With spidev the mesg->complete callback points to spidev_complete.
Calling this unblocks spidev_sync and so spidev_sync_write finishes. As
the struct spi_message just read is a local variable in
spidev_sync_write and recording the trace event accesses this message
the recording is better done first. The same can happen for
spidev_sync_read.
This fixes an oops observed on a 3.14-rt system with spidev activity
after
echo 1 > /sys/kernel/debug/tracing/events/spi/enable
.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Some devices samples state of the chip select signal during power up
and act differently based on this state, so SPI core should ensure
that CS line is driven in non-active state after spi_setup().
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All SPI drivers have been converted from legacy suspend/resume callbacks to
dev_pm_ops. So we can finally remove support for legacy PM from the SPI
core.
Since there aren't any special bus specific things to do during
suspend/resume and since the PM core will automatically fallback directly to
using the device's PM ops if no bus PM ops are specified there is no need to
have any special SPI bus PM ops.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This callback would be useful to handle an error that occurs in the generic
implementation of transfer_one_message(). The good candidate for this is to
drain FIFO and / or to terminate DMA transfers when timeout happened.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int, this
patch changes the type of m from int to unsigned long.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lots of activity in the devicetree code for v3.18. Most of it is related
to getting all of the overlay support code in place, but there are other
important things in there.
There are a few trivial merge conflicts. They shouldn't give you any
trouble.
Highlights:
- OF_RECONFIG notifiers for SPI, I2C and Platform devices. Those
subsystems can now respond to live changes to the device tree.
- CONFIG_OF_OVERLAY method for applying live changes to the device tree
- Removal of the of_allnodes list. This used to be used to iterate over
all the nodes in the device tree, but it is unnecessary because the
same thing can be done by iterating over the list of child pointers.
Getting rid of of_allnodes saves some memory and avoids the
possibility of of_allnodes being sorted differently from the child
lists.
- Support for retrieving original DTB blob via sysfs. Needed by kexec.
- More unittests
- Documentation and minor bug fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUiaTJAAoJEMWQL496c2LNdKkP/1rk20JXzJc948Z3VFZPXkzf
TUKXC+Qn0FmVjQhESkx6LxLDrMDTQlQLlWBmFuWRB87Fk5E32FEf5zzW7I9oQPS4
msIqJoYf5T7EPlmJ/85156xjK5ezc0OyoKEizn23mcKrJE4bmXQEbVw99UUFhq4R
Oz1a1ZPQQSSaMteKftOoRBiE3bJut3tJ3dfufNjwOuXi5rALJ0DVxuOeU/Hba13d
t05qlImwocKXGBDd/B4psBI5fZl4Tf4AmGOD9aU7YHxrLg4jOCbvqies3DQQ0q3D
o9YZBnuBw7A3tzJJ3F5KajRnFLazJBOV5BKGo7eYuTzT56mpZW/HF6eS9b1DbP9x
4q71Vd5qhIuU9JsQAStfZ6pdx3FBXRNGpIXXfwzbCSdaePIuOKS17zvA/Iy5bWeA
2TyqgMuKZwnXOXxQesMZJYIw2IEnIyobzh0A1wAnvReyos/nHF/tha/SA/Jutq1s
+0gOkMlPW2EdpADmlfLPRSHgSqO8bfCPeNPihn672MS2dAv9H+XRLcoKuSNErhdl
1gYtnR7IK+Sl0KmMC5YoMvXPchkV5YS2qEp1f3p+ZmgcMSWyHHKMtf8VwjNTaSBU
e1AshH6HvmYEPt0cnntSMAxbw+N596QjkVp4RbHsLpyj7qeUVVY56/K/aiM7M69P
BvJkuewrhsAxyM2X2OsD
=ak0A
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree changes from Grant Likely:
"Lots of activity in the devicetree code for v3.18. Most of it is
related to getting all of the overlay support code in place, but there
are other important things in there.
Highlights:
- OF_RECONFIG notifiers for SPI, I2C and Platform devices. Those
subsystems can now respond to live changes to the device tree.
- CONFIG_OF_OVERLAY method for applying live changes to the device
tree
- Removal of the of_allnodes list. This used to be used to iterate
over all the nodes in the device tree, but it is unnecessary
because the same thing can be done by iterating over the list of
child pointers. Getting rid of of_allnodes saves some memory and
avoids the possibility of of_allnodes being sorted differently from
the child lists.
- Support for retrieving original DTB blob via sysfs. Needed by
kexec.
- More unittests
- Documentation and minor bug fixes"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux: (42 commits)
of: Delete unnecessary check before calling "of_node_put()"
of: Drop ->next pointer from struct device_node
spi: Check for spi_of_notifier when CONFIG_OF_DYNAMIC=y
of: support passing console options with stdout-path
of: add optional options parameter to of_find_node_by_path()
of: Add bindings for chosen node, stdout-path
of: Remove unneeded and incorrect MODULE_DEVICE_TABLE
ARM: dt: fix up PL011 device tree bindings
of: base, fix of_property_read_string_helper kernel-doc
of: remove select of non-existant OF_DEVICE config symbol
spi/of: Add OF notifier handler
spi/of: Create new device registration method and accessors
i2c/of: Add OF_RECONFIG notifier handler
i2c/of: Factor out Devicetree registration code
of/overlay: Add overlay unittests
of/overlay: Introduce DT overlay support
of/reconfig: Add OF_DYNAMIC notifier for platform_bus_type
of/reconfig: Always use the same structure for notifiers
of/reconfig: Add debug output for OF_RECONFIG notifiers
of/reconfig: Add empty stubs for the of_reconfig methods
...
In order to avoid the situation where the kthread is waiting for another
context to make the hardware idle let the message pump know if it's being
called from the worker thread context and if it isn't then defer to the
worker thread instead of idling the hardware immediately. This will ensure
that if this situation happens we block rather than busy waiting.
Signed-off-by: Mark Brown <broonie@kernel.org>
If we are using the standard SPI message pump (which all drivers should be
transitioning over to) then special case the message enqueue and instead of
starting the worker thread to push messages to the hardware do so in the
context of the caller if the controller is idle. This avoids a context
switch in the common case where the controller has a single user in a
single thread, for short PIO transfers there may be no need to context
switch away from the calling context to complete the transfer.
The code is a bit more complex than is desirable in part due to the need
to handle drivers not using the standard queue and in part due to handling
the various combinations of bus locking and asynchronous submission in
interrupt context.
It is still suboptimal since it will still wake the message pump for each
transfer in order to schedule idling of the hardware and if multiple
contexts are using the controller simultaneously a caller may end up
pumping a message for some random other thread rather than for itself,
and if the thread ends up deferring due to another context idling the
hardware then it will just busy wait. It can, however, have the benefit
of aggregating power up and down of the hardware when a caller performs
a series of transfers back to back without any need for the use of
spi_async().
Signed-off-by: Mark Brown <broonie@kernel.org>
cur_msg is updated under the queue lock and holds the message we are
currently processing. Since currently we only ever do removals in the
pump kthread it doesn't matter in what order we do things but we want
to be able to push things out from the submitting thread so pull the
check to see if we're currently handling a message before we check to
see if the queue is idle.
Signed-off-by: Mark Brown <broonie@kernel.org>
Since most devices now do use the standard queue and in order to avoid
initialisation ordering issues being introduced by further refactorings
to improve performance move the initialisation of the queue and the lock
for it to the main master allocation.
Signed-off-by: Mark Brown <broonie@kernel.org>
kthread_run() could return ERR_PTR(-EINTR) from kthread_create_on_node().
Return the actual error code in spi_init_queue() instead of mangling it to
-ENOMEM.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add OF notifier handler needed for creating/destroying spi devices
according to dynamic runtime changes in the DT live tree. This code is
enabled when CONFIG_OF_DYNAMIC is selected.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Cc: <linux-spi@vger.kernel.org>
Dynamically inserting spi device nodes requires the use of a single
device registration method. Refactor the existing
of_register_spi_devices() to split out the core functionality for a
single device into a separate function; of_register_spi_device(). This
function will be used by the OF_DYNAMIC overlay code to make live
modifications to the tree.
Methods to lookup a device/master using a device node are added
as well, of_find_spi_master_by_node() & of_find_spi_device_by_node().
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
[grant.likely] Split patch into two pieces for clarity
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Cc: <linux-spi@vger.kernel.org>
We can only use page_address on memory that has been mapped using kmap,
when the buffer passed to the SPI has been allocated by vmalloc the page
has not necessarily been mapped through kmap. This means sometimes
page_address will return NULL causing the pointer we pass to sg_set_buf
to be invalid.
