The unix_dgram_sendmsg routine use the following test
if (unlikely(unix_peer(other) != sk && unix_recvq_full(other))) {
to determine if sk and other are in an n:1 association (either
established via connect or by using sendto to send messages to an
unrelated socket identified by address). This isn't correct as the
specified address could have been bound to the sending socket itself or
because this socket could have been connected to itself by the time of
the unix_peer_get but disconnected before the unix_state_lock(other). In
both cases, the if-block would be entered despite other == sk which
might either block the sender unintentionally or lead to trying to unlock
the same spin lock twice for a non-blocking send. Add a other != sk
check to guard against this.
Fixes: 7d267278a9 ("unix: avoid use-after-free in ep_remove_wait_queue")
Reported-By: Philipp Hahn <pmhahn@pmhahn.de>
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Tested-by: Philipp Hahn <pmhahn@pmhahn.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The present unix_stream_read_generic contains various code sequences of
the form
err = -EDISASTER;
if (<test>)
goto out;
This has the unfortunate side effect of possibly causing the error code
to bleed through to the final
out:
return copied ? : err;
and then to be wrongly returned if no data was copied because the caller
didn't supply a data buffer, as demonstrated by the program available at
http://pad.lv/1540731
Change it such that err is only set if an error condition was detected.
Fixes: 3822b5c2fc ("af_unix: Revert 'lock_interruptible' in stream receive code")
Reported-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My analysis in the below mail applies, although the second part is
unnecessary because i isn't used in arithmetic operations here:
https://marc.info/?l=openbsd-tech&m=145377854103866&w=2
Thanks for your time.
Signed-off-by: Michael McConville <mmcco@mykolab.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BRIDGE_VLAN_FILTERING automatically adds a newly bridged port to the
VLAN with the bridge's default_pvid.
The mv88e6xxx driver currently reserves VLANs 4000+ for unbridged ports
isolation. When a port joins a bridge, it leaves its reserved VLAN. When
a port leaves a bridge, it joins again its reserved VLAN.
But if the VLAN filtering is disabled, or if this hardware VLAN is
already in use, the bridged port ends up with no default VLAN, and the
communication with the CPU is thus broken.
To fix this, make a port join its reserved VLAN once on setup, never
leave it, and restore its PVID after another one was eventually used.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
smatch detected a suspicious looking bitop condition:
drivers/net/ethernet/cavium/liquidio/lio_main.c:2529
handle_timestamp() warn: suspicious bitop condition
(skb_shinfo(skb)->tx_flags | SKBTX_IN_PROGRESS is always non-zero,
so the logic is definitely not correct. Use & to mask the correct
bit.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c0eb454034 ("hv_netvsc: Don't ask for additional head room in the
skb") got rid of needed_headroom setting for the driver. With the change I
hit the following issue trying to use ptkgen module:
[ 57.522021] kernel BUG at net/core/skbuff.c:1128!
[ 57.522021] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
...
[ 58.721068] Call Trace:
[ 58.721068] [<ffffffffa0144e86>] netvsc_start_xmit+0x4c6/0x8e0 [hv_netvsc]
...
[ 58.721068] [<ffffffffa02f87fc>] ? pktgen_finalize_skb+0x25c/0x2a0 [pktgen]
[ 58.721068] [<ffffffff814f5760>] ? __netdev_alloc_skb+0xc0/0x100
[ 58.721068] [<ffffffffa02f9907>] pktgen_thread_worker+0x257/0x1920 [pktgen]
Basically, we're calling skb_cow_head(skb, RNDIS_AND_PPI_SIZE) and crash on
if (skb_shared(skb))
BUG();
We probably need to restore needed_headroom setting (but shrunk to
RNDIS_AND_PPI_SIZE as we don't need more) to request the required headroom
space. In theory, it should not give us performance penalty.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gregory CLEMENT says:
====================
mvneta fixes for SMP
Following this bug report:
http://thread.gmane.org/gmane.linux.ports.arm.kernel/468173 and the
suggestions from Russell King, I reviewed all the code involving
multi-CPU. It ended with this series of patches which should improve
the stability of the driver.
During my test I found another bug which is fixed by new patch (the
second one of this new version of the series)
The two first patches fix real bugs, the others fix potential issues
in the driver.
