Commit Graph

311 Commits

Author SHA1 Message Date
Gustavo F. Padovan 105721328f Bluetooth: Fix HCI_RESET command synchronization
We can't send new commands before a cmd_complete for the HCI_RESET command
shows up.

Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Reported-by: Ed Tomlinson <edt@aei.ca>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Tested-by: Ed Tomlinson <edt@aei.ca>
2011-03-31 14:25:25 -03:00
Johan Hedberg 80a1e1dbf6 Bluetooth: Add local Extended Inquiry Response (EIR) support
This patch adds automated creation of the local EIR data based on what
16-bit UUIDs are registered and what the device name is. This should
cover the majority use cases, however things like 32/128-bit UUIDs, TX
power and Device ID will need to be added later to be on par with what
bluetoothd is capable of doing (without the Management interface).

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-03-31 14:22:58 -03:00
Gustavo F. Padovan f3dd4f0f58 Bluetooth: Remove unused struct l2cap_conn item
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-03-31 14:22:57 -03:00
Szymon Janc 2763eda6cc Bluetooth: Add add/remove_remote_oob_data management commands
This patch adds commands to add and remove remote OOB data to the managment
interface. Remote data is stored in kernel and can be used by corresponding
HCI commands and events when needed.

Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-03-31 14:22:57 -03:00
Szymon Janc c35938b2f5 Bluetooth: Add read_local_oob_data management command
This patch adds a command to read local OOB data to the managment interface.
The command maps directly to the Read Local OOB Data HCI command.

Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-03-31 14:22:57 -03:00
Gustavo F. Padovan b0d2199d6f Bluetooth: Remove unused struct item
num in struct l2cap_chan_list isn't used anywhere.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-03-31 14:22:54 -03:00
Johan Hedberg b312b161ec Bluetooth: mgmt: Add support for setting the local name
This patch adds a new set_local_name management command as well as a
local_name_changed management event. With these user space can both
change the local name as well as monitor changes to it by others.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-03-31 14:22:54 -03:00
Johan Hedberg dc4fe30b86 Bluetooth: mgmt: Add local name information to read_info reply
This patch adds the name of the adapter to the reply of the read_info
management command.

The management messages reserve 249 bytes for the name instead of 248
(like in the HCI spec) so that there is always a guarantee that it is
nul-terminated. That way it can safely be passed onto string
manipulation functions.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-03-31 14:22:54 -03:00
Johan Hedberg 1f6c6378c5 Bluetooth: Add define for the maximum name length on HCI level
This patch adds a clear define for the maximum device name length in HCI
messages and thereby avoids magic numbers in the code.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-03-31 14:22:54 -03:00
Szymon Janc 4e51eae9cd Bluetooth: Move index to common header in management interface
Most mgmt commands and event are related to hci adapter. Moving index to
common header allow to easily use it in command status while reporting errors.
For those not related to adapter use MGMT_INDEX_NONE (0xFFFF) as index.

Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-27 16:56:41 -03:00
Johan Hedberg 2a61169209 Bluetooth: Add mgmt_auth_failed event
To properly track bonding completion an event to indicate authentication
failure is needed. This event will be sent whenever an authentication
complete HCI event with a non-zero status comes. It will also be sent
when we're acting in acceptor role for SSP authentication in which case
the controller will send a Simple Pairing Complete event.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-21 17:22:44 -03:00
Johan Hedberg ac56fb13c0 Bluetooth: Fix mgmt_pin_code_reply return parameters
The command complete event for mgmt_pin_code_reply &
mgmt_pin_code_neg_reply should have the adapter index, Bluetooth address
as well as the status.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-21 17:22:44 -03:00
Johan Hedberg a5c296832b Bluetooth: Add management support for user confirmation request
This patch adds support for the user confirmation (numeric comparison)
Secure Simple Pairing authentication method.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-21 17:22:44 -03:00
Johan Hedberg e9a416b5ce Bluetooth: Add mgmt_pair_device command
This patch adds a new mgmt_pair_device which can be used to initiate a
dedicated bonding procedure. Some extra callbacks are added to the
hci_conn struct so that the pairing code can get notified of the
completion of the procedure.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-21 17:22:43 -03:00
Szymon Janc adc4266d87 Bluetooth: Fix some code style issues in hci_core.h
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-17 13:30:04 -03:00
Claudio Takahasi 2ce603ebe1 Bluetooth: Send LE Connection Update Command
If the new connection update parameter are accepted, the LE master
host sends the LE Connection Update Command to its controller informing
the new requested parameters.

Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-16 20:13:21 -03:00
Ville Tervo 6bd32326cd Bluetooth: Use proper timer for hci command timout
Use proper timer instead of hci command flow control to timeout
failed hci commands. Otherwise stack ends up sending commands
when flow control is used to block new commands.

2010-09-01 18:29:41.592132 < HCI Command: Remote Name Request (0x01|0x0019) plen 10
    bdaddr 00:16:CF:E1:C7:D7 mode 2 clkoffset 0x0000
2010-09-01 18:29:41.592681 > HCI Event: Command Status (0x0f) plen 4
    Remote Name Request (0x01|0x0019) status 0x00 ncmd 0
2010-09-01 18:29:51.022033 < HCI Command: Remote Name Request Cancel (0x01|0x001a) plen 6
    bdaddr 00:16:CF:E1:C7:D7

Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-16 16:33:26 -03:00
Claudio Takahasi de73115a7d Bluetooth: Add connection parameter update response
Implements L2CAP Connection Parameter Update Response defined in
the Bluetooth Core Specification, Volume 3, Part A, section 4.21.
Address the LE Connection Parameter Procedure initiated by the slave.

Connection Interval Minimum and Maximum have the same range: 6 to
3200. Time = N * 1.25ms. Minimum shall be less or equal to Maximum.
The Slave Latency field shall have a value in the range of 0 to
((connSupervisionTimeout / connIntervalMax) - 1). Latency field shall
be less than 500. connSupervisionTimeout = Timeout Multiplier * 10 ms.
Multiplier field shall have a value in the range of 10 to 3200.

Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-16 16:33:24 -03:00
Claudio Takahasi 3300d9a930 Bluetooth: Add LE signaling commands handling
This patch splits the L2CAP command handling function in order to
have a clear separation between the commands related to BR/EDR and
LE. Commands and responses in the LE signaling channel are not being
handled yet, command reject is sent to all received requests. Bluetooth
Core Specification, Volume 3, Part A, section 4 defines the signaling
packets formats and allowed commands/responses over the LE signaling
channel.

Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-16 16:33:23 -03:00
Ville Tervo aff2cae354 Bluetooth: Add SMP command structures
Add command structures for security manager protocol.

Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-16 16:33:19 -03:00
Ville Tervo b62f328b8f Bluetooth: Add server socket support for LE connection
Add support for LE server sockets.

Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-16 16:33:02 -03:00
Ville Tervo acd7d37085 Bluetooth: Add LE connection support to L2CAP
Add basic LE connection support to L2CAP. LE
connection can be created by specifying cid
in struct sockaddr_l2

Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-16 16:32:55 -03:00
Ville Tervo 6ed58ec520 Bluetooth: Use LE buffers for LE traffic
Bluetooth chips may have separate buffers for LE traffic.
This patch add support to use LE buffers provided by the chip.

Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-16 16:32:51 -03:00
Ville Tervo fcd89c09a5 Bluetooth: Add LE connect support
Bluetooth V4.0 adds support for Low Energy (LE) connections.
Specification introduces new set of hci commands to control LE
connection. This patch adds logic to create, cancel and disconnect
LE connections.

Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-16 16:32:45 -03:00
Ville Tervo 63185f64ef Bluetooth: Add low energy commands and events
Add needed HCI command and event structs to
create LE connections.

Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-16 16:32:15 -03:00
Gustavo F. Padovan c531a12ae6 Bluetooth: remove l2cap_load() hack
l2cap_load() was added to trigger l2cap.ko module loading from the RFCOMM
and BNEP modules. Now that L2CAP module is gone, we don't need it anymore.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-15 09:45:52 -03:00
Gustavo F. Padovan 642745184f Bluetooth: Merge L2CAP and SCO modules into bluetooth.ko
Actually doesn't make sense have these modules built separately.
The L2CAP layer is needed by almost all Bluetooth protocols and profiles.
There isn't any real use case without having L2CAP loaded.
SCO is only essential for Audio transfers, but it is so small that we can
have it loaded always in bluetooth.ko without problems.
If you really doesn't want it you can disable SCO in the kernel config.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-14 17:27:36 -03:00
Gustavo F. Padovan 6de0702b5b Bluetooth: move __l2cap_sock_close() to l2cap_sock.c
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:46:02 -02:00
Gustavo F. Padovan fd83ccdb39 Bluetooth: move l2cap_sock_sendmsg() to l2cap_sock.c
Also moves some L2CAP sending functions declaration to l2cap.h

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:43:31 -02:00
Gustavo F. Padovan dcba0dba54 Bluetooth: move l2cap_sock_shutdown() to l2cap_sock.c
Declare __l2cap_wait_ack() and  l2cap_sock_clear_timer() in l2cap.h

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:43:31 -02:00
Gustavo F. Padovan 6898325923 Bluetooth: move l2cap_sock_recvmsg() to l2cap_sock.c
It causes the move of the declaration of 3 functions to l2cap.h:
l2cap_get_ident(), l2cap_send_cmd(), l2cap_build_conf_req()

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:43:31 -02:00
Gustavo F. Padovan 4e34c50bfe Bluetooth: move l2cap_sock_connect() to l2cap_sock.c
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:43:31 -02:00
Gustavo F. Padovan 99f4808db0 Bluetooth: move l2cap_sock_getsockopt() to l2cap_sock.c
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:43:31 -02:00
Gustavo F. Padovan 33575df7be Bluetooth: move l2cap_sock_setsockopt() to l2cap_sock.c
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:43:31 -02:00
Gustavo F. Padovan d7175d5525 Bluetooth: move l2cap_sock_getname() to l2cap_sock.c
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:43:30 -02:00
Gustavo F. Padovan c47b7c724b Bluetooth: move l2cap_sock_accept() to l2cap_sock.c
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:43:30 -02:00
Gustavo F. Padovan af6bcd8205 Bluetooth: move l2cap_sock_bind()/listen() to l2cap_sock.c
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:43:30 -02:00
Gustavo F. Padovan 554f05bb8a Bluetooth: move l2cap_sock_release() to l2cap_sock.c
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:43:30 -02:00
Gustavo F. Padovan 65390587c7 Bluetooth: move l2cap_sock_ops to l2cap_sock.c
First step to move all l2cap_sock_ops function to l2cap_sock.c

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:43:30 -02:00
Gustavo F. Padovan bb58f747e5 Bluetooth: Initial work for L2CAP split.
This patch tries to do the minimal to move l2cap_sock_create() and its
dependencies to l2cap_sock.c. It create a API to initialize and cleanup
the L2CAP sockets from l2cap_core.c through l2cap_init_sockets() and
l2cap_cleanup_sockets().

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:43:30 -02:00
Johan Hedberg 17fa4b9dff Bluetooth: Add set_io_capability management command
This patch adds a new set_io_capability management command which is used
to set the IO capability for Secure Simple Pairing (SSP) as well as the
Security Manager Protocol (SMP). The value is per hci_dev and each
hci_conn object inherits it upon creation.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:08 -02:00
Johan Hedberg 980e1a537f Bluetooth: Add support for PIN code handling in the management interface
This patch adds the necessary commands and events needed to communicate
PIN code related actions between the kernel and userspace. This includes
a pin_code_request event as well as pin_code_reply and
pin_code_negative_reply commands.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:07 -02:00
Johan Hedberg 2784eb41b1 Bluetooth: Add get_connections managment interface command
This patch adds a get_connections command to the management interface.
With this command userspace can get the current list of connected
devices. Typically this command would only be used once when enumerating
existing adapters. After that the connected and disconnected events are
used to track connections.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:07 -02:00
Johan Hedberg 17d5c04cb5 Bluetooth: Add support for connect failed management event
This patch add a new connect failed management event to track failures
in connecting to remote devices. It is particularly useful for security
mode 3 scenarios when we don't have a connected state while pairing but
still need to detect when the connect attempt failed.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:07 -02:00
Johan Hedberg 8962ee74be Bluetooth: Add disconnect managment command
This patch adds a disconnect command to the managment interface. Using
this command user space is able to force the disconnection of connected
devices. The command maps directly to the Disconnect HCI command.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:07 -02:00
Johan Hedberg f7520543ab Bluetooth: Add connected/disconnected management events
This patch adds connected and disconnected managment events to track the
connection status to remote devices. The events map directly to
successful connection complete and disconnection complete HCI events for
ACL links.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:07 -02:00
Johan Hedberg 55ed8ca10f Bluetooth: Implement link key handling for the management interface
This patch adds a management commands to feed the kernel with all stored
link keys as well as remove specific ones or all of them. Once the
load_keys command has been called the kernel takes over link key
replies. A new_key event is also added to inform userspace of newly
created link keys that should be stored permanently.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:07 -02:00
Johan Hedberg 1aff6f0949 Bluetooth: Add class of device control to the management interface
This patch adds the possibility for user space to fully control the
Class of Device value of local adapters. To control the service class
bits each UUID that's added comes with a service class "hint" which acts
as a mask of bits that the UUID needs to have enabled. The
set_service_cache management command is used to make sure we queue up
all UUID changes as user space initializes its drivers and then send a
single HCI_Write_Class_of_Device command when initialization is
complete.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:06 -02:00
Johan Hedberg d5859e22cd Bluetooth: Implement a more complete adapter initialization sequence
Using the managment interface means that user space doesn't need to do
any HCI command sending at all. This patch moves the remaining
initialization commands from user space to the kernel side. The patch
makes use of the new feature of __hci_request which allows the request
to be dynamically modified while it is ongoing (something that is needed
to react appropriately to the local features and the version of the
adapter).

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:06 -02:00
Johan Hedberg b0916ea0d9 Bluetooth: Add controller side link key clearing to hci_init_req
The controller may have link keys in its own memory and these keys could
be used for secure connections. However, since the interface to access
these keys doesn't provide information about the key types (which would
be needed to infer the level of security each key provides) using these
keys is rather useless. Therefore, simply clear the controller side list
in the initialization procedure.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:06 -02:00
Johan Hedberg a5040efa20 Bluetooth: Add special handling with __hci_request and HCI_INIT
To support a more dynamic HCI initialization sequence the __hci_request
behavior requires some more changes. Particularly, the init sequence
should be able to have conditionals in it (sending some HCI commands
depending on the outcome of a previous command) instead of being a fixed
list as it is right now.

