Set the dma for ehci from sysdev. The sysdev is pointing to device that
is known to the system firmware or hardware.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For xhci-hcd platform device, all the DMA parameters are not
configured properly, notably dma ops for dwc3 devices. So, set
the dma for xhci from sysdev. sysdev is pointing to device that
is known to the system firmware or hardware.
Cc: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a loaded virtualization host (dozen guests booting at the same time)
it may happen that the ohci controller emulation doesn't manage to do
timely frame processing, with the result that the io watchdog fires and
considers the controller being dead, even though it's only the emulation
being unusual slow due to the load peak.
So, add a quirk for qemu and don't use the watchdog in case we figure we
are running on emulated ohci. The virtual ohci controller masquerades
as apple ohci controller, but we can identify it by subsystem id.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch sets hcd->phy from own phy context to avoid phy_get()
in usb_add_hcd(). Since core/hcd.c manages the phy only in
usb_add_hcd() and usb_remove_hcd(), there is difficult to manage
the phy in suspend/resume.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch sets hcd->phy from own phy context to avoid phy_get()
in usb_add_hcd(). Since core/hcd.c manages the phy only in
usb_add_hcd() and usb_remove_hcd(), there is difficult to manage
the phy in suspend/resume.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mvebu ARM64 SoCs no longer select PLAT_ORION. However Armada 37xx use
the Orion EHCI controller. This patch allows the Orion EHCI driver to be
built when ARCH_MVEBU is selected.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Add a new compatible string for the Armada 3700 SoCs
- add sbuscfg support for orion usb controller driver. For the SoCs
without hlock, need to program BAWR/BARD/AHBBRST fields in the sbuscfg
register to guarantee the AHB master's burst would not overrun or
underrun the FIFO.
- the sbuscfg register has to be set after the usb controller reset,
otherwise the value would be overridden to 0. In order to do this, the
reset callback is registered.
[gregory.clement@free-electrons.com: - reword commit and comments
- fix error path in ehci_orion_drv_reset()
- fix checkpatch warning]
Signed-off-by: Hua Jing <jinghua@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue that a usb 1.1 device is not connected in
system resume and then the following message appeared if debug messages
are enabled:
usb 2-1: Waited 2000ms for CONNECT
To resolve this issue, the EHCI controller must be resumed after its
companion controllers. So, this patch adds such code on the driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
a lot of embeded system SOC (e.g. freescale T2080) have both
PCI and USB modules. But USB module is controlled by registers directly,
it have no relationship with PCI module.
when say N here it will not build PCI related code in USB driver.
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This replaces remaining occurences of pci_pool by dma_pool, as
this is the new API that could be used for that purpose.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is a number of different USB fixes for 4.11-rc2. Seems like there
were a lot of unresolved issues that people have been finding for this
subsystem, and a bunch of good security auditing happening as well from
Johan Hovold. There's the usual batch of gadget driver fixes and xhci
issues resolved as well.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWMOkLA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymiCACeIL3h4bNEc6+XLiB+sfmQx4wV2MUAnRMD1gB0
GxkBXY1Iny94vhZC8x5r
=dlkm
-----END PGP SIGNATURE-----
Merge tag 'usb-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a number of different USB fixes for 4.11-rc2.
Seems like there were a lot of unresolved issues that people have been
finding for this subsystem, and a bunch of good security auditing
happening as well from Johan Hovold. There's the usual batch of gadget
driver fixes and xhci issues resolved as well.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (35 commits)
usb: host: xhci-plat: Fix timeout on removal of hot pluggable xhci controllers
usb: host: xhci-dbg: HCIVERSION should be a binary number
usb: xhci: remove dummy extra_priv_size for size of xhci_hcd struct
usb: xhci-mtk: check hcc_params after adding primary hcd
USB: serial: digi_acceleport: fix OOB-event processing
MAINTAINERS: usb251xb: remove reference inexistent file
doc: dt-bindings: usb251xb: mark reg as required
usb: usb251xb: dt: add unit suffix to oc-delay and power-on-time
usb: usb251xb: remove max_{power,current}_{sp,bp} properties
usb-storage: Add ignore-residue quirk for Initio INIC-3619
USB: iowarrior: fix NULL-deref in write
USB: iowarrior: fix NULL-deref at probe
usb: phy: isp1301: Add OF device ID table
usb: ohci-at91: Do not drop unhandled USB suspend control requests
USB: serial: safe_serial: fix information leak in completion handler
USB: serial: io_ti: fix information leak in completion handler
USB: serial: omninet: drop open callback
USB: serial: omninet: fix reference leaks at open
USB: serial: io_ti: fix NULL-deref in interrupt callback
usb: dwc3: gadget: make to increment req->remaining in all cases
...
