Permission is now granted to the subsystem to format write R0 with:
* an ID = CCHHR, where CC = physical cylinder number,
HH = physical head number, and R = 0
* a key length of zero
* a data length of eight
* a data field containing all zeros
Signed-off-by: Jean-Baptiste Joret <joret@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
All of the ioctls are compatible. Just enable them.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In dasd_device_set_timer and dasd_block_set_timer we interpret the
return value of mod_timer in a wrong way. If the timer expires in
the small window between our check of timer_pending and the call to
mod_timer, then the timer will be set, mod_timer returns zero and
we will call add_timer for a timer that is already pending.
As del_timer and mod_timer do all the necessary checking themselves,
we can simplify our code and remove the race a the same time.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When the connection between host and storage server is lost, the
dasd device driver usually blocks all I/O on affected devices and
waits for them to reappear. In some setups however it would be
better if the I/O is returned as error so that device can be
recovered by some other means, eg. in a raid or multipath setup.
Signed-off-by: Holger Smolinski <Holger.Smolinski@de.ibm.com>
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When a DASD device enters or leaves the 'online' state we need to
trigger change events for the respective disk and partitions.
These extra events are needed because when disk and partitions are
first added, udev rules that try to read disk labels or other data
may fail as the disk may not yet be ready.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When I review ocfs2 code, find there are 2 typos to "successfull". After
doing grep "successfull " in kernel tree, 22 typos found totally -- great
minds always think alike :)
This patch fixes all the similar typos. Thanks for Randy's ack and comments.
Signed-off-by: Coly Li <coyli@suse.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
__dasd_cleanup_cqr should be called with request_queue_lock held and
__dasd_block_process_erp with queue_lock
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
SIM sense data are always 32 bit sense data so sense byte 27 bit 0
has not to be set.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For a large number of I/O requests the values were shifted binary.
The shift was not transparent for the user because the shift value
was not displayed. To make this interface more human readable the
values are shifted decimal and the scale factor is displayed.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The logging of sense data for fatal errors was accidentally removed
during Hyper PAV implementation.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* get rid of fake struct file/struct dentry in __blkdev_get()
* merge __blkdev_get() and do_open()
* get rid of flags argument of blkdev_get()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
To keep the size of changesets sane we split the switch by drivers;
to keep the damn thing bisectable we do the following:
1) rename the affected methods, add ones with correct
prototypes, make (few) callers handle both. That's this changeset.
2) for each driver convert to new methods. *ALL* drivers
are converted in this series.
3) kill the old (renamed) methods.
Note that it _is_ a flagday; all in-tree drivers are converted and by the
end of this series no trace of old methods remain. The only reason why
we do that this way is to keep the damn thing bisectable and allow per-driver
debugging if anything goes wrong.
New methods:
open(bdev, mode)
release(disk, mode)
ioctl(bdev, mode, cmd, arg) /* Called without BKL */
compat_ioctl(bdev, mode, cmd, arg)
locked_ioctl(bdev, mode, cmd, arg) /* Called with BKL, legacy */
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Multipath is best at handling transport errors. If it gets a device
error then there is not much the multipath layer can do. It will just
access the same device but from a different path.
This patch breaks up failfast into device, transport and driver errors.
The multipath layers (md and dm mutlipath) only ask the lower levels to
fast fail transport errors. The user of failfast, read ahead, will ask
to fast fail on all errors.
Note that blk_noretry_request will return true if any failfast bit
is set. This allows drivers that do not support the multipath failfast
bits to continue to fail on any failfast error like before. Drivers
like scsi that are able to fail fast specific errors can check
for the specific fail fast type. In the next patch I will convert
scsi.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
EMC Symmetrix Subsystem Control I/O through CKD dasd requires a
specific parameter list sent to the array via a Perform Subsystem
Function CCW. The Symmetrix response is retrieved from the array
via a Read Subsystem Data CCW.
Signed-off-by: Nigel Hislop <hislop_nigel@emc.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The xpram driver uses a single block device queue for all of its
devices so far. With recent kernels removing xpram module fails to
clean up all sysfs files. The next time the xpram module is loaded
you'll get warnings:
WARNING: at fs/sysfs/dir.c:463 sysfs_add_one+0x5e/0x64()
sysfs: duplicate filename '35:0' can not be created
Modules linked in: xpram(+) [last unloaded: xpram]
Followed by the usual WARN_ON output, followed by an error message
from kobject_add_internal, followed by a badness in genhd. Allocating
a block queue per device fixes this.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In the unsolicited interupt handler fake IRBs from CIO have to be
ignored because there is nothing to do.
The function dump_sense should not be called if there is no sense
data available.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The DCSS block device driver is modified to add >2G DCSSs support and
allow a DCSS block device to map to a set of contiguous DCSSs. The
extmem code is also modified to use new Diagnose x'64' subcodes for
>2G DCSSs.
Signed-off-by: Hongjie Yang <hongjie@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert most s390 users setting bus_id to dev_set_name().
css and ccw busses are deferred since they need some special
treatment.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* Implement disk_devt() and part_devt() and use them to directly
access devt instead of computing it from ->major and ->first_minor.
Note that all references to ->major and ->first_minor outside of
block layer is used to determine devt of the disk (the part0) and as
->major and ->first_minor will continue to represent devt for the
disk, converting these users aren't strictly necessary. However,
convert them for consistency.
