Before this commit sensor_hub_input_attr_get_raw_value() failed to take
the signedness of 16 and 8 bit values into account, returning e.g.
65436 instead of -100 for the z-axis reading of an accelerometer.
This commit adds a new is_signed parameter to the function and makes all
callers pass the appropriate value for this.
While at it, this commit also fixes up some neighboring lines where
statements were needlessly split over 2 lines to improve readability.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* ad9523
- sysfs write should return the number of characters used or an error, not
0 which could result in an infinite loop in userspace.
* lsm6dsx
- Fix computation of length when updating the watermark to include
timestamps avoiding the watermark being set earlier than intended.
* maxim_thermocouple
- Revert a patch adding the max31856 as it's not actually compatible with
the register set that this driver supports.
* si1133
- Fix an impossible value check so we don't always error out whether the
passed in value is good or bad.
-----BEGIN PGP SIGNATURE-----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=/Eyr
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-4.19a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.19 cycle.
* ad9523
- sysfs write should return the number of characters used or an error, not
0 which could result in an infinite loop in userspace.
* lsm6dsx
- Fix computation of length when updating the watermark to include
timestamps avoiding the watermark being set earlier than intended.
* maxim_thermocouple
- Revert a patch adding the max31856 as it's not actually compatible with
the register set that this driver supports.
* si1133
- Fix an impossible value check so we don't always error out whether the
passed in value is good or bad.
Split regmap_config.use_single_rw into use_single_read and
use_single_write. This change enables drivers of devices which only
support bulk operations in one direction to use the regmap_bulk_*()
functions for both directions and have their bulk operation split into
single operations only when necessary.
Update all struct regmap_config instances where use_single_rw==true to
instead set both use_single_read and use_single_write. No attempt was
made to evaluate whether it is possible to set only one of
use_single_read or use_single_write.
Signed-off-by: David Frey <dpfrey@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 535fba29b3.
Seems the submitter (er me, hang head in shame) didn't look at the datasheet
enough to see that the registers are quite different.
This needs to be reverted because a) would never work b) to open it be added
to a Maxim RTDs (Resistance Temperature Detectors) under development by author
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The i2c_lock_adapter name is ambiguous since it is unclear if it
refers to the root adapter or the adapter you name in the argument.
The natural interpretation is the adapter you name in the argument,
but there are historical reasons for that not being the case; it
in fact locks the root adapter. Just remove the function and force
users to spell out the I2C_LOCK_ROOT_ADAPTER name to indicate what
is really going on. Also remove i2c_unlock_adapter, of course.
This patch was generated with
git grep -l 'i2c_\(un\)\?lock_adapter' \
| xargs sed -i 's/i2c_\(un\)\?lock_adapter(\([^)]*\))/'\
'i2c_\1lock_bus(\2, I2C_LOCK_ROOT_ADAPTER)/g'
followed by white-space touch-up.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This shouldn't affect runtime at all, but Smatch complains that we
should check if mlx90632_read_ambient_raw() otherwise we
"ambient_new_raw" can be uninitialized.
drivers/iio/temperature/mlx90632.c:509 mlx90632_calc_ambient_dsp105()
error: uninitialized symbol 'ambient_new_raw'.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add GPLv2+ SPDX identifier and update email for author's drivers.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Melexis has just released Infra Red temperature sensor MLX90632 used
for contact-less temperature measurement. Driver provides basic
functionality for reporting object (and ambient) temperature with
support for object emissivity.
Signed-off-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd atomisp
cleanups (take the media tree's version).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnFrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymxbwCgtNlBkqD2JJYpLRKvI/C4w1vzZsEAnA2THRkt
g3ioPBqmqC/2DSbldr2o
=/ebw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd
atomisp cleanups (take the media tree's version)"
* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The equivalent of this is now done via macro magic when
the relevant register call is made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
MAX31856 is register equivalent to the MAX31855 but suppports J, N, R,
S, T, E and B type thermocouples in addition to K-type.
