Declare the interrupt as "one shot" so that it is masked until the end
of the threaded handler. This prevents the irq core from spitting out an
error :
"Threaded irq requested with handler=NULL and !ONESHOT for irq 63"
This was introduced by commit "usb: phy: generic: add vbus support".
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
All the gpios, ie. reset-gpios and vbus-detect-gpio, should be optional
and not prevent the driver from working. Fix the regression in the
behavior introduced by commit "usb: phy: generic: migrate to gpio_desc".
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a request from IC engineer that if we doesn't
set phypwd as 0xffffffff, we need to delay about five
32Khz cycles before set phy's pwd register, otherwise,
the wakeup signal may can't wake up controller.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
At very rare cases, the SoF will not send out after resume with
low speed connection. The workaround is do not power down
PWD.RXPWD1PT1 bit during the suspend.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For non-otg mode, we keep the usage of disconnect line between phy analog
and digital unchanging; for otg mode, at peripheral role, we keep the usage
unchanging too, at host role, the digital part needs to know dp/dm change
to respond device's data pulse when it is at low power mode.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The RLT code has already done it, so no software operation is needed.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The use of GPIOs should be optional for the generic phy, otherwise
the Altera SOCFPGA platform at least is broken.
Fixes breakage caused by a combination of e9f2cefb0c "usb: phy:
generic: migrate to gpio_desc" and 135b3c4304 "usb: dwc2: platform:
add generic PHY framework support".
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In practice failure to find phy when requested in non-OF
case means it will never become available, so
__usb_find_phy() must return -ENODEV and not -EPROBE_DEFER.
This fixes a regression caused by commit 9c9d82492b
(usb: phy: Fix deferred probing), where the USB
controller driver is left infinitely into deferred probe
when there are no phys.
Fixes: 9c9d82492b (usb: phy: Fix deferred probing)
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The final set of fixes for v3.19. Two of the fixes are
related to dwc3 scatter/gather implementation when we have
more requests queued than available TRBs, while the other
is a build fix for mv-usb PHY.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUtqoQAAoJEIaOsuA1yqRENP4QAJSfu3O8cOepIVnyIAZfnEdT
BauykTwkZj/LfH2B+6v6cacFVCSr7nuRb7bZ+dTgVykqClzCEIySqahnQEAt65u9
ergvINYZpi/t7B6DsNK7OHYyIyXKnFGmBr3R8jiHBRbJ832e/3bIZ/0pdFAmwpah
qhoGtjg0wNolF4ILXAFu3ghB/AkWBulCAwumMpldv+5p6wNzJRV72Vnto0pPpqYo
C8W6f1aXXx3C8kqv5cU60lmPT85q+CCjtaLPoCneo7KTtSqM4xQgf78M02LUNYFl
1qymKr3rWxYic6b+VEODA9y/NTBhQz0fy5JhEide6T8+eaQc+QpYSGAO+bxVK1fi
CHpdF7Yg83TAwT/HCztirqMl1TmkXc2x/NFgzY0di5NMqgDhodC+3vVtnHZPoX5S
W0g5D4QlGk0mYANx4kvijvLGBbjR/OtAv6OrK96Qvia1Vv9Nb4jrxg4PN/jbwXbR
nQ8qtU1a1AIqBYE92GIjFIiZIxFPpWzddlnRcbX1wh/1Qr2C8jsFnNQ6QwS2tyw2
HH0pVRpCLCA0oLgrCE47Y+aSHaJ5t7EsxYmb+fhi/5prOHdsggHTBQSPl526NiK+
UJ8HWm2h6sel1/JdEITT+plrn62b8UL7Vd5hYQrVewgkyDrXSIpVRYA1V1dBg40U
kEQDS7JvFdFP46IRh/Cw
=iLKs
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.19-rc6
The final set of fixes for v3.19. Two of the fixes are
related to dwc3 scatter/gather implementation when we have
more requests queued than available TRBs, while the other
is a build fix for mv-usb PHY.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The driver was recently adapted to a core API change, but the
change was incomplete, missing out the suspend helper and
leaving an extraneous local variable around:
usb/phy/phy-mv-usb.c: In function 'mv_otg_update_state':
usb/phy/phy-mv-usb.c:341:18: warning: unused variable 'phy' [-Wunused-variable]
usb/phy/phy-mv-usb.c: In function 'mv_otg_suspend':
usb/phy/phy-mv-usb.c:861:16: error: 'struct usb_phy' has no member named 'state'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: e47d92545c ("usb: move the OTG state from the USB PHY to the OTG structure")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just three fixes this time. An oops fix in ep_write() from gadgetfs,
another oops for the Atmel UDC when unloading a gadget driver and
the fix for PHY deferred probing.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUtAxnAAoJEIaOsuA1yqRErBcP/RzyenZEkuw8A6nNbGHmAi8p
eYYRPfWDdVLFyouvDcSevz2YR6PTviRfuTUu45yFlMLPQLOY00IQtwy4F+DTCB3A
Ce0QUVFTvzvXbyHteG5VaYIWvDtJQnXrhTjv8XVsvW/UXtbzCE0RWWtNGbKsvCv8
WRj/nFqymkCYhB1qqy/2b8Kdp1k8e/m1RzvaNusBaWzu73ejExme338tx6vfepQi
MSjguviCAybSgbbZbvDGfd0D1LVDnrS78gLGm/JGGU1M+mcOnv3EGY00bgnlCB9o
ydNIL+UkQTNTi6qrJQxNomwKexF9QkCrrKazMLA8lunTIt7yYuvxes01DZuLrSuN
4vXjMlyiDFjtu7tA4Fe/k1rCPwRmpKQlr2uqcMcExcSeDJ7zwsUNYsFyzDnk1JMx
nPmcuyCkP/S8QNY6w4LqcTb++cTKdH5A73nVoVHaPA5DUEAcmyMFdwm8N/R9V+PX
yvzpPwAtkLeJPkjJwt0Bg6jcJ+FfNAfnXXrIHxFYXcKnud2VmqYtSJNMhrwdbdAh
WG/jsdCtRJFAoMZzNEEPzFwQU+UW0c9ux9+jhzKFV1ognzqQALlREc5dGK2qoxDt
5yWXqD6EymsWMLKo6vuYmIzoR5WXzIdzjgSvTJQNqEafCUMBAhIRKUxq4IVoX95d
mwxe5ePPjww1tIM+8fjs
=7Fj7
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.19-rc5
Just three fixes this time. An oops fix in ep_write() from gadgetfs,
another oops for the Atmel UDC when unloading a gadget driver and
the fix for PHY deferred probing.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/phy/phy.c
Add support for vbus detection and power supply. This code is more or
less stolen from phy-gpio-vbus-usb.c, and aims at providing a detection
mechanism for VBus (ie. usb cable plug) based on a GPIO line, and a
power supply activation which draws current from the VBus.