* Implement disk_max_parts() to avoid directly deferencing
genhd->minors.
* Update bdget_disk() such that it doesn't assume consecutive minor
space.
* Move devt computation from register_disk() to add_disk() and make it
the only one (all other usages use the initially determined value).
These changes clean up the code and will help disk->part dereference
fix and extended block device numbers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix this compile bug:
CC drivers/s390/block/dcssblk.o
drivers/s390/block/dcssblk.c: In function 'dcssblk_add_store':
drivers/s390/block/dcssblk.c:387: error: implicit declaration of function 'dcssblk_get_segment_by_name'
drivers/s390/block/dcssblk.c:389: error: label 'release_gd' used but not defined
make[1]: *** [drivers/s390/block/dcssblk.o] Error 1
make: *** [drivers/s390/block/] Error 2
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Concurrently adding the same segment may lead to duplicate device_register()
calls, which will trigger an error in kobject code:
"... don't try to register things with the same name in the same directory".
This patch adds a check to avoid this.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Calling a ccw driver's notify function without the ccw device lock
held opens up a race window between discovery and handling of a change
in the device operational state. As a result, the device driver may
encounter unexpected device malfunction, leading to out-of-retry
situations or similar.
Remove race by extending the ccw device lock from state change
discovery to the calling of the notify function.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The Perform Subsystem Function/Prepare for Read Subsystem Data
command requires 12 bytes of parameter data, but the respective data
structure dasd_psf_prssd_data has a length of 16 bytes.
Current storage servers ignore the obsolete bytes, but older models
fail to execute the command and report an incorrect length error.
This causes the device initilization for these devices to fail.
To fix this problem we need to correct the dasd_psf_prssd_data
structure and shorten it to the correct length.
Reported-by: Ivan Warren <ivan@vmfacility.fr>
Reviewed-by: Ivan Warren <ivan@vmfacility.fr>
Tested-by: Ivan Warren <ivan@vmfacility.fr>
CC: stable <stable@kernel.org>
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
In case of error, functions dasd_kmalloc_request and idal_buffer_alloc
return an ERR pointer, but never return the NULL pointer. So after a
call to one of these functions, a NULL test should be replaced by an
IS_ERR test.
A simplified version of the semantic patch that makes this change is
as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@correct_null_test@
expression x,E;
statement S1, S2;
@@
x =
(
dasd_kmalloc_request(...)
|
idal_buffer_alloc(...)
)
<... when != x = E
if (
(
- x@p2 != NULL
+ ! IS_ERR ( x )
|
- x@p2 == NULL
+ IS_ERR( x )
)
)
S1
else S2
...>
? x = E;
// </smpl>
Signed-off-by: Julien Brunel <brunel@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When z/VM provides two virtual devices (minidisks) that reside on the
same real device, both will receive the configuration data from the
real device and thus get the same uid. To fix this problem, z/VM
provides an additional configuration data record that allows to
distinguish between minidisks.
z/VM APAR VM64273 needs be installed so this fix has an effect.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
return value -ENOTSUPP is not valid in userspace context, use
-EOPNOTSUPP instead
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Add missing schedule_bh and check that there is 32 bit sense data.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Extend the scsw data structure to the format required by fcx. Also
provide helper functions for easier access to fields which are present
in both the traditional as well as the modified format.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Use a generic wait_queue to prevent the wait_queue in dasd_sleep_on_
functions from being referenced by callback_data while it does not
exist any more.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When the dasd_int_handler is called with an error code instead of
an irb, the associated request should be restarted. This handling
was missing from the -ETIMEDOUT case. In fact it should be done in
any case.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We should use 'const char *' in the busid functions since the
strings are not modified anyway.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use proc_create() to make sure that ->proc_fops be setup before gluing PDE to
main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove proc_root export. Creation and removal works well if parent PDE is
supplied as NULL -- it worked always that way.
So, one useless export removed and consistency added, some drivers created
PDEs with &proc_root as parent but removed them as NULL and so on.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alter the block device ->direct_access() API to work with the new
get_xip_mem() API (that requires both kaddr and pfn are returned).
Some architectures will not do the right thing in their virt_to_page() for use
by XIP (to translate from the kernel virtual address returned by
direct_access(), to a user mappable pfn in XIP's page fault handler.
However, we can't switch it to just return the pfn and not the kaddr, because
we have no good way to get a kva from a pfn, and XIP requires the kva for its
read(2) and write(2) handlers. So we have to return both.
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux-mm@kvack.org
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the function that prints the segment warning messages found in the
monreader driver and the dcssblk driver to the extmem base code.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Most noteable part of this commit is the new local header file entry.h
which contains all the function declarations of functions that get only
called from asm code or are arch internal. That way we can avoid extern
declarations in C files.
This is more or less the same that was done for sparc64.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Now the system reports system information messages (SIM) to the user.
