Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rework of the core hotplug code triggers the WARN_ON in start_wd_cpu()
on powerpc because it is called multiple times for the boot CPU.
The first call is via:
start_wd_on_cpu+0x80/0x2f0
watchdog_nmi_reconfigure+0x124/0x170
softlockup_reconfigure_threads+0x110/0x130
lockup_detector_init+0xbc/0xe0
kernel_init_freeable+0x18c/0x37c
kernel_init+0x2c/0x160
ret_from_kernel_thread+0x5c/0xbc
And then again via the CPU hotplug registration:
start_wd_on_cpu+0x80/0x2f0
cpuhp_invoke_callback+0x194/0x620
cpuhp_thread_fun+0x7c/0x1b0
smpboot_thread_fn+0x290/0x2a0
kthread+0x168/0x1b0
ret_from_kernel_thread+0x5c/0xbc
This can be avoided by setting up the cpu hotplug state with nocalls and
move the initialization to the watchdog_nmi_probe() function. That
initializes the hotplug callbacks without invoking the callback and the
following core initialization function then configures the watchdog for the
online CPUs (in this case CPU0) via softlockup_reconfigure_threads().
Reported-and-tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
The recent cleanup of the watchdog code split watchdog_nmi_reconfigure()
into two stages. One to stop the NMI and one to restart it after
reconfiguration. That was done by adding a boolean 'run' argument to the
code, which is functionally correct but not necessarily a piece of art.
Replace it by two explicit functions: watchdog_nmi_stop() and
watchdog_nmi_start().
Fixes: 6592ad2fcc ("watchdog/core, powerpc: Make watchdog_nmi_reconfigure() two stage")
Requested-by: Linus 'Nursing his pet-peeve' Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Thomas 'Mopping up garbage' Gleixner <tglx@linutronix.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1710021957480.2114@nanos
watchdog_nmi_enable() is an unparseable mess, Provide a clean perf specific
implementation, which will be used when the existing setup/teardown mess is
replaced.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Link: http://lkml.kernel.org/r/20170912194148.180215498@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The watchdog tries to create perf events even after it figured out that
perf is not functional or the requested event is not supported.
That's braindead as this can be done once at init time and if not supported
the NMI watchdog can be turned off unconditonally.
Implement the perf hardlockup detector functionality for that. This creates
a new event create function, which will replace the unholy mess of the
existing one in later patches.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Link: http://lkml.kernel.org/r/20170912194148.019090547@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Both the perf reconfiguration and the powerpc watchdog_nmi_reconfigure()
need to be done in two steps.
1) Stop all NMIs
2) Read the new parameters and start NMIs
Right now watchdog_nmi_reconfigure() is a combination of both. To allow a
clean reconfiguration add a 'run' argument and split the functionality in
powerpc.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/20170912194147.862865570@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reflect that these variables are user interface related and remove the
whitespace damage in the sysctl table while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Link: http://lkml.kernel.org/r/20170912194147.783210221@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The sysctl of the nmi_watchdog file prevents writes by setting:
min = max = 0
if none of the users is enabled. That involves ifdeffery and is competely
non obvious.
If none of the facilities is enabeld, then the file can simply be made read
only. Move the ifdeffery into the header and use a constant for file
permissions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Link: http://lkml.kernel.org/r/20170912194147.706073616@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Having the same #ifdef in various places does not make it more
readable. Collect stuff into one place.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Link: http://lkml.kernel.org/r/20170912194147.627096864@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit:
b94f51183b ("kernel/watchdog: prevent false hardlockup on overloaded system")
tries to fix the following issue:
proc_write()
set_sample_period() <--- New sample period becoms visible
<----- Broken starts
proc_watchdog_update()
watchdog_enable_all_cpus() watchdog_hrtimer_fn()
update_watchdog_all_cpus() restart_timer(sample_period)
watchdog_park_threads()
thread->park()
disable_nmi()
<----- Broken ends
The reason why this is broken is that the update of the watchdog threshold
becomes immediately effective and visible for the hrtimer function which
uses that value to rearm the timer. But the NMI/perf side still uses the
old value up to the point where it is disabled. If the rate has been
lowered then the NMI can run fast enough to 'detect' a hard lockup because
the timer has not fired due to the longer period.
