This patch fixes below warning during building htmldoc:
slimbus.h:352: warning: Function parameter or member 'name'
not described in 'slim_stream_runtime'
This patch also removes documentation for state variable
in struct slim_stream_runtime which was redundant and removed.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support to SLIMbus stream apis for slimbus device.
SLIMbus streaming involves adding support to Data Channel Management and
channel Reconfiguration Messages to slim core plus few stream apis.
>From slim device side the apis are very simple mostly inline with other
stream apis.
Currently it only supports Isochronous and Push/Pull transport protocols,
which are sufficient for audio use cases.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds suppor to Qualcomm SLIMBus Non-Generic Device (NGD)
controller driver.
This is light-weight SLIMBus controller driver responsible for
communicating with slave HW directly over the bus using messaging
interface, and communicating with master component residing on ADSP
for bandwidth and data-channel management
Based on intial work from
Karthikeyan Ramasubramanian <kramasub@codeaurora.org> and
Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds slim_alloc_txn_tid() and slim_free_txn_tid() api
to allow controllers like ngd to allocate tids for user specific
commands. This also cleans up the existing code to use single place
for tid allocations and free.
This patch also make the tid allocation cyclic one, its very useful
to track the transactions back during debug.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds some common constant defines which are required
for qcom slim controller driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per SLIMbus specification, a reconfiguration sequence known as
'clock pause' needs to be broadcast over the bus while entering low-
power mode. Clock-pause is initiated by the controller driver.
To exit clock-pause, controller typically wakes up the framer device.
Since wakeup precedure is controller-specific, framework calls it via
controller's function pointer to invoke it.
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SLIMbus devices use value-element, and information elements to
control device parameters (e.g. value element is used to represent
gain for codec, information element is used to represent interrupt
status for codec when codec interrupt fires).
Messaging APIs are used to set/get these value and information
elements. SLIMbus specification uses 8-bit "transaction IDs" for
messages where a read-value is anticipated. Framework uses a table
of pointers to store those TIDs and responds back to the caller in
O(1).
Caller can do synchronous and asynchronous reads/writes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support to slim controllers in the slim core,
including some utility functions invoked by the controller and
slim device drivers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Srinivas Kandagatla