After association, STA will go through eapol handshake with WPS
enabled AP. It's observed that WPS handshake fails with some 11n
AP. The reason for the failure is that the eapol packet is sent
via 11n frame aggregation.
The eapol packet should be sent directly without 11n aggregation.
This patch fixes the problem by adding WPS session control while
dequeuing Tx packets for transmission.
Cc: "3.4.y" <stable@vger.kernel.org>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we check the sequence number of last packet received
against start_win. If a sequence hole is detected, start_win is
updated to next sequence number.
Since the rx sequence number is initialized to 0, a corner case
exists when BA setup happens immediately after association. As
0 is a valid sequence number, start_win gets increased to 1
incorrectly. This causes the first packet with sequence number 0
being dropped.
Initialize rx sequence number as 0xffff and skip adjusting
start_win if the sequence number remains 0xffff. The sequence
number will be updated once the first packet is received.
Cc: "3.0.y, 3.1.y, 3.2.y, 3.3.y, 3.4.y" <stable@vger.kernel.org>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This changes oprofile_perf.c to use the per-cpu framework.
Using the per-cpu framework should avoid error like the following:
arch/arm/oprofile/../../../drivers/oprofile/oprofile_perf.c:28:28: error: variably modified 'perf_events' at file scope
Reported-by: William Cohen <wcohen@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Currently DMA channels are allocated and they remain allocated
even if there is no active data transfer. Added channel_release()
whenever there is no pending request.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If CONFIG_USB_GADGET_DEBUG_FILES is enabled, lpc32xx_udc breaks
compilation because of a missing include file.
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There were mistakes in writing to few twl
registers. There was interchange in the
parameters being passed to twl6030_writeb().
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Two minor fixes in emc2103 and applesmc drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=kDRE
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Two minor fixes in emc2103 and applesmc drivers."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (emc2103) Fix use of an uninitilized variable in error case
hwmon: (applesmc) Limit key length in warning messages
The OProfile perf backend uses a static array to keep track of the
perf events on the system. When compiling with CONFIG_CPUMASK_OFFSTACK=y
&& SMP, nr_cpumask_bits is not a compile-time constant and the build
will fail with:
oprofile_perf.c:28: error: variably modified 'perf_events' at file scope
This patch uses NR_CPUs instead of nr_cpumask_bits for the array
initialisation. If this causes space problems in the future, we can
always move to dynamic allocation for the events array.
Cc: Matt Fleming <matt@console-pimps.org>
Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org> # v2.6.37+
Signed-off-by: Robert Richter <robert.richter@amd.com>
drivers/media/video/pms.c uses kzalloc() and kfree() so it should
include <linux/slab.h> to fix build errors and a warning.
drivers/media/video/pms.c:1047:2: error: implicit declaration of function 'kzalloc'
drivers/media/video/pms.c:1047:6: warning: assignment makes pointer from integer without a cast
drivers/media/video/pms.c:1116:2: error: implicit declaration of function 'kfree'
Found in mmotm but applies to mainline.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need to initialize this to false, because the is_rb callback only
ever sets it to true.
Noticed while reading through the code.
Cc: stable@vger.kernel.org
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull slave-dmaengine fixes from Vinod Koul:
"A few fixes in pl330 and imx-sdma drivers."
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
DMA: PL330: Fix racy mutex unlock
DMA: PL330: Add missing static storage class specifier
dma: imx-sdma: buf_tail should be initialize in prepare function
dmaengine: pl330: dont complete descriptor for cyclic dma
drivers/media/video/pms.c uses kzalloc() and kfree() so it should
include <linux/slab.h> to fix build errors and a warning.
drivers/media/video/pms.c:1047:2: error: implicit declaration of function 'kzalloc'
drivers/media/video/pms.c:1047:6: warning: assignment makes pointer from integer without a cast
drivers/media/video/pms.c:1116:2: error: implicit declaration of function 'kfree'
Found in mmotm but applies to mainline.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are a number of small fixes for the drivers/staging tree, as well as iio
and pstore drivers (which came from the staging tree in the 3.5-rc1 merge).
All of these are tiny, but resolve issues that people have been reporting.
There's also a documentation update to reflect what the iio drivers really are
doing, which is good to get straightened out.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/iNeAACgkQMUfUDdst+ynNVwCdHCj6smC2JUbvN34gACNrpsYY
WggAoJzQn9mQhwq0pa/ZTpaUOvCFZ39L
=hDkC
-----END PGP SIGNATURE-----
Merge tag 'staging-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree fixes from Greg Kroah-Hartman:
"Here are a number of small fixes for the drivers/staging tree, as well
as iio and pstore drivers (which came from the staging tree in the
3.5-rc1 merge). All of these are tiny, but resolve issues that people
have been reporting.
There's also a documentation update to reflect what the iio drivers
really are doing, which is good to get straightened out.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8712u: Add new USB IDs
staging: gdm72xx: Release netlink socket properly
iio: drop wrong reference from Kconfig
pstore/inode: Make pstore_fill_super() static
pstore/ram: Should zap persistent zone on unlink
pstore/ram_core: Factor persistent_ram_zap() out of post_init()
pstore/ram_core: Do not reset restored zone's position and size
pstore/ram: Should update old dmesg buffer before reading
staging:iio:ad7298: Fix linker error due to missing IIO kfifo buffer
Revert "staging: usbip: bugfix for stack corruption on 64-bit architectures"
staging: usbip: bugfix for stack corruption on 64-bit architectures
staging/comedi: fix build for USB not enabled
staging: omapdrm: fix crash when freeing bad fb
staging:iio:ad7606: Re-add missing scale attribute
iio: Fix potential use after free
staging:iio: remove num_interrupt_lines from documentation
iio: documentation: Add out_altvoltage and friends
Here are some fixes for 3.5-rc4 that resolve the kmsg problems that
people have reported showing up after the printk and kmsg changes went
into 3.5-rc1. There are also a smattering of other tiny fixes for the
extcon and hyper-v drivers that people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/iNQcACgkQMUfUDdst+yklTQCfZCXFlhA43bZo/8Joqd2pLIIW
2uoAoMze0SlfJeN6Qu7yY0P+qV/f/pc3
=UNFY
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and printk fixes from Greg Kroah-Hartman:
"Here are some fixes for 3.5-rc4 that resolve the kmsg problems that
people have reported showing up after the printk and kmsg changes went
into 3.5-rc1. There are also a smattering of other tiny fixes for the
extcon and hyper-v drivers that people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
extcon: max8997: Add missing kfree for info->edev in max8997_muic_remove()
extcon: Set platform drvdata in gpio_extcon_probe() and fix irq leak
extcon: Fix wrong index in max8997_extcon_cable[]
kmsg - kmsg_dump() fix CONFIG_PRINTK=n compilation
printk: return -EINVAL if the message len is bigger than the buf size
printk: use mutex lock to stop syslog_seq from going wild
kmsg - kmsg_dump() use iterator to receive log buffer content
vme: change maintainer e-mail address
Extcon: Don't try to create duplicate link names
driver core: fixup reversed deferred probe order
printk: Fix alignment of buf causing crash on ARM EABI
Tools: hv: verify origin of netlink connector message
Here are some drivers/misc bugfixes (really just drivers/misc/mei/
fixes) for a few problems that have been reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/iNGgACgkQMUfUDdst+ymmPwCeLxWcEx3UE0pyhwssITArJZz3
WFIAmgPHM66lgXioLxR3swCib9FFo+Xp
=hIWT
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull misc tree updates from Greg Kroah-Hartman:
"Here are some drivers/misc bugfixes (really just drivers/misc/mei/
fixes) for a few problems that have been reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'char-misc-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
misc: mei: set WDIOF_ALARMONLY on mei watchdog
misc: mei: Disable MSI when IRQ registration fails
misc: mei: fix stalled read
misc: mei: unregister misc device in pci_remove function
misc: mei: set IRQF_ONESHOT for msi request_threaded_irq
Here are 3 patches resolving a boot regression (the mop500 fix), a build
warning fix, and a kernel-doc fix. All tiny, but should go into the
final 3.5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/iNosACgkQMUfUDdst+ykedgCeLhpFrq5dI19tbhEmCroFs4sx
f+4An29dz2bGkjeViDNkmaBC7msPzLNc
=EBge
-----END PGP SIGNATURE-----
Merge tag 'tty-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fixes from Greg Kroah-Hartman:
"Here are 3 patches resolving a boot regression (the mop500 fix), a
build warning fix, and a kernel-doc fix. All tiny, but should go into
the final 3.5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial/amba-pl011: move custom pin control to driver
serial: fix serial_txx9.c build warning/typo
serial: fix kernel-doc warnings in 8250.c
* emailed from Andrew Morton <akpm@linux-foundation.org>: (21 patches)
mm/memblock: fix overlapping allocation when doubling reserved array
c/r: prctl: Move PR_GET_TID_ADDRESS to a proper place
pidns: find_new_reaper() can no longer switch to init_pid_ns.child_reaper
pidns: guarantee that the pidns init will be the last pidns process reaped
fault-inject: avoid call to random32() if fault injection is disabled
Viresh has moved
get_maintainer: Fix --help warning
mm/memory.c: fix kernel-doc warnings
mm: fix kernel-doc warnings
mm: correctly synchronize rss-counters at exit/exec
mm, thp: print useful information when mmap_sem is unlocked in zap_pmd_range
h8300: use the declarations provided by <asm/sections.h>
h8300: fix use of extinct _sbss and _ebss
xtensa: use the declarations provided by <asm/sections.h>
xtensa: use "test -e" instead of bashism "test -a"
xtensa: replace xtensa-specific _f{data,text} by _s{data,text}
memcg: fix use_hierarchy css_is_ancestor oops regression
mm, oom: fix and cleanup oom score calculations
nilfs2: ensure proper cache clearing for gc-inodes
thp: avoid atomic64_read in pmd_read_atomic for 32bit PAE
...
viresh.kumar@st.com email-id doesn't exist anymore as I have left the
company. Replace ST's id with viresh.linux@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'
Signed-off-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use the correct union for getting the tiling info
- Properly init the PIPE_CONFIG field for SI
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
After the change "mac80211: remove spurious BSSID change flag",
BSS_CHANGED_BSSID will not be passed on association or IBSS
status changes. So it could be better to program bssid on ASSOC
or IBSS change notification. Not doing so, is affecting the
packet transmission.
Cc: stable@vger.kernel.org [3.4+]
Reported-by: Michael Leun <lkml20120218@newton.leun.net>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When debugging is disabled, the event log functions aren't
functional in the way that the debugfs file expects. This
leads to the debugfs access crashing. Since the event log
functions aren't functional then, remove the debugfs file
when CONFIG_IWLWIFI_DEBUG is not set.
Cc: stable@kernel.org
Reported-by: Lekensteyn <lekensteyn@gmail.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ath9k: Fix softlockup in AR9485" with commit id
64bc1239c7 fixed the reported
issue, yet its better to avoid the possible infinite loop
in ar9003_get_pll_sqsum_dvc by having a timeout as suggested
by ath9k maintainers.
http://www.spinics.net/lists/linux-wireless/msg92126.html.
Based on my testing PLL's locking measurement is done in
~200us (2 iterations).
Cc: stable@vger.kernel.org
Cc: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes two memory leaks in the SPI initialization code.
Patch based on old maemo patch by:
Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Always report beacon loss to the stack, not only when in powersave
state. This is because there's possibility that the driver disables
PSM before it handles old BSS_LOSE_EVENT, so beacon loss has to be
reported.
Patch based on old maemo patch by:
Janne Ylalehto <janne.ylalehto@nokia.com>
Juuso Oikarinen <juuso.oikarinen@nokia.com>
Luciano Coelho <luciano.coelho@nokia.com>
Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cast MSB part of current TSF to u64 to prevent loss of most
significant bits. MSB should also be shifted by 32.
Patch based on old maemo patch by:
Yuri Kululin <ext-yuri.kululin@nokia.com>
Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull ARM fixes from Russell King:
"This includes three MMCI changes - one to fix up the wrong version of
the DT support patch which was merged, and two to make deferred
probing work. It also includes a fix to the OMAP SPI driver which is
causing a boot time warning.
The remainder are very minor ARM fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
SPI: fix over-eager devm_xxx() conversion
ARM: 7427/1: mmc: mmci: Defer probe() in case of yet uninitialized GPIOs
ARM: 7426/1: mmc: mmci: Remove wrong error handling of gpio 0
ARM: 7425/1: extable: ensure fixup entries are 4-byte aligned
ARM: 7421/1: bpf_jit: BPF_S_ANC_ALU_XOR_X support
ARM: 7423/1: kprobes: run t32_simulate_ldr_literal() without insn slot
ARM: 7422/1: mmc: mmci: Allocate platform memory during Device Tree boot
- Fixed a 2-line compile error for MXS
- A pure documentation fix for Nomadik
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJP4PWNAAoJEEEQszewGV1zE2UQAKRMoeJw97o9NFuHICg3+oMA
SExUxD9H9Ey5nWtFsjqVkZKkEksdFlDwkdsXoXxsDVZlVNBFM/oxRe3fGiqgEIjN
/fks/xfFBo7xQPoJw05z8Z/dYKDgchhor5Q7oRWReYMnNhuHccjWdhD0Z7dFG27Q
Up8purFH3v3qidxXy3jrLG03b+s/wDHTzsGBP2sIJVhUvMkVcoi3AUgjoWE/Qj68
Ljklf1f5mSzY6YKU4kkpSaickoD8FxxkbTk4qNarFk4RLTxQeFOyqjVN0lFfUjF1
sUvfnlgeFYy3N3Vp5keI1iBRBuRYBR002WI3T6uorHyM78ssbks5md3BxA/IDff+
QTdPUCKNAfPqnqmnVBsvtTSb9MrdreBEiSw6j31fzgeN+MipYc2h0BErJPynMKGP
QWWZrm0q+ux6bf/bsdfpBl7q0RD0d45qihYI7azQq4vV/QfXpFsPxDdFY+edIau4
TVb3c7xang5cMK7aq+HZ9tBV8v4WvcGg+OSPOitaXyIk4kHmO3E+eYGQ9GsSFxcK
Jd25v88tXrrip4//fEb6RCRxf1oHeZ8onR8Ex8FsxMh0cMumhXi+VmKEel0UJKux
42Ti/Pl6CX/FtiU5hwzn6ojwntR9yaQHz7bInzkUgeP8r1fLa96IN2ndoLDv0SEh
gvFcBaAbZV7WlZV8gLkD
=zNxH
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull two pinctrl fixes from Linus Walleij:
- Fixed a 2-line compile error for MXS
- A pure documentation fix for Nomadik
* tag 'pinctrl-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl/nomadik: document Alt-C glitch
pinctrl: mxs: Use kfree to fix build error
get_voltage_sel() should return selector rather than voltage.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes a memory leak that was introduced in the 3.4 kernel. The
leak occurred when FCoE was enabled and traffic was passed over the FCoE
rings reserved for FCoE. The memory leak was due to us not populating the
compound page information on the order 1 pages needed for FCoE.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix Kconfig file to make sure that PTP and IGB/IXGBE are both either
in-kernel or modules, not mixed. Having the build status mixed causes
compile errors.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i210/i211 device has only 16 RAR address filters like 82575, instead of
32 like i350. This patch removes the entries for i210/i211 in the
get_invariants function which was setting them for 32. This ensures that
they will get the default value which is the correct one.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change || check to the intended && when checking the QP type in a
received connection request against the listening endpoint.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
One small bug fix, plus a rename of all the ST Ericsson regulators in
the device tree since all the device trees had been written with
different names and some infelicities in the test proceedures meant that
the device tree code had apparently never actually been run against the
upstream device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=NS0T
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"One small bug fix, plus a rename of all the ST Ericsson regulators in
the device tree since all the device trees had been written with
different names and some infelicities in the test proceedures meant
that the device tree code had apparently never actually been run
against the upstream device tree."
* tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Change db8500-prcmu match names to reflect Device Tree
regulator: Change ab8500 match names to reflect Device Tree
regulator: Fix the s5m8767a problem of the division by null
add_virtual_intf() needs to return an ERR_PTR(), instead of NULL,
on errors, otherwise cfg80211 will crash.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"qual" used to be declared on the stack, but then in 998a5a7d6a ("airo:
reduce stack memory footprint") we made it dynamically allocated.
Unfortunately the memcpy() here was missed and it's still copying stack
memory instead of the data that we want. In other words, "&qual" should
be "qual".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When running heavy traffic we stop the tx queue if the pending
packet count reaches certain threshold. Later, the tx queue should
be woken up as soon as the packet count falls below the threshold.
Current code wakes TX queue up on STA interface only. Removing the
check for STA interface will allow both STA and AP interfaces to
resume transmit when tx_pending count becomes low.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
spin_unlock_bh(&txq->lock) already disables softirqs so we don't want
to do it here. Fixes smatch warnings:
drivers/net/wireless/ath/ath5k/base.c:1048 ath5k_drain_tx_buffs() error: double lock 'bottom_half:'
drivers/net/wireless/ath/ath5k/base.c:1056 ath5k_drain_tx_buffs() error: double unlock 'bottom_half:'
Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After setup_frame_info has been called, only info->control.rates is still
valid, other control fields have been overwritten by the ath_frame_info
data. Move the access to info->control.vif for checking short preamble
to setup_frame_info before it gets overwritten.
