This patch supplements pinctl support on i.MX53.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
mx6qsabreauto is a board based on mx6q SoC with the following features:
- 2GB of DDR3
- 2 USB ports
- 1 HDMI output port
- SPI NOR
- 2 LVDS LCD ports
- Gigabit Ethernet
- Camera
- eMMC and SD card slot
- Multichannel Audio
- CAN
- SATA
- NAND
- PCIE
- Video Input
Add very basic support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
imx6q gets 5 uart ports in total. Different board design may choose
different port as debug uart. For example, imx6q-sabresd uses UART1,
imx6q-sabrelite uses UART2 and imx6q-arm2 uses UART4. Rather than
bloating DEBUG_LL choice list with all these uart ports, the patch
introduces DEBUG_IMX6Q_UART_PORT for users to input uart port number
when DEBUG_IMX6Q_UART is selected inside DEBUG_LL choice.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Setup the GPIO7_11 pin as interrupt to the DA9053 and also rename the regulator nodes
so that they match with the datasheet.
This allows probing of DA9053 to succeed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since commit 8fe4554f (leds: leds-gpio: adopt pinctrl support) gpio-led driver
has pinctrl support, so setup the gpio led pin via pinctrl and avoid the
following warning:
leds-gpio leds.2: pins are not configured from the driver
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
According to Documentation/devicetree/bindings/mmc/mmc.txt bus-width
is a mandatory property. While this is currently enforced nowhere, it's
a good habit to just add the property now to allow to add common helper
functionality for the mmc property parsing later.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
With being part of multi-platform support, SMP can be enabled by other
platform even when SOC_IMX6Q is deselected. It leads to a situation
that arch/arm/mach-imx/platsmp.c is built without HAVE_IMX_SRC selection
which will cause build error. For example, the following link errors
will be seen when building imx5 with other v7 platforms.
arch/arm/mach-imx/built-in.o: In function `imx_cpu_die':
platform-ahci-imx.c:(.text+0x219c): undefined reference to `imx_enable_cpu'
arch/arm/mach-imx/built-in.o: In function `imx_boot_secondary':
platform-ahci-imx.c:(.cpuinit.text+0x14): undefined reference to `imx_set_cpu_jump'
platform-ahci-imx.c:(.cpuinit.text+0x20): undefined reference to `imx_enable_cpu'
Select HAVE_IMX_SRC as long as SMP is enabled to fix the problem.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since commit c5a0d497(ARM: imx: enable multi-platform build),
ARCH_MXC is selected by the following logic:
config ARCH_MXC
def_bool y if ARCH_MULTI_V4_V5 || ARCH_MULTI_V6_V7
, which causes build error on vexpress_defconfig:
arch/arm/mach-imx/hotplug.c:49: undefined reference to `imx_enable_cpu'
arch/arm/mach-imx/platsmp.c:57: undefined reference to `imx_set_cpu_jump'
arch/arm/mach-imx/platsmp.c:58: undefined reference to `imx_enable_cpu'
Make ARCH_MXC a user selectable option, so that it does not get built
by default on other defconfigs that select ARCH_MULTI_V4_V5 or ARCH_MULTI_V6_V7.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It enables multi-platform build for imx. With ARCH_MULTI_* options
coming to play, ARCH_MXC becomes an user invisible option, while
ARCH_IMX_V4_V5 and ARCH_IMX_V6_V7 get removed. Both imx_v4_v5_defconfig
and imx_v6_v7_defconfig get updated to adopt the changes.
AUTO_ZRELADDR and ARM_PATCH_PHYS_VIRT are selected by ARCH_MXC now to
save the duplication.
Headers timex.h and uncompress.h are not needed for multi-platform
build. Remove them.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
mxc_device_init() is a core_initcall function used to register devices
for mxc_aips_bus and mxc_ahb_bus, which are needed by gpio and dma
device registration.
Instead of being a core_initcall function, we have it called in soc
specific initialization function before gpio and dma devices get
registered, so that it will not be called for other platforms when
we enable multi-platform support for imx.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The only mach/irqs.h user outside arch/arm/mach-imx is
sound/soc/fsl/imx-pcm-fiq.c, which refers to mxc_set_irq_fiq().
Move the declaration into include/linux/platform_data/asoc-imx-ssi.h,
so that we can remove mach/irqs.h includsion from imx-pcm-fiq.c.
Inside arch/arm/mach-imx, the only users to mach/irqs.h are avic.c
and tzic.c for referring to macro FIQ_START. Let's move the macro
into irq-common.h and get rid of mach/irqs.h completely.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: alsa-devel@alsa-project.org
It moves a bunch of header files included in hardware.h and itself
from mach-imx/include/mach to mach-imx, and updates users to include
hardware.h rather than mach/hardware.h. The files in mach-imx/devices
will need to include "../hardware.h".
