* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7088/1: entry: fix wrong parameter name used in do_thumb_abort
ARM: 7080/1: l2x0: make sure I&D are not locked down on init
ARM: 7081/1: mach-integrator: fix the clocksource
NET: am79c961: fix race in link status code
ARM: 7067/1: mm: keep significant bits in pfn_valid
Since backlight_types[] isn't modified, let's declare it const. That
was probably the intention of the author of commit bb7ca747f8
("backlight: add backlight type"), via which the "const char const *"
construct was introduced. The duplicate const was detected by sparse.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://neil.brown.name/md:
md: Fix handling for devices from 2TB to 4TB in 0.90 metadata.
md/raid1,10: Remove use-after-free bug in make_request.
md/raid10: unify handling of write completion.
Avoid dereferencing a 'request_queue' after last close.
0.90 metadata uses an unsigned 32bit number to count the number of
kilobytes used from each device.
This should allow up to 4TB per device.
However we multiply this by 2 (to get sectors) before casting to a
larger type, so sizes above 2TB get truncated.
Also we allow rdev->sectors to be larger than 4TB, so it is possible
for the array to be resized larger than the metadata can handle.
So make sure rdev->sectors never exceeds 4TB when 0.90 metadata is in
used.
Also the sanity check at the end of super_90_load should include level
1 as it used ->size too. (RAID0 and Linear don't use ->size at all).
Reported-by: Pim Zandbergen <P.Zandbergen@macroscoop.nl>
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
A single request to RAID1 or RAID10 might result in multiple
requests if there are known bad blocks that need to be avoided.
To detect if we need to submit another write request we test:
if (sectors_handled < (bio->bi_size >> 9)) {
However this is after we call **_write_done() so the 'bio' no longer
belongs to us - the writes could have completed and the bio freed.
So move the **_write_done call until after the test against
bio->bi_size.
This addresses https://bugzilla.kernel.org/show_bug.cgi?id=41862
Reported-by: Bruno Wolff III <bruno@wolff.to>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Signed-off-by: NeilBrown <neilb@suse.de>
A write can complete at two different places:
1/ when the last member-device write completes, through
raid10_end_write_request
2/ in make_request() when we remove the initial bias from ->remaining.
These two should do exactly the same thing and the comment says they
do, but they don't.
So factor the correct code out into a function and call it in both
places. This makes the code much more similar to RAID1.
The difference is only significant if there is an error, and they
usually take a while, so it is unlikely that there will be an error
already when make_request is completing, so this is unlikely to cause
real problems.
Signed-off-by: NeilBrown <neilb@suse.de>
Modifying the Maximum Read Request Size to 0 (value of 128Bytes) has
massive negative ramifications on some devices. Without knowing which
devices have this issue, do not modify from the default value when
walking the PCI-E bus in pcie_bus_safe mode. Also, make pcie_bus_safe
the default procedure.
Tested-by: Sven Schnelle <svens@stackframe.org>
Tested-by: Simon Kirby <sim@hostway.ca>
Tested-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Reported-and-tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-and-tested-by: Niels Ole Salscheider <niels_ole@salscheider-online.de>
References: https://bugzilla.kernel.org/show_bug.cgi?id=42162
Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b03e7495a8 ("PCI: Set PCI-E Max Payload Size on fabric")
introduced a potential NULL pointer dereference in calls to
pcie_bus_configure_settings due to attempts to access pci_bus self
variables when the self pointer is NULL.
To correct this, verify that the self pointer in pci_bus is non-NULL
before dereferencing it.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Shyam Iyer <shyam_iyer@dell.com>
Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://dev.laptop.org/users/cjb/mmc:
mmc: sdhci-s3c: Fix mmc card I/O problem
mmc: sd: UHS-I bus speed should be set last in UHS initialization
mmc: sdhi: initialise mmc_data->flags before use
mmc: core: use non-reentrant workqueue for clock gating
mmc: core: prevent aggressive clock gating racing with ios updates
mmc: rename mmc_host_clk_{ungate|gate} to mmc_host_clk_{hold|release}
mmc: sdhci-esdhc-imx: add missing inclusion of linux/module.h
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine/ste_dma40: fix memory leak due to prepared descriptors
dmaengine/ste_dma40: fix Oops due to double free of client descriptor
dmaengine/ste_dma40: remove duplicate call to d40_pool_lli_free().