Fix typos and add the following to the scripts/spelling.txt:
disble||disable
disbled||disabled
I kept the TSL2563_INT_DISBLED in /drivers/iio/light/tsl2563.c
untouched. The macro is not referenced at all, but this commit is
touching only comment blocks just in case.
Link: http://lkml.kernel.org/r/1481573103-11329-20-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Upstream commit 98d74f9cea ("xhci: fix 10 second timeout on removal of
PCI hotpluggable xhci controllers") fixes a problem with hot pluggable PCI
xhci controllers which can result in excessive timeouts, to the point where
the system reports a deadlock.
The same problem is seen with hot pluggable xhci controllers using the
xhci-plat driver, such as the driver used for Type-C ports on rk3399.
Similar to hot-pluggable PCI controllers, the driver for this chip
removes the xhci controller from the system when the Type-C cable is
disconnected.
The solution for PCI devices works just as well for non-PCI devices
and avoids the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to xHCI spec, HCIVERSION containing a BCD encoding
of the xHCI specification revision number, 0100h corresponds
to xHCI version 1.0. Change "100" as "0x100".
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 04abb6de28 ("xhci: Read and parse new xhci
1.1 capability register")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hcc_params is set in xhci_gen_setup() called from usb_add_hcd(),
so checks the Maximum Primary Stream Array Size in the hcc_params
register after adding primary hcd.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In patch 2e2aa1bc7eff90ecm, USB suspend and wakeup control requests are
passed to SFR_OHCIICR register. If a processor does not have such a
register, this hub control request will be dropped.
If no such a SFR register is available, all USB suspend control requests
will now be processed using ohci_hub_control()
(like before patch 2e2aa1bc7eff90ecm.)
Tested on an Atmel AT91SAM9G20 with an on-board TI TUSB2046B hub chip
If the last USB device is unplugged from the USB hub, the hub goes into
sleep and will not wakeup when an USB devices is inserted.
Fixes: 2e2aa1bc7e ("usb: ohci-at91: Forcibly suspend ports while USB suspend")
Signed-off-by: Jelle Martijn Kok <jmkok@youcom.nl>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.
Use BUILD_BUG_ON in a couple ATM drivers.
In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.
Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "dbg_port" macro uses the "outside" parameter (="temp") instead of
the parameters (="value") given in the macro. As the macro can look
outside its definition this causes no direct problem.
Signed-off-by: Jelle Martijn Kok <jmkok@youcom.nl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the reference clock optional for DTS backward compatibility
and ignore the error if it does not exist.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use switch instead of several if statements
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of storing a zero length array of td pointers, and then
allocate memory both for the td pointer array and the td's, just
use a zero length array of actual td's in urb private data.
old:
struct urb_priv {
struct xhci_td *td[0]
}
new:
struct urb_priv {
struct xhci_td td[0]
}
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
urb_priv structure has a count on how many TDs the
URB contains, and how many of those TD's we have handled.
rename:
length -> num_tds
td_cnt -> num_tds_done
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functinal changes.
num_tds describes the number of transfer descriptor better than "size"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's start tracing at least part of an xhci_virt_device lifetime. We
might want to extend this tracepoint class later, but for now it already
exposes quite a bit of valuable information.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we add that newline, the output will look like the following:
kworker/2:1-42 [002] .... 169.811435: xhci_address_ctx:
ctx_64=0, ctx_type=2, ctx_dma=@153fbd000, ctx_va=@ffff880153fbd000
We would rather have that in a single line.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when getting endpoint type, a switch statement looks
better than a series of if () branches. There are no
functional changes with this patch, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These three new tracers will help us tie TRBs into URBs by *also*
looking into URB lifetime.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
instead of having a tracer that can only trace command completions,
let's promote this tracer so it can trace and decode any TRB.
