Commit Graph

11860 Commits

Author SHA1 Message Date
Hans Verkuil ddac5c1079 [media] v4l2-ctrls: fix and improve volatile control handling
If you have a cluster of controls that is a mix of volatile and non-volatile
controls, then requesting the value of the volatile control would fail if the
master control of that cluster was non-volatile. The code assumed that the
volatile state of the master control was the same for all other controls in
the cluster.

This is now fixed.

In addition, it was clear from bugs in some drivers that it was confusing that
the ctrl->cur union had to be used in g_volatile_ctrl. Several drivers used the
'new' values instead. The framework was changed so that drivers now set the new
value instead of the current value.

This has an additional benefit as well: the volatile values are now only stored
in the 'new' value, leaving the current value alone. This is useful for
autofoo/foo control clusters where you want to have a 'foo' control act like a
volatile control if 'autofoo' is on, but as a normal control when it is off.

Since with this change the cur value is no longer overwritten when g_volatile_ctrl
is called, you can use it to remember the original 'foo' value. For example:

autofoo = 0, foo = 10 and foo is non-volatile.

Now autofoo is set to 1 and foo is marked volatile. Retrieving the foo value
will get the volatile value. Set autofoo back to 0, which marks foo as non-
volatile again, and retrieving foo will get the old current value of 10.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:17 -03:00
Hans Verkuil 18d171badf [media] v4l2-subdev: implement per-filehandle control handlers
To be consistent with v4l2-ioctl.c.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:17 -03:00
Hans Verkuil 2d28b686ad [media] v4l2-ioctl: add ctrl_handler to v4l2_fh
This is required to implement control events and is also needed to allow
for per-filehandle control handlers.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:17 -03:00
Hans Verkuil 7ebbc39fa0 [media] v4l2-ctrls: drivers should be able to ignore the READ_ONLY flag
When applications try to set READ_ONLY controls an error should
be returned. However, when drivers do that it should be accepted.

Those controls could reflect some driver status which the application
can't change but the driver obviously has to be able to change it.

This is needed among others for future HDMI status controls.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:17 -03:00
Hans Verkuil 37cd3b7368 [media] v4l2-ctrls: simplify error_idx handling
The lower-level prepare functions just set error_idx for each control that
might have an error. The high-level functions will override this with
cs->count in the get and set cases. Only try will keep the error_idx.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:16 -03:00
Hans Verkuil 54c911eb91 [media] v4l2-ctrls: introduce call_op define
Add the call_op define to safely call the control ops. This also allows
for controls without any ops such as the 'control class' controls.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:16 -03:00
Mauro Carvalho Chehab 29834c1ac7 [media] radio: Use the subsystem version control for VIDIOC_QUERYCAP
Just like the video drivers, the right thing to do is to use
the per-subsystem version control.

Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:16 -03:00
Mauro Carvalho Chehab 64dc3c1a90 [media] Stop using linux/version.h on the remaining video drivers
Standardize the remaining video drivers to return the API version
for the VIDIOC_QUERYCAP version, instead of a per-driver version.

Those drivers had the version updated more recently or are SoC
drivers. Even so, it doesn't sound a good idea to keep a per-driver
version control, so, let's use the per-subsystem version control
instead.

Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:16 -03:00
Mauro Carvalho Chehab b0eaab7657 [media] gspca: don't include linux/version.h
Instead of handling a per-driver driver version, use the
per-subsystem one.

As reviewed by Jean-Francois Moine <moinejf@free.fr>:
	- the 'info' may be simplified:

Reviewed-by: Jean-Francois Moine <moinejf@free.fr>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:15 -03:00
Mauro Carvalho Chehab fd3e582482 [media] uvcvideo: Use LINUX_VERSION_CODE for VIDIOC_QUERYCAP
uvcvideo doesn't use vidioc_ioctl2. As the API is changing to use
a common version for all drivers, we need to expliticly fix this
driver.

Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:15 -03:00
Mauro Carvalho Chehab 6c13b45e57 [media] sn9c102: Use LINUX_VERSION_CODE for VIDIOC_QUERYCAP
sn9c102 doesn't use vidioc_ioctl2. As the API is changing to use
a common version for all drivers, we need to expliticly fix this
driver.

Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:15 -03:00
Mauro Carvalho Chehab 083774d8b1 [media] pvrusb2: Use LINUX_VERSION_CODE for VIDIOC_QUERYCAP
pvrusb2 doesn't use vidioc_ioctl2. As the API is changing to use
a common version for all drivers, we need to expliticly fix this
driver.

Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:15 -03:00
Mauro Carvalho Chehab 5204cebadd [media] et61x251: Use LINUX_VERSION_CODE for VIDIOC_QUERYCAP
et61x251 doesn't use vidioc_ioctl2. As the API is changing to use
a common version for all drivers, we need to expliticly fix this
driver.

Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:15 -03:00
Mauro Carvalho Chehab 3c2d464ee8 [media] ivtv,cx18: Use default version control for VIDIOC_QUERYCAP
After discussing with Andy Walls on irc, we've agreed that this
is the best thing to do. No regressions will be introduced, as 3.x.y
is greater then the current versions for cx18 and ivtv.

Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:14 -03:00
Mauro Carvalho Chehab 880c35c585 [media] pwc: Use the default version for VIDIOC_QUERYCAP
After discussing with Hans, change pwc to use the default version
control.

The only version ever used for pwc driver is 10.0.12, due to
commit 2b455db6d4.

Changing it to 3.x.y won't conflict with the old version.
There's no namespace conflicts in any predictable future.

Even on the remote far-away case where we might have a conflict,
it will be on just one specific stable Kernel release (Kernel 10.0.12),
if we ever have such stable release.

So, it is safe and consistent on using 3.x.y numering schema for
it.

Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:12 -03:00
Mauro Carvalho Chehab 1990d50b58 [media] Stop using linux/version.h on most video drivers
All the modified drivers didn't have any version increment since
Jan, 1 2011. Several of them didn't have any version increment
for a long time, even having new features and important bug fixes
happening.

As we're now filling the QUERYCAP version with the current Kernel
Release, we don't need to maintain a per-driver version control
anymore. So, let's just use the default.

In order to preserve the Kernel module version history, a
KERNEL_VERSION() macro were added to all modified drivers, and
the extraver number were incremented.

I opted to preserve the per-driver version control to a few
pwc, pvrusb2, s2255, s5p-fimc and sh_vou.

A few drivers are still using the legacy way to handle ioctl's.
So, we can't do such change on them, otherwise, they'll break.
Those are: uvc, et61x251 and sn9c102.

The rationale is that the per-driver version control seems to be
actively maintained on those.

Yet, I think that the better for them would be to just use the
default version numbering, instead of doing that by themselves.

While here, removed a few uneeded include linux/version.h

Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:12 -03:00
Mauro Carvalho Chehab d35ebf9558 [media] drxd, siano: Remove unused include linux/version.h
Both drxd and siano drivers were including linux/version.h without
any reason. Probably, this is due to some compatibility code that
used to exist before having their support added into the Linux
Kernel.

Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:12 -03:00
Mauro Carvalho Chehab ae6db51546 [media] v4l2-ioctl: Add a default value for kernel version
Most drivers don't increase kernel versions as newer features are added or
bug fixes are solved. So, vidioc_querycap returned value for cap->version is
meaningless. Instead of keeping this situation forever, let's add a default
value matching the current Linux version.

Drivers that want to keep their own version control can still do it, as they
can override the default value for cap->version.

Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:12 -03:00
Jonathan Corbet a9b36e8507 [media] marvell-cam: implement contiguous DMA operation
The core driver can now operate in either vmalloc or dma-contig modes;
obviously the latter is preferable when it is supported.  Default is
currently vmalloc on all platforms; load the module with buffer_mode=1 for
contiguous DMA mode.

Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:11 -03:00
Jonathan Corbet 6c895d548c [media] marvell-cam: Don't spam the logs on frame loss
The sequence numbers already give that information if user space cares;
this is a frequent occurrence on slower machines, alas.

Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:11 -03:00
Jonathan Corbet 9d48a51c27 [media] marvell-cam: no need to initialize the DMA buffers
This was an old debugging thing from years ago.  It's only done at
initialization time, but it's still unnecessary; take it out.

Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:11 -03:00
Jonathan Corbet 362d45b23d [media] marvell-cam: include file cleanup
Put the includes into a slightly more readable ordering and get rid of a
few unneeded ones.

Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:11 -03:00
Jonathan Corbet b5210fd2c7 [media] marvell-cam: convert to videobuf2
This is a basic, naive conversion to the videobuf2 infrastructure, removing
a lot of code in the process.  For now, we're using vmalloc, which is
suboptimal, but it does match what the cafe driver did before.  In the cafe
case, it may have to stay that way just because memory is too tight to do
direct streaming; mmp-camera will be able to do better.

Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:11 -03:00
Manjunath Hadli 6783edbc83 [media] davinci vpbe: Build infrastructure for VPBE driver
This patch adds the build infra-structure for Davinci
VPBE dislay driver.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:10 -03:00
Manjunath Hadli 606b69e9b9 [media] davinci vpbe: VENC( Video Encoder) implementation
This patch adds the VENC or the Video encoder, which is responsible
for the blending of all source planes and timing generation for Video
modes like NTSC, PAL and other digital outputs. the VENC implementation
currently supports COMPOSITE and COMPONENT outputs and NTSC and PAL
resolutions through the analog DACs. The venc block is implemented
as a subdevice, allowing for additional external and internal encoders
of other kind to plug-in.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:10 -03:00
Manjunath Hadli ff0f23dd0e [media] davinci vpbe: OSD(On Screen Display) block
This patch implements the functionality of the OSD block
of the VPBE. The OSD in total supports 4 planes or Video
sources - 2 mainly RGB and 2 Video. The patch implements general
handling of all the planes, with specific emphasis on the Video
plane capabilities as the Video planes are supported through the
V4L2 driver.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:10 -03:00
Manjunath Hadli 66715cdc32 [media] davinci vpbe: VPBE display driver
This patch implements the core functionality of the display driver,
mainly controlling the VENC and other encoders, and acting as
the one point interface for the main V4L2 driver. This implements
the core of each of the V4L2 IOCTLs.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:09 -03:00
Manjunath Hadli a2c25b444e [media] davinci vpbe: V4L2 display driver for DM644X SoC
This is the display driver for Texas Instruments's DM644X family
SoC. This patch contains the main implementation of the driver with the
V4L2 interface. The driver implements the streaming model with
support for both kernel allocated buffers and user pointers. It also
implements all of the necessary IOCTLs necessary and supported by the
video display device.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:09 -03:00
Jiri Slaby 9a78efc8fb [media] DVB: dvb-net, make the kconfig text helpful
Telling the user they can disable an option if they want is not the
much useful. Describe what it is good for instead.

The text was derived from Mauro's email.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Hans Petter Selasky <hselasky@c2i.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:09 -03:00
Greg Dietsche 3735edf9fd [media] dvb: remove unnecessary code
remove unnecessary code that matches this coccinelle pattern
	if (...)
		return ret;
	return ret;

Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:09 -03:00
Tejun Heo fe45e2551f [media] dvb-usb/technisat-usb2: don't use flush_scheduled_work()
flush_scheduled_work() is deprecated and scheduled to be removed.
technisat-usb2 already sync-cancels the only work item it uses and
there's no reason for it to call flush_scheduled_work().  Don't use
it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:08 -03:00
Guennadi Liakhovetski 8c528d5e51 [media] media: DVB_NET must depend on DVB_CORE
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:07 -03:00
Andy Walls 9b3d8eccc3 [media] cx23885: Add IR Rx support for HVR-1270 boards
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:06 -03:00
Peter Moon de8ae0d516 [media] cx231xx: Add support for Hauppauge WinTV USB2-FM
This patch adds support for the "Hauppauge WinTV USB2-FM" Analog TV Stick.
It includes support for both the PAL and NTSC variants of the device.

