linux/libata.h:869: error: arithmetic on pointer to an incomplete type
include/linux/libata.h:869: error: arithmetic on pointer to an incomplete type
include/linux/libata.h:869: error: arithmetic on pointer to an incomplete type
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Partially revert 74d0a988d3aa359b6b8a8536c8cb92cce02ca5d5:
[PATCH] PCI: Move various PCI IDs to header file
libata policy is to avoid use of named PCI device ID constants.
These are often single-use constants, which have little value over
direct numeric constants save for constant include/linux/pci_ids.h
patching/merging headaches.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
typo fixes
Clean up 'inline is not at beginning' warnings for usb storage
Storage class should be first
i386: Trivial typo fixes
ixj: make ixj_set_tone_off() static
spelling fixes
fix paniced->panicked typos
Spelling fixes for Documentation/atomic_ops.txt
move acknowledgment for Mark Adler to CREDITS
remove the bouncing email address of David Campbell
I've always found this flag confusing. Now that devfs is no longer around, it
has been renamed, and the documentation for when this flag should be used has
been updated.
Also fixes all drivers that use this flag.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the first patch in a series of patches that removes devfs
support from the kernel. This patch removes the core devfs code, and
its private header file.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit c7b2eff059.
Hugh Dickins explains:
"It seems too little tested: "losetup -d /dev/loop0" fails with
EINVAL because nothing sets lo_thread; but even when you patch
loop_thread() to set lo->lo_thread = current, it can't survive
more than a few dozen iterations of the loop below (with a tmpfs
mounted on /tst):
j=0
cp /dev/zero /tst
while :
do
let j=j+1
echo "Doing pass $j"
losetup /dev/loop0 /tst/zero
mkfs -t ext2 -b 1024 /dev/loop0 >/dev/null 2>&1
mount -t ext2 /dev/loop0 /mnt
umount /mnt
losetup -d /dev/loop0
done
it collapses with failed ioctl then BUG_ON(!bio).
I think the original lo_done completion was more subtle and safe
than the kthread conversion has allowed for."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits)
kbuild: trivial fixes in Makefile
kbuild: adding symbols in Kconfig and defconfig to TAGS
kbuild: replace abort() with exit(1)
kbuild: support for %.symtypes files
kbuild: fix silentoldconfig recursion
kbuild: add option for stripping modules while installing them
kbuild: kill some false positives from modpost
kbuild: export-symbol usage report generator
kbuild: fix make -rR breakage
kbuild: append -dirty for updated but uncommited changes
kbuild: append git revision for all untagged commits
kbuild: fix module.symvers parsing in modpost
kbuild: ignore make's built-in rules & variables
kbuild: bugfix with initramfs
kbuild: modpost build fix
kbuild: check license compatibility when building modules
kbuild: export-type enhancement to modpost.c
kbuild: add dependency on kernel.release to the package targets
kbuild: `make kernelrelease' speedup
kconfig: KCONFIG_OVERWRITECONFIG
...
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (4227): Update this driver for recent header file movement.
V4L/DVB (4223): Add V4L2_CID_MPEG_STREAM_VBI_FMT control
V4L/DVB (4222): Always switch tuner mode when calling VIDIOC_S_FREQUENCY.
V4L/DVB (4221): Add HM12 YUV format define.
V4L/DVB (4219): Av7110: analog sound output of DVB-C rev 2.3
V4L/DVB (4217): Fix a misplaced closing bracket/else, which caused swzigzag not to be called
V4L/DVB (4215): Make VIDEO_CX88_BLACKBIRD a separate build option
V4L/DVB (4214): Make VIDEO_CX2341X a selectable build option
V4L/DVB (4213): Cx88: cleanups
V4L/DVB (4211): Fix an Oops for all fe that have get_frontend_algo == NULL
In timekeeping code, one often does need to use conversion constants. Naming
these leads to code that's easier to understand, showing the reader between
which units the conversion is made.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add proper conditionals to be able to build with CONFIG_MODULES=n.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If no unwinding is possible at all for a certain exception instance,
fall back to the old style call trace instead of not showing any trace
at all.
Also, allow setting the stack trace mode at the command line.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These are the generic bits needed to enable reliable stack traces based
on Dwarf2-like (.eh_frame) unwind information. Subsequent patches will
enable x86-64 and i386 to make use of this.