[ balbi@ti.com : fix build break ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Change internal gpio handling from integer gpios into gpio
descriptors. This change only addresses the internal API and
device-tree/ACPI, while the legacy platform data remains integer space
based.
This change is only build compile tested, and very prone to error. I
leave this comment for now in the commit message so that this patch gets
some testing as I'm pretty sure it's buggy.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removes some functions that are not used anywhere:
fsl_otg_tick_timer() view_ulpi()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For some user cases, like plug out and replug in usb device during
the system suspend, the speed negotiation will be error due to host
doesn't know the device's disconnection, and it still hopes the
high speed device, but the device backs to "powered" state which
its high speed termination is not enabled, the usb core calls
the PHY's disconnect notifier with "full speed", it will NOT
take effect at all.
If the usb core calls disconnect notifer, the port change must happen,
so it is safe to disable high speed disconenct detector, since
connect notifier will be called soon if the device is still connected
on the port, and we will enable high speed disconnect detector at that
time.
Acked-by: Li Jun <b47624@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we shut down the PHY, we need to power down all PHY's functions
as well as disable wakeup, it is the opposite operation we do at .init.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 1290a958d4 ("usb: phy: propagate __of_usb_find_phy()'s error on
failure") actually broke the deferred probing mechanism, since it now returns
EPROBE_DEFER only when the try_module_get call fails, but not when the phy
lookup does.
All the other similar functions seem to return ENODEV when try_module_get
fails, and the error code of either __usb_find_phy or __of_usb_find_phy
otherwise.
In order to have a consistent behaviour, and a meaningful EPROBE_DEFER, always
return EPROBE_DEFER when __(of_)usb_find_phy fails to look up the requested
phy, that will be propagated by the caller, and ENODEV if try_module_get fails.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for keyword 'boolean' will be dropped later on.
No functional change.
Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Commit 1290a958d4 ("usb: phy: propagate __of_usb_find_phy()'s error on
failure") broke platforms that rely on deferred probing to order probing
of PHY and host controller drivers. The reason is that the commit simply
propagates errors from __of_usb_find_phy(), which returns -ENODEV if no
PHY has been registered yet for a given device tree node. The only case
in which -EPROBE_DEFER would now be returned is if try_module_get() did
fail, which does not make sense.
The correct thing to do is to return -EPROBE_DEFER if a PHY hasn't been
registered yet. The only condition under which it makes sense to return
-ENODEV is if the device tree node representing the PHY has been
disabled (via the status property) because in that case the PHY will
never be registered.
This patch addresses the problem by making __of_usb_find_phy() return an
appropriate error code while keeping in line with the above-mentioned
commit to propagate error codes rather than overwriting them. At the
same time the check for a valid PHY is decoupled from the check for the
try_module_get() call and a separate error code is returned if the
latter fails.
Fixes: 1290a95 (usb: phy: propagate __of_usb_find_phy()'s error on failure)
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Here's the big set of USB and PHY patches for 3.19-rc1.
The normal churn in the USB gadget area is in here, as well as xhci and
other individual USB driver updates. The PHY tree is also in here, as
there were dependancies on the USB tree.
All of these have been in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOEHcACgkQMUfUDdst+ykziQCgsm1D/af2nac6CTF2pov8VMIY
ywgAnRi8LtZ2WassrwTNxY86Avaqryis
=UVp8
-----END PGP SIGNATURE-----
Merge tag 'usb-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big set of USB and PHY patches for 3.19-rc1.
The normal churn in the USB gadget area is in here, as well as xhci
and other individual USB driver updates. The PHY tree is also in
here, as there were dependancies on the USB tree.
All of these have been in linux-next"
* tag 'usb-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (351 commits)
arm: omap3: twl: remove usb phy init data
usbip: fix error handling in stub_probe()
usb: gadget: udc: missing curly braces
USB: mos7720: delete some unneeded code
wusb: replace memset by memzero_explicit
usbip: remove unneeded structure
usb: xhci: fix comment for PORT_DEV_REMOVE
xhci: don't use the same variable for stopped and halted rings current TD
xhci: clear extra bits from slot context when setting max exit latency
xhci: cleanup finish_td function
USB: adutux: NULL dereferences on disconnect
usb: chipidea: fix platform_no_drv_owner.cocci warnings
usb: chipidea: Fixed a few typos in comments
Documentation: bindings: add doc for the USB2 ChipIdea USB driver
usb: chipidea: add a usb2 driver for ci13xxx
usb: chipidea: fix phy handling
usb: chipidea: remove duplicate dev_set_drvdata for host_start
usb: chipidea: parameter 'mode' isn't needed for hw_device_reset
usb: chipidea: add controller reset API
usb: chipidea: remove flag CI_HDRC_REQUIRE_TRANSCEIVER
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so Kconfig options
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace PM_RUNTIME with PM in Kconfig dependencies throughout the
tree.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tejun Heo <tj@kernel.org>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM (or even dropped in some cases).
Replace CONFIG_PM_RUNTIME with CONFIG_PM in the USB core code
and documentation.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When usb is connected and enumerated in device mode or when
usb is disconnected, call usb_phy_set_event() from phy drivers
to handle per-PHY event.
[ toddpoynor@google.com : Original patch in Android ]
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: Android Kernel Team <kernel-team@android.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Arve Hjønnevåg <arve@android.com>
Cc: Benoit Goby <benoit@android.com>
Cc: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Kiran Raparthy <kiran.kumar@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When __of_usb_find_phy() fails, it returns -ENODEV - its
error code has to be returned by devm_usb_get_phy_by_phandle().
Only when the former function succeeds and try_module_get()
fails should -EPROBE_DEFER be returned.