Signed-off-by: Peter Moon <pomoon@gmail.com>
Reviewed-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:06 -03:00
Justin P. Mattock c3f305aab4 [media] frontends/s5h1420: Change: clock_settting to clock_setting
Changes clock_settting to clock_setting.

Note: This could be intentionally set this way from the beginning and/or
is a typo.

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:05 -03:00
istvan_v@mailbox.hu 79a5b9a2d9 [media] cx88: replaced duplicated code with function call
The following patch replaces code to reset the XC3028 tuner with a call
to the tuner reset callback.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:05 -03:00
istvan_v@mailbox.hu 8eb79c0b9b [media] cx88: added support for Leadtek WinFast DTV1800 H with XC4000 tuner
This patch implements support for the Leadtek WinFast DTV1800 H card with
XC4000 tuner (107d:6f38).

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:05 -03:00
istvan_v@mailbox.hu f271a3affa [media] cx88: added support for Leadtek WinFast DTV2000 H Plus
This patch implements support for the Leadtek WinFast DTV2000 H Plus card
with XC4000 tuner (107d:6f42).

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:05 -03:00
istvan_v@mailbox.hu c21973e8aa [media] cx88: added XC4000 tuner callback and DVB attach functions
Added functions for XC4000 tuner reset and attaching DVB frontend.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:04 -03:00
Mauro Carvalho Chehab 0db15d525d [media] em28xx: Mark Kworld 305 as validated
This board were used for testing the em28xx-alsa using a separate interface.
So, it is obviously validated ;)

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:04 -03:00
Mauro Carvalho Chehab 4f83e7b3ef [media] em28xx: Add support for devices with a separate audio interface
Some devices use a separate interface for the vendor audio class.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:04 -03:00
Mauro Carvalho Chehab dff0f8c279 [media] em28xx-audio: Some Alsa API fixes
Mark the alsa stream with SNDRV_PCM_INFO_BATCH,
as the timing to get audio streams can vary.

Also, add SNDRV_PCM_TRIGGER for pause/release.

while here, fix the stop indicator, to be sure that audio
will be properly released at the stop events.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:04 -03:00
Mauro Carvalho Chehab debb724149 [media] em28xx-audio: Properly report failures to start stream
If the audio stream fails for any reason, it should:
	1) Report an error via dmesg;
	2) Mark internally that the stream didn't started.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:04 -03:00
Mauro Carvalho Chehab 66cb6957d3 [media] em28xx-audio: add debug info for the volume control
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:04 -03:00
Mauro Carvalho Chehab 71d7d83edc [media] em28xx-audio: volumes are inverted
While here, fix volume mask to 5 bits

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:03 -03:00
Mauro Carvalho Chehab 43131a2ca6 [media] em28xx-audio: add support for mute controls
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:03 -03:00
Mauro Carvalho Chehab 850d24a5a8 [media] em28xx-alsa: add mixer support for AC97 volume controls
Export ac97 volume controls via mixer.

Pulseaudio will probably handle it very badly, as it has
no idea about how volumes are wired, and how are they
associated with each TV input. Those wirings are
card model dependent, and we don't have the wiring mappings
for each supported device.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:03 -03:00
Mauro Carvalho Chehab 5b89ecf989 [media] em28xx: Allow to compile it without RC/input support
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:03 -03:00
Mauro Carvalho Chehab 0f8a61fc42 [media] em28xx: Fix a wrong enum at the ac97 control tables
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:03 -03:00
Mauro Carvalho Chehab 00d2e7ad9d [media] em28xx: Don't initialize a var if won't be using it
Fixes most cases of initializing a var but not using it.

There are still 3 cases at em28xx-alsa, were those vars should
probably be used.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:02 -03:00
Jonathan Corbet 67a8dbbc4e [media] marvell-cam: Basic working MMP camera driver
Now we have a camera working over the marvell cam controller core.  It
works like the cafe driver and has all the same limitations, contiguous DMA
only being one of them.  But it's a start.

Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:01 -03:00
Jonathan Corbet 595a93a47a [media] marvell-cam: Allocate the i2c adapter in the platform driver
The upcoming mmp-camera driver will need an i2c_adapter structure allocated
externally, so change the core adapter to a pointer and require the
platform code to fill it in.

Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:01 -03:00
Jonathan Corbet 1c68f889c3 [media] marvell-cam: Right-shift i2c slave ID's in the cafe driver
This makes the cafe i2c implement consistent with the rest of Linux so that
the core can use the same slave ID everywhere.

Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:00 -03:00
Jonathan Corbet f8ff6a96cd [media] marvell-cam: Move Cafe-specific register definitions to cafe-driver.c
Nobody else ever needs to see these, so let's hide them.

Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:00 -03:00
Jonathan Corbet 9eefa7dc01 [media] marvell-cam: Remove the "untested" comment
This code is, indeed, tested :)

Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:00 -03:00
Jonathan Corbet 2164b5af1d [media] marvell-cam: Pass sensor parameters from the platform
Depending on the controller, the ov7670 sensor may be told to work with a
different clock speed or to use the SMBUS protocol.  Remove the wired-in
code and pass that information from the platform layer.  The Cafe driver
now just assumes it's running on an OLPC XO 1; I do not believe it has ever
run anywhere else.

Cc: Daniel Drake <dsd@laptop.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:00 -03:00
Jonathan Corbet abfa3df36c [media] marvell-cam: Separate out the Marvell camera core
There will eventually be multiple users of the core camera controller, so
separate it from the bus/platform/i2c stuff.  I've tried to do the minimal
set of changes to get the driver functioning in this configuration; I did
clean up a bunch of old checkpatch gripes in the process.  This driver
works like the old one did on OLPC XO 1 systems.

Cc: Daniel Drake <dsd@laptop.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:00 -03:00
Jonathan Corbet f8fc729870 [media] marvell-cam: Move cafe-ccic into its own directory
This driver will soon become a family of drivers, so let's give it its own
place to live.  This move requires putting ov7670.h into include/media, but
there are no code changes.

Cc: Daniel Drake <dsd@laptop.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:53:00 -03:00
Andre Bartke 2c87d9db46 [media] drivers/media/video: fix memory leak of snd_cx18_init()
cxsc is not freed in the error case.

Signed-off-by: Andre Bartke <andre.bartke@gmail.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:59 -03:00
Hans Petter Selasky 7ce338d9df [media] Correct and add some parameter descriptions
>From 70d02ce19f64fae4ceee563501e8462a76e17b91 Mon Sep 17 00:00:00 2001

Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:59 -03:00
Hans Petter Selasky ed5d11d592 [media] Remove unused definitions which can cause conflict with definitions in usb/ch9.h
>From 0dd2949dfeae431ed4ffbd00fd14a10dc3747ad0 Mon Sep 17 00:00:00 2001

Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:59 -03:00
Hans Petter Selasky 2c7988ab0e [media] Correct error code from -ENOMEM to -EINVAL.
Make sure the return value is set in all cases

>From 9b38a5c9878b5e4be2899ae291c4524f5f5fc218 Mon Sep 17 00:00:00 2001

Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:59 -03:00
David Härdeman 5588dc2b02 [media] rc-core: lirc use unsigned int
Durations can never be negative, so it makes sense to consistently use
unsigned int for LIRC transmission. Contrary to the initial impression,
this shouldn't actually change the userspace API.

Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:59 -03:00
Sensoray Linux Development 8a8cc952d3 [media] s2255drv: firmware version update, vendor request change
removes obsolete comments. updates firmware versions. firmware vendor request simplified.

Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:58 -03:00
Mauro Carvalho Chehab 941830c927 [media] xc4000: make checkpatch.pl happy
Solve the ./scripts/checkpatch.pl compliants for the patches
that added xc4000 support, including a few changes at dib0700.

While here, remove a few printk noise by converting some msgs
into debug ones.

Cc: Istvan Varga <istvan_v@mailbox.hu>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:40 -03:00
istvan_v@mailbox.hu 8edeb6eb1a [media] xc4000: removed card_type
Removed the use of 'card_type' from the tuner configuration structure, and
replaced it with separate parameters to set board-specific configuration.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:40 -03:00
istvan_v@mailbox.hu 09f4634293 [media] xc4000: check firmware version
Enabled code to check if the version of the firmware reported by the hardware
is correct after uploading it.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:40 -03:00
istvan_v@mailbox.hu 7c8ec47a92 [media] dvb-usb/Kconfig: auto-select XC4000 tuner for dib0700
Automatically select the xc4000 module for dib0700 if the tuner selection is
not customized.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:40 -03:00
istvan_v@mailbox.hu 341747bef5 [media] xc4000: code cleanup
Various coding style changes:
  - removed unused / commented out code
  - changed C++ style comments to C format
  - renamed functions and variables that included upper case letters in the name
  - removed tabs from module parameter descriptions
  - replaced the use of XC_RESULT_* with standard error codes

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:40 -03:00
Istvan Varga 7db98fe66b [media] xc4000: detect also xc4100
Added code to detect the XC4100 chip, which is presumably an analog-only
"value" version of the XC4000. It is not sure, however, if any devices
using this have actually been produced and sold, so the patch may be
unneeded.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:39 -03:00
Istvan Varga 8f76afe8d7 [media] xc4000: removed redundant tuner reset
This patch causes the tuner reset command to be ignored in the firmware
code, since this only happens when the BASE/INIT1 firmware is loaded by
check_firmware(), and in that case check_firmware() already calls the
reset callback before starting to load the firmware.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:39 -03:00
Istvan Varga e75873c1f8 [media] xc4000: xc_tune_channel() cleanup
Minor coding changes related to the xc_tune_channel() function.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:39 -03:00
Istvan Varga 818a1776a4 [media] xc4000: implemented analog TV and radio
The following patch implements support for analog TV and FM radio.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:39 -03:00
Istvan Varga 923137a403 [media] xc4000: added audio_std module parameter
The 'audio_std' module parameter makes it possible to fine tune
some audio related aspects of the driver, like setting the exact
audio standard (NICAM, A2, etc.) to be used for some video standards.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:39 -03:00
Istvan Varga 30f544ec56 [media] xc4000: setting registers
This patch implements setting the registers in xc4000_set_params()
and xc4000_set_analog_params(). A new register is defined which enables
filtering of the composite video output (this is needed to avoid bad
picture quality with some boards).

