This patch handles publishing acknowledged controls through ALSA.
These controls allow user-side to send events to the firmware and
wait for the firmware to acknowledge it.
Note that although acked controls only operate in the direction
host->firmware, and therefore they are write-only as seen from user-
side code, we have to make them readable to account for all the code
out there that assumes that ALSA controls are always readable (amixer
for example.)
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for firmware controls marked SYSTEM. These are
internal to the driver-firmware interface and do not have
a user-accessible ALSA control.
Signed-off-by: Stuart Henderson <stuarth@opensource.wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch factors out converting a memory region type into
a name string, mainly so that it can be used in log commands.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the firmware has any system event signalling controls, signal
them during DSP PRE_PMD to tell the firmware it is about to be stopped.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The call to arizona_init_notifiers was only added for CODECs that are
generating voice trigger events, however, this is somewhat annoying
for machine drivers that might be used with multiple CODECs as they
need to conditionally register for the notifier, depending on the
CODEC being attached.
As the cost of initialising the notifier is so minimal, and we may
well add other events in the future that apply to more CODECs, simply
do this for all Arizona CODECs.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These functions are very thin wrappers around core functions, so they
make sense as inline functions. Also making them inline avoids build
issues in the case where the machine driver is built in but the CODEC
is built as a module.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the compressed ops run on the platform side of things we should
really access the driver data through the platform pointer rather than
the CODEC pointer. As the compressed DAIs in our systems always connect
our CODEC to our platform this has never been an issue, but should still
be corrected. Additionally it clears the way for future core refactoring
work.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: 31833ead95 ("ASoC: arizona: Move request of speaker IRQs into bus probe")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is more idiomatic to request all resources in the bus level probe,
this patch moves the request of the DSP compressed data IRQ from the
ASoC level probe into the bus level probe.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is more idiomatic to request all resources in the bus level probe,
this patch moves the request of the speaker thermal event IRQs from the
ASoC level probe into the bus level probe.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whilst ultimately we would like to move all the clocking over to the
clock framework, as an intermediate step to get people going for now
enable the source clocks for FLLs as they are powered up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whilst ultimately we would like to move all the clocking over to the
clock framework, as an intermediate step to get people going for now
gating the source clocks for SYSCLK/ASYNCCLK when they are configured
to come directly from an MCLK pin.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A good practice is to prefix the names of functions by the name
of the subsystem.
The kthread worker API is a mix of classic kthreads and workqueues. Each
worker has a dedicated kthread. It runs a generic function that process
queued works. It is implemented as part of the kthread subsystem.
This patch renames the existing kthread worker API to use
the corresponding name from the workqueues API prefixed by
kthread_:
__init_kthread_worker() -> __kthread_init_worker()
init_kthread_worker() -> kthread_init_worker()
init_kthread_work() -> kthread_init_work()
insert_kthread_work() -> kthread_insert_work()
queue_kthread_work() -> kthread_queue_work()
flush_kthread_work() -> kthread_flush_work()
flush_kthread_worker() -> kthread_flush_worker()
Note that the names of DEFINE_KTHREAD_WORK*() macros stay
as they are. It is common that the "DEFINE_" prefix has
precedence over the subsystem names.
Note that INIT() macros and init() functions use different
naming scheme. There is no good solution. There are several
reasons for this solution:
+ "init" in the function names stands for the verb "initialize"
aka "initialize worker". While "INIT" in the macro names
stands for the noun "INITIALIZER" aka "worker initializer".
+ INIT() macros are used only in DEFINE() macros
+ init() functions are used close to the other kthread()
functions. It looks much better if all the functions
use the same scheme.
+ There will be also kthread_destroy_worker() that will
be used close to kthread_cancel_work(). It is related
to the init() function. Again it looks better if all
functions use the same naming scheme.
+ there are several precedents for such init() function
names, e.g. amd_iommu_init_device(), free_area_init_node(),
jump_label_init_type(), regmap_init_mmio_clk(),
+ It is not an argument but it was inconsistent even before.
[arnd@arndb.de: fix linux-next merge conflict]
Link: http://lkml.kernel.org/r/20160908135724.1311726-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/1470754545-17632-3-git-send-email-pmladek@suse.com
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Apart from the cleanups done by Morimoto-san this has very much been a
driver focused release with very little generic change:
- A big factoring out of the simple-card code to allow it to be shared
more with the rcar generic card from Kuninori Morimoto.
- Removal of some operations duplicated on the CODEC level, again by
Kuninori Morimoto.
- Lots more machine support for x86 systems.
- New drivers for Nuvoton NAU88C10, Realtek RT5660 and RT5663.
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJX7pEPExxicm9vbmllQGtlcm5lbC5vcmcACgkQJNaLcl1Uh9Du
Fgf+MAOLDX8z7TbxAM4TnpPO7pRYF+wR+AWamVoUnHrq+gdsUkcKbnTlE8PP05Sp
VDf/ugCMcAQoYrrXPPiZLLB6YsJf2eXjlrTeF5eG/oHRC0mBeM/U6nHblNltFPKl
clV5jTm8Rq/I0AHAiYeTDetQsypK3eVjJ0PZLdenVWF+kL/+aTJ4GXIGgH27aSQC
7lwQZBRWfvGyE/IRu2NNXTPMNSaos/JtLh2/Y2qkWVEQ8YYwFxgRkfCRDHbFk2fK
8/mdWWlaBrApZN8t/RlJxo6rxuQGUn01HFvLpRK1N0EMuLWaTUFHQZtUV/KF/JSz
6Gj4tPLvDke0f4N2tIwoF9quXA==
=qgCG
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v4.9
Apart from the cleanups done by Morimoto-san this has very much been a
driver focused release with very little generic change:
- A big factoring out of the simple-card code to allow it to be shared
more with the rcar generic card from Kuninori Morimoto.
