Hardware allow to read the position in scanout buffer so
we can use this information to make wait of vblank more accurate.
Active area bounds (start, end, total height) have already been
computed and written in ltdc registers, read them and get the
current line position to compute vpos value.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: Yannick Fertré <yannick.fertre@st.com>
Tested-by: Yannick Fertré <yannick.fertre@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180629130140.16004-1-benjamin.gaignard@linaro.org
Filter the requested mode pixel clock frequency according
to the pad maximum supported frequency.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1530271342-5532-1-git-send-email-yannick.fertre@st.com
Hw older versions support non-alpha color formats derived
from native alpha color formats only on the primary layer.
For instance, RG16 native format without alpha works fine
on 2nd layer but XR24 (derived color format from AR24)
does not work on 2nd layer.
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180201104243.20726-3-philippe.cornu@st.com
Use drm_fb_cma_fbdev_init() and drm_fb_cma_fbdev_fini() which relies on
the fact that drm_device holds a pointer to the drm_fb_helper structure.
This means that the driver doesn't have to keep track of that.
Also use the drm_fb_helper functions directly.
Remove duplicate ldev assignment.
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Philippe Cornu <philippe.cornu@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115142001.45358-14-noralf@tronnes.org
The redundant fb helper .load_lut is no longer used, and can not
work right without also providing the fb helpers .gamma_set and
.gamma_get thus rendering the code in this driver suspect.
Just remove the dead code.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170713162538.22788-14-peda@axentia.se
This controller provides output signals to interface directly a variety
of LCD and TFT panels. These output signals are: RGB signals
(up to 24bpp), vertical & horizontal synchronisations, data enable and
the pixel clock.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/1492164819-10513-5-git-send-email-yannick.fertre@st.com
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Yannick Fertré