dmaengine/ste_dma40: add missing kernel doc for pending_queue
* 'for-linus' of git://twin.jikos.cz/jikos/hid:
HID: wacom: Unregister sysfs attributes on remove
HID: wacom: Fix error path of power-supply initialization
HID: add support for HuiJia USB Gamepad connector
HID: magicmouse: ignore 'ivalid report id' while switching modes, v2
HID: magicmouse: Set resolution of touch surfaces
* 'amd/fixes' of git://git.8bytes.org/scm/iommu:
iommu/amd: Don't take domain->lock recursivly
iommu/amd: Make sure iommu->need_sync contains correct value
* 'timers-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
rtc: twl: Fix registration vs. init order
rtc: Initialized rtc_time->tm_isdst
rtc: Fix RTC PIE frequency limit
rtc: rtc-twl: Remove lockdep related local_irq_enable()
rtc: rtc-twl: Switch to using threaded irq
rtc: ep93xx: Fix 'rtc' may be used uninitialized warning
alarmtimers: Avoid possible denial of service with high freq periodic timers
alarmtimers: Memset itimerspec passed into alarm_timer_get
alarmtimers: Avoid possible null pointer traversal
* branch 'linux-next' of git://git.infradead.org/ubifs-2.6:
UBIFS: not build debug messages with CONFIG_UBIFS_FS_DEBUG disabled
* branch 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: do not link debug messages when debugging is disabled
HID devices can be hotplugged so we should unregister all sysfs attributes when
removing a driver. Otherwise, manually unloading the wacom-driver will not
remove the sysfs attributes. Only when the device is disconnected, they are
removed, eventually.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
power_supply_unregister() must not be called if power_supply_register() failed.
The wdata->psy.dev pointer may point to invalid memory after a failed
power_supply_register() and hence wacom_remove() will fail while calling
power_supply_unregister().
This changes the wacom_probe function to fail if it cannot register the
power_supply devices. If we would want to keep the previous behaviour we had to
keep some flag about the power_supply state and check it on wacom_remove, but
this seems inappropriate here. Hence, we simply fail, too, if
power_supply_register fails.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In tegra_i2c_fill_tx_fifo, once we have finished pushing all the bytes
to the I2C hardware controller, the interrupt might happen before we
have updated i2c_dev->msg_buf_remaining at the end of the function.
Then, in tegra_i2c_isr, we will call again tegra_i2c_fill_tx_fifo
triggering weird behaviour. This has been shown to happen under real
conditions.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch was intended to be part of 7ca2d1a105a239e300b937e9c41a10a4bd08f569
"i2c: Tegra: Add DeviceTree support". However, an early version of that patch,
which was missing a chunk, was applied to next-i2c. This change is that
missing chunk.
Signed-off-by: John Bonesio <bones@secretlab.ca>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Rewrite the loop walking the id array during probe. The new code is
better adapted to a null-terminated array, and is also clearer and
more efficient than the original.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Axel Lin <axel.lin@gmail.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Current calculation is completely wrong. Add missing brackets to fix it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 3.0+
The conversion to per bus type registration functions means we don't need
to do module_get()s to hold the bus types in memory (their users will link
to them) so we removed all those calls. This left module_put() calls in
the cleanup paths which aren't needed and which cause unbalanced puts if
we ever try to unload anything.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Prepared descriptors that are not submitted will not be freed. Add
prepared descriptor to a list to be able to release them upon
dmaengine_terminate_all().
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The client list may exist in two lists at the same time. This makes free
fail since the same desc is freed multiple times. Remove desc from
client list when adding it to the pending queue. Move free of client owned
descriptors from free_dma() to terminate_all().
Unable to handle kernel paging request at virtual address 00100104
pgd = dea8c000
[00100104] *pgd=1ea62831, *pte=00000000, *ppte=00000000
Internal error: Oops: 817 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 Not tainted (3.1.0-rc3+ #58)
PC is at d40_free_chan_resources+0x64/0x330
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The link status code operates from a timer, and writes the index
register without first taking a lock. A well-placed interrupt
between writing the index register and reading the data register
could change the index register on us, which will return wrong data.