As we only call page_address so that we can pass a virtual address to
sg_set_buf which will then immediately call virt_to_page on it, fix this
by calling sg_set_page directly rather then relying on the sg_set_buf
helper.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
- Rework the handling of wakeup IRQs by the IRQ core such that
all of them will be switched over to "wakeup" mode in
suspend_device_irqs() and in that mode the first interrupt
will abort system suspend in progress or wake up the system
if already in suspend-to-idle (or equivalent) without executing
any interrupt handlers. Among other things that eliminates the
wakeup-related motivation to use the IRQF_NO_SUSPEND interrupt
flag with interrupts which don't really need it and should not
use it (Thomas Gleixner and Rafael J Wysocki).
- Switch over ACPI to handling wakeup interrupts with the help
of the new mechanism introduced by the above IRQ core rework
(Rafael J Wysocki).
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during
enumeration (Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in
the METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot
(or after resume from system suspend) and rework the ACPI Smart
Battery Subsystem (SBS) driver to work correctly with Apple
platforms (Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the
code, adding support for 133MHz I2C source clock on Intel Baytrail
to it and making it avoid using UART RTS override with Auto Flow
Control (Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak).
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin).
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui).
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes).
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name
change among other things), ppc-corenet, powernv (Viresh Kumar,
Preeti U Murthy, Shilpasri G Bhat, Lucas Stach).
- cpuidle support for DT-based idle states infrastructure, new
ARM64 cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi,
Rasmus Villemoes).
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman).
- Rework of the test_suspend kernel command line argument and
a new trace event for console resume (Srinivas Pandruvada,
Todd E Brandt).
- Second attempt to optimize swsusp_free() (hibernation core) to
make it avoid going through all PFNs which may be way too slow on
some systems (Joerg Roedel).
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS
entry update in MAINTAINERS (Heiko Stübner, Kevin Hilman).
- PM core fix related to clock management (Geert Uytterhoeven).
- PM core's sysfs code cleanup (Johannes Berg).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJUNbJoAAoJEILEb/54YlRxRp8QAJyGIPdx+f03oBir+7vvEwhY
svxd+V9xXK0UgWNGkCvlMk/1RIVy0qqtXliUrDaE+9tcHACA9+iAxMmNmDsjLOiO
gpazuz5kgeznrmp1eNwQnYTt+OCReQIcyCsj4q4fNo9bbETTyr2bRz226LEuZekC
TAiKdphYoOszFBgTVg5gfu+lqjHyXjgXPnwMTlRYn1y4YL2adDIgxj9cFedykTTW
Eu593TY2dH6ovERJ6q3qxZbRuWuxtww95J07b3t2/2Eb3e/R/zlX0/XJ/C88f/m2
DkqngbOYqCdw+zJeN6k8631foyfUwAcTd0sJ1+5nsm5H4NE5NqObjbxOk5/yNht6
HgvgISGHWLerEw+A/Dk6o0oZOtR1G/TAQ5qQk5nUfKT/sSoU+9/USsXtWhXwZCia
XccnJgW6ZtPrJJP3zDnkrxe3gndmLic11QXArw2IhWTsq0sZlAyMgtauBXLdDiQa
H/AMiYrUNmIABef1cirBLTtgXN4Zbsai9vIrxMmV7OgBrclrh52NTjzr05P5Hnl2
fRK56mb6mP59LymI7n8fyXL8tHnbNwFvTaxuvrZmzcYbzL0l9DuPocJrrTHRSfhm
GFfzfvLj0R66ZM4PthRSwz4H2v1FnlRcCkj5k/QjtBPlyzxtOnJveqve5umbrnb9
T5mRmlAs4iYwLuKCVVNT
=sIv/
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"Features-wise, to me the most important this time is a rework of
wakeup interrupts handling in the core that makes them work
consistently across all of the available sleep states, including
suspend-to-idle. Many thanks to Thomas Gleixner for his help with
this work.
Second is an update of the generic PM domains code that has been in
need of some care for quite a while. Unused code is being removed, DT
support is being added and domains are now going to be attached to
devices in bus type code in analogy with the ACPI PM domain. The
majority of work here was done by Ulf Hansson who also has been the
most active developer this time.
Apart from this we have a traditional ACPICA update, this time to
upstream version 20140828 and a few ACPI wakeup interrupts handling
patches on top of the general rework mentioned above. There also are
several cpufreq commits including renaming the cpufreq-cpu0 driver to
cpufreq-dt, as this is what implements generic DT-based cpufreq
support, and a new DT-based idle states infrastructure for cpuidle.
In addition to that, the ACPI LPSS driver is updated, ACPI support for
Apple machines is improved, a few bugs are fixed and a few cleanups
are made all over.
Finally, the Adaptive Voltage Scaling (AVS) subsystem now has a tree
maintained by Kevin Hilman that will be merged through the PM tree.
Numbers-wise, the generic PM domains update takes the lead this time
with 32 non-merge commits, second is cpufreq (15 commits) and the 3rd
place goes to the wakeup interrupts handling rework (13 commits).
Specifics:
- Rework the handling of wakeup IRQs by the IRQ core such that all of
them will be switched over to "wakeup" mode in suspend_device_irqs()
and in that mode the first interrupt will abort system suspend in
progress or wake up the system if already in suspend-to-idle (or
equivalent) without executing any interrupt handlers. Among other
things that eliminates the wakeup-related motivation to use the
IRQF_NO_SUSPEND interrupt flag with interrupts which don't really
need it and should not use it (Thomas Gleixner and Rafael Wysocki)
- Switch over ACPI to handling wakeup interrupts with the help of the
new mechanism introduced by the above IRQ core rework (Rafael Wysocki)
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during enumeration
(Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in the
METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot (or
after resume from system suspend) and rework the ACPI Smart Battery
Subsystem (SBS) driver to work correctly with Apple platforms
(Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the code,
adding support for 133MHz I2C source clock on Intel Baytrail to it
and making it avoid using UART RTS override with Auto Flow Control
(Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak)
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin)
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui)
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes)
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name change
among other things), ppc-corenet, powernv (Viresh Kumar, Preeti U
Murthy, Shilpasri G Bhat, Lucas Stach)
- cpuidle support for DT-based idle states infrastructure, new ARM64
cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi, Rasmus
Villemoes)
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman)
- Rework of the test_suspend kernel command line argument and a new
trace event for console resume (Srinivas Pandruvada, Todd E Brandt)
- Second attempt to optimize swsusp_free() (hibernation core) to make
it avoid going through all PFNs which may be way too slow on some
systems (Joerg Roedel)
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS entry
update in MAINTAINERS (Heiko Stübner, Kevin Hilman)
- PM core fix related to clock management (Geert Uytterhoeven)
- PM core's sysfs code cleanup (Johannes Berg)"
* tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (105 commits)
ACPI / fan: printk replacement
PM / clk: Fix crash in clocks management code if !CONFIG_PM_RUNTIME
PM / Domains: Rename cpu_data to cpuidle_data
cpufreq: cpufreq-dt: fix potential double put of cpu OF node
cpufreq: cpu0: rename driver and internals to 'cpufreq_dt'
PM / hibernate: Iterate over set bits instead of PFNs in swsusp_free()
cpufreq: ppc-corenet: remove duplicate update of cpu_data
ACPI / sleep: Rework the handling of ACPI GPE wakeup from suspend-to-idle
PM / sleep: Rename platform suspend/resume functions in suspend.c
PM / sleep: Export dpm_suspend_late/noirq() and dpm_resume_early/noirq()
ACPICA: Introduce acpi_enable_all_wakeup_gpes()
ACPICA: Clear all non-wakeup GPEs in acpi_hw_enable_wakeup_gpe_block()
ACPI / video: check _DOD list when creating backlight devices
PM / Domains: Move dev_pm_domain_attach|detach() to pm_domain.h
cpufreq: Replace strnicmp with strncasecmp
cpufreq: powernv: Set the cpus to nominal frequency during reboot/kexec
cpufreq: powernv: Set the pstate of the last hotplugged out cpu in policy->cpus to minimum
cpufreq: Allow stop CPU callback to be used by all cpufreq drivers
PM / devfreq: exynos: Enable building exynos PPMU as module
PM / devfreq: Export helper functions for drivers
...
The commit 46420dd73b (PM / Domains: Add APIs to attach/detach a PM
domain for a device) started using errno values in pm.h header file.
It also failed to include the header for these, thus it caused
compiler errors.
Instead of including the errno header to pm.h, let's move the functions
to pm_domain.h, since it's a better match.
Fixes: 46420dd73b (PM / Domains: Add APIs to attach/detach a PM domain for a device)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since we cannot make sure the 'n' will always be none zero here, and
then if either equal to zero, the kzalloc() will return ZERO_SIZE_PTR,
which equals to ((void *)16).
So this patch fix this with just doing the zero check before calling
kzalloc().
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously only the ACPI PM domain was supported by the spi bus.