[ balbi@ti.com : remove trailing whitespace ]
Signed-off-by: Arjun Sreedharan <arjun024@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit e47d925 (usb: move the OTG state from
the USB PHY to the OTG structure) moved the
OTG state from struct usb_phy to struct usb_otg.
Unfortunately, even though I fixed quite a few
build regressions with that patch already, this
one was still missing.
Note that this driver still has other randconfig
build problems which I'll leave for driver author
to fix, as that's less trivial.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
File names in the heading comments fell out of favor long ago, and these weren't
even changed when the drivers were moved from drivers/usb/otg/, so remove them
at last...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch prepares the introduction of the generic PHY support in the
USB OTG common functions. The USB PHY member of the OTG structure is
renamed to 'usb_phy' and modifications are done in all drivers accessing
it. Renaming this pointer will allow to keep the compatibility for USB
PHY drivers.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Before using the PHY framework instead of the USB PHY one, we need to
move the OTG state into another place, since it won't be available when
USB PHY isn't used. This patch moves the OTG state into the OTG
structure, and makes all the needed modifications in the drivers
using the OTG state.
[ balbi@ti.com : fix build regressions with phy-tahvo.c, musb_dsps.c,
phy-isp1301-omap, and chipidea's debug.c ]
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sanity check on resource happening with devm_ioremap_resource().
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Reviewed-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB hub has started to use a workqueue instead of kthread. Let's update
the documentation and comments here and there.
This patch mostly just replaces "khubd" with "hub_wq". There are only few
exceptions where the whole sentence was updated. These more complicated
changes can be found in the following files:
Documentation/usb/hotplug.txt
drivers/net/usb/usbnet.c
drivers/usb/core/hcd.c
drivers/usb/host/ohci-hcd.c
drivers/usb/host/xhci.c
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUDOW+AAoJEHm+PkMAQRiGOXYH/00TPKm8PdM5cXXG2YYYv9eT
W99K7KD2i0/qiVtlGgjjvB7fO3K0HcZusTd2jmVd8IWntXvauq7Zpw5YZkjwu4KX
Y1HCwwCd2aw0FoqgrJhNP3+j5Cr1BD/HLtbffjCe+A3tppOIis4Bwt2wJOoYlXpS
hU9Jxxc4lcRo8YKbffouDo7PIneWeJy8N+WGpUR5BfJIEK0ZZtCUqn3/3WLX4FYu
fE6uiF/bACTpKXU/mo4dDbhZp439H/QdwQc9B0F8+8CBDMXKaNHrPV7kN36T2SWa
fD4boikTsi/yh9Ks1fvHbvNq2N0ihoMnja+vLRyvjAcAQv2fKG3OZtYgFWSdghU=
=Xknd
-----END PGP SIGNATURE-----
Merge tag 'v3.17-rc4' into next
Merge Linux 3.17-rc4 here so we have all the latest
fixes on next too. This also cleans up a few conflicts
when applying patches.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/gadget/Makefile
drivers/usb/gadget/function/Makefile
drivers/usb/gadget/legacy/Makefile
drivers/usb/phy/phy-samsung-usb.h
The PHY configuration is stored in an opaque "config" field, but when
allocating the structure, its proper size needs to be known. In the case
of UTMI, the proper structure is tegra_utmip_config of which a local
variable already exists, so we can use that to obtain the size from.
Fixes the following warning from the sparse checker:
drivers/usb/phy/phy-tegra-usb.c:882:17: warning: expression using sizeof(void)
Fixes: 81d5dfe6d8 (usb: phy: tegra: Read UTMIP parameters from device tree)
Cc: stable@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/phy/phy-samsung-usb[2,3] drivers got replaced by
drivers/phy/phy-samsung-usb[2,3] ones and the old common Samsung
USB PHY code is no longer used.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/phy/phy-samsung-usb3 driver got replaced by
drivers/phy/phy-samsung-usb3 one and is no longer used.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/phy/phy-samsung-usb2 driver got replaced by
drivers/phy/phy-samsung-usb2 one and is no longer used.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch makes the phy reset clk and reset line optional as this clk
is not available on boards like IFC6410 with APQ8064.
phy-reset clk is only used as argument to the mach level callbacks, so
this patch adds condition before clk_get calls so that the driver
wouldn't fail on SOCs which do not have this support.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This adds support for the USB PHY in Vybrid VF610. We assume that
the disconnection without VBUS is also needed for Vybrid.
Tests showed, without MXS_PHY_NEED_IP_FIX, enumeration of devices
behind a USB Hub fails with errors:
[ 215.163507] usb usb1-port1: cannot reset (err = -32)
[ 215.170498] usb usb1-port1: cannot reset (err = -32)
[ 215.185120] usb usb1-port1: cannot reset (err = -32)
[ 215.191345] usb usb1-port1: cannot reset (err = -32)
[ 215.202487] usb usb1-port1: cannot reset (err = -32)
[ 215.207718] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[ 215.219317] usb usb1-port1: unable to enumerate USB device
Hence we also enable the MXS_PHY_NEED_IP_FIX flag.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove unnecessary lines of register bit definitions in order
to enhance the readability. In this case, there are lines
per register offset definitions. There is no functional change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case of error, the function devm_ioremap_nocache() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the datasheet, PHYPARAM1_PCS_TXDEEMPH is set as
6 bits [5:0]. Thus, the bit mask should be set as 0x3f, instead
of 0x1f.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using kfree to free data allocated with devm_kzalloc causes double frees.
The Coccinelle semantic patch that fixes this problem is as follows:
// <smpl>
@@
expression x;
@@
x = devm_kzalloc(...)
...
?-kfree(x);
// </smpl>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When __usb_find_phy_dev() does not return error and
try_module_get() fails, return -ENODEV.
Signed-off-by: Arjun Sreedharan <arjun024@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull trivial tree changes from Jiri Kosina:
"Summer edition of trivial tree updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: fix two typos in watchdog-api.txt
irq-gic: remove file name from heading comment
MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
scsi: mvsas: mv_sas.c: Fix for possible null pointer dereference
doc: replace "practise" with "practice" in Documentation
befs: remove check for CONFIG_BEFS_RW
scsi: doc: fix 'SCSI_NCR_SETUP_MASTER_PARITY'
drivers/usb/phy/phy.c: remove a leading space
mfd: fix comment
cpuidle: fix comment
doc: hpfall.c: fix missing null-terminate after strncpy call
usb: doc: hotplug.txt code typos
kbuild: fix comment in Makefile.modinst
SH: add proper prompt to SH_MAGIC_PANEL_R2_VERSION
ARM: msm: Remove MSM_SCM
crypto: Remove MPILIB_EXTRA
doc: CN: remove dead link, kerneltrap.org no longer works
media: update reference, kerneltrap.org no longer works
hexagon: update reference, kerneltrap.org no longer works
doc: LSM: update reference, kerneltrap.org no longer works
...