Changelog:
v1 -> v2
Fix spinlock comment. Pointed by David Miller
v2 -> v3
- Fix typos and mistake in the comments. Pointed by Sergei Shtylyov
- Add a new patch fixing the CPU choice in mvneta_percpu_elect
- Use lock in last patch to prevent remaining race condition. Pointed
by Jisheng
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When stopping the port, the CPU notifier are still there whereas the
mvneta_stop_dev function calls mvneta_percpu_disable() on each CPUs.
It was possible to have a new CPU coming at this point which could be
racy.
This patch adds a flag preventing executing the code notifier for a new
CPU when the port is stopping. It also uses the spinlock introduces
previously. To avoid the deadlock, the lock has been moved outside the
mvneta_percpu_elect function.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Electing a CPU must be done in an atomic way: it should be done after or
before the removal/insertion of a CPU and this function is not reentrant.
During the loop of mvneta_percpu_elect we associates the queues to the
CPUs, if there is a topology change during this loop, then the mapping
between the CPUs and the queues could be wrong. During this loop the
interrupt mask is also updating for each CPUs, It should not be changed
in the same time by other part of the driver.
This patch adds spinlock to create the needed critical sections.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the MVNETA_INTR_* registers, the queues related fields are per cpu,
according to the datasheet (comment in [] are added by me):
"In a multi-CPU system, bits of RX[or TX] queues for which the access by
the reading[or writing] CPU is disabled are read as 0, and cannot be
cleared[or written]."
That means that each time we want to manipulate these bits we had to do
it on each cpu and not only on the current cpu.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the commit 2dcf75e279 ("net: mvneta: Associate RX queues with
each CPU") all the percpu irq are used and disabled at initialization, so
there is no point to disable them first.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a for_each_* loop in which we just call the
smp_call_function_single macro, it is more simple to directly use the
on_each_cpu macro. Moreover, this macro ensures that the calls will be
done all at once.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When passing to the management of multiple RX queue, the
mvneta_percpu_elect function was broken. The use of the modulo can lead
to elect the wrong cpu. For example with rxq_def=2, if the CPU 2 goes
offline and then online, we ended with the third RX queue activated in
the same time on CPU 0 and CPU2, which lead to a kernel crash.
With this fix, we don't try to get "the closer" CPU if the default CPU is
gone, now we just use CPU 0 which always be there. Thanks to this, the
code becomes more readable, easier to maintain and more predicable.
Cc: stable@vger.kernel.org
Fixes: 2dcf75e279 ("net: mvneta: Associate RX queues with each CPU")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch convert the for_each_present in on_each_cpu, instead of
applying on the present cpus it will be applied only on the online cpus.
This fix a bug reported on
http://thread.gmane.org/gmane.linux.ports.arm.kernel/468173.
Using the macro on_each_cpu (instead of a for_each_* loop) also ensures
that all the calls will be done all at once.
Fixes: f864288544 ("net: mvneta: Statically assign queues to CPUs")
Reported-by: Stefan Roese <stefan.roese@gmail.com>
Suggested-by: Jisheng Zhang <jszhang@marvell.com>
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are typos in setting RTL8168H hardware parameters. If system install
another version driver that may cuase system hang.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry reported memory leaks of IP options allocated in
ip_cmsg_send() when/if this function returns an error.
Callers are responsible for the freeing.
Many thanks to Dmitry for the report and diagnostic.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value of kzalloc on failure of allocation of memory should
be -ENOMEM and not -1.
Found using Coccinelle. A simplified version of the semantic patch
used is:
//<smpl>
@@
expression *e;
position p,q;
@@
e@q = kzalloc(...);
if@p (e == NULL) {
...
return
- -1
+ -ENOMEM
;
}
//</smpl>
This function may also return -1 after calling mpp2_prs_tcam_port_map_get.
So that the function consistently returns meaningful error values on
failure, the -1 is changed to -EINVAL.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value of vmalloc on failure of allocation of memory should
be -ENOMEM and not -1.
Found using Coccinelle. A simplified version of the semantic patch
used is:
//<smpl>
@@
expression *e;
identifier l1;
position p,q;
@@
e@q = vmalloc(...);
if@p (e == NULL) {
...
goto l1;
}
l1:
...
return -1
+ -ENOMEM
;
//</smpl
The single call site of the containing function checks whether the
returned value is -1, so this check is changed as well. The single call
site of this call site, however, only checks whether the value is not 0,
so no further change was required.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current logic in bond_arp_rcv will accept an incoming ARP for
validation if (a) the receiving slave is either "active" (which includes
the currently active slave, or the current ARP slave) or, (b) there is a
currently active slave, and it has received an ARP since it became active.