The patch 'fixed' this by adding a variable:
proc_write()
set_sample_period()
<----- Broken starts
proc_watchdog_update()
watchdog_enable_all_cpus() watchdog_hrtimer_fn()
update_watchdog_all_cpus() restart_timer(sample_period)
watchdog_park_threads()
park_in_progress = 1
<----- Broken ends
nmi_watchdog()
if (park_in_progress)
return;
The only effect of this variable was to make the window where the breakage
can hit small enough that it was not longer observable in testing. From a
correctness point of view it is a pointless bandaid which merily papers
over the root cause: the unsychronized update of the variable.
Looking deeper into the related code pathes unearthed similar problems in
the watchdog_start()/stop() functions.
watchdog_start()
perf_nmi_event_start()
hrtimer_start()
watchdog_stop()
hrtimer_cancel()
perf_nmi_event_stop()
In both cases the call order is wrong because if the tasks gets preempted
or the VM gets scheduled out long enough after the first call, then there is
a chance that the next NMI will see a stale hrtimer interrupt count and
trigger a false positive hard lockup splat.
Get rid of park_in_progress so the code can be gradually deobfuscated and
pruned from several layers of duct tape papering over the root cause,
which has been either ignored or not understood at all.
Once this is removed the underlying problem will be fixed by rewriting the
proc interface to do a proper synchronized update.
Address the start/stop() ordering problem as well by reverting the call
order, so this part is at least correct now.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1709052038270.2393@nanos
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The following deadlock is possible in the watchdog hotplug code:
cpus_write_lock()
...
takedown_cpu()
smpboot_park_threads()
smpboot_park_thread()
kthread_park()
->park() := watchdog_disable()
watchdog_nmi_disable()
perf_event_release_kernel();
put_event()
_free_event()
->destroy() := hw_perf_event_destroy()
x86_release_hardware()
release_ds_buffers()
get_online_cpus()
when a per cpu watchdog perf event is destroyed which drops the last
reference to the PMU hardware. The cleanup code there invokes
get_online_cpus() which instantly deadlocks because the hotplug percpu
rwsem is write locked.
To solve this add a deferring mechanism:
cpus_write_lock()
kthread_park()
watchdog_nmi_disable(deferred)
perf_event_disable(event);
move_event_to_deferred(event);
....
cpus_write_unlock()
cleaup_deferred_events()
perf_event_release_kernel()
This is still properly serialized against concurrent hotplug via the
cpu_add_remove_lock, which is held by the task which initiated the hotplug
event.
This is also used to handle event destruction when the watchdog threads are
parked via other mechanisms than CPU hotplug.
Analyzed-by: Peter Zijlstra <peterz@infradead.org>
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Link: http://lkml.kernel.org/r/20170912194146.884469246@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This interface has several issues:
- It's causing recursive locking of the hotplug lock.
- It's complete overkill to teardown all threads and then recreate them
The same can be achieved with the simple hardlockup_detector_perf_stop /
restart() interfaces. The abuse from the busy looping poweroff() loop of
PARISC has been solved as well.
Remove the cruft.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Link: http://lkml.kernel.org/r/20170912194146.487537732@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
PARISC has a a busy looping power off routine. If the watchdog is enabled
the watchdog timer will still fire, but the thread is not running, which
causes the softlockup watchdog to trigger.
