As long as we recover one metadata block, we should write the empty metadata
write. The original code could make recovery corrupted if only one meta is
valid.
Reported-by: Zhengyuan Liu <liuzhengyuan@kylinos.cn>
Signed-off-by: Shaohua Li <shli@fb.com>
If there is a bad block on a disk and there is a recovery performed from
this disk, the same bad block is reported for a new disk. It involves
setting MD_CHANGE_PENDING flag in rdev_set_badblocks. For external
metadata this flag is not being cleared as array state is reported as
'clean'. The read request to bad block in RAID5 array gets stuck as it
is waiting for a flag to be cleared - as per commit c3cce6cda1
("md/raid5: ensure device failure recorded before write request
returns.").
The meaning of MD_CHANGE_PENDING and MD_CHANGE_CLEAN flags has been
clarified in commit 070dc6dd71 ("md: resolve confusion of
MD_CHANGE_CLEAN"), however MD_CHANGE_PENDING flag has been used in
personality error handlers since and it doesn't fully comply with
initial purpose. It was supposed to notify that write request is about
to start, however now it is also used to request metadata update.
Initially (in md_allow_write, md_write_start) MD_CHANGE_PENDING flag has
been set and in_sync has been set to 0 at the same time. Error handlers
just set the flag without modifying in_sync value. Sysfs array state is
a single value so now it reports 'clean' when MD_CHANGE_PENDING flag is
set and in_sync is set to 1. Userspace has no idea it is expected to
take some action.
Swap the order that array state is checked so 'write_pending' is
reported ahead of 'clean' ('write_pending' is a misleading name but it
is too late to rename it now).
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
If superblock points to an invalid meta block, r5l_load_log will set
create_super with true and create an new superblock, this runtime path
would always happen if we do no writing I/O to this array since it was
created. Writing an empty meta block could avoid this unnecessary
action at the first time we created log superblock.
Another reason is for the corretness of log recovery. Currently we have
bellow code to guarantee log revocery to be correct.
if (ctx.seq > log->last_cp_seq + 1) {
int ret;
ret = r5l_log_write_empty_meta_block(log, ctx.pos, ctx.seq + 10);
if (ret)
return ret;
log->seq = ctx.seq + 11;
log->log_start = r5l_ring_add(log, ctx.pos, BLOCK_SECTORS);
r5l_write_super(log, ctx.pos);
} else {
log->log_start = ctx.pos;
log->seq = ctx.seq;
}
If we just created a array with a journal device, log->log_start and
log->last_checkpoint should all be 0, then we write three meta block
which are valid except mid one and supposed crash happened. The ctx.seq
would equal to log->last_cp_seq + 1 and log->log_start would be set to
position of mid invalid meta block after we did a recovery, this will
lead to problems which could be avoided with this patch.
Signed-off-by: Zhengyuan Liu <liuzhengyuan@kylinos.cn>
Signed-off-by: Shaohua Li <shli@fb.com>
No initial operation was done to this field when we
load/recovery the log, it got assignment only when IO
to raid disk was finished. So r5l_quiesce may use wrong
next_checkpoint to reclaim log space, that would make
reclaimable space calculation confused.
Signed-off-by: Zhengyuan Liu <liuzhengyuan@kylinos.cn>
Signed-off-by: Shaohua Li <shli@fb.com>
This is the counterpart of raid10 fix. If a write error occurs, raid10
will try to rewrite the bio in small chunk size. If the rewrite fails,
raid10 will record the error in bad block. narrow_write_error will
always use WRITE for the bio, but actually it could be a discard. Since
discard bio hasn't payload, write the bio will cause different issues.
But discard error isn't fatal, we can safely ignore it. This is what
this patch does.
This issue should exist since discard is added, but only exposed with
recent arbitrary bio size feature.