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:38 -03:00
Istvan Varga f4312e2fd4 [media] xc4000: debug message improvements
The following patch makes a few minor changes to the printing
of debug messages, and reporting the tuner status. The 'debug'
module parameter can now be set from 0 to 2 to control the
verbosity of debug messages.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:38 -03:00
Istvan Varga 027fd36186 [media] xc4000: firmware initialization
This patch fixes/cleans up the loading of the firmware file when the
driver is loaded and initialized.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:36 -03:00
Istvan Varga 5272f6b1f4 [media] xc4000: implemented power management
The following patch implements the xc4000_sleep() function.
The 'no_powerdown' module parameter is now interpreted differently:
  - 0 uses a device-specific default
  - 1 disables power management like before
  - 2 enables power management

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:36 -03:00
Istvan Varga 0b4021321c [media] xc4000: added card_type
This patch adds support for selecting a card type in struct
xc4000_config, to allow for implementing some card specific code
in the driver.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:36 -03:00
Istvan Varga 595a83f49a [media] xc4000: check_firmware() cleanup
This patch makes the following fixes in check_firmware():
  - there is only one BASE and INIT1 firmware for XC4000
  - loading SCODE is needed also for FM radio

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:36 -03:00
Istvan Varga ffce6266c8 [media] xc4000: simplified load_scode
Removed unused code from load_scode() (all SCODE firmwares are
assumed to have the HAS_IF bit set).

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:34 -03:00
Istvan Varga 3db9570482 [media] xc4000: simplified seek_firmware()
This patch simplifies the code in seek_firmware().

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:34 -03:00
Istvan Varga fa285bc1bf [media] xc4000: added firmware_name parameter
The firmware_name module parameter makes it possible to set the firmware
file name. It defaults to "xc4000.fw" if not specified.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:34 -03:00
Istvan Varga 1368ceb266 [media] xc4000: fixed frequency error
The xc_get_frequency_error() function reported the frequency error
incorrectly. The data read from the hardware is a signed integer, in
15625 Hz units. The attached patch fixes the bug.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:34 -03:00
Istvan Varga 5614942bb0 [media] xc4000: added mutex
This patch adds a mutex to xc4000_priv, to protect the driver
from being accessed by multiple processes at the same time.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:34 -03:00
Istvan Varga f0ef7c88ca [media] xc4000: added support for 7 MHz DVB-T
The following patch implements support for DVB-T with 7 MHz bandwidth.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:34 -03:00
Istvan Varga 4911085fa3 [media] xc4000: updated standards table
This patch makes the following changes to the standards table:
  - added 'u16 int_freq' to struct XC_TV_STANDARD (needed for analog TV
    and radio, 0 for DVB-T)
  - added new standard for SECAM-D/K video with PAL-D/K audio
  - the 'int_freq' values are now specified in the table
  - changed VideoMode for NTSC and PAL-B/G standards

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:33 -03:00
Istvan Varga fbe4a29f2f [media] xc4000: code cleanup
This is the first of a set of patches that update the original xc4000
sources to my modified version. It removes some unused code, and makes
a few minor formatting changes.

[mchehab@redhat.com: re-add XC_TUNE_ANALOG/XC_TUNE_DIGITAL constants, to avoid compilation breakage]
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:33 -03:00
Mauro Carvalho Chehab e3bb7c607f [media] xc4000: Fix a few bad whitespaces on it
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:33 -03:00
Devin Heitmueller 62956cedb5 [media] dib0700: remove notes from bringup of PCTV 340e
Remove some inline comments I had written from when I was computing the proper
dib7000p configuration to work with the xc4000.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:33 -03:00
Devin Heitmueller b6cdb5bea3 [media] xc4000: cleanup dmesg logging
Remove some printk() calls added during driver development, and demote some
other messages to debug only (to reduce dmesg chatter).

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:33 -03:00
Devin Heitmueller 980029eb35 [media] xc4000: rename firmware image filename
Give the xc4000 firmware filename a filename that makes more sense for public
release.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:31 -03:00
Devin Heitmueller 4922cec59a [media] xc4000: turn off debug logging by default
Don't dump debug into to dmesg by default (something I had enabled during
bringup of the xc4000 driver).

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:31 -03:00
Devin Heitmueller 2df12510f9 [media] dib0700: make PCTV 340e work!
Fixup the PLL and AGC configs so that the 340e works (correcting errors I made
when I did the original config blindly).

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:31 -03:00
Devin Heitmueller ed23db3227 [media] xc4000: get rid of hard-coded 8MHz firmware config
Remove a hack I had put in to force the firmware to be 8MHz, now setting
the firmware properly based on the target standard.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:31 -03:00
Devin Heitmueller f1c78d340f [media] dib0700: fixup PLL config for PCTV 340e
Based on a reference trace under Windows, reverse engineer the PLL config.
Note that the xtal is not yet setup, and the timf cannot be determined yet
because my reference trace doesn't actually achieve a signal lock.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:30 -03:00
Devin Heitmueller 799ed11afe [media] xc4000: handle dib0700 broken i2c stretching
It was confirmed by DibCom that i2c stretching is broken in the i2c master
on the dib7700.  So we need to put a hack into the xc4000 driver to not
complain in certain very specific cases where we know i2c stretching occurs.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:30 -03:00
Devin Heitmueller 8583fc834e [media] xc4000: setup dib7000p AGC config for PCTV 340e
Setup a proper AGC config for the 340e, based on the Windows USB trace

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:30 -03:00
Devin Heitmueller fe83036476 [media] xc4000: use if_khz provided in xc4000_config
Remove hard-coded references to 5400, using the value passed in when the
xc4000 is attached.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:30 -03:00
Devin Heitmueller ee4c3cd67b [media] xc4000: continued cleanup of the firmware loading routine
Properly setup the standard firmware loading and scode loading, as well as
getting rid of a ton of dead code.  Note that I am getting a single i2c
error when the standard firmware sets the video standard, but everything else
seems to be loading properly now.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:29 -03:00
Devin Heitmueller d0962382cf [media] xc4000: add code to do standard and scode firmware loading
Add code to handle firmware blobs for the standard and scode.  Note there
appears to be some issue with loading the DTV8 standard firmware, probably
related to direct/indirect mode.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:29 -03:00
Devin Heitmueller e7490d5962 [media] xc4000: remove xc5000 firmware loading routine
Since we use the xc3028 version of the firmware file parsing routine (which
includes support for scodes and separate blobs), we can drop the xc5000
version of the code.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:29 -03:00
Devin Heitmueller 02dec50982 [media] xc4000: remove XREG_BUSY code only supported in xc5000
The xc4000 driver is based on the original xc5000 driver, and while the
xc5000 supports the XREG_BUSY register, the xc4000 does not.  So remove the
code in question.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:29 -03:00
Devin Heitmueller 6bf60d56b3 [media] xc4000: properly set type for init1 firmware
We need to set the firmware type properly in order to locate the init1
firmware.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:28 -03:00
Devin Heitmueller 31f880e2b9 [media] xc4000: cut over to using xc5000 version for loading i2c sequences
The xc3028 version does i2c splitting in a different manner than xc4000 and
xc5000, so reuse the xc5000 version of the routine (the key here being that
xc4000 expects the first *two* bytes to be the same for splitting transactions.

Doing it the xc3028 way was resulting in i2c errors partially through the
firmware load.  With this change, it would appear that the entire base firmware
is being loaded successfully (product id now properly shows 0x0FA0).

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:28 -03:00
Devin Heitmueller 11091a31fb [media] xc4000: pull in firmware management code from xc3028
Switch over to using the firmware management routines from the tuner-xc2028,
since that has support for scodes, etc.

This code still requires signficant cleanup, and at this point the base
firmware does not load properly (i2c write errors about 300 bytes in).

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:28 -03:00
Devin Heitmueller 85ec9d7193 [media] dib7000p: setup dev.parent for i2c master built into 7000p
We need to set the dev.parent member on the dib7000p on its i2c master, or
else calls to request_firmware() will hit an oops in 2.6.31.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:28 -03:00
Devin Heitmueller 2750d9c3af [media] dib0700: add a sleep before attempting to detect dib7000p
Add a sleep since in some cases the dib7000p wasn't online when being probed.
The optimal timing has not yet been determined.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:27 -03:00
Devin Heitmueller 59d0c37baa [media] dib0700: successfully connect to xc4000 over i2c for PCTV 340e
Use the correct i2c bus to communicate with the tuner, and properly setup the
reset GPIO and i2c address.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:26 -03:00
Devin Heitmueller 01f16263ad [media] dib0700: properly setup GPIOs for PCTV 340e
Provide a frontend setup routine for the PCTV 340e which takes into account
the specific GPIO setup of the board.

Note that this patch does *not* take into account the xc4000 reset pin, which
is attached to the dib7000.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:26 -03:00
Devin Heitmueller 33fb1681c6 [media] dib0700: add USB id for PCTV 340eSE
Add the board profile for the PCTV 340eSE, since that's what I have here
for development.

[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:26 -03:00
Davide Ferri 8d009a0c41 [media] dib0700: add initial code for PCTV 340e by Davide Ferri
This is initial code written by Davide Ferri for the PCTV 340e, including
a new xc4000 driver.  I am checking in all the code unmodified, and making
no assertions about its quality (other than confirming it compiles).

[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Davide Ferri <davidef1986@gmail.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:25 -03:00
Johannes Obermaier 32127363ee [media] mt9v011: Fixed gain calculation
The implementation of the gain calculation for this sensor is incorrect.
It is only working for the first 127 values.

The reason is, that the gain cannot be set directly by writing a value
into the gain registers of the sensor. The gain register work this way
(see datasheet page 24): bits 0 to 6 are called "initial gain". These
are linear. But bits 7 and 8 ("analog multiplicative factors") and bits
9 and 10 ("digital multiplicative factors") work completely different:
Each of these bits increase the gain by the factor 2. So if the bits
7-10 are 0011, 0110, 1100 or 0101 for example, the gain from bits 0-6 is
multiplied by 4. The order of the bits 7-10 is not important for the
resulting gain. (But there are some recommended values for low noise)

The current driver doesn't do this correctly: If the current gain is 000
0111 1111 (127) and the gain is increased by 1, you would expect the
image to become brighter. But the image is completly dark, because the
new gain is 000 1000 0000 (128). This means: Initial gain of 0,
multiplied by 2. The result is 0.

This patch adds a new function which does the gain calculation and also
fixes the same bug for red_balance and blue_balance. Additionally, the
driver follows the recommendation from the datasheet, which says, that
the gain should always be above 0x0020.

Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Johannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:25 -03:00
Johannes Obermaier 590929f32a [media] mt9v011: Added exposure for mt9v011
There are problems when you use this camera/sensor in a very bright room
or outside. The image is completely white, because it is overexposed.
The driver uses a default value which is not suitable for all
environments.

This patch makes it possible to adjust the exposure time by youself. I
found out by logging the i2c-data, that the windows driver for this
sensor is doing this, too. I tested the camera on a sunny day and after
adjusting the exposure time, I was able to see a very good image.

Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Johannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:25 -03:00
Johannes Obermaier 1048af2f81 [media] mt9v011: Fixed incorrect value for the first valid column
According to the datasheet (page 8), the first optical clear
pixel-column is not at position 14. The correct/recommended value is 20.
Without this patch there is a dark line on the left side of the image.

Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Johannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:25 -03:00
David Härdeman b87f2eddfa [media] rc-core: fix winbond-cir issues
The conversion of winbond-cir to use rc-core seems to have missed a
a few bits and pieces which were in my local tree. Kudos to
Juan Jesús García de Soria Lucena <skandalfo@gmail.com> for noticing.

[mchehab@redhat.com: fix two UTF-8 violations]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:24 -03:00
Dan Carpenter 7eb7571546 [media] rc/redrat3: dereferencing null pointer
In the original code, if the allocation failed we dereference "rr3"
when it was NULL.

Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:24 -03:00
Dan Carpenter 0528f354cf [media] rc: double unlock in rc_register_device()
If change_protocol() fails and we goto out_raw, then it calls unlock
twice.  I noticed that the other time we called change_protocol() we
held the &dev->lock, so I changed it to hold it here too.

Reviewed-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:24 -03:00
Andreas Oberritter ec05a64214 [media] DVB: dvb_frontend: fix dtv_property_dump for DTV_DVBT2_PLP_ID
- Add missing entry to array "dtv_cmds".
- Set array size to DTV_MAX_COMMAND + 1 to avoid future off-by-ones.

Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:24 -03:00
Uwe Kleine-König 7f116b3ea9 [media] V4L/videobuf2-memops: use pr_debug for debug messages
Otherwise they clutter the dmesg buffer even on a production kernel.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:23 -03:00
Manoel Pinheiro 147b68cd7e [media] dvb-usb.h function rc5_scan
The function "rc5_scan" in "dvb_usb.h" is returning invalid value.
The value should be returned "u16" but is returning "u8".

See example below in "drivers/media/dvb/dvb-usb/opera1.c":

        send_key = (send_key & 0xffff) | 0x0100;

        for (i = 0; i < ARRAY_SIZE(rc_map_opera1_table); i++) {
            if (rc5_scan(&rc_map_opera1_table[i]) == (send_key & 0xffff)) {
                *state = REMOTE_KEY_PRESSED;
                *event = rc_map_opera1_table[i].keycode;
                opst->last_key_pressed =
                    rc_map_opera1_table[i].keycode;
                break;
            }
            opst->last_key_pressed = 0;
        }

Signed-off-by: Manoel Pinheiro <pinusdtv@hotmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:23 -03:00
Ondrej Zary 9e8fa0e644 [media] radio-sf16fmr2: convert to generic TEA575x interface
Convert radio-sf16fmr2 to use generic TEA575x implementation. Most of the
driver code goes away as SF16-FMR2 is basically just a TEA5757 tuner
connected to ISA bus.
The card can optionally be equipped with PT2254A volume control (equivalent
of TC9154AP) - the volume setting is completely reworked (with balance control
added) and tested.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:23 -03:00
Hans Petter Selasky d294093010 [media] cx24113: Don't reuse core macro names
The info and err macros are already defined by the USB stack. Rename
these macros to avoid macro redefinition warnings.

Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:22 -03:00
Hans Petter Selasky a5bef1d252 [media] itd1000: Don't reuse core macro names
The dbg, warn and info macros are already defined by the USB stack.
Rename these macros to avoid macro redefinition warnings.

Refactor lineshift in printouts.

Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:21 -03:00
Alexey Khoroshilov f54ba7f199 [media] radio-si470x: fix memory leak in si470x_usb_driver_probe()
radio->int_in_urb is not deallocated on error paths in si470x_usb_driver_probe().

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:21 -03:00
Joe Perches fabc6b85ca [media] media: Convert vmalloc/memset to vzalloc
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:21 -03:00
Mauro Carvalho Chehab fcc8e7d8c0 dvb_net: Simplify the code if DVB NET is not defined
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:20 -03:00
Hans Petter Selasky a34ff6cdbb [media] Make DVB NET configurable in the kernel
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:20 -03:00
Hans Petter Selasky 2ef4037088 [media] Fix compile warning: Dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:20 -03:00
Newson Edouard 45f239ab82 [media] videobuf_pages_to_sg: sglist[0] length problem
On function videobuf_pages_to_sg the statement sg_set_page(&sglist[0],
pages[0], PAGE_SIZE - offset, offset) will fail if size is less than
PAGE_SIZE.

Signed-off-by: Newson Edouard <newsondev@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:19 -03:00
Tejun Heo 4bbcd849b0 [media] cx23885: restore flushes of cx23885_dev work items
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:18 -03:00
Dan Carpenter 061d55eb45 [media] saa7164: poll mask set incorrectly
list_first_entry() always returns non-null here.  I think the intent was
to test whether there were any entries in the used list.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:18 -03:00
Antti Palosaari 050bf0faa8 [media] cxd2820r: correct missing error checks
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:17 -03:00
Mauro Carvalho Chehab ebaefdb765 [media] em28xx: use the proper prefix for board names
All boards use EM28xxx_BOARD, to identify that the macro
refers to a card entry. So:

EM2874_LEADERSHIP_ISDBT -> EM2874_BOARD_LEADERSHIP_ISDBT

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:16 -03:00
Antti Palosaari 460312ec5a [media] em28xx: correct PCTV nanoStick T2 290e device name
PCTV Systems nanoStick T2 290e => PCTV nanoStick T2 290e

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:15 -03:00
Antti Palosaari ff7b929f04 [media] em28xx: add remote for PCTV nanoStick T2 290e
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:14 -03:00
Antti Palosaari a24ec44801 [media] em28xx: EM28174 remote support
For some reason it repeats rather slowly, around 800ms intervals,
two RC5 remotes tested.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:14 -03:00
Antti Palosaari 1d44ccb9ea [media] cxd2820r: fix bitfields
error: dubious one-bit signed bitfield

Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:10 -03:00
Antti Palosaari d838f4c318 [media] cxd2820r: malloc buffers instead of stack
kmalloc I2C buffers

Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:09 -03:00
Antti Palosaari 05c46c05d2 [media] anysee: style issues, comments, etc
Change some info, comments, variables. No functionality changes.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:09 -03:00
Antti Palosaari fea3c39a2e [media] anysee: add support for Anysee E7 PS2
Basically it is just same device as Anysee E7 S2 but made for
internal PCI(e) slot and motherboard USB connector.

Cc: info@anysee.com
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:07 -03:00
Antti Palosaari 8439e0df9c [media] anysee: add support for Anysee E7 PTC
Basically it is just same device as Anysee E7 TC but made for
internal PCI(e) slot and motherboard USB connector.

Cc: info@anysee.com
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:07 -03:00
Jean-François Moine 798ae1501d [media] gspca - ov519: New sensor ov9600 with bridge ovfx2
This sensor was found in a webcam 8020:ef04 (SVC - SVU2-1.3MV PCCam).

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-27 17:52:06 -03:00
Arun Sharma 60063497a9 atomic: use <linux/atomic.h>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>

Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-07-26 16:49:47 -07:00
Linus Torvalds d3ec4844d4 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
  fs: Merge split strings
  treewide: fix potentially dangerous trailing ';' in #defined values/expressions
  uwb: Fix misspelling of neighbourhood in comment
  net, netfilter: Remove redundant goto in ebt_ulog_packet
  trivial: don't touch files that are removed in the staging tree
  lib/vsprintf: replace link to Draft by final RFC number
  doc: Kconfig: `to be' -> `be'
  doc: Kconfig: Typo: square -> squared
  doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
  drivers/net: static should be at beginning of declaration
  drivers/media: static should be at beginning of declaration
  drivers/i2c: static should be at beginning of declaration
  XTENSA: static should be at beginning of declaration
  SH: static should be at beginning of declaration
  MIPS: static should be at beginning of declaration
  ARM: static should be at beginning of declaration
  rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
  Update my e-mail address
  PCIe ASPM: forcedly -> forcibly
  gma500: push through device driver tree
  ...

Fix up trivial conflicts:
 - arch/arm/mach-ep93xx/dma-m2p.c (deleted)
 - drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
 - drivers/net/r8169.c (just context changes)
2011-07-25 13:56:39 -07:00
David S. Miller 033b1142f4 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	net/bluetooth/l2cap_core.c
2011-07-21 13:38:42 -07:00
Mauro Carvalho Chehab dc6b845044 si4713-i2c: avoid potential buffer overflow on si4713
While compiling it with Fedora 15, I noticed this issue:

  inlined from ‘si4713_write_econtrol_string’ at drivers/media/radio/si4713-i2c.c:1065:24:
  arch/x86/include/asm/uaccess_32.h:211:26: error: call to ‘copy_from_user_overflow’ declared with attribute error: copy_from_user() buffer size is not provably correct

Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Eugene Teo <eugeneteo@kernel.sg>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-07-18 09:12:21 -07:00
Linus Torvalds 54a772b8aa Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  [media] tuner-core: fix a 2.6.39 regression with mt20xx
  [media] dvb_frontend: fix race condition in stopping/starting frontend
  [media] media: fix radio-sf16fmr2 build when SND is not enabled
  [media] MEDIA: Fix non-ISA_DMA_API link failure of sound code
  [media] nuvoton-cir: make idle timeout more sane
  [media] mceusb: increase default timeout to 100ms
  [media] mceusb: Timeout unit corrections
  [media] Revert "V4L/DVB: cx23885: Enable Message Signaled Interrupts(MSI)"
2011-07-17 12:48:18 -07:00
David S. Miller 6a7ebdf2fd Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	net/bluetooth/l2cap_core.c
2011-07-14 07:56:40 -07:00
Mauro Carvalho Chehab a1ad5ec7f5 [media] tuner-core: fix a 2.6.39 regression with mt20xx
As Simon reported, digital TV broke with mt20xx tuner due to
commit ad020dc2fe.

The mt20xx tuner passes V4L2_TUNER_DIGITAL_TV to tuner core. However, the
check_mode code now doesn't handle it well. Change the logic there to
avoid the breakage, and fix a test for analog-only at g_tuner.

Reported-by: Simon Arlott <simon@fire.lp0.eu>
Tested-by: Simon Arlott <simon@fire.lp0.eu>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-13 20:21:00 -03:00
Devin Heitmueller 2d1969312d [media] dvb_frontend: fix race condition in stopping/starting frontend
Attached is a patch which addresses a race condition in the DVB core
related to closing/reopening the DVB frontend device in quick
succession.  This is the reason that devices such as the HVR-1300,
HVR-3000, and HVR-4000 have been failing to scan properly under MythTV
and w_scan.

The gory details of the race are described in the patch.

Devin

There is a race condition exhibited when channel scanners such as w_scan and
MythTV quickly close and then reopen the frontend device node.

Under normal conditions, the behavior is as follows:

1.  Application closes the device node
2.  DVB frontend ioctl calls dvb_frontend_release which sets
    fepriv->release_jiffies
3.  DVB frontend thread *eventually* calls dvb_frontend_is_exiting() which
    compares fepriv->release_jiffies, and shuts down the thread if timeout has
    expired
4.  Thread goes away
5.  Application opens frontend device
6.  DVB frontend ioctl() calls ts_bus_ctrl(1)
7.  DVB frontend ioctl() creates new frontend thread, which calls
    dvb_frontend_init(), which has demod driver init() routine setup initial
    register state for demod chip.
8.  Tuning request is issued.

The race occurs when the application in step 5 performs the new open() call
before the frontend thread is shutdown.  In this case the ts_bus_ctrl() call
is made, which strobes the RESET pin on the demodulator, but the
dvb_frontend_init() function never gets called because the frontend thread
hasn't gone away yet.  As a result, the initial register config for the demod
is *never* setup, causing subsequent tuning requests to fail.

If there is time between the close and open (enough for the dvb frontend
thread to be torn down), then in that case the new frontend thread is created
and thus the dvb_frontend_init() function does get called.

The fix is to set the flag which forces reinitialization if we did in fact
call ts_bus_ctrl().