This regression was introduced in commit d47a61aa
"ath9k: Fix multi-VIF BSS handling"
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Thomas Hühn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: stable@vger.kernel.org [3.4]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate pointer variable for a rate series is used in a loop before it is
initialized. This went unnoticed because it was used earlier for the RTS/CTS
rate. This bug can lead to the wrong PHY type being passed to the
duration calculation function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On a freescale imx6q platform, a hardware phy chip KSZ9021 is
recognized as a KS8001 chip by the current driver like this:
eth0: Freescale FEC PHY driver [Micrel KS8001 or KS8721]
KSZ9021 has phy_id 0x00221610, while KSZ8001 has phy_id
0x0022161a, the current phy_id_mask (0x00fffff0/0x00ffff10) can't
distinguish them. So change phy_id_mask to resolve this problem.
Although the micrel datasheet says that the 4 LSB of phyid2 register
contains the chip revision number and the current driver is designed
to follow this rule, in reality the chip implementation doesn't follow
it.
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vendor-specific events shall be processed in driver and not sent
to bluetooth stack where they screw up HCI command countings.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
extcon_dev_unregister(info->edev) doest not free info->edev, we need to call
kfree(info->edev) here.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing platform_set_drvdata() in gpio_extcon_probe(), otherwise calling
platform_get_drvdata in gpio_extcon_remove() returns NULL.
Also add missing free_irq call in gpio_extcon_remove().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the index of "Dock-desk" and "Dock-card" are the same.
Thus the latter one overrides the first one.
Then we have problem when calling extcon_find_cable_index() because
edev->supported_cable[7] only matches "Dock-card".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a compiler breakage introduced by commit 8173090acb33:
drivers/media/video/pms.c: In function ‘pms_probe’:
drivers/media/video/pms.c:1047:2: error: implicit declaration of function ‘kzalloc’ [-Werror=implicit-function-declaration]
drivers/media/video/pms.c:1116:2: error: implicit declaration of function ‘kfree’ [-Werror=implicit-function-declaration]
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed the size of the V4L2_CID_COLORFX control cluster.
Prior to this fix V4L2_CID_ROTATE was also icluded in
the cluster preventing application from enabling rotation.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes the following error:
ERROR: open brace '{' following enum go on the same line
+enum MFC_SHM_OFS
+{
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed s_ctrl function when setting the following controls:
- V4L2_CID_MPEG_VIDEO_DECODER_MPEG4_DEBLOCK_FILTER
- V4L2_CID_MPEG_MFC51_VIDEO_DECODER_H264_DISPLAY_DELAY
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Image size for MFC encoder should have size between
8x4 and 1920x1080 with even width and height.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch corrects definition of H264 level control and
changes bare numbers to enums in two other cases.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mem2mem_testdev allows multiple instances to be opened in parallel.
Source and destination queue data are being shared between all
instances, which can lead to kernel oops due to race conditions (most
likely to happen inside device_run()).
Attached patch fixes mentioned problem by storing queue data per device
context.
Signed-off-by: Tomasz Moń <desowin@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed the code copying timecode/timestamp to corresponding
frames between OUTPUT and CAPTURE.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull EDAC fixes from Mauro Carvalho Chehab.
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
edac: Do alignment logic properly in edac_align_ptr()
mpc85xx_edac: fix error: too few arguments to function 'edac_mc_alloc'
edac: fix the error about memory type detection on SandyBridge
edac: avoid mce decoding crash after edac driver unloaded
Fix an incorrect modulation type bitmask. This allows QAM256 also to be
correctly reported.
Signed-off-by: Janne Huttunen <jahuttun@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull a crypto fix from Herbert Xu:
"This push fixes another bug in the atmel-rng that made it produce
completely useless output."
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: atmel-rng - fix data valid check
Fix:
emc2103.c: In function set_pwm_enable:
emc2103.c:463:12: warning: conf_reg may be used uninitialized in this function
by checking the return value from read_u8_from_i2c(). This fixes a real problem,
as conf_reg is really uninitialized if read_u8_from_i2c returns an error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Key lookups may call read_smc() with a fixed-length key string,
and if the lookup fails, trailing stack content may appear in the
kernel log. Fixed with this patch.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This simply shows a little warning if the board does not have remote
control support. This should make it easier for users to see if they
have misconfigured their system or if the driver simply does not have
rc-support for their card (yet).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Cinergy HTC Stick HD uses the same remote control as the TerraTec
Cinergy XS products. Thus the same keymap could be re-used.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit d509835e32. That commit
breaks support for the generic pass-through mode in the driver for formats,
not natively supported by it. Besides due to a merge conflict it also breaks
driver compilation:
drivers/media/video/mx2_camera.c: In function 'mx2_camera_set_bus_param':
drivers/media/video/mx2_camera.c:937: error: 'pixfmt' undeclared (first use in this function)
drivers/media/video/mx2_camera.c:937: error: (Each undeclared identifier is reported only once
drivers/media/video/mx2_camera.c:937: error: for each function it appears in.)
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1a77b127ae (OMAP : SPI : use devm_* functions) converted the SPI
device controller state to use devm_kzalloc(). Unfortunately, this
is used against an unbound struct device, which results in the
following when the device is bound to its driver:
------------[ cut here ]------------
WARNING: at /home/rmk/git/linux-rmk/drivers/base/dd.c:257 driver_probe_device+0x78/0x21c()
Modules linked in:
Backtrace:
[<c0017d0c>] (dump_backtrace+0x0/0x10c) from [<c033e208>] (dump_stack+0x18/0x1c) r7:00000000 r6:c01ff28c r5:c040050c r4:00000101
[<c033e1f0>] (dump_stack+0x0/0x1c) from [<c00337ec>] (warn_slowpath_common+0x58/0x70)
[<c0033794>] (warn_slowpath_common+0x0/0x70) from [<c0033828>] (warn_slowpath_null+0x24/0x2c)
[<c0033804>] (warn_slowpath_null+0x0/0x2c) from [<c01ff28c>] (driver_probe_device+0x78/0x21c)
[<c01ff214>] (driver_probe_device+0x0/0x21c) from [<c01ff49c>] (__driver_attach+0x6c/0x90)
[<c01ff430>] (__driver_attach+0x0/0x90) from [<c01fda70>] (bus_for_each_dev+0x58/0x98)
[<c01fda18>] (bus_for_each_dev+0x0/0x98) from [<c01ff0f4>] (driver_attach+0x20/0x28)
[<c01ff0d4>] (driver_attach+0x0/0x28) from [<c01fe2f4>] (bus_add_driver+0xb4/0x230)
[<c01fe240>] (bus_add_driver+0x0/0x230) from [<c01ffb24>] (driver_register+0xac/0x138)
[<c01ffa78>] (driver_register+0x0/0x138) from [<c0215d4c>] (spi_register_driver+0x4c/0x60)
[<c0215d00>] (spi_register_driver+0x0/0x60) from [<c045414c>] (ks8851_init+0x14/0x1c)
[<c0454138>] (ks8851_init+0x0/0x1c) from [<c0008770>] (do_one_initcall+0x9c/0x164)
[<c00086d4>] (do_one_initcall+0x0/0x164) from [<c0436410>] (kernel_init+0x128/0x210)
[<c04362e8>] (kernel_init+0x0/0x210) from [<c0038754>] (do_exit+0x0/0x72c)
---[ end trace 4dcda79f5e89dd84 ]---
ks8851 spi1.0: message enable is 0
ks8851 spi1.0: eth0: revision 0, MAC 08:00:28:01:4d:c6, IRQ 194, has EEPROM
Fix this by partially reverting the original commit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are four link statuses of a bonding slave, the procfs
code shows a wrong status when using downdelay/updelay:
(slave->link == BOND_LINK_UP) ? "up" : "down"
It doesn't respect the rest two statuses. This patch fixes it.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As seen on smsc75xx, driver_info->description being longer than 32
characters messes up 'ethtool -i' output.
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increasing the hardware statistics structure to accomodate statistics for skyhawk.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify IOCTL error message to print subsystem also.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum size of packet that can be handled by controller including ethernet
header is 65535. Reducing gso_max_size accordingly.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a potential hole when configuring the cycle counter used to
generate the nanosecond time clock. This clock is based off of the SYSTIME
registers along with the TIMINCA registers. The TIMINCA register determines
the increment to be added to the SYSTIME registers every DMA clock tick. This
register needs to be reconfigured whenever the link-speed changes. However,
the value calculated stays the same when link is down and when link is up.
Misconfiguration can occur if the link status changes due to a reset, which
causes the TIMINCA register to be reset. This reset puts the device in an
unstable state where the SYSTIME registers stop incrementing and the PTP
protocol does not function.
The solution is to double check the TIMINCA value and always reset the value
if the register is zero. This prevents a misconfiguration bug that halts the
PHC.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the GPIOs used by the MMCI driver are not registered yet when the driver is
probe()d, they can't be used. This happens if the mmci driver is probed before
the respective GPIO controller (e.g. on the LPC32xx EA3250 board, the PCA9532
GPIO controller would be initialized via DT after mmci). Therefore, we defer
mmci in this case.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Zero is a valid GPIO and shouldn't be handled as an error return code from
of_get_named_gpio(). It was a leftover from old code before getting
pdata->gpio_*() was modified.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to the datasheet:
The LDO_CTRL registers are used to set the output voltage of LDO1 and LDO2.
LDO_CTRL[7] and LDO_CTRL[3] are reserved and should always be written to 0.
Thus the mask for TPS65023_LDO_1 and TPS65023_LDO_2 should be 0x07 and 0x70
respectively.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This documentation comment existed in an earlier patch set for
GPIO consolidation, so I'm saving it for maintainability of the
code.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 0bf7481 (pinctrl: pinctrl-mxs: Take care of frees if the kzalloc fails)
introduced the following build error:
drivers/pinctrl/pinctrl-mxs.c:140:3: error: implicit declaration of function 'free'
Use kfree function instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 'name' field in 'struct of_regulator_match' expects to match with
its corresponding regulator device node in the Device Tree. This patch
renames each of the regulators in the db8500-prcum regulator driver so
this is true.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The 'name' field in 'struct of_regulator_match' expects to match with
its corresponding regulator device node in the Device Tree. This patch
renames each of the regulators in the ab8500 regulator driver so this
is true.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If ramp_delay is 0, delay value can be divided by zero.
This patch can fix the problem.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Atom CPUs don't have a register to retrieve TjMax. Detection so far was
incomplete. Use the X86 model ID to improve it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Document the Atom series D2000 and N2000 (Cedar Trail) as being supported.
List and set TjMax for those series.
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "R, Durgadoss" <durgadoss.r@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Document the new Atom series (Tunnel Creek and Medfield) as being
supported, and list TjMax for the Atom E600 series.
Also enable the Atom tjmax heuristic for these Atom CPU models.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "R, Durgadoss" <durgadoss.r@intel.com>
Pull drm fixes from Dave Airlie:
"Radeon is most of the work, one regression, one BUG fix in the new
prime code, some fixes to init code to make streamout not lock up the
hardware, and just some code to enable users to test HDMI audio on
later hw (its off by default).
Intel adds edp edid caching for some strange Dell Vostros that black
screen on startup if keep reading their EDID, and a fix for a DP
regression.
Otherwise fix for via/sis and one to stop udl binding to multiple
non-video usb."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: cache the EDID for eDP panels
Revert "drm/i915/dp: Use auxch precharge value of 5 everywhere"
drm/i915: eDP aux needs vdd
drm/i915: don't enumerate HDMID if an eDP panel is already active on the port
drm/radeon: add support for STRMOUT_BASE_UPDATE on 7xx
drm/radeon: add some additional 6xx/7xx/EG register init
drm/radeon: enable HDMI on DCE5 (AKA NI excluding Aruba)
drm sis: initialize object_idr
drm via: initialize object_idr
drm/radeon/prime: reserve/unreserve around pin
drm/radeon: fix regression in dynpm due to multi-ring rework
vga_switcheroo.h: fix pci_dev warning
drm/udl: only bind to the video devices on the hub.
For some reason one of the dev_err invocations is using a wrong
device so fix that.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: stable@vger.kernel.org
When I2C is not responding it's usually due to a previous
unexpected reset during I2C operation. We release it by
powering down and up the SFP+ module.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- two fixes for s3c-fb by Jingoo Han
(including a fix for a potential division by zero)
- a couple of randconfig fixes by Arnd Bergmann
- a cleanup for bfin_adv7393fb by Emil Goode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=0Zkc
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-for-3.5-1' of git://github.com/schandinat/linux-2.6
Pull fbdev fixes from Florian Tobias Schandinat:
- two fixes for s3c-fb by Jingoo Han (including a fix for a potential
division by zero)
- a couple of randconfig fixes by Arnd Bergmann
- a cleanup for bfin_adv7393fb by Emil Goode
* tag 'fbdev-fixes-for-3.5-1' of git://github.com/schandinat/linux-2.6:
video: s3c-fb: fix possible division by zero in s3c_fb_calc_pixclk
video: s3c-fb: clear SHADOWCON register when clearing hardware window registers
drivers/tosa: driver needs I2C and SPI to compile
drivers/savagefb: use mdelay instead of udelay
video/console: automatically select a font
video/ili9320: do not mark exported functions __devexit
drivers/video: use correct __devexit_p annotation
video: bfin_adv7393fb: Convert to kstrtouint_from_user
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: cache the EDID for eDP panels
Revert "drm/i915/dp: Use auxch precharge value of 5 everywhere"
drm/i915: eDP aux needs vdd
drm/i915: don't enumerate HDMID if an eDP panel is already active on the port
They aren't going anywhere, and probing on DDC can cause the panel to
blank briefly, so read them up front and cache them for later queries.
v2: fix potential NULL derefs in intel_dp_get_edid_modes and
intel_dp_get_edid (Jani)
copy full EDID length, including extension blocks (Takashi)
free EDID on teardown (Takashi)
v3: malloc a new EDID buffer that's big enough for the memcpy (Chris)
v4: change handling of NULL EDIDs, just preserve the NULL behavior
across detects and mode list fetches rather than trying to re-fetch
the EDID (Chris)
v5: be glad that Chris is around to remind me to hit C-x C-s before
committing.
References: https://bugs.freedesktop.org/show_bug.cgi?id=46856
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 092945e11c.
This commit prevents a DP screen from properly training the link.
Oddly enough it works, once the machine has been warm-booted with an
older kernel.
According to DP docs this _should_ have been the right precharge time.
Also, the commit that originally introduces this was just general snb
DP enabling and didn't mention any specific reason for this special
value. Whatever, trust the reporter that this makes things worse and
let's just revert it.
v2: Less spelling fail.
Cc: Adam Jackson <ajax@redhat.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reported-by: "Wouter M. Koolen" <W.M.Koolen-Wijkstra@cwi.nl>
Buglink: https://lkml.org/lkml/2012/6/14/301
Cc: stable@vger.kernel.org (only for 3.4)
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The new oui probe has been missing these.
This issue has been introduce in
commit 0d19832853
Author: Adam Jackson <ajax@redhat.com>
Date: Mon May 14 16:05:47 2012 -0400
drm/i915/dp: Probe branch/sink OUIs
v2: Do the eDP vdd dance of simply not probing the OUI on eDP panels
as suggested by Chris Wilson.
v3: Fix up the error path fail - I suck.
Cc: Adam Jackson <ajax@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50808
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Bugreport: http://permalink.gmane.org/gmane.comp.video.dri.devel/69695
Tested-by: Yang Guang <guang.a.yang@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This prevents the HDMI detect functions from poking at an eDP
connected panel, which can lead to trouble.
[danvet: Note that we have some other reports of DP vs. HDMI fighting,
but the general case is a much bigger fish to fry.]
References: https://bugs.freedesktop.org/show_bug.cgi?id=42278
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Required for streamout. Bump drm minor.
Marek v2: fix pkt->count check
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- SMX_SAR_CTL0 needs to be programmed correctly to prevent
problems with memory exports in certain cases.
- VC_ENHANCE needs to be initialized on 6xx/7xx.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
After recent changes HDMI code is ready to be enabled on DCE5. This
patch just changes conditions to execute already present code on DCE5.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Christian König <christian.koenig@amd.com>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The filed object_idr of struct drm_sis_private was introduced with
commit http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commitdiff;h=6de8a748881f1cd9d795454da2b6db616d5ca3d7 .
The idr_init(&dev->object_name_idr) is called instead of
idr_init(&dev_priv->object_idr) by mistake, leaving object_idr
uninitialized. Correct this.
This patch was not tested because of lack of hardware.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The field obejct_idr of struct drm_via_private was introduced with the
commit http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commitdiff;h=77ee8f3825054f23b17e9c8f728f061defd86cdc .
In that patch idr_init(&dev->object_name_idr) was called instead of
idr_init(&dev_priv->object_idr) by mistake, leaving the dev_priv->object_idr
uninitialized. To be more exact, the object_idr buffer is filled with zeros
because of kzalloc(), but the dev_priv->object_idr.lock spinlock can cause
system freeze at lib/idr.c:move_to_free_list() when spin_lock_irqsave()
is called on this spinlock.