The System Reference Code (SRC) which is reported to the user gives
the abbility to lookup the reason of the SIM online in the
documentation of the storage server.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
allocating dasd_fba_private without GFP_DMA results in IO error
during read device characteristics of a FBA disk
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
I compiled the kernel without deadline, and the dasd code exits the old
scheduler (CFQ), fails to load the new one (deadline), and then things just
hang - with one of these (sorry about the weird chars - I copy & pasted it
from a 3270 console):
dasd(eckd): 0.0.0151: 3390/0A(CU:3990/01) Cyl:3338 Head:15 Sec:224
------------ cut here ------------
Badness at kernel/mutex.c:134
Modules linked in: dasd_eckd_mod dasd_mod
CPU: 0 Not tainted 2.6.25-rc3 #9
Process exe (pid: 538, task: 000000000d172000, ksp: 000000000d21ef88)
Krnl PSW : 0404000180000000 000000000022fb5c (mutex_lock_nested+0x2a4/0x2cc)
R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:0 CC:0 PM:0 EA:3
Krnl GPRS: 0000000000024218 000000000076fc78 0000000000000000 000000000000000f
000000000022f92e 0000000000449898 000000000f921c00 000003e000162590
00000000001539c4 000000000d172000 070000007fffffff 000000000d21f400
000000000f8f2560 00000000002413f8 000000000022fb44 000000000d21f400
Krnl Code: 000000000022fb50: bf2f1000 icm %r2,15,0(%r1)
000000000022fb54: a774fef6 brc 7,22f940
000000000022fb58: a7f40001 brc 15,22fb5a
>000000000022fb5c: a7f4fef2 brc 15,22f940
000000000022fb60: c0e5fffa112a brasl %r14,171db4
000000000022fb66: 1222 ltr %r2,%r2
000000000022fb68: a784fedb brc 8,22f91e
000000000022fb6c: c010002a0086 larl %r1,76fc78
Call Trace:
(<000000000022f92e> mutex_lock_nested+0x76/0x2cc)
<00000000001539c4> elevator_exit+0x38/0x80
<0000000000156ffe> blk_cleanup_queue+0x62/0x7c
<000003e0001d5414> dasd_change_state+0xe0/0x8ec
<000003e0001d5cae> dasd_set_target_state+0x8e/0x9c
<000003e0001d5f74> dasd_generic_set_online+0x160/0x284
<000003e00011e83a> dasd_eckd_set_online+0x2e/0x40
<0000000000199bf4> ccw_device_set_online+0x170/0x2c0
<0000000000199d9e> online_store_recog_and_online+0x5a/0x14c
<000000000019a08a> online_store+0xbe/0x2ec
<000000000018456c> dev_attr_store+0x38/0x58
<000000000010efbc> sysfs_write_file+0x130/0x190
<00000000000af582> vfs_write+0xb2/0x160
<00000000000afc7c> sys_write+0x54/0x9c
<0000000000025e16> sys32_write+0x2e/0x50
<0000000000024218> sysc_noemu+0x10/0x16
<0000000077e82bd2> 0x77e82bd2
Set elevator pointer to NULL in order to avoid double elevator_exit
calls when elevator_init call for deadline iosched fails.
Also make sure the dasd device driver depends on IOSCHED_DEADLINE so
the default IO scheduler of the dasd driver is present.
Signed-off-by: Josef 'Jeff' Sipek <jeffpc@josefsipek.net>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Using the /proc/dasd/devices interface leaves the reference counter
of alias devices in an inconsistent state. A process that tries to set
such a device offline afterwards will hang.
The dasd_devices_show function returns immediately for alias devices
and this code path was missing a dasd_put_device call.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When a request fails that was started on an alias device then the
first recovery step is to retry it on the base device. If the
recovery request fails again with the same symptoms, the next step
should not be a simple retry, but should be a proper recovery based
on sense data, etc. To do so, the dasd recovery functions need to
recognize the alias recovery step in the erp chain by comparing
the start devices.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After setting the status of the cqr and releasing the lock for the
block cqr queue, we call the cqr callback function, which will usually
just trigger the dasd_block_tasklet. But when the tasklet is already
running the cqr might be processed before we invoke the callback
function. In rare cases the callback pointer may already be invalid
by the time we want to call it, which will result in a panic.
Solution: Call the callback function first and then release the lock.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case a dcss segment cannot be loaded blk_cleanup_queue
will be called before blk_queue_make_request, leaving the
struct work unplug_work of the request queue uninitialized
before it is used.
That leads also to the lockdep message below.
To avoid that call blk_queue_make_request right after the
request_queue has been allocated.
This makes sure that the struct work is always initialized
before it is used.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 2 Not tainted 2.6.24 #6
Process swapper (pid: 1, task: 000000000f854038, ksp: 000000000f85f980)
040000000f85f860 000000000f85f880 0000000000000002 0000000000000000
000000000f85f920 000000000f85f898 000000000f85f898 000000000001622e
0000000000000000 000000000f85f980 0000000000000000 0000000000000000
000000000f85f880 000000000000000c 000000000f85f880 000000000f85f8f0
0000000000342908 000000000001622e 000000000f85f880 000000000f85f8d0
Call Trace:
([<000000000001619e>] show_trace+0xda/0x104)
[<0000000000016288>] show_stack+0xc0/0xf8
[<00000000000163d0>] dump_stack+0xb0/0xc0
[<000000000006e4ea>] __lock_acquire+0x47e/0x1160
[<000000000006f27c>] lock_acquire+0xb0/0xd8
[<000000000005a522>] __cancel_work_timer+0x9e/0x240
[<000000000005a72e>] cancel_work_sync+0x2a/0x3c
[<0000000000165c46>] kblockd_flush_work+0x26/0x34
[<0000000000169034>] blk_sync_queue+0x38/0x48
[<0000000000169080>] blk_release_queue+0x3c/0xa8
[<000000000017bce8>] kobject_cleanup+0x58/0xac
[<000000000017bd66>] kobject_release+0x2a/0x38
[<000000000017d28e>] kref_put+0x6e/0x94
[<000000000017bc80>] kobject_put+0x38/0x48
[<00000000001653be>] blk_put_queue+0x2a/0x38
[<0000000000168fee>] blk_cleanup_queue+0x82/0x90
[<0000000000213e7e>] dcssblk_add_store+0x34e/0x700
[<00000000005243b8>] dcssblk_init+0x1a0/0x308
[<000000000050a3c2>] kernel_init+0x1b2/0x3a4
[<000000000001ac82>] kernel_thread_starter+0x6/0xc
[<000000000001ac7c>] kernel_thread_starter+0x0/0xc
INFO: lockdep is turned off.