The reasons for these additional requirements are the moving all
previously user space driven initialization commands to the kernel side
as well as the support the Low Energy controllers.

To fulfull these requirements the init sequence is made the only special
case for multi-command requests and req_last_cmd is renamed to
init_last_cmd. The hci_send_cmd function is changed to update
init_last_cmd as long as the HCI_INIT flag is set.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:06 -02:00
Johan Hedberg 03b555e119 Bluetooth: Reject pairing requests when in non-pairable mode
This patch adds the necessary logic to act accordingly when the
HCI_PAIRABLE flag is not set. In that case PIN code replies as well as
Secure Simple Pairing requests without a NoBonding requirement need to
be rejected.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:06 -02:00
Johan Hedberg 2aeb9a1ae0 Bluetooth: Implement UUID handling through the management interface
This patch adds methods to the management interface for userspace to
notify the kernel of which services have been registered for specific
adapters. This information is needed for setting the appropriate Class
of Device value as well as the Extended Inquiry Response value. This
patch doesn't actually implement setting of these values but just
provides the storage of the UUIDs so the needed functionality can be
built on top of it.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:05 -02:00
Johan Hedberg c542a06c29 Bluetooth: Implement set_pairable managment command
This patch implements a new set_pairable management command to control
the pairable state of local adapters. The state is represented using a
new HCI_PAIRABLE flag in the hci_dev struct.

For backwards compatibility with older user space versions the
HCI_PAIRABLE flag gets automatically set when the existence of an
adapter is reported to user space through legacy methods and the
HCI_MGMT flag is not set.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:05 -02:00
Johan Hedberg ebc99feba7 Bluetooth: Add flag to track managment controlled adapters
This patch adds a HCI_MGMT flag to track adapters which are under the
control of the management interface. This is needed to make sure that
new kernels will work with old user space versions. I.e. behaviour which
could break old user space versions (but is needed by the management
interface) should not be exhibited when the HCI_MGMT flag is not set.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:05 -02:00
Johan Hedberg 72a734ec1a Bluetooth: Unify mode related management messages to a single struct
The powered, connectable and discoverable messages all have the same
format. By using a single struct for all of them a lot of code can be
simplified and reused.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:05 -02:00
Johan Hedberg 9fbcbb455d Bluetooth: Add set_connectable management command
This patch adds a set_connectable command as well as a corresponding
event to the management interface. It's mainly useful for setting an
adapter as connectable from a non-initialized state as well as setting
an already initialized adapter as non-connectable (mostly useful for
qualification purposes).

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:05 -02:00
Johan Hedberg 73f22f6238 Bluetooth: Add support for set_discoverable management command
This patch adds a set_discoverable command to the management interface
as well as the corresponding event. The command is used to control the
discoverable state of adapters.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:04 -02:00
Johan Hedberg eec8d2bcc8 Bluetooth: Add support for set_powered management command
This patch adds a set_powered command to the management interface
through which the powered state of local adapters can be controlled.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:04 -02:00
Johan Hedberg 5add6af8fc Bluetooth: Add support for management powered event
This patch adds support for the powered event that's used to indicate to
userspace when the powered state of a local adapter changes.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:04 -02:00
Johan Hedberg ab81cbf99c Bluetooth: Implement automatic setup procedure for local adapters
This patch implements automatic initialization of basic information
about newly registered Bluetooth adapters. E.g. the address and features
are always needed so it makes sense for the kernel to automatically
power on adapters and read this information. A new HCI_SETUP flag is
added to track this state.

In order to not consume unnecessary amounts of power if there isn't a
user space available that could switch the adapter back off, a timer is
added to do this automatically as long as no Bluetooth user space seems
to be present. A new HCI_AUTO_OFF flag is added that user space needs to
clear to avoid the automatic power off.

Additionally, the management interface index_added event is moved to the
end of the HCI_SETUP stage so a user space supporting the managment
inteface has all the necessary information available for fetching when
it gets notified of a new adapter. The HCI_DEV_REG event is kept in the
same place as before since existing HCI raw socket based user space
versions depend on seeing the kernels initialization sequence
(hci_init_req) to determine when the adapter is ready for use.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:04 -02:00
Andrei Emeltchenko e702112ff6 Bluetooth: Use non-flushable by default L2CAP data packets
Modification of Nick Pelly <npelly@google.com> patch.

With Bluetooth 2.1 ACL packets can be flushable or non-flushable. This commit
makes ACL data packets non-flushable by default on compatible chipsets, and
adds the BT_FLUSHABLE socket option to explicitly request flushable ACL
data packets for a given L2CAP socket. This is useful for A2DP data which can
be safely discarded if it can not be delivered within a short time (while
other ACL data should not be discarded).

Note that making ACL data flushable has no effect unless the automatic flush
timeout for that ACL link is changed from its default of 0 (infinite).

Default packet types (for compatible chipsets):
Frame 34: 13 bytes on wire (104 bits), 13 bytes captured (104 bits)
Bluetooth HCI H4
Bluetooth HCI ACL Packet
    .... 0000 0000 0010 = Connection Handle: 0x0002
    ..00 .... .... .... = PB Flag: First Non-automatically Flushable Packet (0)
    00.. .... .... .... = BC Flag: Point-To-Point (0)
    Data Total Length: 8
Bluetooth L2CAP Packet

After setting BT_FLUSHABLE
(sock.setsockopt(274 /*SOL_BLUETOOTH*/, 8 /* BT_FLUSHABLE */, 1 /* flush */))
Frame 34: 13 bytes on wire (104 bits), 13 bytes captured (104 bits)
Bluetooth HCI H4
Bluetooth HCI ACL Packet
    .... 0000 0000 0010 = Connection Handle: 0x0002
    ..10 .... .... .... = PB Flag: First Automatically Flushable Packet (2)
    00.. .... .... .... = BC Flag: Point-To-Point (0)
    Data Total Length: 8
Bluetooth L2CAP Packet

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-08 01:40:04 -02:00
Johan Hedberg 765c2a964b Bluetooth: Fix race condition with conn->sec_level
The conn->sec_level value is supposed to represent the current level of
security that the connection has. However, by assigning to it before
requesting authentication it will have the wrong value during the
authentication procedure. To fix this a pending_sec_level variable is
added which is used to track the desired security level while making
sure that sec_level always represents the current level of security.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-01-19 14:43:11 -02:00
Johan Hedberg 23bb57633d Bluetooth: Fix __hci_request synchronization for hci_open_dev
The initialization function used by hci_open_dev (hci_init_req) sends
many different HCI commands. The __hci_request function should only
return when all of these commands have completed (or a timeout occurs).
Several of these commands cause hci_req_complete to be called which
causes __hci_request to return prematurely.