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Move imx debug-macro.S over to common debug macro directory. It
removes the inclusion to hardware.h by hard-coding the physical
address of uart port and copying IMX_IO_P2V from hardware.h.
Since we will need a common solution, which might use a fixed virtual
address for uart port across platforms, we make a copy of IMX_IO_P2V
here as a temporary solution to enable low-level debug for imx
multi-platform build.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
It changes the driver to use platform_device_id rather than cpu_is_xxx
to determine the controller type, and updates the platform code
accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-fbdev@vger.kernel.org
It changes the driver to use platform_device_id rather than cpu_is_xxx
to determine the controller type, and updates the platform code
accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Chris Ball <cjb@laptop.org>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Cc: linux-mmc@vger.kernel.org
It changes the driver to use platform_device_id rather than cpu_is_xxx
to determine the controller type, and updates the platform code
accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Cc: linux-media@vger.kernel.org
It changes the driver to use platform_device_id rather than cpu_is_xxx
to determine the controller type, and updates the platform code
accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Cc: Vinod Koul <vinod.koul@linux.intel.com>
Retrieve MEM and IRQ from resources rather than directly using the
value by including machine header.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Vinod Koul <vinod.koul@linux.intel.com>
It changes the driver to use platform_device_id rather than cpu_is_xxx
to determine the controller type, and updates the platform code
accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: rtc-linux@googlegroups.com
It changes the driver to use platform_device_id rather than cpu_is_xxx
to determine the controller type, and updates the platform code
accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: linux-mtd@lists.infradead.org
This is some amount of work left/forgot from device tree conversion.
Instead of checking cpu_is_xxx to determine the controller type, the
driver should use platform_device_id, which should match the device
tree compatible string.
The patch changes the driver to use platform_device_id rather than
cpu_is_xxx to determine the controller type/version. It also updates
the platform code and device tree source accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: linux-i2c@vger.kernel.org
The header ipu.h really belongs to dma subsystem rather than imx
platform. Rename it to ipu-dma.h and put it into include/linux/dma/.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-media@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
The header mach/dma-mx1-mx2.h is used nowhere. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Rename mach-imx/include/mach/ulpi.h to mach-imx/ulpi.h, and update
users to include ulpi.h rather than mach/ulpi.h.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Rename mach-imx/include/mach/iram.h to mach-imx/iram.h, and update users
to include iram.h rather than mach/iram.h.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Rename mach-imx/include/mach/iim.h to mach-imx/iim.h, and update users
to include iim.h rather than mach/iim.h.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Rename mach-imx/include/mach/cpuidle.h to mach-imx/cpuidle.h, and
update users to include cpuidle.h rather than mach/cpuidle.h.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Rename mach-imx/include/mach/common.h to mach-imx/common.h and update
all users to include common.h rather than mach/common.h.
It also removes an unneeded inclusion to common.h in
mach-imx/devices/devices.c.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
It's really unnecessary to have plat-mxc, and let's merge it into
mach-imx. It's pretty much just a bunch of file renaming and
Kconfig/Makefile merge.
To make the change less invasive, we keep using Kconfig symbol
CONFIG_ARCH_MXC for mach-imx sub-architecture.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
It moves platform device code from plat-mxc into mach-imx. Along with
that, header devices-common.h gets moved from plat-mxc/include/mach/
into mach-imx/devices/.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
There is no need for device-imx*.h to include <soc>.h. Remove them
and fix one indirect inclusion in mach-mx31ads.c.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The board files in mach-imx are the only users of iomux drivers and
headers. Move them into mach-imx from plat-mxc.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The headers that are only used by board files do not necessarily
need to be in plat-mxc/include/mach. Move them to the same place
as those board files.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Pull MIPS update from Ralf Baechle:
"Cleanups and fixes for breakage that occured earlier during this merge
phase. Also a few patches that didn't make the first pull request.
Of those is the Alchemy work that merges code for many of the SOCs and
evaluation boards thus among other code shrinkage, reduces the number
of MIPS defconfigs by 5."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (22 commits)
MIPS: SNI: Switch RM400 serial to SCCNXP driver
MIPS: Remove unused empty_bad_pmd_table[] declaration.
MIPS: MT: Remove kspd.
MIPS: Malta: Fix section mismatch.
MIPS: asm-offset.c: Delete unused irq_cpustat_t struct offsets.