For case (b), the receiving slave isn't the currently active slave, and is
receiving the original broadcast ARP request, not an ARP reply from the
target.
This logic can fail if there is no currently active slave. In
this situation, the ARP probe logic cycles through all slaves, assigning
each in turn as the "current_arp_slave" for one arp_interval, then setting
that one as "active," and sending an ARP probe from that slave. The
current logic expects the ARP reply to arrive on the sending
current_arp_slave, however, due to switch FDB updating delays, the reply
may be directed to another slave.
This can arise if the bonding slaves and switch are working, but
the ARP target is not responding. When the ARP target recovers, a
condition may result wherein the ARP target host replies faster than the
switch can update its forwarding table, causing each ARP reply to be sent
to the previous current_arp_slave. This will never pass the logic in
bond_arp_rcv, as neither of the above conditions (a) or (b) are met.
Some experimentation on a LAN shows ARP reply round trips in the
200 usec range, but my available switches never update their FDB in less
than 4000 usec.
This patch changes the logic in bond_arp_rcv to additionally
accept an ARP reply for validation on any slave if there is a current ARP
slave and it sent an ARP probe during the previous arp_interval.
Fixes: aeea64ac71 ("bonding: don't trust arp requests unless active slave really works")
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Probe errorpath fix for the Altera
- irqchip ofnode pointer added to the DaVinci driver
- controller instance number correction for DaVinci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GFrb
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
- Probe errorpath fix for the Altera
- irqchip ofnode pointer added to the DaVinci driver
- controller instance number correction for DaVinci
* tag 'gpio-v4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: davinci: Fix the number of controllers allocated
gpio: davinci: Add the missing of-node pointer
gpio: gpio-altera: Remove gpiochip on probe failure.
intel_scu_ipcutil:
- underflow in scu_reg_access()
intel-hid:
- fix incorrect entries in intel_hid_keymap
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWvB16AAoJEKbMaAwKp3647mYH/3ACKkSu/xt63RXwCRCbKML3
NNnBzYZw6welU4sVs0gVKHtZs89X/9mYr28t2C8O0GpVRx/Gwqkog9Mqesj8aj5B
pYa4gX1ZiEsAxpouQ3TBl78W0YjpyhpjKWqczVDa+q+k6GIB9kFTgg9z0ywRB+b4
422ajdKxFg7CNi2ucbvO3ihCgLMMPie2csGeUBevUncXlciaitjqLVhstnxgUyK0
KXB18rBZLwud5MCSLeveboHStQJMwK8im1m2f86xohVo8IAd691HLOJunPJpsI9E
6pV9Ar26kaSsmMqgKeTGTbqPmZFdjfZjOhajzcIGFXpuEDrtZ2fUvCcgl8irK7o=
=Zx2F
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.5-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Just two small fixes for the 4.5-rc cycle:
intel_scu_ipcutil:
- underflow in scu_reg_access()
intel-hid:
- fix incorrect entries in intel_hid_keymap"
* tag 'platform-drivers-x86-v4.5-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
intel_scu_ipcutil: underflow in scu_reg_access()
intel-hid: fix incorrect entries in intel_hid_keymap
Pull networking fixes from David Miller:
1) Fix BPF handling of branch offset adjustmnets on backjumps, from
Daniel Borkmann.
2) Make sure selinux knows about SOCK_DESTROY netlink messages, from
Lorenzo Colitti.
3) Fix openvswitch tunnel mtu regression, from David Wragg.
4) Fix ICMP handling of TCP sockets in syn_recv state, from Eric
Dumazet.
5) Fix SCTP user hmacid byte ordering bug, from Xin Long.