With that, it will be easier to extrapolate the lifetime of any TRB
which might help debugging certain issues.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we just provide a helper to convert completion code to string, we can
combine all debugging messages into a single print.
[keep the old debug messages, for warn and grep -Mathias]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
instead of using while(!list_empty()) followed by list_first_entry(), we
can actually use list_for_each_entry_safe().
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove duplicate code by using trb_to_noop() when
handling Aborted commads
Based on earlier code by Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Useful for turning both transfer and command trbs
into no-ops.
Based on earlier code by Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_unmap_td_bounce_buffer() already checks for a valid td->bounce_seg
and bails out early if that's invalid. There's no need to check for this
twice.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This way we can remove checks for valid ring from call sites of
xhci_unmap_td_bounce_buffer()
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
handle_tx_event() is not releasing xhci->lock nor reacquiring it, remove
the bogus annotation.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By extracting xhci_td_cleanup() from finish_td(), code before clearer
and easier to follow.
There are no functional changes with this patch. It's merely a cleanup.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
no functional changes. Simple cleanup to make sure variables are ordered
in a 'reverse christmas tree' fashion. While at that, also remove an
obsolete comment which doesn't apply anymore.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace list_entry() with list_first_entry() and list_for_each() with
list_for_each_entry(). This makes the code slightly more readable.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
it does no good, let's remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of having several return points, let's use a local variable and
a single place to return. This makes the code slightly easier to read.
[set ret = IRQ_HANDLED in default working case -Mathias]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cleanup only. This patch is a mechaninal rename to make sure our macros
for TRB completion codes match what the specification uses to refer to
such errors. The idea behind this is that it makes it far easier to grep
the specification and match it with implementation.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling xhci_dbg_regs() we actually _do_ want to know XHCI's
version. This might help figure out why certain problems only happen
in some cases.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a cleanup patch only, no functional changes. The idea is just to
make sure for loops look the same all over the driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the unnecessary return line in xhci_pci_setup().
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use list_is_singular() to check if cmd_list has only one entry.
[use list_empty() in queue command instead -Mathias]
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to calculate remainder and length_field, if there is
no data phase of a control transfer.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop an unnecessary assignment in prepare_transfer().
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case 'quirk-broken-port-ped' property is passed in via device property,
we should enable the corresponding BROKEN_PED quirk flag for XHCI core.
[rogerq@ti.com] Updated code from platform data to device property
and added DT binding.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices from Texas Instruments [1] suffer from
a silicon bug where Port Enabled/Disabled bit
should not be used to silence an erroneous device.
The bug is so that if port is disabled with PED
bit, an IRQ for device removal (or attachment)
will never fire.
Just for the sake of completeness, the actual
problem lies with SNPS USB IP and this affects
all known versions up to 3.00a. A separate
patch will be added to dwc3 to enabled this
quirk flag if version is <= 3.00a.
[1] - AM572x Silicon Errata http://www.ti.com/lit/er/sprz429j/sprz429j.pdf
Section i896— USB xHCI Port Disable Feature Does Not Work
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows someone to grep for the complete warning message as in;
xhci-hcd xhci-hcd.0.auto: USB core suspending device not in U0/U1/U2.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the 'addr_64' variable as legacy is unused now, then remove it from
xhci_hcd structure.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The second try was a workaround for (what we thought was) command
ring failing to stop in the first place. But this turns out to be
due to the race that we have fixed(see "xhci: Fix race related to
abort operation"). With that fix, it is time to remove the second
try.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checking if the command timeout timer is pending when queueing the
first command to the command ring is not really useful, remove it.