Add the necessary lock.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: make sure pci max read request size is valid on evergreen+ (v2)
drm/radeon/kms: set a default max_pixel_clock
The domain_flush_devices() function takes the domain->lock.
But this function is only called from update_domain() which
itself is already called unter the domain->lock. This causes
a deadlock situation when the dma-address-space of a domain
grows larger than 1GB.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The value is only set to true but never set back to false,
which causes to many completion-wait commands to be sent to
hardware. Fix it with this patch.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
If the bios or OS sets the pci max read request size to 0 or an
invalid value (6,7), it can result in a hang or slowdown. Check
and set it to something sane if it's invalid.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=42162
v2: use pci reg defines from include/linux/pci_regs.h
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch fixes the problem in sdhci-s3c host driver for Samsung Soc's.
During the card identification stage the mmc core driver enumerates for
the best bus width in combination with the highest available data rate.
It starts enumerating from the highest bus width (8) to lowest width (1).
In case of few MMC cards the 4-bit bus enumeration fails and tries
the 1-bit bus enumeration. When switched to 1-bit bus mode the host driver
has to clear the previous bus width setting and apply the new setting.
The current patch will clear the previous bus mode and apply the new
mode setting.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_sd_init_uhs_card function sets the driver type, current limit
and bus speed mode on card as well as on host controller side.
Currently bus speed mode is set by sending CMD6 to card and
immediately setting the timing mode in host controller. But
then before initiating tuning sequence, it also tries to set
current limit by sending CMD6 to card which results in data
timeout errors in controller if bus speed mode is SDR50/SDR104 mode.
So basically bus speed mode should be set only after current limit
is set in the card and immediately after setting the bus speed mode,
tuning sequence should be initiated.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This corrects a logic error that I introduced in
"mmc: sdhi: Add write16_hook"
Reported-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
The default multithread workqueue can cause the same work to be executed
concurrently on a different CPUs. This isn't really suitable for clock
gating as it might already gated the clock and gating it twice results both
host->clk_old and host->ios.clock to be set to 0.
To prevent this from happening we use system_nrt_wq instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We have seen at least two different races when clock gating kicks in in a
middle of ios structure update.
First one happens when ios->clock is changed outside of aggressive clock
gating framework, for example via mmc_set_clock(). The race might happen
when we run following code:
mmc_set_ios():
...
if (ios->clock > 0)
mmc_set_ungated(host);
Now if gating kicks in right after the condition check we end up setting
host->clk_gated to false even though we have just gated the clock. Next
time a request is started we try to ungate and restore the clock in
mmc_host_clk_hold(). However since we have host->clk_gated set to false the
original clock is not restored.
This eventually will cause the host controller to hang since its clock is
disabled while we are trying to issue a request. For example on Intel
Medfield platform we see:
[ 13.818610] mmc2: Timeout waiting for hardware interrupt.
[ 13.818698] sdhci: =========== REGISTER DUMP (mmc2)===========
[ 13.818753] sdhci: Sys addr: 0x00000000 | Version: 0x00008901
[ 13.818804] sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000
[ 13.818853] sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
[ 13.818903] sdhci: Present: 0x1fff0000 | Host ctl: 0x00000001
[ 13.818951] sdhci: Power: 0x0000000d | Blk gap: 0x00000000
[ 13.819000] sdhci: Wake-up: 0x00000000 | Clock: 0x00000000
[ 13.819049] sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
[ 13.819098] sdhci: Int enab: 0x00ff00c3 | Sig enab: 0x00ff00c3
[ 13.819147] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
[ 13.819196] sdhci: Caps: 0x6bee32b2 | Caps_1: 0x00000000
[ 13.819245] sdhci: Cmd: 0x00000000 | Max curr: 0x00000000
[ 13.819292] sdhci: Host ctl2: 0x00000000
[ 13.819331] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000
[ 13.819377] sdhci: ===========================================
[ 13.919605] mmc2: Reset 0x2 never completed.
and it never recovers.