Let's convert to the common attach/detach functions for PM domains,
which currently means we are extending the support to include the
generic PM domain as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Client drivers such as the ChomeOS EC driver sometimes use transfers with
no buffers and only a delay specified in order to allow a delay after the
assertion of /CS. Rather than require controller drivers handle this noop
case gracefully put checks in the core to ensure that we don't call into
the controller for such transfers.
Reported-by: Addy Ke <addy.ke@rock-chips.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
These are all arguments or fields that got added without updating the
kerneldoc comments.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A quiet release, more bug fixes than anything else. A few things do
stand out though:
- Updates to several drivers to move towards the standard GPIO chip
select handling in the core.
- DMA support for the SH MSIOF driver.
- Support for Rockchip SPI controllers (their first mainline
submission).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=u37g
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A quiet release, more bug fixes than anything else. A few things do
stand out though:
- updates to several drivers to move towards the standard GPIO chip
select handling in the core.
- DMA support for the SH MSIOF driver.
- support for Rockchip SPI controllers (their first mainline
submission)"
* tag 'spi-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (64 commits)
spi: davinci: use spi_device.cs_gpio to store gpio cs per spi device
spi: davinci: add support to configure gpio cs through dt
spi/pl022: Explicitly truncate large bitmask
spi/atmel: Fix pointer to int conversion warnings on 64 bit builds
spi: davinci: fix to support more than 2 chip selects
spi: topcliff-pch: don't hardcode PCI slot to get DMA device
spi: orion: fix incorrect handling of cell-index DT property
spi: orion: Fix error return code in orion_spi_probe()
spi/rockchip: fix error return code in rockchip_spi_probe()
spi/rockchip: remove redundant dev_err call in rockchip_spi_probe()
spi/rockchip: remove duplicated include from spi-rockchip.c
ARM: dts: fix the chip select gpios definition in the SPI nodes
spi: s3c64xx: Update binding documentation
spi: s3c64xx: use the generic SPI "cs-gpios" property
spi: s3c64xx: Revert "spi: s3c64xx: Added provision for dedicated cs pin"
spi: atmel: Use dmaengine_prep_slave_sg() API
spi: topcliff-pch: Update error messages for dmaengine_prep_slave_sg() API
spi: sh-msiof: Use correct device for DMA mapping with IOMMU
spi: sh-msiof: Handle dmaengine_prep_slave_single() failures gracefully
spi: rspi: Handle dmaengine_prep_slave_sg() failures gracefully
...
This patch adds helper functions to configure clock parents and rates
as specified through 'assigned-clock-parents', 'assigned-clock-rates'
DT properties for a clock provider or clock consumer device.
The helpers are now being called by the bus code for the platform, I2C
and SPI busses, before the driver probing and also in the clock core
after registration of a clock provider.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
According to Documentation/dmaengine.txt, scatterlists must be mapped
using the DMA struct device.
However, "dma_chan.dev->device" is the sysfs class device's device.
Use "dma_chan.device->dev" instead, which is the real DMA device's device.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
According to Documentation/DMA-API.txt, dma_map_sg() returns 0 on failure.
As spi_map_buf() returns an error code, convert zero into -ENOMEM.
Keep the existing check for negative numbers just in case.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Let memory subsystem handle the error logging.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Reviewed-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Rejecting unsupported values of spi-tx-bus-width and spi-rx-bus-width
may break compatibility with future DTs. Just ignore them, falling back
to Single SPI Transfers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
If we fail to create the master queue for some reason we should not attempt
to clean it up since attempting to stop a kthread that was not created will
hang and it's just generally bad practice. Unfortunately at present we call
spi_destroy_queue() even in cases where the creation fails.
Fix this by fixing the error handling in spi_master_initialize_queue() so
that we only flag the master as queued or destroy the queue if creation
succeeded. The change to the flag is done since the general master
cleanup uses this to destroy the queue.
Reported-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
If NO_DMA=y:
drivers/built-in.o: In function `spi_map_buf':
spi.c:(.text+0x21bc60): undefined reference to `dma_map_sg'
drivers/built-in.o: In function `spi_unmap_buf.isra.33':
spi.c:(.text+0x21c32e): undefined reference to `dma_unmap_sg'
make[3]: *** [vmlinux] Error 1
Protect the DMA code by #ifdef CONFIG_HAS_DMA to fix this:
- Extract __spi_map_msg() from spi_map_msg(),
- Provide dummy definitions of __spi_map_msg() and spi_unmap_msg() if
!CONFIG_HAS_DMA.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The availability of SPI Dual or Quad Transfer Mode as indicated by the
"spi-tx-bus-width" and "spi-rx-bus-width" properties in the device tree is
a hardware property of the SPI master, SPI slave, and board wiring. Hence
the SPI core should not reject an SPI slave because an SPI master driver
doesn't (yet) support Dual or Quad Transfer Mode.
Change the lack of Dual or Quad Transfer Mode support in the SPI master
driver from an error condition to a warning condition, and ignore the
unsupported mode bits, falling back to Single Transfer Mode, to avoid
breakages when running old kernels with new device trees.
Fixes: f477b7fb13 (spi: DUAL and QUAD support)
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
add optional property devicetree for SPI slave nodes
into devicetree so that LSB mode can be enabled by devicetree.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The existing timeout value in wait_for_completion_timeout is
calculated from the transfer length and speed with tolerance of 10msec.
This is too low because this is used for error conditions such as
hardware hang etc.
The xfer->speed_hz considered may not be the actual speed set
because the best clock divisor is chosen from a limited set such that
the actual speed <= requested speed. This will lead to timeout being
less than actual transfer time.
Considering acceptable latencies, this timeout can be set to a
value double the expected transfer plus 100 msecs.
This patch adds the same in the core.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The core implementation of cs_change didn't follow the documentation
which says that cs_change in the middle of the transfer means to briefly
deassert chip select, instead it followed buggy drivers which change the
polarity of chip select. Use a delay of 10us between deassert and
reassert simply from pulling numbers out of a hat.
Reported-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no real reason why we require transfers to have a completion and
the only user of the completion now checks to see if one has been provided
before using it so stop enforcing this. This makes it more convenient for
drivers to chain multiple asynchronous transfers together.
Signed-off-by: Mark Brown <broonie@linaro.org>
When xfer->speed_hz is greater than master->max_speed_hz, it's generally safe
to use master->max_speed_hz as transfer speed.
Thus use master->max_speed_hz as transfer speed rather than return error when
xfer->speed_hz > master->max_speed_hz.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
Zero length transfer becomes invalid since
"spi: core: Validate length of the transfers in message" commit,
but it should be valid to support an odd device, for example, which
requires long delay between chipselect and the first transfer, etc.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fixes below checkpatch warning:
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(10);
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SPI transfer length should be multiple of SPI word size,
where SPI word size should be power-of-two multiple
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
While backporting 33cf00e5 ("spi: attach/detach SPI device to the ACPI
power domain"), I noticed that the code changes were suboptimal:
* Why use &spi->dev when we have dev at hand?
* After fixing the above, spi is used only once, so we don't really
need a local variable for it.
This results in the following clean-up.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In __spi_validate(), xfer->speed_hz is set to be spi->max_speed_hz if it is not
set for this transfer. However, if spi->max_speed_hz is also not set,
xfer->speed_hz is 0. Some drivers (e.g. au1550, tegra114, tegra20-sflash,
tegra20-slink, etc.) then use below code to avoid setting xfer->speed_hz to 0.
/* Set speed to the spi max fequency if spi device has not set */
spi->max_speed_hz = spi->max_speed_hz ? : tspi->spi_max_frequency;
Let's handle it in spi core.
If spi->max_speed_hz is not set, make it default to spi->master->max_speed_hz.
So In __spi_validate() if both xfer->speed_hz and spi->max_speed_hz are not set,
xfer->speed_hz will be set to spi->master->max_speed_hz.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We cannot unconditionally use dma_map_single() to map data for use with
SPI since transfers may exceed a page and virtual addresses may not be
provided with physically contiguous pages. Further, addresses allocated
using vmalloc() need to be mapped differently to other addresses.
Currently only the MXS driver handles all this, a few drivers do handle
the possibility that buffers may not be physically contiguous which is
the main potential problem but many don't even do that. Factoring this
out into the core will make it easier for drivers to do a good job so if
the driver is using the core DMA code then generate a scatterlist
instead of mapping to a single address so do that.
This code is mainly based on a combination of the existing code in the MXS
and PXA2xx drivers. In future we should be able to extend it to allow the
core to concatenate adjacent transfers if they are compatible, improving
performance.
Currently for simplicity clients are not allowed to use the scatterlist
when they do DMA mapping, in the future the existing single address
mappings will be replaced with use of the scatterlist most likely as
part of pre-verifying transfers.
This change makes it mandatory to use scatterlists when using the core DMA
mapping so update the s3c64xx driver to do this when used with dmaengine.