Suggested-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A counter was used to find out if the stop endpoint completion raced with
the stop endpoint timeout timer. This was needed in case the stop ep
completion failed to delete the timer as it was running on anoter cpu.
The EP_STOP_CMD_PENDING flag was not enough as a new stop endpoint command
may be queued between the command completion and timeout function, which
would set the flag back.
Instead of the separate counter that was used we can detect the race by
checking both the STOP_EP_PENDING flag and timer_pending in the timeout
function.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't want to confuse halted and stalled endpoint states with
a flag indicating we are waiting for a stop endpoint command to
finish or timeout
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functional change, De Morgan !(A && B) = (!A || !B)
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The warn on is a bit too much, we will anyway set the dma mask if not set
previously.
The main reason for this fix is that 4.10-rc1 has a dwc3 change that
pass a parent sysdev dev pointer instead of setting the dma mask of
its xhci platform device. xhci platform driver can then get more
attributes from the sysdev than just the dma mask.
The usb core and xhci changes are not yet in 4.10, and a fix like
this was preferred instead of taking those big changes this late in
the rc-cycle.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usually, the reference clock comes from 26M oscillator directly,
but some SoCs are not, add it for compatibility.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 4ac53087d6 ("usb: xhci: plat: Create both
HCDs before adding them") move add hcd to the end of
probe, this cause hcc_params uninitiated, because xHCI
driver sets hcc_params in xhci_gen_setup() called from
usb_add_hcd().
This patch checks the Maximum Primary Stream Array Size
in the hcc_params register after add primary hcd.
Signed-off-by: William wu <william.wu@rock-chips.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Cc: stable <stable@vger.kernel.org> # 4.2+
Fixes: 4ac53087d6 ("usb: xhci: plat: Create both HCDs before adding them")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declare dev_pm_ops structures as const as they are only stored in the pm
field of a device_driver structure. This field is of type const, so
dev_pm_ops structures having similar properties can be declared const
too.
Size details after cross compiling the .o file for powerpc
architecture.
File size before:
text data bss dec hex filename
3183 372 0 3555 de3 drivers/usb/host/ehci-fsl.o
File size after:
text data bss dec hex filename
3275 280 0 3555 de3 drivers/usb/host/ehci-fsl.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable live was assigned the host controller running status but
it was never used or checked after that.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here to make merges easier/possible with the
other sub-maintainer USB trees.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a URB is killed while the host is removed we can end up in a situation
where the hub thread takes the roothub device lock, and waits for
the URB to be given back by xhci-hcd, blocking the host remove code.
xhci-hcd tries to stop the endpoint and give back the urb, but can't
as the host is removed from PCI bus at the same time, preventing the normal
way of giving back urb.
Instead we need to rely on the stop command timeout function to give back
the urb. This xhci_stop_endpoint_command_watchdog() timeout function
used a XHCI_STATE_DYING flag to indicate if the timeout function is already
running, but later this flag has been taking into use in other places to
mark that xhci is dying.
Remove checks for XHCI_STATE_DYING in xhci_urb_dequeue. We are still
checking that reading from pci state does not return 0xffffffff or that
host is not halted before trying to stop the endpoint.
This whole area of stopping endpoints, giving back URBs, and the wathdog
timeout need rework, this fix focuses on solving a specific deadlock
issue that we can then send to stable before any major rework.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Returning from for_each_available_child_of_node() loop requires cleaning
up node refcount. Error paths lacked it so for example in case of
deferred probe, the refcount of phy node was left increased.
Fixes: 6d40500ac9 ("usb: ehci/ohci-exynos: Fix of_node_put() for child when getting PHYs")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Returning from for_each_available_child_of_node() loop requires cleaning
up node refcount. Error paths lacked it so for example in case of
deferred probe, the refcount of phy node was left increased.
Fixes: 6d40500ac9 ("usb: ehci/ohci-exynos: Fix of_node_put() for child when getting PHYs")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MIPS based MT7621 shares the same XHCI core as the newer generation of
ARM based SoCs. The driver works out of the box and we only need to make it
buildable in Kconfig.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Defer probe if PHY is missing. E.g. on Nokia 770 several modules needs
to be loaded to get the PHY going and ohci-omap should wait for those.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gpiod_get* function family does not want the -gpio suffix.