Thanks to Andi Kleen and Ingo Molnar, who pointed out several possibilities
for improvement.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sometimes e.g. with crashme the compat layer warnings can be noisy.
Add a way to turn them off by gating all output through compat_printk
that checks a global sysctl. The default is not changed.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
[IOAT]: Do not dereference THIS_MODULE directly to set unsafe.
[NETROM]: Fix possible null pointer dereference.
[NET] netpoll: break recursive loop in netpoll rx path
[NET] netpoll: don't spin forever sending to stopped queues
[IRDA]: add some IBM think pads
[ATM]: atm/mpc.c warning fix
[NET]: skb_find_text ignores to argument
[NET]: make net/core/dev.c:netdev_nit static
[NET]: Fix GSO problems in dev_hard_start_xmit()
[NET]: Fix CHECKSUM_HW GSO problems.
[TIPC]: Fix incorrect correction to discovery timer frequency computation.
[TIPC]: Get rid of dynamically allocated arrays in broadcast code.
[TIPC]: Fixed link switchover bugs
[TIPC]: Enhanced & cleaned up system messages; fixed 2 obscure memory leaks.
[TIPC]: First phase of assert() cleanup
[TIPC]: Disallow config operations that aren't supported in certain modes.
[TIPC]: Fixed memory leak in tipc_link_send() when destination is unreachable
[TIPC]: Added missing warning for out-of-memory condition
[TIPC]: Withdrawing all names from nameless port now returns success, not error
[TIPC]: Optimized argument validation done by connect().
...
- record the 'event' count on each individual device (they
might sometimes be slightly different now)
- add a new value for 'sb_dirty': '3' means that the super
block only needs to be updated to record a clean<->dirty
transition.
- Prefer odd event numbers for dirty states and even numbers
for clean states
- Using all the above, don't update the superblock on
a spare device if the update is just doing a clean-dirty
transition. To accomodate this, a transition from
dirty back to clean might now decrement the events counter
if nothing else has changed.
The net effect of this is that spare drives will not see any IO requests
during normal running of the array, so they can go to sleep if that is what
they want to do.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If md is asked to store a bitmap in a file, it tries to hold onto the page
cache pages for that file, manipulate them directly, and call a cocktail of
operations to write the file out. I don't believe this is a supportable
approach.
This patch changes the approach to use the same approach as swap files. i.e.
bmap is used to enumerate all the block address of parts of the file and we
write directly to those blocks of the device.
swapfile only uses parts of the file that provide a full pages at contiguous
addresses. We don't have that luxury so we have to cope with pages that are
non-contiguous in storage. To handle this we attach buffers to each page, and
store the addresses in those buffers.
With this approach the pagecache may contain data which is inconsistent with
what is on disk. To alleviate the problems this can cause, md invalidates the
pagecache when releasing the file. If the file is to be examined while the
array is active (a non-critical but occasionally useful function), O_DIRECT io
must be used. And new version of mdadm will have support for this.
This approach simplifies a lot of code:
- we no longer need to keep a list of pages which we need to wait for,
as the b_endio function can keep track of how many outstanding
writes there are. This saves a mempool.
- -EAGAIN returns from write_page are no longer possible (not sure if
they ever were actually).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md/bitmap currently has a separate thread to wait for writes to the bitmap
file to complete (as we cannot get a callback on that action).
However this isn't needed as bitmap_unplug is called from process context and
waits for the writeback thread to do it's work. The same result can be
achieved by doing the waiting directly in bitmap_unplug.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes the needlessly global md_print_devices() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The "industry standard" DDF format allows for a stripe/offset layout where
data is duplicated on different stripes. e.g.
A B C D
D A B C
E F G H
H E F G
(columns are drives, rows are stripes, LETTERS are chunks of data).
This is similar to raid10's 'far' mode, but not quite the same. So enhance
'far' mode with a 'far/offset' option which follows the layout of DDFs
stripe/offset.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For a while we have had checkpointing of resync. The version-1 superblock
allows recovery to be checkpointed as well, and this patch implements that.
Due to early carelessness we need to add a feature flag to signal that the
recovery_offset field is in use, otherwise older kernels would assume that a
partially recovered array is in fact fully recovered.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a lot of commonality between raid5.c and raid6main.c. This patches
merges both into one module called raid456. This saves a lot of code, and
paves the way for online raid5->raid6 migrations.
