The newly added hwmon driver fails to build in an allmodconfig
kernel:
ERROR: "memblock_is_memory" [drivers/hwmon/xgene-hwmon.ko] undefined!
According to comments in the code, the mailbox is a shared memory region,
not a set of MMIO registers, so we should use memremap() for mapping it
instead of ioremap or acpi_os_ioremap, and pointer dereferences instead
of readl/writel.
The driver already uses plain kernel pointers, so it's a bit unusual
to work with functions that operate on __iomem pointers, and this
fixes that part too.
I'm using READ_ONCE/WRITE_ONCE here to keep the existing behavior
regarding the ordering of the accesses from the CPU, but note that
there are no barriers (also unchanged from before).
I'm also keeping the endianness behavior, though I'm unsure whether
the message data was supposed to be in LE32 format in the first
place, it's possible this was meant to be interpreted as a byte
stream instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hoan Tran <hotran@apm.com>
Tested-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Simplify code and reduce code size by using the new hwmon
registration API.
Other changes:
- Convert to use regmap, and drop local caching. This avoids reading
registers unnecessarily, and uses regmap for caching of non-volatile
registers.
- Add support for temp2_max, temp2_max_alarm, temp2_max_hyst, and
temp2_offset.
- Order include files alphabetically
- Drop FSF address
- Check errors from register read and write functions and report
to userspace.
- Accept negative hysteresis values. While unlikely, a maximum limit
_can_ be set to a value smaller than 31 degrees C, which makes negative
hysteresis values possible.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The system crashes during probing xgene-hwmon driver when temperature
alarm interrupt occurs before.
It's because
- xgene_hwmon_probe() requests mailbox channel which also enables
the mailbox interrupt.
- As temperature alarm interrupt is pending, ISR runs and crashes when
accesses into invalid resourse as unmapped PCC shared memory.
This patch fixes this issue by saving this alarm message and scheduling a
bottom handler after xgene_hwmon_probe() finish.
Signed-off-by: Hoan Tran <hotran@apm.com>
Reported-by: Itaru Kitayama <itaru.kitayama@riken.jp>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
iio_channel_get_all returns -ENODEV when it cannot find either phandles and
properties in the Device Tree or channels whose consumer_dev_name matches
iio_hwmon in iio_map_list. The iio_map_list is filled in by iio drivers
which might be probed after iio_hwmon.
It is better to defer the probe of iio_hwmon if such error is returned by
iio_channel_get_all in order to let a chance to iio drivers to expose
channels in iio_map_list.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The fan can be stopped by writing "3" to pwm1_enable in sysfs.
Add devicetree property for early initialization of the fan controller
to prevent overheating, for example when resetting the board while the
fan was completely turned off.
Also improve error reporting, I2C failures were ignored while writing
new values.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Parse devicetree parameters for voltage and prescaler setting. This allows
using multiple max6550 devices with varying settings, and also makes it
possible to instantiate and configure the device using devicetree.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Remove the index comments at the end of it87_attributes_in. They
serve no purpose (as there is no reference to them in
it87_in_is_visible) and some of them were obviously wrong.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The UCD90160 Power Supply Sequencer reuses the existing register layout,
so just an id addition was required.
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Ronak Desai <ronak.desai@rockwellcollins.com>
[groeck: Updated description, ordered alphabetically, added documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The field "owner" is set by the core.
Thus delete an unneeded initialisation.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds hardware temperature and power reading support for
APM X-Gene SoC using the mailbox communication interface.