Cc: Sitsofe Wheeler <sitsofe@gmail.com>
Cc: stable@vger.kernel.org (v3.6)
Signed-off-by: Shaohua Li <shli@fb.com>
If a write error occurs, raid1 will try to rewrite the bio in small
chunk size. If the rewrite fails, raid1 will record the error in bad
block. narrow_write_error will always use WRITE for the bio, but
actually it could be a discard. Since discard bio hasn't payload, write
the bio will cause different issues. But discard error isn't fatal, we
can safely ignore it. This is what this patch does.
This issue should exist since discard is added, but only exposed with
recent arbitrary bio size feature.
Reported-and-tested-by: Sitsofe Wheeler <sitsofe@gmail.com>
Cc: stable@vger.kernel.org (v3.6)
Signed-off-by: Shaohua Li <shli@fb.com>
A good practice is to prefix the names of functions by the name
of the subsystem.
The kthread worker API is a mix of classic kthreads and workqueues. Each
worker has a dedicated kthread. It runs a generic function that process
queued works. It is implemented as part of the kthread subsystem.
This patch renames the existing kthread worker API to use
the corresponding name from the workqueues API prefixed by
kthread_:
__init_kthread_worker() -> __kthread_init_worker()
init_kthread_worker() -> kthread_init_worker()
init_kthread_work() -> kthread_init_work()
insert_kthread_work() -> kthread_insert_work()
queue_kthread_work() -> kthread_queue_work()
flush_kthread_work() -> kthread_flush_work()
flush_kthread_worker() -> kthread_flush_worker()
Note that the names of DEFINE_KTHREAD_WORK*() macros stay
as they are. It is common that the "DEFINE_" prefix has
precedence over the subsystem names.
Note that INIT() macros and init() functions use different
naming scheme. There is no good solution. There are several
reasons for this solution:
+ "init" in the function names stands for the verb "initialize"
aka "initialize worker". While "INIT" in the macro names
stands for the noun "INITIALIZER" aka "worker initializer".
+ INIT() macros are used only in DEFINE() macros
+ init() functions are used close to the other kthread()
functions. It looks much better if all the functions
use the same scheme.
+ There will be also kthread_destroy_worker() that will
be used close to kthread_cancel_work(). It is related
to the init() function. Again it looks better if all
functions use the same naming scheme.
+ there are several precedents for such init() function
names, e.g. amd_iommu_init_device(), free_area_init_node(),
jump_label_init_type(), regmap_init_mmio_clk(),
+ It is not an argument but it was inconsistent even before.
[arnd@arndb.de: fix linux-next merge conflict]
Link: http://lkml.kernel.org/r/20160908135724.1311726-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/1470754545-17632-3-git-send-email-pmladek@suse.com
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull blk-mq irq/cpu mapping updates from Jens Axboe:
"This is the block-irq topic branch for 4.9-rc. It's mostly from
Christoph, and it allows drivers to specify their own mappings, and
more importantly, to share the blk-mq mappings with the IRQ affinity
mappings. It's a good step towards making this work better out of the
box"
* 'for-4.9/block-irq' of git://git.kernel.dk/linux-block:
blk_mq: linux/blk-mq.h does not include all the headers it depends on
blk-mq: kill unused blk_mq_create_mq_map()
blk-mq: get rid of the cpumask in struct blk_mq_tags
nvme: remove the post_scan callout
nvme: switch to use pci_alloc_irq_vectors
blk-mq: provide a default queue mapping for PCI device
blk-mq: allow the driver to pass in a queue mapping
blk-mq: remove ->map_queue
blk-mq: only allocate a single mq_map per tag_set
blk-mq: don't redistribute hardware queues on a CPU hotplug event
. add support for delaying the requeue of requests; used by DM multipath
