Commit Graph

95 Commits

Author SHA1 Message Date
Shawn Guo b5680e0b59 net/fec: add dual fec support for mx28
This patch is to add mx28 dual fec support. Here are some key notes
for mx28 fec controller.

 - The mx28 fec controller naming ENET-MAC is a different IP from FEC
   used on other i.mx variants.  But they are basically compatible
   on software interface, so it's possible to share the same driver.
 - ENET-MAC design on mx28 made an improper assumption that it runs
   on a big-endian system. As the result, driver has to swap every
   frame going to and coming from the controller.
 - The external phys can only be configured by fec0, which means fec1
   can not work independently and both phys need to be configured by
   mii_bus attached on fec0.
 - ENET-MAC reset will get mac address registers reset too.
 - ENET-MAC MII/RMII mode and 10M/100M speed are configured
   differently FEC.
 - ETHER_EN bit must be set to get ENET-MAC interrupt work.

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09 15:42:56 -08:00
Shawn Guo bcc67771ed net/fec: improve pm for better suspend/resume
The following commit made a fix to use fec_enet_open/fec_enet_close
over fec_enet_init/fec_stop for suspend/resume, because fec_enet_init
does not allow to have a working network interface at resume.

  e3fe8558c7
  net/fec: fix pm to survive to suspend/resume

This fix works for i.mx/mxc fec controller, but fails on mx28 fec
which gets a different interrupt logic design. On i.mx fec, interrupt
can be triggered even bit ETHER_EN of ECR register is not set. But
on mx28 fec, ETHER_EN must be set to get interrupt work. Meanwhile,
MII interrupt is mandatory to resume the driver, because MDIO
read/write changed to interrupt mode by commit below.

  97b72e4320
  fec: use interrupt for MDIO completion indication

fec_restart/fec_stop comes out as the solution working for both
cases.

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09 15:42:56 -08:00
Shawn Guo 49da97dcb6 net/fec: add mac field into platform data and consolidate fec_get_mac
Add mac field into fec_platform_data and consolidate function
fec_get_mac to get mac address in following order.

 1) module parameter via kernel command line fec.macaddr=0x00,0x04,...
 2) from flash in case of CONFIG_M5272 or fec_platform_data mac
    field for others, which typically have mac stored in fuse
 3) fec mac address registers set by bootloader

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09 15:42:55 -08:00
Shawn Guo 8649a230e3 net/fec: remove the use of "index" which is legacy
The "index" becomes legacy since fep->pdev->id starts working
to identify the instance.

Moreover, the call of fec_enet_init(ndev, 0) always passes 0
to fep->index. This makes the following code in fec_get_mac buggy.

	/* Adjust MAC if using default MAC address */
	if (iap == fec_mac_default)
		dev->dev_addr[ETH_ALEN-1] = fec_mac_default[ETH_ALEN-1] + fep->index;

It may be the time to remove "index" and use fep->pdev->id instead.

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09 15:42:55 -08:00
Shawn Guo 862f0982ea net/fec: fix MMFR_OP type in fec_enet_mdio_write
FEC_MMFR_OP_WRITE should be used than FEC_MMFR_OP_READ in
a mdio write operation.

It's probably a typo introduced by commit:

e6b043d512
netdev/fec.c: add phylib supporting to enable carrier detection (v2)

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09 15:42:54 -08:00
Greg Ungerer 6fcc040f02 net: allow FEC driver to use fixed PHY support
At least one board using the FEC driver does not have a conventional
PHY attached to it, it is directly connected to a somewhat simple
ethernet switch (the board is the SnapGear/LITE, and the attached
4-port ethernet switch is a RealTek RTL8305). This switch does not
present the usual register interface of a PHY, it presents nothing.
So a PHY scan will find nothing - it finds ID's of 0 for each PHY
on the attached MII bus.

After the FEC driver was changed to use phylib for supporting PHYs
it no longer works on this particular board/switch setup.