Signed-off-by: Hoan Tran <hotran@apm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If both hwmon and thermal_sys are built as modules, and
CONFIG_THERMAL_HWMON is enabled, the following cyclic module dependency
is reported.
depmod: ERROR: Found 2 modules in dependency cycles!
depmod: ERROR: Cycle detected: hwmon -> thermal_sys -> hwmon
Fixes: e4bce763adb2 ("hwmon: (core) New hwmon registration API")
Reported-by: Vignesh R <vigneshr@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADT7470 supports a variety of PWM frequencies. This patch allows the
frequency to be configured and viewed through the sysfs entry pwm1_freq.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Allow to specify the resistance of the attached shunt via DT by
adding the shunt-resistor property. Fall-back to the previous
default (1 mOhm) if unset.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[groeck: Fixed 'line over 80 columns' checkpatch warning]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since commit 698a7c24a5 ("hwmon: (nct6775) Support two SuperIO chips
in the same system"), the driver supports two Super-IO chips. This has
the undesirable side effect that force_id always detects a second chip
at address 0xfff8, even if no chip exists at that address.
nct6775: Found NCT6793D or compatible chip at 0x4e:0xfff8
If no chip at all is found at a given SIO address, it does not make sense
to instantiate it. Limit force_id to only work if some chip is found,
that is if the chip ID returns a value other than 0xffff.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add basic pwm attribute support (no auto attributes) to new API.
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Up to now, each hwmon driver has to implement its own sysfs attributes.
This requires a lot of template code, and distracts from the driver's core
function to read and write chip registers.
To be able to reduce driver complexity, move sensor attribute handling
and thermal zone registration into hwmon core. By using the new API,
driver code and data size is typically reduced by 20-70%, depending
on driver complexity and the number of sysfs attributes supported.
With this patch, the new API only supports thermal sensors. Support for
other sensor types will be added with subsequent patches.
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Ordering include files alphabetically makes it easier to add new ones.
Stop including linux/spinlock.h and linux/kdev_t.h since both are not
needed.
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of repeatedly accessing &pdev->dev, use a local variable dev
instead where possible. Also drop 'dev' from private data since it is
unnecessary.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Provide support for PSU DPS-460, DPS-800 from Delta Electronics, INC
and for SGD009 from Acbel Polytech, INC.
These devices do not support the STATUS_CML register, and reports a
communication error in response to this command. For this reason,
the status register check is disabled for these controllers.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If the EXT_TDM bit is set, the chip supports a second temperature sensor
instead of two voltage sensors.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The lower temperature limit is -128 degrees C. The supported upper limits
are 127.875 or 255.875 degrees C. Also, don't fail if a value outside
the supported range is provided when setting a temperature limit.
Instead, clamp the provided value to the available value range.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writing the update_interval attribute could result in an overflow if
a number close to the maximum unsigned long was written. At the same
time, even though the chip supports setting the conversion rate,
the selected conversion rate was not actually written to the chip.
Fix the second problem by selecting valid (supported) conversion rates,
and writing the selected conversion rate to the chip. This also fixes the
first problem, since arbitrary conversion rates are now converted to
actually supported conversion rates.
Also, set the default chip conversion rate to 1 second. Previously, the
chip was configured for continuous conversion, but readings were only
retrieved every seond, which doesn't make much sense. If we only read a
value from the chip every second, we can as well save some power and only
convert in one-second intervals.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Attribute array it87_attributes_in lacks its NULL terminator,
causing random behavior when operating on the attribute group.
Fixes: 5292971563 ("hwmon: (it87) Use is_visible for voltage sensors")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Coverity reports:
result_independent_of_operands: data->features & (65536UL /* 1UL << 16 */)
is always 0 regardless of the values of its operands. This occurs as the
logical operand of if.
data->features needs to be 32 bit wide since there are more than 16 features.
Fixes: cc18da79d9 ("hwmon: (it87) Support up to 6 temperature sensors ... ");
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
According to the datasheet we have to set some bits as 0 and others as 1.
Make sure we do this for CFG1 and CFG3.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The "name" variable's memory is now freed when the device is destructed
thanks to devm function.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: e0f8a24e0e ("staging:iio::hwmon interface client driver.")