Use devm_gpiod_get_index_optional instead of devm_gpiod_get_optional.
The descriptor based APIs handle active high/low automatically.
The vbus-gpios are output, request enable while getting the gpio.
Don't try to get any vbus-gpios for ports outside num-ports.
WTF? Big sigh.
Fixes: 054d4b7b57 ("usb: ohci-at91: Use descriptor-based gpio APIs")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop Endpoint command can come at any point and we
have no control of that. We should make sure to
handle COMP_STOP on SETUP phase as well, otherwise
urb->actual_length might be set to negative values
in some occasions such as below:
urb->length = 4;
build_control_transfer_td_for(urb, ep);
stop_endpoint(ep);
COMP_STOP:
[...]
urb->actual_length = urb->length - trb->length;
trb->length is 8 for SETUP stage (8 control request
bytes), so actual_length would be set to -4 in this
case.
While doing that, also make sure to use TRB_TYPE
field of the actual TRB instead of matching pointers
to figure out in which stage of the control transfer
we got our completion event.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Apollo Lake also requires XHCI_PME_STUCK_QUIRK.
Adding its PCI ID to quirk.
Cc: <stable@vger.kernel.org>
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current abort operation has race.
xhci_handle_command_timeout()
xhci_abort_cmd_ring()
xhci_write_64(CMD_RING_ABORT)
xhci_handshake(5s)
do {
check CMD_RING_RUNNING
udelay(1)
...
COMP_CMD_ABORT event
COMP_CMD_STOP event
xhci_handle_stopped_cmd_ring()
restart cmd_ring
CMD_RING_RUNNING become 1 again
} while ()
return -ETIMEDOUT
xhci_write_64(CMD_RING_ABORT)
/* can abort random command */
To do abort operation correctly, we have to wait both of COMP_CMD_STOP
event and negation of CMD_RING_RUNNING.
But like above, while timeout handler is waiting negation of
CMD_RING_RUNNING, event handler can restart cmd_ring. So timeout
handler never be notice negation of CMD_RING_RUNNING, and retry of
CMD_RING_ABORT can abort random command (BTW, I guess retry of
CMD_RING_ABORT was workaround of this race).
To fix this race, this moves xhci_handle_stopped_cmd_ring() to
xhci_abort_cmd_ring(). And timeout handler waits COMP_CMD_STOP event.
At this point, timeout handler is owner of cmd_ring, and safely
restart cmd_ring by using xhci_handle_stopped_cmd_ring().
[FWIW, as bonus, this way would be easily extend to add CMD_RING_PAUSE
operation]
[locks edited as patch is rebased on other locking fixes -Mathias]
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is preparation to fix abort operation race (See "xhci: Fix race
related to abort operation"). To make timeout sleepable, use
delayed_work instead of timer.
[change a newly added pending timer fix to pending work -Mathias]
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In command timer function, xhci_handle_command_timeout(), xhci->lock
is unlocked before call into xhci_abort_cmd_ring(). This might cause
race between the timer function and the event handler.
The xhci_abort_cmd_ring() function sets the CMD_RING_ABORT bit in the
command register and polling it until the setting takes effect. A stop
command ring event might be handled between writing the abort bit and
polling for it. The event handler will restart the command ring, which
causes the failure of polling, and we ever believed that we failed to
stop it.
As a bonus, this also fixes some issues of calling functions without
locking in xhci_handle_command_timeout().
Cc: <stable@vger.kernel.org> # 3.7+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we get a command completion event at the same time as the command
timeout work starts on another cpu we might end up aborting the wrong
command.
If the command completion takes the xhci lock before the timeout work, it
will handle the command, pick the next command, mark it as current_cmd, and
re-queue the timeout work. When the timeout work finally gets the lock
It will start aborting the wrong command.
This case can be resolved by checking if the timeout work is pending inside
the timeout function itself. A new timeout work can only be pending if the
command completed and a new command was queued.