Provide a interface which allows to turn the watchdog off.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Cc: linux-parisc@vger.kernel.org
Link: http://lkml.kernel.org/r/20170912194146.327343752@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Provide an interface to stop and restart perf NMI watchdog events on all
CPUs. This is only usable during init and especially for handling the perf
HT bug on Intel machines. It's safe to use it this way as nothing can
start/stop the NMI watchdog in parallel.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Link: http://lkml.kernel.org/r/20170912194146.167649596@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The hardlockup detector on x86 uses a performance counter based on unhalted
CPU cycles and a periodic hrtimer. The hrtimer period is about 2/5 of the
performance counter period, so the hrtimer should fire 2-3 times before the
performance counter NMI fires. The NMI code checks whether the hrtimer
fired since the last invocation. If not, it assumess a hard lockup.
The calculation of those periods is based on the nominal CPU
frequency. Turbo modes increase the CPU clock frequency and therefore
shorten the period of the perf/NMI watchdog. With extreme Turbo-modes (3x
nominal frequency) the perf/NMI period is shorter than the hrtimer period
which leads to false positives.
A simple fix would be to shorten the hrtimer period, but that comes with
the side effect of more frequent hrtimer and softlockup thread wakeups,
which is not desired.
Implement a low pass filter, which checks the perf/NMI period against
kernel time. If the perf/NMI fires before 4/5 of the watchdog period has
elapsed then the event is ignored and postponed to the next perf/NMI.
That solves the problem and avoids the overhead of shorter hrtimer periods
and more frequent softlockup thread wakeups.
Fixes: 58687acba5 ("lockup_detector: Combine nmi_watchdog and softlockup detector")
Reported-and-tested-by: Kan Liang <Kan.liang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: dzickus@redhat.com
Cc: prarit@redhat.com
Cc: ak@linux.intel.com
Cc: babu.moger@oracle.com
Cc: peterz@infradead.org
Cc: eranian@google.com
Cc: acme@redhat.com
Cc: stable@vger.kernel.org
Cc: atomlin@redhat.com
Cc: akpm@linux-foundation.org
Cc: torvalds@linux-foundation.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1708150931310.1886@nanos
Split SOFTLOCKUP_DETECTOR from LOCKUP_DETECTOR, and split
HARDLOCKUP_DETECTOR_PERF from HARDLOCKUP_DETECTOR.
LOCKUP_DETECTOR implies the general boot, sysctl, and programming
interfaces for the lockup detectors.
An architecture that wants to use a hard lockup detector must define
HAVE_HARDLOCKUP_DETECTOR_PERF or HAVE_HARDLOCKUP_DETECTOR_ARCH.
Alternatively an arch can define HAVE_NMI_WATCHDOG, which provides the
minimum arch_touch_nmi_watchdog, and it otherwise does its own thing and
does not implement the LOCKUP_DETECTOR interfaces.
sparc is unusual in that it has started to implement some of the
interfaces, but not fully yet. It should probably be converted to a full
HAVE_HARDLOCKUP_DETECTOR_ARCH.
[npiggin@gmail.com: fix]
Link: http://lkml.kernel.org/r/20170617223522.66c0ad88@roar.ozlabs.ibm.com
Link: http://lkml.kernel.org/r/20170616065715.18390-4-npiggin@gmail.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Reviewed-by: Babu Moger <babu.moger@oracle.com>
Tested-by: Babu Moger <babu.moger@oracle.com> [sparc]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For architectures that define HAVE_NMI_WATCHDOG, instead of having them
provide the complete touch_nmi_watchdog() function, just have them
provide arch_touch_nmi_watchdog().
This gives the generic code more flexibility in implementing this
function, and arch implementations don't miss out on touching the
softlockup watchdog or other generic details.
Link: http://lkml.kernel.org/r/20170616065715.18390-3-npiggin@gmail.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Reviewed-by: Babu Moger <babu.moger@oracle.com>
Tested-by: Babu Moger <babu.moger@oracle.com> [sparc]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "Improve watchdog config for arch watchdogs", v4.
A series to make the hardlockup watchdog more easily replaceable by arch
code. The last patch provides some justification for why we want to do
this (existing sparc watchdog is another that could benefit).
This patch (of 5):
Remove unused declaration.