Fixes: 61bb53bcbd ("hwmon: (iio_hwmon) Add support for humidity sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using set_bit() to set a bit in an integer is not a good idea, since
the function expects an unsigned long as argument, which can be 64 bit
wide. Coverity reports this problem as
>>> CID 1364488: Memory - illegal accesses (INCOMPATIBLE_CAST)
>>> Pointer "&ret" points to an object whose effective type is "int"
>>> (32 bits, signed) but is dereferenced as a wider "unsigned
+long" (64 bits, unsigned). This may lead to memory corruption.
245 set_bit(1, (unsigned long *)&ret);
Just use BIT instead.
Cc: Thilo Cestonaro <thilo@cestona.ro>
Fixes: 08426eda58 ("hwmon: Add driver for FTS BMC chip "Teutates"")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Replace devm_add_action() with devm_add_action_or_reset(),
and check its return value.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Handling the wraparound requires the data->last_update to be set to an
initial jiffies value. Otherwise on 32-bit systems you will not be able
to request a reading till the 5 minute jiffies rollover happens.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: David Frey <david.frey@sensirion.com>
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Fixes: 7c84f7f80d ("hwmon: add support for Sensirion SHT3x sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull i2c updates from Wolfram Sang:
"Here is the I2C pull request for 4.8:
- the core and i801 driver gained support for SMBus Host Notify
- core support for more than one address in DT
- i2c_add_adapter() has now better error messages. We can remove all
error messages from drivers calling it as a next step.
- bigger updates to rk3x driver to support rk3399 SoC
- the at24 eeprom driver got refactored and can now read special
variants with unique serials or fixed MAC addresses.
The rest is regular driver updates and bugfixes"
* 'i2c/for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (66 commits)
i2c: i801: use IS_ENABLED() instead of checking for built-in or module
Documentation: i2c: slave: give proper example for pm usage
Documentation: i2c: slave: describe buffer problems a bit better
i2c: bcm2835: Don't complain on -EPROBE_DEFER from getting our clock
i2c: i2c-smbus: drop useless stubs
i2c: efm32: fix a failure path in efm32_i2c_probe()
Revert "i2c: core: Cleanup I2C ACPI namespace"
Revert "i2c: core: Add function for finding the bus speed from ACPI"
i2c: Update the description of I2C_SMBUS
i2c: i2c-smbus: fix i2c_handle_smbus_host_notify documentation
eeprom: at24: tweak the loop_until_timeout() macro
eeprom: at24: add support for at24mac series
eeprom: at24: support reading the serial number for 24csxx
eeprom: at24: platform_data: use BIT() macro
eeprom: at24: split at24_eeprom_write() into specialized functions
eeprom: at24: split at24_eeprom_read() into specialized functions
eeprom: at24: hide the read/write loop behind a macro
eeprom: at24: call read/write functions via function pointers
eeprom: at24: coding style fixes
eeprom: at24: move at24_read() below at24_eeprom_write()
...
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
According to the datasheet you should only write 1 to this bit. If it is
not set, at least AIN3 will return bad values on newer silicon revisions.
Fixes: d84ca5b345 ("hwmon: Add driver for ADT7411 voltage and temperature sensor")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver implements hardware monitoring and watchdog support
for the FTS BMC Chip "Teutates".
Signed-off-by: Thilo Cestonaro <thilo@cestona.ro>
[groeck: Updated subject and description; fixed dependencies]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The enables control of the SHT31 sensors heating element that can turned
on to remove excess humidity.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: David Frey <david.frey@sensirion.com>
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
With this change, JC-42.4 compatible temperature sensors can be configured
in devicetree by providing a generic "jedec,jc-42.4-temp" binding.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
By converting the driver to regmap, we can use regmap to cache non-volatile
registers. Stop caching the temperature register; while potentially reading
it more often can result in reading it more often than necessary, this is
offset by the gain due to not re-reading the limit registers.