The patch was tested on Clevo D4J, model D410J laptop, on the following
hardware, without AGP kernel module loaded:
# lspci -s 01:00.0 -n
01:00.0 0300: 1106:3108 (rev 01)
# lspci -s 01:00.0 -v
01:00.0 VGA compatible controller: VIA Technologies, Inc. K8M800/K8N800/K8N800A [S3 UniChrome Pro] (rev 01) (prog-if 00 [VGA controller])
Subsystem: CLEVO/KAPOK Computer Device 4702
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
Memory at f0000000 (32-bit, prefetchable) [size=64M]
Memory at d1000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at <unassigned> [disabled]
Capabilities: [60] Power Management version 2
Capabilities: [70] AGP version 3.0
Signed-off-by: Márton Németh <nm127@freemail.hu>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
I finally got to test this code a bit more and hit the ttm
no reserved assert, so add the reservations around the pinning.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Not all asics have all rings, so make sure the ring is ready
before attempting to check it in the dynpm work handler.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=43367
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a couple of minor fixes, one for a preempt warning in the mpt2sas
driver and one is a config failure with the new sd async domain.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJP2fuGAAoJEDeqqVYsXL0Md88IAMw1nLZkg39TzEM4tAkkCa4C
o3e3xcmUdO1lqswmgUDaD95Z0H9MUBxwHWQGiAQ7fheuyXXyGOLINkBTx7wOGksk
JpsjEHNhVwW2rxFwZDLYxvtBjRy9E6wJPeuBQxQdU2gGVzjmk2bAV6mJnf+/wDkH
uqJKnrmVNU7x5drw1wP2z0i3zm8UZVlB+eW3J5ReZzfQlpBYWmFcwxrSTp8Q03ko
rx+rMNYlQO+5Cp0/UZxdIlTw4TTaU+F6bXC8jPzZ2zj0mUWtBxiF6rYZQlebNM5n
/byCuivfM9OMeWaiwk5ERIQ/1iOUF4L5apCNUIG2PFtS7RY4349luWpBoeYkaVY=
=eNSh
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a couple of minor fixes, one for a preempt warning in the
mpt2sas driver and one is a config failure with the new sd async
domain."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] Fix sd_probe_domain config problem
[SCSI] mpt2sas: Fix unsafe using smp_processor_id() in preemptible
- When booting as PVHVM we would try to use PV console - but would not validate
the parameters causing us to crash during restore b/c we re-use the wrong event
channel.
- When booting on machines with SR-IOV PCI bridge we didn't check for the bridge
and tried to use it.
- Under AMD machines would advertise the APERFMPERF resulting in needless amount
of MSRs from the guest.
- A global value (xen_released_pages) was not subtracted at bootup when pages
were added back in. This resulted in the balloon worker having the wrong
account of how many pages were truly released.
- Fix dead-lock when xen-blkfront is run in the same domain as xen-blkback.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJP2kcmAAoJEFjIrFwIi8fJXLcH/0a2m6KMcyjc4WaCHspAEFDL
9B055QUFDEOlH55wE2QeED/8D+0HUbTYnQBycH126XLKzLfRv1fsrKFKDSA/SWW2
Mh8N316UrY5Wc3KMdxXdCXJCDqDs7VhARTv6JdlUqUlH9oLRYE6CMRO8MujT0iwd
r+uEnNuW0udMFt8x9SnJW7pEaq7u2N5koEGdWEzZhfoumDaCRxm5OKAKXZ0DZlEZ
/BPjTW/N+Pf4u+bJZY+wQq41y4zGMqu7TDo/hOpuGZxeqtVnCE9trBbuGLnp4K+W
n4TfZZs9Y1kovSMj6qTeB0aP0F77tqHyXPb1oPKxm2kWfqT2dFtIRpuLtXYSC+o=
=cQl2
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.5-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull five Xen bug-fixes from Konrad Rzeszutek Wilk:
- When booting as PVHVM we would try to use PV console - but would not validate
the parameters causing us to crash during restore b/c we re-use the wrong event
channel.
- When booting on machines with SR-IOV PCI bridge we didn't check for the bridge
and tried to use it.
- Under AMD machines would advertise the APERFMPERF resulting in needless amount
of MSRs from the guest.
- A global value (xen_released_pages) was not subtracted at bootup when pages
were added back in. This resulted in the balloon worker having the wrong
account of how many pages were truly released.
- Fix dead-lock when xen-blkfront is run in the same domain as xen-blkback.
* tag 'stable/for-linus-3.5-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: mark local pages as FOREIGN in the m2p_override
xen/setup: filter APERFMPERF cpuid feature out
xen/balloon: Subtract from xen_released_pages the count that is populated.
xen/pci: Check for PCI bridge before using it.
xen/events: Add WARN_ON when quick lookup found invalid type.
xen/hvc: Check HVM_PARAM_CONSOLE_[EVTCHN|PFN] for correctness.
xen/hvc: Fix error cases around HVM_PARAM_CONSOLE_PFN
xen/hvc: Collapse error logic.
Here are a bunch of tiny fixes for the USB core and drivers for 3.5-rc3
A bunch of gadget fixes, and new device ids, as well as some fixes for a number
of different regressions that have been reported recently. We also fixed some
PCI host controllers to resolve a long-standing bug with a whole class of host
controllers that have been plaguing people for a number of kernel releases,
preventing their systems from suspending properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/byIEACgkQMUfUDdst+ykLBwCgiAi/cS4ObblcBEbnBvosPgsA
PqEAoJLMAwhcozeEOWLhb++45Vs+UjKv
=HAWc
-----END PGP SIGNATURE-----
Merge tag 'usb-3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a bunch of tiny fixes for the USB core and drivers for
3.5-rc3
A bunch of gadget fixes, and new device ids, as well as some fixes for
a number of different regressions that have been reported recently.
We also fixed some PCI host controllers to resolve a long-standing bug
with a whole class of host controllers that have been plaguing people
for a number of kernel releases, preventing their systems from
suspending properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (41 commits)
USB: fix gathering of interface associations
usb: ehci-sh: fix illegal phy_init() running when platform_data is NULL
usb: cdc-acm: fix devices not unthrottled on open
Fix OMAP EHCI suspend/resume failure (i693)
USB: ohci-hub: Mark ohci_finish_controller_resume() as __maybe_unused
usb: use usb_serial_put in usb_serial_probe errors
USB: EHCI: Fix build warning in xilinx ehci driver
USB: fix PS3 EHCI systems
xHCI: Increase the timeout for controller save/restore state operation
xhci: Don't free endpoints in xhci_mem_cleanup()
xhci: Fix invalid loop check in xhci_free_tt_info()
xhci: Fix error path return value.
USB: Checking the wrong variable in usb_disable_lpm()
usb-storage: Add 090c:1000 to unusal-devs
USB: serial-generic: use a single set of device IDs
USB: serial: Enforce USB driver and USB serial driver match
USB: add NO_D3_DURING_SLEEP flag and revert 151b612847
USB: option: add more YUGA device ids
USB: mos7840: Fix compilation of usb serial driver
USB: option: fix memory leak
...
Pull IDE fixes from David S. Miller:
1) Two fixes to icside, one for a build failure and another for a
warning. From Christian Dietrich.
2) Fix a bit operation that did erroneous masking, from Julia Lawall.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
drivers/ide/ide-cs.c: adjust suspicious bit operation
ide: icside.c: fix printk format string compile warning
ide: icside.c: Fix compile with CONFIG_BLK_DEV_IDEDMA_ICS=n
Pull target updates from Nicholas Bellinger:
"This series contains post merge qla_target.c / tcm_qla2xxx bugfixes
from the past weeks, including the patch to allow target-core to use
an optional session shutdown callback to help address an active I/O
shutdown bug in tcm_qla2xxx code (Joern).
Also included is a target regression bugfix releated to explict ALUA
target port group CDB emulation that is CC'ed to stable (Roland)."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
qla2xxx: Remove version.h header file inclusion
tcm_qla2xxx: Handle malformed wwn strings properly
tcm_qla2xxx: tcm_qla2xxx_handle_tmr() can be static
qla2xxx: Don't leak commands we give up on in qlt_do_work()
qla2xxx: Don't crash if we can't find cmd for failed CTIO
tcm_qla2xxx: Don't insert nacls without sessions into the btree
target: Return error to initiator if SET TARGET PORT GROUPS emulation fails
tcm_qla2xxx: Clear session s_id + loop_id earlier during shutdown
tcm_qla2xxx: Convert to TFO->put_session() usage
target: Add TFO->put_session() caller for HW fabric session shutdown
The adapter->npars[] array has QLCNIC_MAX_PCI_FUNC elements. We
allocate it that way a few lines earlier in the function. So this test
is off by one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a off by one error in the minimal number of BD in
bnx2x_start_xmit() and bnx2x_tx_int() before stopping/resuming tx queue.
A full size GSO packet, with data included in skb->head really needs
(MAX_SKB_FRAGS + 4) BDs, because of bnx2x_tx_split()
This error triggers if BQL is disabled and heavy TCP transmit traffic
occurs.
bnx2x_tx_split() definitely can be called, remove a wrong comment.
Reported-by: Tomas Hruby <thruby@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Yaniv Rosner <yanivr@broadcom.com>
Cc: Merav Sicron <meravs@broadcom.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Robert Evans <evansr@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(CAN_CTRLMODE_LISTENONLY & CAN_CTRLMODE_LOOPBACK) is (0x02 & 0x01) which
is zero so the condition is never true. The intent here was to test
that both flags were set.
Cc: <stable@kernel.org> # 2.6.39+
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide an iterator to receive the log buffer content, and convert all
kmsg_dump() users to it.
The structured data in the kmsg buffer now contains binary data, which
should no longer be copied verbatim to the kmsg_dump() users.
The iterator should provide reliable access to the buffer data, and also
supports proper log line-aware chunking of data while iterating.
Signed-off-by: Kay Sievers <kay@vrfy.org>
Tested-by: Tony Luck <tony.luck@intel.com>
Reported-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Tested-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two new devices for this driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of ep_dequeue , if dequeued request was submitted for dma
transfer, then endpoint is stopped. Once endpoint is stooped, callback
for the dequeued request must be called.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When matching devices against an OF device ID table, the first string of
the compatible property that is listed in the table should match,
regardless of its position in the table.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The documentation lives in drivers/staging/iio/Documentation, but
according to Jonathan it's obsolete and needs fixing.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't create a link from the device to the compatibility switch class
since we already create a link from the device to to the extcon class
object and we try to use the same name for both links. This causes a loud
complaint from sysfs on boot.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TEAC's UD-H01 (and probably other devices) have a gap in the interface
number allocation of their descriptors:
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 220
bNumInterfaces 3
[...]
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
[...]
Interface Association:
bLength 8
bDescriptorType 11
bFirstInterface 2
bInterfaceCount 2
bFunctionClass 1 Audio
bFunctionSubClass 0
bFunctionProtocol 32
iFunction 4
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
[...]
Once a configuration is selected, usb_set_configuration() walks the
known interfaces of a given configuration and calls find_iad() on
each of them to set the interface association pointer the interface
is included in.
The problem here is that the loop variable is taken for the interface
number in the comparison logic that gathers the association. Which is
fine as long as the descriptors are sane.
In the case above, however, the logic gets out of sync and the
interface association fields of all interfaces beyond the interface
number gap are wrong.
Fix this by passing the interface's bInterfaceNumber to find_iad()
instead.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: bEN <ml_all@circa.be>
Reported-by: Ivan Perrone <ivanperrone@hotmail.com>
Tested-by: ivan perrone <ivanperrone@hotmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the platform_data is not set, pdata will be uninitialized value.
Since the driver has the following code, if the condition is true when
the pdata is uninitialized value, the driver may jump to the illegal
phy_init().
if (pdata && pdata->phy_init)
pdata->phy_init();
This patch also fixes the following warning:
CC drivers/usb/host/ehci-hcd.o
drivers/usb/host/ehci-sh.c: In function ‘ehci_hcd_sh_probe’:
drivers/usb/host/ehci-sh.c:104: warning: ‘pdata’ may be used uninitialized in this function
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently CDC-ACM devices stay throttled when their TTY is closed while
throttled, stalling further communication attempts after the next open.
Unthrottling during open/activate got lost starting with kernel
3.0.0 and this patch reintroduces it.
Signed-off-by: Otto Meta <otto.patches@sister-shadow.de>
Cc: stable <stable@vger.kernel.org>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev->sgid_tbl[] array is allocated in ocrdma_alloc_resources().
It has OCRDMA_MAX_SGID elements so the test here is off by one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When booting with Device Tree enabled, platform specific information
is gathered by parsing the DT binary. Platform data is subsequently
populated with the result. The memory required for this is not
automatically allocated during Device Tree boot, so we'll do it here
instead.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- section markup fixes
- clk_prepare() fix to conform to the clk API
- memory leaks
- incorrect debug messages
- bad errorpaths
- typos
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=F/II
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
- section markup fixes
- clk_prepare() fix to conform to the clk API
- memory leaks
- incorrect debug messages
- bad errorpaths
- typos
* tag 'pinctrl-fixes-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: pinctrl-mxs: set platform driver data to NULL at errpath and at unregister
pinctrl: pinctrl-mxs: Take care of frees if the kzalloc fails
pinctrl: pinctrl-imx: fix incorrect debug message of maps
pinctrl: pinctrl-imx: free if of_get_parent fails to get the parent node
pinctrl: pinctrl-imx: free allocated pinctrl_map structure only once and use kernel facilities for IMX_PMX_DUMP
pinctrl: nomadik: fix up typo
pinctrl: nomadik: add clk_prepare() call
pinctrl: fix a minor harmless typo
pinctrl: sirf: mark of_device_id match table as __devinitconst
- Fix a regression of USB-audio PCM assignment since 3.4
- A few VGA-switcheroo-related fixes for proper HDMI audio enablement
- Fixed the missing initializations of HD-audio verbs, which may have
resulted in various breakage
- Some driver-specific ASoC updates
- A few fixes for the dynamic PCM code
- The addition of pinctrl support for the i.MX audmux which didn't make it
into -rc1 due to cross tree dependency issues
- A few minor fixes in compress API codes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=Hrh7
-----END PGP SIGNATURE-----
Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
- Fix a regression of USB-audio PCM assignment since 3.4
- A few VGA-switcheroo-related fixes for proper HDMI audio enablement
- Fixed the missing initializations of HD-audio verbs, which may have
resulted in various breakage
- Some driver-specific ASoC updates
- A few fixes for the dynamic PCM code
- The addition of pinctrl support for the i.MX audmux which didn't make
it into -rc1 due to cross tree dependency issues
- A few minor fixes in compress API codes
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Don't forget to call init verbs added by fixup list
ALSA: HDA: Pin fixup for Zotac Z68 motherboard
ALSA: compress_core: cleanup pointers on stop
ALSA: compress_core: don't wake up on pause
ALSA: hda - Fix detection of Creative SoundCore3D controllers
vga_switcheroo: Enable/disable audio clients at the right time
ALSA: hda - HDMI Audio init all connectors when VGA-switcheroo is off
vga_switcheroo: Fix error without CONFIG_VGA_SWITCHEROO
ALSA: hda - Fix uninitialized HDMI controllers with VGA-switcheroo
vga_switcheroo: Add a helper function to get the client state
ALSA: usb-audio: Fix substream assignments
ASoC: tegra: add MODULE_DEVICE_TABLE to tegra30_ahub
ASoC: wm2000: Always use a 4s timeout for the firmware
ASoC: dapm: Fix input list to use source widgets
ASoC: dpcm: Fix dpcm_get_be() to check that DAI is BE
ASoC: wm8994: Apply volume updates with clocks enabled
ASoC: wm8994: Ensure all AIFnCLK events are run from the _late variants
ASoC: imx-audmux: add pinctrl support
ASoC: dapm: Fix connected widget capture path query.
Pull networking fixes from David S. Miller:
This has the fix for the wireless issues I ran into the other week as
well as:
1) Fix CAN c_can driver transmit handling resulting in BUG check
triggers, from AnilKumar Ch.
2) Fix packet drop monitor sleeping in atomic context, from Eric
Dumazet.
3) Fix mv643xx_eth driver build regression, from Andrew Lunn.
4) Inetpeer freeing needs an RCU grace period in order to avoid races
during tree invalidation. From Eric Dumazet.
5) Fix endianness bugs in xt_HMARK netfilter module, from Hans
Schillstrom.
6) Add proper module refcounting to l2tp_eth to avoid crash on module
unload, from Eric Dumazet.
7) Fix truncation of neighbour entry dumps due to logic errors in
neigh_dump_info() and friends, from Eric Dumazet.
8) The conversion of fib6_age() to dst_neigh_lookup() accidently
reversed the logic of a flags test, fix from Thomas Graf.
9) Fix checksum configuration in newer sky2 chips, from Stephen
Hemminger.
10) Revert BQL support in NIU driver, doesn't work.
11) l2tp_ip_sendmsg() illegally uses a route without a proper reference.
From Eric Dumazet.
12) be2net driver references an SKB after it's potentially been freed,
also from Eric Dumazet.
13) Fix RCU stalls in dummy net driver init. Also from Eric Dumazet.
14) lpc_eth has several bugs in it's transmit engine leading to packet
leaks and improper queue wakes, from Eric Dumazet.
15) Apply short DMA workaround to more tg3 chips, from Matt Carlson.
16) Add tilegx network driver.
17) Bonding queue mapping for a packet can get corrupted, fix from Eric
Dumazet.
18) Fix bug in netpoll_send_udp() SKB management that can leave garbage
in the payload in certain situations. From Eric Dumazet.