6) Fix recursive locking in ipv6 addrconf, from Subash Abhinov
Kasiviswanathan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
bpf: fix branch offset adjustment on backjumps after patching ctx expansion
vxlan, gre, geneve: Set a large MTU on ovs-created tunnel devices
geneve: Relax MTU constraints
vxlan: Relax MTU constraints
flow_dissector: Fix unaligned access in __skb_flow_dissector when used by eth_get_headlen
of: of_mdio: Add marvell, 88e1145 to whitelist of PHY compatibilities.
selinux: nlmsgtab: add SOCK_DESTROY to the netlink mapping tables
sctp: translate network order to host order when users get a hmacid
enic: increment devcmd2 result ring in case of timeout
tg3: Fix for tg3 transmit queue 0 timed out when too many gso_segs
net:Add sysctl_max_skb_frags
tcp: do not drop syn_recv on all icmp reports
ipv6: fix a lockdep splat
unix: correctly track in-flight fds in sending process user_struct
update be2net maintainers' email addresses
dwc_eth_qos: Reset hardware before PHY start
ipv6: addrconf: Fix recursive spin lock call
- One fix to ipoib
- One fix to core sysfs code
- Four patches that resolve an oops found in testing of ocrdma and a couple
other ocrdma issues
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Wpl3
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"A few more minor fixes for rc3:
- One fix to ipoib
- One fix to core sysfs code
- Four patches that resolve an oops found in testing of ocrdma and a
couple other ocrdma issues"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
RDMA/ocrdma: Fixing ocrdma debugfs directory remove
RDMA/ocrdma: Fix pkey_index returned by driver in rq work completion
RDMA/ocrdma: populate max_sge_rd in device attributes
RDMA/ocrdma: Initialize stats resources in the driver before ib device registration.
IB/sysfs: remove unused va_list args
IB/IPoIB: Do not set skb truesize since using one linearskb
When ctx access is used, the kernel often needs to expand/rewrite
instructions, so after that patching, branch offsets have to be
adjusted for both forward and backward jumps in the new eBPF program,
but for backward jumps it fails to account the delta. Meaning, for
example, if the expansion happens exactly on the insn that sits at
the jump target, it doesn't fix up the back jump offset.
Analysis on what the check in adjust_branches() is currently doing:
/* adjust offset of jmps if necessary */
if (i < pos && i + insn->off + 1 > pos)
insn->off += delta;
else if (i > pos && i + insn->off + 1 < pos)
insn->off -= delta;
First condition (forward jumps):
Before: After:
insns[0] insns[0]
insns[1] <--- i/insn insns[1] <--- i/insn
insns[2] <--- pos insns[P] <--- pos
insns[3] insns[P] `------| delta
insns[4] <--- target_X insns[P] `-----|
insns[5] insns[3]
insns[4] <--- target_X
insns[5]
First case is if we cross pos-boundary and the jump instruction was
before pos. This is handeled correctly. I.e. if i == pos, then this
would mean our jump that we currently check was the patchlet itself
that we just injected. Since such patchlets are self-contained and
have no awareness of any insns before or after the patched one, the
delta is correctly not adjusted. Also, for the second condition in
case of i + insn->off + 1 == pos, means we jump to that newly patched
instruction, so no offset adjustment are needed. That part is correct.
Second condition (backward jumps):
Before: After:
insns[0] insns[0]
insns[1] <--- target_X insns[1] <--- target_X
insns[2] <--- pos <-- target_Y insns[P] <--- pos <-- target_Y
insns[3] insns[P] `------| delta
insns[4] <--- i/insn insns[P] `-----|
insns[5] insns[3]
insns[4] <--- i/insn
insns[5]
Second interesting case is where we cross pos-boundary and the jump
instruction was after pos. Backward jump with i == pos would be
impossible and pose a bug somewhere in the patchlet, so the first
condition checking i > pos is okay only by itself. However, i +
insn->off + 1 < pos does not always work as intended to trigger the
adjustment. It works when jump targets would be far off where the
delta wouldn't matter. But, for example, where the fixed insn->off
before pointed to pos (target_Y), it now points to pos + delta, so
that additional room needs to be taken into account for the check.
This means that i) both tests here need to be adjusted into pos + delta,
and ii) for the second condition, the test needs to be <= as pos
itself can be a target in the backjump, too.
Fixes: 9bac3d6d54 ("bpf: allow extended BPF programs access skb fields")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull libata fixes from Tejun Heo:
- PORTS_IMPL workaround for very early ahci controllers is misbehaving
on new systems. Disabled on recent ahci versions.
- Old-style PIO state machine had a horrible locking problem. Don't
know how we've been getting away this far. Fixed.
- Other device specific updates.