Cc: Gerald Schaefer <geraldsc@de.ibm.com>
Cc: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When an alias device is set offline while it is in use this may
result in a panic in the cleanup part of the dasd_block_tasklet.
The problem here is that there may exist some ccw requests that were
originally created for the alias device and transferred to the base
device when the alias was set offline. When these request are
cleaned up later, the discipline pointer in the alias device may not
be valid anymore. To fix this use the base device discipline to find
the cleanup function.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Adding interface control check (ifcc) handling in error recovery.
First retry up to 255 times and if all retries fail try an alternate
path if possible.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch converts s390 to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
As a result, the interfaces of internal functions below are changed:
o dasd_end_request
o tapeblock_end_request
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add time to the 'expires' value to avoid a loop caused by the cqr
termination function
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Parallel access volumes (PAV) is a storage server feature, that allows
to start multiple channel programs on the same DASD in parallel. It
defines alias devices which can be used as alternative paths to the
same disk. With the old base PAV support we only needed rudimentary
functionality in the DASD device driver. As the mapping between base
and alias devices was static, we just had to export an identifier
(uid) and could leave the combining of devices to external layers
like a device mapper multipath.
Now hyper PAV removes the requirement to dedicate alias devices to
specific base devices. Instead each alias devices can be combined with
multiple base device on a per request basis. This requires full
support by the DASD device driver as now each channel program itself
has to identify the target base device.
The changes to the dasd device driver and the ECKD discipline are:
- Separate subchannel device representation (dasd_device) from block
device representation (dasd_block). Only base devices are block
devices.
- Gather information about base and alias devices and possible
combinations.
- For each request decide which dasd_device should be used (base or
alias) and build specific channel program.
- Support summary unit checks, which allow the storage server to
upgrade / downgrade between base and hyper PAV at runtime (support
is mandatory).
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
single list_head variable initialized with LIST_HEAD_INIT could almost
always can be replaced with LIST_HEAD declaration, this shrinks the code
and looks better.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Using the return value of ccw_device_set_online as return value for
dasd_generic_probe() causes the DASD to fail setting online
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When loading a dcss segment with the dcssblk driver, sometimes the
following kind of message appears:
bio too big device dcssblk0 (8 > 0)
Buffer I/O error on device dcssblk0, logical block 172016
..
The fix is to move the disk registration after setting the
make_request function, to avoid calls into generic_make_request
for dcssblock without having the make_request function set up
properly.
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Unregistering a device from within a device attribute handler leads to
a deadlock. Need to use device_schedule_callback() to unregister device
in error path.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Replacing n & (n - 1) for power of 2 check by is_power_of_2(n)
Signed-off-by: vignesh babu <vignesh.babu@wipro.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
As bi_end_io is only called once when the reqeust is complete,
the 'size' argument is now redundant. Remove it.
Now there is no need for bio_endio to subtract the size completed
from bi_size. So don't do that either.
While we are at it, change bi_end_io to return void.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Every usage of rq_for_each_bio wraps a usage of
bio_for_each_segment, so these can be combined into
rq_for_each_segment.
We define "struct req_iterator" to hold the 'bio' and 'index' that
are needed for the double iteration.
Signed-off-by: Neil Brown <neilb@suse.de>
Various compile fixes by me...
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
There are several s390 diagnose calls, which must be executed below the
2GB memory boundary. In order to enforce this, those diagnoses must be
compiled into the kernel. Currently diag 14 can be called within the
vmur kernel module from addresses above 2GB. This leads to specification
exceptions. This patch moves diag10, diag14 and diag210 into the new
diag.c file.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
No need to warn unregister_blkdev() failure by the callers. (The previous
patch makes unregister_blkdev() print error message in error case)
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/s390/block/dasd_proc.c:33:
warning: 'dasd_get_user_string' defined but not used
drivers/s390/block/dasd_proc.c:172:
warning: 'dasd_statistics_array' defined but not used
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Disband drivers/s390/Kconfig, use the common Kconfig files. The s390
specific config options from drivers/s390/Kconfig are moved to the
respective common Kconfig files.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The function shouldn't have existed in the first place (not MSS-aware).
Introduce a new function ccw_device_get_id() that extracts the
ccw_dev_id structure of a ccw device and convert all users of
_ccw_device_get_device_number to ccw_device_get_id.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Instead of the deprecated read_dev_chars() and read_conf_data_lpm(),
implement dasd_generic_read_dev_chars() and dasd_eckd_read_conf_lpm().