MIPS: Alchemy: Merge PB1100/1500 support into DB1000 code.
MIPS: Alchemy: merge PB1550 support into DB1550 code
MIPS: Alchemy: Single kernel for DB1200/1300/1550
MIPS: Optimize TLB refill for RI/XI configurations.
MIPS: proc: Cleanup printing of ASEs.
MIPS: Hardwire detection of DSP ASE Rev 2 for systems, as required.
MIPS: Add detection of DSP ASE Revision 2.
MIPS: Optimize pgd_init and pmd_init
MIPS: perf: Add perf functionality for BMIPS5000
MIPS: perf: Split the Kconfig option CONFIG_MIPS_MT_SMP
MIPS: perf: Remove unnecessary #ifdef
MIPS: perf: Add cpu feature bit for PCI (performance counter interrupt)
MIPS: perf: Change the "mips_perf_event" table unsupported indicator.
MIPS: Align swapper_pg_dir to 64K for better TLB Refill code.
vmlinux.lds.h: Allow architectures to add sections to the front of .bss
...
Pull module signing support from Rusty Russell:
"module signing is the highlight, but it's an all-over David Howells frenzy..."
Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.
* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
X.509: Fix indefinite length element skip error handling
X.509: Convert some printk calls to pr_devel
asymmetric keys: fix printk format warning
MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
MODSIGN: Make mrproper should remove generated files.
MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
MODSIGN: Use the same digest for the autogen key sig as for the module sig
MODSIGN: Sign modules during the build process
MODSIGN: Provide a script for generating a key ID from an X.509 cert
MODSIGN: Implement module signature checking
MODSIGN: Provide module signing public keys to the kernel
MODSIGN: Automatically generate module signing keys if missing
MODSIGN: Provide Kconfig options
MODSIGN: Provide gitignore and make clean rules for extra files
MODSIGN: Add FIPS policy
module: signature checking hook
X.509: Add a crypto key parser for binary (DER) X.509 certificates
MPILIB: Provide a function to read raw data into an MPI
X.509: Add an ASN.1 decoder
X.509: Add simple ASN.1 grammar compiler
...
The hostprogs need access to the CONFIG_* symbols found in
include/generated/autoconf.h. But commit abbf1590de ("UAPI: Partition
the header include path sets and add uapi/ header directories") replaced
$(LINUXINCLUDE) with $(USERINCLUDE) which doesn't contain the necessary
include paths.
This has the undesirable effect of breaking the EFI boot stub because
the #ifdef CONFIG_EFI_STUB code in arch/x86/boot/tools/build.c is
never compiled.
It should also be noted that because $(USERINCLUDE) isn't exported by
the top-level Makefile it's actually empty in arch/x86/boot/Makefile.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ARM update from Russell King:
"This is the final round of stuff for ARM, left until the end of the
merge window to reduce the number of conflicts. This set contains the
ARM part of David Howells UAPI changes, and a fix to the ordering of
'select' statements in ARM Kconfig files (see the appropriate commit
for why this happened - thanks to Andrew Morton for pointing out the
problem.)
I've left this as long as I dare for this window to avoid conflicts,
and I regenerated the config patch yesterday, posting it to our
mailing list for review and testing. I have several acks which
include successful test reports for it.
However, today I notice we've got new conflicts with previously unseen
code... though that conflict should be trivial (it's my changes vs a
one liner.)"
* 'late-for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: config: make sure that platforms are ordered by option string
ARM: config: sort select statements alphanumerically
UAPI: (Scripted) Disintegrate arch/arm/include/asm
Fix up fairly conflict in arch/arm/Kconfig (the select re-organization
vs recent addition of GENERIC_KERNEL_EXECVE)
The large platform selection choice should be sorted by option string
so it's easy to find the platform you're looking for. Fix the few
options which are out of this order.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As suggested by Andrew Morton:
This is a pet peeve of mine. Any time there's a long list of items
(header file inclusions, kconfig entries, array initalisers, etc) and
someone wants to add a new item, they *always* go and stick it at the
end of the list.
Guys, don't do this. Either put the new item into a randomly-chosen
position or, probably better, alphanumerically sort the list.
lets sort all our select statements alphanumerically. This commit was
created by the following perl:
while (<>) {
while (/\\\s*$/) {
$_ .= <>;
}
undef %selects if /^\s*config\s+/;
if (/^\s+select\s+(\w+).*/) {
if (defined($selects{$1})) {
if ($selects{$1} eq $_) {
print STDERR "Warning: removing duplicated $1 entry\n";
} else {
print STDERR "Error: $1 differently selected\n".
"\tOld: $selects{$1}\n".