* 'for-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: Intel DNV device IDs SATA
libata: fix sff host state machine locking while polling
libata-sff: use WARN instead of BUG on illegal host state machine state
libata: disable forced PORTS_IMPL for >= AHCI 1.3
libata: blacklist a Viking flash model for MWDMA corruption
drivers: ata: wake port before DMA stop for ALPM
Pull cgroup fixes from Tejun Heo:
- The destruction path of cgroup objects are asynchronous and
multi-staged and some of them ended up destroying parents before
children leading to failures in cpu and memory controllers. Ensure
that parents are always destroyed after children.
- cpuset mm node migration was performed synchronously while holding
threadgroup and cgroup mutexes and the recent threadgroup locking
update resulted in a possible deadlock. The migration is best effort
and shouldn't have been performed under those locks to begin with.
Made asynchronous.
- Minor documentation fix.
* 'for-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
Documentation: cgroup: Fix 'cgroup-legacy' -> 'cgroup-v1'
cgroup: make sure a parent css isn't freed before its children
cgroup: make sure a parent css isn't offlined before its children
cpuset: make mm migration asynchronous
Pull workqueue fixes from Tejun Heo:
"Workqueue fixes for v4.5-rc3.
- Remove a spurious triggering of flush dependency warning.
- Officially break local execution guarantee of unbound work items
and add a debug feature to flush out usages which depend on it.
- Work around CPU -> NODE mapping becoming invalid on CPU offline.
The branch is young but pushing out early as stable kernels are being
affected"
* 'for-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: handle NUMA_NO_NODE for unbound pool_workqueue lookup
workqueue: implement "workqueue.debug_force_rr_cpu" debug feature
workqueue: schedule WORK_CPU_UNBOUND work on wq_unbound_cpumask CPUs
Revert "workqueue: make sure delayed work run in local cpu"
workqueue: skip flush dependency checks for legacy workqueues
When looking up the pool_workqueue to use for an unbound workqueue,
workqueue assumes that the target CPU is always bound to a valid NUMA
node. However, currently, when a CPU goes offline, the mapping is
destroyed and cpu_to_node() returns NUMA_NO_NODE.
This has always been broken but hasn't triggered often enough before
874bbfe600 ("workqueue: make sure delayed work run in local cpu").
After the commit, workqueue forcifully assigns the local CPU for
delayed work items without explicit target CPU to fix a different
issue. This widens the window where CPU can go offline while a
delayed work item is pending causing delayed work items dispatched
with target CPU set to an already offlined CPU. The resulting
NUMA_NO_NODE mapping makes workqueue try to queue the work item on a
NULL pool_workqueue and thus crash.
While 874bbfe600 has been reverted for a different reason making the
bug less visible again, it can still happen. Fix it by mapping
NUMA_NO_NODE to the default pool_workqueue from unbound_pwq_by_node().
This is a temporary workaround. The long term solution is keeping CPU
-> NODE mapping stable across CPU off/online cycles which is being
worked on.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Len Brown <len.brown@intel.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/g/1454424264.11183.46.camel@gmail.com
Link: http://lkml.kernel.org/g/1453702100-2597-1-git-send-email-tangchen@cn.fujitsu.com
David Wragg says:
====================
Set a large MTU on ovs-created tunnel devices
Prior to 4.3, openvswitch tunnel vports (vxlan, gre and geneve) could
transmit vxlan packets of any size, constrained only by the ability to
send out the resulting packets. 4.3 introduced netdevs corresponding
to tunnel vports. These netdevs have an MTU, which limits the size of
a packet that can be successfully encapsulated. The default MTU
values are low (1500 or less), which is awkwardly small in the context
of physical networks supporting jumbo frames, and leads to a
conspicuous change in behaviour for userspace.
This patch series sets the MTU on openvswitch-created netdevs to be
the relevant maximum (i.e. the maximum IP packet size minus any
relevant overhead), effectively restoring the behaviour prior to 4.3.
Where relevant, the limits on MTU values that can be directly set on
the netdevs are also relaxed.
Changes in v2:
* Extend to all openvswitch tunnel types, i.e. gre and geneve as well
* Use IP_MAX_MTU
Changes in v3:
* Fix block comment style
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to 4.3, openvswitch tunnel vports (vxlan, gre and geneve) could
transmit vxlan packets of any size, constrained only by the ability to
send out the resulting packets. 4.3 introduced netdevs corresponding
to tunnel vports. These netdevs have an MTU, which limits the size of
a packet that can be successfully encapsulated. The default MTU
values are low (1500 or less), which is awkwardly small in the context
of physical networks supporting jumbo frames, and leads to a
conspicuous change in behaviour for userspace.