Link: http://lkml.kernel.org/r/20170616065715.18390-2-npiggin@gmail.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Reviewed-by: Babu Moger <babu.moger@oracle.com>
Tested-by: Babu Moger <babu.moger@oracle.com> [sparc]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These methods don't belong into <linux/sched.h>, they are neither directly
related to task_struct or are scheduler functionality.
Put them next to the other watchdog methods in <linux/nmi.h>.
( Arguably that header's name is a misnomer, and this patch makes it
more so - but it should be renamed in another patch. )
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On an overloaded system, it is possible that a change in the watchdog
threshold can be delayed long enough to trigger a false positive.
This can easily be achieved by having a cpu spinning indefinitely on a
task, while another cpu updates watchdog threshold.
What happens is while trying to park the watchdog threads, the hrtimers
on the other cpus trigger and reprogram themselves with the new slower
watchdog threshold. Meanwhile, the nmi watchdog is still programmed
with the old faster threshold.
Because the one cpu is blocked, it prevents the thread parking on the
other cpus from completing, which is needed to shutdown the nmi watchdog
and reprogram it correctly. As a result, a false positive from the nmi
watchdog is reported.
Fix this by setting a park_in_progress flag to block all lockups until
the parking is complete.
Fix provided by Ulrich Obergfell.
[akpm@linux-foundation.org: s/park_in_progress/watchdog_park_in_progress/]
Link: http://lkml.kernel.org/r/1481041033-192236-1-git-send-email-dzickus@redhat.com
Signed-off-by: Don Zickus <dzickus@redhat.com>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "Clean up watchdog handlers", v2.
This is an attempt to cleanup watchdog handlers. Right now,
kernel/watchdog.c implements both softlockup and hardlockup detectors.
Softlockup code is generic. Hardlockup code is arch specific. Some
architectures don't use hardlockup detectors. They use their own
watchdog detectors. To make both these combination work, we have
numerous #ifdefs in kernel/watchdog.c.
We are trying here to make these handlers independent of each other.
Also provide an interface for architectures to implement their own
handlers. watchdog_nmi_enable and watchdog_nmi_disable will be defined
as weak such that architectures can override its definitions.
Thanks to Don Zickus for his suggestions.
Here are our previous discussions
http://www.spinics.net/lists/sparclinux/msg16543.htmlhttp://www.spinics.net/lists/sparclinux/msg16441.html
This patch (of 3):
Move shared macros and definitions to nmi.h so that watchdog.c, new file
watchdog_hld.c or any other architecture specific handler can use those
definitions.
Link: http://lkml.kernel.org/r/1478034826-43888-2-git-send-email-babu.moger@oracle.com
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Yaowei Bai <baiyaowei@cmss.chinamobile.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: Josh Hunt <johunt@akamai.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "improvements to the nmi_backtrace code" v9.
This patch series modifies the trigger_xxx_backtrace() NMI-based remote
backtracing code to make it more flexible, and makes a few small
improvements along the way.
The motivation comes from the task isolation code, where there are
scenarios where we want to be able to diagnose a case where some cpu is
about to interrupt a task-isolated cpu. It can be helpful to see both
where the interrupting cpu is, and also an approximation of where the
cpu that is being interrupted is. The nmi_backtrace framework allows us
to discover the stack of the interrupted cpu.
I've tested that the change works as desired on tile, and build-tested
x86, arm, mips, and sparc64. For x86 I confirmed that the generic
cpuidle stuff as well as the architecture-specific routines are in the
new cpuidle section. For arm, mips, and sparc I just build-tested it
and made sure the generic cpuidle routines were in the new cpuidle
section, but I didn't attempt to figure out which the platform-specific
idle routines might be. That might be more usefully done by someone
with platform experience in follow-up patches.
This patch (of 4):
Currently you can only request a backtrace of either all cpus, or all
cpus but yourself. It can also be helpful to request a remote backtrace
of a single cpu, and since we want that, the logical extension is to
support a cpumask as the underlying primitive.
This change modifies the existing lib/nmi_backtrace.c code to take a
cpumask as its basic primitive, and modifies the linux/nmi.h code to use
the new "cpumask" method instead.
