Commit Graph

11 Commits

Author SHA1 Message Date
Haavard Skinnemoen b47eb4092f avr32: Clean up HMATRIX code
Introduce a few helper functions for HMATRIX configuration and clean up
the register definitions. Also add definitions for the HMATRIX master
and slave IDs on the AT32AP700x chips.

Also make the definitions in hmatrix.h available to board code by moving
it to <mach/hmatrix.h>

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-08-08 12:44:01 +02:00
Haavard Skinnemoen 02a00cf672 avr32: Power Management support ("standby" and "mem" modes)
Implement Standby support. In this mode, we'll suspend all drivers,
put the SDRAM in self-refresh mode and switch off the HSB bus
("frozen" mode.)

Implement Suspend-to-mem support. In this mode, we suspend all
drivers, put the SDRAM into self-refresh mode and switch off all
internal clocks except the 32 kHz oscillator ("stop" mode.)

The lowest-level suspend code runs from a small portion of SRAM
allocated at startup time. This gets rid of a small potential race
with the SDRAM where we might try to enter self-refresh mode in the
middle of an icache burst. We also relocate all interrupt and
exception handlers to SRAM during the small window when we enter and
exit the low-power modes.

We don't need to do any special tricks to start and stop the PLL. The
main clock is automatically gated by hardware until the PLL is stable.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2008-07-02 11:05:01 +02:00
Haavard Skinnemoen d7ff2a4a28 avr32: Rename at32ap.c -> pdc.c
The only thing left in at32ap.c is some PDC stuff. Rename the file to
reflect what it actually does.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2008-06-28 15:08:48 +02:00
David Brownell e723ff666a avr32: Generic clockevents support
This combines three patches from David Brownell:
  * avr32: tclib support
  * avr32: simplify clocksources
  * avr32: Turn count/compare into a oneshot clockevent device

Register both TC blocks (instead of just the first one) so that
the AT32/AT91 tclib code will pick them up (instead of just the
avr32-only PIT-style clocksource).

Rename the first one and its resources appropriately.

More cleanups to the cycle counter clocksource code

 - Disable all the weak symbol magic; remove the AVR32-only TCB-based
   clocksource code (source and header).

 - Mark the __init code properly.

 - Don't forget to report IRQF_TIMER.

 - Make the system work properly with this clocksource, by preventing
   use of the CPU "idle" sleep state in the idle loop when it's used.

Package the avr32 count/compare timekeeping support as a oneshot
clockevent device, so it supports NO_HZ and high res timers.
This means it also supports plugging in other clockevent devices
and clocksources.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2008-04-19 20:40:08 -04:00
Haavard Skinnemoen 7e59128f31 avr32: Move sleep code into mach-at32ap
Create a new file, pm-at32ap700x.S, in mach-at32ap and move the CPU
idle sleep code there. Make it possible to disable the sleep code.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2008-04-19 20:40:07 -04:00
Haavard Skinnemoen 438ff3f3cc [AVR32] Add support for AT32AP7001 and AT32AP7002
These are derivatives of the AT32AP7000 chip, which means that most of
the code stays the same. Rename a few files, functions, definitions
and config symbols to reflect that they apply to all AP700x chips, and
exclude some platform devices from chips where they aren't present.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2008-01-25 08:31:41 +01:00
Hans-Christian Egtvedt 9e58e1855c [AVR32] CPU frequency scaling for AT32AP
This patch enables CPU frequency scaling for AT32AP devices. This will
enable the CPU to scale between the speed of the high speed bus and
the master clock and thus save some power.

The patch also adds a parent to cpu_clk and a cpu_clk_set_rate to
enable changing the CPU clock divider in a sane way.

The driver does not check if the given rate is 0, thus resulting in a
div by 0.  I think this check should be go into the clk_set_rate
framework, and not here.

Tested on AT32AP7000/ATSTK1000.

Hardware documentation can be found in the AT32AP7000 datasheet.

Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-07-18 20:45:51 +02:00
Hans-Christian Egtvedt 7760989e5e [AVR32] Change system timer from count-compare to Timer/Counter 0
Due to limitation of the count-compare system timer (not able to
count when CPU is in sleep), the system timer had to be changed to
use a peripheral timer/counter.

The old COUNT-COMPARE code is still present in time.c as weak
functions. The new timer is added to the architecture directory.

This patch sets up TC0 as system timer The new timer has been tested
on AT32AP7000/ATSTK1000 at 100 Hz, 250 Hz, 300 Hz and 1000 Hz.

For more details about the timer/counter see the datasheet for
AT32AP700x available at

http://www.atmel.com/dyn/products/product_card.asp?part_id=3903

Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-04-27 13:44:12 +02:00
Haavard Skinnemoen 6a4e5227a3 [AVR32] GPIO API implementation
Arch-neutral GPIO calls for AVR32. GPIO IRQ support written by
David Brownell.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-02-09 15:01:58 +01:00
Haavard Skinnemoen bc157b7596 [PATCH] AVR32 MTD: Static Memory Controller driver
This patchset adds the necessary drivers and infrastructure to access the
external flash on the ATSTK1000 board through the MTD subsystem.  With this
stuff in place, it will be possible to use a jffs2 filesystem stored in the
external flash as a root filesystem.  It might also be possible to update the
boot loader if you drop the write protection of partition 0.

As suggested by David Woodhouse, I reworked the patches to use the physmap
driver instead of introducing a separate mapping driver for the ATSTK1000.
I've also cleaned up the hsmc header by removing useless comments and
converting spaces to tabs (my headerfile generator needs some work.)

Unfortunately, I couldn't unlock the flash in fixup_use_atmel_lock because the
erase regions hadn't been set up yet, so I had to do it from cfi_amdstd_setup
instead.

This patch:

This adds a simple API for configuring the static memory controller along with
an implementation for the Atmel HSMC.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-26 08:48:54 -07:00
Haavard Skinnemoen 5f97f7f940 [PATCH] avr32 architecture
This adds support for the Atmel AVR32 architecture as well as the AT32AP7000
CPU and the AT32STK1000 development board.

AVR32 is a new high-performance 32-bit RISC microprocessor core, designed for
cost-sensitive embedded applications, with particular emphasis on low power
consumption and high code density.  The AVR32 architecture is not binary
compatible with earlier 8-bit AVR architectures.

The AVR32 architecture, including the instruction set, is described by the
AVR32 Architecture Manual, available from

http://www.atmel.com/dyn/resources/prod_documents/doc32000.pdf

The Atmel AT32AP7000 is the first CPU implementing the AVR32 architecture.  It
features a 7-stage pipeline, 16KB instruction and data caches and a full
Memory Management Unit.  It also comes with a large set of integrated
peripherals, many of which are shared with the AT91 ARM-based controllers from
Atmel.

Full data sheet is available from

http://www.atmel.com/dyn/resources/prod_documents/doc32003.pdf

while the CPU core implementation including caches and MMU is documented by
the AVR32 AP Technical Reference, available from

http://www.atmel.com/dyn/resources/prod_documents/doc32001.pdf

Information about the AT32STK1000 development board can be found at

http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3918

including a BSP CD image with an earlier version of this patch, development
tools (binaries and source/patches) and a root filesystem image suitable for
booting from SD card.

Alternatively, there's a preliminary "getting started" guide available at
http://avr32linux.org/twiki/bin/view/Main/GettingStarted which provides links
to the sources and patches you will need in order to set up a cross-compiling
environment for avr32-linux.

This patch, as well as the other patches included with the BSP and the
toolchain patches, is actively supported by Atmel Corporation.

[dmccr@us.ibm.com: Fix more pxx_page macro locations]
[bunk@stusta.de: fix `make defconfig']
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave McCracken <dmccr@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-26 08:48:54 -07:00