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aJY4
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.17 merge window
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Use SIMPLE_DEV_PM_OPS macro and remove DEV_PM_OPS macro, in order
to make the code simpler.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is no longer needed and keeping it will break 64-bit ARM builds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
tegra_usb_phy_close() is supposed to undo the effects of
tegra_usb_phy_init(). It is also currently added as the USB PHY shutdown
callback, which is wrong, since tegra_usb_phy_init() is only called
during probing wheras the shutdown callback can get called multiple
times. This then leads to warnings about unbalanced regulator_disable if
the EHCI driver is unbound and bound again at runtime.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is no longer needed and keeping it will break 64-bit ARM builds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use case is when the phy is configured in host mode and a usb device is
attached to board before bootup. On bootup, with the existing code and
runtime pm enabled, the driver would decrement the pm usage count
without checking the current state of the phy. This pm usage count
decrement would trigger the runtime pm which than would abort the
usb enumeration which was in progress. In my case a usb stick gets
detected and then immediatly the driver goes to low power mode which is
not correct.
log:
[ 1.631412] msm_hsusb_host 12520000.usb: EHCI Host Controller
[ 1.636556] msm_hsusb_host 12520000.usb: new USB bus registered, assigned bus number 1
[ 1.642563] msm_hsusb_host 12520000.usb: irq 220, io mem 0x12520000
[ 1.658197] msm_hsusb_host 12520000.usb: USB 2.0 started, EHCI 1.00
[ 1.659473] hub 1-0:1.0: USB hub found
[ 1.663415] hub 1-0:1.0: 1 port detected
...
[ 1.973352] usb 1-1: new high-speed USB device number 2 using msm_hsusb_host
[ 2.107707] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 2.108993] scsi0 : usb-storage 1-1:1.0
[ 2.678341] msm_otg 12520000.phy: USB in low power mode
[ 3.168977] usb 1-1: USB disconnect, device number 2
This issue was detected on IFC6410 board.
This patch fixes the intial runtime pm trigger by checking the phy
state and decrementing the pm use count only when the phy state is IDLE.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch makes the phy reset clk and reset line optional as this clk
is not available on boards like IFC6410 with APQ8064.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The various devm_ functions allocate memory that is released when a
driver detaches. This patch uses devm_kzalloc, devm_request_irq,
devm_gpio_request, devm_regulator_get etc. for data that is
allocated in the probe function of a platform device and is only
freed in the remove function. The corresponding free functions are
removed and the labels are done away with.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here is the big USB driver pull request for 3.16-rc1.
Nothing huge here, but lots of little things in the USB core, and in
lots of drivers. Hopefully the USB power management will be work better
now that it has been reworked to do per-port power control dynamically.
There's also a raft of gadget driver updates and fixes, CONFIG_USB_DEBUG
is finally gone now that everything has been converted over to the
dynamic debug inteface, the last hold-out drivers were cleaned up and
the config option removed. There were also other minor things all
through the drivers/usb/ tree, the shortlog shows this pretty well.
All have been in linux-next, including the very last patch, which came
from linux-next to fix a build issue on some platforms.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlONYEMACgkQMUfUDdst+ynxvgCggMQBhN5icth8Y5hFglNNaISN
c4AAoMHR2kb62U1plylLbPnboQTjfcl0
=fG6y
-----END PGP SIGNATURE-----
Merge tag 'usb-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb into next
Pull USB driver updates from Greg KH:
"Here is the big USB driver pull request for 3.16-rc1.
Nothing huge here, but lots of little things in the USB core, and in
lots of drivers. Hopefully the USB power management will be work
better now that it has been reworked to do per-port power control
dynamically. There's also a raft of gadget driver updates and fixes,
CONFIG_USB_DEBUG is finally gone now that everything has been
converted over to the dynamic debug inteface, the last hold-out
drivers were cleaned up and the config option removed. There were
also other minor things all through the drivers/usb/ tree, the
shortlog shows this pretty well.
All have been in linux-next, including the very last patch, which came
from linux-next to fix a build issue on some platforms"
* tag 'usb-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (314 commits)
usb: hub_handle_remote_wakeup() only exists for CONFIG_PM=y
USB: orinoco_usb: remove CONFIG_USB_DEBUG support
USB: media: lirc: igorplugusb: remove CONFIG_USB_DEBUG support
USB: media: streamzap: remove CONFIG_USB_DEBUG
USB: media: redrat3: remove CONFIG_USB_DEBUG usage
USB: media: redrat3: remove unneeded tracing macro
usb: qcserial: add additional Sierra Wireless QMI devices
usb: host: max3421-hcd: Use module_spi_driver
usb: host: max3421-hcd: Allow platform-data to specify Vbus polarity
usb: host: max3421-hcd: fix "spi_rd8" uses dynamic stack allocation warning
usb: host: max3421-hcd: Fix missing unlock in max3421_urb_enqueue()
usb: qcserial: add Netgear AirCard 341U
Documentation: dt-bindings: update xhci-platform DT binding for R-Car H2 and M2
usb: host: xhci-plat: add xhci_plat_start()
usb: host: max3421-hcd: Fix potential NULL urb dereference
Revert "usb: gadget: net2280: Add support for PLX USB338X"
USB: usbip: remove CONFIG_USB_DEBUG reference
USB: remove CONFIG_USB_DEBUG from defconfig files
usb: resume child device when port is powered on
usb: hub_handle_remote_wakeup() depends on CONFIG_PM_RUNTIME=y
...
The bulk of this branch is updates for Renesas Shmobile. They are still
doing some enablement for classic boards first, and then come up with DT
bindings when they've had a chance to learn more about the hardware. Not
necessarily a bad way to go about it, and they're looking at moving some
of the temporary board code resulting from it to drivers/staging instead
to avoid the churn here.
As a result of the shmobile clock cleanups, we end up merging quite a
bit of SH code here as well. We ended up merging it here instead of in
the cleanup branch due to the other board changes depending on it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=lWof
-----END PGP SIGNATURE-----
Merge tag 'boards-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC board support updates from Olof Johansson:
"The bulk of this branch is updates for Renesas Shmobile. They are
still doing some enablement for classic boards first, and then come up
with DT bindings when they've had a chance to learn more about the
hardware. Not necessarily a bad way to go about it, and they're
looking at moving some of the temporary board code resulting from it
to drivers/staging instead to avoid the churn here.
As a result of the shmobile clock cleanups, we end up merging quite a
bit of SH code here as well. We ended up merging it here instead of
in the cleanup branch due to the other board changes depending on it"
* tag 'boards-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (130 commits)
ARM: davinci: remove checks for CONFIG_USB_MUSB_PERIPHERAL
ARM: add drivers for Colibri T30 to multi_v7_defconfig
ARM: shmobile: Remove Genmai reference DTS
ARM: shmobile: Let Genmai multiplatform boot with Genmai DTB
ARM: shmobile: Sync Genmai DTS with Genmai reference DTS
ARM: shmobile: genmai-reference: Remove legacy clock support
ARM: shmobile: Remove non-multiplatform Genmai reference support
ARM: configs: enable XHCI mvebu support in multi_v7_defconfig
ARM: OMAP: replace checks for CONFIG_USB_GADGET_OMAP
ARM: OMAP: AM3517EVM: remove check for CONFIG_PANEL_SHARP_LQ043T1DG01
ARM: OMAP: SX1: remove check for CONFIG_SX1_OLD_FLASH
ARM: OMAP: remove some dead code
ARM: OMAP: omap3stalker: remove two Kconfig macros
ARM: tegra: tegra_defconfig updates
ARM: shmobile: r7s72100: use workaround for non DT-clocks
ARM: shmobile: Add forward declaration of struct clk to silence warning
ARM: shmobile: r7s72100: remove SPI DT clocks from legacy clock support
ARM: shmobile: r7s72100: add spi clocks to dtsi
ARM: shmobile: r7s72100: remove I2C DT clocks from legacy clock support
ARM: shmobile: r7s72100: add i2c clocks to dtsi
...
Since usb otg fsm implementation is not related to usb phy.
We move it from usb/phy/ to usb/common/, and rename it to
reflect its real meaning.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Renesas R-Car USB PHY driver only supports the R8A7778 and
R8A7779, it isn't useful on other systems unless build testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My previous patch introduced a bug which prevented this driver from
loading. devm_ioremap_resource() has a call to
devm_request_mem_region() which will fail because the address space is
shared between this PHY driver and CI device controller driver.
Fixes: 10f0577aa5 ('usb: phy: msm: change devm_ioremap() to devm_ioremap_resource()')
Reported-by:"Ivan T. Ivanov" <iivanov@mm-sol.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not a lot here during this merge window. Mostly we just have
the usual miscellaneous patches (removal of unnecessary prints,
proper dependencies being added to Kconfig, build warning fixes,
new device ID, etc.
Other than those, the only important new features are the
new support for OS Strings which should help Linux Gadget
Drivers behave better under MS Windows. Also Babble Recovery
implementation for MUSB on AM335x. Lastly, we also have
ARCH_QCOM PHY support though phy-msm.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Q1jA
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.16 merge window
Not a lot here during this merge window. Mostly we just have
the usual miscellaneous patches (removal of unnecessary prints,
proper dependencies being added to Kconfig, build warning fixes,
new device ID, etc.
Other than those, the only important new features are the
new support for OS Strings which should help Linux Gadget
Drivers behave better under MS Windows. Also Babble Recovery
implementation for MUSB on AM335x. Lastly, we also have
ARCH_QCOM PHY support though phy-msm.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/phy/phy-mv-u3d-usb.c
Commit 193ab2a607 ("usb: gadget: allow multiple gadgets to be built")
apparently required that checks for CONFIG_USB_GADGET_OMAP would be
replaced with checks for CONFIG_USB_OMAP. Do so now for the remaining
checks for CONFIG_USB_GADGET_OMAP, even though these checks have
basically been broken since v3.1.
And, since we're touching this code, use the IS_ENABLED() macro, so
things will now (hopefully) also work if USB_OMAP is modular.
Fixes: 193ab2a607 ("usb: gadget: allow multiple gadgets to be built")
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
adding new device id for SMSC USB334x devices.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are several issues here:
1) platform_get_resource() can return NULL and that wasn't handled.
2) We should request the memory before we remap it, and
devm_ioremap_resource() does that.
3) devm_ioremap() returns a NULL but we were checking for IS_ERR().
Fixes: 6b99c68ec1 ('usb: phy: msm: Migrate to Managed Device Resource allocation')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit a273454341 "usb: phy: msm: Use reset framework for LINK
and PHY resets" introduced a mandatory call to reset_control_get
into the msm usb phy driver, which means we have to add a Kconfig
dependency on the API to avoid this build error:
phy/phy-msm-usb.c: In function 'msm_otg_read_dt':
phy/phy-msm-usb.c:1461:2: error: implicit declaration of function 'devm_reset_control_get' [-Werror=implicit-function-declaration]
motg->link_rst = devm_reset_control_get(&pdev->dev, "link");
^
Since the usb-ehci-msm driver currently selects the OTG driver,
we could still get a broken dependency here. To solve that,
this patch also removes the 'select', which turns out to be
unnecessary.
Reviewed-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
By adding COMPILE_TEST to the list of dependencies
we can build test this driver on all other architectures
which is very valuable for maintainers applying patches
and to find silly mistakes during development.
Reviewed-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove that single instance of writel_relaxed()
call which is only available on ARM architecture.
This will let us build test this driver on all
different architectures.
Reviewed-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this solves the following build warning found when
running compile tests.
drivers/usb/phy/phy-msm-usb.c: In function ‘msm_otg_read_dt’:
drivers/usb/phy/phy-msm-usb.c:1459:20: warning: cast from pointer \
to integer of different size [-Wpointer-to-int-cast]
pdata->phy_type = (int) id->data;
^
Signed-off-by: Felipe Balbi <balbi@ti.com>
There could be more than one USB2.0 PHY's on the platform.
This will allow all of them to be registered successfully.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
New platform uses RBCPR hardware feature, with that voting for
absolute voltage of VDD CX is not required. Hence vote for corner of
VDD CX which uses nominal corner voltage on VDD CX.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Cc: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Put the transceiver in non-driving mode. Otherwise host
may not detect soft-disconnection.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Cc: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Select the secondary PHY using the TCSR register, if phy-num=1
in the DTS (or phy_number is set in the platform data). The
SOC has 2 PHYs which can be used with the OTG port, and this
code allows configuring the correct one.
Note: This resolves the problem I was seeing where I couldn't
get the USB driver working at all on a dragonboard, from cold
boot. This patch depends on patch 5/14 from Ivan's msm USB
patch set. It does not use DT for the register address, as
there's no evidence that this address changes between SoC
versions.
Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the value used for Parallel Transceiver Select (PTS) for the MSM USB
controller. This is a standard chipidea PORTSC definition, where
a PHY_TYPE of 10b (<<30) is ULPI and 11b (<<30) is SERIAL.
Fix the definitions and use them correctly in the driver code.
Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On few legacy platforms, USB PHY is having dedicated reset clk.
It is used to reset USB PHY after putting USB PHY into low power
mode and for calibration of USB PHY. Putting USB PHY into low
power mode is causing ulpi read/write timeout as expected. USB PHY
reset clk is not available on newer platform.
For 28nm PHY, reset USB PHY after resetting USB LINK.
Also reset USB PHY using USB_PHY_PON bit with USB_OTG_HS_PHY_CTRL
register after programming USB PHY Override registers as suggested
with hardware programming guidelines.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Cc: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allow support to use 2nd HSPHY with USB2 Core.
Some platforms may have configuration to allow USB controller
work with any of the two HSPHYs present. By default driver
configures USB core to use primary HSPHY. Add support to allow
user select 2nd HSPHY using DT parameter.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Cc: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using reset framework eliminate need of platform specific
callbacks and enable reset lines to be specified in DT files.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Prefix did not bring any useful information. Currently none
of the MSM platforms define these regulators, so it is safe
to rename them.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no references to 'pclk_src_name' in plaform code,
so it is unused.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use enum usb_dr_mode and drop default usb_dr_mode from platform data.
USB DT bindings states: dr_mode: "...In case this attribute isn't
passed via DT, USB DRD controllers should default to OTG...",
so remove redundand field.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This fixes following:
WARNING: quoted string split across lines
WARNING: Prefer seq_puts to seq_printf
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Whether regulators are available or not is checked at driver
probe. If they are not available driver will refuse to load,
so no need to check them again.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move memory, regulators, clocks and irq allocation to
devm_* variants. Properly check for valid clk handles.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using platform_driver_probe() prevent driver from requesting
probe deferral. Fix this.
While at that, also switch to module_platform_driver() and
remove __init annotation from probe().
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Eliminating global variables allows driver to handle multiple
device instances.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Controller could be found on APQ and MSM platforms,
make configuration description more generic.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The usb phy driver for mv_u3d got added in v3.7 through commit
a67e76ac90 ("usb: phy: mv_u3d: Add usb phy driver for mv_u3d"). It
then depended on USB_MV_U3D. And that symbol depended
on CPU_MMP3 at that time. But CPU_MMP3 has never been part of the tree.
This means that this drive was unbuildable when it was added.
In commit 60630c2eab ("usb: gadget: mv_u3d: drop ARCH dependency")
MV_U3D_PHY was made depended directly on CPU_MMP3. That kept it
unbuildable, of course.
Remove this driver. It can be re-added once its dependencies are part of
the tree.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch exports symbol of otg_statemachine for kernel module
can use it.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to:"On-The-Go and Embedded Host Supplement to the USB Revision 2.0
Specification July 27, 2012 Revision 2.0 version 1.1a"
- add a_wait_vrise to a_wait_vfall
- update condition from a_wait_vrise to a_wait_bcon
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
it's now very easy to return a platform_device pointer
and have the caller pass it as argument when calling
usb_phy_generic_unregister().
Signed-off-by: Felipe Balbi <balbi@ti.com>
no functional changes, just renaming the function
in order to make it slightly clearer what it should
be used for, also matching the driver name.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We only support GPL drivers in the USB Gadget Framework,
it sounds correct to make all exported symbols GPL too.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Tests have shown that when a power-up transition is followed by other
PHY operations too quickly, the USB port appears dead. Waiting 1ms fixes
this problem.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: stable@vger.kernel.org [3.14]
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case we found a matching USB PHY in usb_get_phy() but the call to
try_module_get() fails, we shouldn't return a (probably soon dangling)
pointer but an ERR_PTR instead.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add new ulpi IDs which are available on Xilinx Zynq boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
and a multi-purpose PHY in APM, all adapted to generic PHY framework.
Adapted USB3 PHY driver in OMAP to generic PHY driver and also used
the same driver for SATA in OMAP. It also includes miscellaneous cleanups
and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=mpZ3
-----END PGP SIGNATURE-----
Merge tag 'for_3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
Add new PHY drivers for SATA and USB in exynos, for USB in sunxi,
and a multi-purpose PHY in APM, all adapted to generic PHY framework.
Adapted USB3 PHY driver in OMAP to generic PHY driver and also used
the same driver for SATA in OMAP. It also includes miscellaneous cleanups
and fixes.
Rename struct omap_control_usb to struct omap_control_phy since it can
be used to control PHY of USB, SATA and PCIE. Also move the driver and
include files under *phy* and made the corresponding changes in the users
of phy-omap-control.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
another substantial pull request with new features all over
the place.
dwc3 got a bit closer towards hibernation support with after
a few patches re-factoring code to be reused for hibernation.
Also in dwc3 two new workarounds for known silicon bugs have
been implemented, some randconfig build errors have been fixed,
and it was taught about the new generic phy layer.
MUSB on AM335x now supports isochronous transfers thanks to
George Cherian's work.
The atmel_usba driver got two crash fixes: one when no endpoint
was specified in DeviceTree data and another when stopping the UDC
in DEBUG builds.
Function FS got a much needed fix to ffs_epfile_io() which was
copying too much data to userspace in some cases.
The printer gadget got a fix for a possible deadlock and plugged
a memory leak.
Ethernet drivers now use NAPI for RX which gives improved throughput.