Doing so makes the code more ugly but it is expected that the old s3c-dma
code can be removed very soon.
Signed-off-by: Mark Brown <broonie@linaro.org>
It is fairly common for SPI devices to require that one or both transfer
directions is always active. Currently drivers open code this in various
ways with varying degrees of efficiency. Start factoring this out by
providing flags SPI_MASTER_MUST_TX and SPI_MASTER_MUST_RX. These will cause
the core to provide buffers for the requested direction if none are
specified in the underlying transfer.
Currently this is fairly inefficient since we actually allocate a data
buffer which may get large, support for mapping transfers using a
scatterlist will allow us to avoid this for DMA based transfers.
Signed-off-by: Mark Brown <broonie@linaro.org>
The process of DMA mapping buffers for SPI transfers does not vary between
devices so in order to save duplication of code in drivers this can be
factored out into the core, allowing it to be integrated with the work that
is being done on factoring out the common elements from the data path
including more sharing of dmaengine code.
In order to use this masters need to provide a can_dma() operation and while
the hardware is prepared they should ensure that DMA channels are provided
in tx_dma and rx_dma. The core will then ensure that the buffers are mapped
for DMA prior to calling transfer_one_message().
Currently the cleanup on error is not complete, this needs to be improved.
Signed-off-by: Mark Brown <broonie@linaro.org>
Don't wait indefinitely for transfers to complete but time out after 10ms
more than we expect the transfer to take on the wire.
Signed-off-by: Mark Brown <broonie@linaro.org>
This reverts commit e120cc0dcf.
It causes a NULL pointer dereference with drivers using the generic
spi_transfer_one_message(), which always calls
spi_finalize_current_message(), which zeroes master->cur_msg.
Drivers implementing transfer_one_message() theirselves must always call
spi_finalize_current_message(), even if the transfer failed:
* @transfer_one_message: the subsystem calls the driver to transfer a single
* message while queuing transfers that arrive in the meantime. When the
* driver is finished with this message, it must call
* spi_finalize_current_message() so the subsystem can issue the next
* transfer
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
A respun version of the merges for the pull request previously sent with
a few additional fixes. The last two merges were fixed up by hand since
the branches have moved on and currently have the prior merge in them.
Quite a busy release for the SPI subsystem, mostly in cleanups big and
small scattered through the stack rather than anything else:
- New driver for the Broadcom BC63xx HSSPI controller.
- Fix duplicate device registration for ACPI.
- Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
changes upon which the transiton depends).
- Some small optimisations to reduce the amount of time we hold locks
in the datapath, eliminate some redundant checks and the size of a
spi_transfer.
- Lots of fixes, cleanups and general enhancements to drivers,
especially the rspi and Atmel drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CbUw
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A respun version of the merges for the pull request previously sent
with a few additional fixes. The last two merges were fixed up by
hand since the branches have moved on and currently have the prior
merge in them.
Quite a busy release for the SPI subsystem, mostly in cleanups big and
small scattered through the stack rather than anything else:
- New driver for the Broadcom BC63xx HSSPI controller
- Fix duplicate device registration for ACPI
- Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
changes upon which the transiton depends)
- Some small optimisations to reduce the amount of time we hold locks
in the datapath, eliminate some redundant checks and the size of a
spi_transfer
- Lots of fixes, cleanups and general enhancements to drivers,
especially the rspi and Atmel drivers"
* tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (112 commits)
spi: core: Fix transfer failure when master->transfer_one returns positive value
spi: Correct set_cs() documentation
spi: Clarify transfer_one() w.r.t. spi_finalize_current_transfer()
spi: Spelling s/finised/finished/
spi: sc18is602: Convert to use bits_per_word_mask
spi: Remove duplicate code to set default bits_per_word setting
spi/pxa2xx: fix compilation warning when !CONFIG_PM_SLEEP
spi: clps711x: Add MODULE_ALIAS to support module auto-loading
spi: rspi: Add missing clk_disable() calls in error and cleanup paths
spi: rspi: Spelling s/transmition/transmission/
spi: rspi: Add support for specifying CPHA/CPOL
spi/pxa2xx: initialize DMA channels to -1 to prevent inadvertent match
spi: rspi: Add more QSPI register documentation
spi: rspi: Add more RSPI register documentation
spi: rspi: Remove dependency on DMAE for SHMOBILE
spi/s3c64xx: Correct indentation
spi: sh: Use spi_sh_clear_bit() instead of open-coded
spi: bitbang: Grammar s/make to make/to make/
spi: sh-hspi: Spelling s/recive/receive/
spi: core: Improve tx/rx_nbits check comments
...
master->transfer_one returns positive value is not a error.
So set ret to 0 when master->transfer_one returns positive value.
Otherwise, I hit "spi_master spi0: failed to transfer one message from queue"
error when my transfer_one callback returns 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
ACPI enumerated devices has ACPI style _HID and _CID strings,
all of these strings can be used for both driver loading and matching.
Currently, in Platform, I2C and SPI bus, the ACPI style driver matching
is supported by invoking acpi_driver_match_device() in bus .match() callback.
But, the module autoloading is still broken.
For example, there is any ACPI device with _HID "INTABCD" that is
enumerated to platform bus, and we have a driver that can probe it.
The driver exports its module_alias as "acpi:INTABCD" use the following code
static const struct acpi_device_id xxx_acpi_match[] = {
{ "INTABCD", 0 },
{ }
};
MODULE_DEVICE_TABLE(acpi, xxx_acpi_match);
But, unfortunately, the device' modalias is shown as "platform:INTABCD:00",
please refer to modalias_show() and platform_uevent() in
drivers/base/platform.c.
This results in that the driver will not be loaded automatically when the
device node is created, because their modalias do not match.
This also applies to I2C and SPI bus.
With this patch, the device' modalias will be shown as "acpi:INTABCD" as well.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Rephrase the comments about tx/rx_nbits validity checks,
- Remove the stale comment about SPI_3WIRE (the code it refers to was
removed in commit 368ca4e0c7 ("spi:
Eliminate 3WIRE spi_transfer check")).
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit e13ac47bec (spi: Use stable dev_name for ACPI enumerated SPI
slaves) changed the SPI device naming to be based on ACPI device name
instead of carrying bus number and chip select for devices enumerated
from ACPI namespace.
In case of a buggy BIOS that lists multiple SPI devices sharing the same
chip select (even though they should use different) the current code fails
to detect that and allows the devices to be added to the bus.
Fix this by walking through the bus and comparing spi->chip_select instead
of device name. This should work regardless what the device name will be in
future.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This corrects a problem in spi_pump_messages() that leads to an spi
message hanging forever when a call to transfer_one_message() fails.
This failure occurs in my MCP2210 driver when the cs_change bit is set
on the last transfer in a message, an operation which the hardware does
not support.
Rationale
Since the transfer_one_message() returns an int, we must presume that it
may fail. If transfer_one_message() should never fail, it should return
void. Thus, calls to transfer_one_message() should properly manage a
failure.
Fixes: ffbbdd2132 (spi: create a message queueing infrastructure)
Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Checking for SPI_3WIRE isn't needed. spi_setup() already prevents 3WIRE
mode from being combined with DUAL or QUAD mode support. So there is no
need to differentiate between a single bit device with SPI_3WIRE set and
one with without. It doesn't change the allowed bit widths.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently we do a bunch of per-message validation and initialisation in
__spi_async() which is called with the bus lock held. Since none of this
validation depends on the current bus status there's no need to hold the
lock to do it so split it out into a separate __spi_validate() function
which is called prior to taking the bus lock.
This could be slightly neater but keep things simple for now to show the
code motion clearly.
Based on observations from Martin Sperl.
Signed-off-by: Mark Brown <broonie@linaro.org>
devres_add() should be called when the action to be undone succeeded,
not when it failed. Fix the inverted test in devm_spi_register_master()
which was doing the opposite.
The user-visible issue without this fix is:
insmod spi-tegra114.ko
Assume there's an MTD device on that SPI bus, which creates /dev/mtd0.
rmmod spi-tegra114
Doesn't remove devices on the SPI bus.
insmod spi-tegra114.ko
Creates a duplicate SPI device which creates /dev/mtd1.
hexdump -C /dev/mtd0
That's the old device, which uses an SPI bus hosted by a non-existent
module, which causes the oops below.
Unable to handle kernel paging request at virtual address bf0017c0
pgd = c0004000
[bf0017c0] *pgd=ad51b811, *pte=00000000, *ppte=00000000
Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM
...
PC is at 0xbf0017c0
LR is at spi_pump_messages+0x15c/0x204
pc : [<bf0017c0>] lr : [<c02f0af8>] psr: 60000113
...
Fixes: 666d5b4c74 ("spi: core: Add devm_spi_register_master()")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
- ACPI-based device hotplug fixes for issues introduced recently and
a fix for an older error code path bug in the ACPI PCI host bridge
driver.