There is still duplication, e.g. between handle_stripe5 and handle_stripe6.
This will probably be cleaned up later.
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The largest chunk size the code can support without substantial surgery is
2^30 bytes, so make that the limit instead of an arbitrary 4Meg. Some day,
the 'chunksize' should change to a sector-shift instead of a byte-count. Then
no limit would be needed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tidy device-mapper error messages to include context information
automatically.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If you misuse the device-mapper interface (or there's a bug in your userspace
tools) it's possible to end up with 'unlinked' mapped devices that cannot be
removed until you reboot (along with uninterruptible processes).
This patch prevents you from removing a device that is still open.
It introduces dm_lock_for_deletion() which is called when a device is about to
be removed to ensure that nothing has it open and nothing further can open it.
It uses a private open_count for this which also lets us remove one of the
problematic bdget_disk() calls elsewhere.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a library function dm_create_error_table() to create a table that rejects
any I/O sent to a device with EIO.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move definitions of core device-mapper functions for manipulating mapped
devices and their tables to <linux/device-mapper.h> advertising their
availability for use elsewhere in the kernel.
Protect the contents of device-mapper.h with ifdef __KERNEL__. And throw
in a few formatting clean-ups and extra comments.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds idr_replace() to replace an existing pointer in a single
operation.
Device-mapper will use this to update the pointer it stored against a given
id.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The control for binding/unbinding is moved from fbcon to the console layer.
Thus the fbcon sysfs attributes, attach and detach, are also gone.
1. Add a notifier event that tells fbcon if a framebuffer driver has been
unregistered. If no registered driver remains, fbcon will unregister
itself from the console layer.
2. Replaced calls to give_up_console() with unregister_con_driver().
3. Still use take_over_console() instead of register_con_driver() to
maintain compatibility
4. Respect the parameter first_fb_vc and last_fb_vc instead of using 0 and
MAX_NR_CONSOLES - 1. These parameters are settable by the user.
5. When fbcon is completely unbound from the console layer, fbcon will
also release (iow, decrement module reference counts to zero) all fbdev
drivers. In other words, a bind or unbind request from the console layer
will propagate down to the framebuffer drivers.
6. If fbcon is not bound to the console, it will ignore all notifier
events (except driver registration and unregistration) and all sysfs
requests.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The framebuffer console is now able to dynamically bind and unbind from the VT
console layer. Due to the way the VT console layer works, the drivers
themselves decide when to bind or unbind. However, it was decided that
binding must be controlled, not by the drivers themselves, but by the VT
console layer. With this, dynamic binding is possible for all VT console
drivers, not just fbcon.
Thus, the VT console layer will impose the following to all VT console
drivers:
- all registered VT console drivers will be entered in a private list
- drivers can register themselves to the VT console layer, but they cannot
decide when to bind or unbind. (Exception: To maintain backwards
compatibility, take_over_console() will automatically bind the driver after
registration.)
- drivers can remove themselves from the list by unregistering from the VT
console layer. A prerequisite for unregistration is that the driver must not
be bound.
The following functions are new in the vt.c:
register_con_driver() - public function, this function adds the VT console
driver to an internal list maintained by the VT console
bind_con_driver() - private function, it binds the driver to the console
take_over_console() is changed to call register_con_driver() followed by a
bind_con_driver(). This is the only time drivers can decide when to bind to
the VT layer. This is to maintain backwards compatibility.
unbind_con_driver() - private function, it unbinds the driver from its
console. The vacated consoles will be taken over by the default boot console
driver.
unregister_con_driver() - public function, removes the driver from the
internal list maintained by the VT console. It will only succeed if the
driver is currently unbound.
con_is_bound() checks if the driver is currently bound or not
give_up_console() is just a wrapper to unregister_con_driver().
There are also 3 additional functions meant to be called only by the tty layer
for sysfs control:
vt_bind() - calls bind_con_driver()
vt_unbind() - calls unbind_con_driver()
vt_show_drivers() - shows the list of registered drivers
Most VT console drivers will continue to work as is, but might have problems
when unbinding or binding which should be fixable with minimal changes.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order for this feature to work, an interface will be needed. The most
appropriate is sysfs. However, the framebuffer console has no sysfs entry
yet. This will create a sysfs class device entry for fbcon under
/sys/class/graphics.