Second race might happen while running mmc_power_off():
static void mmc_power_off(struct mmc_host *host)
{
host->ios.clock = 0;
host->ios.vdd = 0;
[ clock gating kicks in here ]
/*
* Reset ocr mask to be the highest possible voltage supported for
* this mmc host. This value will be used at next power up.
*/
host->ocr = 1 << (fls(host->ocr_avail) - 1);
if (!mmc_host_is_spi(host)) {
host->ios.bus_mode = MMC_BUSMODE_OPENDRAIN;
host->ios.chip_select = MMC_CS_DONTCARE;
}
host->ios.power_mode = MMC_POWER_OFF;
host->ios.bus_width = MMC_BUS_WIDTH_1;
host->ios.timing = MMC_TIMING_LEGACY;
mmc_set_ios(host);
}
If the clock gating worker kicks in while we are only partially updated the
ios structure the host controller gets incomplete ios and might not work as
supposed. Again on Intel Medfield platform we get:
[ 4.185349] kernel BUG at drivers/mmc/host/sdhci.c:1155!
[ 4.185422] invalid opcode: 0000 [#1] PREEMPT SMP
[ 4.185509] Modules linked in:
[ 4.185565]
[ 4.185608] Pid: 4, comm: kworker/0:0 Not tainted 3.0.0+ #240 Intel Corporation Medfield/iCDKA
[ 4.185742] EIP: 0060:[<c136364e>] EFLAGS: 00010083 CPU: 0
[ 4.185827] EIP is at sdhci_set_power+0x3e/0xd0
[ 4.185891] EAX: f5ff98e0 EBX: f5ff98e0 ECX: 00000000 EDX: 00000001
[ 4.185970] ESI: f5ff977c EDI: f5ff9904 EBP: f644fe98 ESP: f644fe94
[ 4.186049] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[ 4.186125] Process kworker/0:0 (pid: 4, ti=f644e000 task=f644c0e0 task.ti=f644e000)
[ 4.186219] Stack:
[ 4.186257] f5ff98e0 f644feb0 c1365173 00000282 f5ff9460 f5ff96e0 f5ff96e0 f644feec
[ 4.186418] c1355bd8 f644c0e0 c1499c3d f5ff96e0 f644fed4 00000006 f5ff96e0 00000286
[ 4.186579] f644fedc c107922b f644feec 00000286 f5ff9460 f5ff9700 f644ff10 c135839e
[ 4.186739] Call Trace:
[ 4.186802] [<c1365173>] sdhci_set_ios+0x1c3/0x340
[ 4.186883] [<c1355bd8>] mmc_gate_clock+0x68/0x120
[ 4.186963] [<c1499c3d>] ? _raw_spin_unlock_irqrestore+0x4d/0x60
[ 4.187052] [<c107922b>] ? trace_hardirqs_on+0xb/0x10
[ 4.187134] [<c135839e>] mmc_host_clk_gate_delayed+0xbe/0x130
[ 4.187219] [<c105ec09>] ? process_one_work+0xf9/0x5b0
[ 4.187300] [<c135841d>] mmc_host_clk_gate_work+0xd/0x10
[ 4.187379] [<c105ec82>] process_one_work+0x172/0x5b0
[ 4.187457] [<c105ec09>] ? process_one_work+0xf9/0x5b0
[ 4.187538] [<c1358410>] ? mmc_host_clk_gate_delayed+0x130/0x130
[ 4.187625] [<c105f3c8>] worker_thread+0x118/0x330
[ 4.187700] [<c1496cee>] ? preempt_schedule+0x2e/0x50
[ 4.187779] [<c105f2b0>] ? rescuer_thread+0x1f0/0x1f0
[ 4.187857] [<c1062cf4>] kthread+0x74/0x80
[ 4.187931] [<c1062c80>] ? __init_kthread_worker+0x60/0x60
[ 4.188015] [<c149acfa>] kernel_thread_helper+0x6/0xd
[ 4.188079] Code: 81 fa 00 00 04 00 0f 84 a7 00 00 00 7f 21 81 fa 80 00 00 00 0f 84 92 00 00 00 81 fa 00 00 0
[ 4.188780] EIP: [<c136364e>] sdhci_set_power+0x3e/0xd0 SS:ESP 0068:f644fe94
[ 4.188898] ---[ end trace a7b23eecc71777e4 ]---
This BUG() comes from the fact that ios.power_mode was still in previous
value (MMC_POWER_ON) and ios.vdd was set to zero.
We prevent these by inhibiting the clock gating while we update the ios
structure.
Both problems can be reproduced by simply running the device in a reboot
loop.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
As per suggestion by Linus Walleij:
> If you think the names of the functions are confusing then
> you may rename them, say like this:
>
> mmc_host_clk_ungate() -> mmc_host_clk_hold()
> mmc_host_clk_gate() -> mmc_host_clk_release()
>
> Which would make the usecases more clear
(This is CC'd to stable@ because the next two patches, which fix
observable races, depend on it.)
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'for-linus' of git://neil.brown.name/md:
md/raid5: fix a hang on device failure.
md: fix clearing of 'blocked' flag in the presence of bad blocks.
md/linear: avoid corrupting structure while waiting for rcu_free to complete.
md: use REQ_NOIDLE flag in md_super_write()
md: ensure changes to 'write-mostly' are reflected in metadata.
md: report failure if a 'set faulty' request doesn't.
On some Power rv100 cards, we have no ATY OF table, but we have
no combios table either, and hence we refuse all modes on VGA-0
since we end up with a 0 max pixel clock.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cc: stable@kernel.org
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Waiting for a 'blocked' rdev to become unblocked in the raid5d thread
cannot work with internal metadata as it is the raid5d thread which
will clear the blocked flag.
This wasn't a problem in 3.0 and earlier as we only set the blocked
flag when external metadata was used then.
However we now set it always, so we need to be more careful.
Signed-off-by: NeilBrown <neilb@suse.de>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add s/r quirk for Compaq Presario V5245EU
drm/radeon/kms: evergreen & ni reset SPI block on CP resume
drm: Fix the number of connector and encoder to cleanup functions
For some reason SPI block is in broken state after module
unloading. This lead to broken rendering after reloading
module. Fix this by reseting SPI block in CP resume function
Signed-off-by: Jerome Glisse <jglisse@redhat.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
When the 'blocked' flag on a device is cleared while there are
unacknowledged bad blocks we must fail the device. This is needed for
backwards compatability of the interface.
The code currently uses the wrong test for "unacknowledged bad blocks
exist". Change it to the right test.
Signed-off-by: NeilBrown <neilb@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (42 commits)
netpoll: fix incorrect access to skb data in __netpoll_rx
cassini: init before use in cas_interruptN.
can: ti_hecc: Fix uninitialized spinlock in probe
can: ti_hecc: Fix unintialized variable
net: sh_eth: fix the compile error
net/phy: fix DP83865 phy interrupt handler
sendmmsg/sendmsg: fix unsafe user pointer access
ibmveth: Fix leak when recycling skb and hypervisor returns error
arp: fix rcu lockdep splat in arp_process()
bridge: fix a possible use after free
bridge: Pseudo-header required for the checksum of ICMPv6
mcast: Fix source address selection for multicast listener report
MAINTAINERS: Update GIT trees for network development
ath9k: Fix PS wrappers in ath9k_set_coverage_class
carl9170: Fix mismatch in carl9170_op_set_key mutex lock-unlock
wl12xx: add max_sched_scan_ssids value to the hw description
wl12xx: Fix validation of pm_runtime_get_sync return value
wl12xx: Remove obsolete testmode NVS push command
bcma: add uevent to the bus, to autoload drivers
ath9k_hw: Fix STA (AR9485) bringup issue due to incorrect MAC address
...
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-3.x:
sh: fix the compile error in setup-sh7757.c
serial: sh-sci: report CTS as active for get_mctrl
sh: Add unaligned memory access for PC relative intructions
sh: Fix unaligned memory access for branches without delay slots
sh: Fix up fallout from cpuidle changes.
serial: sh-sci: console Runtime PM support
sh: Fix conflicting definitions of ptrace_triggered
serial: sh-sci: fix DMA build by including dma-mapping.h
serial: sh-sci: Fix up default regtype probing.
sh: intc: enable both edges GPIO interrupts on sh7372
shwdt: fix usage of mod_timer
clocksource: sh_cmt: wait for CMCNT on init V2
Linus Torvalds