If there are no more commands pending then command completion will set
the current_cmd to NULL, which is already handled in the timeout work.
Cc: <stable@vger.kernel.org>
Reported-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When current command was supposed to be aborted, host will free the command
in handle_cmd_completion() function. But it might be still referenced by
xhci->current_cmd, which need to set NULL.
Cc: <stable@vger.kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
handle_cmd_completion() frees a command structure which might be still
referenced by xhci->current_cmd.
This might cause problem when xhci->current_cmd is accessed after that.
A real-life case could be like this. The host takes a very long time to
respond to a command, and the command timer is fired at the same time
when the command completion event arrives. The command completion
handler frees xhci->current_cmd before the timer function can grab
xhci->lock. Afterward, timer function grabs the lock and go ahead with
checking and setting members of xhci->current_cmd.
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function xhci_mtk_probe(), variable ret takes the return value. Its
value should be negative on failures. However, when the call to function
platform_get_irq() fails, it does not set the error code, and 0 will be
returned. 0 indicates no error. As a result, the callers of function
xhci_mtk_probe() will not be able to detect the error. This patch fixes
the bug by assigning the return value of platform_get_irq() to variable
ret if it fails.
CC: <stable@vger.kernel.org>
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_setup_device() should return failure with correct error number
when xhci host has died, removed or halted.
During usb device enumeration, if usb host is not accessible (died,
removed or halted), the hc_driver->address_device() should return
a corresponding error code to usb core. But current xhci driver just
returns success. This misleads usb core to continue the enumeration
by reading the device descriptor, which will result in failure, and
users will get a misleading message like "device descriptor read/8,
error -110".
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the tt_info provided by a HS hub might be in use to by a child device
Make sure we free the devices in the correct order.
This is needed in special cases such as when xhci controller is
reset when resuming from hibernate, and all virt_devices are freed.
Also free the virt_devices starting from max slot_id as children
more commonly have higher slot_id than parent.
CC: <stable@vger.kernel.org>
Reported-by: Guenter Roeck <groeck@chromium.org>
Tested-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ut0k
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI changes:
- add support for PCI on ARM64 boxes with ACPI. We already had this
for theoretical spec-compliant hardware; now we're adding quirks
for the actual hardware (Cavium, HiSilicon, Qualcomm, X-Gene)
- add runtime PM support for hotplug ports
- enable runtime suspend for Intel UHCI that uses platform-specific
wakeup signaling
- add yet another host bridge registration interface. We hope this is
extensible enough to subsume the others
- expose device revision in sysfs for DRM
- to avoid device conflicts, make sure any VF BAR updates are done
before enabling the VF
- avoid unnecessary link retrains for ASPM
- allow INTx masking on Mellanox devices that support it
- allow access to non-standard VPD for Chelsio devices
- update Broadcom iProc support for PAXB v2, PAXC v2, inbound DMA,
etc
- update Rockchip support for max-link-speed
- add NVIDIA Tegra210 support
- add Layerscape LS1046a support
- update R-Car compatibility strings
- add Qualcomm MSM8996 support
- remove some uninformative bootup messages"
* tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (115 commits)
PCI: Enable access to non-standard VPD for Chelsio devices (cxgb3)
PCI: Expand "VPD access disabled" quirk message
PCI: pciehp: Remove loading message
PCI: hotplug: Remove hotplug core message
PCI: Remove service driver load/unload messages
PCI/AER: Log AER IRQ when claiming Root Port
PCI/AER: Log errors with PCI device, not PCIe service device
PCI/AER: Remove unused version macros
PCI/PME: Log PME IRQ when claiming Root Port
PCI/PME: Drop unused support for PMEs from Root Complex Event Collectors
PCI: Move config space size macros to pci_regs.h
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI/ASPM: Don't retrain link if ASPM not possible
PCI: iproc: Skip check for legacy IRQ on PAXC buses
PCI: pciehp: Leave power indicator on when enabling already-enabled slot
PCI: pciehp: Prioritize data-link event over presence detect
PCI: rcar: Add gen3 fallback compatibility string for pcie-rcar
PCI: rcar: Use gen2 fallback compatibility last
PCI: rcar-gen2: Use gen2 fallback compatibility last
PCI: rockchip: Move the deassert of pm/aclk/pclk after phy_init()
..