- Fix for recently broken OMAP cpufreq build from Viresh Kumar.
- Fix for a recent hibernation regression related to s2disk.
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar.
- System suspend error code path fix related to runtime PM and
runtime PM documentation update from Ulf Hansson.
- cpufreq's conservative governor fix from Xiaoguang Chen.
- New processor IDs for intel_idle and turbostat and removal of
an obsolete Kconfig option from Len Brown.
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg.
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu.
- Rework of the ACPI companion representation in struct device and
code cleanup related to that change from Rafael J Wysocki,
Lan Tianyu and Jarkko Nikula.
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices
from Jarkko Nikula.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=QMp+
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
- ACPI-based device hotplug fixes for issues introduced recently and a
fix for an older error code path bug in the ACPI PCI host bridge
driver
- Fix for recently broken OMAP cpufreq build from Viresh Kumar
- Fix for a recent hibernation regression related to s2disk
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar
- System suspend error code path fix related to runtime PM and runtime
PM documentation update from Ulf Hansson
- cpufreq's conservative governor fix from Xiaoguang Chen
- New processor IDs for intel_idle and turbostat and removal of an
obsolete Kconfig option from Len Brown
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu
- Rework of the ACPI companion representation in struct device and code
cleanup related to that change from Rafael J Wysocki, Lan Tianyu and
Jarkko Nikula
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices from
Jarkko Nikula
* tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (24 commits)
PCI / hotplug / ACPI: Drop unused acpiphp_debug declaration
ACPI / scan: Set flags.match_driver in acpi_bus_scan_fixed()
ACPI / PCI root: Clear driver_data before failing enumeration
ACPI / hotplug: Fix PCI host bridge hot removal
ACPI / hotplug: Fix acpi_bus_get_device() return value check
cpufreq: governor: Remove fossil comment in the cpufreq_governor_dbs()
ACPI / video: clean up DMI table for initial black screen problem
ACPI / EC: Ensure lock is acquired before accessing ec struct members
PM / Hibernate: Do not crash kernel in free_basic_memory_bitmaps()
ACPI / AC: Remove struct acpi_device pointer from struct acpi_ac
spi: Use stable dev_name for ACPI enumerated SPI slaves
i2c: Use stable dev_name for ACPI enumerated I2C slaves
ACPI: Provide acpi_dev_name accessor for struct acpi_device device name
ACPI / bind: Use (put|get)_device() on ACPI device objects too
ACPI: Eliminate the DEVICE_ACPI_HANDLE() macro
ACPI / driver core: Store an ACPI device pointer in struct acpi_dev_node
cpufreq: OMAP: Fix compilation error 'r & ret undeclared'
PM / Runtime: Fix error path for prepare
PM / Runtime: Update documentation around probe|remove|suspend
cpufreq: conservative: set requested_freq to policy max when it is over policy max
...
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Current spi bus_num.chip_select "spix.y" based device naming scheme may not
be stable enough to be used in name based matching, for instance within
ALSA SoC subsystem.
This can be problem in PC kind of platforms if there are changes in SPI bus
configuration, amount of busses or probe order.
This patch addresses the problem by using the ACPI device name with
"spi-" prefix for ACPI enumerated SPI slave. For them device name
"spix.y" becomes "spi-INTABCD:ij".
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify struct acpi_dev_node to contain a pointer to struct acpi_device
associated with the given device object (that is, its ACPI companion
device) instead of an ACPI handle corresponding to it. Introduce two
new macros for manipulating that pointer in a CONFIG_ACPI-safe way,
ACPI_COMPANION() and ACPI_COMPANION_SET(), and rework the
ACPI_HANDLE() macro to take the above changes into account.
Drop the ACPI_HANDLE_SET() macro entirely and rework its users to
use ACPI_COMPANION_SET() instead. For some of them who used to
pass the result of acpi_get_child() directly to ACPI_HANDLE_SET()
introduce a helper routine acpi_preset_companion() doing an
equivalent thing.
The main motivation for doing this is that there are things
represented by struct acpi_device objects that don't have valid
ACPI handles (so called fixed ACPI hardware features, such as
power and sleep buttons) and we would like to create platform
device objects for them and "glue" them to their ACPI companions
in the usual way (which currently is impossible due to the
lack of valid ACPI handles). However, there are more reasons
why it may be useful.
First, struct acpi_device pointers allow of much better type checking
than void pointers which are ACPI handles, so it should be more
difficult to write buggy code using modified struct acpi_dev_node
and the new macros. Second, the change should help to reduce (over
time) the number of places in which the result of ACPI_HANDLE() is
passed to acpi_bus_get_device() in order to obtain a pointer to the
struct acpi_device associated with the given "physical" device,
because now that pointer is returned by ACPI_COMPANION() directly.
Finally, the change should make it easier to write generic code that
will build both for CONFIG_ACPI set and unset without adding explicit
compiler directives to it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> # on Haswell
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com> # for ATA and SDIO part
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from
Mika Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh Kumar,
Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz Majewski,
Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki,
Naresh Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani,
Zhang Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko,
Al Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=JCxk
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael J Wysocki:
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from Mika
Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh
Kumar, Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz
Majewski, Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki, Naresh
Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani, Zhang
Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko, Al
Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
* tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (386 commits)
cpufreq: conservative: fix requested_freq reduction issue
ACPI / hotplug: Consolidate deferred execution of ACPI hotplug routines
PM / runtime: Use pm_runtime_put_sync() in __device_release_driver()
ACPI / event: remove unneeded NULL pointer check
Revert "ACPI / video: Ignore BIOS initial backlight value for HP 250 G1"
ACPI / video: Quirk initial backlight level 0
ACPI / video: Fix initial level validity test
intel_pstate: skip the driver if ACPI has power mgmt option
PM / hibernate: Avoid overflow in hibernate_preallocate_memory()
ACPI / hotplug: Do not execute "insert in progress" _OST
ACPI / hotplug: Carry out PCI root eject directly
ACPI / hotplug: Merge device hot-removal routines
ACPI / hotplug: Make acpi_bus_hot_remove_device() internal
ACPI / hotplug: Simplify device ejection routines
ACPI / hotplug: Fix handle_root_bridge_removal()
ACPI / hotplug: Refuse to hot-remove all objects with disabled hotplug
ACPI / scan: Start matching drivers after trying scan handlers
ACPI: Remove acpi_pci_slot_init() headers from internal.h
ACPI / blacklist: fix name of ThinkPad Edge E530
PowerCap: Fix build error with option -Werror=format-security
...
Conflicts:
arch/arm/mach-omap2/opp.c
drivers/Kconfig
drivers/spi/spi.c
Fix the following checkpatch error and warnings.
ERROR: space required after that ',' (ctx:VxV)
WARNING: quoted string split across lines
WARNING: max() should probably be max_t(int, nb, master->num_chipselect)
WARNING: sizeof *spi should be sizeof(*spi)
WARNING: sizeof *master should be sizeof(*master)
WARNING: sizeof x should be sizeof(x)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The loops which SPI controller drivers use to process the list of transfers
in a spi_message are typically very similar and have some error prone areas
such as the handling of /CS. Help simplify drivers by factoring this code
out into the core - if drivers provide a transfer_one() function instead
of a transfer_one_message() function the core will handle processing at the
message level.
/CS can be controlled by either setting cs_gpio or providing a set_cs
function. If this is not possible for hardware reasons then both can be
omitted and the driver should continue to implement manual /CS handling.
This is a first step in refactoring and it is expected that there will be
further enhancements, for example factoring out of the mapping of transfers
for DMA and the initiation and completion of interrupt driven transfers.
Signed-off-by: Mark Brown <broonie@linaro.org>
Many SPI drivers perform setup and tear down on every message, usually
doing things like DMA mapping the message. Provide hooks for them to use
to provide such operations.
This is of limited value for drivers that implement transfer_one_message()
but will be of much greater utility with future factoring out of standard
implementations of that function.
Signed-off-by: Mark Brown <broonie@linaro.org>
If the SPI device is enumerated from ACPI namespace (it has an ACPI handle)
it might have ACPI methods that needs to be called in order to transition
the device to different power states (such as _PSx).
We follow what has been done for platform and I2C buses here and attach the
SPI device to the ACPI power domain if the device has an ACPI handle. This
makes sure that the device is powered on when its ->probe() is called.
For non-ACPI devices this patch is a no-op.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is a minor fault about ACPI enumerated SPI devices with their modalias
attribute. Now modalias is set by device instance not by hardware ID.
For example "spi:INTABCD:00", "spi:INTABCD:01" etc.
This means each device instance gets different modalias which does match
with generated modules.alias. Currently this is not problem as matching can
happen also with "acpi:INTABCD" modalias.
