As Erspan_v4, Erspan_v6 protocol relies on o_key to configure
session id header field. However TUNNEL_KEY bit is cleared in
ip6erspan_tunnel_xmit since ERSPAN protocol does not set the key field
of the external GRE header and so the configured o_key is not reported
to userspace. The issue can be triggered with the following reproducer:
$ip link add ip6erspan1 type ip6erspan local 2000::1 remote 2000::2 \
key 1 seq erspan_ver 1
$ip link set ip6erspan1 up
ip -d link sh ip6erspan1
ip6erspan1@NONE: <BROADCAST,MULTICAST> mtu 1422 qdisc noop state DOWN mode DEFAULT
link/ether ba:ff:09:24:c3:0e brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 1500
ip6erspan remote 2000::2 local 2000::1 encaplimit 4 flowlabel 0x00000 ikey 0.0.0.1 iseq oseq
Fix the issue adding TUNNEL_KEY bit to the o_flags parameter in
ip6gre_fill_info
Fixes: 5a963eb61b ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ERSPAN key header field as tunnel key in gre_parse_header routine
since ERSPAN protocol sets the key field of the external GRE header to
0 resulting in a tunnel lookup fail in ip6gre_err.
In addition remove key field parsing and pskb_may_pull check in
erspan_rcv and ip6erspan_rcv
Fixes: 5a963eb61b ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As said in draft-foschiano-erspan-03#section4:
Different frame variants known as "ERSPAN Types" can be
distinguished based on the GRE "Protocol Type" field value: Type I
and II's value is 0x88BE while Type III's is 0x22EB [ETYPES].
So set it properly in erspan_xmit() according to erspan_ver. While at
it, also remove the unused parameter 'proto' in erspan_fb_xmit().
Fixes: 94d7d8f292 ("ip6_gre: add erspan v2 support")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We forgot to update ip6erspan version related info when changing link,
which will cause setting new hwid failed.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: 94d7d8f292 ("ip6_gre: add erspan v2 support")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In changelink ops, the ip6gre_net pointer is retrieved from
dev_net(dev), which is wrong in case of x-netns. Thus, the tunnel is not
unlinked from its current list and is relinked into another net
namespace. This corrupts the tunnel lists and can later trigger a kernel
oops.
Fix this by retrieving the netns from device private area.
Fixes: c8632fc30b ("net: ip6_gre: Split up ip6gre_changelink()")
Cc: Petr Machata <petrm@mellanox.com>
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KMSAN detected read beyond end of buffer in vti and sit devices when
passing truncated packets with PF_PACKET. The issue affects additional
ip tunnel devices.
Extend commit 76c0ddd8c3 ("ip6_tunnel: be careful when accessing the
inner header") and commit ccfec9e5cb ("ip_tunnel: be careful when
accessing the inner header").
Move the check to a separate helper and call at the start of each
ndo_start_xmit function in net/ipv4 and net/ipv6.
Minor changes:
- convert dev_kfree_skb to kfree_skb on error path,
as dev_kfree_skb calls consume_skb which is not for error paths.
- use pskb_network_may_pull even though that is pedantic here,
as the same as pskb_may_pull for devices without llheaders.
- do not cache ipv6 hdrs if used only once
(unsafe across pskb_may_pull, was more relevant to earlier patch)
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed the is_gretap_dev and is_ip6gretap_dev logic from structure
comparison to string comparison of the rtnl_link_ops kind field.
This approach aligns with the current identification methods and function
names of vxlan and geneve network devices.
Convert mlxsw to use these helpers and use them in downstream mlx5 patch.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We'll need this to handle ICMP errors for tunnels without a sending socket
(i.e. FoU and GUE). There, we might have to look up different types of IP
tunnels, registered as network protocols, before we get a match, so we
want this for the error handlers of IPPROTO_IPIP and IPPROTO_IPV6 in both
inet_protos and inet6_protos. These error codes will be used in the next
patch.
For consistency, return sensible error codes in protocol error handlers
whenever handlers can't handle errors because, even if valid, they don't
match a protocol or any of its states.