Data conversion for the various types happens transparently to the driver
via probe type detection, and a LUT on the sensor.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Crt Mori <cmo@melexis.com>
Acked-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Environmental temperature sensor is a hid defined sensor,
it measures temperature.
More information can be found in:
http://www.usb.org/developers/hidpage/HUTRR39b.pdf
According to IIO ABI definition, IIO_TEMP data output unit is
milli degrees Celsius. Add the unit convert from degree to milli degree.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Initialize the parent of the IIO device to the device that registered it.
This makes sure that the IIO device appears the right level in the device
hierarchy.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds ALERT irq and limit threshold events support for TI TMP007 - 16 bit IR thermopile sensor with integrated
math engine.
Following threshold events are supported:
1. TObj high limit
2. TObj low limit
3. TDie high limit
4. TDie low limit
Signed-off-by: Manivannan Sadhasivam <manivannanece23@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The IIO ABI specifies the name field of the IIO device as:
Description of the physical chip / device for device X.
Typically a part number.
The tmp007 driver currently uses the name of the parent device instead.
Change this to the part name to be in accordance with the ABI.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for TI TMP007 - 16 bit IR thermopile sensor with integrated Math engine.
Sensor takes care of calculating the object temperature with the help of calibrated constants stored in non-volatile memory,
thereby reducing the calculation overhead.
Signed-off-by: Manivannan Sadhasivam <manivannanece23@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This includes two branch merges for elements that may also go via MFD.
New device support
* cros_ec
- new driver to support these Chrome OS contiguous sensors which are behind
the Chrome OS embedded controller. Requires a few minor MFD and chrome
platform changes. One follow up fix deals with some dependency issues in
Kconfig.
* mpu-3050
- new driver and device tree bindings for this venerable device.
* st_accel
- support for the lng2dm an
Driver features
* ad7192
- Add DVdd regulator handling
* ad9832
- Add DVDD regulator handling
* at91
- Suspend and resume support
* si7020
- Device tree bindings
* ti-am335x
- DMA support - uses dma to accelerate short bursts of read back rather
than full blown DMA buffer support. Greatly improved performance.
Includes an MFD addition to give access to the address needed for DMA.
* tsl2583
- Device tree bindings
Cleanups and minor fixes
* ad7192
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
- Rename reg variable to reflect which regulator it is
* ad5933
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* ad7746
- Fix a missing return value (fallout from previous patch set)
* ad7780
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* ad9832
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
- Rename reg regulator to reflect which one it is
* ad9834
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* hts221
- Remove a duplicated include
* maxim thermocouple
- Handle a wrong storage side in read function. Prevent any problems that
might be introduced by additions to this driver in future.
* tsl2583 - big set from Brian Masney to drive this towards a staging
graduation.
- Convert to iio_chan_spec and read_raw / write_raw (in a couple of steps)
- Improved error handling in various functions
- Drop redundant power_state custom sysfs attribute.
- Use IIO_*_ATTR* macros for remaining attributes.
- Return an error code to userspace on invalid parameters being writen to
sysfs files.
- Add locking to various attribute accesses to remove possible races.
- Add defines for various magic numbers.
- Use smbus_read_byte_data instead of a write_byte followed by read_byte.
- Query only relevant registers in probe.
- Tidy up ordering of code comments.
- Remove a pointless power off sequence in taos_chip_on.
- Don't bother shutting down the chip when updating the lux table.
The table is held entirely in the driver and doesn't effect the chip at all.
- Drop a redundant i2c call in taos_als_calibrate where the same register
is read twice in a row.
-----BEGIN PGP SIGNATURE-----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=ptGw
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.10b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing
Jonathan writes:
Second round of new device support, cleanups and fixes for IIO in the 4.10 cycle
This includes two branch merges for elements that may also go via MFD.
New device support
* cros_ec
- new driver to support these Chrome OS contiguous sensors which are behind
the Chrome OS embedded controller. Requires a few minor MFD and chrome
platform changes. One follow up fix deals with some dependency issues in
Kconfig.