"\tNew: $_\n";
exit 1;
}
}
$selects{$1} = $_;
next;
}
if (%selects and (/^\s*$/ or /^\s+help/ or /^\s+---help---/ or
/^endif/ or /^endchoice/)) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
undef %selects;
}
print;
}
if (%selects) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
}
It found two duplicates:
Warning: removing duplicated S5P_SETUP_MIPIPHY entry
Warning: removing duplicated HARDIRQS_SW_RESEND entry
and they are identical duplicates, hence the shrinkage in the diffstat
of two lines.
We have four testers reporting success of this change (Tony, Stephen,
Linus and Sekhar.)
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixups for some corner cases, build issues, and some obvious bugs in
IRQ handling. No major changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlB2kfsACgkQ70gcjN2673PxDQCdF7rldDDP3yCjd98/utGgdpjS
EJAAnAqIbf8oWfvMzfzo22rImXo/naio
=sO+p
-----END PGP SIGNATURE-----
Merge tag 'for-3.7' of git://openrisc.net/jonas/linux
Pull OpenRISC updates from Jonas Bonn:
"Fixups for some corner cases, build issues, and some obvious bugs in
IRQ handling. No major changes."
* tag 'for-3.7' of git://openrisc.net/jonas/linux:
openrisc: mask interrupts in irq_mask_ack function
openrisc: fix typos in comments and warnings
openrisc: PIC should act on domain-local irqs
openrisc: Make cpu_relax() invoke barrier()
audit: define AUDIT_ARCH_OPENRISC
openrisc: delay: fix handling of counter overflow
openrisc: delay: fix loops calculation for __const_udelay
Pull powerpc uapi disintegration from Benjamin Herrenschmidt.
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
UAPI: (Scripted) Disintegrate arch/powerpc/include/asm
- Do not export the COMPAT_* definitions to user
- Simplify the compat unistd32.h definitions and remove the
__SYSCALL_COMPAT guard
- Disintegrate the arch/arm64/include/asm/* headers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=1+LF
-----END PGP SIGNATURE-----
Merge tag 'arm64-uapi' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 uapi disintegration from Catalin Marinas:
"UAPI headers for arm64 together with some clean-up to make it
possible:
- Do not export the COMPAT_* definitions to user
- Simplify the compat unistd32.h definitions and remove the
__SYSCALL_COMPAT guard
- Disintegrate the arch/arm64/include/asm/* headers"
* tag 'arm64-uapi' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
UAPI: (Scripted) Disintegrate arch/arm64/include/asm
arm64: Do not export the compat-specific definitions to the user
arm64: Do not include asm/unistd32.h in asm/unistd.h
arm64: Remove unused definitions from asm/unistd32.h
Cleanups
Clean up compile warnings in kgdboc.c and x86/kernel/kgdb.c
Add module event hooks for simplified debugging with gdb
Fixes
Fix kdb to stop paging with 'q' on bta and dmesg
Fix for data that scrolls off the vga console due to line wrapping
when using the kdb pager
New
The debug core registers for kernel module events which allows a
kernel aware gdb to automatically load symbols and break on entry
to a kernel module
Allow kgdboc=kdb to setup kdb on the vga console
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=uf0L
-----END PGP SIGNATURE-----
Merge tag 'for_linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull KGDB/KDB fixes and cleanups from Jason Wessel:
"Cleanups
- Clean up compile warnings in kgdboc.c and x86/kernel/kgdb.c
- Add module event hooks for simplified debugging with gdb
Fixes
- Fix kdb to stop paging with 'q' on bta and dmesg
- Fix for data that scrolls off the vga console due to line wrapping
when using the kdb pager
New
- The debug core registers for kernel module events which allows a
kernel aware gdb to automatically load symbols and break on entry
to a kernel module
- Allow kgdboc=kdb to setup kdb on the vga console"
* tag 'for_linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
tty/console: fix warnings in drivers/tty/serial/kgdboc.c
kdb,vt_console: Fix missed data due to pager overruns
kdb: Fix dmesg/bta scroll to quit with 'q'
kgdboc: Accept either kbd or kdb to activate the vga + keyboard kdb shell
kgdb,x86: fix warning about unused variable
mips,kgdb: fix recursive page fault with CONFIG_KPROBES
kgdb: Add module event hooks
Pull Sparc updates from David Miller:
1) Updated syscall tracing fix from Al Viro.
2) SUN4V error reporting was deficient in several areas.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: fix ptrace interaction with force_successful_syscall_return()
sparc64: Fix deficiencies in sun4v error reporting.
Roland Stigge