Add a class_device entry 'fbcon' under class 'graphics'. Console-specific
attributes which where previously under class/graphics/fb[x] are moved to
class/graphics/fbcon. These attributes, 'con_rotate' and 'con_rotate_all',
are also renamed to 'rotate' and 'rotate_all' respectively.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With this patch zap_process() sets SIGNAL_GROUP_EXIT while sending SIGKILL to
the thread group. This means that a TASK_TRACED task
1. Will be awakened by signal_wake_up(1)
2. Can't sleep again via ptrace_notify()
3. Can't go to do_signal_stop() after return
from ptrace_stop() in get_signal_to_deliver()
So we can remove all ptrace related stuff from coredump path.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Incrementally update my proc-dont-lock-task_structs-indefinitely patches so
that they work with struct pid instead of struct task_ref.
Mostly this is a straight 1-1 substitution.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Every inode in /proc holds a reference to a struct task_struct. If a
directory or file is opened and remains open after the the task exits this
pinning continues. With 8K stacks on a 32bit machine the amount pinned per
file descriptor is about 10K.
Normally I would figure a reasonable per user process limit is about 100
processes. With 80 processes, with a 1000 file descriptors each I can trigger
the 00M killer on a 32bit kernel, because I have pinned about 800MB of useless
data.
This patch replaces the struct task_struct pointer with a pointer to a struct
task_ref which has a struct task_struct pointer. The so the pinning of dead
tasks does not happen.
The code now has to contend with the fact that the task may now exit at any
time. Which is a little but not muh more complicated.
With this change it takes about 1000 processes each opening up 1000 file
descriptors before I can trigger the OOM killer. Much better.
[mlp@google.com: task_mmu small fixes]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Paul Jackson <pj@sgi.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Albert Cahalan <acahalan@gmail.com>
Signed-off-by: Prasanna Meda <mlp@google.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To keep the dcache from filling up with dead /proc entries we flush them on
process exit. However over the years that code has gotten hairy with a
dentry_pointer and a lock in task_struct and misdocumented as a correctness
feature.
I have rewritten this code to look and see if we have a corresponding entry in
the dcache and if so flush it on process exit. This removes the extra fields
in the task_struct and allows me to trivially handle the case of a
/proc/<tgid>/task/<pid> entry as well as the current /proc/<pid> entries.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The sole renaming use of proc_inode.type is to discover the file descriptor
number, so just store the file descriptor number and don't wory about
processing this field. This removes any /proc limits on the maximum number of
file descriptors, and clears the path to make the hard coded /proc inode
numbers go away.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the IOCTLs of the Gigaset drivers to compat_ioctl.h in order to make
them available for 32 bit programs on 64 bit platforms. Please merge.
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes the clock source updates in update_wall_time() to correctly
track the time coming in via current_tick_length(). Optimize the fast
paths to be as short as possible to keep the overhead low.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Acked-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a CLOCKSOURCE_MASK macro to simplify initializing the mask for a struct
clocksource, and use it to replace literal mask constants in the various
clocksource drivers.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As suggested by Roman Zippel, change clocksource functions to use
clocksource_xyz rather then xyz_clocksource to avoid polluting the
namespace.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduces clocksource switching code and the arch generic time accessor
functions that use the clocksource infrastructure.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of incrementing xtime by tick_nsec + ntp adjustments, use the
clocksource abstraction to increment and scale time. Using the clocksource
abstraction allows other clocksources to be used consistently in the face of
late or lost ticks, while preserving the existing behavior via the jiffies
clocksource.
This removes the need to keep time_phase adjustments as we just use the
current_tick_length() function as the NTP interface and accumulate time using
shifted nanoseconds.
The basics of this design was by Roman Zippel, however it is my own
interpretation and implementation, so the credit should go to him and the
blame to me.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the current_tick_length() function so it takes an argument which
specifies how much precision to return in shifted nanoseconds. This provides
a simple way to convert between NTPs internal nanoseconds shifted by
(SHIFT_SCALE - 10) to other shifted nanosecond units that are used by the
clocksource abstraction.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modify the update_wall_time function so it increments time using the
clocksource abstraction instead of jiffies. Since the only clocksource driver
currently provided is the jiffies clocksource, this should result in no
functional change. Additionally, a timekeeping_init and timekeeping_resume
function has been added to initialize and maintain some of the new timekeping
state.