A positive side effect of this change is that limit registers can now be
read and updated before the first temperature conversion is complete.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
So far the chip was forced into polarity 0, even if it was preconfigured
differently. Do not touch the polarity when configuring the chip.
Also, the configuration register was read beack to check if the
configuration 'sticks'. Ultimately, that is similar to checking if the
chip is a tmp102 in the first place. Checking if a write into the
configuration register was successful is really not the way to do it,
and quite risky if the chip is not a tmp102, so drop that check.
Instead, verify if the configuration register has unexpected bits set
before writing into it.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If the chip was in shutdown mode when the driver was loaded, the first
conversion is ready no more than 35 milli-seconds after the chip was
taken out of shutdown. The driver delay was so far set to 333 ms (HZ / 3),
which is much higher than the maximum time needed by the chip.
Reduce the time to 35 milli-seconds.
Introduce a 'valid' flag to ensure that sensor data is actually read
even if requested less than 333 ms after the driver was loaded.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Return both error code and register value as return code from
read functions, and always check for errors.
This reduces code size on x86_64 by more than 1k while at
the same time improving error resiliency.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since all other cleanup handled with devm_add_action, we can use
devm_hwmon_device_register_with_groups() to register the hwmon
device, and drop the remove function.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use regmap. Leave caching to regmap and drop the register
update function. While this can result in additional read operations
if the temperature register is read continuously, it avoids re-reading
the limit registers and thus overall reduces complexity.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
lm75_read_value and lm75_write_value don't really add any value.
Replace with direct smbus access functions.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_add_action() to register the function to restore the original
chip configuration. Use devm_hwmon_device_register_with_groups()
to register the hwmon device, and drop the remove function as no
longer needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In 2011, commit 774466add7 ("hwmon: (jc42) Change detection class")
changed the detection class of these chips to I2C_CLASS_SPD based
on this premise: "makes more sense because these chips always live on
memory modules"
Today these chips have applications beyond memory modules. Examples are
JC42.4 compatible chips such as MCP9804 and MCP9808, but also MCP9805,
which is marked as JC42.4 compliant and suggested for use not only for
DIMMS, but also as generic temperature sensor.
Add I2C_CLASS_HWMON as an additional detection class to allow detection
by hwmon class i2c adapters.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
By registering a cleanup function with devm_add_action(), we can
simplify the error path in the probe function and drop the remove
function entirely.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MCP9808 is not officially compliant to JC-42, similar to MCP9804,
but its registers are compatible to JC-42.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The result of an integer divide by an unsigned is undefined.
This causes unexpected results when writing negative values
into the limit registers.
Maintain the shunt_resistors variables as signed integer to avoid
the problem. Also, for simplicity and ease of use, clamp shunt
resistor value on writes instead of rejecting bad values.
Cc: Andrew F. Davis <afd@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
trivial fix to spelling mistake in dev_dbg message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This allow us to debug how long take each SMM call and how long is system
frozen in SMM handler.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some Dell machines (e.g. Dell Precision M3800) have two fans, first with
index=0 and second with index=2. So export also attributes for third fan
device with index=2.
Reported-by: Tolga Cakir <cevelnet@gmail.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Tolga Cakir <cevelnet@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
The update_lock mutex is not used, so remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the the INA3221 26v capable, Triple channel,
Bi-Directional, Zero-Drift, Low-/High-Side, Current/Voltage Monitor
with I2C interface.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver implements support for the Sensirion SHT3x-DIS chip,
a humidity and temperature sensor. Temperature is measured
in degrees celsius, relative humidity is expressed as a percentage.
In the sysfs interface, all values are scaled by 1000,
i.e. the value for 31.5 degrees celsius is 31500.
Signed-off-by: Pascal Sachs <pascal.sachs@sensirion.com>
[groeck: Fixed 'Variable length array is used' gcc warning]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On more Dell machines (e.g. Dell Precision M3800) fan_type() call is too
expensive (CPU is too long in SMM mode) and cause kernel to hang. This is
bug in Dell SMM or BIOS.