Other than that, the usual miscelaneous fixes, cleanups, and
the like.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AAie
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.15
another substantial pull request with new features all over
the place.
dwc3 got a bit closer towards hibernation support with after
a few patches re-factoring code to be reused for hibernation.
Also in dwc3 two new workarounds for known silicon bugs have
been implemented, some randconfig build errors have been fixed,
and it was taught about the new generic phy layer.
MUSB on AM335x now supports isochronous transfers thanks to
George Cherian's work.
The atmel_usba driver got two crash fixes: one when no endpoint
was specified in DeviceTree data and another when stopping the UDC
in DEBUG builds.
Function FS got a much needed fix to ffs_epfile_io() which was
copying too much data to userspace in some cases.
The printer gadget got a fix for a possible deadlock and plugged
a memory leak.
Ethernet drivers now use NAPI for RX which gives improved throughput.
Other than that, the usual miscelaneous fixes, cleanups, and
the like.
Signed-of-by: Felipe Balbi <balbi@ti.com>
No functional change. Moved omap_usb.h from linux/usb/ to linux/phy/.
Also removed the unused members of struct omap_usb (after phy-omap-pipe3
started using it's own header file)
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
According to:"On-The-Go and Embedded Host Supplement to the USB Revision 2.0
Specification July 27, 2012 Revision 2.0 version 1.1a"
- From a_host to a_wait_bcon if !b_conn
- Add transition from a_host to a_wait_vfall if id state is high or a_bus_drop
- From a_wait_vfall to a_idle if a_wait_vfall_tmout
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adapted omap-usb3 PHY driver to Generic PHY Framework and moved phy-omap-usb3
driver in drivers/usb/phy to drivers/phy and also renamed the file to
phy-ti-pipe3 since this same driver will be used for SATA PHY and
PCIE PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
After clear portsc.phcd, PHY needs 200us stable time for switch
32K clock to AHB clock.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need this to keep PHY's power on or off during the system
suspend mode. If we need to enable USB wakeup, then we
must keep PHY's power being on during the system suspend mode.
Otherwise, we need to keep PHY's power being off to save power.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we need the PHY can be waken up by external signals,
we can call this API. Besides, we call mxs_phy_disconnect_line
at this API to close the connection between USB PHY and
controller, after that, the line state from controller is SE0.
Once the PHY is out of power, without calling mxs_phy_disconnect_line,
there are unknown wakeups due to dp/dm floating at device mode.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is used to access un-regulator registers according to
different controllers.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Two PHY bugs are fixed by IC logic, but these bits are not
enabled by default, so we enable them at driver.
The two bugs are: MXS_PHY_ABNORMAL_IN_SUSPEND and MXS_PHY_SENDING_SOF_TOO_FAST
which are described at code.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Change "high speed" to "HS"
Change "non-high speed" to "FS/LS"
Implementation of notify_suspend and notify_resume will be different
according to mxs_phy_data->flags.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is needed by imx6 SoC series, but not for imx23 and imx28.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The auto setting is used to open related power and clocks
automatically after receiving wakeup signal.
With this feature, the PHY's clock and power can be recovered
correctly from low power mode, it is guaranteed by IC logic.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The mxs-phy has several bugs and features at different
versions, the driver code can get it through of_device_id.data.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The probe() method has the 'dev' local variable declared and used but strangely
not in all cases where it should be...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Both the PM_RUNTIME and PM_SLEEP callbacks call into the common
msm_otg_{suspend,resume} routines, however these routines are only being
built when CONFIG_PM_SLEEP. In addition, msm_otg_{suspend,resume} also
depends on msm_hsusb_config_vddcx(), which is only built when
CONFIG_PM_SLEEP.
Fix the CONFIG_PM_RUNTIME, !CONFIG_PM_SLEEP case by changing the
preprocessor conditional, and moving msm_hsusb_config_vddcx().
While we're here, eliminate the CONFIG_PM conditional for setting
up the dev_pm_ops.
This address the following errors Russell King has hit doing randconfig
builds:
drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_suspend':
drivers/usb/phy/phy-msm-usb.c:1691:2: error: implicit declaration of function 'msm_otg_suspend'
drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_resume':
drivers/usb/phy/phy-msm-usb.c:1699:2: error: implicit declaration of function 'msm_otg_resume'
Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Free "motog" on error. This is more to appease the static checkers than
a real worry.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the PHY layer is supposed to be optional,
considering some PHY have no control bus
for SW to poke around.
After commit 1ae5799 (usb: hcd: Initialize
USB phy if needed) any HCD which didn't provide
a PHY driver would emit annoying error messages.
In this patch we're decreasing those messages
to debugging only and we also add a PHY prefix
or use dev_dbg so we know where they're coming from.
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Updates of SoC-near drivers and other driver updates that makes more sense to
take through our tree.
The largest part of this is a conversion of device registration for some
renesas shmobile/sh devices over to use resources. This has required
coordination with the corresponding arch/sh changes, and we've agreed
to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure firmware,
which is what is used on many of the commercial Nvidia Tegra products
that are in the market, including the Nvidia Shield. The code is local
to arch/arm at this time since it's uncertain whether it will be shared
with arm64 longer-term, if needed we will refactor later.
A couple of new RTC drivers used on ARM boards, merged through our tree
on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JJlw
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree.
The largest part of this is a conversion of device registration for
some renesas shmobile/sh devices over to use resources. This has
required coordination with the corresponding arch/sh changes, and
we've agreed to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure
firmware, which is what is used on many of the commercial Nvidia Tegra
products that are in the market, including the Nvidia Shield. The
code is local to arch/arm at this time since it's uncertain whether it
will be shared with arm64 longer-term, if needed we will refactor
later.
A couple of new RTC drivers used on ARM boards, merged through our
tree on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
watchdog: davinci: rename platform driver to davinci-wdt
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
...
* qcom/drivers:
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch fix compilation error when driver is compiled
in multi-platform builds.
drivers/built-in.o: In function `msm_otg_link_clk_reset':
./drivers/usb/phy/phy-msm-usb.c:314: undefined reference to `clk_reset'
./drivers/usb/phy/phy-msm-usb.c:318: undefined reference to `clk_reset'
Use platform data supplied reset handlers and adjust error
messages reported when reset sequence fail.