This problem has been seen on the HVR-1300, HVR-3000, and HVR-4000, and is
likely occuring on other designs as well where ts_bus_ctrl() actually strobes
the reset pin on the demodulator.

Note that this patch should supercede any patches submitted for the
1300/3000/4000 which remove the code that removes GPIO code in
cx8802_dvb_advise_acquire(), which have been circulating by users for some
time now...

Canonical tracking this issue in Launchpad 439163:

Thanks to Jon Sayers from Hauppauge and Florent Audebert from Anevia S.A. for
providing hardware to test/debug with.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Jon Sayers <j.sayers@hauppauge.co.uk>
Cc: Florent Audebert <florent.audebert@anevia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-13 19:50:12 -03:00
Randy Dunlap 42a741dcf1 [media] media: fix radio-sf16fmr2 build when SND is not enabled
When CONFIG_SND is not enabled, radio-sf16fmr2 build fails with:

so make this driver depend on SND.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: linux-media@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-13 19:40:08 -03:00
Ralf Baechle 4756fc64ec [media] MEDIA: Fix non-ISA_DMA_API link failure of sound code
sound/isa/es18xx.c: In function ‘snd_es18xx_playback1_prepare’:
sound/isa/es18xx.c:501:9: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/es18xx.c: In function ‘snd_es18xx_playback_pointer’:
sound/isa/es18xx.c:818:3: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[2]: *** [sound/isa/es18xx.o] Error 1
sound/isa/sscape.c: In function ‘upload_dma_data’:
sound/isa/sscape.c:481:3: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[2]: *** [sound/isa/sscape.o] Error 1
sound/isa/ad1816a/ad1816a_lib.c: In function ‘snd_ad1816a_playback_prepare’:
sound/isa/ad1816a/ad1816a_lib.c:244:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/ad1816a/ad1816a_lib.c: In function ‘snd_ad1816a_playback_pointer’:
sound/isa/ad1816a/ad1816a_lib.c:302:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
sound/isa/ad1816a/ad1816a_lib.c: In function ‘snd_ad1816a_free’:
sound/isa/ad1816a/ad1816a_lib.c:544:3: error: implicit declaration of function ‘snd_dma_disable’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/ad1816a/ad1816a_lib.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/ad1816a] Error 2
sound/isa/es1688/es1688_lib.c: In function ‘snd_es1688_playback_prepare’:
sound/isa/es1688/es1688_lib.c:417:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/es1688/es1688_lib.c: In function ‘snd_es1688_playback_pointer’:
sound/isa/es1688/es1688_lib.c:509:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/es1688/es1688_lib.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/es1688] Error 2
sound/isa/gus/gus_dma.c: In function ‘snd_gf1_dma_program’:
sound/isa/gus/gus_dma.c:79:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/gus/gus_dma.c: In function ‘snd_gf1_dma_done’:
sound/isa/gus/gus_dma.c:177:3: error: implicit declaration of function ‘snd_dma_disable’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/gus/gus_dma.o] Error 1
sound/isa/gus/gus_pcm.c: In function ‘snd_gf1_pcm_capture_prepare’:
sound/isa/gus/gus_pcm.c:591:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/gus/gus_pcm.c: In function ‘snd_gf1_pcm_capture_pointer’:
sound/isa/gus/gus_pcm.c:619:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/gus/gus_pcm.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/gus] Error 2
sound/isa/sb/sb16_csp.c: In function ‘snd_sb_csp_ioctl’:
sound/isa/sb/sb16_csp.c:228:227: error: case label does not reduce to an integer constant
make[3]: *** [sound/isa/sb/sb16_csp.o] Error 1
sound/isa/sb/sb16_main.c: In function ‘snd_sb16_playback_prepare’:
sound/isa/sb/sb16_main.c:276:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/sb/sb16_main.c: In function ‘snd_sb16_playback_pointer’:
sound/isa/sb/sb16_main.c:456:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/sb/sb16_main.o] Error 1
sound/isa/sb/sb8_main.c: In function ‘snd_sb8_playback_prepare’:
sound/isa/sb/sb8_main.c:172:3: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/sb/sb8_main.c: In function ‘snd_sb8_playback_pointer’:
sound/isa/sb/sb8_main.c:425:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/sb/sb8_main.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/sb] Error 2
sound/isa/wss/wss_lib.c: In function ‘snd_wss_playback_prepare’:
sound/isa/wss/wss_lib.c:1025:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/wss/wss_lib.c: In function ‘snd_wss_playback_pointer’:
sound/isa/wss/wss_lib.c:1160:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
sound/isa/wss/wss_lib.c: In function ‘snd_wss_free’:
sound/isa/wss/wss_lib.c:1695:3: error: implicit declaration of function ‘snd_dma_disable’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/wss/wss_lib.o] Error 1
warning: (RADIO_MIROPCM20) selects SND_ISA which has unmet direct dependencies (SOUND && !M68K && SND && ISA && ISA_DMA_API)

A build with ISA && ISA_DMA && !ISA_DMA_API results in:
  CC      sound/isa/es18xx.o
  CC      sound/isa/sscape.o
  CC      sound/isa/ad1816a/ad1816a_lib.o
  CC      sound/isa/es1688/es1688_lib.o
  CC      sound/isa/gus/gus_dma.o
  CC      sound/isa/gus/gus_pcm.o
  CC      sound/isa/sb/sb16_csp.o
  CC      sound/isa/sb/sb16_main.o
  CC      sound/isa/sb/sb8_main.o
  CC      sound/isa/wss/wss_lib.o

The root cause for this is hidden in this Kconfig warning:

Adding a dependency on ISA_DMA_API to RADIO_MIROPCM20 fixes these issues.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-13 01:35:31 -03:00
Jarod Wilson d7b290a105 [media] nuvoton-cir: make idle timeout more sane
The nuvoton-cir inherited an insanely low idle timeout value from the
mceusb driver. We're fixing mceusb, should fix this driver too.

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-11 20:52:37 -03:00
Rafi Rubin 9824ae4aff [media] mceusb: increase default timeout to 100ms
This matches the typical timeout advertised by hardware, once we're
actually interpreting it correctly.

Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-11 20:52:27 -03:00
Rafi Rubin f3e456cb89 [media] mceusb: Timeout unit corrections
Unit missmatch in mceusb_handle_command.  It should be converting to us,
not 1/10th of ms.

mceusb_dev_printdata 100us/ms -> 1000us/ms

Alter format of fix slightly and update comment to match proper reality.

Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-11 20:52:18 -03:00
Jarod Wilson d7515b8866 [media] Revert "V4L/DVB: cx23885: Enable Message Signaled Interrupts(MSI)"
This reverts commit e38030f3ff.

MSI flat-out doesn't work right on cx2388x devices yet. There are now
multiple reports of cards that hard-lock systems when MSI is enabled,
including my own HVR-1250 when trying to use its built-in IR receiver.
Disable MSI and it works just fine. Similar for another user's HVR-1270.
Issues have also been reported with the HVR-1850 when MSI is enabled,
and the 1850 behavior sounds similar to an as-yet-undiagnosed issue I've
seen with an 1800.

CC: stable@kernel.org
CC: Steven Toth <stoth@kernellabs.com>
CC: Kusanagi Kouichi <slash@ac.auone-net.jp>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-11 20:51:51 -03:00
Linus Torvalds c15000b40d Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  [media] msp3400: fill in v4l2_tuner based on vt->type field
  [media] tuner-core.c: don't change type field in g_tuner or g_frequency
  [media] cx18/ivtv: fix g_tuner support
  [media] tuner-core: power up tuner when called with s_power(1)
  [media] v4l2-ioctl.c: check for valid tuner type in S_HW_FREQ_SEEK
  [media] tuner-core: simplify the standard fixup
  [media] tuner-core/v4l2-subdev: document that the type field has to be filled in
  [media] v4l2-subdev.h: remove unused s_mode tuner op
  [media] feature-removal-schedule: change in how radio device nodes are handled
  [media] bttv: fix s_tuner for radio
  [media] pvrusb2: fix g/s_tuner support
  [media] v4l2-ioctl.c: prefill tuner type for g_frequency and g/s_tuner
  [media] tuner-core: fix tuner_resume: use t->mode instead of t->type
  [media] tuner-core: fix s_std and s_tuner
2011-07-11 16:43:27 -07:00
Jiri Kosina b7e9c223be Merge branch 'master' into for-next
Sync with Linus' tree to be able to apply pending patches that
are based on newer code already present upstream.
2011-07-11 14:15:55 +02:00
Jesper Juhl c172d82500 drivers/media: static should be at beginning of declaration
Make sure that the 'static' keywork is at the beginning of declaration
for drivers/media/video/omap/omap_vout.c

This gets rid of warnings like
  warning: ‘static’ is not at beginning of declaration
when building with -Wold-style-declaration (and/or -Wextra which also
enables it).

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-07-11 14:13:47 +02:00
Hans Verkuil ddc6ff31cc [media] msp3400: fill in v4l2_tuner based on vt->type field
The vt->type field determines how the msp3400 should fill in the
tuner data, not whether the msp3400 is in radio mode or not.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-07 17:28:30 -03:00
Hans Verkuil 5ad339a298 [media] tuner-core.c: don't change type field in g_tuner or g_frequency
The tuner core should not silently change the type field in g_tuner and
g_frequency. If the tuner is in a different mode than the one that was
requested, then just fill in what you can and don't attempt to read afc,
signal or rxsubchans values.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-07 17:20:04 -03:00
Hans Verkuil d118e294e2 [media] cx18/ivtv: fix g_tuner support
The driver shouldn't override vt->type, and the tuner name should be
based on vt->type as well.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-07 15:07:43 -03:00
Hans Verkuil d16625e788 [media] tuner-core: power up tuner when called with s_power(1)
Drivers must be able to rely on s_power to power up subdevices.

Note that at this moment no driver attempts to power up tuners. This probably
isn't surprising since s_power(1) was never implemented in tuner-core.c until
now.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-07 15:07:01 -03:00
Hans Verkuil a6cf90a915 [media] v4l2-ioctl.c: check for valid tuner type in S_HW_FREQ_SEEK
Prohibit attempts to change the tuner to a type that is different
from the device node the ioctl is called from. I.e. the type must
be RADIO for a radio node and ANALOG_TV for a video/vbi node.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-07 15:06:12 -03:00
Hans Verkuil 487833018e [media] tuner-core: simplify the standard fixup
Get rid of a number of unnecessary tuner_dbg messages by simplifying
the std fixup function.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-07 15:04:41 -03:00
Hans Verkuil 338e9e1ad5 [media] tuner-core/v4l2-subdev: document that the type field has to be filled in
The tuner ops g_frequency, g_tuner and s_tuner require that the tuner type
field is filled in. Document this.

The tuner-core doc is based on a patch from Mauro Carvalho Chehab <mchehab@redhat.com>.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-07 15:04:23 -03:00
Hans Verkuil a024c1a6b2 [media] bttv: fix s_tuner for radio
Fix typo: g_tuner should have been s_tuner.

Tested with a bttv card.

Cc: stable@kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-07 15:03:00 -03:00
Hans Verkuil 50e9efd60b [media] pvrusb2: fix g/s_tuner support
The tuner-core subdev requires that the type field of v4l2_tuner is
filled in correctly. This is done in v4l2-ioctl.c, but pvrusb2 doesn't
use that yet, so we have to do it manually based on whether the current
input is radio or not.