This patch fixes the issue by adding a new hdev->req_last_cmd variable
which is set during the initialization procedure. The hci_req_complete
function will no longer mark the request as complete until the command
matching hdev->req_last_cmd completes.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-12-22 22:58:07 -02:00
Johan Hedberg c71e97bfaa Bluetooth: Add management events for controller addition & removal
This patch adds Bluetooth Management interface events for controller
addition and removal. The events correspond to the existing HCI_DEV_REG
and HCI_DEV_UNREG stack internal events.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-12-22 22:58:00 -02:00
Johan Hedberg f7b64e69c7 Bluetooth: Add read_info management command
This patch implements the read_info command which is used to fetch basic
info about an adapter.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-12-22 22:57:51 -02:00
Johan Hedberg faba42eb2a Bluetooth: Add read_index_list management command
This patch implements the read_index_list command through which
userspace can get a list of current adapter indices.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-12-22 22:57:44 -02:00
Johan Hedberg 02d981292a Bluetooth: Add read_version management command
This patch implements the initial read_version command that userspace
will use before any other management interface operations.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-12-22 22:57:37 -02:00
Johan Hedberg a40c406cbd Bluetooth: Make hci_send_to_sock usable for management control sockets
In order to send data to management control sockets the function should:

  - skip checks intended for raw HCI data and stack internal events
  - make sure RAW HCI data or stack internal events don't go to
    management control sockets

In order to accomplish this the patch adds a new member to the bluetooth
skb private data to flag skb's that are destined for management control
sockets.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-12-07 23:03:39 -02:00
Johan Hedberg 0381101fd6 Bluetooth: Add initial Bluetooth Management interface callbacks
Add initial code for handling Bluetooth Management interface messages.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-12-07 23:03:38 -02:00
Johan Hedberg c02178d22b Bluetooth: Add Bluetooth Management interface definitions
Add initial definitions for the new Bluetooth Management interface to
the bluetooth headers.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-12-07 22:59:54 -02:00
Andrei Emeltchenko be21871f24 Bluetooth: clean up legal text
Remove extra spaces from legal text so that legal stuff looks
the same for all bluetooth code.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-12-01 21:04:43 -02:00
Andrei Emeltchenko 70f23020e6 Bluetooth: clean up hci code
Do not use assignment in IF condition, remove extra spaces,
fixing typos, simplify code.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-12-01 21:04:43 -02:00
Andrei Emeltchenko 894718a6be Bluetooth: clean up l2cap code
Do not initialize static vars to zero, macros with complex values
shall be enclosed with (), remove unneeded braces.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-12-01 21:04:43 -02:00
Andrei Emeltchenko 285b4e9031 Bluetooth: clean up rfcomm code
Remove extra spaces, assignments in if statement, zeroing static
variables, extra braces. Fix includes.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-12-01 21:04:43 -02:00
Andrei Emeltchenko 735cbc4784 Bluetooth: clean up sco code
Do not use assignments in IF condition, remove extra spaces

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-12-01 21:04:43 -02:00
Andrei Emeltchenko 534c92fde7 Bluetooth: clean up rfcomm code
Remove dead code and unused rfcomm thread events

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-10-12 12:44:53 -03:00
Mat Martineau 796c86eec8 Bluetooth: Add common code for stream-oriented recvmsg()
This commit adds a bt_sock_stream_recvmsg() function for use by any
Bluetooth code that uses SOCK_STREAM sockets.  This code is copied
from rfcomm_sock_recvmsg() with minimal modifications to remove
RFCOMM-specific functionality and improve readability.

L2CAP (with the SOCK_STREAM socket type) and RFCOMM have common needs
when it comes to reading data.  Proper stream read semantics require
that applications can read from a stream one byte at a time and not
lose any data.  The RFCOMM code already operated on and pulled data
from the underlying L2CAP socket, so very few changes were required to
make the code more generic for use with non-RFCOMM data over L2CAP.

Applications that need more awareness of L2CAP frame boundaries are
still free to use SOCK_SEQPACKET sockets, and may verify that they
connection did not fall back to basic mode by calling getsockopt().

Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-10-12 12:44:51 -03:00
David Vrabel 8f1e174223 Bluetooth: HCI devices are either BR/EDR or AMP radios
HCI transport drivers may not know what type of radio an AMP device has
so only say whether they're BR/EDR or AMP devices.

Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-10-12 12:44:51 -03:00
David S. Miller d122179a3c Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	net/core/ethtool.c
2010-10-11 12:30:34 -07:00
Gustavo F. Padovan e454c84464 Bluetooth: Fix deadlock in the ERTM logic
The Enhanced Retransmission Mode(ERTM) is a realiable mode of operation
of the Bluetooth L2CAP layer. Think on it like a simplified version of
TCP.
The problem we were facing here was a deadlock. ERTM uses a backlog
queue to queue incomimg packets while the user is helding the lock. At
some moment the sk_sndbuf can be exceeded and we can't alloc new skbs
then the code sleep with the lock to wait for memory, that stalls the
ERTM connection once we can't read the acknowledgements packets in the
backlog queue to free memory and make the allocation of outcoming skb
successful.

This patch actually affect all users of bt_skb_send_alloc(), i.e., all
L2CAP modes and SCO.

We are safe against socket states changes or channels deletion while the
we are sleeping wait memory. Checking for the sk->sk_err and
sk->sk_shutdown make the code safe, since any action that can leave the
socket or the channel in a not usable state set one of the struct
members at least. Then we can check both of them when getting the lock
again and return with the proper error if something unexpected happens.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
2010-09-30 12:19:35 -03:00
Eric Dumazet a02cec2155 net: return operator cleanup
Change "return (EXPR);" to "return EXPR;"

return is not a function, parentheses are not required.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-23 14:33:39 -07:00
Mat Martineau db12d647cc Bluetooth: Use 3-DH5 payload size for default ERTM max PDU size
The previous value of 672 for L2CAP_DEFAULT_MAX_PDU_SIZE is based on
the default L2CAP MTU.  That default MTU is calculated from the size
of two DH5 packets, minus ACL and L2CAP b-frame header overhead.

ERTM is used with newer basebands that typically support larger 3-DH5
packets, and i-frames and s-frames have more header overhead.  With
clean RF conditions, basebands will typically attempt to use 1021-byte
3-DH5 packets for maximum throughput.  Adjusting for 2 bytes of ACL
headers plus 10 bytes of worst-case L2CAP headers yields 1009 bytes
of payload.

This PDU size imposes less overhead for header bytes and gives the
baseband the option to choose 3-DH5 packets, but is small enough for
ERTM traffic to interleave well with other L2CAP or SCO data.
672-byte payloads do not allow the most efficient over-the-air
packet choice, and cannot achieve maximum throughput over BR/EDR.

Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-08-10 07:59:11 -04:00
Mat Martineau fa235562fb Bluetooth: Change default L2CAP ERTM retransmit timeout
The L2CAP specification requires that the ERTM retransmit timeout be at
least 2 seconds for BR/EDR connections.

Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-08-10 07:59:11 -04:00
David Miller ea4bd8ba80 Bluetooth: Use list_head for HCI blacklist head
The bdaddr in the list root is completely unused and just
taking up space.

Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-07-31 16:06:58 -07:00
Marcel Holtmann e73439d8c0 Bluetooth: Defer SCO setup if mode change is pending
Certain headsets such as the Motorola H350 will reject SCO and eSCO
connection requests while the ACL is transitioning from sniff mode
to active mode. Add synchronization so that SCO and eSCO connection
requests will wait until the ACL has fully transitioned to active mode.

< HCI Command: Exit Sniff Mode (0x02|0x0004) plen 2
    handle 12
> HCI Event: Command Status (0x0f) plen 4
    Exit Sniff Mode (0x02|0x0004) status 0x00 ncmd 1
< HCI Command:  Setup Synchronous Connection (0x01|0x0028) plen 17
    handle 12 voice setting 0x0040
> HCI Event: Command Status (0x0f) plen 4
    Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
> HCI Event: Number of Completed Packets (0x13) plen 5
    handle 12 packets 1
> HCI Event: Mode Change (0x14) plen 6
    status 0x00 handle 12 mode 0x00 interval 0
    Mode: Active
> HCI Event: Synchronous Connect Complete (0x2c) plen 17
    status 0x10 handle 14 bdaddr 00:1A:0E:50:28:A4 type SCO
    Error: Connection Accept Timeout Exceeded

Signed-off-by: Ron Shaffer <rshaffer@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-07-27 12:29:04 -07:00
Gustavo F. Padovan 66c853cc21 Bluetooth: Use __packed annotation
To make net/ and include/net/ code consistent use __packed instead of
__attribute__ ((packed)). Bluetooth subsystem was one of the last net
subsys still using __attribute__ ((packed)).

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-07-21 10:39:13 -07:00
Gustavo F. Padovan 5d8868ff3d Bluetooth: Add Google's copyright to L2CAP
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-07-21 10:39:12 -07:00
Suraj Sumangala 9981151086 Bluetooth: Implemented HCI frame reassembly for RX from stream
Implemented frame reassembly implementation for reassembling fragments
received from stream.

Signed-off-by: Suraj Sumangala <suraj@atheros.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-07-21 10:39:12 -07:00
Suraj Sumangala 33e882a5f2 Bluetooth: Implement hci_reassembly helper to reassemble RX packets
Implements feature to reassemble received HCI frames from any input stream

Signed-off-by: Suraj Sumangala <suraj@atheros.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-07-21 10:39:12 -07:00
Suraj Sumangala cd4c53919e Bluetooth: Add one more buffer for HCI stream reassembly
Additional reassembly buffer to keep track of stream reasembly

Signed-off-by: Suraj Sumangala <suraj@atheros.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-07-21 10:39:12 -07:00
Gustavo F. Padovan ce5706bd69 Bluetooth: Add Copyright notice to L2CAP
Copyright for the time I worked on L2CAP during the Google Summer of Code
program.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-07-21 10:39:11 -07:00
Gustavo F. Padovan e0f66218b3 Bluetooth: Remove the send_lock spinlock from ERTM
Using a lock to deal with the ERTM race condition - interruption with
new data from the hci layer - is wrong. We should use the native skb
backlog queue.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-07-21 10:39:09 -07:00
Gustavo F. Padovan cf6c2c0b9f Bluetooth: Disconnect early if mode is not supported
When mode is mandatory we shall not send connect request and report this
to the userspace as well.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-07-21 10:39:09 -07:00
Ron Shaffer 2d0a03460a Bluetooth: Reassigned copyright to Code Aurora Forum
Qualcomm, Inc. has reassigned rights to Code Aurora Forum. Accordingly,
as files are modified by Code Aurora Forum members, the copyright
statement will be updated.

Signed-off-by: Ron Shaffer <rshaffer@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-07-21 10:39:06 -07:00
Ron Shaffer 04fafe4ed7 Bluetooth: Remove extraneous white space
Deleted extraneous white space from the end of several lines

Signed-off-by: Ron Shaffer <rshaffer@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-07-21 10:39:05 -07:00
Johan Hedberg f03585689f Bluetooth: Add blacklist support for incoming connections
In some circumstances it could be desirable to reject incoming
connections on the baseband level. This patch adds this feature through
two new ioctl's: HCIBLOCKADDR and HCIUNBLOCKADDR. Both take a simple
Bluetooth address as a parameter. BDADDR_ANY can be used with
HCIUNBLOCKADDR to remove all devices from the blacklist.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-07-21 10:39:05 -07:00
Marcel Holtmann f48fd9c8cd Bluetooth: Create per controller workqueue
Instead of having a global workqueue for all controllers, it makes
more sense to have a workqueue per controller.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-05-10 09:34:03 +02:00
Gustavo F. Padovan dfc909befb Bluetooth: Fix race condition on l2cap_ertm_send()
l2cap_ertm_send() can be called both from user context and bottom half
context. The socket locks for that contexts are different, the user
context uses a mutex(which can sleep) and the second one uses a
spinlock_bh. That creates a race condition when we have interruptions on
both contexts at the same time.

The better way to solve this is to add a new spinlock to lock
l2cap_ertm_send() and the vars it access. The other solution was to defer
l2cap_ertm_send() with a workqueue, but we the sending process already
has one defer on the hci layer. It's not a good idea add another one.

The patch refactor the code to create l2cap_retransmit_frames(), then we
encapulate the lock of l2cap_ertm_send() for some call. It also changes
l2cap_retransmit_frame() to l2cap_retransmit_one_frame() to avoid
confusion

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-05-10 09:28:53 +02:00
Gustavo F. Padovan 1890d36bb5 Bluetooth: Implement Local Busy Condition handling
Supports Local Busy condition handling through a waitqueue that wake ups
each 200ms and try to push the packets to the upper layer. If it can
push all the queue then it leaves the Local Busy state.

The patch modifies the behaviour of l2cap_ertm_reassembly_sdu() to
support retry of the push operation.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-05-10 09:28:53 +02:00
Gustavo F. Padovan 9a9c6a3441 Bluetooth: Make hci_send_acl() void
hci_send_acl can't fail, so we can make it void. This patch changes
that and all the funcions that use hci_send_acl().
That change exposed a bug on sending connectionless data. We were not
reporting the lenght send back to the user space.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-05-10 09:28:52 +02:00
Gustavo F. Padovan 68d7f0ce91 Bluetooth: Enable option to configure Max Transmission value via sockopt
With the sockopt extension we can set a per-channel MaxTx value.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-05-10 09:28:50 +02:00
Gustavo F. Padovan 803020c6fa Bluetooth: Change acknowledgement to use the value of txWindow
Now that we can set the txWindow we need to change the acknowledgement
procedure to ack after each (pi->txWindow/6 + 1). The plus 1 is to avoid
the zero value.
It also renames pi->num_to_ack to a better name: pi->num_acked.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-05-10 09:28:50 +02:00
Gustavo F. Padovan 14b5aa71ec Bluetooth: Add sockopt configuration for txWindow on L2CAP
Now we can set/get Transmission Window size via sockopt.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-05-10 09:28:49 +02:00
Gustavo F. Padovan 1c7621596d Bluetooth: Fix configuration of the MPS value
We were accepting values bigger than we can accept. This was leading
ERTM to drop packets because of wrong FCS checks.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-05-10 09:28:48 +02:00
Gustavo F. Padovan c1b4f43be0 Bluetooth: Add timer to Acknowledge I-frames
We ack I-frames on each txWindow/5 I-frames received, but if the sender
stop to send I-frames and it's not a txWindow multiple we can leave some
frames unacked.
So I added a timer to ack I-frames on this case. The timer expires in
200ms.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-05-10 09:28:48 +02:00
Gustavo F. Padovan d5392c8f1e Bluetooth: Implement 'Send IorRRorRNR' event
After receive a RR with P bit set ERTM shall use this funcion to choose
what type of frame to reply with F bit = 1.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-05-10 09:28:46 +02:00
Gustavo F. Padovan 0d861d8b8e Bluetooth: Make hci_send_sco() void
It also removes an unneeded check for the MTU. The check is done before
on sco_send_frame()

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-05-10 09:28:45 +02:00
Marcel Holtmann aef7d97cc6 Bluetooth: Convert debug files to actually use debugfs instead of sysfs
Some of the debug files ended up wrongly in sysfs, because at that point
of time, debugfs didn't exist. Convert these files to use debugfs and
also seq_file. This patch converts all of these files at once and then
removes the exported symbol for the Bluetooth sysfs class.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-03-21 05:49:35 +01:00
Marcel Holtmann 943da25d95 Bluetooth: Add controller types for BR/EDR and 802.11 AMP
With the Bluetooth 3.0 specification and the introduction of alternate
MAC/PHY (AMP) support, it is required to differentiate between primary
BR/EDR controllers and 802.11 AMP controllers. So introduce a special
type inside HCI device for differentiation.

For now all AMP controllers will be treated as raw devices until an
AMP manager has been implemented.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-02-27 14:05:38 +01:00
Marcel Holtmann ca325f6989 Bluetooth: Convert inquiry cache to use debugfs instead of sysfs
The output of the inquiry cache is only useful for debugging purposes
and so move it into debugfs.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-02-27 14:05:38 +01:00
Marcel Holtmann c13854cef4 Bluetooth: Convert controller hdev->type to hdev->bus
The hdev->type is misnamed and should be actually hdev->bus instead. So
convert it now.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-02-27 14:05:38 +01:00
Gustavo F. Padovan 4ec10d9720 Bluetooth: Implement RejActioned flag
RejActioned is used to prevent retransmission when a entity is on the
WAIT_F state, i.e., waiting for a frame with F-bit set due local busy
condition or a expired retransmission timer. (When these two events raise
they send a frame with the Poll bit set and enters in the WAIT_F state to
wait for a frame with the Final bit set.)
The local entity doesn't send I-frames(the data frames) until the receipt
of a frame with F-bit set. When that happens it also set RejActioned to false.
RejActioned is a mandatory feature of ERTM spec.

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-12-03 19:34:24 +01:00
Gustavo F. Padovan 9f121a5a80 Bluetooth: Fix sending ReqSeq on I-frames
As specified by ERTM spec an ERTM channel can acknowledge received
I-frames(the data frames) by sending an I-frame with the proper ReqSeq
value (i.e. ReqSeq is set to BufferSeq).  Until now we aren't setting the
ReqSeq value on I-frame control bits. That way we can save sending
S-frames(Supervise frames) only to acknowledge receipt of I-frames. It
is very helpful to the full-duplex channel.
ReqSeq is the packet sequence number sent in an acknowledgement frame to
acknowledge receipt of frames up to (ReqSeq - 1).
BufferSeq controls the receiver buffer, it is used to delay
acknowledgement of new frames to not cause buffer overflow. BufferSeq
value is not increased until frames are pulled by reassembly function.

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-12-03 19:34:23 +01:00
Marcel Holtmann c78ae28314 Bluetooth: Unobfuscate tasklet_schedule usage
The tasklet schedule function helpers are just an obfuscation. So remove
them and call the schedule functions directly.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-12-03 19:34:21 +01:00
Marcel Holtmann 76bca88012 Bluetooth: Turn hci_recv_frame into an exported function
For future simplification it is important that the hci_recv_frame
function is no longer an inline function. So move it into the module
itself and export it.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-12-03 19:34:20 +01:00
Stephen Hemminger ec1b4cf74c net: mark net_proto_ops as const
All usages of structure net_proto_ops should be declared const.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07 01:10:46 -07:00
Gustavo F. Padovan 2246b2f1b4 Bluetooth: Handle L2CAP case when the remote receiver is busy
Implement all issues related to RemoteBusy in the RECV state table.

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-26 00:12:20 -07:00
Luiz Augusto von Dentz 9e726b1742 Bluetooth: Fix rejected connection not disconnecting ACL link
When using DEFER_SETUP on a RFCOMM socket, a SABM frame triggers
authorization which when rejected send a DM response. This is fine
according to the RFCOMM spec:

    the responding implementation may replace the "proper" response
    on the Multiplexer Control channel with a DM frame, sent on the
    referenced DLCI to indicate that the DLCI is not open, and that
    the responder would not grant a request to open it later either.

But some stacks doesn't seems to cope with this leaving DLCI 0 open after
receiving DM frame.

To fix it properly a timer was introduced to rfcomm_session which is used
to set a timeout when the last active DLC of a session is unlinked, this
will give the remote stack some time to reply with a proper DISC frame on
DLCI 0 avoiding both sides sending DISC to each other on stacks that
follow the specification and taking care of those who don't by taking
down DLCI 0.

Signed-off-by: Luiz Augusto von Dentz <luiz.dentz@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 15:05:58 -07:00
Gustavo F. Padovan ef54fd937f Bluetooth: Full support for receiving L2CAP SREJ frames
Support for receiving of SREJ frames as specified by the state table.

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 15:03:43 -07:00
Gustavo F. Padovan 8f17154f1f Bluetooth: Add support for L2CAP SREJ exception
When L2CAP loses an I-frame we send a SREJ frame to the transmitter side
requesting the lost packet. This patch implement all Recv I-frame events
on SREJ_SENT state table except the ones that deal with SendRej (the REJ
exception at receiver side is yet not implemented).

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 15:01:25 -07:00
Gustavo F. Padovan fcc203c30d Bluetooth: Add support for FCS option to L2CAP
Implement CRC16 check for L2CAP packets. FCS is used by Streaming Mode and
Enhanced Retransmission Mode and is a extra check for the packet content.

Using CRC16 is the default, L2CAP won't use FCS only when both side send
a "No FCS" request.

Initially based on a patch from Nathan Holstein <nathan@lampreynetworks.com>

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 14:59:49 -07:00
Gustavo F. Padovan e90bac061b Bluetooth: Add support for Retransmission and Monitor Timers
L2CAP uses retransmission and monitor timers to inquiry the other side
about unacked I-frames. After sending each I-frame we (re)start the
retransmission timer. If it expires, we start a monitor timer that send a
S-frame with P bit set and wait for S-frame with F bit set. If monitor
timer expires, try again, at a maximum of L2CAP_DEFAULT_MAX_TX.

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 14:56:15 -07:00
Gustavo F. Padovan 30afb5b2aa Bluetooth: Initial support for retransmission of packets with REJ frames
When receiving an I-frame with unexpected txSeq, receiver side start the
recovery procedure by sending a REJ S-frame to the transmitter side. So
the transmitter can re-send the lost I-frame.

This patch just adds a basic support for retransmission, it doesn't
mean that ERTM now has full support for packet retransmission.

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 14:55:20 -07:00
Gustavo F. Padovan c74e560cd0 Bluetooth: Add support for Segmentation and Reassembly of SDUs
ERTM should use Segmentation and Reassembly to break down a SDU in many
PDUs on sending data to the other side.

On sending packets we queue all 'segments' until end of segmentation and
just the add them to the queue for sending. On receiving we create a new
SKB with the SDU reassembled.

Initially based on a patch from Nathan Holstein <nathan@lampreynetworks.com>

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 14:53:58 -07:00
Gustavo F. Padovan 1c2acffb76 Bluetooth: Add initial support for ERTM packets transfers
This patch adds support for ERTM transfers, without retransmission, with
txWindow up to 63 and with acknowledgement of packets received. Now the
packets are queued before call l2cap_do_send(), so packets couldn't be
sent at the time we call l2cap_sock_sendmsg(). They will be sent in
an asynchronous way on later calls of l2cap_ertm_send(). Besides if an
error occurs on calling l2cap_do_send() we disconnect the channel.

Initially based on a patch from Nathan Holstein <nathan@lampreynetworks.com>

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 14:53:01 -07:00
Gustavo F. Padovan f2fcfcd670 Bluetooth: Add configuration support for ERTM and Streaming mode
Add support to config_req and config_rsp to configure ERTM and Streaming
mode. If the remote device specifies ERTM or Streaming mode, then the
same mode is proposed. Otherwise ERTM or Basic mode is used. And in case
of a state 2 device, the remote device should propose the same mode. If
not, then the channel gets disconnected.

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 14:50:07 -07:00
Marcel Holtmann c6b03cf986 Bluetooth: Allow setting of L2CAP ERTM via socket option
To enable Enhanced Retransmission mode it needs to be set via a socket
option. A different mode can be set on a socket, but on listen() and
connect() the mode is checked and ERTM is only allowed if it is enabled
via the module parameter.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 14:50:07 -07:00
Thomas Gleixner a6a67efd70 Bluetooth: Convert hdev->req_lock to a mutex
hdev->req_lock is used as mutex so make it a mutex.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 14:35:02 -07:00
Marcel Holtmann 9eba32b86d Bluetooth: Add extra device reference counting for connections
The device model itself has no real usable reference counting at the
moment and this causes problems if parents are deleted before their
children. The device model itself handles the memory details of this
correctly, but the uevent order is not consistent. This causes various
problems for systems like HAL or even X.

So until device_put() does a proper cleanup, the device for Bluetooth
connection will be protected with an extra reference counting to ensure
the correct order of uevents when connections are terminated.

This is not an automatic feature. Higher Bluetooth layers like HIDP or
BNEP should grab this new reference to ensure that their uevents are
send before the ones from the parent device.

Based on a report by Brian Rogers <brian@xyzw.org>

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 14:19:26 -07:00
Dave Young af0d3b103b bluetooth: rfcomm_init bug fix
rfcomm tty may be used before rfcomm_tty_driver initilized,
The problem is that now socket layer init before tty layer, if userspace
program do socket callback right here then oops will happen.

reporting in:
http://marc.info/?l=linux-bluetooth&m=124404919324542&w=2

make 3 changes:
1. remove #ifdef in rfcomm/core.c,
make it blank function when rfcomm tty not selected in rfcomm.h

2. tune the rfcomm_init error patch to ensure
tty driver initilized before rfcomm socket usage.

3. remove __exit for rfcomm_cleanup_sockets
because above change need call it in a __init function.

Reported-by: Oliver Hartkopp <oliver@hartkopp.net>
Tested-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-03 13:24:39 -07:00
David S. Miller bb400801c2 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/holtmann/bluetooth-next-2.6 2009-06-11 05:47:43 -07:00
David S. Miller 05f77f85f4 bluetooth: Kill skb_frags_no(), unused.
Furthermore, it twiddles with the details of SKB list handling
directly, which we're trying to eliminate.

Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-08 16:16:56 -07:00
Marcel Holtmann 611b30f74b Bluetooth: Add native RFKILL soft-switch support for all devices
With the re-write of the RFKILL subsystem it is now possible to easily
integrate RFKILL soft-switch support into the Bluetooth subsystem. All
Bluetooth devices will now get automatically RFKILL support.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-06-08 14:50:01 +02:00
Marcel Holtmann b4324b5dc5 Bluetooth: Remove pointless endian conversion helpers
The Bluetooth source uses some endian conversion helpers, that in the end
translate to kernel standard routines. So remove this obfuscation since it
is fully pointless.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-06-08 14:50:01 +02:00
Marcel Holtmann 47ec1dcd69 Bluetooth: Add basic constants for L2CAP ERTM support and use them
This adds the basic constants required to add support for L2CAP Enhanced
Retransmission feature.

Based on a patch from Nathan Holstein <nathan@lampreynetworks.com>

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-06-08 14:50:00 +02:00
Gustavo F. Padovan 589d274648 Bluetooth: Use macro for L2CAP hint mask on receiving config request
Using the L2CAP_CONF_HINT macro is easier to understand than using a
hardcoded 0x80 value.

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-06-08 14:50:00 +02:00
Gustavo F. Padovan 8db4dc46dc Bluetooth: Use macros for L2CAP channel identifiers
Use macros instead of hardcoded numbers to make the L2CAP source code
more readable.

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-06-08 14:49:59 +02:00
Marcel Holtmann a67e899cf3 Bluetooth: Fix issue with sysfs handling for connections
Due to a semantic changes in flush_workqueue() the current approach of
synchronizing the sysfs handling for connections doesn't work anymore. The
whole approach is actually fully broken and based on assumptions that are
no longer valid.

With the introduction of Simple Pairing support, the creation of low-level
ACL links got changed. This change invalidates the reason why in the past
two independent work queues have been used for adding/removing sysfs
devices. The adding of the actual sysfs device is now postponed until the
host controller successfully assigns an unique handle to that link. So
the real synchronization happens inside the controller and not the host.

The only left-over problem is that some internals of the sysfs device
handling are not initialized ahead of time. This leaves potential access
to invalid data and can cause various NULL pointer dereferences. To fix
this a new function makes sure that all sysfs details are initialized
when an connection attempt is made. The actual sysfs device is only
registered when the connection has been successfully established. To
avoid a race condition with the registration, the check if a device is
registered has been moved into the removal work.

As an extra protection two flush_work() calls are left in place to
make sure a previous add/del work has been completed first.

Based on a report by Marc Pignat <marc.pignat@hevs.ch>

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Tested-by: Roger Quadros <ext-roger.quadros@nokia.com>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
2009-05-04 14:29:02 -07:00
Marcel Holtmann 052b30b0a8 Bluetooth: Add different pairing timeout for Legacy Pairing
The Bluetooth stack uses a reference counting for all established ACL
links and if no user (L2CAP connection) is present, the link will be
terminated to save power. The problem part is the dedicated pairing
when using Legacy Pairing (Bluetooth 2.0 and before). At that point
no user is present and pairing attempts will be disconnected within
10 seconds or less. In previous kernel version this was not a problem
since the disconnect timeout wasn't triggered on incoming connections
for the first time. However this caused issues with broken host stacks
that kept the connections around after dedicated pairing. When the
support for Simple Pairing got added, the link establishment procedure
needed to be changed and now causes issues when using Legacy Pairing

When using Simple Pairing it is possible to do a proper reference
counting of ACL link users. With Legacy Pairing this is not possible
since the specification is unclear in some areas and too many broken
Bluetooth devices have already been deployed. So instead of trying to
deal with all the broken devices, a special pairing timeout will be
introduced that increases the timeout to 60 seconds when pairing is
triggered.