This has no effect on existing error handling paths.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same as ip_gre, use gre_parse_header to parse gre header in gre error
handler code.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After erspan_ver is introudced, if erspan_ver is not set in iproute, its
value will be left 0 by default. Since Commit 02f99df187 ("erspan: fix
invalid erspan version."), it has broken the traffic due to the version
check in erspan_xmit if users are not aware of 'erspan_ver' param, like
using an old version of iproute.
To fix this compatibility problem, it sets erspan_ver to 1 by default
when adding an erspan dev in erspan_setup. Note that we can't do it in
ipgre_netlink_parms, as this function is also used by ipgre_changelink.
Fixes: 02f99df187 ("erspan: fix invalid erspan version.")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 GRO over GRE tap is not working while GRO is not set
over the native interface.
gro_list_prepare function updates the same_flow variable
of existing sessions to 1 if their mac headers match the one
of the incoming packet.
same_flow is used to filter out non-matching sessions and keep
potential ones for aggregation.
The number of bytes to compare should be the number of bytes
in the mac headers. In gro_list_prepare this number is set to
be skb->dev->hard_header_len. For GRE interfaces this hard_header_len
should be as it is set in the initialization process (when GRE is
created), it should not be overridden. But currently it is being overridden
by the value that is actually supposed to represent the needed_headroom.
Therefore, the number of bytes compared in order to decide whether the
the mac headers are the same is greater than the length of the headers.
As it's documented in netdevice.h, hard_header_len is the maximum
hardware header length, and needed_headroom is the extra headroom
the hardware may need.
hard_header_len is basically all the bytes received by the physical
till layer 3 header of the packet received by the interface.
For example, if the interface is a GRE tap then the needed_headroom
should be the total length of the following headers:
IP header of the physical, GRE header, mac header of GRE.
It is often used to calculate the MTU of the created interface.
This patch removes the override of the hard_header_len, and
assigns the calculated value to needed_headroom.
This way, the comparison in gro_list_prepare is really of
the mac headers, and if the packets have the same mac headers
the same_flow will be set to 1.
Performance testing: 45% higher bandwidth.
Measuring bandwidth of single-stream IPv4 TCP traffic over IPv6
GRE tap while GRO is not set on the native.
NIC: ConnectX-4LX
Before (GRO not working) : 7.2 Gbits/sec
After (GRO working): 10.5 Gbits/sec
Signed-off-by: Maria Pasechnik <mariap@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A KASAN:use-after-free bug was found related to ip6-erspan
while running selftests/net/ip6_gre_headroom.sh
It happens because of following sequence:
- ipv6hdr pointer is obtained from skb
- skb_cow_head() is called, skb->head memory is reallocated
- old data is accessed using ipv6hdr pointer
skb_cow_head() call was added in e41c7c68ea ("ip6erspan: make sure
enough headroom at xmit."), but looking at the history there was a
chance of similar bug because gre_handle_offloads() and pskb_trim()
can also reallocate skb->head memory. Fixes tag points to commit
which introduced possibility of this bug.
This patch moves ipv6hdr pointer assignment after skb_cow_head() call.
Fixes: 5a963eb61b ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the tunnel option type stored in tunnel flags when creating options
for tunnels. Thereby ensuring we do not set geneve, vxlan or erspan tunnel
options on interfaces that are not associated with them.
Make sure all users of the infrastructure set correct flags, for the BPF
helper we have to set all bits to keep backward compatibility.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ip6gre and ip6erspan share single metadata mode device,
using 'collect_md_tun'. Thus, when doing:
ip link add dev ip6gre11 type ip6gretap external
ip link add dev ip6erspan12 type ip6erspan external
RTNETLINK answers: File exists
simply fails due to the 2nd tries to create the same collect_md_tun.
The patch fixes it by adding a separate collect md tunnel device
for the ip6erspan, 'collect_md_tun_erspan'. As a result, a couple
of places need to refactor/split up in order to distinguish ip6gre
and ip6erspan.
First, move the collect_md check at ip6gre_tunnel_{unlink,link} and
create separate function {ip6gre,ip6ersapn}_tunnel_{link_md,unlink_md}.
Then before link/unlink, make sure the link_md/unlink_md is called.
Finally, a separate ndo_uninit is created for ip6erspan. Tested it
using the samples/bpf/test_tunnel_bpf.sh.