[hirofumi@mail.parknet.co.jp: fixlet]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This introduces the clocksource management infrastructure. A clocksource is a
driver-like architecture generic abstraction of a free-running counter. This
code defines the clocksource structure, and provides management code for
registering, selecting, accessing and scaling clocksources.
Additionally, this includes the trivial jiffies clocksource, a lowest common
denominator clocksource, provided mainly for use as an example.
[hirofumi@mail.parknet.co.jp: Don't enable IRQ too early]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the ability for key creation to overrun the user's quota in some
circumstances - notably when a session keyring is created and assigned to a
process that didn't previously have one.
This means it's still possible to log in, should PAM require the creation of a
new session keyring, and fix an overburdened key quota.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
V4L2_CID_MPEG_STREAM_VBI_FMT controls if and how VBI data is embedded in
an MPEG stream. Currently only one format is supported: the format designed
for the ivtv driver. This should be extended with new standard formats
(such as defined for DVB) in the future.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
HM12 is a YUV 4:1:1 format used by the cx2341x MPEG encoder/decoder for
the raw YUV input/output. The Y and UV planes are broken up in 16x16
macroblocks and each macroblock is transmitted in turn (row by row).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We do need to change these names now and even more so in future with
instantiated algorithms. So let's stop lying to the compiler and get
rid of the const modifiers.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds the hooks cra_init/cra_exit which are called during a tfm's
construction and destruction respectively. This will be used by the instances
to allocate child tfm's.
For now this lets us get rid of the coa_init/coa_exit functions which are
used for exactly that purpose (unlike the dia_init function which is called
for each transaction).
In fact the coa_exit path is currently buggy as it may get called twice
when an error is encountered during initialisation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Up until now algorithms have been happy to get a context pointer since
they know everything that's in the tfm already (e.g., alignment, block
size).
However, once we have parameterised algorithms, such information will
be specific to each tfm. So the algorithm API needs to be changed to
pass the tfm structure instead of the context pointer.
This patch is basically a text substitution. The only tricky bit is
the assembly routines that need to get the context pointer offset
through asm-offsets.h.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The netpoll system currently has a rx to tx path via:
netpoll_rx
__netpoll_rx
arp_reply
netpoll_send_skb
dev->hard_start_tx
This rx->tx loop places network drivers at risk of inadvertently causing a
deadlock or BUG halt by recursively trying to acquire a spinlock that is
used in both their rx and tx paths (this problem was origionally reported
to me in the 3c59x driver, which shares a spinlock between the
boomerang_interrupt and boomerang_start_xmit routines).
This patch breaks this loop, by queueing arp frames, so that they can be
responded to after all receive operations have been completed. Tested by
myself and the reported with successful results.
Specifically it was tested with netdump. Heres the BZ with details:
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=194055
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a mispelling of the korean alphabet name in the input subsystem.
See http://en.wikipedia.org/wiki/Hangeul#Names for more details.
KEY_HANGUEL left to not break people
Signed-off-by: Jerome Pinot <ngc891@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Name, phys and uniq are quite often constant strings in moules implementing
particular input device. If a module unregisters input device and then gets
unloaded, the device could still be present in memory (pinned via sysfs),
but aforementioned members would point to some random memory. Set them all
to NULL when unregistering so sysfs handlers won't try dereferencing them.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Treat HW coordination as independent CPUs.
This enables per-cpu monintoring of P-states
http://bugzilla.kernel.org/show_bug.cgi?id=5737
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commits
3e3318dee0 [PATCH] swsusp: x86_64 mark special saveable/unsaveable pages
b6370d96e0 [PATCH] swsusp: i386 mark special saveable/unsaveable pages
ce4ab0012b [PATCH] swsusp: add architecture special saveable pages support
because not only do they apparently cause page faults on x86, the
infrastructure doesn't compile on powerpc.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.linux-nfs.org/pub/linux/nfs-2.6: (51 commits)
nfs: remove nfs_put_link()
nfs-build-fix-99
git-nfs-build-fixes
Merge branch 'odirect'
NFS: alloc nfs_read/write_data as direct I/O is scheduled
NFS: Eliminate nfs_get_user_pages()
NFS: refactor nfs_direct_free_user_pages
NFS: remove user_addr, user_count, and pos from nfs_direct_req
NFS: "open code" the NFS direct write rescheduler
NFS: Separate functions for counting outstanding NFS direct I/Os
NLM: Fix reclaim races
NLM: sem to mutex conversion
locks.c: add the fl_owner to nlm_compare_locks
NFS: Display the chosen RPCSEC_GSS security flavour in /proc/mounts
NFS: Split fs/nfs/inode.c
NFS: Fix typo in nfs_do_clone_mount()
NFS: Fix compile errors introduced by referrals patches
NFSv4: Ensure that referral mounts bind to a reserved port
NFSv4: A root pathname is sent as a zero component4
NFSv4: Follow a referral
...