This patch caches type for each fan (as it should not change) and changes
the way how fan presense is detected. First it try function fan_status()
as was before commit f989e55452 ("i8k: Add support for fan labels"). And
if that fails fallback to fan_type(). *_status() functions can fail in case
fan is not currently accessible (e.g. present on GPU which is currently
turned off).
Reported-by: Tolga Cakir <cevelnet@gmail.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=112021
Cc: stable@vger.kernel.org # v4.0+, will need backport
Tested-by: Tolga Cakir <cevelnet@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some Dell machines have especially broken SMM or BIOS which cause that once
fan_type() is called then CPU fan speed going randomly up and down. And for
fixing this behaviour reboot is required.
So this patch creates fan_type blacklist of affected Dell machines and
disallow fan_type() call on them to prevent that erratic behaviour.
Old blacklist which disabled loading driver on some machines added in
commits a4b45b25f1 ("hwmon: (dell-smm) Blacklist Dell Studio XPS 8100")
and 6220f4ebd7 ("hwmon: (dell-smm) Blacklist Dell Studio XPS 8000") were
moved to FAN_TYPE blacklist.
Reported-by: Jan C Peters <jcpeters89@gmail.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=100121
Cc: stable@vger.kernel.org # v4.0+, will need backport
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For security reasons ordinary user must not be able to control fan speed
via /proc/i8k by default. Some malicious software running under "nobody"
user could be able to turn fan off and cause HW problems. So this patch
changes default value of "restricted" parameter to 1.
Also restrict reading of DMI_PRODUCT_SERIAL from /proc/i8k via "restricted"
parameter. It is because non root user cannot read DMI_PRODUCT_SERIAL from
sysfs file /sys/class/dmi/id/product_serial.
Old non secure behaviour of file /proc/i8k can be achieved by loading this
module with "restricted" parameter set to 0.
Note that this patch has effects only for kernels compiled with CONFIG_I8K
and only for file /proc/i8k. Hwmon interface provided by this driver was
not changed and root access for setting fan speed was needed also before.
Reported-by: Mario Limonciello <Mario_Limonciello@dell.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org # will need backport
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ABI of I8K_BIOS_VERSION ioctl can return only number. But new BIOS versions
contain also other characters, which does not fit into that ABI. So in case
of non digit values return -EINVAL.
Reported-by: Mario Limonciello <Mario_Limonciello@dell.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
.alert() is meant to be generic, but there is currently no way
for the device driver to know which protocol generated the alert.
Add a parameter in .alert() to help the device driver to understand
what is given in data.
This patch is required to have the support of SMBus Host Notify protocol
through .alert().
Tested-by: Andrew Duggan <aduggan@synaptics.com>
For hwmon:
Acked-by: Guenter Roeck <linux@roeck-us.net>
For IPMI:
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The code handles this variable always as unsigned, so adapt the type.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We need to read a bunch of registers on each compute unit and possibly
on the current CPU too. Disable preemption around it. Otherwise, you
get:
BUG: using smp_processor_id() in preemptible [00000000] code: systemd-udevd/327
caller is read_registers+0x6a/0x110 [fam15h_power]
CPU: 3 PID: 327 Comm: systemd-udevd Not tainted 4.7.0-rc1+ #4
Hardware name: HP HP EliteBook 745 G3/807E, BIOS N73 Ver. 01.08 01/28/2016
...
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Rui Huang <ray.huang@amd.com>
Cc: Sherry Hurwitz <sherry.hurwitz@amd.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Huang Rui <ray.huang@amd.com>
Tested-by: Huang Rui <ray.huang@amd.com>
Fixes: fa79434499 ("hwmon: (fam15h_power) Add compute unit accumulated power")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull hwmon fixlets from Jean Delvare.