when all paths have failed and 'queue_if_no_path' is enabled
. DM cache improvements to speedup the loading metadata and the writing
of the hint array
. fix potential for a dm-crypt crash on device teardown
. remove dm_bufio_cond_resched() and just using cond_resched()
. change DM multipath to return a reservation conflict error
immediately; rather than failing the path and retrying (potentially
indefinitely)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJX7n9KAAoJEMUj8QotnQNab74IANm+rW2uYdpLNCxWUmcaih0d
BK8dLS/Mz35S0TRSekvynuBcPx18VP2Zueulc+aHTWcT4sj79l6KnVYT9g6c98rL
zzcv10QTteqhiiWwFmPHsZgv5dW8Y5wiRdt+SqcQ5sAHMFci6C05gzp9caNu7VTs
fbcLUdyYm40y3j84Lx/+ABXgnBhq+40OTtdnYSkEmLtdscPLzwpHgPmMctkrEl7e
7mqGC1KbDDzartqOZOeGP2P2qOCNN21qA+8ctMw9Xyze33uwvj7Vx6cro6e28wMm
ZClY9XNGlfuW9dCNtFR9o6NXS6NIK30UJbKqyZPPsK+70JrOgzh6GzQnwSXdyNs=
=7SkG
-----END PGP SIGNATURE-----
Merge tag 'dm-4.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- various fixes and cleanups for request-based DM core
- add support for delaying the requeue of requests; used by DM
multipath when all paths have failed and 'queue_if_no_path' is
enabled
- DM cache improvements to speedup the loading metadata and the writing
of the hint array
- fix potential for a dm-crypt crash on device teardown
- remove dm_bufio_cond_resched() and just using cond_resched()
- change DM multipath to return a reservation conflict error
immediately; rather than failing the path and retrying (potentially
indefinitely)
* tag 'dm-4.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (24 commits)
dm mpath: always return reservation conflict without failing over
dm bufio: remove dm_bufio_cond_resched()
dm crypt: fix crash on exit
dm cache metadata: switch to using the new cursor api for loading metadata
dm array: introduce cursor api
dm btree: introduce cursor api
dm cache policy smq: distribute entries to random levels when switching to smq
dm cache: speed up writing of the hint array
dm array: add dm_array_new()
dm mpath: delay the requeue of blk-mq requests while all paths down
dm mpath: use dm_mq_kick_requeue_list()
dm rq: introduce dm_mq_kick_requeue_list()
dm rq: reduce arguments passed to map_request() and dm_requeue_original_request()
dm rq: add DM_MAPIO_DELAY_REQUEUE to delay requeue of blk-mq requests
dm: convert wait loops to use autoremove_wake_function()
dm: use signal_pending_state() in dm_wait_for_completion()
dm: rename task state function arguments
dm: add two lockdep_assert_held() statements
dm rq: simplify dm_old_stop_queue()
dm mpath: check if path's request_queue is dying in activate_path()
...
Pull block layer updates from Jens Axboe:
"This is the main pull request for block layer changes in 4.9.
As mentioned at the last merge window, I've changed things up and now
do just one branch for core block layer changes, and driver changes.
This avoids dependencies between the two branches. Outside of this
main pull request, there are two topical branches coming as well.
This pull request contains:
- A set of fixes, and a conversion to blk-mq, of nbd. From Josef.
- Set of fixes and updates for lightnvm from Matias, Simon, and Arnd.
Followup dependency fix from Geert.
- General fixes from Bart, Baoyou, Guoqing, and Linus W.
- CFQ async write starvation fix from Glauber.
- Add supprot for delayed kick of the requeue list, from Mike.
- Pull out the scalable bitmap code from blk-mq-tag.c and make it
generally available under the name of sbitmap. Only blk-mq-tag uses
it for now, but the blk-mq scheduling bits will use it as well.
From Omar.
- bdev thaw error progagation from Pierre.
- Improve the blk polling statistics, and allow the user to clear
them. From Stephen.
- Set of minor cleanups from Christoph in block/blk-mq.
- Set of cleanups and optimizations from me for block/blk-mq.
- Various nvme/nvmet/nvmeof fixes from the various folks"
* 'for-4.9/block' of git://git.kernel.dk/linux-block: (54 commits)
fs/block_dev.c: return the right error in thaw_bdev()
nvme: Pass pointers, not dma addresses, to nvme_get/set_features()
nvme/scsi: Remove power management support
nvmet: Make dsm number of ranges zero based
nvmet: Use direct IO for writes
admin-cmd: Added smart-log command support.
nvme-fabrics: Add host_traddr options field to host infrastructure
nvme-fabrics: revise host transport option descriptions
nvme-fabrics: rework nvmf_get_address() for variable options
nbd: use BLK_MQ_F_BLOCKING
blkcg: Annotate blkg_hint correctly
cfq: fix starvation of asynchronous writes
blk-mq: add flag for drivers wanting blocking ->queue_rq()
blk-mq: remove non-blocking pass in blk_mq_map_request
blk-mq: get rid of manual run of queue with __blk_mq_run_hw_queue()
block: export bio_free_pages to other modules
lightnvm: propagate device_add() error code
lightnvm: expose device geometry through sysfs
lightnvm: control life of nvm_dev in driver
blk-mq: register device instead of disk
...
Pull MD updates from Shaohua Li:
"This update includes:
- new AVX512 instruction based raid6 gen/recovery algorithm
- a couple of md-cluster related bug fixes
- fix a potential deadlock
- set nonrotational bit for raid array with SSD
- set correct max_hw_sectors for raid5/6, which hopefuly can improve
performance a little bit
- other minor fixes"
* tag 'md/4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md: set rotational bit
raid6/test/test.c: bug fix: Specify aligned(alignment) attributes to the char arrays
raid5: handle register_shrinker failure
raid5: fix to detect failure of register_shrinker
md: fix a potential deadlock
md/bitmap: fix wrong cleanup
raid5: allow arbitrary max_hw_sectors
lib/raid6: Add AVX512 optimized xor_syndrome functions
lib/raid6/test/Makefile: Add avx512 gen_syndrome and recovery functions
lib/raid6: Add AVX512 optimized recovery functions
lib/raid6: Add AVX512 optimized gen_syndrome functions
md-cluster: make resync lock also could be interruptted
md-cluster: introduce dlm_lock_sync_interruptible to fix tasks hang
md-cluster: convert the completion to wait queue
md-cluster: protect md_find_rdev_nr_rcu with rcu lock
md-cluster: clean related infos of cluster
md: changes for MD_STILL_CLOSED flag
md-cluster: remove some unnecessary dlm_unlock_sync
md-cluster: use FORCEUNLOCK in lockres_free
md-cluster: call md_kick_rdev_from_array once ack failed
Pull CPU hotplug updates from Thomas Gleixner:
"Yet another batch of cpu hotplug core updates and conversions:
- Provide core infrastructure for multi instance drivers so the
drivers do not have to keep custom lists.
- Convert custom lists to the new infrastructure. The block-mq custom
list conversion comes through the block tree and makes the diffstat
tip over to more lines removed than added.
- Handle unbalanced hotplug enable/disable calls more gracefully.
- Remove the obsolete CPU_STARTING/DYING notifier support.
- Convert another batch of notifier users.
The relayfs changes which conflicted with the conversion have been
shipped to me by Andrew.
The remaining lot is targeted for 4.10 so that we finally can remove
the rest of the notifiers"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
cpufreq: Fix up conversion to hotplug state machine
blk/mq: Reserve hotplug states for block multiqueue
x86/apic/uv: Convert to hotplug state machine
s390/mm/pfault: Convert to hotplug state machine
mips/loongson/smp: Convert to hotplug state machine
mips/octeon/smp: Convert to hotplug state machine
fault-injection/cpu: Convert to hotplug state machine
padata: Convert to hotplug state machine
cpufreq: Convert to hotplug state machine
ACPI/processor: Convert to hotplug state machine
virtio scsi: Convert to hotplug state machine
oprofile/timer: Convert to hotplug state machine
block/softirq: Convert to hotplug state machine
lib/irq_poll: Convert to hotplug state machine
x86/microcode: Convert to hotplug state machine
sh/SH-X3 SMP: Convert to hotplug state machine
ia64/mca: Convert to hotplug state machine
ARM/OMAP/wakeupgen: Convert to hotplug state machine
ARM/shmobile: Convert to hotplug state machine
arm64/FP/SIMD: Convert to hotplug state machine
...
if all disks in an array are non-rotational, set the array
non-rotational.
This only works for array with all disks populated at startup. Support
for disk hotadd/hotremove could be added later if necessary.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Shaohua Li <shli@fb.com>
If dm-mpath encounters an reservation conflict it should not fail the
path (as communication with the target is not affected) but should
rather retry on another path. However, in doing so we might be inducing
a ping-pong between paths, with no guarantee of any forward progress.
And arguably a reservation conflict is an unexpected error, so we should
be passing it upwards to allow the application to take appropriate
steps.
This change resolves a show-stopper problem seen with the pNFS SCSI
layout because it is trivial to hit reservation conflict based failover
loops without it.
Doubts were raised about the implications of this change relative to
products like IBM's SVC. But there is little point withholding a fix
for Linux because a proprietary product may or may not have some issues
in its implementation of how it interfaces with Linux. In the future,
if there is glaring evidence that this change is certainly problematic
we can revisit it.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com> # tweaked header
Use cond_resched() like everybody else.
Mikulas explained why dm_bufio_cond_resched() was introduced to begin
with (hopefully cond_resched can be improved accordingly) here:
https://www.redhat.com/archives/dm-devel/2016-September/msg00112.html
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Alasdair Kergon <agk@redhat.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com> # added last comment in header
As the documentation for kthread_stop() says, "if threadfn() may call
do_exit() itself, the caller must ensure task_struct can't go away".
dm-crypt does not ensure this and therefore crashes when crypt_dtr()
calls kthread_stop(). The crash is trivially reproducible by adding a
delay before the call to kthread_stop() and just opening and closing a
dm-crypt device.
general protection fault: 0000 [#1] PREEMPT SMP
CPU: 0 PID: 533 Comm: cryptsetup Not tainted 4.8.0-rc7+ #7
task: ffff88003bd0df40 task.stack: ffff8800375b4000
RIP: 0010: kthread_stop+0x52/0x300
Call Trace:
crypt_dtr+0x77/0x120
dm_table_destroy+0x6f/0x120
__dm_destroy+0x130/0x250
dm_destroy+0x13/0x20
dev_remove+0xe6/0x120
? dev_suspend+0x250/0x250
ctl_ioctl+0x1fc/0x530
? __lock_acquire+0x24f/0x1b10
dm_ctl_ioctl+0x13/0x20
do_vfs_ioctl+0x91/0x6a0
? ____fput+0xe/0x10
? entry_SYSCALL_64_fastpath+0x5/0xbd
? trace_hardirqs_on_caller+0x151/0x1e0
SyS_ioctl+0x41/0x70
entry_SYSCALL_64_fastpath+0x1f/0xbd
This problem was introduced by bcbd94ff48 ("dm crypt: fix a possible
hang due to race condition on exit").
Looking at the description of that patch (excerpted below), it seems
like the problem it addresses can be solved by just using
set_current_state instead of __set_current_state, since we obviously
need the memory barrier.
| dm crypt: fix a possible hang due to race condition on exit
|
| A kernel thread executes __set_current_state(TASK_INTERRUPTIBLE),
| __add_wait_queue, spin_unlock_irq and then tests kthread_should_stop().
| It is possible that the processor reorders memory accesses so that
| kthread_should_stop() is executed before __set_current_state(). If
| such reordering happens, there is a possible race on thread
| termination: [...]
So this patch just reverts the aforementioned patch and changes the
__set_current_state(TASK_INTERRUPTIBLE) to set_current_state(...). This
fixes the crash and should also fix the potential hang.
Fixes: bcbd94ff48 ("dm crypt: fix a possible hang due to race condition on exit")
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This change offers a pretty significant performance improvement.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
More efficient way to iterate an array due to prefetching (makes use of
the new dm_btree_cursor_* api).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This uses prefetching to speed up iteration through a btree.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
For smq the 32 bit 'hint' stores the multiqueue level that the entry
should be stored in. If a different policy has been used previously,
and then switched to smq, the hints will be invalid. In which case we
used to put all entries in the bottom level of the multiqueue, and then
redistribute. Redistribution is faster if we put entries with invalid
hints in random levels initially.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
It's far quicker to always delete the hint array and recreate with
dm_array_new() because we avoid the copying caused by mutation.
Also simplifies the policy interface, replacing the walk_hints() with
the simpler get_hint().
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm_array_new() creates a new, populated array more efficiently than
starting with an empty one and resizing.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
bio_free_pages is introduced in commit 1dfa0f68c0
("block: add a helper to free bio bounce buffer pages"),
we can reuse the func in other modules after it was
imported.
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Acked-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
register_shrinker() now can fail. When it happens, shrinker.nr_deferred is
null. We use it to determine if unregister_shrinker is required.
Signed-off-by: Shaohua Li <shli@fb.com>
register_shrinker can fail after commit 1d3d4437ea ("vmscan: per-node
deferred work"), we should detect the failure of it, otherwise we may
fail to register shrinker after raid5 configuration was setup successfully.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Shaohua Li <shli@fb.com>
if bitmap_create fails, the bitmap is already cleaned up and the returned value
is an error number. We can't do the cleanup again.
Reported-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Shaohua Li <shli@fb.com>
raid5 will split bio to proper size internally, there is no point to use
underlayer disk's max_hw_sectors. In my qemu system, without the change,
the raid5 only receives 128k size bio, which reduces the chance of bio
merge sending to underlayer disks.
Signed-off-by: Shaohua Li <shli@fb.com>
When one node is perform resync or recovery, other nodes
can't get resync lock and could block for a while before
it holds the lock, so we can't stop array immediately for
this scenario.
To make array could be stop quickly, we check MD_CLOSING
in dlm_lock_sync_interruptible to make us can interrupt
the lock request.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
When some node leaves cluster, then it's bitmap need to be
synced by another node, so "md*_recover" thread is triggered
for the purpose. However, with below steps. we can find tasks
hang happened either in B or C.
1. Node A create a resyncing cluster raid1, assemble it in
other two nodes (B and C).
2. stop array in B and C.
3. stop array in A.
linux44:~ # ps aux|grep md|grep D
root 5938 0.0 0.1 19852 1964 pts/0 D+ 14:52 0:00 mdadm -S md0
root 5939 0.0 0.0 0 0 ? D 14:52 0:00 [md0_recover]
linux44:~ # cat /proc/5939/stack
[<ffffffffa04cf321>] dlm_lock_sync+0x71/0x90 [md_cluster]
[<ffffffffa04d0705>] recover_bitmaps+0x125/0x220 [md_cluster]
[<ffffffffa052105d>] md_thread+0x16d/0x180 [md_mod]
[<ffffffff8107ad94>] kthread+0xb4/0xc0
[<ffffffff8152a518>] ret_from_fork+0x58/0x90
linux44:~ # cat /proc/5938/stack
[<ffffffff8107afde>] kthread_stop+0x6e/0x120
[<ffffffffa0519da0>] md_unregister_thread+0x40/0x80 [md_mod]
[<ffffffffa04cfd20>] leave+0x70/0x120 [md_cluster]
[<ffffffffa0525e24>] md_cluster_stop+0x14/0x30 [md_mod]
[<ffffffffa05269ab>] bitmap_free+0x14b/0x150 [md_mod]
[<ffffffffa0523f3b>] do_md_stop+0x35b/0x5a0 [md_mod]
[<ffffffffa0524e83>] md_ioctl+0x873/0x1590 [md_mod]
[<ffffffff81288464>] blkdev_ioctl+0x214/0x7d0
[<ffffffff811dd3dd>] block_ioctl+0x3d/0x40
[<ffffffff811b92d4>] do_vfs_ioctl+0x2d4/0x4b0
[<ffffffff811b9538>] SyS_ioctl+0x88/0xa0
[<ffffffff8152a5c9>] system_call_fastpath+0x16/0x1b
The problem is caused by recover_bitmaps can't reliably abort
when the thread is unregistered. So dlm_lock_sync_interruptible
is introduced to detect the thread's situation to fix the problem.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Previously, we used completion to sync between require dlm lock
and sync_ast, however we will have to expose completion.wait
and completion.done in dlm_lock_sync_interruptible (introduced
later), it is not a common usage for completion, so convert
related things to wait queue.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
We need to use rcu_read_lock/unlock to avoid potential
race.
Reported-by: Shaohua Li <shli@fb.com>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
cluster_info and bitmap_info.nodes also need to be
cleared when array is stopped.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
When stop clustered raid while it is pending on resync,
MD_STILL_CLOSED flag could be cleared since udev rule
is triggered to open the mddev. So obviously array can't
be stopped soon and returns EBUSY.
mdadm -Ss md-raid-arrays.rules
set MD_STILL_CLOSED md_open()
... ... ... clear MD_STILL_CLOSED
do_md_stop
We make below changes to resolve this issue:
1. rename MD_STILL_CLOSED to MD_CLOSING since it is set
when stop array and it means we are stopping array.
2. let md_open returns early if CLOSING is set, so no
other threads will open array if one thread is trying
to close it.
3. no need to clear CLOSING bit in md_open because 1 has
ensure the bit is cleared, then we also don't need to
test CLOSING bit in do_md_stop.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Since DLM_LKF_FORCEUNLOCK is used in lockres_free,
we don't need to call dlm_unlock_sync before free
lock resource.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
For dlm_unlock, we need to pass flag to dlm_unlock as the
third parameter instead of set res->flags.
Also, DLM_LKF_FORCEUNLOCK is more suitable for dlm_unlock
since it works even the lock is on waiting or convert queue.
Acked-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The new_disk_ack could return failure if WAITING_FOR_NEWDISK
is not set, so we need to kick the dev from array in case
failure happened.
And we missed to check err before call new_disk_ack othwise
we could kick a rdev which isn't in array, thanks for the
reminder from Shaohua.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Enable devices without a gendisk instance to register itself with blk-mq
and expose the associated multi-queue sysfs entries.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Return DM_MAPIO_DELAY_REQUEUE from .clone_and_map_rq. Also, return
false from .busy, if all paths are down, so that blk-mq requests get
mapped via .clone_and_map_rq -- which results in DM_MAPIO_DELAY_REQUEUE
being returned to dm-rq.
This change allows for a noticeable reduction in cpu utilization
(reduced kworker load) while all paths are down, e.g.:
system CPU idleness (as measured by fio's --idle-prof=system):
before: system: 86.58%
after: system: 98.60%
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
When reinstating a path the blk-mq request_queue's requeue_list should
get kicked. It makes sense to kick the requeue_list as part of the
existing hook (previously only used by bio-based support).
Rename process_queued_bios_list to process_queued_io_list.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Make it possible for a request-based target to kick the DM device's
blk-mq request_queue's requeue_list.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
All drivers use the default, so provide an inline version of it. If we
ever need other queue mapping we can add an optional method back,
although supporting will also require major changes to the queue setup
code.
This provides better code generation, and better debugability as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Otherwise blk-mq will immediately dispatch requests that are requeued
via a BLK_MQ_RQ_QUEUE_BUSY return from blk_mq_ops .queue_rq.
Delayed requeue is implemented using blk_mq_delay_kick_requeue_list()
with a delay of 5 secs. In the context of DM multipath (all paths down)
it doesn't make any sense to requeue more quickly.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use autoremove_wake_function() instead of default_wake_function()
to make the dm wait loops more similar to other wait loops in the
kernel. This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use signal_pending_state() instead of open-coding it. This patch does
not change any functionality but makes it possible to pass TASK_KILLABLE
as the second argument of dm_wait_for_completion(). See also commit
16882c1e96 ("sched: fix TASK_WAKEKILL vs SIGKILL race").
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Rename 'interruptible' into 'task_state' to make it clear that this
argument is a task state instead of a boolean. Also, change type from
int to long.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Document the locking assumptions for the __bind() and __dm_suspend()
functions.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Shaohua Li