* mpu-3050
- new driver and device tree bindings for this venerable device.
* st_accel
- support for the lng2dm an
Driver features
* ad7192
- Add DVdd regulator handling
* ad9832
- Add DVDD regulator handling
* at91
- Suspend and resume support
* si7020
- Device tree bindings
* ti-am335x
- DMA support - uses dma to accelerate short bursts of read back rather
than full blown DMA buffer support. Greatly improved performance.
Includes an MFD addition to give access to the address needed for DMA.
* tsl2583
- Device tree bindings
Cleanups and minor fixes
* ad7192
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
- Rename reg variable to reflect which regulator it is
* ad5933
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* ad7746
- Fix a missing return value (fallout from previous patch set)
* ad7780
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* ad9832
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
- Rename reg regulator to reflect which one it is
* ad9834
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* hts221
- Remove a duplicated include
* maxim thermocouple
- Handle a wrong storage side in read function. Prevent any problems that
might be introduced by additions to this driver in future.
* tsl2583 - big set from Brian Masney to drive this towards a staging
graduation.
- Convert to iio_chan_spec and read_raw / write_raw (in a couple of steps)
- Improved error handling in various functions
- Drop redundant power_state custom sysfs attribute.
- Use IIO_*_ATTR* macros for remaining attributes.
- Return an error code to userspace on invalid parameters being writen to
sysfs files.
- Add locking to various attribute accesses to remove possible races.
- Add defines for various magic numbers.
- Use smbus_read_byte_data instead of a write_byte followed by read_byte.
- Query only relevant registers in probe.
- Tidy up ordering of code comments.
- Remove a pointless power off sequence in taos_chip_on.
- Don't bother shutting down the chip when updating the lux table.
The table is held entirely in the driver and doesn't effect the chip at all.
- Drop a redundant i2c call in taos_als_calibrate where the same register
is read twice in a row.
As found by gcc -Wmaybe-uninitialized, having a storage_bytes value other
than 2 or 4 will result in undefined behavior:
drivers/iio/temperature/maxim_thermocouple.c: In function 'maxim_thermocouple_read':
drivers/iio/temperature/maxim_thermocouple.c:141:5: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This probably cannot happen, but returning -EINVAL here is appropriate
and makes gcc happy and the code more robust.
Fixes: 231147ee77 ("iio: maxim_thermocouple: Align 16 bit big endian value of raw reads")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver was reporting invalid raw read values for MAX6675 on big
endian architectures. MAX6675 buffered mode is not affected, nor
is the MAX31855.
The driver was losing a 2 byte read value when it used a 32 bit
integer buffer to store a 16 bit big endian value. Use big endian
types to properly align buffers on big endian architectures.
Fixes following sparse endianness warnings:
warning: cast to restricted __be16
warning: cast to restricted __be32
Fixes checkpatch issue:
CHECK: No space is necessary after a cast
Signed-off-by: sayli karnik <karniksayli1995@gmail.com>
Fixes: 1f25ca11d8 ("iio: temperature: add support for Maxim
thermocouple chips")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fixes the following sparse warnings:
drivers/iio/temperature/maxim_thermocouple.c:35:28: warning:
symbol 'max6675_channels' was not declared. Should it be static?
drivers/iio/temperature/maxim_thermocouple.c:52:28: warning:
symbol 'max31855_channels' was not declared. Should it be static?
drivers/iio/temperature/maxim_thermocouple.c:98:38: warning:
symbol 'maxim_thermocouple_chips' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-By: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Select IIO_BUFFER and IIO_TRIGGERED_BUFFER to compile maxim_thermocouple.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add initial driver support for MAX6675, and MAX31855 thermocouple chips.
Cc: Marek Vasut <marex@denx.de>
Cc: Matt Porter <mporter@konsulko.com>
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The I2C drivers have an i2c_device_id array but that information isn't
exported to the modules using the MODULE_DEVICE_TABLE() macro. So the
modules autoloading won't work if the I2C device is registered using
OF or legacy board files due missing alias information in the modules.
The issue was found using Kieran Bingham's coccinelle semantic patch:
https://lkml.org/lkml/2016/5/10/520
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Previously most drivers that used a i2c_check_functionality() check
condition required various error codes on failure. This patchset
converts to a standard of -EOPNOTSUPP
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Support for TSYS02D temperature sensor
Signed-off-by: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Support for TSYS01 temperature sensor
Signed-off-by: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Dan Carpenter reported a static checker report and after his mail I
noticed that we actually return from function if positive value is
obtained from i2c read. This was remainder from when code was not in
separate function (which I changed during the review process).
Static checker reported
drivers/iio/temperature/mlx90614.c:167
mlx90614_iir_search()
warn: this cast is a no-op
which meant that cast before negating is useless. Dan also proposed a
solution on nicer bit operation form.
Also changed magic number to macro in process as that was confusing.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Implemented Low pass 3db frequency filter which configures
FIR and IIR values within the configuration register of EEPROM.
For more standardized interface we have fixed the FIR value
to 1024, while changes in IIR value are directly connected to
filter responses. The new datasheet version will provide a
simplified table (also in reStructured text format below) with
this change, to provide quick overview of possible settings.
Below sensor timings (bandwidth) are calculated for 3db frequency
low pass filter.
+--------------------+-----------------+
| Filter setting (%) | Band width (Hz) |
| (rounded to 1.0) | |
+====================+=================+
| 13 | 0.15 |
+--------------------+-----------------+
| 17 | 0.20 |
+--------------------+-----------------+
| 25 | 0.31 |
+--------------------+-----------------+
| 50 | 0.77 |
+--------------------+-----------------+
| 57 | 0.86 |
+--------------------+-----------------+
| 67 | 1.10 |
+--------------------+-----------------+
| 80 | 1.53 |
+--------------------+-----------------+
| 100 | 7.23 |
+--------------------+-----------------+
The diff is made towards togreg branch. Added myself to MAINTAINERS and
authors as per discussion with Jonathan.
Signed-off-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Take 2 also includes a fix set that was too late for the 4.2 cycle.
As we had a lot of tools and docs work in this set, I have broken those
out into their own categories in this description.
Fixes from the pull request '4th set of IIO fixes for the 4.2 cycle'.
* Poll functions for both event chardev and the buffer one were returning
negative error codes (via a positive value).
* A recent change to lsiio adding some error handling that was wrong and
stopped the tool working.
* bmg160 was missing some dependencies in Kconfig
* berlin2-adc had a misshandled register (wrote a value rather than a bitmap)
New device support
* TI opt3001 light sensor
* TXC PA12 ALS and proximity sensor.
* mcp3301 ADC support (in mcp320x driver)
* ST lsm303agr accelerometer and magnetometer drivers (plus some st-sensors
common support to allow different WHOAMI register addresses, devices with
fixed scale and allow interrupt equiped magnetometers).
* ADIS16305, ADIS16367, ADIS16445IMUs (in the adis16400 driver)
* ADIS16266 gyro (in the adis16260 driver)
* ADIS16137 gyro (in the adis16136 driver)
New functionality
* mmc35240 DT bindings.
* Inverse unit conversion macros to aid handing of values written to sysfs
attributes.
Core cleanup
* Forward declaration of struct iio_trigger to avoid a compile warning.
Driver cleanup / fixes
* mxs-lradc
- Clarify which parts are supported.
- Fix spelling erorrs.
- Missing/extra includes
- reorder includes
- add datasheet name listings for all usable channels (to allow them
to be bound by name from consumer drivers)
* acpi-als - add some function prefixes as per general iio style.
* bmc150_magn - replace a magic value with the existing define.
* vf610 - determine possible sample frequencies taking into account the
electrical characteristics (defining a minimum sample time)
* dht11
- whitespace
- additional docs
- avoid mulitple assignments in one line
- Use the new funciton ktime_get_resolution_ns to cleanup a nasty trick
previously used for timing.
* Fix all drivers that consider 0 a valid IRQ for historical reasons.
* Export I2C module alias info where previously missing (to allow autoprobing)
* Export OF module alias info where previously missing.
* mmc35240 - switch some variables into arrays to improve readability.
* mlx90614 - define some magic numbers for readability.
* bmc150_magn
- expand area locked by a mutex to cover all the use of the
data->buffer.
- use descriptive naming for a mask instead of a magic value.
* berin2-adc
- pass up an error code rather that a generic error
- constify the iio_chan_spec
- some other little tidy ups.
* stk8312
- fix a dependency on triggered buffers in kconfig
- add a check for invalid attribute values
- improve error handling by returning error codes where possible and
return immediately where relevant
- rework macro defs to use GENMASK etc
- change some variable types to reduce unnecessary casting
- clean up code style
- drop a local buffer copy for bulk reads and use the one in data->buffer
instead.
* adis16400 - the adis16448 gyroscope scale was wrong.
* adis16480 - some more wrong scales for various parts.
* adis16300 - has an undocumented product id and serial number registers so
use them.
* iio_simple_dummy - fix some wrong code indentation.
* bmc150-accel - use the chip ID to detect the chip present rather than
verifying the expected part was there. This was in response to a wrong
ACPI entry on the WinBook TW100.
* mma8452
- fix _get_hp_filter_index
- drop a double include
- pass up an error code rather than rewriting it
- range check input values to attribute writes
- register defs tidy up using GENMASK and reordering them to be easier to
follow.
- various coding style cleanups
- put the Kconfig entry in the write place (alphabetically).
Tools related
* Tools cleanup - drop an explicity NULL comparison, some unnecessary braces,
use the ARRAY_SIZE macro, send error messages to stderr instead of dropping
them in the middle of normal output.
* Fix tools to allow that scale and offset attributes are optional.
* More tools fixes including allowing true 32bit data (previously an overflow
prevented more than 31bits)
* Drop a stray header guard that ended up in a c file.
* Make calc_digits static as it isn't exported or in the header.
* Set ci_array pointer to NULL after free as a protection against non safe
usage of the tools core code. Also convert a double pointer to a single
one as the extra level of indirection was unnecessary.
Docs
* DocBook introduction by Daniel Baluta. Glad we are beginning to
draw together some more introductory docs to suplement the various
tools / examples.
* Drop bytes_per_datum sysfs attribute docs as it no longer exists.
* A whole load of missing / fixing of kernel-doc for the core of IIO.
* Document the trigger name sysfs attribute in the ABI docs.
* Minor typos in the ABI docs related to power down modes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJVy5EbAAoJEFSFNJnE9BaIyjEQAIXc+mjgdyMJEXLKlKKGCSY5
EX7saX91IeSK5y0CWX0hd0VPewaj4ExG7PWo3gqUSm1L9zmusLcyJm8W2pev3CGE
m7s40efxZJw0Jmmu18a3LCfcHUu/LWl4mHQtZy/AFGgWhZzWIyKA2XLqgc+Wu9qb
sjzleSJ05etDksyA7JWFCrrwBnJlW4lD25o0nD0kt3Wry2wlbN2JvZ9QLmmoc0ex
shvtI556Ew0FRywT9ir555EoJNAQQMW85Ft0dWFBnLwgc67nFTa4YNRXgoRlzhh/
sRnGKzrs5SVc1c9sxiVS4utiazxy/irHgZ5FkvTTq7F+GXeIwPK9Xv/SXZTmvs5w
lrSazRIjiLqWgpv/5oaOOGlikbpctI2kSXO0GbCW8th+l3KnKcKfComa3fnU7dca
/lofp/JzpIfwM+Bnjl1nlNuEbT0mlfJySfhUSSu/kHJxOcvDfkK4vv3oSfFp5nbF
rhA9vbVEfopXTGIOwWDjV4j0HtMCEHgOPN3T0kuyiYiWZUIjfJXchXG8e5h9/ncd
ACjH3fg6FQtHzTtzqLQky/NVAKcnFrgJSokN25GXF7R95TxufYJ6RIfnenJiCd2n
QCIdPam4bZh3/C2QYtiqWKY5e+zfkqs88/Er/HGgvxRUhKCbTvCcey1RY7FEDFHY
+9nMx/Yts8L1ulUEMjsm
=/b3G
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.3b-2' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new device support, features and cleanup for the 4.3 cycle.
Take 2 also includes a fix set that was too late for the 4.2 cycle.
As we had a lot of tools and docs work in this set, I have broken those
out into their own categories in this description.
Fixes from the pull request '4th set of IIO fixes for the 4.2 cycle'.
* Poll functions for both event chardev and the buffer one were returning
negative error codes (via a positive value).
* A recent change to lsiio adding some error handling that was wrong and
stopped the tool working.
* bmg160 was missing some dependencies in Kconfig
* berlin2-adc had a misshandled register (wrote a value rather than a bitmap)
New device support
* TI opt3001 light sensor
* TXC PA12 ALS and proximity sensor.
* mcp3301 ADC support (in mcp320x driver)
* ST lsm303agr accelerometer and magnetometer drivers (plus some st-sensors
common support to allow different WHOAMI register addresses, devices with
fixed scale and allow interrupt equiped magnetometers).
* ADIS16305, ADIS16367, ADIS16445IMUs (in the adis16400 driver)
* ADIS16266 gyro (in the adis16260 driver)
* ADIS16137 gyro (in the adis16136 driver)
New functionality
* mmc35240 DT bindings.
* Inverse unit conversion macros to aid handing of values written to sysfs
attributes.
Core cleanup
* Forward declaration of struct iio_trigger to avoid a compile warning.
Driver cleanup / fixes
* mxs-lradc
- Clarify which parts are supported.
- Fix spelling erorrs.
- Missing/extra includes
- reorder includes
- add datasheet name listings for all usable channels (to allow them
to be bound by name from consumer drivers)
* acpi-als - add some function prefixes as per general iio style.
* bmc150_magn - replace a magic value with the existing define.
* vf610 - determine possible sample frequencies taking into account the
electrical characteristics (defining a minimum sample time)
* dht11
- whitespace
- additional docs
- avoid mulitple assignments in one line
- Use the new funciton ktime_get_resolution_ns to cleanup a nasty trick
previously used for timing.
* Fix all drivers that consider 0 a valid IRQ for historical reasons.
* Export I2C module alias info where previously missing (to allow autoprobing)
* Export OF module alias info where previously missing.
* mmc35240 - switch some variables into arrays to improve readability.
* mlx90614 - define some magic numbers for readability.
* bmc150_magn
- expand area locked by a mutex to cover all the use of the
data->buffer.
- use descriptive naming for a mask instead of a magic value.
* berin2-adc
- pass up an error code rather that a generic error
- constify the iio_chan_spec
- some other little tidy ups.
* stk8312
- fix a dependency on triggered buffers in kconfig
- add a check for invalid attribute values
- improve error handling by returning error codes where possible and
return immediately where relevant
- rework macro defs to use GENMASK etc
- change some variable types to reduce unnecessary casting
- clean up code style
- drop a local buffer copy for bulk reads and use the one in data->buffer
instead.
* adis16400 - the adis16448 gyroscope scale was wrong.
* adis16480 - some more wrong scales for various parts.
* adis16300 - has an undocumented product id and serial number registers so
use them.
* iio_simple_dummy - fix some wrong code indentation.
* bmc150-accel - use the chip ID to detect the chip present rather than
verifying the expected part was there. This was in response to a wrong
ACPI entry on the WinBook TW100.
* mma8452
- fix _get_hp_filter_index
- drop a double include
- pass up an error code rather than rewriting it
- range check input values to attribute writes
- register defs tidy up using GENMASK and reordering them to be easier to
follow.
- various coding style cleanups
- put the Kconfig entry in the write place (alphabetically).
Tools related
* Tools cleanup - drop an explicity NULL comparison, some unnecessary braces,
use the ARRAY_SIZE macro, send error messages to stderr instead of dropping
them in the middle of normal output.
* Fix tools to allow that scale and offset attributes are optional.
* More tools fixes including allowing true 32bit data (previously an overflow
prevented more than 31bits)
* Drop a stray header guard that ended up in a c file.
* Make calc_digits static as it isn't exported or in the header.
* Set ci_array pointer to NULL after free as a protection against non safe
usage of the tools core code. Also convert a double pointer to a single
one as the extra level of indirection was unnecessary.
Docs
* DocBook introduction by Daniel Baluta. Glad we are beginning to
draw together some more introductory docs to suplement the various
tools / examples.
* Drop bytes_per_datum sysfs attribute docs as it no longer exists.
* A whole load of missing / fixing of kernel-doc for the core of IIO.
* Document the trigger name sysfs attribute in the ABI docs.
* Minor typos in the ABI docs related to power down modes.
Translates the magic constant numbers to named macros and add some
additional comments about their meaning.
The diff is made towards togreg branch as that branch seems to have the
most recent updates of mlx90614 driver (many are yet to be merged).
Signed-off-by: Crt Mori <cmo@melexis.com>
Acked-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Changed the offset to negative as usual equation is: (raw +
offset)*scale and in this
case offset should be negative (as we deduct 273.15 Kelvin to get temperature
in Celsius).
Signed-off-by: Crt Mori <cmo@melexis.com>
Acked-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
only SAMP_FREQ is writable
Will lead to SAMP_FREQ being written by any attempt to write
to the other exported attributes and hence a rather unexpected
result!
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
only SAMP_FREQ is writable
Will lead to SAMP_FREQ being written by any attempt to write
to the other exported attributes and hence a rather unexpected
result!
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is mostly part of an effort to clean out our current warnings
and make the autobuilder build reports more useful.
Still a worthwhile if trivial cleanup!
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Fix a typo triggering a duplicate const warning on some compilers.
Signed-off-by: Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>
Cc: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The device uses the MSB of the returned temperature value as an error
flag. Return a read error when this bit is set.
Signed-off-by: Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>
Cc: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for system sleep and runtime power management.
To wake up the device, the SDA line should be held low for at least 33ms
while SCL is high. As this is not possible using the i2c API (and not
supported by all i2c adapters), a GPIO connected to the SDA line is
needed. The GPIO is named "wakeup" and can be specified in a device
tree with the "wakeup-gpios" binding.
If the wake-up GPIO is not given, disable power management for the
device. Entering sleep requires an SMBus byte access, hence power
management is also disabled if byte access is not supported by the
adapter.
Signed-off-by: Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>
Cc: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The mapping from the 16-bit EEPROM value to the decimal 0-1 range is
approximate. A special case ensures 0xFFFF shows as 1.0 instead of
0.999998565.
Writing to EEPROM requires an explicit erase by writing zero. In
addition, it takes 20ms for the erase/write to complete. During this
time no EEPROM register should be accessed. Therefore, two msleep()s
are added to the write function and a mutex protects against concurrent
access.
Signed-off-by: Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>
Cc: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The model is detected by reading the EEPROM configuration during
probing.
Signed-off-by: Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>
Cc: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add symbols for all accessible RAM and EEPROM registers, as well as the
sleep command and timings defined in the datasheet.
Signed-off-by: Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>
Cc: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The defined registers only make sense when used for accessing RAM. Make
MLX90614_OP_RAM part of the symbol definition to avoid accidental access
to the wrong register.
Signed-off-by: Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>
Cc: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Hans de Goede