Fix this by using ACPI hardware ID.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The dev_attrs field of struct bus_type is going away soon, dev_groups
should be used instead. This converts the spi bus code to use the
correct field.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Provide tracepoints for the lifecycle of a message from submission to
completion and for the active time for masters to help with performance
analysis of SPI I/O.
Signed-off-by: Mark Brown <broonie@linaro.org>
Instead of getting the raw property, checking the length, and doing
endian conversion each time, use the OF function
of_property_read_u32() that does all that.
Error messages are slightly improved with error codes from
of_property_read_u32() for different ways the property may be invalid
(missing, too short, etc.)
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
request_module() can handle format strings on its own, no need to create
the full module name ourself.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Help simplify the cleanup code for SPI master drivers by providing a
managed master registration function, ensuring that the master is
automatically unregistered whenever the device is unbound.
Signed-off-by: Mark Brown <broonie@linaro.org>
spi: quad: fix the name of DT property in patch
The previous property name spi-tx-nbits and spi-rx-nbits looks not
human-readable. To make it consistent with other devices, using property
name spi-tx-bus-width and spi-rx-bus-width instead of the previous one
specify the number of data wires that spi controller will work in.
Add the specification in spi-bus.txt.
Signed-off-by: wangyuhang <wangyuhang2014@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the case spi_master_initialize_queue() fails, current code calls
device_unregister() before return error from spi_register_master().
However, all the drivers call spi_master_put() in the error path if
spi_register_master() fails. Thus we should call device_del() rather than
device_unregister() before return error from spi_register_master().
This also makes all the spi_register_master() error handling consistent,
because all other error paths of spi_register_master() expect drivers to
call spi_master_put() if spi_register_master() fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The addition SPI quad support made the DT properties mandatory, breaking
compatibility with existing systems. Fix that by making them optional,
also improving the error messages while we're at it.
Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Delete a "return" when commit the patch to a new kernel version
by mistake. So recover it.
Signed-off-by: wangyuhang <wangyuhang2014@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have tested master->running immediately after grab the master->queue_lock.
The status of master->running won't be changed until we release the lock.
Thus remove a redundant test for master->running.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a bug in the following patch:
http://comments.gmane.org/gmane.linux.kernel.spi.devel/14420
spi: DUAL and QUAD support
fix the previous patch some mistake below:
1. DT in slave node, use "spi-tx-nbits = <1/2/4>" in place of using
"spi-tx-dual, spi-tx-quad" directly, same to rx. So correct the
previous way to get the property in @of_register_spi_devices().
2. Change the value of transfer bit macro(SPI_NBITS_SINGLE, SPI_NBITS_DUAL
SPI_NBITS_QUAD) to 0x01, 0x02 and 0x04 to match the actual wires.
3. Add the following check
(1)keep the tx_nbits and rx_nbits in spi_transfer is not beyond the
single, dual and quad.
(2)keep tx_nbits and rx_nbits are contained by @spi_device->mode
example: if @spi_device->mode = DUAL, then tx/rx_nbits can not be set
to QUAD(SPI_NBITS_QUAD)
(3)if "@spi_device->mode & SPI_3WIRE", then tx/rx_nbits should be in
single(SPI_NBITS_SINGLE)
Checking of the tx/rx transfer bits and mode bits should be done conditionally
based on type of buffer filled else EINVAL condition will
always get hit either for rx or tx.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
fix the previous patch some mistake below:
1. DT in slave node, use "spi-tx-nbits = <1/2/4>" in place of using
"spi-tx-dual, spi-tx-quad" directly, same to rx. So correct the
previous way to get the property in @of_register_spi_devices().
2. Change the value of transfer bit macro(SPI_NBITS_SINGLE, SPI_NBITS_DUAL
SPI_NBITS_QUAD) to 0x01, 0x02 and 0x04 to match the actual wires.
3. Add the following check
(1)keep the tx_nbits and rx_nbits in spi_transfer is not beyond the
single, dual and quad.
(2)keep tx_nbits and rx_nbits are contained by @spi_device->mode
example: if @spi_device->mode = DUAL, then tx/rx_nbits can not be set
to QUAD(SPI_NBITS_QUAD)
(3)if "@spi_device->mode & SPI_3WIRE", then tx/rx_nbits should be in
single(SPI_NBITS_SINGLE)
Signed-off-by: wangyuhang <wangyuhang2014@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since the 'spi: Support transfer speed checking in the core'
change, the SPI core validates the desired speed of a given
transfer against the minimum and maximum speeds supported by
the controller.
If the speed of a transfer is not specified, the core uses
the maximum speed of the actual SPI device. However if the
maximum speed of the actual device is greater than the
maximum speed of the controller, the core will reject the
transfer due to the aforementioned change.
Change the code to use the maximum speed of the controller
by default if that is below the device's maximum speed.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Most SPI drivers that implement runtime PM support use identical code to
do so: they acquire a runtime PM lock in prepare_transfer_hardware() and
then they release it in unprepare_transfer_hardware(). The variations in
this are mostly missing error checking and the choice to use autosuspend.
Since these runtime PM calls are normally the only thing in the prepare
and unprepare callbacks and the autosuspend API transparently does the
right thing on devices with autosuspend disabled factor all of this out
into the core with a flag to enable the behaviour.
Signed-off-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Make spi core calculate the message length while
populating the other transfer parameters.
Usecase, driver can use it to populate framelength filed in their
controller.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Allow drivers to avoid implementing their own checks for simple rates by
specifying the limits in the master structure.
Signed-off-by: Mark Brown <broonie@linaro.org>
Merge first patch-bomb from Andrew Morton:
- various misc bits
- I'm been patchmonkeying ocfs2 for a while, as Joel and Mark have been
distracted. There has been quite a bit of activity.
- About half the MM queue
- Some backlight bits
- Various lib/ updates
- checkpatch updates
- zillions more little rtc patches
- ptrace
- signals
- exec
- procfs
- rapidio
- nbd
- aoe
- pps
- memstick
- tools/testing/selftests updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (445 commits)
tools/testing/selftests: don't assume the x bit is set on scripts
selftests: add .gitignore for kcmp
selftests: fix clean target in kcmp Makefile
selftests: add .gitignore for vm
selftests: add hugetlbfstest
self-test: fix make clean
selftests: exit 1 on failure
kernel/resource.c: remove the unneeded assignment in function __find_resource
aio: fix wrong comment in aio_complete()
drivers/w1/slaves/w1_ds2408.c: add magic sequence to disable P0 test mode
drivers/memstick/host/r592.c: convert to module_pci_driver
drivers/memstick/host/jmb38x_ms: convert to module_pci_driver
pps-gpio: add device-tree binding and support
drivers/pps/clients/pps-gpio.c: convert to module_platform_driver
drivers/pps/clients/pps-gpio.c: convert to devm_* helpers
drivers/parport/share.c: use kzalloc
Documentation/accounting/getdelays.c: avoid strncpy in accounting tool
aoe: update internal version number to v83
aoe: update copyright date
aoe: perform I/O completions in parallel
...
Calling kthread_run with a single name parameter causes it to be handled
as a format string. Many callers are passing potentially dynamic string
content, so use "%s" in those cases to avoid any potential accidents.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0. If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.
Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.
To reduce overall code bloat, make the changes described above.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
A fairly quiet release for SPI, mainly driver work. A few highlights:
- Supports bits per word compatibility checking in the core.
- Allow use of the IP used in Freescale SPI controllers outside
Freescale SoCs.
- DMA support for the Atmel SPI driver.
- New drivers for the BCM2835 and Tegra114.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=+Omc
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, mainly driver work. A few highlights:
- Supports bits per word compatibility checking in the core.
- Allow use of the IP used in Freescale SPI controllers outside
Freescale SoCs.
- DMA support for the Atmel SPI driver.
- New drivers for the BCM2835 and Tegra114"
* tag 'spi-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (68 commits)
spi-topcliff-pch: fix to use list_for_each_entry_safe() when delete list items
spi-topcliff-pch: missing platform_driver_unregister() on error in pch_spi_init()
ARM: dts: add pinctrl property for spi node for atmel SoC
ARM: dts: add spi nodes for the atmel boards
ARM: dts: add spi nodes for atmel SoC
ARM: at91: add clocks for spi dt entries
spi/spi-atmel: add dmaengine support
spi/spi-atmel: add flag to controller data for lock operations
spi/spi-atmel: add physical base address
spi/sirf: fix MODULE_DEVICE_TABLE
MAINTAINERS: Add git repository and update my address
spi/s3c64xx: Check for errors in dmaengine prepare_transfer()
spi/s3c64xx: Fix non-dmaengine usage
spi: omap2-mcspi: fix error return code in omap2_mcspi_probe()
spi/s3c64xx: let device core setup the default pin configuration
MAINTAINERS: Update Grant's email address and maintainership
spi: omap2-mcspi: Fix transfers if DMADEVICES is not set
spi: s3c64xx: move to generic dmaengine API
spi-gpio: init CS before spi_bitbang_setup()
spi: spi-mpc512x-psc: let transmiter/receiver enabled when in xfer loop
...