Tested with my pvrusb2.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Mike Isely <isely@pobox.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-07 15:02:40 -03:00
Hans Verkuil 227690df75 [media] v4l2-ioctl.c: prefill tuner type for g_frequency and g/s_tuner
The subdevs are supposed to receive a valid tuner type for the g_frequency
and g/s_tuner subdev ops. Some drivers do this, others don't. So prefill
this in v4l2-ioctl.c based on whether the device node from which this is
called is a radio node or not.

The spec does not require applications to fill in the type, and if they
leave it at 0 then the 'check_mode' call in tuner-core.c will return
an error and the ioctl does nothing.

Cc: stable@kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-07 15:02:07 -03:00
Hans Verkuil 9bf0ef060e [media] tuner-core: fix tuner_resume: use t->mode instead of t->type
set_mode is called with t->type, which is the tuner type. Instead, use
t->mode which is the actual tuner mode (i.e. radio vs tv).

Cc: stable@kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-07 15:00:57 -03:00
Hans Verkuil 4e4a31fb95 [media] tuner-core: fix s_std and s_tuner
Both s_std and s_tuner are broken because set_mode_freq is called before the
new std (for s_std) and audmode (for s_tuner) are set.

This patch splits set_mode_freq in a set_mode and a set_freq and in s_std/s_tuner
first calls set_mode, and if that returns 0 (i.e. the mode is supported)
then they set t->std/t->audmode and call set_freq.

This fixes a bug where changing std or audmode would actually change it to
the previous value.

Discovered while testing analog TV standards for cx18 with a tda18271 tuner.

Cc: stable@kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-07 15:00:10 -03:00
Linus Torvalds de3796e77a Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (46 commits)
  [media] rc: call input_sync after scancode reports
  [media] imon: allow either proto on unknown 0xffdc
  [media] imon: auto-config ffdc 7e device
  [media] saa7134: fix raw IR timeout value
  [media] rc: fix ghost keypresses with certain hw
  [media] [staging] lirc_serial: allocate irq at init time
  [media] lirc_zilog: fix spinning rx thread
  [media] keymaps: fix table for pinnacle pctv hd devices
  [media] ite-cir: 8709 needs to use pnp resource 2
  [media] V4L: mx1-camera: fix uninitialized variable
  [media] omap_vout: Added check in reqbuf & mmap for buf_size allocation
  [media] OMAP_VOUT: Change hardcoded device node number to -1
  [media] OMAP_VOUTLIB: Fix wrong resizer calculation
  [media] uvcvideo: Disable the queue when failing to start
  [media] uvcvideo: Remove buffers from the queues when freeing
  [media] uvcvideo: Ignore entities for terminals with no supported format
  [media] v4l: Don't access media entity after is has been destroyed
  [media] media: omap3isp: fix a potential NULL deref
  [media] media: vb2: fix allocation failure check
  [media] media: vb2: reset queued_count value during queue reinitialization
  ...

Fix up trivial conflict in MAINTAINERS as per Mauro
2011-07-06 12:16:49 -07:00
Jarod Wilson 98c32bcded [media] rc: call input_sync after scancode reports
Due to commit cdda911c34, evdev only
becomes readable when the buffer contains an EV_SYN/SYN_REPORT event. If
we get a repeat or a scancode we don't have a mapping for, we never call
input_sync, and thus those events don't get reported in a timely
fashion.

For example, take an mceusb transceiver with a default rc6 keymap. Press
buttons on an rc5 remote while monitoring with ir-keytable, and you'll
see nothing. Now press a button on the rc6 remote matching the keymap.
You'll suddenly get the rc5 key scancodes, the rc6 scancode and the rc6
key spit out all at the same time.

Pressing and holding a button on a remote we do have a keymap for also
works rather unreliably right now, due to repeat events also happening
without a call to input_sync (we bail from ir_do_keydown before getting
to the point where it calls input_sync).

Easy fix though, just add two strategically placed input_sync calls
right after our input_event calls for EV_MSC, and all is well again.
Technically, we probably should have been doing this all along, its just
that it never caused any functional difference until the referenced
change went into the input layer.

input_sync once per IR signal. There was another hidden bug in the code
where we were calling input_report_key using last_keycode instead of our
just discovered keycode, which manifested with the reordering of calling
input_report_key and setting last_keycode.

Reported-by: Stephan Raue <sraue@openelec.tv>
CC: Stephan Raue <sraue@openelec.tv>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Jeff Brown <jeffbrown@android.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-01 16:34:45 -03:00
Jarod Wilson 372b424924 [media] imon: allow either proto on unknown 0xffdc
While 0xffdc devices have their IR protocol hard-coded into the firmware
of the device, we have no known way of telling what it is if we don't
have the device's config byte already in the driver. Unknown devices
default to the imon native protocol, but might actually be rc6, so we
should set the driver up such that the user can load the rc6 keytable
from userspace and still have a working device ahead of its config byte
being added to the driver.

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-01 16:34:01 -03:00
Jarod Wilson 842071c9ea [media] imon: auto-config ffdc 7e device
Another device with the 0xffdc device id, this one with 0x7e in the
config byte. Its an iMON VFD + RC6 IR, in a CoolerMaster 260 case.

Reported-by: Filip Streibl <filip@streibl.cz>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-01 16:33:38 -03:00
Jarod Wilson 9800b5b619 [media] saa7134: fix raw IR timeout value
The comment says "wait 15ms", but the code says jiffies_to_msecs(15)
instead of msecs_to_jiffies(15). Fix that. Tested, works fine with both
rc5 and rc6 decode, in-kernel and via lirc userspace, with an HVR-1150.

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-01 16:33:20 -03:00
Jarod Wilson 3f5c4c7332 [media] rc: fix ghost keypresses with certain hw
With hardware that has to use ir_raw_event_store_edge to collect IR
sample durations, we were not doing an event reset unless
IR_MAX_DURATION had passed. That's around 4 seconds. So if someone
presses up, then down, with less than 4 seconds in between, they'd get
the initial up, then up and down upon pressing down.

To fix this, I've lowered the "send a reset event" logic's threshold to
the input device's REP_DELAY (defaults to 500ms), and with an
saa7134-based GPIO-driven IR receiver in a Hauppauge HVR-1150, I get
*much* better behavior out of the remote now. Special thanks to Devin
for providing the hardware to investigate this issue.

CC: stable@kernel.org
CC: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-01 16:33:01 -03:00
Jarod Wilson 1ba9268c2b [media] keymaps: fix table for pinnacle pctv hd devices
Both consumers of RC_MAP_PINNACLE_PCTV_HD send along full RC-5
scancodes, so this update makes this keymap actually *have* full
scancodes, heisted from rc-dib0700-rc5.c. This should fix out of the box
remote functionality for the Pinnacle PCTV HD 800i (cx88 pci card) and
PCTV HD Pro 801e (em28xx usb stick).

CC: stable@kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-01 16:31:54 -03:00
Jarod Wilson 35d136c8da [media] ite-cir: 8709 needs to use pnp resource 2
Thanks to the intrepid testing and debugging of Matthijs van Drunen, it
was uncovered that at least some variants of the ITE8709 need to use pnp
resource 2, rather than 0, for things to function properly. Resource 0
has a length of only 1, and if you try to bypass the pnp_port_len check
and use it anyway (with either a length of 1 or 2), the system in
question's trackpad ceased to function.

The circa lirc 0.8.7 lirc_ite8709 driver used resource 2, but the value
was (amusingly) changed to 0 by way of a patch from ITE themselves, so I
don't know if there may be variants where 0 actually *is* correct, but
at least in this case and in the original lirc_ite8709 driver author's
case, it sure looks like 2 is the right value.

This fix should probably be applied to all stable kernels with the
ite-cir driver, lest we nuke more people's trackpads.

Tested-by: Matthijs van Drunen
CC: Juan Jesús García de Soria <skandalfo@gmail.com>
CC: stable@kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-01 16:31:38 -03:00
Andre Bartke 258c05637d [media] V4L: mx1-camera: fix uninitialized variable
mx1_camera_add_device() can return an uninitialized value of ret.

Signed-off-by: Andre Bartke <andre.bartke@gmail.com>
[g.liakhovetski@gmx.de: modified the fix to remove "ret" completely]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-01 15:51:34 -03:00
Vaibhav Hiremath 383e4f6987 [media] omap_vout: Added check in reqbuf & mmap for buf_size allocation
The usecase where, user allocates small size of buffer
through bootargs (video1_bufsize/video2_bufsize) and later from application
tries to set the format which requires larger buffer size, driver doesn't
check for insufficient buffer size and allows application to map extra buffer.
This leads to kernel crash, when user application tries to access memory
beyond the allocation size.

Added check in both mmap and reqbuf call back function,
and return error if the size of the buffer allocated by user through
bootargs is less than the S_FMT size.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-01 15:47:53 -03:00
Vaibhav Hiremath 8f3a307b9a [media] OMAP_VOUT: Change hardcoded device node number to -1
With addition of media-controller framework, now we have various
device nodes (/dev/videoX) getting created, so hardcoding
minor number in video_register_device() is not recommended.

So let V4L2 framework choose free minor number for the device.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-01 15:46:46 -03:00
Vladimir Pantelic e8bb10b82f [media] OMAP_VOUTLIB: Fix wrong resizer calculation
The omap_vout_new_crop() function has possible bug, uses uninitialized
variable "crop.width/height" which is actually output of the function.
Instead we should be using "try_crop.width/height" to calculate the
resizer value.

Signed-off-by: Vladimir Pantelic <vladoman@gmail.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-01 15:46:24 -03:00
Sjoerd Simons aa122d424b [media] uvcvideo: Disable the queue when failing to start
When failing to start the camera we should disable the queue again, to
rollback into the same initial state. Otherwise re-trying will always
hit -EBUSY

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-30 23:19:16 -03:00
Sjoerd Simons 8ca2c80b17 [media] uvcvideo: Remove buffers from the queues when freeing
When freeing memory for the video buffers also remove them from the
irq & main queues.

This fixes an oops when doing the following:

open ("/dev/video", ..)
VIDIOC_REQBUFS
VIDIOC_QBUF
VIDIOC_REQBUFS
close ()

As the second VIDIOC_REQBUFS will cause the list entries of the buffers
to be cleared while they still hang around on the main and irc queues

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-30 23:18:52 -03:00
Laurent Pinchart a96aa5342d [media] uvcvideo: Ignore entities for terminals with no supported format
If a streaming interface has no supported format, the driver won't
create a video device for the associated terminal. Fix an oops by
ignoring that terminal when creating links between entities.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-30 23:18:13 -03:00
Laurent Pinchart c064b8eac8 [media] v4l: Don't access media entity after is has been destroyed
Entities associated with video device nodes are unregistered in
video_unregister_device(). This destroys the entity even though it can
still be accessed through open video device nodes.

Move the media_device_unregister_entity() call from
video_unregister_device() to v4l2_device_release() to ensure that the
entity isn't unregistered until the last reference to the video device
is released.

Also remove the media_entity_get()/put() calls from v4l2-dev.c. Those
functions were designed for subdevs, to avoid a parent module from being
removed while still accessible through board code. They're not currently
needed for video device nodes, and will oops when a hotpluggable device
is disconnected during streaming, as media_entity_put() called in
v4l2_device_release() tries to access entity->parent->dev->driver which
is set to NULL when the device is disconnected.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-30 23:12:36 -03:00
Ohad Ben-Cohen ca4186f06f [media] media: omap3isp: fix a potential NULL deref
Fix a potential NULL pointer dereference by skipping registration of
external entities in case none are provided.