19) bnx2x driver interprets chip RX checksum offload incorrectly in
encapsulation situations. Fix from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
bnx2x: fix checksum validation
netpoll: fix netpoll_send_udp() bugs
bonding: Fix corrupted queue_mapping
bonding:record primary when modify it via sysfs
tilegx network driver: initial support
tg3: Apply short DMA frag workaround to 5906
net: stmmac: Fix clock en-/disable calls
lpc_eth: fix tx completion
lpc_eth: add missing ndo_change_mtu()
dummy: fix rcu_sched self-detected stalls
net: Reorder initialization in ip_route_output to fix gcc warning
virtio-net: fix a race on 32bit arches
r8169: avoid NAPI scheduling delay.
net: Make linux/tcp.h C++ friendly (trivial)
netdev: fix drivers/net/phy/ kernel-doc warnings
net/core: fix kernel-doc warnings
be2net: fix a race in be_xmit()
l2tp: fix a race in l2tp_ip_sendmsg()
mac80211: add back channel change flag
NFC: Fix possible NULL ptr deref when getting the name of a socket
...
pl330_update() stores a pointer to the thrd->req that finished, which
contains a pointer to the corresponding pl330_req. This is done with
the pl330_lock held. Then, it iterates through the req_done list,
calling the callback for each of the requests that are done. The
problem is that the driver releases the lock before calling the
callback for each of the callbacks. pl330_submit_req() running in
another processor can then acquire the lock and insert another request
in one of the thrd->req that hasn't been processed yet, replacing the
pointer to pl330_req there. When the callback returns in
pl330_update() and the next rqdone is popped from the list, it
dereferences the pl330_req pointer to the just scheduled pl330_req,
instead of the one that has finished, calling pl330 with the wrong r.
This patch fixes this by storing the pointer to pl330_req directly in
the list.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Its observed with some PHY, the 60Mhz clock gets
cut too soon for OMAP EHCI, leaving OMAP-EHCI in a bad state.
So on starting port suspend, make sure the 60Mhz clock to EHCI
is kept alive using an internal clock, so that EHCi can cleanly
transition its hw state machine on a port suspend.
Its not proven if this is the issue hit on USB3333,
but the symptoms look very similar.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Volodymyr Mieshkov <x0182794@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ohci_finish_controller_resume() is intended to be used in platform specific
drivers ohci-*.c, included from ohci-hcd.c. Some of them don't actually use
ohci_finish_controller_resume(), so mark it as __maybe_unused.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The use of kfree(serial) in error cases of usb_serial_probe
was invalid - usb_serial structure allocated in create_serial()
gets reference of usb_device that needs to be put, so we need
to use usb_serial_put() instead of simple kfree().
Signed-off-by: Jan Safrata <jan.nikitenko@gmail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the following warning:
In file included from drivers/usb/host/ehci-hcd.c:1246:0:
drivers/usb/host/ehci-xilinx-of.c:293:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/usb/host/ehci-xilinx-of.c:293:2: warning: (near initialization for 'ehci_hcd_xilinx_of_driver.shutdown') [enabled by default]
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit aaa0ef289a "PS3 EHCI QH
read work-around", Terratec Grabby (em28xx) stopped working with AMD
Geode LX 800 (USB controller AMD CS5536). Since this is a PS3 only
fix, the following patch adds a conditional block around it.
Signed-off-by: Ricardo Martins <rasm@fe.up.pt>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
Here's five bug fixes for 3.5. They fix some memory leaks in the
bandwidth calculation code, fix a couple bugs in the USB3 Link PM
patchset, and make system suspend and resume work on platforms with the
AsMedia ASM1042 xHCI host controller.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=oodF
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2012-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
xhci: Bug fixes for 3.5
Hi Greg,
Here's five bug fixes for 3.5. They fix some memory leaks in the
bandwidth calculation code, fix a couple bugs in the USB3 Link PM
patchset, and make system suspend and resume work on platforms with the
AsMedia ASM1042 xHCI host controller.
Sarah Sharp
When system software decides to power down the xHC with the intent of
resuming operation at a later time, it will ask xHC to save the internal
state and restore it when resume to correctly recover from a power event.
Two bits are used to enable this operation: Save State and Restore State.
xHCI spec 4.23.2 says software should "Set the Controller Save/Restore
State flag in the USBCMD register and wait for the Save/Restore State
Status flag in the USBSTS register to transition to '0'". However, it does
not define how long software should wait for the SSS/RSS bit to transition
to 0.
Currently the timeout is set to 1ms. There is bug report
(https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1002697)
indicates that the timeout is too short for ASMedia ASM1042 host controller
to save/restore the state successfully. Increase the timeout to 10ms helps to
resolve the issue.
This patch should be backported to stable kernels as old as 2.6.37, that
contain the commit 5535b1d5f8 "USB: xHCI:
PCI power management implementation"
Signed-off-by: Andiry Xu <andiry.xu@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: stable@vger.kernel.org
This patch fixes a few issues introduced in the recent fix
[f8a9e72d: USB: fix resource leak in xhci power loss path]
- The endpoints listed in bw table are just links and each entry is an
array member of dev->eps[]. But the commit above adds a kfree() call
to these instances, and thus it results in memory corruption.
- It clears only the first entry of rh_bw[], but there can be multiple
ports.
- It'd be safer to clear the list_head of ep as well, not only
removing from the list, as it's checked in
xhci_discover_or_reset_device().
This patch should be backported to kernels as old as 3.2, that contain
the commit 839c817ce6 "xhci: Store
information about roothubs and TTs."
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: Oliver Neukum <oneukum@suse.de>
Cc: <stable@vger.kernel.org>
xhci_free_tt_info() may access the invalid memory when it removes the
last entry but the list is not empty. Then tt_next reaches to the
list head but it still tries to check the tt_info of that entry.
This patch fixes the bug and cleans up the messy code by rewriting
with a simple list_for_each_entry_safe().
This patch should be backported to kernels as old as 3.2, that contain
the commit 839c817ce6 "xhci: Store
information about roothubs and TTs."
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: Oliver Neukum <oneukum@suse.de>
Cc: <stable@vger.kernel.org>
This patch fixes an issue discovered by Dan Carpenter:
The patch 3b3db026414b: "xhci: Add infrastructure for host-specific
LPM policies." from May 9, 2012, leads to the following warning:
drivers/usb/host/xhci.c:3909 xhci_get_timeout_no_hub_lpm()
warn: signedness bug returning '-22'
3906 default:
3907 dev_warn(&udev->dev, "%s: Can't get timeout for non-U1 or U2 state.\n",
3908 __func__);
3909 return -EINVAL;
^^^^^^^^^^^^^^
This should be a u16 like USB3_LPM_DISABLED or something.
3910 }
3911
3912 if (sel <= max_sel_pel && pel <= max_sel_pel)
3913 return USB3_LPM_DEVICE_INITIATED;
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
We check "u1_params" instead of checking "u2_params".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This device gives a bogus answer to get_capacity(16):
[ 8628.278614] scsi 8:0:0:0: Direct-Access USB 2.0 USB Flash Drive 1100 PQ: 0 ANSI: 4
[ 8628.279452] sd 8:0:0:0: Attached scsi generic sg4 type 0
[ 8628.280338] sd 8:0:0:0: [sdd] 35747322042253313 512-byte logical blocks: (18.3 EB/15.8 EiB)
So set the quirk flag to avoid using get_capacity(16) with it:
[11731.386014] usb-storage 2-1.6:1.0: Quirks match for vid 090c pid 1000: 80000
[11731.386075] scsi9 : usb-storage 2-1.6:1.0
[11731.386172] usbcore: registered new interface driver usb-storage
[11731.386175] USB Mass Storage support registered.
[11732.387394] scsi 9:0:0:0: Direct-Access USB 2.0 USB Flash Drive 1100 PQ: 0 ANSI: 4
[11732.388462] sd 9:0:0:0: Attached scsi generic sg3 type 0
[11732.389432] sd 9:0:0:0: [sdc] 7975296 512-byte logical blocks: (4.08 GB/3.80 GiB)
Which makes the capacity look a lot more sane :)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Simon Raffeiner <sturmflut@lieberbiber.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bnx2x driver incorrectly sets ip_summed to CHECKSUM_UNNECESSARY on
encapsulated segments. TCP stack happily accepts frames with bad
checksums, if they are inside a GRE or IPIP encapsulation.
Our understanding is that if no IP or L4 csum validation was done by the
hardware, we should leave ip_summed as is (CHECKSUM_NONE), since
hardware doesn't provide CHECKSUM_COMPLETE support in its cqe.
Then, if IP/L4 checksumming was done by the hardware, set
CHECKSUM_UNNECESSARY if no error was flagged.
Patch based on findings and analysis from Robert Evans
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Yaniv Rosner <yanivr@broadcom.com>
Cc: Merav Sicron <meravs@broadcom.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Robert Evans <evansr@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mei watchdog doesn't reboot the system it only produces event
therefore mark it as WDIOF_ALARMONLY.
This patch depends on:
commit 2bbeed016d
Author: Alan Cox <alan@linux.intel.com>
watchdog: Add a flag to indicate the watchdog doesn't reboot things
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since MSI is enabled right before that, we should disable it when
registration fails.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb-serial-generic driver uses different device IDs for its USB
matching and its serial matching. This can lead to problems: The
driver can end up getting bound to a USB interface without being
allowed to bind to the corresponding serial port.
This patch (as1557) fixes the problem by using the same device ID
table (the one that can be altered by the "vendor=" and "product="
module parameters) for both purposes. The unused table is removed.
Now the driver will bind only to the intended devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to make sure that the USB serial driver we find
matches the USB driver whose probe we are currently
executing. Otherwise we will end up with USB serial
devices bound to the correct serial driver but wrong
USB driver.
An example of such cross-probing, where the usbserial_generic
USB driver has found the sierra serial driver:
May 29 18:26:15 nemi kernel: [ 4442.559246] usbserial_generic 4-4:1.0: Sierra USB modem converter detected
May 29 18:26:20 nemi kernel: [ 4447.556747] usbserial_generic 4-4:1.2: Sierra USB modem converter detected
May 29 18:26:25 nemi kernel: [ 4452.557288] usbserial_generic 4-4:1.3: Sierra USB modem converter detected
sysfs view of the same problem:
bjorn@nemi:~$ ls -l /sys/bus/usb/drivers/sierra/
total 0
--w------- 1 root root 4096 May 29 18:23 bind
lrwxrwxrwx 1 root root 0 May 29 18:23 module -> ../../../../module/usbserial
--w------- 1 root root 4096 May 29 18:23 uevent
--w------- 1 root root 4096 May 29 18:23 unbind
bjorn@nemi:~$ ls -l /sys/bus/usb-serial/drivers/sierra/
total 0
--w------- 1 root root 4096 May 29 18:23 bind
lrwxrwxrwx 1 root root 0 May 29 18:23 module -> ../../../../module/sierra
-rw-r--r-- 1 root root 4096 May 29 18:23 new_id
lrwxrwxrwx 1 root root 0 May 29 18:32 ttyUSB0 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.0/ttyUSB0
lrwxrwxrwx 1 root root 0 May 29 18:32 ttyUSB1 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.2/ttyUSB1
lrwxrwxrwx 1 root root 0 May 29 18:32 ttyUSB2 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.3/ttyUSB2
--w------- 1 root root 4096 May 29 18:23 uevent
--w------- 1 root root 4096 May 29 18:23 unbind
bjorn@nemi:~$ ls -l /sys/bus/usb/drivers/usbserial_generic/
total 0
lrwxrwxrwx 1 root root 0 May 29 18:33 4-4:1.0 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.0
lrwxrwxrwx 1 root root 0 May 29 18:33 4-4:1.2 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.2
lrwxrwxrwx 1 root root 0 May 29 18:33 4-4:1.3 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.3
--w------- 1 root root 4096 May 29 18:33 bind
lrwxrwxrwx 1 root root 0 May 29 18:33 module -> ../../../../module/usbserial
--w------- 1 root root 4096 May 29 18:22 uevent
--w------- 1 root root 4096 May 29 18:33 unbind
bjorn@nemi:~$ ls -l /sys/bus/usb-serial/drivers/generic/
total 0
--w------- 1 root root 4096 May 29 18:33 bind
lrwxrwxrwx 1 root root 0 May 29 18:33 module -> ../../../../module/usbserial
-rw-r--r-- 1 root root 4096 May 29 18:33 new_id
--w------- 1 root root 4096 May 29 18:22 uevent
--w------- 1 root root 4096 May 29 18:33 unbind
So we end up with a mismatch between the USB driver and the
USB serial driver. The reason for the above is simple: The
USB driver probe will succeed if *any* registered serial
driver matches, and will use that serial driver for all
serial driver functions.
This makes ref counting go wrong. We count the USB driver
as used, but not the USB serial driver. This may result
in Oops'es as demonstrated by Johan Hovold <jhovold@gmail.com>:
[11811.646396] drivers/usb/serial/usb-serial.c: get_free_serial 1
[11811.646443] drivers/usb/serial/usb-serial.c: get_free_serial - minor base = 0
[11811.646460] drivers/usb/serial/usb-serial.c: usb_serial_probe - registering ttyUSB0
[11811.646766] usb 6-1: pl2303 converter now attached to ttyUSB0
[11812.264197] USB Serial deregistering driver FTDI USB Serial Device
[11812.264865] usbcore: deregistering interface driver ftdi_sio
[11812.282180] USB Serial deregistering driver pl2303
[11812.283141] pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
[11812.283272] usbcore: deregistering interface driver pl2303
[11812.301056] USB Serial deregistering driver generic
[11812.301186] usbcore: deregistering interface driver usbserial_generic
[11812.301259] drivers/usb/serial/usb-serial.c: usb_serial_disconnect
[11812.301823] BUG: unable to handle kernel paging request at f8e7438c
[11812.301845] IP: [<f8e38445>] usb_serial_disconnect+0xb5/0x100 [usbserial]
[11812.301871] *pde = 357ef067 *pte = 00000000
[11812.301957] Oops: 0000 [#1] PREEMPT SMP
[11812.301983] Modules linked in: usbserial(-) [last unloaded: pl2303]
[11812.302008]
[11812.302019] Pid: 1323, comm: modprobe Tainted: G W 3.4.0-rc7+ #101 Dell Inc. Vostro 1520/0T816J
[11812.302115] EIP: 0060:[<f8e38445>] EFLAGS: 00010246 CPU: 1
[11812.302130] EIP is at usb_serial_disconnect+0xb5/0x100 [usbserial]
[11812.302141] EAX: f508a180 EBX: f508a180 ECX: 00000000 EDX: f8e74300
[11812.302151] ESI: f5050800 EDI: 00000001 EBP: f5141e78 ESP: f5141e58
[11812.302160] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[11812.302170] CR0: 8005003b CR2: f8e7438c CR3: 34848000 CR4: 000007d0
[11812.302180] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[11812.302189] DR6: ffff0ff0 DR7: 00000400
[11812.302199] Process modprobe (pid: 1323, ti=f5140000 task=f61e2bc0 task.ti=f5140000)
[11812.302209] Stack:
[11812.302216] f8e3be0f f8e3b29c f8e3ae00 00000000 f513641c f5136400 f513641c f507a540
[11812.302325] f5141e98 c133d2c1 00000000 00000000 f509c400 f513641c f507a590 f5136450
[11812.302372] f5141ea8 c12f0344 f513641c f507a590 f5141ebc c12f0c67 00000000 f507a590
[11812.302419] Call Trace:
[11812.302439] [<c133d2c1>] usb_unbind_interface+0x51/0x190
[11812.302456] [<c12f0344>] __device_release_driver+0x64/0xb0
[11812.302469] [<c12f0c67>] driver_detach+0x97/0xa0
[11812.302483] [<c12f001c>] bus_remove_driver+0x6c/0xe0
[11812.302500] [<c145938d>] ? __mutex_unlock_slowpath+0xcd/0x140
[11812.302514] [<c12f0ff9>] driver_unregister+0x49/0x80
[11812.302528] [<c1457df6>] ? printk+0x1d/0x1f
[11812.302540] [<c133c50d>] usb_deregister+0x5d/0xb0
[11812.302557] [<f8e37c55>] ? usb_serial_deregister+0x45/0x50 [usbserial]
[11812.302575] [<f8e37c8d>] usb_serial_deregister_drivers+0x2d/0x40 [usbserial]
[11812.302593] [<f8e3a6e2>] usb_serial_generic_deregister+0x12/0x20 [usbserial]
[11812.302611] [<f8e3acf0>] usb_serial_exit+0x8/0x32 [usbserial]
[11812.302716] [<c1080b48>] sys_delete_module+0x158/0x260
[11812.302730] [<c110594e>] ? mntput+0x1e/0x30
[11812.302746] [<c145c3c3>] ? sysenter_exit+0xf/0x18
[11812.302746] [<c107777c>] ? trace_hardirqs_on_caller+0xec/0x170
[11812.302746] [<c145c390>] sysenter_do_call+0x12/0x36
[11812.302746] Code: 24 02 00 00 e8 dd f3 20 c8 f6 86 74 02 00 00 02 74 b4 8d 86 4c 02 00 00 47 e8 78 55 4b c8 0f b6 43 0e 39 f8 7f a9 8b 53 04 89 d8 <ff> 92 8c 00 00 00 89 d8 e8 0e ff ff ff 8b 45 f0 c7 44 24 04 2f
[11812.302746] EIP: [<f8e38445>] usb_serial_disconnect+0xb5/0x100 [usbserial] SS:ESP 0068:f5141e58
[11812.302746] CR2: 00000000f8e7438c
Fix by only evaluating serial drivers pointing back to the
USB driver we are currently probing. This still allows two
or more drivers to match the same device, running their
serial driver probes to sort out which one to use.
Cc: stable@vger.kernel.org # 3.0, 3.2, 3.3, 3.4
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This bug caused severe connectivity issue in the LMS application
(LMS is described in Documentation/misc-devices/mei/mei.txt)
The bug was introduced in patch:
commit 1ccb7b6249
staging/mei: propagate error codes up in the write flow
The patch has reverted the return value logic of some fo function but
the conditional in _mei_irq_thread_read function was not swapped
making read always entering the error path
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the misc device is registered only in the pci probe function
it has to be also unregistered in the counterpart pci remove function
and not in the module exit function.