Instead, set the MTU on openvswitch-created netdevs to be the relevant
maximum (i.e. the maximum IP packet size minus any relevant overhead),
effectively restoring the behaviour prior to 4.3.
Signed-off-by: David Wragg <david@weave.works>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the MTU of geneve devices to be set to large values, in order to
exploit underlying networks with larger frame sizes.
GENEVE does not have a fixed encapsulation overhead (an openvswitch
rule can add variable length options), so there is no relevant maximum
MTU to enforce. A maximum of IP_MAX_MTU is used instead.
Encapsulated packets that are too big for the underlying network will
get dropped on the floor.
Signed-off-by: David Wragg <david@weave.works>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the MTU of vxlan devices without an underlying device to be set
to larger values (up to a maximum based on IP packet limits and vxlan
overhead).
Previously, their MTUs could not be set to higher than the
conventional ethernet value of 1500. This is a very arbitrary value
in the context of vxlan, and prevented vxlan devices from being able
to take advantage of jumbo frames etc.
The default MTU remains 1500, for compatibility.
Signed-off-by: David Wragg <david@weave.works>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver only needs to allocate for [ngpio / 32] controllers,
as each controller handles 32 gpios. But the current driver
allocates for ngpio of which the extra allocated are unused.
Fix it be registering only the required number of controllers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the first parameter of irq_domain_add_legacy is NULL.
irq_find_host function returns NULL when we do not populate the of_node
and hence irq_of_parse_and_map call fails whenever we want to request a
gpio irq. This fixes the request_irq failures for gpio interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
and a much more interesting kallsyms race which has been around approximately
forever. This fix is more invasive, and will require some care in backporting,
but I hated all the bandaids I could think of, so...
There are some more coming, which are only for breakages introduced this
cycle (livepatch), but wanted these in now.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Lt9v
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module fixes from Rusty Russell:
"Fix for async_probe module param added in 4.3 (clearly not widely used
yet), and a much more interesting kallsyms race which has been around
approximately forever. This fix is more invasive, and will require
some care in backporting, but I hated all the bandaids I could think
of, so...
There are some more coming, which are only for breakages introduced
this cycle (livepatch), but wanted these in now"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
modules: fix longstanding /proc/kallsyms vs module insertion race.
module: wrapper for symbol name.
modules: fix modparam async_probe request
drivers/input/touchscreen/colibri-vf50-ts.c: In function ‘vf50_ts_probe’:
drivers/input/touchscreen/colibri-vf50-ts.c:302: error: implicit declaration of function ‘of_property_read_u32’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The adp5589 has row 5, don't skip it when creating the GPIO mapping.
Otherwise the pin gets reserved as used and it is not possible to use it as
a GPIO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A recent patch broke parsing the gain, offset, and threshold parameters
from device tree. Instead of setting the cached values and writing them
to the correct registers during probe, it would write the values from DT
into the register address variables and never write them to the chip
during normal operation.
Fixes: 2e23b7a963 ("Input: edt-ft5x06 - use generic properties API")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Workqueue used to guarantee local execution for work items queued
without explicit target CPU. The guarantee is gone now which can
break some usages in subtle ways. To flush out those cases, this
patch implements a debug feature which forces round-robin CPU
selection for all such work items.
The debug feature defaults to off and can be enabled with a kernel
parameter. The default can be flipped with a debug config option.
If you hit this commit during bisection, please refer to 041bd12e27
("Revert "workqueue: make sure delayed work run in local cpu"") for
more information and ping me.
Signed-off-by: Tejun Heo <tj@kernel.org>
WORK_CPU_UNBOUND work items queued to a bound workqueue always run
locally. This is a good thing normally, but not when the user has
asked us to keep unbound work away from certain CPUs. Round robin
these to wq_unbound_cpumask CPUs instead, as perturbation avoidance
trumps performance.
tj: Cosmetic and comment changes. WARN_ON_ONCE() dropped from empty
(wq_unbound_cpumask AND cpu_online_mask). If we want that, it
should be done when config changes.
Signed-off-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This reverts commit 874bbfe600.