This makes sure that an error is returned on an incorrectly formed
"cs-gpios" property, but reports success when the "cs-gpios" property is
well formed or missing.
When holes in the cs-gpios property phandle list is used to indicate
that some other form of chipselect is to be used it is important that
failure to read a broken "cs-gpios" property does not silently fail
leading to the spi controller to use an unintended chipselect.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The return value from of_get_named_gpio is -ENOENT when the given index
matches a hole in the "cs-gpios" property phandle list. However, the
default value of cs_gpio in struct spi_device and entries of cs_gpios in
struct spi_master is -EINVAL, which is documented to indicate that a
GPIO line should not be used for the given spi_device.
This sets the default value of cs_gpio in struct spi_device and entries
of cs_gpios in struct spi_master to -ENOENT. Thus, -ENOENT is the only
value used to indicate that no GPIO line should be used.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
A bunch of small driver fixes plus a fix for error handling in the core
- nothing too exciting overall.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=eqgv
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v3.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull spi fixes from Mark Brown:
"A bunch of small driver fixes plus a fix for error handling in the
core - nothing too exciting overall."
* tag 'spi-fix-v3.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc:
spi/mpc512x-psc: optionally keep PSC SS asserted across xfer segmensts
spi: Unlock a spinlock before calling into the controller driver.
spi/s3c64xx: modified error interrupt handling and init
spi/bcm63xx: don't disable non enabled clocks in probe error path
spi/bcm63xx: Remove unused variable
spi: slink-tegra20: move runtime pm calls to transfer_one_message
The ACPI handle of struct spi_master's dev member should not be
set, because this causes that struct spi_master to be associated
with the ACPI device node corresponding to its parent as the
second "physical_device", which is incorrect (this happens during
the registration of struct spi_master). Consequently,
acpi_register_spi_devices() should use the ACPI handle of the
parent of the struct spi_master it is called for rather than that
struct spi_master's ACPI handle (which should be NULL).
Make that happen and modify the spi-pxa2xx driver, which currently is
the only driver for ACPI-enumerated SPI controller chips, not to set
the ACPI handle for the struct spi_master it creates.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
spi_pump_messages() calls into a controller driver with
unprepare_transfer_hardware() which is documented as "This may sleep".
As in the prepare_transfer_hardware() call below, we should release the
queue_lock spinlock before making the call.
Rework the logic a bit to hold queue_lock to protect the 'busy' flag,
then release it to call unprepare_transfer_hardware().
Signed-off-by: Bryan Freed <bfreed@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow SPI masters to define the set of bits_per_word values they support.
If they do this, then the SPI core will reject transfers that attempt to
use an unsupported bits_per_word value. This eliminates the need for each
SPI driver to implement this checking in most cases.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
All around device tree changes destined for v3.8. Aside from the
documentation updates the highlights in this branch include:
- Kbuild changes for using CPP with .dts files
- locking fix from preempt_rt patchset
- include DT alias names in device uevent
- Selftest bugfixes and improvements
- New function for counting phandles stanzas in a property
- constify argument to of_node_full_name()
- Various bug fixes
This tree did also contain a commit to use platform_device_add instead
of open-coding the device add code, but it caused problems with amba
devices and needed to be reverted.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Zlkx
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree changes from Grant Likely:
"All around device tree changes destined for v3.8. Aside from the
documentation updates the highlights in this branch include:
- Kbuild changes for using CPP with .dts files
- locking fix from preempt_rt patchset
- include DT alias names in device uevent
- Selftest bugfixes and improvements
- New function for counting phandles stanzas in a property
- constify argument to of_node_full_name()
- Various bug fixes
This tree did also contain a commit to use platform_device_add instead
of open-coding the device add code, but it caused problems with amba
devices and needed to be reverted."
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux: (23 commits)
Revert "of: use platform_device_add"
kbuild: limit dtc+cpp include path
gpio: Make of_count_named_gpios() use new of_count_phandle_with_args()
of: Create function for counting number of phandles in a property
of/base: Clean up exit paths for of_parse_phandle_with_args()
of/selftest: Use selftest() macro throughout
of/selftest: Fix GPIOs selftest to cover the 7th case
of: fix recursive locking in of_get_next_available_child()
documentation/devicetree: Fix a typo in exynos-dw-mshc.txt
OF: convert devtree lock from rw_lock to raw spinlock
of/exynos_g2d: Add Bindings for exynos G2D driver
kbuild: create a rule to run the pre-processor on *.dts files
input: Extend matrix-keypad device tree binding
devicetree: Move NS2 LEDs binding into LEDs directory
of: use platform_device_add
powerpc/5200: Fix size to request_mem_region() call
documentation/devicetree: Fix typos
of: add 'const' to of_node_full_name parameter
of: Output devicetree alias names in uevent
DT: add vendor prefixes for Renesas and Toshiba
...
Changes to both core spi code and spi device drivers. The driver
changes are the usual set of bug fixes and platform enablement. Core
code changes include:
- More intelligent assignment of SPI bus numbers when using DT
- Common mechanism for using gpios as CS lines
- Pull checks for bits_per_word and transfer speed out of drivers and
into core code
- Ensure temporary DMA buffers are DMA safe
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=DR18
-----END PGP SIGNATURE-----
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux
Pull SPI changes from Grant Likely:
"Changes to both core spi code and spi device drivers. The driver
changes are the usual set of bug fixes and platform enablement.
Core code changes include:
- More intelligent assignment of SPI bus numbers when using DT
- Common mechanism for using gpios as CS lines
- Pull checks for bits_per_word and transfer speed out of drivers and
into core code
- Ensure temporary DMA buffers are DMA safe"
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux: (50 commits)
spi: Document cs_gpios and cs_gpio in kernel-doc
spi/of: Fix initialization of cs_gpios array
spi/pxa2xx: add support for Lynxpoint SPI controllers
spi/pxa2xx: add support for Intel Low Power Subsystem SPI
spi/pxa2xx: add support for SPI_LOOP
spi/pxa2xx: add support for runtime PM
spi/pxa2xx: add support for DMA engine
spi/pxa2xx: break out the private DMA API usage into a separate file
spi/ath79: add shutdown handler
spi/mips-lantiq: set SPI_MASTER_HALF_DUPLEX flag
spi/mips-lantiq: make use of spi_finalize_current_message
spi/bcm63xx: work around inability to keep CS up
spi/davinci: use request_threaded_irq() to fix deadlock
spi/orion: Use module_platform_driver()
spi/bcm63xx: reject transfers unable to transfer
spi: Ensure memory used for spi_write_then_read() is DMA safe
spi/spi-mpc512x-psc: init mode bits supported by the driver
spi/mpc512x-psc: don't use obsolet cell-index property
spi: Remove erroneous __init, __exit and __exit_p() references in drivers
spi/s3c64xx: fix checkpatch warnings and error
...
This patch replaces the horribly coded of_count_named_gpios() with a
call to of_count_phandle_with_args() which is far more efficient. This
also changes the return value of of_gpio_count() & of_gpio_named_count()
from 'unsigned int' to 'int' so that it can return an error code. All
the users of that function are fixed up to correctly handle a negative
return value.
v2: Split GPIO portion into a separate patch
Tested-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Using memset does not set an array of integers properly. Replace with a
loop to set each element properly.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move rt scheduler definitions out of include/linux/sched.h into
new file include/linux/sched/rt.h
Signed-off-by: Clark Williams <williams@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20130207094707.7b9f825f@riff.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
All in-kernel users of class_find_device() don't really need mutable
data for match callback.
In two places (kernel/power/suspend_test.c, drivers/scsi/osd/osd_uld.c)
this patch changes match callbacks to use const search data.
The const is propagated to rtc_class_open() and power_supply_get_by_name()
parameters.
Note that there's a dev reference leak in suspend_test.c that's not
touched in this patch.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use GFP_DMA in order to ensure that the memory we allocate for transfers
in spi_write_then_read() can be DMAed. On most platforms this will have
no effect.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When spi client does the spi transfer and if it does not set
the speed for each transfer then set it as default
of spi device in spi core before calling low level transfer.
This will remove the extra check in low level driver for setting
speed.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Linux assigns a number to each spi_master in the system, but when the
platform used the device tree, the numbers are dynamically assigned and
are not predictable. In general this shouldn't matter since the kernel
doesn't use the bus number for anything other than matching a bus to
spi_boardinfo (not used for DT). However, sometimes userspace needs to
figure out which bus is which, so it makes sense to use the global
/aliases namespace to choose a specific bus number.
It is safe to derive the bus number from an alias because aliases will
never cause two buses to try and use the same bus number. (At one time
the cell-index property was used for this purpose, but cell-index has
the risk of an id collision).
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
To get modprobe to automatically load the proper modules, we need to
prefix things with "spi:". Partially based on Grant Likely's suggestions.
Signed-off-by: David Daney <david.daney@cavium.com>
[grant.likely: reworked because drivers/of/of_spi.c has been removed]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Primarily SPI device driver bug fixes, one removal of an old driver, and
some new tegra support. There is some core code change too, but all in
all pretty small stuff. The new features to note are:
- Common code for describing GPIO CS lines in the device tree
- Remove the SPI_BUFSIZ limitation on spi_write_the_read()
- core spi ensures bits_per_word is set correctly
- SPARC can now use SPI
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bvpH
-----END PGP SIGNATURE-----
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull SPI updates from Grant Likely:
"Primarily SPI device driver bug fixes, one removal of an old driver,
and some new tegra support. There is some core code change too, but
all in all pretty small stuff.
The new features to note are:
- Common code for describing GPIO CS lines in the device tree
- Remove the SPI_BUFSIZ limitation on spi_write_the_read()
- core spi ensures bits_per_word is set correctly
- SPARC can now use SPI"
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6: (36 commits)
spi/sparc: Allow of_register_spi_devices for sparc
spi: Remove HOTPLUG section attributes
spi: Add support for specifying 3-wire mode via device tree
spi: Fix comparison of different integer types
spi/orion: Add SPI_CHPA and SPI_CPOL support to kirkwood driver.
spi/sh: Add SH Mobile series as dependency to MSIOF controller
spi/sh-msiof: Remove unneeded clock name
spi: Remove SPI_BUFSIZ restriction on spi_write_then_read()
spi/stmp: remove obsolete driver
spi/clps711x: New SPI master driver
spi: omap2-mcspi: remove duplicate inclusion of linux/err.h
spi: omap2-mcspi: Fix the redifine warning
spi/sh-hspi: add CS manual control support
of_spi: add generic binding support to specify cs gpio
spi: omap2-mcspi: remove duplicated include from spi-omap2-mcspi.c
spi/bitbang: (cosmetic) simplify list manipulation
spi/bitbang: avoid needless loop flow manipulations
spi/omap: fix D0/D1 direction confusion
spi: tegra: add spi driver for sflash controller
spi: Dont call master->setup if not populated
...
* Introduction of device PM QoS flags.
* ACPI device power management update allowing subsystems other than
PCI to use it more easily.
* ACPI device enumeration rework allowing additional kinds of devices
to be enumerated via ACPI. From Mika Westerberg, Adrian Hunter,
Mathias Nyman, Andy Shevchenko, and Rafael J. Wysocki.
* ACPICA update to version 20121018 from Bob Moore and Lv Zheng.
* ACPI memory hotplug update from Wen Congyang and Yasuaki Ishimatsu.
* Introduction of acpi_handle_<level>() messaging macros and ACPI-based CPU
hot-remove support from Toshi Kani.
* ACPI EC updates from Feng Tang.
* cpufreq updates from Viresh Kumar, Fabio Baltieri and others.
* cpuidle changes to quickly notice governor prediction failure from
Youquan Song.
* Support for using multiple cpuidle drivers at the same time and cpuidle
cleanups from Daniel Lezcano.
* devfreq updates from Nishanth Menon and others.
* cpupower update from Thomas Renninger.
* Fixes and small cleanups all over the place.
--
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=6OEP
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
- Introduction of device PM QoS flags.
- ACPI device power management update allowing subsystems other than
PCI to use it more easily.
- ACPI device enumeration rework allowing additional kinds of devices
to be enumerated via ACPI. From Mika Westerberg, Adrian Hunter,
Mathias Nyman, Andy Shevchenko, and Rafael J. Wysocki.
- ACPICA update to version 20121018 from Bob Moore and Lv Zheng.
- ACPI memory hotplug update from Wen Congyang and Yasuaki Ishimatsu.
- Introduction of acpi_handle_<level>() messaging macros and ACPI-based
CPU hot-remove support from Toshi Kani.
- ACPI EC updates from Feng Tang.
- cpufreq updates from Viresh Kumar, Fabio Baltieri and others.
- cpuidle changes to quickly notice governor prediction failure from
Youquan Song.
- Support for using multiple cpuidle drivers at the same time and
cpuidle cleanups from Daniel Lezcano.
- devfreq updates from Nishanth Menon and others.
- cpupower update from Thomas Renninger.
- Fixes and small cleanups all over the place.
* tag 'pm+acpi-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (196 commits)
mmc: sdhci-acpi: enable runtime-pm for device HID INT33C6
ACPI: add Haswell LPSS devices to acpi_platform_device_ids list
ACPI: add documentation about ACPI 5 enumeration
pnpacpi: fix incorrect TEST_ALPHA() test
ACPI / PM: Fix header of acpi_dev_pm_detach() in acpi.h
ACPI / video: ignore BIOS initial backlight value for HP Folio 13-2000
ACPI : do not use Lid and Sleep button for S5 wakeup
ACPI / PNP: Do not crash due to stale pointer use during system resume
ACPI / video: Add "Asus UL30VT" to ACPI video detect blacklist
ACPI: do acpisleep dmi check when CONFIG_ACPI_SLEEP is set
spi / ACPI: add ACPI enumeration support
gpio / ACPI: add ACPI support
PM / devfreq: remove compiler error with module governors (2)
cpupower: IvyBridge (0x3a and 0x3e models) support
cpupower: Provide -c param for cpupower monitor to schedule process on all cores
cpupower tools: Fix warning and a bug with the cpu package count
cpupower tools: Fix malloc of cpu_info structure
cpupower tools: Fix issues with sysfs_topology_read_file
cpupower tools: Fix minor warnings
cpupower tools: Update .gitignore for files created in the debug directories
...
The spi support code works on SPARC too. No reason to exclude it from
the party.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Bill Pemberton has done most of the legwork on this series. I've used
his script to purge the attributes from the drivers/gpio tree.
Reported-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch allows to specify that a SPI device is connected in 3-wire mode via
device tree.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix problem discovered with sparse:
+ drivers/spi/spi.c:1554:37: sparse: incompatible types in comparison expression (different signedness)
drivers/spi/spi.c: In function 'spi_write_then_read':
drivers/spi/spi.c:1554:23: warning: comparison of distinct pointer types lacks a cast [enabled by default]
The change to SPI_BUFSIZ was introduced in commit b3a223ee2, "spi:
Remove SPI_BUFSIZ restriction on spi_write_then_read()"
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In order to avoid constantly allocating and deallocating there is a fixed
buffer which spi_write_then_read() uses for transfers, with an early error
check to ensure that the transfer fits within the buffer. This limits the
size of transfers to this size, currently max(32, SMP_CACHE_BYTES).
Since we can dynamically allocate and in fact already have a fallback
to do so when there is contention for the fixed buffer remove this
restriction and instead dynamically allocate a suitably sized buffer if
the transfer won't fit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
ACPI 5 introduced SPISerialBus resource that allows us to enumerate and
configure the SPI slave devices behind the SPI controller. This patch adds
support for this to the SPI core.
In addition we bind ACPI nodes to SPI devices. This makes it possible for
the slave drivers to get the ACPI handle for further configuration.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently of_register_spi_devices() function registers all SPI devices,
independetly from their status property in device tree. According to
"ePAPR 1.1" spec, device should only be registered if there is no
"status" property, or it has "ok" (or "okay") value (see
of_device_is_available()). In case of "platform devices",
of_platform_device_create_pdata() checks for "status" and ensures
that disabled devices are not pupulated. But such check for SPI buses
was missing until now. Fix it.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@sysgo.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This will allow to use gpio for chip select with no modification in the
driver binding
When use the cs-gpios, the gpio number will be passed via the cs_gpio field
and the number of chip select will automatically increased with max(hw cs, gpio cs).
So if for example the controller has 2 CS lines, and the cs-gpios
property looks like this:
cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>;
Then it should be configured so that num_chipselect = 4 with the
following mapping:
cs0 : &gpio1 0 0
cs1 : native
cs2 : &gpio1 1 0
cs3 : &gpio1 2 0
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: spi-devel-general@lists.sourceforge.net
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
[grant.likely: fixed up type of cs count so min() can do type checking]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently the master->setup() is called unconditionally.
The assumption is that every driver need to implement this
callback. This encourages drivers to populate empty functions
to prevent crashing.
This patch prevents the call of master->setup() if it is not
populated.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When spi client does the spi transfer and does not sets
the bits_per_word for each transfer then set it as default
of spi device in spi core before calling low level transfer.
Removing the similar code from spi-tegra20-slink driver as
it is not required.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Uwe Kleine-König