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (244 commits)
V4L/DVB (4210b): git-dvb: tea575x-tuner build fix
V4L/DVB (4210a): git-dvb versus matroxfb
V4L/DVB (4209): Added some BTTV PCI IDs for newer boards
Fixes some sync issues between V4L/DVB development and GIT
V4L/DVB (4206): Cx88-blackbird: always set encoder height based on tvnorm->id
V4L/DVB (4205): Merge tda9887 module into tuner.
V4L/DVB (4203): Explicitly set the enum values.
V4L/DVB (4202): allow selecting CX2341x port mode
V4L/DVB (4200): Disable bitrate_mode when encoding mpeg-1.
V4L/DVB (4199): Add cx2341x-specific control array to cx2341x.c
V4L/DVB (4198): Avoid newer usages of obsoleted experimental MPEGCOMP API
V4L/DVB (4197): Port new MPEG API to saa7134-empress with saa6752hs
V4L/DVB (4196): Port cx88-blackbird to the new MPEG API.
V4L/DVB (4193): Update cx2341x fw encoding API doc.
V4L/DVB (4192): Use control helpers for saa7115, cx25840, msp3400.
V4L/DVB (4191): Add CX2341X MPEG encoder module.
V4L/DVB (4190): Add helper functions for control processing to v4l2-common.
V4L/DVB (4189): Add videodev support for VIDIOC_S/G/TRY_EXT_CTRLS.
V4L/DVB (4188): Add new MPEG control/ioctl definitions to videodev2.h
V4L/DVB (4186): Add support for the DNTV Live! mini DVB-T card.
...
Stringify does what it was told to do.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In current 2.6.17 implementation, signal_struct refered from task_struct is
used for per-process data structure. The pacct facility also uses it as a
per-process data structure to store stime, utime, minflt, majflt. But those
members are saved in __exit_signal(). It's too late.
For example, if some threads exits at same time, pacct facility has a
possibility to drop accountings for a part of those threads. (see, the
following 'The results of original 2.6.17 kernel') I think accounting
information should be completely collected into the per-process data structure
before writing out an accounting record.
This patch fixes this matter. Accumulation of stime, utime, minflt and majflt
are done before generating accounting record.
[mingo@elte.hu: fix acct_collect() siglock bug found by lockdep]
Signed-off-by: KaiGai Kohei <kaigai@ak.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When pacct facility generate an 'ac_flag' field in accounting record, it
refers a task_struct of the thread which died last in the process. But any
other task_structs are ignored.
Therefore, pacct facility drops ASU flag even if root-privilege operations are
used by any other threads except the last one. In addition, AFORK flag is
always set when the thread of group-leader didn't die last, although this
process has called execve() after fork().
We have a same matter in ac_exitcode. The recorded ac_exitcode is an exit
code of the last thread in the process. There is a possibility this exitcode
is not the group leader's one.
The pacct facility need an i/o operation when an accounting record is
generated. There is a possibility to wake OOM killer up. If OOM killer is
activated, it kills some processes to make them release process memory
regions.
But acct_process() is called in the killed processes context before calling
exit_mm(), so those processes cannot release own memory. In the results, any
processes stop in this point and it finally cause a system stall.
Add support for SyncLink GT2 adapter to driver.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add custom HDLC idle pattern feature.
It allows the user to specify an arbitrary 8 or 16 bit repeating pattern on
the transmit data pin between HDLC frames.
In most cases the idle pattern is continuous ones or flags as supported by off
the shelf synchronous controllers and defined in the ISO3309 standard. Some
applications (radio/satellite modems, connections to legacy military hardware)
require non-standard patterns.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move kthread API kernel-doc from kthread.h to kthread.c & fix it.