This is useful at least when testing mere memory-to-memory scenarios.

Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-30 23:01:05 -03:00
Marek Szyprowski 66072d4fa7 [media] media: vb2: fix allocation failure check
__vb2_queue_alloc function returns the number of successfully allocated
buffers. There is no point in checking if the returned value is negative.
If this function returns 0, videobuf2 should just return -ENOMEM to
userspace, because no driver can work without memory buffers.

Reported-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-30 22:33:47 -03:00
Marek Szyprowski afdea8bac5 [media] media: vb2: reset queued_count value during queue reinitialization
queued_count variable was left untouched during the queue reinitialization
in __vb2_queue_cancel, what might lead to mismatch between the real number
of queued buffers and queued_count variable.

Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-30 22:32:58 -03:00
Marek Szyprowski bf7b73efb7 [media] Revert "[media] v4l2: vb2: one more fix for REQBUFS()"
This reverts commit 31901a078a.

Queue should be reinitialized on each REQBUFS() call even if the memory
access method and buffer count have not been changed. The user might have
changed the format and if we go the short path introduced in that commit,
the memory buffer will not be reallocated to fit with new format.

The previous patch was just over-engineered optimization, which just
introduced a bug to videobuf2.

Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-30 22:32:28 -03:00
Marek Szyprowski a52a82fc3a [media] media: vb2: add __GFP_NOWARN to dma-sg allocator
Add __GFP_NOWARN parameter to videobuf2 dma-sg allocator to prevent
kernel warning and stack dump if there is not enough memory available.
Videobuf2 and drivers should correctly handle no memory case, so there
is no need for stack dump and extensive log.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-30 22:31:53 -03:00
Alexey Dobriyan b7f080cfe2 net: remove mm.h inclusion from netdevice.h
Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).

To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.

Hope people are OK with tiny include file.

Note, that mm_types.h is still dragged in, but it is a separate story.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-21 19:17:20 -07:00
Hans de Goede 9a7b2d1f0e [media] pwc: better usb disconnect handling
Unplugging a pwc cam while an app has the /dev/video# node open leads
to an oops in pwc_video_close when the app closes the node, because
the disconnect handler has free-ed the pdev struct pwc_video_close
tries to use. Instead of adding some sort of bandaid for this.
fix it properly using the v4l2 core's new(ish) behavior of keeping the
v4l2_dev structure around until both unregister has been called, and
all file handles referring  to it have been closed:

Embed the v4l2_dev structure in the pdev structure and define a v4l2 dev
release callback releasing the pdev structure (and thus also the embedded
v4l2 dev structure.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-21 13:31:12 -03:00
David S. Miller 9f6ec8d697 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/wireless/iwlwifi/iwl-agn-rxon.c
	drivers/net/wireless/rtlwifi/pci.c
	net/netfilter/ipvs/ip_vs_core.c
2011-06-20 22:29:08 -07:00
Vitaliy Ivanov e44ba033c5 treewide: remove duplicate includes
Many stupid corrections of duplicated includes based on the output of
scripts/checkincludes.pl.

Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-06-20 16:08:19 +02:00
HeungJun, Kim c30701130c [media] m5mols: Use proper email address format
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:46:00 -03:00
HeungJun, Kim a6354d2e5d [media] m5mols: remove union in the m5mols_get_version(), and VERSION_SIZE
Remove union version in the m5mols_get_version(), and read version information
directly. Also remove VERSION_SIZE.

Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:45:55 -03:00
HeungJun, Kim 57644f5623 [media] m5mols: add m5mols_read_u8/u16/u32() according to I2C byte width
For now, the m5mols_read() share in case of I2C packet 1, 2, 4 byte(s) width.
So, this commit adds 3 functions - m5mols_read_u8/u16/u32() according to byte
width of I2C packet. And, the u32 variables in spite of u8 or u16 for fitting
to m5mols_read() having no choice, is replaced to have original byte width
like u8, u16, u32 as same reason.

Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:45:51 -03:00
HeungJun, Kim bbe66edc60 [media] m5mols: Fix capture image size register definition
The main capture and the thumbnail image size registers were
erroneously defined to have 1 byte width, resulting in wrong
reported image size. Fix this by changing the registers width
to correct value.

Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:45:47 -03:00
Sylwester Nawrocki 3a3f94497a [media] s5p-fimc: Update copyright notices
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:45:43 -03:00
Sylwester Nawrocki ba0545e328 [media] s5p-fimc: Use pix_mp for the color format lookup
With multi-planar formats fmt.pix_mp member of struct v4l2_format
should be used rather than fmt.pix. Fix find_fmt() function to do
the right thing.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:45:39 -03:00
Sylwester Nawrocki dbdd0dfb89 [media] s5p-fimc: Remove empty buf_init operation
The buf_init buffer queue operation is optional and
buffer_init() does nothing, remove it.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:45:35 -03:00
Sylwester Nawrocki a629f86b4a [media] s5p-fimc: Fix wrong buffer size in queue_setup
Avoid dereferencing of NULL f->fmt. Correct size of the allocated
buffer in case the crop rectangle is smaller than the bounds
rectangle (configured with S_FMT). Also remove redundant check
for *num_buffer == 0 as this case is handled in videobuf2.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:45:32 -03:00
Sylwester Nawrocki 3495dcefeb [media] s5p-fimc: Fix data structures documentation and cleanup debug trace
Correct inconsistencies in data structures' documentation.
Remove meaningless debug traces.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:45:28 -03:00
Sylwester Nawrocki 6ba8d13b0c [media] s5p-fimc: Fix V4L2_PIX_FMT_RGB565X description
Remove V4L2_MBUS_FMT_RGB565_2X8_BE media code entry as
camera interface supports only packed YUYV formats.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:45:24 -03:00
Sylwester Nawrocki cfd77310a9 [media] s5p-fimc: Fix possible memory leak during capture devnode registration
Add missing kfree on the error path.

Reported-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:45:20 -03:00
Jarod Wilson 94215ccd99 [media] imon: fix initial panel key repeat suppression
As pointed out on the lirc list by Andreas Dick, initial panel key
repeat suppression wasn't working, as we had no timevals accumulated
until after the first repeat. Also add a missing locking call.

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:04:24 -03:00
Jarod Wilson 443b391900 [media] imon: support for 0x46 0xffdc imon vfd
Courtesy of information from Andreas Dick on the lirc list.

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:04:16 -03:00
Jarod Wilson 0b43fcdff6 [media] mceusb: plug memory leak on data transmit
Hans Petter Selasky pointed out to me that we're leaking urbs when
mce_async_out is called. Its used both for configuring the hardware and
for transmitting IR data. In the tx case, mce_request_packet actually
allocates both a urb and the transfer buffer, neither of which was being
torn down. Do that in the tx callback.

CC: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:04:04 -03:00
Jarod Wilson 589e116062 [media] nuvoton-cir: in_use isn't actually in use, remove it
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:03:46 -03:00
Jarod Wilson 0ae90252d0 [media] fintek-cir: make suspend with active IR more reliable
There was a missing lock in fintek_suspend. Without the lock, its
possible the system will be in the middle of receiving IR (draining the
RX buffer) when we try to disable CIR interrupts.

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:03:35 -03:00
Jarod Wilson 8de111e276 [media] lirc_dev: store cdev in irctl, up maxdevs
Store the cdev pointer in struct irctl, allocated dynamically as needed,
rather than having a static array. At the same time, recycle some of the
saved memory to nudge the maximum number of lirc devices supported up a
ways -- its not that uncommon these days, now that we have the rc-core
lirc bridge driver, to see a system with at least 4 raw IR receivers.
(consider a mythtv backend with several video capture devices and the
possible need for IR transmit hardware).

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:03:20 -03:00
Jarod Wilson 3a918aa69d [media] mceusb: mce_sync_in is brain-dead
Aside from the initial "hey, lets make sure we've flushed any
pre-existing data on the device" call to mce_sync_in, every other one of
the calls was entirely superfluous. Ergo, remove them all, and rename
the one and only (questionably) useful one to reflect what it really
does. Verified on both gen2 and gen3 hardware to make zero difference.
Well, except that you no longer get a bunch of urb submit failures from
the unneeded mce_sync_in calls. Oh. And move that flush to a point
*after* we've wired up the inbound urb, or it won't do squat. I have
half a mind to just remove it entirely, but someone thought it was
necessary at some point, and it doesn't seem to hurt, so lets leave it
for the time being.

This excercise took place due to insightful questions asked by Hans
Petter Selasky, about the possible reuse of the inbound urb before it
was actually availble by mce_sync_in, so thanks to him for motivating
this cleanup.

Reported-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:02:07 -03:00
Jarod Wilson b825fe1b1b [media] mceusb: support I-O Data GV-MC7/RCKIT
There's an SMK-device-id remote kit from I-O Data avaiable primarily in
Japan, which appears to have no tx hardware, but has rx functionality
that works with the mceusb driver by simply adding its device ID.

Reported-by: Jeremy Kwok <jeremykwok@desu.ca>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:01:40 -03:00
Jarod Wilson 5ae8f9a375 [media] mceusb: add and use mce_dbg printk macro
Using dev_dbg is more complexity than many users are able to deal with.
Make it easier to get debug spew feedback from them by adding an mce_dbg
printk macro that spews using dev_info when debug=1 is set for the
mceusb module.

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-11 09:01:22 -03:00
Joe Perches 28f65c11f2 treewide: Convert uses of struct resource to resource_size(ptr)
Several fixes as well where the +1 was missing.

Done via coccinelle scripts like:

@@
struct resource *ptr;
@@

- ptr->end - ptr->start + 1
+ resource_size(ptr)

and some grep and typing.

Mostly uncompiled, no cross-compilers.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-06-10 14:55:36 +02:00
Linus Torvalds 461df4ded3 Merge branch 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  staging: iio: max517: Fix iio_info changes
  Staging: mei: fix debug code
  Staging: cx23885: fix include of altera.h
  staging: iio: error case memory leak fix
  staging: ath6kl: Fix a kernel panic during suspend/resume
  staging: gma500: get control from firmware framebuffer if conflicts
  staging: gma500: Skip bogus LVDS VBT mode and check for LVDS before adding backlight
  staging: usbip: bugfix prevent driver unbind
  staging: iio: industrialio-trigger: set iio_poll_func private_data
  staging: rts_pstor: use bitwise operator instead of logical one
  staging: fix ath6kl build when CFG80211 is not enabled
  staging: brcm80211: fix for 'multiple definition of wl_msg_level' build err
  staging: fix olpc_dcon build, needs BACKLIGHT_CLASS_DEVICE
  Staging: remove STAGING_EXCLUDE_BUILD option
  Staging: altera: move .h file to proper place
2011-06-09 13:09:07 -07:00
Greg Kroah-Hartman e2d4dc5af3 Staging: cx23885: fix include of altera.h
The cx23885 driver was including staging/altera.h, but that file has
moved back into the driver directory.

Why a non-staging driver was including a staging driver is beyond me,
but this fixes the build so everything is happy for now.

For the record, it's not ok for a non-staging driver to depend on a
staging one, as that implies that the non-staging one should also be in
the staging tree if that's needed.