Fixes: ef7baf5e08 ("ip6_gre: add ip6 erspan collect_md mode")
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though ip6erspan_tap_init() sets up hlen and tun_hlen according to
what ERSPAN needs, it goes ahead to call ip6gre_tnl_link_config() which
overwrites these settings with GRE-specific ones.
Similarly for changelink callbacks, which are handled by
ip6gre_changelink() calls ip6gre_tnl_change() calls
ip6gre_tnl_link_config() as well.
The difference ends up being 12 vs. 20 bytes, and this is generally not
a problem, because a 12-byte request likely ends up allocating more and
the extra 8 bytes are thus available. However correct it is not.
So replace the newlink and changelink callbacks with an ERSPAN-specific
ones, reusing the newly-introduced _common() functions.
Fixes: 5a963eb61b ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract from ip6gre_changelink() a reusable function
ip6gre_changelink_common(). This will allow introduction of
ERSPAN-specific _changelink() function with not a lot of code
duplication.
Fixes: 5a963eb61b ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract from ip6gre_newlink() a reusable function
ip6gre_newlink_common(). The ip6gre_tnl_link_config() call needs to be
made customizable for ERSPAN, thus reorder it with calls to
ip6_tnl_change_mtu() and dev_hold(), and extract the whole tail to the
caller, ip6gre_newlink(). Thus enable an ERSPAN-specific _newlink()
function without a lot of duplicity.
Fixes: 5a963eb61b ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split a reusable function ip6gre_tnl_copy_tnl_parm() from
ip6gre_tnl_change(). This will allow ERSPAN-specific code to
reuse the common parts while customizing the behavior for ERSPAN.
Fixes: 5a963eb61b ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function ip6gre_tnl_link_config() is used for setting up
configuration of both ip6gretap and ip6erspan tunnels. Split the
function into the common part and the route-lookup part. The latter then
takes the calculated header length as an argument. This split will allow
the patches down the line to sneak in a custom header length computation
for the ERSPAN tunnel.
Fixes: 5a963eb61b ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ERSPAN only support version 1 and 2. When packets send to an
erspan device which does not have proper version number set,
drop the packet. In real case, we observe multicast packets
sent to the erspan pernet device, erspan0, which does not have
erspan version configured.
Reported-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the truncated bit is set only when 1) the mirrored packet
is larger than mtu and 2) the ipv4 packet tot_len is larger than
the actual skb->len. This patch adds another case for detecting
whether ipv6 packet is truncated or not, by checking the ipv6 header
payload_len and the skb->len.
Reported-by: Xiaoyan Jin <xiaoyanj@vmware.com>
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add GRO capability for IPv6 GRE tunnel and ip6erspan tap, via gro_cells
infrastructure.
Performance testing: 55% higher badwidth.
Measuring bandwidth of 1 thread IPv4 TCP traffic over IPv6 GRE tunnel
while GRO on the physical interface is disabled.
CPU: Intel Xeon E312xx (Sandy Bridge)
NIC: Mellanox Technologies MT27700 Family [ConnectX-4]
Before (GRO not working in tunnel) : 2.47 Gbits/sec
After (GRO working in tunnel) : 3.85 Gbits/sec
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function name is wrong in ip6gre_tnl_addr_conflict() comment, which
use ip6_tnl_addr_conflict instead of ip6gre_tnl_addr_conflict.
Signed-off-by: Sun Lianwen <sunlw.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the truncated bit is set only when the mirrored packet
is larger than mtu. For certain cases, the packet might already
been truncated before sending to the erspan tunnel. In this case,
the patch detect whether the IP header's total length is larger
than the actual skb->len. If true, this indicated that the
mirrored packet is truncated and set the erspan truncate bit.
I tested the patch using bpf_skb_change_tail helper function to
shrink the packet size and send to erspan tunnel.
Reported-by: Xiaoyan Jin <xiaoyanj@vmware.com>
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'tunnel' was already set at the start of ip6erspan_tap_init().
Fixes: 5a963eb61b ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronous pernet_operations are not allowed anymore.