These should even recover better from error than the original cio
functions.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Specifying 'ipldev' in the dasd= kernel parameter will automatically
activate the boot device for use by the dasd driver.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch adds a sysfs-attribute 'status' to make the DASD device-status
accessible from user-space. In addition, the DASD driver generates an
uevent(CHANGE) for the ccw-device on each device-status change.
This enables user-space applications (e.g. udev) to do related processing.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
gcc incorrectly removes initialization of register 0 in dasd diag
inline assembly. Use different register to work around this compiler
bug.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
For extended error reporting we sometimes have to start an
Sense Subsystem Status request (SNSS). When this request needs
to be recovered for some reason, the recovery request will
fail with 'command reject'.
Our usual recovery procedure will retry the failed request by
creating a new request and chaining the failed request from that
one. SNSS requests, though, must not be chained from anything,
so the recovery request will fail permanently.
Use the default recovery for SNSS request, which will just restart
the original request without further ado.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for clock synchronization to an external time
reference (ETR). The external time reference sends an oscillator
signal and a synchronization signal every 2^20 microseconds to keep
the TOD clocks of all connected servers in sync. For availability
two ETR units can be connected to a machine. If the clock deviates
for more than the sync-check tolerance all cpus get a machine check
that indicates that the clock is out of sync. For the lovely details
how to get the clock back in sync see the code below.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The reserve/release IOCTLs sometimes do not work. If second system
does a 'steal lock' the pending unit check (Format 3 Msg F) is
delivered. Since ERP is disabled for reserve/release, the IOCTL call
fails. We have to allow basic ERP (retries) for reserve/release IOCTLs.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Logging of relevant information is already done by disciplines
dump_sense function.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently loaded DCSS segments are now listed in /proc/iomem with
their name followed by a trailing "(DCSS)".
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The initialization of the dasd_eer code is one of the last steps of the
dasd driver initialization. When initialization fails in one of the
earlier steps, the dasd_exit function is called to clean up what has been
done so far. So the dasd_eer_exit function may be called, although the
dasd_eer_init function wasn't called before and dasd_eer_exit tries to
unregister a misc device that wasn't registered, which results in a BUG.
Make sure that dasd_eer_exit can be called without initialization. Use a
dynamically allocated struct miscdevice instead of a static one, so we
only try to unregister the device if it exists and was actually registered.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Poison init section before freeing it.
[S390] Use add_active_range() and free_area_init_nodes().
[S390] Virtual memmap for s390.
[S390] Update documentation for dynamic subchannel mapping.
[S390] Use dev->groups for adding/removing the subchannel attribute group.
[S390] Support for disconnected devices reappearing on another subchannel.
[S390] subchannel lock conversion.
[S390] Some preparations for the dynamic subchannel mapping patch.
[S390] runtime switch for qdio performance statistics
[S390] New DASD feature for ERP related logging
[S390] add reset call handler to the ap bus.
[S390] more workqueue fixes.
[S390] workqueue fixes.
[S390] uaccess_pt: add missing down_read() and convert to is_init().
It is now possible to enable/disable ERP related logging without re-compile
and re-ipl. A additional sysfs-attribute 'erplog' allows to switch the
logging non-interruptive.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_DMA is an alias of GFP_DMA. This is the last one so we
remove the leftover comment too.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently the return value of 'dasd_eer_enable' is returned - even if the
function returned '0'. Now return 'count' for successful execution.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case a request timed out and termination did not work, the console was
flooded with retry messages (every 1/10s). Now we use a 5s delay per retry and
generate a more precise message.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When writing to dasd attributes (e.g. readonly), all values besides '1'
are handled like '0'.
Other sysfs-attributes like 'online' are checking for '1' and for '0'
and do not accept other values. Therefore enhanced checking and error
handling in dasd_devmap attribute store functions.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Clean up dasd timer when when a dasd device is set offline.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make it possible to disable the block layer. Not all embedded devices require
it, some can make do with just JFFS2, NFS, ramfs, etc - none of which require
the block layer to be present.
This patch does the following:
(*) Introduces CONFIG_BLOCK to disable the block layer, buffering and blockdev
support.
(*) Adds dependencies on CONFIG_BLOCK to any configuration item that controls
an item that uses the block layer. This includes:
(*) Block I/O tracing.
(*) Disk partition code.
(*) All filesystems that are block based, eg: Ext3, ReiserFS, ISOFS.
(*) The SCSI layer. As far as I can tell, even SCSI chardevs use the
block layer to do scheduling. Some drivers that use SCSI facilities -
such as USB storage - end up disabled indirectly from this.
(*) Various block-based device drivers, such as IDE and the old CDROM
drivers.
(*) MTD blockdev handling and FTL.
(*) JFFS - which uses set_bdev_super(), something it could avoid doing by
taking a leaf out of JFFS2's book.
(*) Makes most of the contents of linux/blkdev.h, linux/buffer_head.h and
linux/elevator.h contingent on CONFIG_BLOCK being set. sector_div() is,
however, still used in places, and so is still available.
(*) Also made contingent are the contents of linux/mpage.h, linux/genhd.h and
parts of linux/fs.h.
(*) Makes a number of files in fs/ contingent on CONFIG_BLOCK.
(*) Makes mm/bounce.c (bounce buffering) contingent on CONFIG_BLOCK.
(*) set_page_dirty() doesn't call __set_page_dirty_buffers() if CONFIG_BLOCK
is not enabled.