Workqueue used to implicity guarantee that work items queued without
explicit CPU specified are put on the local CPU. Recent changes in
timer broke the guarantee and led to vmstat breakage which was fixed
by 176bed1de5 ("vmstat: explicitly schedule per-cpu work on the CPU
we need it to run on").
vmstat is the most likely to expose the issue and it's quite possible
that there are other similar problems which are a lot more difficult
to trigger. As a preventive measure, 874bbfe600 ("workqueue: make
sure delayed work run in local cpu") was applied to restore the local
CPU guarnatee. Unfortunately, the change exposed a bug in timer code
which got fixed by 22b886dd10 ("timers: Use proper base migration in
add_timer_on()"). Due to code restructuring, the commit couldn't be
backported beyond certain point and stable kernels which only had
874bbfe600 started crashing.
The local CPU guarantee was accidental more than anything else and we
want to get rid of it anyway. As, with the vmstat case fixed,
874bbfe600 is causing more problems than it's fixing, it has been
decided to take the chance and officially break the guarantee by
reverting the commit. A debug feature will be added to force foreign
CPU assignment to expose cases relying on the guarantee and fixes for
the individual cases will be backported to stable as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 874bbfe600 ("workqueue: make sure delayed work run in local cpu")
Link: http://lkml.kernel.org/g/20160120211926.GJ10810@quack.suse.cz
Cc: stable@vger.kernel.org
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Daniel Bilik <daniel.bilik@neosystem.cz>
Cc: Jan Kara <jack@suse.cz>
Cc: Shaohua Li <shli@fb.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Bilik <daniel.bilik@neosystem.cz>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Michal Hocko <mhocko@kernel.org>
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
API:
- Fix async algif_skcipher, it was broken by recent fixes.
- Fix potential race condition in algif_skcipher with ctx.
- Fix potential memory corruption in algif_skcipher.
- Add missing lock to crypto_user when doing an alg dump.
Drivers:
- marvell/cesa was testing the wrong variable for NULL after
allocation.
- Fix potential double-free in atmel-sha.
- Fix illegal call to sleepin function from atomic context in
atmel-sha"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: marvell/cesa - fix test in mv_cesa_dev_dma_init()
crypto: atmel-sha - remove calls of clk_prepare() from atomic contexts
crypto: atmel-sha - fix atmel_sha_remove()
crypto: algif_skcipher - Do not set MAY_BACKLOG on the async path
crypto: algif_skcipher - Do not dereference ctx without socket lock
crypto: algif_skcipher - Do not assume that req is unchanged
crypto: user - lock crypto_alg_list on alg dump
Long ago, Dave Jones complained about CONFIG_LOCALVERSION_AUTO:
"I don't use the auto config, because I end up filling up /boot unless
I go through and clean them out by hand every time I install a new one
(which I do probably a dozen or so times a day). Is there some easy
way to prune old builds I'm missing?"
To which Bruce replied:
"I run this by hand every now and then. I'm probably doing it all wrong"
And if he is running it wrong, then so am I - because I've been using
this script ever since. It is true that CONFIG_LOCALVERSION_AUTO easily
ends up filling your /boot partition if you don't clean up old versions
regularly, and this script helps make that easier.
Checked with Bruce to see that it's fine to add this to the kernel
scripts. Maybe people will come up with enhancements, but more
importantly, this way I won't misplace this script whenever I install a
new machine and start doing custom kernels for it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes an issue with unaligned accesses when using
eth_get_headlen on a page that was DMA aligned instead of being IP aligned.
The fact is when trying to check the length we don't need to be looking at
the flow label so we can reorder the checks to first check if we are
supposed to gather the flow label and then make the call to actually get
it.
v2: Updated path so that either STOP_AT_FLOW_LABEL or KEY_FLOW_LABEL can
cause us to check for the flow label.
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ae46113196 ("of: of_mdio: Add a whitelist of PHY
compatibilities.") missed one compatible string used in in-tree DTBs:
in OCTEON, for selected boards, the kernel DTB pruning code will overwrite
the DTB compatible string with "marvell,88e1145", which is missing
from the whitelist. Add it.
The patch fixes broken networking on EdgeRouter Lite.
Fixes: ae46113196 ("of: of_mdio: Add a whitelist of PHY compatibilities.")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this, using SOCK_DESTROY in enforcing mode results in:
SELinux: unrecognized netlink message type=21 for sclass=32
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rainer Weikusat