All are asynchronous. So, drop the structure member.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current logic of flags | TUNNEL_SEQ is always non-zero and hence
sequence numbers are always incremented no matter the setting of the
TUNNEL_SEQ bit. Fix this by using & instead of |.
Detected by CoverityScan, CID#1466039 ("Operands don't affect result")
Fixes: 77a5196a80 ("gre: add sequence number for collect md mode.")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds skb_cow_header() to ensure enough headroom
at ip6erspan_tunnel_xmit before pushing the erspan header
to the skb.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When users fill in incorrect erspan version number through
the struct erspan_metadata uapi, current code skips pushing
the erspan header but continue pushing the gre header, which
is incorrect. The patch fixes it by returning error.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds the erspan v2 proto in ip6gre_tunnel_lookup
so the erspan v2 tunnel can be found correctly.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fallback tunnels (like tunl0, gre0, gretap0, erspan0, sit0,
ip6tnl0, ip6gre0) are automatically created when the corresponding
module is loaded.
These tunnels are also automatically created when a new network
namespace is created, at a great cost.
In many cases, netns are used for isolation purposes, and these
extra network devices are a waste of resources. We are using
thousands of netns per host, and hit the netns creation/delete
bottleneck a lot. (Many thanks to Kirill for recent work on this)
Add a new sysctl so that we can opt-out from this automatic creation.
Note that these tunnels are still created for the initial namespace,
to be the least intrusive for typical setups.
Tested:
lpk43:~# cat add_del_unshare.sh
for i in `seq 1 40`
do
(for j in `seq 1 100` ; do unshare -n /bin/true >/dev/null ; done) &
done
wait
lpk43:~# echo 0 >/proc/sys/net/core/fb_tunnels_only_for_init_net
lpk43:~# time ./add_del_unshare.sh
real 0m37.521s
user 0m0.886s
sys 7m7.084s
lpk43:~# echo 1 >/proc/sys/net/core/fb_tunnels_only_for_init_net
lpk43:~# time ./add_del_unshare.sh
real 0m4.761s
user 0m0.851s
sys 1m8.343s
lpk43:~#
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently GRE sequence number can only be used in native
tunnel mode. This patch adds sequence number support for
gre collect metadata mode. RFC2890 defines GRE sequence
number to be specific to the traffic flow identified by the
key. However, this patch does not implement per-key seqno.
The sequence number is shared in the same tunnel device.
That is, different tunnel keys using the same collect_md
tunnel share single sequence number.
Signed-off-by: William Tu <u9012063@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 does path selection for multipath routes deep in the lookup
functions. The next patch adds L4 hash option and needs the skb
for the forward path. To get the skb to the relevant FIB lookup
functions it needs to go through the fib rules layer, so add a
lookup_data argument to the fib_lookup_arg struct.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Determining whether a device is a GRE device is easily done by
inspecting struct net_device.type. However, for the tap variants, the
type is just ARPHRD_ETHER.
Therefore introduce two predicate functions that use netdev_ops to tell
the tap devices.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations are similar to bond_net_ops. Exit method
unregisters all net ip6gre devices, and it looks like another
pernet_operations are not interested in foreign net ip6gre list
or net_generic()->tunnels_wc. Init method registers net device.
So, it's possible to mark them async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an erspan tunnel device receives an erpsan packet with different
tunnel metadata (ex: version, index, hwid, direction), existing code
overwrites the tunnel device's erspan configuration with the received
packet's metadata. The patch fixes it.
Fixes: 1a66a836da ("gre: add collect_md mode to ERSPAN tunnel")
Fixes: f551c91de2 ("net: erspan: introduce erspan v2 for ip_gre")
Fixes: ef7baf5e08 ("ip6_gre: add ip6 erspan collect_md mode")
Fixes: 94d7d8f292 ("ip6_gre: add erspan v2 support")
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d350a82302 ("net: erspan: create erspan metadata uapi header")
moves the erspan 'version' in front of the 'struct erspan_md2' for
later extensibility reason. This breaks the existing erspan metadata
extraction code because the erspan_md2 then has a 4-byte offset
to between the erspan_metadata and erspan_base_hdr. This patch
fixes it.
Fixes: 1a66a836da ("gre: add collect_md mode to ERSPAN tunnel")
Fixes: ef7baf5e08 ("ip6_gre: add ip6 erspan collect_md mode")
Fixes: 1d7e2ed22f ("net: erspan: refactor existing erspan code")
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally the erspan fields are defined as a group into a __be16 field,
and use mask and offset to access each field. This is more costly due to
calling ntohs/htons. The patch changes it to use bitfields.
Signed-off-by: William Tu <u9012063@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BPF verifier conflict was some minor contextual issue.
The TUN conflict was less trivial. Cong Wang fixed a memory leak of
tfile->tx_array in 'net'. This is an skb_array. But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b05229f442 ("gre6: Cleanup GREv6 transmit path,
call common GRE functions") moved dev->mtu initialization
from ip6gre_tunnel_setup() to ip6gre_tunnel_init(), as a
result, the previously set values, before ndo_init(), are
reset in the following cases:
* rtnl_create_link() can update dev->mtu from IFLA_MTU
parameter.
* ip6gre_tnl_link_config() is invoked before ndo_init() in
netlink and ioctl setup, so ndo_init() can reset MTU
adjustments with the lower device MTU as well, dev->mtu
and dev->hard_header_len.
Not applicable for ip6gretap because it has one more call
to ip6gre_tnl_link_config(tunnel, 1) in ip6gre_tap_init().
Fix the first case by updating dev->mtu with 'tb[IFLA_MTU]'
parameter if a user sets it manually on a device creation,
and fix the second one by moving ip6gre_tnl_link_config()
call after register_netdevice().
Fixes: b05229f442 ("gre6: Cleanup GREv6 transmit path, call common GRE functions")
Fixes: db2ec95d1b ("ip6_gre: Fix MTU setting")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/ip6_gre.c is a case of parallel adds.
include/trace/events/tcp.h is a little bit more tricky. The removal
of in-trace-macro ifdefs in 'net' paralleled with moving
show_tcp_state_name and friends over to include/trace/events/sock.h
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'md' is allocated from 'tun_dst = ip_tun_rx_dst' and
since we've checked 'tun_dst', 'md' will never be NULL.
The patch removes it at both ipv4 and ipv6 erspan.
Fixes: afb4c97d90 ("ip6_gre: fix potential memory leak in ip6erspan_rcv")
Fixes: 50670b6ee9 ("ip_gre: fix potential memory leak in erspan_rcv")
Cc: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ip6gre is created using ioctl, its features, such as
scatter-gather, GSO and tx-checksumming will be turned off:
# ip -f inet6 tunnel add gre6 mode ip6gre remote fd00::1
# ethtool -k gre6 (truncated output)
tx-checksumming: off
scatter-gather: off
tcp-segmentation-offload: off
generic-segmentation-offload: off [requested on]
But when netlink is used, they will be enabled:
# ip link add gre6 type ip6gre remote fd00::1
# ethtool -k gre6 (truncated output)
tx-checksumming: on
scatter-gather: on
tcp-segmentation-offload: on
generic-segmentation-offload: on
This results in a loss of performance when gre6 is created via ioctl.
The issue was found with LTP/gre tests.
Fix it by moving the setup of device features to a separate function
and invoke it with ndo_init callback because both netlink and ioctl
will eventually call it via register_netdevice():
register_netdevice()
- ndo_init() callback -> ip6gre_tunnel_init() or ip6gre_tap_init()
- ip6gre_tunnel_init_common()
- ip6gre_tnl_init_features()
The moved code also contains two minor style fixes:
* removed needless tab from GRE6_FEATURES on NETIF_F_HIGHDMA line.
* fixed the issue reported by checkpatch: "Unnecessary parentheses around
'nt->encap.type == TUNNEL_ENCAP_NONE'"
Fixes: ac4eb009e4 ("ip6gre: Add support for basic offloads offloads excluding GSO")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of overlapping changes. Also on the net-next side
the XDP state management is handled more in the generic
layers so undo the 'net' nfp fix which isn't applicable
in net-next.
Include a necessary change by Jakub Kicinski, with log message:
====================
cls_bpf no longer takes care of offload tracking. Make sure
netdevsim performs necessary checks. This fixes a warning
caused by TC trying to remove a filter it has not added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Bianconi