(*) fs/no-block.c is created to hold out-of-line stubs and things that are
required when CONFIG_BLOCK is not set:
(*) Default blockdev file operations (to give error ENODEV on opening).
(*) Makes some /proc changes:
(*) /proc/devices does not list any blockdevs.
(*) /proc/diskstats and /proc/partitions are contingent on CONFIG_BLOCK.
(*) Makes some compat ioctl handling contingent on CONFIG_BLOCK.
(*) If CONFIG_BLOCK is not defined, makes sys_quotactl() return -ENODEV if
given command other than Q_SYNC or if a special device is specified.
(*) In init/do_mounts.c, no reference is made to the blockdev routines if
CONFIG_BLOCK is not defined. This does not prohibit NFS roots or JFFS2.
(*) The bdflush, ioprio_set and ioprio_get syscalls can now be absent (return
error ENOSYS by way of cond_syscall if so).
(*) The seclvl_bd_claim() and seclvl_bd_release() security calls do nothing if
CONFIG_BLOCK is not set, since they can't then happen.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Right now ->flags is a bit of a mess: some are request types, and
others are just modifiers. Clean this up by splitting it into
->cmd_type and ->cmd_flags. This allows introduction of generic
Linux block message types, useful for sending generic Linux commands
to block devices.
Signed-off-by: Jens Axboe <axboe@suse.de>
Major cleanup of all s390 inline assemblies. They now have a common
coding style. Quite a few have been shortened, mainly by using register
asm variables. Use of the EX_TABLE macro helps as well. The atomic ops,
bit ops and locking inlines new use the Q-constraint if a newer gcc
is used. That results in slightly better code.
Thanks to Christian Borntraeger for proof reading the changes.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Specifying kernel parameter "dasd=nopav" on systems running under VM
has no function but results in message "disable PAV mode". Correct
message is "'nopav' not supported on VM".
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The xpram driver shows and uses 4096 bytes less than available.
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Enhanced default DBF level to get most important messages
in debug feature files.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The dasd_device_from_cdev function is called from interrupt context
to get the struct dasd_device associated with a ccw device. The
driver_data of the ccw device points to the dasd_devmap structure
which contains the pointer to the dasd_device structure. The lock
that protects the dasd_devmap structure is acquire with out irqsave.
To prevent the deadlock in dasd_device_from_cdev if it is called
from interrupt context the dependency to the dasd_devmap structure
needs to be removed. Let the driver_data of the ccw device point
to the dasd_device structure directly and use the ccw device lock
to protect the access.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix clear_IO handling (need to wait for interrupt) and
introduced error-handling in shutdown processing.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The subsystem check in the PAV code is incorrect, it enables PAV
per device instead of per subsystem.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In some situations PAV alias devices on LPAR are not accessible.
The initialization procedure required to enable access to PAV alias
devices has to be performed per storage server subsystem and not
only once per storage server.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The dasd_page_cache should return page addresses and therefore the
cache must be created with an alignment of PAGE_SIZE.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The dasd function dasd_set_uid calls kzalloc while holding the
dasd_devmap_lock. Rearrange the code to do the memory allocation
outside the lock.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The request queue flush function of the dasd driver has to dequeue
the requests first and then call the end request function. Otherwise
a kernel bug in ll_rw_block.c might get triggered.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove system device class for xpram. It creates the directory hierarchy
under /sys/devices/system/xpram/xpram0. The xpram0 directory is empty and
it is always created while xpram1 and following devices are always missing,
independent if the devices exist or not. Since the xpram devices are
listed in /proc/partitions and /sys/block/ as slram<x> the system device
class for xpram is meaningless.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Don't use memparse since the default size modifier is 'k'.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The module parameters for xpram are not or in a wrong way parsed.
The xpram module uses the module_param_array directive with an int
parameter which causes the kernel to automatically parse the passed
numbers. This will cause errors if arguments are omitted or cause
wrong results if arguments have size qualifiers.
Use module_param_array with charp and parse the arguments later.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
Add support for parallel-access-volumes to the dasd driver. This
allows concurrent access to dasd devices with multiple channel
programs.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The struct dasd_eer_header needs the packed attribute, or there will
be 6 additional bytes of random data between the fixed header and
the variable length part of the eer data.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Dasd code cleanup: 1) remove white space, 2) remove the emacs override
sections, and 3) use kzalloc instead of kmalloc.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The ccw dump function dasd_eckd_dump_ccw_range can crash because
it does not take care about the IDAL flag in the ccw.
Check for IDALs flag set in CCW and follow the indirect list to
print the data that is refered by the ccw.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Check the return value of kzalloc in dasd_eer_open.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
locking init cleanups:
- convert " = SPIN_LOCK_UNLOCKED" to spin_lock_init() or DEFINE_SPINLOCK()
- convert rwlocks in a similar manner
this patch was generated automatically.
Motivation:
- cleanliness
- lockdep needs control of lock initialization, which the open-coded
variants do not give
- it's also useful for -rt and for lock debugging in general
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Generate new sysfs-attribute 'uid' that contains an device specific unique
identifier. This can be used to identity multiple ALIASES of the same
physical device (PAV). In addition the sysfs-attributes 'vendor' (containing
the manufacturer of the device) and 'alias' (identify alias or base device) is
added. This is first part of PAV support in LPAR (also valid on zVM).
