http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3978
Section data_l1_cacheline_aligned should be defined in
link script of kernel, when L1 data sram bank A is not available.
In bf536 with all data cache is enabled, there is no L1 data sram.
Current link script won't define section data_l1.cacheline_aligned in
this case. But, if user select put cacheline_aligned data into l1 sram
in kernel menuconfig, these data will be dropped and access to these
data will trigger data CPLB exception.
Do panic in l1 relocation code as well.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Since
r3658 | vapier | 2007-09-12 16:26:11 +0200 (Wed, 12 Sep 2007) | 1 line
add more common defines for output sections
we've had a new line, NOTES, in our linker script, which causes upstream
binutils to complain about "missing phdr". Currently the only other arch
that uses NOTES is i386, and the patch which added it also added
PHDRS {
text PT_LOAD FLAGS(5); /* R_E */
data PT_LOAD FLAGS(7); /* RWE */
note PT_NOTE FLAGS(0); /* ___ */
}
and a few other modifications to use ":text" and ":data" to the linker
script.
It seems that we don't need NOTES at all, so just remove it.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Move the init sections to the end of memory so that after they
are free, run time memory is all continugous - this should help decrease
memory fragementation.
When doing this, we also pack some of the other sections a little closer
together, to make sure we don't waste memory. To make this happen,
we need to rename the .data.init_task section to .init_task.data, so
it doesn't get picked up by the linker script glob.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
This patch consolidate all definitions of .init.text, .init.data
and .exit.text, .exit.data section definitions in
the generic vmlinux.lds.h.
This is a preparational patch - alone it does not buy
us much good.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Break up our .init into separate section like all other ports do and
so that we dont mix text and data (causes disassembly headaches as
pointed out by Robin)
Cc: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
switch to using proper defines this time (THREAD_SIZE and PAGE_SIZE)
instead of just PAGE_SIZE everywhere
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
- we can start taking advantages of defines in asm-generic/vmlinux.lds.h
- move our L1 relocated sections into init so it gets freed after relocation
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
This adds support for the Analog Devices Blackfin processor architecture, and
currently supports the BF533, BF532, BF531, BF537, BF536, BF534, and BF561
(Dual Core) devices, with a variety of development platforms including those
avaliable from Analog Devices (BF533-EZKit, BF533-STAMP, BF537-STAMP,
BF561-EZKIT), and Bluetechnix! Tinyboards.
The Blackfin architecture was jointly developed by Intel and Analog Devices
Inc. (ADI) as the Micro Signal Architecture (MSA) core and introduced it in
December of 2000. Since then ADI has put this core into its Blackfin
processor family of devices. The Blackfin core has the advantages of a clean,
orthogonal,RISC-like microprocessor instruction set. It combines a dual-MAC
(Multiply/Accumulate), state-of-the-art signal processing engine and
single-instruction, multiple-data (SIMD) multimedia capabilities into a single
instruction-set architecture.
The Blackfin architecture, including the instruction set, is described by the
ADSP-BF53x/BF56x Blackfin Processor Programming Reference
http://blackfin.uclinux.org/gf/download/frsrelease/29/2549/Blackfin_PRM.pdf
The Blackfin processor is already supported by major releases of gcc, and
there are binary and source rpms/tarballs for many architectures at:
http://blackfin.uclinux.org/gf/project/toolchain/frs There is complete
documentation, including "getting started" guides available at:
http://docs.blackfin.uclinux.org/ which provides links to the sources and
patches you will need in order to set up a cross-compiling environment for
bfin-linux-uclibc
This patch, as well as the other patches (toolchain, distribution,
uClibc) are actively supported by Analog Devices Inc, at:
http://blackfin.uclinux.org/
We have tested this on LTP, and our test plan (including pass/fails) can
be found at:
http://docs.blackfin.uclinux.org/doku.php?id=testing_the_linux_kernel
[m.kozlowski@tuxland.pl: balance parenthesis in blackfin header files]
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Aubrey Li <aubrey.li@analog.com>
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sonic Zhang