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
Documentation/hwmon: Update links in max34440
hwmon: (emc2103) Fix typo in MODULE_PARM_DESC
Pull thermal management updates from Zhang Rui:
- Introduce generic ADC thermal driver, based on OF thermal (Laxman
Dewangan)
- Introduce new thermal driver for Tango chips (Marc Gonzalez)
- Rockchip driver support for RK3399, RK3366, and some fixes (Caesar
Wang, Elaine Zhang and Shawn Lin)
- Add CPU power cooling model to Mediatek thermal driver (Dawei Chien)
- Wider usage of dev_thermal_zone_of_sensor_register (Eduardo Valentin)
- TI thermal driver gained a new maintainer (Keerthy).
- Enabled powerclamp driver by checking CPU feature and package cstate
counter instead of CPU whitelist (Jacob Pan)
- Various fixes on thermal governor, OF thermal, Tegra, and RCAR
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (50 commits)
thermal: tango: initialize TEMPSI_CFG
thermal: rockchip: use the usleep_range instead of udelay
thermal: rockchip: add the notes for better reading
thermal: rockchip: Support RK3366 SoCs in the thermal driver
thermal: rockchip: handle the power sequence for tsadc controller
thermal: rockchip: update the tsadc table for rk3399
thermal: rockchip: fixes the code_to_temp for tsadc driver
thermal: rockchip: disable thermal->clk in err case
thermal: tegra: add Tegra132 specific SOC_THERM driver
thermal: fix ptr_ret.cocci warnings
thermal: mediatek: Add cpu dynamic power cooling model.
thermal: generic-adc: Add ADC based thermal sensor driver
thermal: generic-adc: Add DT binding for ADC based thermal sensor
thermal: tegra: fix static checker warning
thermal: tegra: mark PM functions __maybe_unused
thermal: add temperature sensor support for tango SoC
thermal: hisilicon: fix IRQ imbalance enabling
thermal: hisilicon: support to use any sensor
thermal: rcar: Remove binding docs for r8a7794
thermal: tegra: add PM support
...
This set of changes introduces an atomic API to the PWM subsystem. This
is influenced by the DRM atomic API that was introduced a while back,
though it is obviously a lot simpler. The fundamental idea remains the
same, though: drivers provide a single callback to implement the atomic
configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware. Many
use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are postponed
to v4.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sxT9
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes introduces an atomic API to the PWM subsystem.
This is influenced by the DRM atomic API that was introduced a while
back, though it is obviously a lot simpler. The fundamental idea
remains the same, though: drivers provide a single callback to
implement the atomic configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware.
Many use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are
postponed to v4.8"
* tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
pwm: Add information about polarity, duty cycle and period to debugfs
pwm: Switch to the atomic API
pwm: Update documentation
pwm: Add core infrastructure to allow atomic updates
pwm: Add hardware readout infrastructure
pwm: Move the enabled/disabled info into pwm_state
pwm: Introduce the pwm_state concept
pwm: Keep PWM state in sync with hardware state
ARM: Explicitly apply PWM config extracted from pwm_args
drm: i915: Explicitly apply PWM config extracted from pwm_args
input: misc: pwm-beeper: Explicitly apply PWM config extracted from pwm_args
input: misc: max8997: Explicitly apply PWM config extracted from pwm_args
backlight: lm3630a: explicitly apply PWM config extracted from pwm_args
backlight: lp855x: Explicitly apply PWM config extracted from pwm_args
backlight: lp8788: Explicitly apply PWM config extracted from pwm_args
backlight: pwm_bl: Use pwm_get_args() where appropriate
fbdev: ssd1307fb: Use pwm_get_args() where appropriate
regulator: pwm: Use pwm_get_args() where appropriate
leds: pwm: Use pwm_get_args() where appropriate
input: misc: max77693: Use pwm_get_args() where appropriate
...
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: lm-sensors@lm-sensors.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Arnd Bergmann