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The dasd state machine is not designed to enable an unformatted device, since
'unformatted' is a final state. The BIODASDENABLE ioctl calls
dasd_enable_device() which never returns if the device is in this special
state. Return -EPERM in dasd_increase_state for unformatted devices to make
dasd_enable_device terminate. Note: To get such an unformatted device online
it has to be re-analyzed. This means that the device needs to be disabled
prior to re-enablement.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The proc_mkdir calls in the dasd driver are not check for NULL pointers. Add
code to check the pointers and bail out if one of the proc entries could not
be created.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Using the fail-fast flag in i/o requests on a dasd disk which has been
quiesced leads to kernel panics. Modify the request start function to only
work on requests in a valid state.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The dasd driver sometimes print the misleading message "Can't offline dasd
device with open count = 0". The reason why it can't offline the device in
this case is that the device is still in the startup phase. Print a more
meaningful message.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (21 commits)
BUG_ON() Conversion in drivers/video/
BUG_ON() Conversion in drivers/parisc/
BUG_ON() Conversion in drivers/block/
BUG_ON() Conversion in sound/sparc/cs4231.c
BUG_ON() Conversion in drivers/s390/block/dasd.c
BUG_ON() Conversion in lib/swiotlb.c
BUG_ON() Conversion in kernel/cpu.c
BUG_ON() Conversion in ipc/msg.c
BUG_ON() Conversion in block/elevator.c
BUG_ON() Conversion in fs/coda/
BUG_ON() Conversion in fs/binfmt_elf_fdpic.c
BUG_ON() Conversion in input/serio/hil_mlc.c
BUG_ON() Conversion in md/dm-hw-handler.c
BUG_ON() Conversion in md/bitmap.c
The comment describing how MS_ASYNC works in msync.c is confusing
rcu: undeclared variable used in documentation
fix typos "wich" -> "which"
typo patch for fs/ufs/super.c
Fix simple typos
tabify drivers/char/Makefile
...
MODULE_PARM was actually breaking: recent gcc version optimize them out as
unused. It's time to replace the last users, which are generally in the
most unloved drivers anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Convert all kmalloc + memset sequences in drivers/s390 to kzalloc usage.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The DASD extended error reporting is a facility that allows to get detailed
information about certain problems in the DASD I/O. This information can be
used to implement fail-over applications that can recover these problems.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use kzalloc to get a zeroed buffer for the structure returned to user space by
the BIODASDINFO2 ioctl. Not all fields are set up, e.g. the read_devno is
missing.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The dasd diag discipline has been tested on 64 bit and is no longer
experimental.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that there are no more users of the awkward dynamic ioctl hack we can
remove the code to support it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
dasd_cmd just implements three ioctls which are wrappers around functionality
in the core kernel or other modules. When merging those into dasd_mod they
just add 22 lines of code which is far less than the amount of code removed in
the last two patches, and which doesn't spill into another 4k pages when build
modular, while removing a 128lines module.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add an ->ioctl method to the dasd_discipline structure. This allows to apply
the same kind of cleanups the last patch applied to dasd_ioctl.c to
dasd_eckd.c (the only dasd discipline with special ioctls) aswell.
Again lots of code removed. During auditing the ioctls I found two fishy
return value propagations from copy_{from,to}_user, maintainers please check
those, I've marked them with XXX comments.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Handle ioctls implemented in dasd_ioctl through the normal switch statement
that most drivers use instead of the awkward dasd_ioctl_no_register routine.
This avoids searching a linear list on every call to dasd_ioctl(), and allows
to give the various ioctl implementation functions sane prototypes, aswell as
moving the check for bdev->bd_disk->private_data from the individual functions
to dasd_ioctl. (I think it can't actually every be NULL, but let's keep that
for later)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
DASD allows to open a device as soon as gendisk is registered, which means the
device is a fake device (capacity=0) and we do know nothing about blocksize
and partitions at that point of time. In case the device is opened by
someone, the bdev and inode creation is done with the fake device info and the
following partition detection code is just using the wrong data.
To avoid this modify the DASD state machine to make sure that the open is
rejected until the device analysis is either finished or an unformatted device
was detected.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Revert dasd eer module until we have a common understanding of how the
interface should be.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When using the dasd diag discipline, the base discipline module (eckd or fba)
can be unloaded, even though the dasd driver requires both discipline modules
(base and diag) to work correctly.
Implement reference counting for both base and diag discipline modules in
order to fix this.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The DASD extended error reporting is a facility that allows to get detailed
information about certain problems in the DASD I/O. This information can be
used to implement fail-over applications that can recover these problems.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The sleep_on function clears a running cqr without waiting for the related
interrupt. This can lead to a panic at the time the interrupt is processed
because the related memory might already be freed. Wait for clear-interrupt
and de-queue cqr prior to return.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The open_count is increased for every opener, that includes the blkdev_get in
dasd_scan_partitions. This tampers the open_count in BIODASDINFO. Hide the
internal open from user-space.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove all CVS generated information like e.g. revision IDs from
drivers/s390 and include/asm-s390 (none present in arch/s390).
- Add newline at end of arch/s390/lib/Makefile to avoid diff message.
Acked-by: Andreas Herrmann <aherrman@de.ibm.com>
Acked-by: Frank Pavlic <pavlic@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The QUEUE_ORDERED_* numbers got renumbered and by accident the dasd driver
was changed to use QUEUE_ORDERED_DRAIN instead of QUEUE_ORDERED_TAG.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the missing third argument to the blk_queue_ordered call and use the
constant QUEUE_ORDERED_DRAIN instead of "1".