If a broken devices now puts the stack into an unforeseen state, the
worst that happens is the disconnect timeout triggers after 120 seconds
instead of 4 seconds. This allows successful pairings with legacy and
broken devices now.

Based on a report by Johan Hedberg <johan.hedberg@nokia.com>

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-04-28 09:31:38 -07:00
Roger Quadros f3784d834c Bluetooth: Ensure that HCI sysfs add/del is preempt safe
Use a different work_struct variables for add_conn() and del_conn() and
use single work queue instead of two for adding and deleting connections.

It eliminates the following error on a preemptible kernel:

[  204.358032] Unable to handle kernel NULL pointer dereference at virtual address 0000000c
[  204.370697] pgd = c0004000
[  204.373443] [0000000c] *pgd=00000000
[  204.378601] Internal error: Oops: 17 [#1] PREEMPT
[  204.383361] Modules linked in: vfat fat rfcomm sco l2cap sd_mod scsi_mod iphb pvr2d drm omaplfb ps
[  204.438537] CPU: 0    Not tainted  (2.6.28-maemo2 #1)
[  204.443664] PC is at klist_put+0x2c/0xb4
[  204.447601] LR is at klist_put+0x18/0xb4
[  204.451568] pc : [<c0270f08>]    lr : [<c0270ef4>]    psr: a0000113
[  204.451568] sp : cf1b3f10  ip : cf1b3f10  fp : cf1b3f2c
[  204.463104] r10: 00000000  r9 : 00000000  r8 : bf08029c
[  204.468353] r7 : c7869200  r6 : cfbe2690  r5 : c78692c8  r4 : 00000001
[  204.474945] r3 : 00000001  r2 : cf1b2000  r1 : 00000001  r0 : 00000000
[  204.481506] Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM Segment kernel
[  204.488861] Control: 10c5387d  Table: 887fc018  DAC: 00000017
[  204.494628] Process btdelconn (pid: 515, stack limit = 0xcf1b22e0)

Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-04-28 09:31:38 -07:00
Marcel Holtmann 2950f21acb Bluetooth: Ask upper layers for HCI disconnect reason
Some of the qualification tests demand that in case of failures in L2CAP
the HCI disconnect should indicate a reason why L2CAP fails. This is a
bluntly layer violation since multiple L2CAP connections could be using
the same ACL and thus forcing a disconnect reason is not a good idea.

To comply with the Bluetooth test specification, the disconnect reason
is now stored in the L2CAP connection structure and every time a new
L2CAP channel is added it will set back to its default. So only in the
case where the L2CAP channel with the disconnect reason is really the
last one, it will propagated to the HCI layer.

The HCI layer has been extended with a disconnect indication that allows
it to ask upper layers for a disconnect reason. The upper layer must not
support this callback and in that case it will nicely default to the
existing behavior. If an upper layer like L2CAP can provide a disconnect
reason that one will be used to disconnect the ACL or SCO link.

No modification to the ACL disconnect timeout have been made. So in case
of Linux to Linux connection the initiator will disconnect the ACL link
before the acceptor side can signal the specific disconnect reason. That
is perfectly fine since Linux doesn't make use of this value anyway. The
L2CAP layer has a perfect valid error code for rejecting connection due
to a security violation. It is unclear why the Bluetooth specification
insists on having specific HCI disconnect reason.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-02-27 06:14:43 +01:00
Marcel Holtmann f29972de8e Bluetooth: Add CID field to L2CAP socket address structure
In preparation for L2CAP fixed channel support, the CID value of a
L2CAP connection needs to be accessible via the socket interface. The
CID is the connection identifier and exists as source and destination
value. So extend the L2CAP socket address structure with this field and
change getsockname() and getpeername() to fill it in.

The bind() and connect() functions have been modified to handle L2CAP
socket address structures of variable sizes. This makes them future
proof if additional fields need to be added.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-02-27 06:14:42 +01:00
Marcel Holtmann e1027a7c69 Bluetooth: Request L2CAP fixed channel list if available
If the extended features mask indicates support for fixed channels,
request the list of available fixed channels. This also enables the
fixed channel features bit so remote implementations can request
information about it. Currently only the signal channel will be
listed.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-02-27 06:14:42 +01:00
Marcel Holtmann 435fef20ac Bluetooth: Don't enforce authentication for L2CAP PSM 1 and 3
The recommendation for the L2CAP PSM 1 (SDP) is to not use any kind
of authentication or encryption. So don't trigger authentication
for incoming and outgoing SDP connections.

For L2CAP PSM 3 (RFCOMM) there is no clear requirement, but with
Bluetooth 2.1 the initiator is required to enable authentication
and encryption first and this gets enforced. So there is no need
to trigger an additional authentication step. The RFCOMM service
security will make sure that a secure enough link key is present.

When the encryption gets enabled after the SDP connection setup,
then switch the security level from SDP to low security.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-02-27 06:14:41 +01:00
Marcel Holtmann 6a8d3010b3 Bluetooth: Fix double L2CAP connection request
If the remote L2CAP server uses authentication pending stage and
encryption is enabled it can happen that a L2CAP connection request is
sent twice due to a race condition in the connection state machine.

When the remote side indicates any kind of connection pending, then
track this state and skip sending of L2CAP commands for this period.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-02-27 06:14:41 +01:00
Marcel Holtmann 984947dc64 Bluetooth: Fix race condition with L2CAP information request
When two L2CAP connections are requested quickly after the ACL link has
been established there exists a window for a race condition where a
connection request is sent before the information response has been
received. Any connection request should only be sent after an exchange
of the extended features mask has been finished.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-02-27 06:14:41 +01:00
Marcel Holtmann 0684e5f9fb Bluetooth: Use general bonding whenever possible
When receiving incoming connection to specific services, always use
general bonding. This ensures that the link key gets stored and can be
used for further authentications.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-02-27 06:14:40 +01:00
Marcel Holtmann efc7688b55 Bluetooth: Add SCO fallback for eSCO connection attempts
When attempting to setup eSCO connections it can happen that some link
manager implementations fail to properly negotiate the eSCO parameters
and thus fail the eSCO setup. Normally the link manager is responsible
for the negotiation of the parameters and actually fallback to SCO if
no agreement can be reached. In cases where the link manager is just too
stupid, then at least try to establish a SCO link if eSCO fails.

For the Bluetooth devices with EDR support this includes handling packet
types of EDR basebands. This is particular tricky since for the EDR the
logic of enabling/disabling one specific packet type is turned around.
This fix contains an extra bitmask to disable eSCO EDR packet when
trying to fallback to a SCO connection.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-02-27 06:14:37 +01:00
Marcel Holtmann 8c84b83076 Bluetooth: Pause RFCOMM TX when encryption drops
A role switch with devices following the Bluetooth pre-2.1 standards
or without Encryption Pause and Resume support is not possible if
encryption is enabled. Most newer headsets require the role switch,
but also require that the connection is encrypted.

For connections with a high security mode setting, the link will be
immediately dropped. When the connection uses medium security mode
setting, then a grace period is introduced where the TX is halted and
the remote device gets a change to re-enable encryption after the
role switch. If not re-enabled the link will be dropped.

Based on initial work by Ville Tervo <ville.tervo@nokia.com>

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-02-27 06:14:33 +01:00