Add code support to use a fixed phy if no PHY is found on the MII bus.
This is based on the way the cpmac.c driver solved this same problem.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-13 09:56:31 -07:00
Oskar Schirmer 03c698c93f net/fec: carrier off initially to avoid root mount failure
with hardware slow in negotiation, the system did freeze
while trying to mount root on nfs at boot time.

the link state has not been initialised so network stack
tried to start transmission right away. this caused instant
retries, as the driver solely stated business upon link down,
rendering the system unusable.

notify carrier off initially to prevent transmission until
phylib will report link up.

Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-10 21:12:27 -07:00
Wolfram Sang 4bee1f9ac0 net/fec: restore interrupt mask after software-reset in fec_stop()
After the change from mdio polling to irq, it became necessary to
restore the interrupt mask after resetting the chip in fec_stop().
Otherwise, with all irqs disabled, no communication with the PHY will be
possible after e.g. un-/replugging the cable and the device gets
stalled.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-22 14:14:46 -07:00
Richard Cochran 28b041139e net: preserve ifreq parameter when calling generic phy_mii_ioctl().
The phy_mii_ioctl() function unnecessarily throws away the original ifreq.
We need access to the ifreq in order to support PHYs that can perform
hardware time stamping.

Two maverick drivers filter the ioctl commands passed to phy_mii_ioctl().
This is unnecessary since phylib will check the command in any case.

Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-18 19:15:25 -07:00
Baruch Siach 97b72e4320 fec: use interrupt for MDIO completion indication
With the move to phylib (commit e6b043d) I was seeing sporadic "MDIO write
timeout" messages. Measure of the actual time spent showed latency times of
more than 1600us.

This patch uses the MII event indication of the FEC hardware to detect
completion of MDIO transactions.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-12 20:21:48 -07:00
Eric Benard 87cad5c385 net/fec: clean suspend/resume
Commit 59d4289b83 converted fec to dev_pm_ops but
didn't update the suspend/resume functions thus leading to the following warning :
"initialization from incompatible pointer type" when CONFIG_PM is set.

This patch also fixe a few indentation and style around CONFIG_PM area.

Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: netdev@vger.kernel.org
Cc: davem@davemloft.net
Cc: amit.kucheria@canonical.com
Cc: s.hauer@pengutronix.de
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-25 21:33:14 -07:00
David S. Miller eedc765ca4 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/sfc/net_driver.h
	drivers/net/sfc/siena.c
2010-06-06 17:42:02 -07:00
Denis Kirjanov 59d4289b83 fec: convert legacy PM hooks to dem_pm_ops
This patch compile tested only.

Convert legacy PM hooks to dev_pm_ops
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-05 02:23:18 -07:00
Denis Kirjanov 1273d97674 fec: Cleanup PHY probing
Cleanup PHY probing: use helpers from phylib

Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-03 03:18:21 -07:00
Denis Kirjanov c7621cb3d9 fec: convert TX hook to netdev_tx_t
Convert TX hook return value to netdev_tx_t

Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-03 03:18:21 -07:00
Eric Bénard e3fe8558c7 net/fec: fix pm to survive to suspend/resume
* in the actual driver, calling fec_stop and fec_enet_init doesn't
allow to have a working network interface at resume (where a
ifconfig down and up is required to recover the interface)
* by using fec_enet_close and fec_enet_open, this patch solves this
problem and handle the case where the link changed between suspend
and resume
* this patch also disable clock at suspend and reenable it at resume

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 06:13:34 -07:00
Bryan Wu 418bd0d4df netdev/fec: fix ifconfig eth0 down hang issue
BugLink: http://bugs.launchpad.net/bugs/559065

In fec open/close function, we need to use phy_connect and phy_disconnect
operation before we start/stop phy. Otherwise it will cause system hang.

Only call fec_enet_mii_probe() in open function, because the first open
action will cause NULL pointer error.

Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-28 03:40:39 -07:00
Baruch Siach 5eb32bd059 fec: add support for PHY interface platform data
The i.MX25 PDK uses RMII to communicate with its PHY. This patch adds
the ability to configure RMII, based on platform data.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by:  Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-24 00:36:13 -07:00
David S. Miller 278554bd65 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	Documentation/feature-removal-schedule.txt
	drivers/net/wireless/ath/ar9170/usb.c
	drivers/scsi/iscsi_tcp.c
	net/ipv4/ipmr.c
2010-05-12 00:05:35 -07:00
Eric Dumazet 1ae5dc342a net: trans_start cleanups
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.

Exceptions are NETIF_F_LLTX drivers

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-10 05:01:31 -07:00
Mattias Walström 7cff0943a1 FEC: Fix kernel panic in fec_set_mac_address.
Fix memory corruption that sometimes result in kernel panic.

Signed-off-by: Mattias Walström <mattias@vmlinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-05 00:55:48 -07:00
Jiri Pirko 22bedad3ce net: convert multicast list to list_head
Converts the list and the core manipulating with it to be the same as uc_list.

+uses two functions for adding/removing mc address (normal and "global"
 variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
 manipulation with lists on a sandbox (used in bonding and 80211 drivers)

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-03 14:22:15 -07:00
Bryan Wu e6b043d512 netdev/fec.c: add phylib supporting to enable carrier detection (v2)
BugLink: http://bugs.launchpad.net/bugs/457878

v2:
 - remove duplicated phy_speed caculation
 - fix the phy_speed caculation according to the DataSheet

v1:
 - removed old MII phy control code
 - add phylib supporting
 - add ethtool interface to make user space NetworkManager works

Tested on Freescale i.MX51 Babbage board.

This patch is based on a patch from Frederic Rodo <fred.rodo@gmail.com>

Cc: Frederic Rodo <fred.rodo@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Acked-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-01 19:53:13 -07:00
Jiri Pirko 48e2f183cb net: convert multiple drivers to use netdev_for_each_mc_addr, part4
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-22 15:45:52 -08:00
Jiri Pirko 4cd24eaf0c net: use netdev_mc_count and netdev_mc_empty when appropriate
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.

Jirka

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-12 11:38:58 -08:00
Amit Kucheria fceb291919 fec: Add LAN8700 phy support
The i.MX51 babbage board has a FEC ethernet controller with this phy.

In the long term we should resurrect the phylib patches for fec.

Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-10 13:05:42 -08:00
Rob Herring 633e7533ce fec: fix uninitialized rx buffer usage
The fec driver was enabling receive buffer descriptor without allocating
the buffers. Make sure the buffer descriptors are initialized to not
start receiving packets.

Open also calls fec_restart after the rx buffers are allocated. With the code
in fec_restart, it zeroes out the buffer descriptors that have just been
setup.

Signed-off-by: Rob Herring <r.herring@freescale.com>
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-10 13:05:42 -08:00
Steven King 78abcb13dd net: fix section mismatch in fec.c
fec_enet_init is called by both fec_probe and fec_resume, so it
shouldn't be marked as __init.

Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-20 18:51:37 -07:00
Linus Torvalds 66bc4a6f34 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (53 commits)
  m68knommu: Make PAGE_SIZE available to assembly files.
  m68knommu: fix ColdFire definition of CLOCK_TICK_RATE
  m68knommu: set multi-function pins for ethernet when enabled
  m68knommu: remove special interrupt handling code for ne2k support
  m68knommu: relax IO_SPACE_LIMIT setting
  m68knommu: remove ColdFire direct interrupt register access
  m68knommu: create a speciailized ColdFire 5272 interrupt controller
  m68knommu: add support for second interrupt controller of ColdFire 5249
  m68knommu: clean up old ColdFire timer irq setup
  m68knommu: map ColdFire interrupts to correct masking bits
  m68knommu: clean up ColdFire 532x CPU timer setup
  m68knommu: simplify ColdFire "timers" clock initialization
  m68knommu: support code to mask external interrupts on old ColdFire CPU's
  m68knommu: merge old ColdFire interrupt controller masking macros
  m68knommu: remove duplicate ColdFire mcf_autovector() code
  m68knommu: move ColdFire INTC definitions to new include file
  m68knommu: mask off all interrupts in ColdFire intc-simr controller
  m68knommu: remove timer device interrupt setup for ColdFire 532x
  m68knommu: remove interrupt masking from ColdFire pit timer
  m68knommu: remove unecessary interrupt level setting in ColdFire 520x setup
  ...
2009-09-17 09:52:43 -07:00
Greg Ungerer 49802967cb m68knommu: remove ColdFire direct interrupt register access
Now that the ColdFire 5272 has full interrupt controller functionality
we can remove all the interrupt masking and acking code from the FEC
ethernet driver.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2009-09-16 09:43:54 +10:00
Uwe Kleine-König 81538e74ca fec: don't enable irqs in hard irq context
fec_enet_mii, fec_enet_rx and fec_enet_tx are both only called by
fec_enet_interrupt in interrupt context.  So they must not use
spin_lock_irq/spin_unlock_irq.

This fixes:
	WARNING: at kernel/lockdep.c:2140 trace_hardirqs_on_caller+0x130/0x194()
	...

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Matt Waddel <Matt.Waddel@freescale.com>
Cc: netdev@vger.kernel.org
Cc: Tim Sander <tim01@vlsi.informatik.tu-darmstadt.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02 23:46:06 -07:00
Uwe Kleine-König 84177a2079 fec: fix recursive locking of mii_lock
mii_discover_phy is only called by fec_enet_mii (via mip->mii_func).  So
&fep->mii_lock is already held and mii_discover_phy must not call
mii_queue which locks &fep->mii_lock, too.

This was noticed by lockdep:

	=============================================
	[ INFO: possible recursive locking detected ]
	2.6.31-rc8-00038-g37d0892 #109
	---------------------------------------------
	swapper/1 is trying to acquire lock:
	 (&fep->mii_lock){-.....}, at: [<c01569f8>] mii_queue+0x2c/0xcc

	but task is already holding lock:
	 (&fep->mii_lock){-.....}, at: [<c0156328>] fec_enet_interrupt+0x78/0x460

	other info that might help us debug this:
	2 locks held by swapper/1:
	 #0:  (rtnl_mutex){+.+.+.}, at: [<c0183534>] rtnl_lock+0x18/0x20
	 #1:  (&fep->mii_lock){-.....}, at: [<c0156328>] fec_enet_interrupt+0x78/0x460

	stack backtrace:
	Backtrace:
	[<c00226fc>] (dump_backtrace+0x0/0x108) from [<c01eac14>] (dump_stack+0x18/0x1c)
	 r6:c781d118 r5:c03e41d8 r4:00000001
	[<c01eabfc>] (dump_stack+0x0/0x1c) from [<c005bae4>] (__lock_acquire+0x1a20/0x1a88)
	[<c005a0c4>] (__lock_acquire+0x0/0x1a88) from [<c005bbac>] (lock_acquire+0x60/0x74)
	[<c005bb4c>] (lock_acquire+0x0/0x74) from [<c01edda8>] (_spin_lock_irqsave+0x54/0x68)
	 r7:60000093 r6:c01569f8 r5:c785e468 r4:00000000
	[<c01edd54>] (_spin_lock_irqsave+0x0/0x68) from [<c01569f8>] (mii_queue+0x2c/0xcc)
	 r7:c785e468 r6:c0156b24 r5:600a0000 r4:c785e000
	[<c01569cc>] (mii_queue+0x0/0xcc) from [<c0156b78>] (mii_discover_phy+0x54/0xa8)
	 r8:00000002 r7:00000032 r6:c785e000 r5:c785e360 r4:c785e000
	[<c0156b24>] (mii_discover_phy+0x0/0xa8) from [<c0156354>] (fec_enet_interrupt+0xa4/0x460)
	 r5:c785e360 r4:c077a170
	[<c01562b0>] (fec_enet_interrupt+0x0/0x460) from [<c0066674>] (handle_IRQ_event+0x48/0x120)
	[<c006662c>] (handle_IRQ_event+0x0/0x120) from [<c0068438>] (handle_level_irq+0x94/0x11c)
	...