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a compat_ioctl method to the dasd driver so the last entries in
arch/s390/kernel/compat_ioctl.c can go away. Unlike the previous attempt this
one does not replace the ioctl method with an unlocked_ioctl method so that
the ioctl_by_bdev calls in s390 partition code continue to work.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
HDIO_GETGEO is implemented in most block drivers, and all of them have to
duplicate the code to copy the structure to userspace, as well as getting
the start sector. This patch moves that to common code [1] and adds a
->getgeo method to fill out the raw kernel hd_geometry structure. For many
drivers this means ->ioctl can go away now.
[1] the s390 block drivers are odd in this respect. xpram sets ->start
to 4 always which seems more than odd, and the dasd driver shifts
the start offset around, probably because of it's non-standard
sector size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@suse.de>
Cc: <mike.miller@hp.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sanitize some s390 Kconfig options. We have ARCH_S390, ARCH_S390X,
ARCH_S390_31, 64BIT, S390_SUPPORT and COMPAT. Replace these 6 options by
S390, 64BIT and COMPAT.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To properly support multipath-failover handling, the linux block layer has
introduced a special request flag, 'REQ_FAILFAST'. This flag is now used to
return requests immediately in case the device is not operational.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The IOCTL BIODASDPRRD had no return code for 'profiling is inactive' and
therefore tunedasd wrote misleading message for request-counter = 0.
Introduce return-code EIO for inactive profiling.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Extract the s390_root_dev_* functions from the common I/O layer as they are
also used by non-ccw device drivers.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Moved definition of CMS volume label to vtoc.h and modify partitions/ibm.c to
use this volume label definition instead of anonymous array.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hugh Dickins <hugh@veritas.com>
Fix the broken atomic_cmpxchg primitive. Add atomic_sub_and_test,
atomic64_sub_return, atomic64_sub_and_test, atomic64_cmpxchg,
atomic64_add_unless and atomic64_inc_not_zero. Replace old style
atomic_compare_and_swap by atomic_cmpxchg. Shorten the whole header by
defining most primitives with the two inline functions atomic_add_return and
atomic_sub_return.
In addition this patch contains the s390 related fixes of Hugh's "mm: fill
arch atomic64 gaps" patch.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
add @uptodate argument to end_that_request_last() and @error
to rq_end_io_fn(). there's no generic way to pass error code
to request completion function, making generic error handling
of non-fs request difficult (rq->errors is driver-specific and
each driver uses it differently). this patch adds @uptodate
to end_that_request_last() and @error to rq_end_io_fn().
for fs requests, this doesn't really matter, so just using the
same uptodate argument used in the last call to
end_that_request_first() should suffice. imho, this can also
help the generic command-carrying request jens is working on.
Signed-off-by: tejun heo <htejun@gmail.com>
Signed-Off-By: Jens Axboe <axboe@suse.de>
This is the drivers/s390/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in drivers/s390/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Cornelia Huck <cohuck@de.ibm.com>
Acked-by: Stefan Bader <Stefan.Bader@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Access to FBA disks via DIAG fails for block sizes > 512 byte. The device
analysis code of the DIAG discipline does not properly initialize the DIAG250
device environment after completion of the analysis. This results in VM only
serving 512 bytes per block I/O request whereas Linux expects larger block
sizes. Add proper device environment setup to end of analysis code.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Future versions of gcc may remove initialization code for control blocks used
by the diag250 inline assembly due to incompletely specified constraints.
This may lead to erratic behavior. Fix the diag250 inline assembly
constraints.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for diag 250 access to dasd devices for 64 bit kernels. In
addition fix detach/attach for diag disks. The VM control block needs to get
recreated by a call to mdsk_init_io.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reintroduce a read-only copy of the devmap features in the device struct.
This is necessary to solve a deadlock on the dasd_devmap_lock which is
acquired by dasd_get_features called from the dasd tasklet. The current
implementation of devmap doesn't allow to call any devmap function from
interrupt or softirq context.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The FBA discipline does not use retries for failed requests. A request fails
after the first unsuccessful start attempt. There are some rare conditions
(e.g. CIO path recovery) in which the start of an i/o on a fba device can
fail. A tiny amount of retries is therefore reasonable.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes the memory allocation method for the s390 debug feature.
Trace buffers had been allocated using the get_free_pages() function before.
Therefore it was not possible to get big memory areas in a running system due
to memory fragmentation. Now the trace buffers are subdivided into several
subbuffers with pagesize. Therefore it is now possible to allocate more
memory for the trace buffers and more trace records can be written.
In addition to that, dynamic specification of the size of the trace buffers is
implemented. It is now possible to change the size of a trace buffer using a
new debugfs file instance. When writing a number into this file, the trace
buffer size is changed to 'number * pagesize'.
In the past all the traces could be obtained from userspace by accessing files
in the "proc" filesystem. Now with debugfs we have a new filesystem which
should be used for debugging purposes. This patch moves the debug feature
from procfs to debugfs.
Since the interface of debug_register() changed, all device drivers, which use
the debug feature had to be adjusted.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix compile breakage in the dcss block driver introduced by the attribute
changes.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert the dasd driver to use the new klist interface.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the block device related part. The block device operation
direct_access now has a struct block_device as first parameter.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jean-Baptiste Joret