Cc: Igor M. Liplianin <liplianin@netup.ru>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-06-08 09:18:32 -07:00
Alexey Dobriyan a6b7a40786 net: remove interrupt.h inclusion from netdevice.h
* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-06 22:55:11 -07:00
Mauro Carvalho Chehab d364ee4fdb [media] soc_camera: preserve const attribute
drivers/media/video/soc_camera.c: In function ‘soc_camera_video_start’:
drivers/media/video/soc_camera.c:1515: warning: initialization discards qualifiers from pointer target type

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-01 15:03:56 -03:00
Mauro Carvalho Chehab 76df01eacd [media] uvc_entity: initialize return value
drivers/media/video/uvc/uvc_entity.c: In function ‘uvc_mc_register_entities’:
drivers/media/video/uvc/uvc_entity.c:33: warning: ‘ret’ may be used uninitialized in this function

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-01 14:45:52 -03:00
Laurent Pinchart 8c89ddd536 [media] media: Fix media device minor registration
The find_next_zero_bit() is called with the from and to arguments in the
wrong order. This results in the function always returning 0, and all
media devices being registered with minor 0. Furthermore, mdev->minor is
then used before being assigned with the find_next_zero_bit() return
value. This really makes sure we'll always use minor 0.

Fix this and let the system support more than one media device.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-01 13:24:23 -03:00
Hans Petter Selasky 67e27c7413 [media] Make nchg variable signed because the code compares this variable against negative values
The sonixj driver compares the value for nchg with:
 		if (sd->nchg < -6 || sd->nchg >= 12) {

With u8, negative values won't work.

Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-01 12:20:57 -03:00
Sanjeev Premi 6c20c635b8 [media] omap3isp: fix compiler warning
This patch fixes this compiler warning:
  drivers/media/video/omap3isp/isp.c: In function 'isp_isr_dbg':
  drivers/media/video/omap3isp/isp.c:392:2: warning: zero-length
   gnu_printf format string

Signed-off-by: Sanjeev Premi <premi@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-01 09:42:28 -03:00
Ian Armstrong c5874c9245 [media] ivtv: Internally separate encoder & decoder standard setting
Internally separates the setting of the broadcast standard for the encoder &
decoder. Externally there's no change in functionality.

[awalls@md.metrocast.net: Edited to fix a checkpatch gripe about multiple
assignment and to remove a now unused DEFINE_WAIT() due to this patch]

Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-01 08:46:38 -03:00
Ian Armstrong 6600cc301d [media] ivtvfb: Add sanity check to ivtvfb_pan_display()
Add sanity check to ivtvfb_pan_display() to ensure only valid values are used
to pan the display. Invalid values are rejected with -EINVAL

Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-01 08:45:36 -03:00
Laurent Pinchart 5d9c08dea0 [media] ivtvfb: use display information in info not in var for panning
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it. Also use the
aligned fix.line_length and not the (possible) unaligned xres_virtual.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-01 08:45:19 -03:00
Ian Armstrong 7700a0d293 [media] ivtv: Make two ivtv_msleep_timeout calls uninterruptable
Two ivtv_msleep_timeout() calls are incorrectly flagged as interruptable. The
first is in the init sequence for a capture and is required for stable
hardware setup. The second is at the end of the capture and used to handle the
last data transfer. Failure to wait for this last transfer can result in stale
data being read at the start of the next capture.

Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-01 08:45:03 -03:00
Antti Palosaari 21d2e938d3 [media] anysee: return EOPNOTSUPP for unsupported I2C messages
Check I2C messages and return error properly.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-01 08:34:45 -03:00
Jean-François Moine c8ef0a5b70 [media] gspca - ov519: Set the default frame rate to 15 fps
The frame rate variable was not initialized, so, the lowest frame rate was
used for most webcams.

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-01 08:27:43 -03:00
Jean-François Moine 5ff01d54fe [media] gspca - stv06xx: Set a lower default value of gain for hdcs sensors
Many users said that the default gain value (128) was giving white images.
The value which was in the original qc-usb driver (50) is better.

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-01 08:26:54 -03:00
Jean-François Moine 0e44173b12 [media] gspca: Remove coarse_expo_autogain.h
This file is replaced by autogain_functions.h.

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-01 08:26:30 -03:00
Jean-François Moine 9cf208e844 [media] gspca - ov519: Change the ovfx2 bulk transfer size
The 'normal' bulk transfer size did not work for 800x600.
By git commit c42cedbb65, this 'normal' size was used for 1600x1200 only.
It will now be used back again for all resolutions but 800x600.

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-01 08:26:11 -03:00
Jean-François Moine 9d2b909544 [media] gspca - ov519: Fix a regression for ovfx2 webcams
By git commit c42cedbb65, the bulk transfer size was changed to a lower
value for resolutions != 1600x1200, but the image extraction routine still
worked with the previous value, giving bad truncated images.

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-06-01 08:25:56 -03:00
Linus Torvalds c0880dcded Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  [media] v1.88 DM04/QQBOX Move remote to use rc_core dvb-usb-remote
  [media] Add missing include guard to header file
  [media] Inlined functions should be static
  [media] Remove invalid parameter description
  [media] cpia2: fix warning about invalid trigraph sequence
  [media] s5p-csis: Add missing dependency on PLAT_S5P
  [media] gspca/kinect: wrap gspca_debug with GSPCA_DEBUG
  [media] fintek-cir: new driver for Fintek LPC SuperIO CIR function
  [media] uvcvideo: Connect video devices to media entities
  [media] uvcvideo: Register subdevices for each entity
  [media] uvcvideo: Register a v4l2_device
  [media] add V4L2-PIX-FMT-SRGGB12 & friends to docbook
  [media] Documentation/DocBook: Rename media fops xml files
  [media] Media DocBook: fix validation errors
  [media] wl12xx: g_volatile_ctrl fix: wrong field set
  [media] fix kconfig dependency warning for VIDEO_TIMBERDALE
  [media] dm1105: GPIO handling added, I2C on GPIO added, LNB control through GPIO reworked
  [media] Add support for M-5MOLS 8 Mega Pixel camera ISP
2011-05-27 10:14:22 -07:00
Linus Torvalds b7c2f03628 Merge branch 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
  gfs2: Drop __TIME__ usage
  isdn/diva: Drop __TIME__ usage
  atm: Drop __TIME__ usage
  dlm: Drop __TIME__ usage
  wan/pc300: Drop __TIME__ usage
  parport: Drop __TIME__ usage
  hdlcdrv: Drop __TIME__ usage
  baycom: Drop __TIME__ usage
  pmcraid: Drop __DATE__ usage
  edac: Drop __DATE__ usage
  rio: Drop __DATE__ usage
  scsi/wd33c93: Drop __TIME__ usage
  scsi/in2000: Drop __TIME__ usage
  aacraid: Drop __TIME__ usage
  media/cx231xx: Drop __TIME__ usage
  media/radio-maxiradio: Drop __TIME__ usage
  nozomi: Drop __TIME__ usage
  cyclades: Drop __TIME__ usage
2011-05-26 13:19:00 -07:00
Samuel Ortiz 3271d382c3 mfd: Use mfd cell platform_data for timberdale cells platform bits
With the addition of a device platform mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.

Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-05-26 19:45:05 +02:00
Samuel Ortiz 9e554696c0 mfd: Use mfd cell platform_data for wl1273 cells platform bits
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.

Cc: Matti Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-05-26 19:45:02 +02:00
Malcolm Priestley 616a4b83bd [media] v1.88 DM04/QQBOX Move remote to use rc_core dvb-usb-remote
driver to use dvb-usb-remote.
The remote(s) generates 24 bit NEC codes, lme2510 keymaps redefined.

Other minor fixes
fix le warning.
make sure frontend is detached on firmware change.

Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 21:50:17 -03:00
Hans Petter Selasky 96c68795dc [media] Inlined functions should be static
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 21:42:26 -03:00
Hans Petter Selasky 2edcdfae98 [media] Remove invalid parameter description
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 21:42:23 -03:00
Hans Petter Selasky ed82b9c26e [media] cpia2: fix warning about invalid trigraph sequence
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 21:42:19 -03:00
Sylwester Nawrocki 05fb85e1b2 [media] s5p-csis: Add missing dependency on PLAT_S5P
s5p-csis is to be built only on S5P SoC platforms.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 20:08:08 -03:00
Jarod Wilson ce14dcdba6 [media] gspca/kinect: wrap gspca_debug with GSPCA_DEBUG
Fixes media_build, and presumably certain other upstream kernel build
option combos.

Before:
  CC [M]  /home/jarod/src/media_build/v4l/kinect.o
/home/jarod/src/media_build/v4l/kinect.c:38:19: error: 'D_ERR' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:38:27: error: 'D_PROBE' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:38:37: error: 'D_CONF' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:38:46: error: 'D_STREAM' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:38:57: error: 'D_FRAM' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:38:66: error: 'D_PACK' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:39:2: error: 'D_USBI' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:39:11: error: 'D_USBO' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:39:20: error: 'D_V4L2' undeclared here (not in a function)
make[3]: *** [/home/jarod/src/media_build/v4l/kinect.o] Error 1

After:
  CC [M]  /home/jarod/src/media_build/v4l/kinect.o
  ...
  LD [M]  /home/jarod/src/media_build/v4l/gspca_kinect.ko
  ...
  profit

Reported-by: Nicolas Will <nico@youplala.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 20:08:01 -03:00
Jarod Wilson 9bdc79ea07 [media] fintek-cir: new driver for Fintek LPC SuperIO CIR function
This is a new driver for the Fintek LPC SuperIO CIR function, in the
Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so
thanks go to them for supporting this effort.

This driver started out as a copy of the nuvoton-cir driver, and was
then modified as needed for the Fintek chip. The two share many
similaries, though the buffer handling for the Fintek chip is actually
nearly identical to the mceusb buffer handling, so the parser routine is
almost a drop-in copy of the mceusb buffer parser (a candidate for being
abstracted out into shared code at some point).

This initial code drop *only* supports receive, but the hardware does
support transmit as well. I really haven't even started to look at
what's required, but my guess is that its also pretty similar to mceusb.
Most people are probably only really interested in RX anyway though, so
I think its good to get this out there even with only RX.

(Nb: there are also Fintek-made mceusb receivers, which presumably, this
chip shares CIR hardware with).

This hardware can be found on at least Jetway NC98 boards and derivative
systems, and likely others as well. Functionality was tested with an
NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge)
and NEC-ish (tivo) remotes all successful, as was lirc userspace decode
of the RC6 remote.

CC: Aaron Huang <aaron_huang@fintek.com.tw>
CC: Tom Tsai <tom_tsai@fintek.com.tw>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 20:07:58 -03:00
Laurent Pinchart 8a65a94858 [media] uvcvideo: Connect video devices to media entities
The video devices associated to USB streaming terminals must be
connected to their associated terminal's media entity instead of being
standalone entities.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 19:51:09 -03:00
Laurent Pinchart 4ffc2d89f3 [media] uvcvideo: Register subdevices for each entity
Userspace applications can now discover the UVC device topology using
the media controller API.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 19:50:58 -03:00
Laurent Pinchart 5a254d751e [media] uvcvideo: Register a v4l2_device
As a first step to the media controller integration register a
v4l2_device for each UVC control interface and make the video_device a
child of the v4l2_device.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 19:50:49 -03:00