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Matt Waddel <Matt.Waddel@freescale.com>
Cc: netdev@vger.kernel.org
Cc: Tim Sander <tim01@vlsi.informatik.tu-darmstadt.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02 23:46:03 -07:00
David S. Miller aa11d958d1 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	arch/microblaze/include/asm/socket.h
2009-08-12 17:44:53 -07:00
Greg Ungerer 9555b31e8c fec: fix FEC driver packet transmission breakage
Commit f0b3fbeae1 ("FEC Buffer rework")
breaks transmission of packets where the skb data buffer is not memory
aligned according to FEC_ALIGNMENT. It incorrectly passes to
dma_sync_single() the buffer address directly from the skb, instead of
the address calculated for use (which may be the skb address or one of
the bounce buffers).

It seems there is no use converting the cpu address of the buffer to
a physical either, since dma_map_single() expects the cpu address and
will return the dma address to use in the descriptor. So remove the use
of __pa() on the buffer address as well.

This patch is against 2.6.30-rc5. This breakage is a regression over
2.6.30, which does not have this problem.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-09 21:45:33 -07:00
David S. Miller da8120355e Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/wireless/orinoco/main.c
2009-07-16 20:21:24 -07:00
Ben Hutchings 635ecaa70e netdev: restore MTU change operation
alloc_etherdev() used to install a default implementation of this
operation, but it must now be explicitly installed in struct
net_device_ops.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-12 14:20:04 -07:00
Patrick McHardy 6ed106549d net: use NETDEV_TX_OK instead of 0 in ndo_start_xmit() functions
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.

Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05 19:16:04 -07:00
Patrick McHardy 5b54814022 net: use symbolic values for ndo_start_xmit() return codes
Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively.

0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases
where its in direct proximity to one of the other values.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-13 01:18:50 -07:00
David S. Miller a54bfa40fd Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 2009-04-16 17:35:26 -07:00
Sascha Hauer fe957c40ec fec: call fec_restart() in fec_open()
We called fec_stop() in fec_enet_close(), thus we have to call
fec_restart() in fec_enet_open().

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-16 02:34:54 -07:00
Sascha Hauer f0b3fbeae1 FEC Buffer rework
Allocate buffers in fec_open and free them again in fec_close. This makes
it possible to use this driver as a module.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-16 02:34:53 -07:00
Sascha Hauer 009fda83ee fec: switch to net_device_ops
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-16 02:34:52 -07:00
Sascha Hauer 3644ee00c4 fec: remove debugging printks
These printks in fec_timeout do not give useful information in
a production kernel.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-16 02:34:52 -07:00
Sascha Hauer 8549889c33 fec: align receive packets
Otherwise we get a lot of alignment errors

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-16 02:34:51 -07:00
Sascha Hauer 4f1ceb4b46 fec: refactor init function
fec_enet_init() does the hardware initialisation and then calls
fec_restart() which does the same initialisation again, so we
can safely remove the initialisation from fec_enet_init().

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-16 02:34:51 -07:00
Sascha Hauer 4e8318368a fec: refactor set_multicast_list() to make it more readable
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-16 02:34:50 -07:00
Sascha Hauer 22f6b860da fec: Codingstyle cleanups
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-16 02:34:50 -07:00
Sascha Hauer 8d4dd5cff8 fec: remove unnecessary cast
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-16 02:34:49 -07:00
Sascha Hauer 2e28532f7e fec: do not typedef struct types
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-16 02:34:48 -07:00
Sascha Hauer f44d630528 fec: switch to writel/readl
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-16 02:34:47 -07:00