- Removal of some operations duplicated on the CODEC level, again by
Kuninori Morimoto.
- Lots more machine support for x86 systems.
- New drivers for Nuvoton NAU88C10, Realtek RT5660 and RT5663.
The recent series of changes to the caching in the SSI driver have
caused a number of problems to appear in some test systems. These are
still not fully understood but we're coming up to the merge window so
for now let's revert commit 7de2763d9b (ASoC: fsl_ssi: Remove
.num_reg_defaults_raw from regmap_config) as backing that out seems to
resolve the problem on affected systems.
Reported-by: Maciej S. Szmigiero" <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Currently there is a memory leak of module on a ENOMEM return path.
Fix this by kfree'ing module before returning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds SNDRV_PCM_TRIGGER_SUSPEND/RESUME.
Otherwise, it breaks rsnd driver internal start/stop counter
when suspend/resume. This issue was reported/tested by Hiep
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b61 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b61 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b61 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse reports a below warning.
sound/soc/codecs/da7219.c:804:57: warning: dubious: x & !y
The line includes a condition statement; '(a < b) & !c'. Practically, the
evaluated value of this statement equals to the value of '(a < b) && !c'.
Although, it's not an usual way to use bitwise operations as logical
operations to several conditions.
This commit fixes the bug.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This hardware supports only 2-channel DAI, even mono ADC digital output
has two channels with the same data.
Having min_channels=1 results in broken playback of mono files in setups
where CPU DAI supports mono.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As long as reading datasheet of STAC9766/9767, this driver includes wrong
usage of DECLARE_TLV_DB_LINEAR().
In "8.1.2. Master Volume Registers", attenuation of lineout volumes is
represented in 5 bits by -1.5 dB/step from 0 to -46.5 dB. Thus,
'master_tlv' should be dB step representation.
In "8.1.14. Record Gain", gain of volumes is represented in 4 bits by
1.5 dB/step from 0 to 22.5 dB. Thus, 'record_tlv' should be dB step
representation.
In "8.1.5. PC BEEP Volume", attenuation of volume is represented in 4 bits
by -3 dB/step from 0 to 45 dB. Thus, 'beep_tlv' should be dB step
representation.
In "8.1.7. Stereo or Mic Volume" and so on, gain of volumes is represented
in 5 bits by -1.5 dB from 12 to -34.5 dB. Thus, 'mix_tlv' should be dB
step representation.
Totally, current implementation includes misuse of TLV-related macro.
This commit replaces usage of DECLARE_TLV_DB_LINEAR() with
SNDRV_CTL_TLVD_DECLARE_DB_SCALE(), to give proper information to
applications in user land.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver has some unused variables. They should be removed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As long as reading datasheet of WM8991, this driver includes wrong usage
of DECLARE_TLV_DB_LINEAR().
In "Table 6 Input PGA Volume Range", volume is represented in 5 bits by
1.5 dB/step between -16.5/30.0 dB. Thus, 'in_pga_tlv' should be dB step
representation.
In "Table 34 LOMIX and ROMIX Volume Range", volume is represented in three
bits by -3 dB/step from 0 to -21 dB. Thus, 'out_mix_tlv' should be dB step
represenation.
In "Table 36 LOPGA, ROPGA, LOUT, ROUT and SPKVOL Volume Range", volume is
represented in 7 bits by 1 dB/step from -73 to 6 dB, including mute. Thus,
'out_pga_tlv' should be dB step representation.
In "Table 26 Digital Volume Range", volume is represented in 8 bits by
3/8 dB/step from -71.625 to 0 dB. Thus, 'out_dac_tlv' should be dB step
representation.
In "Table 16 ADC Digital Volume Range", volume is represented in 8 bits by
3/8 dB/step from -71.625 to 17.625 dB. Thus, 'in_adc_tlv' should be dB step
representation.
In "Table 23 Digital Sidetone Volume", volume is represented in 5 bits by
3 dB/step from -36 to 0 dB. Thus, 'out_sidetone_tlv' should be dB step
representation.
In "Table 12 Left Input Mixer Volume Control", volume is represented in
3 bits by 3 dB/step from -12 to 6 dB
Totally, current implementation includes misuse of TLV-related macro.
This commit replaces usage of DECLARE_TLV_DB_LINEAR() with proper macros,
to give proper information to applications in user land.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse reports a below warning.
tpa6130a2.c:193:33: warning: symbol 'tpa6130a2_component_driver' was not declared. Should it be static?
The symbol is just used inner the file. Forthermore, it's constant. Thus,
it's better to add static and const qualifier.
This commit adds it.
Fixes: cb7e62256e (ASoC: tpa6130a2: Register component)
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
Richard Fitzgerald