Add kthread API to kernel-api DocBook.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement kasprintf, a kernel version of asprintf. This allocates the
memory required for the formatted string, including the trailing '\0'.
Returns NULL on allocation failure.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix kernel-doc formatting in ktime.h and hrtimer.[ch] files.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the linkat() syscall was added the flag parameter was added in the
last minute but it wasn't used so far. The following patch should change
that. My tests show that this is all that's needed.
If OLDNAME is a symlink setting the flag causes linkat to follow the
symlink and create a hardlink with the target. This is actually the
behavior POSIX demands for link() as well but Linux wisely does not do
this. With this flag (which will most likely be in the next POSIX
revision) the programmer can choose the behavior, defaulting to the safe
variant. As a side effect it is now possible to implement a
POSIX-compliant link(2) function for those who are interested.
touch file
ln -s file symlink
linkat(fd, "symlink", fd, "newlink", 0)
-> newlink is hardlink of symlink
linkat(fd, "symlink", fd, "newlink", AT_SYMLINK_FOLLOW)
-> newlink is hardlink of file
The value of AT_SYMLINK_FOLLOW is determined by the definition we already
use in glibc.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update loop.c to use a kthread instead of a deprecated kernel_thread for
loop devices.
[akpm@osdl.org: don't change the thread's name]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add synchronous request interruption. This is needed for file locking
operations which have to be interruptible. However filesystem may implement
interruptibility of other operations (e.g. like NFS 'intr' mount option).
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds POSIX file locking support to the fuse interface.
This implementation doesn't keep any locking state in kernel. Unlocking on
close() is handled by the FLUSH message, which now contains the lock owner id.
Mandatory locking is not supported. The filesystem may enfoce mandatory
locking in userspace if needed.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patches add POSIX file locking to the fuse interface.
Additional changes ralated to this are:
- asynchronous interrupt of requests by SIGKILL no longer supported
- separate control filesystem, instead of using sysfs objects
- add support for synchronously interrupting requests
Details are documented in Documentation/filesystems/fuse.txt throughout the
patches.
This patch:
Have fuse.h use MISC_MAJOR rather than a hardcoded '10'.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The table is empty, why does it still exist?
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
RTC: Add exported function rtc_year_days() to calculate the tm_yday value.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for the v3020 RTC from EM Microelectronic.
The v3020 RTC is designed to be connected on a bus using only one data bit.
Since any data bit may be used, it is necessary to specify this to the
driver by passing a struct v3020_platform_data pointer (see
include/linux/rtc-v3020.h) to the driver.
Part of the following code comes from the kernel patchs produced by
Compulab for their products. The original file (available here:
http://raph.people.8d.com/misc/emv3020.c) was released under the terms of
the GPL license.
[akpm@osdl.org: cleanups]
Signed-off-by: Raphael Assenat <raph@raphnet.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Import genrtc's RTC UIE emulation (CONFIG_GEN_RTC_X) to rtc-dev driver with
slight adjustments/refinements. This makes UIE-less rtc drivers work
better with programs doing read/poll on /dev/rtc, such as hwclock. This
emulation should not harm rtc drivers with UIE support, since
rtc_dev_ioctl() calls underlaying rtc driver's ioctl() first.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A few days ago Arjan signaled a lockdep red flag on epoll locks, and
precisely between the epoll's device structure lock (->lock) and the wait
queue head lock (->lock).
Like I explained in another email, and directly to Arjan, this can't happen
in reality because of the explicit check at eventpoll.c:592, that does not
allow to drop an epoll fd inside the same epoll fd. Since lockdep is
working on per-structure locks, it will never be able to know of policies
enforced in other parts of the code.
It was decided time ago of having the ability to drop epoll fds inside
other epoll fds, that triggers a very trick wakeup operations (due to
possibly reentrant callback-driven wakeups) handled by the
ep_poll_safewake() function. While looking again at the code though, I
noticed that all the operations done on the epoll's main structure wait
queue head (->wq) are already protected by the epoll lock (->lock), so that
locked-style functions can be used to manipulate the ->wq member. This
makes both a lock-acquire save, and lockdep happy.
Running totalmess on my dual opteron for a while did not reveal any problem
so far:
http://www.xmailserver.org/totalmess.c
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Christoph Lameter