This is an intermediate step before adding support for reset
framework and newer targets.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pull request is quite extensive, containing
105 non-merge commits. Because of that, we describe
the changes in sections below:
New drivers:
- Keystone PHY driver and DWC3 Glue Layer
- Aeroflex Gaisler GRUSBDC
- Tahvo PHY driver for N770
- JZ4740 MUSB gluer Layer
- Broadcom PHY Driver
Important new features:
- MUSB DSPS learned about suspend/resume
- New quirk_ep_out_aligned_size flag added to struct usb_gadget
- DWC3 initializes the new quirk flag so gadget drivers can use it.
- AM335x PHY Driver learns about remote wakeup
- Renesas USBHS now requests DMA Engine only once
- s3c-hsotg is now re-used on Broadcom devices
- USB PHY layer now makes sure to initialize the notifier for all
drivers
- omap-control learned about TI's new AM437x devices
- few other usb gadget/function drivers learned about the new
configfs-based binding.
Misc Fixes and Clean Ups:
- Several sparse fixes all over the place
- Removal of redundant of_match_ptr()
- r-car gen2 phy now uses usb_add_phy_dev()
- removal of DEFINE_PCI_DEVICE_TABLE() from a few drivers
- conversion to clk_prepare/clk_unprepare on r8a66597-udc
- some randconfig errors and build warnings were fixed
- removal of unnecessary lock on dwc3-omap.c
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=N4//
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v3.14 merge window
This pull request is quite extensive, containing
105 non-merge commits. Because of that, we describe
the changes in sections below:
New drivers:
- Keystone PHY driver and DWC3 Glue Layer
- Aeroflex Gaisler GRUSBDC
- Tahvo PHY driver for N770
- JZ4740 MUSB gluer Layer
- Broadcom PHY Driver
Important new features:
- MUSB DSPS learned about suspend/resume
- New quirk_ep_out_aligned_size flag added to struct usb_gadget
- DWC3 initializes the new quirk flag so gadget drivers can use it.
- AM335x PHY Driver learns about remote wakeup
- Renesas USBHS now requests DMA Engine only once
- s3c-hsotg is now re-used on Broadcom devices
- USB PHY layer now makes sure to initialize the notifier for all
drivers
- omap-control learned about TI's new AM437x devices
- few other usb gadget/function drivers learned about the new
configfs-based binding.
Misc Fixes and Clean Ups:
- Several sparse fixes all over the place
- Removal of redundant of_match_ptr()
- r-car gen2 phy now uses usb_add_phy_dev()
- removal of DEFINE_PCI_DEVICE_TABLE() from a few drivers
- conversion to clk_prepare/clk_unprepare on r8a66597-udc
- some randconfig errors and build warnings were fixed
- removal of unnecessary lock on dwc3-omap.c
Signed-of-by: Felipe Balbi <balbi@ti.com>
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSt1TYAAoJEHm+PkMAQRiGvWgH/iWg8TmEWz4KUKuHthuUi0uh
9+2YDN+4k577Xa0obaG24giQeqkCdxMr3oJrS3FO9jeAmaNRHEGhxUPneisb7RtN
9jIVsz5bPa9/DcK9nqtaUQdvA0O5AWTE6AAPmwleTVy+8CygBo987T2uGELnQCSR
FrKCrMePc7Pj0uthMVXrpJ17Ffm/j7jkfRtPhrxHJyngh3jEux+tPbpynH/aKuO2
47unsSQimoFk7n2SPFvNu3E/vZE2xVbu5SH9MCl5yyiCifFjpi3B71LV/FW51lvm
cK8Jzn2BmYDygRFjnZfq4zJHqYJCBHzpjCLWmR37Dm/JS91aGq3+Cg0stDP8UTs=
=+Hcn
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc5' into next
Linux 3.13-rc5
* tag 'v3.13-rc5': (231 commits)
Linux 3.13-rc5
aio: clean up and fix aio_setup_ring page mapping
aio/migratepages: make aio migrate pages sane
aio: fix kioctx leak introduced by "aio: Fix a trinity splat"
Don't set the INITRD_COMPRESS environment variable automatically
mm: fix build of split ptlock code
pstore: Don't allow high traffic options on fragile devices
mm: do not allocate page->ptl dynamically, if spinlock_t fits to long
mm: page_alloc: revert NUMA aspect of fair allocation policy
Revert "mm: page_alloc: exclude unreclaimable allocations from zone fairness policy"
mm: Fix NULL pointer dereference in madvise(MADV_WILLNEED) support
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
target: Remove extra percpu_ref_init
arm64: ptrace: avoid using HW_BREAKPOINT_EMPTY for disabled events
ARC: Allow conditional multiple inclusion of uapi/asm/unistd.h
target/file: Update hw_max_sectors based on current block_size
iser-target: Move INIT_WORK setup into isert_create_device_ib_res
iscsi-target: Fix incorrect np->np_thread NULL assignment
mm/hugetlb: check for pte NULL pointer in __page_check_address()
fix build with make 3.80
...
Conflicts:
drivers/usb/phy/Kconfig
Some module names are not up to date in Kconfig help texts. Fix that.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
phy-isp1301-omap produces the following smatch warnings:
drivers/usb/phy/phy-isp1301-omap.c:1280 isp1301_set_host() warn: variable dereferenced before check 'otg' (see line 1278)
drivers/usb/phy/phy-isp1301-omap.c:1336 isp1301_set_peripheral() warn: variable dereferenced before check 'otg' (see line 1334)
drivers/usb/phy/phy-isp1301-omap.c:1417 isp1301_start_srp() warn: variable dereferenced before check 'otg' (see line 1414)
drivers/usb/phy/phy-isp1301-omap.c:1445 isp1301_start_hnp() warn: variable dereferenced before check 'otg' (see line 1442)
Fix by deleting bogus NULL pointer checks. The USB framework will always
call us with a valid OTG pointer.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
phy-tahvo introduced the following smatch warnings:
drivers/usb/phy/phy-tahvo.c:203 tahvo_usb_set_host() warn: variable dereferenced before check 'otg' (see line 199)
drivers/usb/phy/phy-tahvo.c:235 tahvo_usb_set_peripheral() warn: variable dereferenced before check 'otg' (see line 231)
Fix by deleting bogus NULL pointer checks. The USB framework will always
call us with a valid OTG pointer.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Silences the below warning:
WARNING: sizeof *twl should be sizeof(*twl)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Robert Jarzmik