In case of probe failure the driver was oopsing in module exit function.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when the default irq quick handler is used then IRQF_ONESHOT must be set
otherwise the request fails and following error is displayed:
genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq ...
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If driver requests probe deferral,
it will be added to deferred_probe_pending_list
by driver_deferred_probe_add(), but, it used list_add().
Because of that, deferred probe will be run as reversed order.
This patch uses list_add_tail(), and solved this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.15 (GNU/Linux)
iEYEABECAAYFAk/YA2QACgkQGkmNcg7/o7iquwCg1dTXMRl6iC+/nGrfBylFhbvQ
IjQAnj/+piJJlqdN8HDPnnXOvbcgZLNk
=hO8d
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: Kill off additional asm-generic wrappers.
sh: Setup CROSS_COMPILE at the top
sh: Fix up link time defsym warnings.
sh: use the new generic strnlen_user() function
sh: switch to generic strncpy_from_user().
sh: Kill off last dead UBC header
serial: sh-sci: Make probe fail for ports that exceed the maximum count
serial: sh-sci: Fix probe error paths
clocksource: sh_tmu: Use clockevents_config_and_register().
clocksource: sh_tmu: Convert timer lock to raw spinlock.
clocksource: sh_mtu2: Convert timer lock to raw spinlock.
clocksource: sh_cmt: Convert timer lock to raw spinlock.
bug.h: need linux/kernel.h for TAINT_WARN.
sh: convert to kbuild asm-generic support.
sh64: Fix up fallout from generic init_task conversion.
sh: arch/sh/kernel/process.c needs asm/fpu.h for unlazy_fpu().
Pull led fixes from Bryan Wu.
* 'fixes-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: Make LEDS_ASIC3 and LEDS_RENESAS_TPU depend on LEDS_CLASS=y
leds: fixed a coding style issue.
leds: don't disable blinking when writing the same value to delay_on or delay_off
This patch (as1558) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers. Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.
After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state. Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.
The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep. Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.
A similar patch has already been applied as commit
151b612847 (USB: EHCI: fix crash during
suspend on ASUS computers). The patch supersedes that one and reverts
it. There are two differences:
The old patch added the flag at the USB level; this patch
adds it at the PCI level.
The old patch applied to all chipsets with the same vendor,
subsystem vendor, and product IDs; this patch makes an
exception for a known-good system (based on DMI information).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dâniel Fraga <fragabr@gmail.com>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a regression introduced by 7eaceaccab ("block: remove per-queue
plugging"). In that patch, Jens removed the whole mm_unplug_device()
function, which used to be the trigger to make umem start to work.
We need to implement unplugging to make umem start to work, or I/O will
never be triggered.
Signed-off-by: Tao Guo <Tao.Guo@emc.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Shaohua Li <shli@kernel.org>
Cc: <stable@vger.kernel.org>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Without this, modules can't use this API, leading to build failures.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
steps to recreate:
load latest ath9k driver with AR9485
stop the network-manager and wpa_supplicant
bring the interface up
Call Trace:
[<ffffffffa0517490>] ? ath_hw_check+0xe0/0xe0 [ath9k]
[<ffffffff812cd1e8>] __const_udelay+0x28/0x30
[<ffffffffa03bae7a>] ar9003_get_pll_sqsum_dvc+0x4a/0x80 [ath9k_hw]
[<ffffffffa05174eb>] ath_hw_pll_work+0x5b/0xe0 [ath9k]
[<ffffffff810744fe>] process_one_work+0x11e/0x470
[<ffffffff8107530f>] worker_thread+0x15f/0x360
[<ffffffff810751b0>] ? manage_workers+0x230/0x230
[<ffffffff81079af3>] kthread+0x93/0xa0
[<ffffffff815fd3a4>] kernel_thread_helper+0x4/0x10
[<ffffffff81079a60>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff815fd3a0>] ? gs_change+0x13/0x13
ensure that the PLL-WAR for AR9485/AR9340 is executed only if the STA is
associated (or) IBSS/AP mode had started beaconing. Ideally this WAR
is needed to recover from some rare beacon stuck during stress testing.
Before the STA is associated/IBSS had started beaconing, PLL4(0x1618c)
always seem to have zero even though we had configured PLL3(0x16188) to
query about PLL's locking status. When we keep on polling infinitely PLL4's
8th bit(ie check for PLL locking measurements is done), machine hangs
due to softlockup.
fixes https://bugzilla.redhat.com/show_bug.cgi?id=811142
Reported-by: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: stable@vger.kernel.org [3.0+]
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Divider value can be zero and it makes division by zero
from debug message in s3c_fb_calc_pixclk; therefore, it
should be fixed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
All bits of SHADOWCON register should be cleared when clearing
hardware window registers; however, some bits of SHADOWCON register
are not cleared previously.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
debugfs or omapdss debug support is turned off, and fixes a suspend related
crash.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yO72
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.5-rc2' of git://gitorious.org/linux-omap-dss2/linux
Pull omapdss build problem fix from Tomi Valkeinen:
"Small fixes for omapdss driver. Most importantly, fixes a build
problem when debugfs or omapdss debug support is turned off, and fixes
a suspend related crash."
This has apparently been annoying rmk for a while..
* tag 'omapdss-for-3.5-rc2' of git://gitorious.org/linux-omap-dss2/linux:
OMAPDSS: fix registration of DPI and SDI devices
OMAPDSS: DSI: Fix bug when calculating LP command interleaving parameters
OMAPDSS: fix bogus WARN_ON in dss_runtime_put()
OMAPDSS: Taal: fix compilation warning
OMAPDSS: fix build when DEBUG_FS or DSS_DEBUG_SUPPORT disabled
version.h header file is no longer required for qla_target code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If we make a variable an unsigned int and then expect it to be < 0 on
a bad character, we're going to have a bad time. Fix the tcm_qla2xxx
code to actually notice if hex_to_bin() returns a negative variable.
This was detected by the compiler warning:
scsi/qla2xxx/tcm_qla2xxx.c: In function ‘tcm_qla2xxx_npiv_extract_wwn’:
scsi/qla2xxx/tcm_qla2xxx.c:148:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If we go to the "out_term:" exit path in qlt_do_work(), we call
qlt_send_term_exchange() with a NULL cmd, which means that it can't
possibly free the cmd for us. Add an explicit call to free the
command memory, so we don't leak the allocation.
This will also fix warnings about "BUG qla_tgt_cmd_cachep: Objects
remaining on kmem_cache_close" from slub when unloading the qla2xxx
target module.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In qlt_do_ctio_completion(), there's no point in calling
qlt_term_ctio_exchange() with a NULL cmd -- all that it does is crash
in a NULL pointer dereference, since it does
qlt_send_term_exchange(vha, cmd, &cmd->atio, 1);
and dereferencing &cmd->atio is a bad idea if cmd itself is NULL.
If we really need to do this, we could take the values from the
failed CTIO we're processing, but it's not clear if it's worth
the replumbing to do that.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When we create an explicit node ACL in tcm_qla2xxx_make_nodeacl(),
there is a call to tcm_qla2xxx_setup_nacl_from_rport(), which puts the
node ACL into the lport_fcport_map even though there is no session yet
for the initiator. Since the only time we remove entries from this
map is when we free a session, this means that if we later delete this
node ACL without the initiator ever creating a session, we'll leave
the nacl pointer in the btree pointing at freed memory.
This is especially bad if that initiator later does send us a command
that would cause us to create a dynamic ACL and session: we'll find
the stale freed nacl pointer in the btree and end up with use-after-free.
We could add more code to clear the btree entry when deleting the
explicit nacl, but the original insertion is pointless: without a
session attached, we'll just have to update the entry when a session
appears anyway. So we can just delete tcm_qla2xxx_setup_nacl_from_rport()
and the code that calls it.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The error paths in target_emulate_set_target_port_groups() are all
essentially "rc = -EINVAL; goto out;" but the code at "out:" ignores
rc and always returns success. This means that even if eg explicit
ALUA is turned off, the initiator will always see a good SCSI status
for SET TARGET PORT GROUPS.
Fix this by returning rc as is intended. It appears this bug was
added by the following patch:
commit 05d1c7c0d0
Author: Andy Grover <agrover@redhat.com>
Date: Wed Jul 20 19:13:28 2011 +0000
target: Make all control CDBs scatter-gather
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a new tcm_qla2xxx_clear_sess_lookup() call to clear session
specific s_id + loop_id entries used for se_node_acl pointer lookup ahead
of releasing se_session within the process context workqueue callback in
tcm_qla2xxx_free_session().
It makes the call in existing tcm_qla2xxx_clear_nacl_from_fcport_map()
code invoked from qlt_unreg_sess() in interrupt context w/ hardware_lock
held, ahead of the process context callback into qlt_free_session_done()
-> tcm_qla2xxx_free_session().
We are doing this to address a race between incoming ATIO or TMR packets
using stale se_node_acl pointer once session shutdown has been invoked via
qlt_unreg_sess() in qla_target.c LLD code, and when the entire tcm_qla2xxx
endpoint has not been forced into shutdown w/ echo 0 > ../$QLA2XXX_PORT/enable
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts tcm_qla2xxx code to use an internal kref_put() for
se_session->sess_kref in order to ensure that qla_hw_data->hardware_lock
can be held while calling qlt_unreg_sess() for the final put.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds an optional target_core_fabric_ops->put_session() caller
within the existing target_put_session() code path.
This is required by tcm_qla2xxx code in order to invoke it's own fabric
specific session shutdown handler using se_session->sess_kref.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The driver supports a maximum number of ports configurable at compile
time. Make sure the probe() method fails when registering a port that
exceeds the maximum instead of returning success without registering the
port.
This fixes a crash at system suspend time, when the driver tried to
suspend a non-registered port using the UART core.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When probing fails, the driver must not try to cleanup resources that
have not been initialized. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The __devinitconst section can't be referenced
from usb_serial_device structure. Thus removed it as
it done in other mos* device drivers.
Error itself:
WARNING: drivers/usb/serial/mos7840.o(.data+0x8): Section mismatch in reference
from the variable moschip7840_4port_device to the variable
.devinit.rodata:id_table
The variable moschip7840_4port_device references
the variable __devinitconst id_table
[v2] no attach now
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix memory leak introduced by commit 383cedc3bb ("USB: serial:
full autosuspend support for the option driver") which allocates
usb-serial data but never frees it.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8b4c6a3ab5 ("USB: option: Use generic USB wwan code")
moved option port-data allocation to usb_wwan_startup but still cast the
port data to the old struct...
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The low level helper returns 1 on success. The ioctl should however return
0. As this is the only user of the helper return, make the helper return 0 or
an error code.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=43009
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Later firmwares for this device now have proper subclass and
protocol info so we can identify it nicely without needing to use
the blacklist. I'm not removing the old 0xff matching as there
may be devices in the field that still need that.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Sierra Wireless AirCard 320U modem
Signed-off-by: Tomas Cassidy <tomas.cassidy@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for RT Systems USB-RTS01 USB to Serial adapter:
http://www.rtsystemsinc.com/Photos/USBRTS01.html
Tested by controlling Icom IC-718 amateur radio transceiver via hamlib.
Signed-off-by: Evan McNabb <evan@mcnabbs.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some additional IDs found in the BSD/GPL licensed out-of-tree
GobiSerial driver from Sierra Wireless.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IO_DATA_PATH_WIDTH_8 is 0, so a bit-and with it is always false. The
value IO_DATA_PATH_WIDTH covers the bits of the IO_DATA_PATH constants, so
first pick those bits and then make the test using !=.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had a boot regression in Ux500 in the merge window because
two orthogonal pin control schemes for the PL011 were merged
at the same time:
- One using the .init() and .exit() hooks into the platform
for Ux500 putting the pins into default vs sleep state
respectively as the port was started/stopped.
commit a09806607f
"ARM: ux500: switch to using pinctrl for uart0"
- One hogging the default setting at PL011 probe()
commit 258e055111
"serial: amba-pl011: adopt pinctrl support"
To get a solution that works for both let's scrap the stuff
in the platform callbacks, instead have the driver itself
select default and sleep states when the port is
started/stopped. Hopefully this works for all clients.
Platform callbacks are bad for device tree migration anyway,
so this rids us of another problem in Ux500.
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix kconfig symbol test to use "defined":
drivers/tty/serial/serial_txx9.c: warning: "CONFIG_CONSOLE_POLL" is not defined [-Wundef]
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix kernel-doc warnings in drivers/tty/serial/8250/8250.c:
Warning(drivers/tty/serial/8250/8250.c:3128): No description found for parameter 'up'
Warning(drivers/tty/serial/8250/8250.c:3128): Excess function parameter 'port' description in 'serial8250_register_8250_port'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the transmit path of the bonding driver, skb->cb is used to
stash the skb->queue_mapping so that the bonding device can set its
own queue mapping. This value becomes corrupted since the skb->cb is
also used in __dev_xmit_skb.
When transmitting through bonding driver, bond_select_queue is
called from dev_queue_xmit. In bond_select_queue the original
skb->queue_mapping is copied into skb->cb (via bond_queue_mapping)
and skb->queue_mapping is overwritten with the bond driver queue.
Subsequently in dev_queue_xmit, __dev_xmit_skb is called which writes
the packet length into skb->cb, thereby overwriting the stashed
queue mappping. In bond_dev_queue_xmit (called from hard_start_xmit),
the queue mapping for the skb is set to the stashed value which is now
the skb length and hence is an invalid queue for the slave device.
If we want to save skb->queue_mapping into skb->cb[], best place is to
add a field in struct qdisc_skb_cb, to make sure it wont conflict with
other layers (eg : Qdiscc, Infiniband...)
This patchs also makes sure (struct qdisc_skb_cb)->data is aligned on 8
bytes :
netem qdisc for example assumes it can store an u64 in it, without
misalignment penalty.
Note : we only have 20 bytes left in (struct qdisc_skb_cb)->data[].
The largest user is CHOKe and it fills it.
Based on a previous patch from Tom Herbert.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Tom Herbert <therbert@google.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we modify primary via sysfs and it is not a valid slave,
we should record it for future use, and this behavior is the same with
bond_check_params().
Signed-off-by: Weiping Pan <wpan@redhat.com>
Acked-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test procedure:
1. Start AP with security setting (e.g. WPA2)
2. Stop AP
3. Start AP with open security
Here it's observed that privacy is enabled in beacons and
probe responses.
This patch fixes it by checking the privacy parameter from
cfg80211_ap_settings. If privacy is not set in cfg80211_ap_settings,
set open authentication and no encryption in FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ad7298 drivers buffer implementation uses the IIO kfifo buffer, so it needs
to select IIO_KFIFO_BUF. Otherwise (if no other driver selects the symbol) the
following linker error will occur:
drivers/built-in.o: In function `ad7298_register_ring_funcs_and_init':
(.text+0x245cf2): undefined reference to `iio_kfifo_allocate'
drivers/built-in.o: In function `ad7298_register_ring_funcs_and_init':
(.text+0x245d7d): undefined reference to `iio_kfifo_free'
drivers/built-in.o: In function `ad7298_ring_cleanup':
(.text+0x245dcd): undefined reference to `iio_kfifo_free'
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 08224262ad as it's
just not right.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable <stable@vger.kernel.org>
Cc: Bart Westgeest <bart@elbrys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull drm fixes from Dave Airlie:
"As per your -rc2 announce, this is small and urgent only,
The radeon one is for a regression in 3.4 so we need this one in your
tree so we can send the stable one out, code in 3.4 broke some old
userspaces. The max props increase fixes spew being seen on a few
machines. And a ttm regression to fix some accounting issues that
affect vmwgfx."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/ttm: Fix buffer object metadata accounting regression v2
drm: increase DRM_OBJECT_MAX_PROPERTY to 24
drm/radeon: fix tiling and command stream checking on evergreen v3
A regression was introduced in the 3.3 rc series, commit
"drm/ttm: simplify memory accounting for ttm user v2",
causing the metadata of buffer objects created using the ttm_bo_create()
function to be accounted twice.
That causes massive leaks with the vmwgfx driver running for example
SpecViewperf Catia-03 test 2, eventually killing the app.
Furthermore, the same commit introduces a regression where
metadata accounting is leaked if a buffer object is
initialized with an illegal size. This is also fixed with this commit.
v2: Fixed an error path and removed an unused variable.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
clear the platform data pointer when mxs_pinctrl_probe_dt fails,
and also before the unregistering with pinctrl subsystem.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
if there is no purecfg , the group pointer is allocated using kzalloc and if it
fails to allocate, we wont free the new_map,
if config is true, we call kmemdup and if it
fails to do so we wont free the allocated group if there is no purecfg.
fix this by doing the frees of new_map pointer and group pointers.
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We must not look at mdev->actlog, unless we have a get_ldev() reference.
It also does not make much sense to try to disconnect or pull-ahead of
the peer, if we don't have good local data.
Only even consider congestion policies, if our local disk is D_UP_TO_DATE.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If a read is aborted due to force-detach of a supposedly unresponsive
local backing device, and retried on the peer, it can happen that the
local request later still completes (hopefully with an error).
As it may already have been completed to upper layers meanwhile,
it must not be retried again now.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
BUG: unable to handle kernel NULL pointer dereference at (null)
...
[<d1e17561>] ? _drbd_bm_set_bits+0x151/0x240 [drbd]
[<d1e236f8>] ? receive_bitmap+0x4f8/0xbc0 [drbd]
This fixes an off-by-one error in the receive_bitmap() path,
if run-length encoded bitmap transfer is enabled.
If the bitmap is an exact multiple of PAGE_SIZE, which means the visible
capacity of the drbd device is an exact multiple of 128 MiB (for 4k page
size), and bitmap compression (use-rle) is enabled (which became default
with 8.4), and the very last bit is dirty and reported in an rle
comressed bitmap packet, we ended up trying to kmap_atomic a page pointer
that does not exist (bitmap->bm_pages[last index + 1]).
bug introduced by:
Date: Fri Jul 24 15:33:24 2009 +0200
set bits: optimize for complete last word, fix off-by-one-word corner case
made effective by:
Date: Thu Dec 16 00:32:38 2010 +0100
drbd: get rid of unused debug code
Long time ago, we had paranoia code in the bitmap that allocated one
extra word, assigned a magic value, and checked on every occasion that
the magic value was still unchanged.
That debug code is unused, the extra long word complicates code a bit.
Get rid of it.
No-one triggered this bug in the last few years, because a large subset
of our userbase is unaffected:
* typically the last few blocks of a device are not modified
frequently, and remain unset
* use-rle was disabled by default in drbd < 8.4
* those with slightly "odd" device sizes, or
* drbd internal meta data (which will skew the device size slightly,
thus makes it harder to have a bug relevant device size)
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Part of the ring structure is the 'id' field which is under
control of the frontend. The frontend stamps it with "some"
value (this some in this implementation being a value less
than BLK_RING_SIZE), and when it gets a response expects
said value to be in the response structure. We have a check
for the id field when spolling new requests but not when
de-spolling responses.
We also add an extra check in add_id_to_freelist to make
sure that the 'struct request' was not NULL - as we cannot
pass a NULL to __blk_end_request_all, otherwise that crashes
(and all the operations that the response is dealing with
end up with __blk_end_request_all).
Lastly we also print the name of the operation that failed.
[v1: s/BUG/WARN/ suggested by Stefano]
[v2: Add extra check in add_id_to_freelist]
[v3: Redid op_name per Jan's suggestion]
[v4: add const * and add WARN on failure returns]
Acked-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
After create config map, the new_map pointer becomes point to
PIN_MAP_TYPE_CONFIGS_PIN map rather than PIN_MAP_TYPE_MUX_GROUP map any more.
Thus using new_map pointer to display the MUX_GROUP info is not correct.
Using map pointer instead to show the correct MUX_GROUP map info.
Original the debug message is:
imx6q-pinctrl 20e0000.iomuxc: maps: function Yp group MX6Q_PAD_SD3_CMD num 12
After fix it is:
imx6q-pinctrl 20e0000.iomuxc: maps: function usdhc3 group usdhc3grp-1 num 11
Reported-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_get_parent can return null if no parent node found, so the allocated new_map
should be freed.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
a) as we allocate the pinctrl_map structure at imx_dt_node_to_map at line 167, anyway
if its an element, or a num_elements * (sizeof(type)) elements allocated to one single
pointer must be freed only once.
CASE. A)
as new_map is not moved and allocated like,
for (i = 0; i < MAX_ELEMS; i++) {
new_map[i] = kmalloc(numelems * size, GFP_KERNEL);
}
its freed as
for (i = 0; i < MAX_ELEMS; i++) {
kfree(new_map[i]);
}
CASE. B)
and its allocated like
new_map = kmalloc(numelems * size, GFP_KERNEL);
it just needs kfree not as case A's.
b) use KERN_DEBUG facility for the IMX_PMX_DUMP macro.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit a60b57edda
"drivers/gpio: gpio-nomadik: Add support for irqdomains"
changed GPIO offset calculations to have this form:
(gpio % NMK_GPIO_PER_CHIP) except in this one place for
setting sleep mode, where the conversion was all wrong, and
instead mod:ing the GPIO with the IRQ base which does not
make any sense.
So fix this up so we can use sleepmode.
Reviewed-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
commit ec39e2ae (usb: gadget: Update fsl_qe_udc to use
usb_endpoint_descriptor inside the struct usb_ep) did
not completely convert the fsl gadget drivers to use
the desc in usb_ep as described in commit messages.
Fix the macros that were still referencing the old
pointer.
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Cc: Ido Shayevitz <idos@codeaurora.org>
[ balbi@ti.com : brush up commit log a bit ]
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixed the following bug.
https://bugzilla.kernel.org/show_bug.cgi?id=43282
This is caused by a firmware bug checking (checking generic address
register provided by firmware) in runtime. The checking should be
done in address mapping time instead of runtime to avoid too much
error reporting in runtime.
Reported-by: Pawel Sikora <pluto@agmk.net>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Tested-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
Otherwise, I got below build error when CONFIG_LEDS_CLASS=m.
LD init/built-in.o
drivers/built-in.o: In function `asic3_led_probe':
clkdev.c:(.devinit.text+0x4680): undefined reference to `led_classdev_register'
drivers/built-in.o: In function `r_tpu_probe':
clkdev.c:(.devinit.text+0x4838): undefined reference to `led_classdev_register'
drivers/built-in.o: In function `asic3_led_remove':
clkdev.c:(.devexit.text+0x564): undefined reference to `led_classdev_unregister'
drivers/built-in.o: In function `r_tpu_remove':
clkdev.c:(.devexit.text+0x5a0): undefined reference to `led_classdev_unregister'
make: *** [vmlinux] Error 1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Fixed a coding style issue relating to trailing
white space error found by checkpatch.pl tool in drivers/leds/led-class.c
Signed-off-by: Jeffrin Jose <ahiliation@yahoo.co.in>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Function led_set_software_blink() assumes that blink timer is still running,
but commit 488bc35bf4 introduced disabling
of blink timer before each call to led_set_software_blink().
Correct led_software_blink():
1) remove protection against reprogramming blink timer to the same values,
because it only disables blinking now,
2) remove unnecessary call to led_stop_software_blink().
Signed-off-by: Rafal Prylowski <prylowski@metasoft.pl>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Brown paper bag: Data valid is LSB of the ISR (status register), and NOT
of ODATA (current random data word)!
With this, rngtest is a lot happier. Before:
rngtest 3
Copyright (c) 2004 by Henrique de Moraes Holschuh
This is free software; see the source for copying conditions. There is NO warr.
rngtest: starting FIPS tests...
rngtest: bits received from input: 20000032
rngtest: FIPS 140-2 successes: 3
rngtest: FIPS 140-2 failures: 997
rngtest: FIPS 140-2(2001-10-10) Monobit: 604
rngtest: FIPS 140-2(2001-10-10) Poker: 996
rngtest: FIPS 140-2(2001-10-10) Runs: 36
rngtest: FIPS 140-2(2001-10-10) Long run: 0
rngtest: FIPS 140-2(2001-10-10) Continuous run: 117
rngtest: input channel speed: (min=622.371; avg=23682.481; max=28224.350)Kibitss
rngtest: FIPS tests speed: (min=12.361; avg=12.718; max=12.861)Mibits/s
rngtest: Program run time: 2331696 microsecondsx
After:
rngtest 3
Copyright (c) 2004 by Henrique de Moraes Holschuh
This is free software; see the source for copying conditions. There is NO warr.
rngtest: starting FIPS tests...
rngtest: bits received from input: 20000032
rngtest: FIPS 140-2 successes: 999
rngtest: FIPS 140-2 failures: 1
rngtest: FIPS 140-2(2001-10-10) Monobit: 0
rngtest: FIPS 140-2(2001-10-10) Poker: 0
rngtest: FIPS 140-2(2001-10-10) Runs: 1
rngtest: FIPS 140-2(2001-10-10) Long run: 0
rngtest: FIPS 140-2(2001-10-10) Continuous run: 0
rngtest: input channel speed: (min=777.363; avg=43588.270; max=47870.711)Kibitss
rngtest: FIPS tests speed: (min=11.943; avg=12.716; max=12.844)Mibits/s
rngtest: Program run time: 1955282 microseconds
Cc: stable@vger.kernel.org
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Reported-by: George Pontis <GPontis@z9.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Previously a 6 byte array (buf) was erroneously cast to a 8 byte long
(event_bits) on 64-bit architectures which caused a stack corruption.
Signed-off-by: Bart Westgeest <bart@elbrys.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change adds support for the tilegx network driver based on the
GXIO IORPC support in the tilegx software stack, using the on-chip
mPIPE packet processing engine.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
5906 devices also need the short DMA fragment workaround. This patch
makes the necessary change.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Tested-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calls to optional subsystems cannot be made indiscriminately.
Enclose all of the usb helper functions inside
#if IS_ENABLED(CONFIG_USB)
to fix these build errors.
(The pci helper functions are OK since there are stubs in
linux/pci.h for the called functions when PCI is not enabled.
Possibly the same could be done for the called USB functions.)
ERROR: "usb_deregister" [drivers/staging/comedi/comedi.ko] undefined!
ERROR: "usb_register_driver" [drivers/staging/comedi/comedi.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_{un}prepare is mandatory for platforms using common clock framework.
Since these drivers are used by SPEAr platform, which supports common
clock framework, add clk_{un}prepare() support for them. Otherwise
the clocks are not correctly en-/disabled and ethernet support doesn't
work.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the documentation of the Y4 and Y6 formats.
Fix a poll() issue, add support for enum_frmsizes, set the proper
parent device and fix a few compliance issues.
Tested with an actual Connectix B&W parallel port webcam, both on a
little-endian and a big-endian platform. This driver has never been
so good, doing 320x240 at 1 frame per second :-)
I know, nobody cares, but still it is cool that linux can still support
this old webcam.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
base_addr has type resource_size_t, which may be 64 bits.
Also fix a few endian issues related to mailboxes and firmware loading.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
base_addr has type resource_size_t, which may be 64 bits on a 32-bit ppc.
Tested on my ppc board.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The frequency range of the current tuner (radio or TV) was returned
instead of the frequency range of the requested tuner (which depends
on the device node).
This bug caused the frequency range of the radio tuner to be returned
when G_TUNER was called on a video node.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The field current_norm does not have to be set for g_parm to be a valid
ioctl. Remove that check, but add a check whether this is a video node
instead as g_parm only makes sense for those nodes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If g_parm is handled automatically, then set readbuffers to 2, which is the
minimum number of buffers videobuf uses.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
__lpc_handle_xmit() has two bugs :
1) It can leak skbs in case TXSTATUS_ERROR is set
2) It can wake up txqueue while no slot was freed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Roland Stigge <stigge@antcom.de>
Tested-by: Roland Stigge <stigge@antcom.de>
Cc: Kevin Wells <kevin.wells@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lpc_eth does a copy of transmitted skbs to DMA area, without checking
skb lengths, so can trigger buffer overflows :
memcpy(pldat->tx_buff_v + txidx * ENET_MAXF_SIZE, skb->data, len);
One way to get bigger skbs is to allow MTU changes above the 1500 limit.
Calling eth_change_mtu() in ndo_change_mtu() makes sure this cannot
happen.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Roland Stigge <stigge@antcom.de>
Cc: Kevin Wells <kevin.wells@nxp.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
v4l-dvb-git/drivers/media/video/vino.c: In function 'vino_acquire_input':
v4l-dvb-git/drivers/media/video/vino.c:2602:18: warning: 'data_norm' may be used uninitialized in this function [-Wuninitialized]
v4l-dvb-git/drivers/media/video/vino.c: In function 'vino_set_input':
v4l-dvb-git/drivers/media/video/vino.c:2690:19: warning: 'data_norm' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l-dvb-git/drivers/media/dvb/frontends/cx24110.c: In function ‘cx24110_read_ucblocks’:
v4l-dvb-git/drivers/media/dvb/frontends/cx24110.c:520:40: warning: value computed is not used [-Wunused-value]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The webcam 0458:7025 (Eye911Q) has:
- an inverted power pin,
- a sensor mi0360b which cannot be probed.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ov534 bridge is too slow to handle the sensor accesses
requested by fast hosts giving 'sccb_reg_write failed'.
A small delay fixes the problem.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes a regression introduced by commit f7059ea and should be
backported to all supported stable kernels which have this commit.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Antonio Ospite <ospite@studenti.unina.it>
CC: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Even if the best results are indeed achieved with both AGC and AWB
enabled, the webcam is capable of setting these independently, and the
user can see the difference of any of the 4 combinations of these two
boolean controls.
Removing the dependency from one another simplifies the code and gives
more control to the user.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This avoids the need for a re-alloc during init.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The (radio) audio out from the tuner (which can also demod FM radio) does not
seem to be hooked up to the msp3410 on this board in any way, so the only way
to get sound from the radio part is to make the msp3410 do the FM radio demod.
The msp3410 can handle this fine, but it is a bit weird compared to how it
is handled on other boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
bttv_init_card2() sets btv->has_audio to a *default* value from the tvcards
array and then may update it by reading a card specific eeprom or gpio
detection.
After bttv_init_card2(), bttv_init_tuner() gets called, and it should clearly
use the updated, dynamic has_radio value from btv->has_radio, rather then
the const value in the tvcards array.
This fixes the radio not working on my Hauppauge WinTV.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before this patch the owner field of the /dev/radio# device fops was set to
the snd-tea575x-tuner module itself. Meaning that the module which was using
it could be rmmod-ed while the device is open, and then BAD things happen.
I know, as I found out the hard way :)
Note that there is no need to also somehow increase the refcount of the
snd-tea575x-tuner module itself, since any drivers using it will have
symbolic references to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
CC: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix an off-by-one error in lg216x_write_regs, causing the last element
of the lg216x init block to be ignored. Spotted by Dan Carpenter.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now query/enum_dv_timings finally work again.
The timings API patches and the core ioctl changes clearly sailed right past
each other without realizing that both needed to adapt to the other.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
rndis_check_bssid_list() originally tried to check if bssid->mac and
match_bssid are equal using compare_ether_addr() when it should use
!compare_ether_addr(). This check was added by commit
b5257c952d as part of workaround for
hardware issue.
Commit 2e42e4747e that replaced
compare_ether_addr with ether_addr_equal relieved that this compare
to be inverse of what it should be.
Compare was added as response to hardware bug, where bssid-list does
not contain BSSID and other information of currently connected AP
(spec insists that device must provide this information in the list
when connected). Lack bssid-data on current connection then causes
WARN_ON somewhere in cfg80211. Workaround was to check if bssid-list
returns current bssid and if it does not, manually construct bssid
information in other ways. And this workaround worked, with inverse
check. Which must mean that when hardware is experiencing the problem,
it's actually returning empty bssid-list and this check didn't make
any difference for workaround.
However inverse check causes workaround be activated when bssid-list
returns only entry, currently connected BSSID. That does not cause
problems in itself, just slightly more inaccurate information in
scan-list.
Cc: Joe Perches <joe@perches.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'cfg80211: fix interface combinations' ensures that if an interface
type is not advertised by the driver in any of the interface combinations
(via ieee80211_iface_combination) then it shall be treated as a single
incompatible interface. if there are more than one interfaces present
and changing them to incompatible interface type is not possible.
These checks will be properly handled by cfg80211_change_iface ->
cfg80211_can_change_interface.
this patch is dependent on 'cfg80211: fix interface combinations'
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this patch is dependent on the patch "cfg80211: fix interface
combinations"
In ath9k currently we have ADHOC interface as a single incompatible
interface. when drv_add_interface is called during resume we got to
consider number of vifs already present in addition to checking the
drivers 'opmode' information about ADHOC. we incorrectly assume
an ADHOC interface is already present. Then we may miss some driver
specific data for the ADHOC interface after resume.
The above mentioned checks can be removed from the driver,
as the patch 'cfg80211: fix interface combinations' ensures that
if an interface type is not advertised by the driver in any of the
interface combinations(via ieee80211_iface_combination) then it shall
be treated as a single incompatible interface. Fixes the following
warning on suspend/resume with ibss interface.
ath: phy0: Cannot create ADHOC interface when other
interfaces already exist.
WARNING: at net/mac80211/driver-ops.h:12
ieee80211_reconfig+0x1882/0x1ca0 [mac80211]()
Hardware name: 2842RK1
wlan2: Failed check-sdata-in-driver check, flags: 0x0
Call Trace:
[<c01361b2>] warn_slowpath_common+0x72/0xa0
[<f8aaa7c2>] ? ieee80211_reconfig+0x1882/0x1ca0
[mac80211]
[<f8aaa7c2>] ? ieee80211_reconfig+0x1882/0x1ca0
[mac80211]
[<c0136283>] warn_slowpath_fmt+0x33/0x40
[<f8aaa7c2>] ieee80211_reconfig+0x1882/0x1ca0 [mac80211]
[<c06c1d1a>] ? mutex_lock_nested+0x23a/0x2f0
[<f8a95097>] ieee80211_resume+0x27/0x70 [mac80211]
[<fd177edf>] wiphy_resume+0x8f/0xa0 [cfg80211]
Cc: stable@vger.kernel.org
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a regression introduced by commit
5126f2590bee412e3053de851cb07f531e4be36a:
[media] v4l2-dev: add flag to have the core lock all file operations
I forgot to add the locks to the vivi read operation.
Regards,
Hans
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix RQ/SRQ error CQE polling. Return error CQE to consumer for error
case which was not returned previously.
Signed-off-by: Parav Pandit <parav.pandit@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix max sge calculation for sq, rq, srq for all hardware types.
Signed-off-by: Mahesh Vardhamanaiah <mahesh.vardhamanaiah@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix code to read the max wqe and max rqe values from mailbox response.
Signed-off-by: Mahesh Vardhamanaiah <mahesh.vardhamanaiah@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
1. Fix reporting GID table addition events.
2. Enable vlan based GID entries only when VLAN is enabled at compile
time (test CONFIG_VLAN_8021Q / CONFIG_VLAN_8021Q_MODULE).
Signed-off-by: Parav Pandit <parav.pandit@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The logic was checking the sizeof the structure being allocated to
determine whether an alignment fixup was required. This isn't right;
what we actually care about is the alignment of the actual pointer that's
about to be returned. This became an issue recently because struct
edac_mc_layer has a size that is not zero modulo eight, so we were
taking the correctly-aligned pointer and forcing it to be misaligned.
On Tile this caused an alignment exception.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
During unload, don't cleanup the framebuffer if it is not valid.
Signed-off-by: Andy Gross <andy.gross@ti.com>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca0907b "edac: Remove the legacy EDAC ABI" broke mpc85xx_edac
in the following manner:
mpc85xx_edac.c:983:35: error: too few arguments to function 'edac_mc_alloc'
this patch puts back the missing 'layers' argument.
[mchehab@redhat.com: As Ben sent a similar fix, I added his SOB on this patch]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On SandyBridge, DDRIOA(Dev: 17 Func: 0 Offset: 328) is used
to detect whether DIMM is RDIMM/LRDIMM, not TA(Dev: 15 Func: 0).
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some edac drivers register themselves as mce decoders via
notifier_chain. But in current notifier_chain implementation logic,
it doesn't accept same notifier registered twice. If so, it will be
wrong when adding/removing the element from the list. For example,
on one SandyBridge platform, remove module sb_edac and then trigger
one error, it will hit oops because it has no mce decoder registered
but related notifier_chain still points to an invalid callback
function. Here is an example:
Call Trace:
[<ffffffff8150ef6a>] atomic_notifier_call_chain+0x1a/0x20
[<ffffffff8102b936>] mce_log+0x46/0x180
[<ffffffff8102eaea>] apei_mce_report_mem_error+0x4a/0x60
[<ffffffff812e19d2>] ghes_do_proc+0x192/0x210
[<ffffffff812e2066>] ghes_proc+0x46/0x70
[<ffffffff812e20d8>] ghes_notify_sci+0x48/0x80
[<ffffffff8150ef05>] notifier_call_chain+0x55/0x80
[<ffffffff81076f1a>] __blocking_notifier_call_chain+0x5a/0x80
[<ffffffff812aea11>] ? acpi_os_wait_events_complete+0x23/0x23
[<ffffffff81076f56>] blocking_notifier_call_chain+0x16/0x20
[<ffffffff812ddc4d>] acpi_hed_notify+0x19/0x1b
[<ffffffff812b16bd>] acpi_device_notify+0x19/0x1b
[<ffffffff812beb38>] acpi_ev_notify_dispatch+0x67/0x7f
[<ffffffff812aea3a>] acpi_os_execute_deferred+0x29/0x36
[<ffffffff81069dc2>] process_one_work+0x132/0x450
[<ffffffff8106bbcb>] worker_thread+0x17b/0x3c0
[<ffffffff8106ba50>] ? manage_workers+0x120/0x120
[<ffffffff81070aee>] kthread+0x9e/0xb0
[<ffffffff81514724>] kernel_thread_helper+0x4/0x10
[<ffffffff81070a50>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff81514720>] ? gs_change+0x13/0x13
Code: f3 49 89 d4 45 85 ed 4d 89 c6 48 8b 0f 74 48 48 85 c9 75 17 eb 41
0f 1f 80 00 00 00 00 41 83 ed 01 4c 89 f9 74 22 4d 85 ff 74 1d <4c> 8b
79 08 4c 89 e2 48 89 de 48 89 cf ff 11 4d 85 f6 74 04 41
RIP [<ffffffff8150eef6>] notifier_call_chain+0x46/0x80
RSP <ffff88042868fb20>
CR2: ffffffffa01af838
---[ end trace 0100930068e73e6f ]---
BUG: unable to handle kernel paging request at fffffffffffffff8
IP: [<ffffffff810705b0>] kthread_data+0x10/0x20
PGD 1a0d067 PUD 1a0e067 PMD 0
Oops: 0000 [#2] SMP
Only i7core_edac and sb_edac have such issues because they have more
than one memory controller which means they have to register mce
decoder many times.
Cc: <stable@vger.kernel.org> # 3.2 and upper
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull crypto fixes from Herbert Xu:
"This push fixes an unaligned fault on x86-32 with aesni-intel and an
RNG failure with atmel-rng (repeated bits)."
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: aesni-intel - fix unaligned cbc decrypt for x86-32
hwrng: atmel-rng - fix race condition leading to repeated bits
Trying to "modprobe dummy numdummies=30000" triggers :
INFO: rcu_sched self-detected stall on CPU { 8} (t=60000 jiffies)
After this splat, RTNL is locked and reboot is needed.
We must call cond_resched() to avoid this, even holding RTNL.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switches over to the now exported clockevents_config() and
clockevents_config_and_register() helpers. This knocks off a
long-standing TMU TODO item.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Nothing too exciting - a cleanup for debugfs in error handling and a fix
for the padding (which has only just acquired real use) and exporting a
function that's supposed to be usable by drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJP0SRCAAoJEBus8iNuMP3dy4EP/j5Wb0riwgfkaNhXvhNA4APL
d4CkoBT3N4JC6ti6nstPR5ng/mNc/NGHzVVPn1xF4VfZuAv8A188z7tlqGc7B/fY
zHbB4sM6o92Da3PUIRpsWLIijLqsVQ6T8CEXddd1UNxU0YryoWWoW+ESxvJ1v2Mt
0zM3fRRpT3TbQo84Hki2p3nNz8HJk9ckqZnH+GOLIBo8aZucMIuEmD6L+J9aMpoH
U187d+voVzCWJ7SnhiTmQPPJpL045/CLto2U0msbgjetlpOiRzvmoAlF1DtqgMQi
HeKQPuH3DAPwhxyTATHy7y51ttEziqzePWppm3wIVtdZ1+Ls395AKlkPWHYZV6oG
5sUdNq1feH+pdxxjhP9qI/zzjvsECAd8duGLY18ijN12Q3otBeZ4Js2qJn+Qnqlz
c/UVbvdjy2NJiMSKulWp9Mb9Z1zDnucfWK4skqNhUvNGBdEVae3xhD6WVpkGtM1j
jb9a5eoDLVV1CEr3DZD/4au6+oDKTU57V0V8g06nH63N9QN3giY8Kexsn8IK7k05
vQyGfWTZY9o3Hn6G4jOC6dopBjl9gUF+KRc94ZGawY90+xoK7LZXRkYZPs1k2ECK
Av7Jaa7weKxA9fUFFoit4DLjgZUiL/5im3cuAEjHNJOmh2VwCA1hP/taD8TZdfHN
acStYoQ1y5R6xLP/tiPQ
=F5A2
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Nothing too exciting - a cleanup for debugfs in error handling and a
fix for the padding (which has only just acquired real use) and
exporting a function that's supposed to be usable by drivers."
* tag 'regmap-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Export regmap_reinit_cache()
regmap: Fix the size calculation for map->format.buf_size
regmap: clean up debugfs if regmap_init fails
A couple of small fixes, plus larger fixes for the gpio-regulator driver
the most recent changes for which had apparently not been tested at all
in -next (or elsewhere from the looks of it).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8FA4
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of small fixes, plus larger fixes for the gpio-regulator
driver the most recent changes for which had apparently not been
tested at all in -next (or elsewhere from the looks of it)."
* tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: Properly handle the case min_uV < rdev->desc->min_uV in map_voltage_linear
regulator: max8649: fix missing regmap in rdev
regulator: gpio-regulator: populate selector from set_voltage
regulator: gpio-regulator: Fix finding of smallest value
regulator: gpio-regulator: do not pass drvdata pointer as reference
regulator: anatop: Use correct __devexit_p annotation
regulator: palmas: Fix wrong kfree calls
commit 3fa2a1df90 (virtio-net: per cpu 64 bit stats (v2)) added a race
on 32bit arches.
We must use separate syncp for rx and tx path as they can be run at the
same time on different cpus. Thus one sequence increment can be lost and
readers spin forever.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reworking the r8169 driver a few months ago to perform the
smallest amount of work in the irq handler, I took care of avoiding
any irq mask register operation in the slow work dedicated user
context thread. The slow work thread scheduled an extra round of NAPI
work which would ultimately set the irq mask register as required,
thus keeping such irq mask operations in the NAPI handler.
It would eventually race with the irq handler and delay NAPI execution
for - assuming no further irq - a whole ksoftirqd period. Mildly a
problem for rare link changes or corner case PCI events.
The race was always lost after the last bh disabling lock had been
removed from the work thread and people started wondering where those
pesky "NOHZ: local_softirq_pending 08" messages came from.
Actually the irq mask register _can_ be set up directly in the slow
work thread.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Marc Dionne <marc.c.dionne@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix regresson since the introduction of command stream checking on
evergreen (thread referenced below). Issue is cause by ddx allocating
bo with formula width*height*bpp while programming the GPU command
stream with ALIGN(height, 8). In some case (where page alignment does
not hide the extra size bo should be according to height alignment)
the kernel will reject the command stream.
This patch reprogram the command stream to slice - 1 (slice is
a derivative value from height) which avoid rejecting the command
stream while keeping the value of command stream checking from a
security point of view.
This patch also fix wrong computation of layer size for 2D tiled
surface. Which should fix issue when 2D color tiling is enabled.
This dump the radeon KMS_DRIVER_MINOR so userspace can know if
they are on a fixed kernel or not.
https://lkml.org/lkml/2012/6/3/80https://bugs.freedesktop.org/show_bug.cgi?id=50892https://bugs.freedesktop.org/show_bug.cgi?id=50857
!!! STABLE need a custom version of this patch for 3.4 !!!
v2: actually bump the minor version and add comment about stable
v3: do compute the height the ddx was trying to use
[airlied: drop left over debug]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If rproc_find_rsc_table() fails, rproc_fw_boot() must set
return-value before jumping to clean_up label. Otherwise no
error value is returned.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: stable@vger.kernel.org
Fix compile warnings from GCC 4.6.1 when printing values of type size_t.
drivers/remoteproc/remoteproc_core.c:251:6:
warning: format ‘%x’ expects argument of type ‘unsigned int’,
but argument 4 has type ‘size_t’ [-Wformat]
drivers/remoteproc/remoteproc_core.c:938:9:
warning: format ‘%u’ expects argument of type ‘unsigned int’,
but argument 4 has type ‘size_t’ [-Wformat]
drivers/remoteproc/remoteproc_core.c:1023:2:
warning: format ‘%d’ expects argument of type ‘int’,
but argument 4 has type ‘size_t’ [-Wformat]
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: stable@vger.kernel.org
Long delays need to use mdelay on architectures such as ARM
that cannot compute long timeouts in udelay.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The frame buffer console needs at least one font to be built into
the kernel, so add the necessary Kconfig magic to guarantee that
one of the available font is always on. If a user accidentally
disables all fonts manually, the 8x16 font will be selected
anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
No symbol can be exported when the section is discarded - the only
solution I could think of is not to mark symbols as __devexit
when they are exported.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
__devexit functions are discarded when CONFIG_HOTPLUG
is not set, so the symbol needs to be referenced carefully.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
As of edbc454 [mtd: driver _read() returns max_bitflips; mtd_read()
returns -EUCLEAN], 'mtd->bitflip_threshold' must be set for mtd devices
having ECC, prior any 'mtd_read()' call.
Otherwise, 'mtd_read()' will falsely return -EUCLEAN.
Normally, 'mtd->bitflip_threshold' is initialized when the MTD is added.
However, this is too late for NAND MTDs, as 'scan_bbt()' is invoked
prior the existing initialization of 'mtd->bitflip_threshold'.
This is a problem since 'scan_bbt()' calls 'mtd_read()', in the case
of a flash-based bad block table.
It resulted in a falsely reported bitflips indication during BBT read,
which lead to constant scrubbing of the flash BBT blocks.
Initialize 'mtd->bitflip_threshold' to its default value (if not already
set by the driver), prior to invocation of 'scan_bbt()'.
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The audio clients have to be disabled before disabling the VGA and
switching. Similarly, enabling the audio client should be done at
last. Otherwise the audio-side operation stalls, eventually leading
to Oops or lockups.
Tested-by: Jörg-Volker Peetz <jvpeetz@web.de>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix kernel-doc warnings in drivers/net/phy:
Warning(drivers/net/phy/mdio_bus.c:109): No description found for parameter 'mdio_bus_np'
Warning(drivers/net/phy/mdio_bus.c:109): Excess function parameter 'mdio_np' description in 'of_mdio_find_bus'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 9e612a008f.
It incorrectly finds VGA connectors where none are attached, apparently
not noticing that nothing replied to the EDID queries, and happily using
the default EDID modes that have nothing to do with actual hardware.
That in turn then causes X to fall down to the lowest common
denominator, which is usually the default 1024x768 mode that is in the
default EDID and pretty much anything supports).
I'd suggest that if not relying on the HDP pin, the code should at least
check whether it gets valid EDID data back, rather than just assume
there's something on the VGA connector.
Cc: Dave Airlie <airlied@linux.ie>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As soon as hardware is notified of a transmit, we no longer can assume
skb can be dereferenced, as TX completion might have freed the packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
broken by the 3.5-rc1 UBI/UBIFS changes when we removed the debugging
Kconfig switches.
Also, correct locking in 'ubi_wl_flush()' - it was extended to support
flushing a specific LEB in 3.5-rc1, and the locking was sub-optimal.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=X7QS
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.5-rc2' of git://git.infradead.org/linux-ubifs
Pull UBI/UBIFS fixes from Artem Bityutskiy:
"Fix UBI and UBIFS - they refuse to work without debugfs. This was
broken by the 3.5-rc1 UBI/UBIFS changes when we removed the debugging
Kconfig switches.
Also, correct locking in 'ubi_wl_flush()' - it was extended to support
flushing a specific LEB in 3.5-rc1, and the locking was sub-optimal."
* tag 'upstream-3.5-rc2' of git://git.infradead.org/linux-ubifs:
UBI: correct ubi_wl_flush locking
UBIFS: fix debugfs-less systems support
UBI: fix debugfs-less systems support
This feature has been reported to be buggy and enabled by
default. We therefore need to disable it manually.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we remove a key, we put a key index which was supposed
to tell the fw that we are actually removing the key. But
instead the fw took that index as a valid index and messed
up the SRAM of the device.
This memory corruption on the device mangled the data of
the SCD. The impact on the user is that SCD queue 2 got
stuck after having removed keys.
The message is the log that was printed is:
Queue 2 stuck for 10000ms
This doesn't seem to fix the higher queues that get stuck
from time to time.
Cc: stable@vger.kernel.org [2.6.27+]
Reviewed-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pc could be null if hosttype != BCMA_HOSTTYPE_PCI.
If we are on a device without a pci core this function is called with
pc = null by b43 and brcmsmac. If the host type is PCI we have a pci
core as well and pc can not be null.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this patch fixes kernel Oops on "rmmod b43" if firmware was not loaded:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000088
IP: [<ffffffff8104e988>] drain_workqueue+0x25/0x142
PGD 153ac6067 PUD 153b82067 PMD 0
Oops: 0000 [#1] SMP
Signed-off-by: Oleksij Rempel <bug-track@fisher-privat.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My patch
iwlwifi: use correct released ucode version
did not correctly report supported firmware
for the 6035 device. This patch fixes it. The
minimum supported firmware version for 6035
is v6.
Also correct the minimum supported firmware
version for the 6000g2 series of devices.
Cc: stable@kernel.org
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The station fail average is not updated correctly since the
IEEE80211_STAT_ACK flag is not set when using wmediumd with
mac80211_hwsim. Set this flag when wmediumd indicates that the frame
was successfully transmitted (eventually).
Signed-off-by: Qasim Javed <qasimj@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix:
BUG: sleeping function called from invalid context at kernel/workqueue.c:2547
in_atomic(): 1, irqs_disabled(): 0, pid: 629, name: wpa_supplicant
2 locks held by wpa_supplicant/629:
#0: (rtnl_mutex){+.+.+.}, at: [<c08b2b84>] rtnl_lock+0x14/0x20
#1: (&trigger->leddev_list_lock){.+.?..}, at: [<c0867f41>] led_trigger_event+0x21/0x80
Pid: 629, comm: wpa_supplicant Not tainted 3.3.0-0.rc3.git5.1.fc17.i686
Call Trace:
[<c046a9f6>] __might_sleep+0x126/0x1d0
[<c0457d6c>] wait_on_work+0x2c/0x1d0
[<c045a09a>] __cancel_work_timer+0x6a/0x120
[<c045a160>] cancel_delayed_work_sync+0x10/0x20
[<f7dd3c22>] rtl8187_led_brightness_set+0x82/0xf0 [rtl8187]
[<c0867f7c>] led_trigger_event+0x5c/0x80
[<f7ff5e6d>] ieee80211_led_radio+0x1d/0x40 [mac80211]
[<f7ff3583>] ieee80211_stop_device+0x13/0x230 [mac80211]
Removing _sync is ok, because if led_on work is currently running
it will be finished before led_off work start to perform, since
they are always queued on the same mac80211 local->workqueue.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=795176
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull drm intel and exynos fixes from Dave Airlie:
"A bunch of fixes for Intel and exynos, nothing too major, a new intel
PCI ID, and a fix for CRT detection."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: pch_irq_handler -> {ibx, cpt}_irq_handler
char/agp: add another Ironlake host bridge
drm/i915: fix up ivb plane 3 pageflips
drm/exynos: fixed blending for hdmi graphic layer
drm/exynos: Remove dummy encoder get_crtc operation implementation
drm/exynos: Keep a reference to frame buffer GEM objects
drm/exynos: Don't cast GEM object to Exynos GEM object when not needed
drm/exynos: DRIVER_BUS_PLATFORM is not a driver feature
drm/exynos: fixed size type.
drm/exynos: Use DRM_FORMAT_{NV12, YUV420} instead of DRM_FORMAT_{NV12M, YUV420M}
drm/i915: hold forcewake around ring hw init
drm/i915: Mark the ringbuffers as being in the GTT domain
drm/i915/crt: Do not rely upon the HPD presence pin
drm/i915: Reset last_retired_head when resetting ring
Add vga_switcheroo_get_client_state() to get the current state of the
client. This is necessary to determine the proper initial state of
audio clients in HD-audio driver.
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'exynos-drm-fixes' of git://git.infradead.org/users/kmpark/linux-samsung:
drm/exynos: fixed blending for hdmi graphic layer
drm/exynos: Remove dummy encoder get_crtc operation implementation
drm/exynos: Keep a reference to frame buffer GEM objects
drm/exynos: Don't cast GEM object to Exynos GEM object when not needed
drm/exynos: DRIVER_BUS_PLATFORM is not a driver feature
drm/exynos: fixed size type.
drm/exynos: Use DRM_FORMAT_{NV12, YUV420} instead of DRM_FORMAT_{NV12M, YUV420M}
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: pch_irq_handler -> {ibx, cpt}_irq_handler
char/agp: add another Ironlake host bridge
drm/i915: fix up ivb plane 3 pageflips
drm/i915: hold forcewake around ring hw init
drm/i915: Mark the ringbuffers as being in the GTT domain
drm/i915/crt: Do not rely upon the HPD presence pin
drm/i915: Reset last_retired_head when resetting ring
This reverts commit efa230f2c6.
BQL doesn't work with how this driver currently only takes TX
interrupts every 1/4 of the TX ring. That behavior needs to be fixed,
but that's a larger non-trivial task and for now we have to revert
BQL support as this makes the device currently completely unusable.
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit ba27ec66ff fixes the Kconfig of the
driver when built as module allowing to select/unselect
the PCI and Platform modules that are not anymore mutually
exclusive. This patch fixes and guarantees that the driver
builds on all the platforms w/ w/o PCI and when select/unselect
the two stmmac supports. In case of there are some problems
on both the configuration and the pci/pltf registration the
module_init will fail.
v2: set the CONFIG_STMMAC_PLATFORM enabled by default.
I've just noticed that this can actually help on
some configurations that don't enable any STMMAC
options by default (e.g. SPEAr).
v3: change printk level when do not register the driver.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Properly handle the case if the specified min_uV is less than the voltage given
by the lowest selector.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Correct mail address reference to a mail account which I actually read.
Signed-off-by: Borislav Petkov <bp@alien8.de>
Cc: Peter Feuerer <peter@piie.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The newer flavors of Yukon II use a different method for receive
checksum offload. This is indicated in the driver by the SKY2_HW_NEW_LE
flag. On these newer chips, the BMU_ENA_RX_CHKSUM should not be set.
The driver would get incorrectly toggle the bit, enabling the old
checksum logic on these chips and cause a BUG_ON() assertion. If
receive checksum was toggled via ethtool.
Reported-by: Kirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit "62f38455 UBI: modify ubi_wl_flush function to clear work queue for a lnum"
takes the 'work_sem' semaphore in write mode for the entire loop, which is not
very good because it will block other workers for potentially long time. We do
not need to have it in write mode - read mode is enough, and we do not need to
hole it over the entire loop. So this patch turns changes the locking: takes
'work_sem' in read mode and pushes it down to the loop.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The iommu_shutdown callback is not initialized when the AMD
IOMMU driver runs in passthrough mode. Fix that by moving
the callback initialization before the check for
passthrough mode.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Fixes the following sparse warning:
drivers/dma/pl330.c:2542:5: warning: symbol 'add_desc' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This fix audio underrun issue. When SNDRV_PCM_TRIGGER_STOP
and SNDRV_PCM_TRIGGER_START, it calls prepare again. buf_tail
should be reset to zero.
So move buf_tail initialization into prepare function.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Commit eab2158558 ("dmaengine: pl330: dont complete descriptor for
cyclic dma") wrongly completes descriptor for cyclic dma, hence following
BUG_ON is still hit with cyclic DMA operations.
kernel BUG at drivers/dma/dmaengine.h:53!
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Commit "aa44d1d UBI: remove Kconfig debugging option" broke UBI and it
refuses to initialize if debugfs (CONFIG_DEBUG_FS) is disabled. I incorrectly
assumed that debugfs files creation function will return success if debugfs
is disabled, but they actually return -ENODEV. This patch fixes the issue.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
With CONFIG_BLK_DEV_SD = n and CONFIG_PM = n, you get this compile failure:
(.text+0x4f6c77): undefined reference to `scsi_sd_probe_domain'
This was introduced by
commit a7a20d1039
Author: Dan Williams <dan.j.williams@intel.com>
Date: Thu Mar 22 17:05:11 2012 -0700
[SCSI] sd: limit the scope of the async probe domain
And happens because scsi_sd_probe_domain is conditionally defined but
unconditionally used. Fix this by making the symbol unconditionally defined.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Dan Williams <dan.j.williams@intel.com>
Tested-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Cougar/Panther Point redefine the bits in SDEIIR pretty completely.
This function is just debugging, but if we're debugging we probably want
to be told accurate things instead of lies.
I'm told Lynx Point changes this yet more, but I have no idea how...
Note from Eugeni's review:
"For the record and for future enabling efforts, for LPT, bits 28-31
and 1-14 are gone since CPT/PPT (e.g., those must be zero). And there
is the bit 15 as a new addition, but we are not using it yet and
probably won't be using in foreseeable future."
Signed-off-by: Adam Jackson <ajax@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35103
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull ACPI and Power Management changes from Len Brown.
This does an evil merge to fix up what I think is a mismerge by Len to
the gma500 driver, and restore it to the mainline state.
In that driver, both branches had commented out the call to
acpi_video_register(), and Len resolved the merge to that commented-out
version.
However, in mainline, further changes by Alan (commit d839ede47a56:
"gma500: opregion and ACPI" to be exact) had re-enabled the ACPI video
registration, so the current state of the driver seems to want it.
Alan is apparently still feeling the effects of partying with the Queen,
so he didn't reply to my query, but I'll do the evil merge anyway.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
ACPI: fix acpi_bus.h build warnings when ACPI is not enabled
drivers: acpi: Fix dependency for ACPI_HOTPLUG_CPU
tools/power turbostat: fix IVB support
tools/power turbostat: fix un-intended affinity of forked program
ACPI video: use after input_unregister_device()
gma500: don't register the ACPI video bus
acpi_video: Intel video is not always i915
acpi_video: fix leaking PCI references
ACPI: Ignore invalid _PSS entries, but use valid ones
ACPI battery: only refresh the sysfs files when pertinent information changes
Adding device IDs for Aircard 320U and two other devices
found in the out-of-tree version of this driver.
Cc: linux@sierrawireless.com
Cc: Autif Khan <autif.mlist@gmail.com>
Cc: Tom Cassidy <tomas.cassidy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 452503ebc (ARM: Orion: Eth: Add clk/clkdev support.) broke
the building of the driver on architectures which don't have clk
support. In particular PPC32 Pegasos which uses this driver.
Add #ifdef around the clk API usage.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use correct format string parameter for the peak datarate, and prevent
uninitialized use of cycle_time.
Signed-off-by: Christian Dietrich <christian.dietrich@informatik.uni-erlangen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The icside driver can be configured without DMA support, but it
doesn't compile then, because DMA operations are referenced.
drivers/ide/icside.c:523: error: 'icside_v6_port_ops' undeclared
drivers/ide/icside.c:522: error: 'icside_dma_init' undeclared
Signed-off-by: Christian Dietrich<christian.dietrich@informatik.uni-erlangen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Limit the max number of WQEs per QP reported when querying the
device, so that ib_create_qp() will not fail for a QP size that the
device claimed to support due to additional headroom WQEs being
allocated.
2. Limit qp resources accepted for ib_create_qp() to the limits
reported in ib_query_device(). In kernel space, make sure that the
limits returned to the caller following qp creation also lie within
the reported device limits. For userspace, report as before, and do
adjustment in libmlx4 (so as not to break ABI).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Sagi Grimberg <sagig@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 096335b3f9 ("mlx4_core: Allow dynamic MTU configuration for
IB ports") modifies the port VL setting. This exposes a bug in
mlx4_common_set_port(), where the VL cap value passed in (inside the
command mailbox) is incorrectly zeroed-out:
mlx4_SET_PORT modifies the VL_cap field (byte 3 of the mailbox).
Since the SET_PORT command is paravirtualized on the master as well as
on the slaves, mlx4_SET_PORT_wrapper() is invoked on the master. This
calls mlx4_common_set_port() where mailbox byte 3 gets overwritten by
code which should only set a single bit in that byte (for the reset
qkey counter flag) -- but instead overwrites the entire byte.
The result is that when running in SR-IOV mode, the VL_cap will be set
to zero -- fix this.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
One sparse-warning fix, one bigfix for 3.4-stable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=VrYL
-----END PGP SIGNATURE-----
Merge tag 'md-3.5-fixes' of git://neil.brown.name/md
Pull two md fixes from NeilBrown:
"One sparse-warning fix, one bugfix for 3.4-stable"
* tag 'md-3.5-fixes' of git://neil.brown.name/md:
md: raid1/raid10: fix problem with merge_bvec_fn
lib/raid6: fix sparse warnings in recovery functions
Two patches are in here which fix AMD IOMMU specific issues. One patch
fixes a long-standing warning on resume because the amd_iommu_resume
function enabled interrupts. The other patch fixes a deadlock in an
error-path of the page-fault request handling code of the IOMMU driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=qLIK
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"Two patches are in here which fix AMD IOMMU specific issues. One
patch fixes a long-standing warning on resume because the
amd_iommu_resume function enabled interrupts. The other patch fixes a
deadlock in an error-path of the page-fault request handling code of
the IOMMU driver.
* tag 'iommu-fixes-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix deadlock in ppr-handling error path
iommu/amd: Cache pdev pointer to root-bridge
This patches fixes the driver when built as dynamic module.
In fact, the platform part cannot be built and the probe fails
(thanks to Bob Liu that reported this bug).
v2: as D. Miller suggested, it is not necessary to make the
pci and the platform code mutually exclusive.
Having both could also help, at built time ,to verify that
all the code is validated and compiles fine.
v3: removed wrong Reviewed-by from the patch
Reported-by: Bob Liu <lliubbo@gmail.com>
cc: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mmc_host is not spi mode, mmc/sd is doing mmc_deselect_cards().
mmc_deselect_cards could be returned error.
If returned error, we can know something wrong when enter suspend.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit fa550189 (mmc: core: Prevent eMMC VCC supply to be cut from late init)
slightly affected timings for how things are done for the omap MMC driver
causing the MMC cards not getting detected any longer.
Turns out this was caused by buggy reg_shift initialization in the omap
MMC driver that was happening after mmc_add_host() was being called.
Fix this by initializing reg_shift before mmc_add_host() is called.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit b01a4f1c (mmc: omap: convert to per instance workqueue) initializes
the workqueue too late causing the following:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 Not tainted (3.4.0-08218-gb48b2c3 #158)
PC is at __queue_work+0x8/0x46c
LR is at queue_work_on+0x38/0x40
pc : [<c005bb4c>] lr : [<c005c00c>] psr: 60000193
sp : c0691e1c ip : 00000000 fp : c07374ac
r10: c7aae400 r9 : c0395700 r8 : 00000100
r7 : c0691e70 r6 : 00000000 r5 : 00000000 r4 : c7aae440
r3 : 00000001 r2 : c7aae440 r1 : 00000000 r0 : 00000000
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 00c5387d Table: 80004000 DAC: 00000017
Process swapper/0 (pid: 0, stack limit = 0xc06902f8)
Stack: (0xc0691e1c to 0xc0692000)
Fix this by initializing the workqueue before mmc_omap_remove_slot()
get called. Tested on n770, looks like n800 at least still has some
other issue with MMC.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit b6e0703b (mmc: omap: make it behave well as a module) made some
__devinit changes but missed one function causing a section warning:
WARNING: vmlinux.o(.devinit.text+0x8604): Section mismatch in reference
from the function mmc_omap_probe)
The function __devinit mmc_omap_probe() references a function
__init mmc_omap_new_slot().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In case of "host->bus_hz < slot->clock", divider value is
miscalculated. And clock divider register value is multiple of 2. If
calculated divider value is odd number, result can be over-clocking.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Setting host->data to NULL is incorrect sequence in
dw_mci_command_complete. This early setting makes the skip of
dma_unmap_sg in dw_mci_dma_cleanup.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
IDMAC may not be cleaned in driver probe if it has been already used in
boot time. So IDMAC needs sw reset newly. And DMA interface reset
precedes the internal DMAC reset. Additionally SDMMC_IDMAC_SWRESET is
replaced with magic code.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
DTO interrupt can be later than transmit interrupt(IDMAC) in case of
write. Current handling of IDMAC interrupt sets EVENT_DATA_COMPLETE as
well as EVENT_XFER_COMPLETE regardless of DTO rising. This makes the
current request finish in tasklet and permits the next request even
though current data transfer is still in progress. As a result, sequence
is broken and lock-up happens. Setting EVENT_DATA_COMPLETE is not proper
after IDMAC interrupt. It should be taken after DTO interrupt is
generated.
Reported-by: Dmitry Shmidt <dimitrysh@android.com>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Hyeonsu Kim <hyeonsu.kim@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDIO_CCCR_IF[1:0] in SDIO card is used for card data bus width
setting as below:
00b: 1-bit bus
01b: Reserved
10b: 4-bit bus
11b: 8-bit bus (only for embedded SDIO)
And sdio_enable_wide is for setting data bus width as 4-bit.
But currently, it first reads the register, second OR' 1b with
SDIO_CCCR_IF[1], and then writes it back.
As we can see, this is based on such assumption that the
SDIO_CCCR_IF[0] is always 0. Apparently, this is not right.
Signed-off-by: Yong Ding <yongd@marvell.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The use of DMA slave config operation requires that the burst size
(aka chunk size) is specified through this interface.
Modify atmel-mci slave driver to use this specification on its side.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The data timeout timer was configured after mmc_add_host call. So, with bad
timings, it was possible to have a mmc request causing mod_timer call on a
non setup timer.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
3bdc9ba892 ("mmc: use really long write timeout to deal with crappy
cards") in 3.4 increased the write timeout that the core sends to host
drivers to 3 seconds. This makes sdhci's "requested timeout too large"
warning trigger on every write; so, change this pr_warning() to a DBG().
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The hardware bit IXGBE_RXD_STAT_VP appears to be set even when Rx
stripping is disabled. This results in passing frames up the stack
which do not have the 802.1Q tag stripped but have the tci bits
set as if it was.
Working around this with a check for the feature flag bit. I
would welcome any better ideas or a pointer to exactly which
bits in the hardware register need to be cleared to get the
IXGBE_RXD_STAT_VP bit to be set per data sheet.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
DCB can be used independent of if RX VLAN stripping is enabled
or disabled so remove erroneous check.
Also enable or disable VLAN stripping when features are applied so
hardware and feature flags are in sync.
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit 44abd5c127 introduced NULL pointer
dereferences when attempting to access the check_reset_block function
pointer on 8257x and 80003es2lan non-copper devices.
This fix should be applied back through 3.4.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When CONFIG_DEBUG_PREEMPT is enabled, bug is observed in the smp_processor_id().
This is because smp_processor_id() is not called in preempt safe condition.
To fix this issue, use raw_smp_processor_id instead of smp_processor_id.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
CC: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch removes a call to the deprecated simple_strtoul function
and simplifies the code by replacing two function calls with one
call to kstrtouint_from_user.
-Simplify the adv7393_write_proc function by replacing the
simple_strtoul and copy_from_user calls with one call
to kstrtouint_from_user.
-Change the count parameter from unsigned long to size_t as
this is the type that the kstrtouint_from_user function expects.
(size_t is what will be passed to the adv7393_write_proc function
by the proc write handler function proc_file_write anyway)
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
debugfs or omapdss debug support is turned off, and fixes a suspend related
crash.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yO72
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.5-rc2' of git://gitorious.org/linux-omap-dss2/linux into fbdev-for-linus
Small fixes for omapdss driver. Most importantly, fixes a build problem when
debugfs or omapdss debug support is turned off, and fixes a suspend related
crash.
Or at least plug another gapping hole. Apparrently hw desingers only
moved the bit field, but did not bother ot re-enumerate the planes
when adding support for a 3rd pipe.
Discovered by i-g-t/flip_test.
This may or may not fix the reference bugzilla, because that one
smells like we have still larger fish to fry.
v2: Fixup the impossible case to catch programming errors, noticed by
Chris Wilson.
References: https://bugs.freedesktop.org/show_bug.cgi?id=50069
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Eugeni Dodonov <eugeni.dodonov@intel.com>
Cc: stable@vger.kernel.org
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull two scsi target fixes from Nicholas Bellinger:
"The first is a small name-space collision fix from Stefan for the new
sbp-target / ieee-1394 code, and second is the FILEIO backend
conversion patch to always use O_DSYNC by default instead of O_SYNC as
recommended by hch. Note the latter is CC'ed stable."
* '3.5-merge-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/file: Use O_DSYNC by default for FILEIO backends
sbp-target: rename a variable to avoid name clash
Otherwise the LEDs stick around and cause issues the
next time around since they're still there but not
really hooked up.
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>