This patch will fix the checkpatch.pl following warnings:
WARNING: Missing a blank line after declarations
WARNING: braces {} are not necessary for single statement blocks
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ohci_hcd_pxa27x_drv_probe function is not doing anything other
than calling usb_hcd_pxa27x_probe function so ohci_hcd_pxa27x_drv_probe
function is useless that is why removed ohci_hcd_pxa27x_drv_probe
function and renamed usb_hcd_pxa27x_probe function to
ohci_hcd_pxa27x_drv_probe for proper naming.
The ohci_hcd_pxa27x_remove function is also not doing anything other than
calling usb_hcd_pxa27x_remove that is why removed ohci_hcd_pxa27x_remove
function and renamed usb_hcd_pxa27x_remove to ohci_hcd_pxa27x_remove for
proper naming.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ohci_hcd_omap_drv_probe and ohci_hcd_omap_drv_remove
functions are removed as these are useless functions except calling
usb_hcd_omap_probe and usb_hcd_omap_remove functions.
The usb_hcd_omap_probe function renamed to ohci_hcd_omap_probe
and usb_hcd_omap_remove function renamed to ohci_hcd_omap_remove
for proper naming.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ohci_hcd_s3c2410_drv_probe and ohci_hcd_s3c2410_drv_remove
functions are removed as these are useless functions except calling
usb_hcd_s3c2410_probe and usb_hcd_s3c2410_remove functions.
The usb_hcd_s3c2410_probe function renamed to ohci_hcd_s3c2410_drv_probe
and usb_hcd_s3c2410_remove function renamed to ohci_hcd_s3c2410_drv_remove
for proper naming.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The EHCI specification states the following in the SUSP bit description:
In the Suspend state, the port is sensitive to resume detection.
Note that the bit status does not change until the port is suspended and
that there may be a delay in suspending a port if there is a transaction
currently in progress on the USB.
However, in NXP USBDR controller, the PORTSCx[SUSP] bit changes immediately
when the application sets it and not when the port is actually suspended.
So the application must wait for at least 10 milliseconds after a port
indicates that it is suspended, to make sure this port has entered
suspended state before initiating this port resume using the Force Port
Resume bit. This bit is for NXP controller, not EHCI compatible.
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ehci_w90x900_probe function is not doing anything other than
calling usb_w90x900_probe function so ehci_w90x900_probe function
is unuseful that is why removed ehci_w90x900_probe functions and
renamed usb_w90x900_probe function to ehci_w90x900_probe for proper
naming.
The ehci_w90x900_remove function is also not doing anything other
than calling usb_w90x900_remove that is why removed ehci_w90x900_remove
function and renamed usb_w90x900_remove to ehci_w90x900_remove for proper
naming.
This also removes warning of checkpatch.pl script.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The da8xx ohci controller is not working after suspend and resume.
This is because only the root hub is being resumed.
Balance the ohci_suspend of the suspend path with an ohci_resume
in the resume path so that we resume the entire controller, and not
just the root hub.
Also, while we are here, remove setting device power_state,
as this is no longer needed and scheduled for removal
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the compatible string to the ohci driver
to be able to probe from DT
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using a regulator to handle VBUS will eliminate the need for
platform data and callbacks, and make the driver more generic
allowing different types of regulators to handle VBUS.
The regulator equivalents to the platform callbacks are:
set_power -> regulator_enable/regulator_disable
get_power -> regulator_is_enabled
get_oci -> regulator_get_error_flags
ocic_notify -> regulator event notification
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To migrate to a DT based boot, we will remove the use of platform
callbacks, in favor of using the regulator framework to handle
vbus and over current.
In preparation to use a regulator instead of callbacks, move the platform
data callbacks into separate functions. This provides well defined place
to for the regulator API to coexist with the platform callbacks before
all users are converted.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen