Current code calls omap4430_phy_init() twice in usb_musb_init().
Calling omap4430_phy_init() once is enough.
This patch removes the first omap4430_phy_init() call, which using an
uninitialized pointer as parameter.
This patch elimates below build warning:
arch/arm/mach-omap2/usb-musb.c: In function 'usb_musb_init':
arch/arm/mach-omap2/usb-musb.c:141: warning: 'dev' may be used uninitialized in this function
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Bjarne Steinsbo <bsteinsbo@gmail.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like 2600 kHz rate does not work reliably on 2430,
so just use the 100 kHz rate.
Otherwise the system often fails to boot properly with:
omap_i2c omap_i2c.2: timeout waiting for bus ready
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
twl: clock init err [-110]
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
TWL4030 Unable to unlock IDCODE registers --110
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove OMAP4_USBC1_ICUSB_PWRDNZ_MASK during enable/disable PWRDNZ mode for
MMC1_PBIAS and associated extended-drain MMC1 I/O cell. This is in accordance
with the control module programming guide. This fixes a bug where if trying to
use gpio_98 or gpio_99 and MMC1 at the same time the GPIO signal will be
affected by a changing SDMMC1_VDDS.
Software must keep MMC1_PBIAS cell and MMC1_IO cell PWRDNZ signals low whenever
SDMMC1_VDDS ramps up/down or changes for cell protection purposes.
MMC1 is based on SDMMC1_VDDS whereas USBC1 is based on SIM_VDDS therefore
they can operate independently.
Signed-off-by: Bryan Buckley <bryan.buckley@ti.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
David reported:
Attached below is a watered-down version of rt/tst-cpuclock2.c from
GLIBC. Just build it with "gcc -o test test.c -lpthread -lrt" or
similar.
Run it several times, and you will see cases where the main thread
will measure a process clock difference before and after the nanosleep
which is smaller than the cpu-burner thread's individual thread clock
difference. This doesn't make any sense since the cpu-burner thread
is part of the top-level process's thread group.
I've reproduced this on both x86-64 and sparc64 (using both 32-bit and
64-bit binaries).
For example:
[davem@boricha build-x86_64-linux]$ ./test
process: before(0.001221967) after(0.498624371) diff(497402404)
thread: before(0.000081692) after(0.498316431) diff(498234739)
self: before(0.001223521) after(0.001240219) diff(16698)
[davem@boricha build-x86_64-linux]$
The diff of 'process' should always be >= the diff of 'thread'.
I make sure to wrap the 'thread' clock measurements the most tightly
around the nanosleep() call, and that the 'process' clock measurements
are the outer-most ones.
---
#include <unistd.h>
#include <stdio.h>
#include <stdlib.h>
#include <time.h>
#include <fcntl.h>
#include <string.h>
#include <errno.h>
#include <pthread.h>
static pthread_barrier_t barrier;
static void *chew_cpu(void *arg)
{
pthread_barrier_wait(&barrier);
while (1)
__asm__ __volatile__("" : : : "memory");
return NULL;
}
int main(void)
{
clockid_t process_clock, my_thread_clock, th_clock;
struct timespec process_before, process_after;
struct timespec me_before, me_after;
struct timespec th_before, th_after;
struct timespec sleeptime;
unsigned long diff;
pthread_t th;
int err;
err = clock_getcpuclockid(0, &process_clock);
if (err)
return 1;
err = pthread_getcpuclockid(pthread_self(), &my_thread_clock);
if (err)
return 1;
pthread_barrier_init(&barrier, NULL, 2);
err = pthread_create(&th, NULL, chew_cpu, NULL);
if (err)
return 1;
err = pthread_getcpuclockid(th, &th_clock);
if (err)
return 1;
pthread_barrier_wait(&barrier);
err = clock_gettime(process_clock, &process_before);
if (err)
return 1;
err = clock_gettime(my_thread_clock, &me_before);
if (err)
return 1;
err = clock_gettime(th_clock, &th_before);
if (err)
return 1;
sleeptime.tv_sec = 0;
sleeptime.tv_nsec = 500000000;
nanosleep(&sleeptime, NULL);
err = clock_gettime(th_clock, &th_after);
if (err)
return 1;
err = clock_gettime(my_thread_clock, &me_after);
if (err)
return 1;
err = clock_gettime(process_clock, &process_after);
if (err)
return 1;
diff = process_after.tv_nsec - process_before.tv_nsec;
printf("process: before(%lu.%.9lu) after(%lu.%.9lu) diff(%lu)\n",
process_before.tv_sec, process_before.tv_nsec,
process_after.tv_sec, process_after.tv_nsec, diff);
diff = th_after.tv_nsec - th_before.tv_nsec;
printf("thread: before(%lu.%.9lu) after(%lu.%.9lu) diff(%lu)\n",
th_before.tv_sec, th_before.tv_nsec,
th_after.tv_sec, th_after.tv_nsec, diff);
diff = me_after.tv_nsec - me_before.tv_nsec;
printf("self: before(%lu.%.9lu) after(%lu.%.9lu) diff(%lu)\n",
me_before.tv_sec, me_before.tv_nsec,
me_after.tv_sec, me_after.tv_nsec, diff);
return 0;
}
This is due to us using p->se.sum_exec_runtime in
thread_group_cputime() where we iterate the thread group and sum all
data. This does not take time since the last schedule operation (tick
or otherwise) into account. We can cure this by using
task_sched_runtime() at the cost of having to take locks.
This also means we can (and must) do away with
thread_group_sched_runtime() since the modified thread_group_cputime()
is now more accurate and would deadlock when called from
thread_group_sched_runtime().
Aside of that it makes the function safe on 32 bit systems. The old
code added t->se.sum_exec_runtime unprotected. sum_exec_runtime is a
64bit value and could be changed on another cpu at the same time.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: stable@kernel.org
Link: http://lkml.kernel.org/r/1314874459.7945.22.camel@twins
Tested-by: David Miller <davem@davemloft.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The commit a810364a04
ALSA: hda - Handle -1 as invalid position, too
caused a regression on some machines that require the position-buffer
instead of LPIB, e.g. resulting in noises with mic recording with
PulseAudio.
This patch fixes the detection by delaying the test at the timing as
same as 3.0, i.e. doing the position check only when requested in
azx_position_ok().
Reported-and-tested-by: Rocko Requin <rockorequin@hotmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
__find_resource() incorrectly returns a resource window which overlaps
an existing allocated window. This happens when the parent's
resource-window spans 0x00000000 to 0xffffffff and is entirely allocated
to all its children resource-windows.
__find_resource() looks for gaps in resource allocation among the
children resource windows. When it encounters the last child window it
blindly tries the range next to one allocated to the last child. Since
the last child's window ends at 0xffffffff the calculation overflows,
leading the algorithm to believe that any window in the range 0x0000000
to 0xfffffff is available for allocation. This leads to a conflicting
window allocation.
Michal Ludvig reported this issue seen on his platform. The following
patch fixes the problem and has been verified by Michal. I believe this
bug has been there for ages. It got exposed by git commit 2bbc694227
("PCI : ability to relocate assigned pci-resources")
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Tested-by: Michal Ludvig <mludvig@logix.net.nz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'v4l_for_linus' of git://linuxtv.org/mchehab/for_linus:
[media] omap3isp: Fix build error in ispccdc.c
[media] uvcvideo: Fix crash when linking entities
[media] v4l: Make sure we hold a reference to the v4l2_device before using it
[media] v4l: Fix use-after-free case in v4l2_device_release
[media] uvcvideo: Set alternate setting 0 on resume if the bus has been reset
[media] OMAP_VOUT: Fix build break caused by update_mode removal in DSS2
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] cio: fix cio_tpi ignoring adapter interrupts
[S390] gmap: always up mmap_sem properly
[S390] Do not clobber personality flags on exec
* git://github.com/davem330/sparc:
sparc64: Force the execute bit in OpenFirmware's translation entries.
sparc: Make '-p' boot option meaningful again.
sparc, exec: remove redundant addr_limit assignment
sparc64: Future proof Niagara cpu detection.
* 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux:
drm/i915: FBC off for ironlake and older, otherwise on by default
drm/i915: Enable SDVO hotplug interrupts for HDMI and DVI
drm/i915: Enable dither whenever display bpc < frame buffer bpc
Apple Quad G5 has some oddity in it's device-tree which causes the new
generic matching code to fail to relate nodes for PCI-E devices below U4
with their respective struct pci_dev. This breaks graphics on those
machines among others.
This fixes it using a quirk which copies the node pointer from the host
bridge for the root complex, which makes the generic code work for the
children afterward.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit d5767c5353 ("bootup: move 'usermodehelper_enable()' to the end
of do_basic_setup()") moved 'usermodehelper_enable()' to end of
do_basic_setup() to after the initcalls. But then I get failed to let
uvesafb work on my computer, and lose the splash boot.
So maybe we could start usermodehelper_enable a little early to make
some task work that need eary init with the help of user mode.
[ I would *really* prefer that initcalls not call into user space - even
the real 'init' hasn't been execve'd yet, after all! But for uvesafb
it really does look like we don't have much choice.
I considered doing this when we mount the root filesystem, but
depending on config options that is in multiple places. We could do
the usermode helper enable as a rootfs_initcall()..
So I'm just using wang yanqing's trivial patch. It's not wonderful,
but it's simple and should work. We should revisit this some day,
though. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The commit aabdcb0b55 ("can bcm: fix tx_setup
off-by-one errors") fixed only a part of the original problem reported by
Andre Naujoks. It turned out that the original code needed to be re-ordered
to reduce complexity and to finally fix the reported frame counting issues.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrong pointer is being passed for raw data sanity checking, when parsing
sample event.
This ends up with invalid event and perf record being stuck in
__perf_session__process_events function during processing build IDs
(process_buildids function).
Following command hangs up in my setup:
./perf record -e raw_syscalls:sys_enter ls
The fix is to use proper pointer to the raw data instead of the 'u'
union.
Reviewed-by: David Ahern <dsahern@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1317308709-9474-2-git-send-email-jolsa@redhat.com
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In the OF 'translations' property, the template TTEs in the mappings
never specify the executable bit. This is the case even though some
of these mappings are for OF's code segment.
Therefore, we need to force the execute bit on in every mapping.
This problem can only really trigger on Niagara/sun4v machines and the
history behind this is a little complicated.
Previous to sun4v, the sun4u TTE entries lacked a hardware execute
permission bit. So OF didn't have to ever worry about setting
anything to handle executable pages. Any valid TTE loaded into the
I-TLB would be respected by the chip.
But sun4v Niagara chips have a real hardware enforced executable bit
in their TTEs. So it has to be set or else the I-TLB throws an
instruction access exception with type code 6 (protection violation).
We've been extremely fortunate to not get bitten by this in the past.
The best I can tell is that the OF's mappings for it's executable code
were mapped using permanent locked mappings on sun4v in the past.
Therefore, the fact that we didn't have the exec bit set in the OF
translations we would use did not matter in practice.
Thanks to Greg Onufer for helping me track this down.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the rds_iw_mr_pool struct the free_pinned field keeps track of
memory pinned by free MRs. While this field is incremented properly
upon allocation, it is never decremented upon unmapping. This would
cause the rds_rdma module to crash the kernel upon unloading, by
triggering the BUG_ON in the rds_iw_destroy_mr_pool function.
This change keeps track of the MRs that become unpinned, so that
free_pinned can be decremented appropriately.
Signed-off-by: Jonathan Lallinger <jonathan@ogc.us>
Signed-off-by: Steve Wise <swise@ogc.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
If request_irq fails, the ibmveth driver will overwrite
the rc and end up returning a successful rc on its open
function, resulting in an oops later when a packet gets
sent and buffers are not allocated due to the failed open.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_ac_list and ipv6_fl_list from listening socket are inadvertently
shared with new socket created for connection.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix EEH recovery on new P Series platform by
requesting fundamental reset.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes two off-by-one errors that canceled each other out.
Checking for the same condition two times in bcm_tx_timeout_tsklet() reduced
the count of frames to be sent by one. This did not show up the first time
tx_setup is invoked as an additional frame is sent due to TX_ANNONCE.
Invoking a second tx_setup on the same item led to a reduced (by 1) number of
sent frames.
Reported-by: Andre Naujoks <nautsch@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I got:
Generating server: Tehuti.onmicrosoft.com
baum@tehutinetworks.net
#< #5.1.1 smtp;550 5.1.1 RESOLVER.ADR.RecipNotFound; not found> #SMTP#
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Alexander Indenbaum <baum@tehutinetworks.net>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver has two warning messages that might be triggered
by normal use cases. When they appear, the messages give the
impression of a never ending series of errors.
This commit changes them to debug messages instead.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IEEE 1588 standard defines two kinds of messages, event and general
messages. Event messages require time stamping, and general do not. When
using UDP transport, two separate ports are used for the two message
types.
The BPF designed to recognize event messages incorrectly classifies L2
general messages as event messages. This commit fixes the issue by
extending the filter to check the message type field for L2 PTP packets.
Event messages are be distinguished from general messages by testing
the "general" bit.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Cc: <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing it just before starting to call into cpu_idle() made a sick kind
of sense only because the original bug we fixed (see commit
288d5abec831: "Boot up with usermodehelper disabled") was about problems
with some scheduler data structures not being initialized, and they had
better be initialized at that point.
But it really didn't make any other conceptual sense, and doing it after
the initial "schedule()" call for the idle thread actually opened up a
race: what if the main initialization thread did everything without
needing to sleep, and got all the way into user land too? Without
actually having scheduled back to the idle thread?
Now, in normal circumstances that doesn't ever happen, but it looks like
Richard Cochran triggered exactly that on his ARM IXP4xx machines:
"I have some ARM IXP4xx based machines that use the two on chip MAC
ports (aka NPEs). The NPE needs a firmware in order to function.
Ever since the following commit [that 288d5abec8 one], it is no
longer possible to bring up the interfaces during the init scripts."
with a call trace showing an ioctl coming from user space. Richard says:
"The init is busybox, and the startup script does mount, syslogd, and
then ifup, so that all can go by quickly."
The fix is to move the usermodehelper_enable() into the main 'init'
thread, and just put it after we've done all our initcalls. By then,
everything really should be up, but we've obviously not actually started
the user-mode portion of init yet.
Reported-and-tested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The incremental map updates have a record for each pg_temp mapping that is
to be add/updated (len > 0) or removed (len == 0). The old code was
written as if the updates were a complete enumeration; that was just wrong.
Update the code to remove 0-length entries and drop the rbtree traversal.
This avoids misdirected (and hung) requests that manifest as server
errors like
[WRN] client4104 10.0.1.219:0/275025290 misdirected client4104.1:129 0.1 to osd0 not [1,0] in e11/11
Signed-off-by: Sage Weil <sage@newdream.net>
We need to apply the modulo pg_num calculation before looking up a pgid in
the pg_temp mapping rbtree. This fixes pg_temp mappings, and fixes
(some) misdirected requests that result in messages like
[WRN] client4104 10.0.1.219:0/275025290 misdirected client4104.1:129 0.1 to osd0 not [1,0] in e11/11
on the server and stall make the client block without getting a reply (at
least until the pg_temp mapping goes way, but that can take a long long
time).
Reorder calc_pg_raw() a bit to make more sense.
Signed-off-by: Sage Weil <sage@newdream.net>
* git://github.com/davem330/net:
ipv6-multicast: Fix memory leak in IPv6 multicast.
ipv6: check return value for dst_alloc
net: check return value for dst_alloc
ipv6-multicast: Fix memory leak in input path.
bnx2x: add missing break in bnx2x_dcbnl_get_cap
bnx2x: fix WOL by enablement PME in config space
bnx2x: fix hw attention handling
net: fix a typo in Documentation/networking/scaling.txt
ath9k: Fix a dma warning/memory leak
rtlwifi: rtl8192cu: Fix unitialized struct
iwlagn: fix dangling scan request
batman-adv: do_bcast has to be true for broadcast packets only
cfg80211: Fix validation of AKM suites
iwlegacy: do not use interruptible waits
iwlegacy: fix command queue timeout
ath9k_hw: Fix Rx DMA stuck for AR9003 chips
* git://bedivere.hansenpartnership.com/git/scsi-rc-fixes-2.6:
[SCSI] 3w-9xxx: fix iommu_iova leak
[SCSI] cxgb3i: convert cdev->l2opt to use rcu to prevent NULL dereference
[SCSI] scsi: qla4xxx needs libiscsi.o
[SCSI] libsas: fix failure to revalidate domain for anything but the first expander child.
[SCSI] aacraid: reset should disable MSI interrupt
Storing the struct temp_data pointer allocated from create_core_data()
when returning an error has the potential of leaving around a pointer
to freed memory. Reset it to NULL for error returns.
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
With recent change "hwmon: (coretemp) don't use kernel assigned CPU
number as platform device ID", the microcode check is now running on
random CPU. Fix that by checking the microcode before creating the
platform device rather than at probe time.
Also avoid calling TO_PHYS_ID(cpu) twice in the same function, it's
expensive.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jan Beulich <jbeulich@suse.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
A kernel crash is observed when a mounted ext3/ext4 filesystem is
physically removed. The problem is that blk_cleanup_queue() frees up
some resources eg by calling elevator_exit(), which are not checked for
in normal operation. So we should rather move these calls to the
destructor function blk_release_queue() as at that point all remaining
references are gone. However, in doing so we have to ensure that any
externally supplied queue_lock is disconnected as the driver might free
up the lock after the call of blk_cleanup_queue(),
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* 'for-linus' of git://github.com/tiwai/sound:
ASoC: ssm2602: Re-enable oscillator after suspend
ALSA: usb-audio: Check for possible chip NULL pointer before clearing probing flag
ALSA: hda/realtek - Don't detect LO jack when identical with HP
ALSA: hda/realtek - Avoid bogus HP-pin assignment
ALSA: HDA: No power nids on 92HD93
ASoC: omap-mcbsp: Do not attempt to change DAI sysclk if stream is active
If reg_vif_xmit cannot find a routing entry, be sure to
free the skb before returning the error.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
return value of dst_alloc must be checked before use
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
return value of dst_alloc must be checked before use
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have to free the skb before returning if we fail
the fib lookup.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use register name to initialize attention mask
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Axel Lin