The existing clients of nmi_backtrace (arm and x86) are converted to
using the new cpumask approach in this change.
The other users of the backtracing API (sparc64 and mips) are converted
to use the cpumask approach rather than the all/allbutself approach.
The mips code ignored the "include_self" boolean but with this change it
will now also dump a local backtrace if requested.
Link: http://lkml.kernel.org/r/1472487169-14923-2-git-send-email-cmetcalf@mellanox.com
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org> [arm]
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 10f9014912 ("x86: Cleanup hw_nmi.c cruft") removed unused
code in the hw_nmi.c file because of the redesign of the hardlockup
watchdog but left declaration of hw_nmi_is_cpu_stuck in linux/nmi.h,
so remvoe it.
Signed-off-by: Yaowei Bai <baiyaowei@cmss.chinamobile.com>
Link: http://lkml.kernel.org/r/1458697210-3027-1-git-send-email-baiyaowei@cmss.chinamobile.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In many cases of hardlockup reports, it's actually not possible to know
why it triggered, because the CPU that got stuck is usually waiting on a
resource (with IRQs disabled) in posession of some other CPU is holding.
IOW, we are often looking at the stacktrace of the victim and not the
actual offender.
Introduce sysctl / cmdline parameter that makes it possible to have
hardlockup detector perform all-CPU backtrace.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull NMI backtrace update from Russell King:
"These changes convert the x86 NMI handling to be a library
implementation which other architectures can make use of. Thomas
Gleixner has reviewed and tested these changes, and wishes me to send
these rather than taking them through the tip tree.
The final patch in the set adds an initial implementation using this
infrastructure to ARM, even though it doesn't send the IPI at "NMI"
level. Patches are in progress to add the ARM equivalent of NMI, but
we still need the IRQ-level fallback for systems where the "NMI" isn't
available due to secure firmware denying access to it"
* 'nmi' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: add basic support for on-demand backtrace of other CPUs
nmi: x86: convert to generic nmi handler
nmi: create generic NMI backtrace implementation
Rename watchdog_suspend() to lockup_detector_suspend() and
watchdog_resume() to lockup_detector_resume() to avoid confusion with the
watchdog subsystem and to be consistent with the existing name
lockup_detector_init().
Also provide comment blocks to explain the watchdog_running and
watchdog_suspended variables and their relationship.
Signed-off-by: Ulrich Obergfell <uobergfe@redhat.com>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Stephane Eranian <eranian@google.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove watchdog_nmi_disable_all() and watchdog_nmi_enable_all() since
these functions are no longer needed. If a subsystem has a need to
deactivate the watchdog temporarily, it should utilize the
watchdog_suspend() and watchdog_resume() functions.
[akpm@linux-foundation.org: fix build with CONFIG_LOCKUP_DETECTOR=m]
Signed-off-by: Ulrich Obergfell <uobergfe@redhat.com>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Stephane Eranian <eranian@google.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This interface can be utilized to deactivate the hard and soft lockup
detector temporarily. Callers are expected to minimize the duration of
deactivation. Multiple deactivations are allowed to occur in parallel but
should be rare in practice.
[akpm@linux-foundation.org: remove unneeded static initialization]
Signed-off-by: Ulrich Obergfell <uobergfe@redhat.com>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Stephane Eranian <eranian@google.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kernel's NMI watchdog has nothing to do with the watchdog subsystem.
Its header declarations should be in linux/nmi.h, not linux/watchdog.h.
The code provided two sets of dummy functions if HARDLOCKUP_DETECTOR is
not configured, one in the include file and one in kernel/watchdog.c.
Remove the dummy functions from kernel/watchdog.c and use those from the
include file.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Stephane Eranian <eranian@google.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86s NMI backtrace implementation (for arch_trigger_all_cpu_backtrace())
is fairly generic in nature - the only architecture specific bits are
the act of raising the NMI to other CPUs, and reporting the status of
the NMI handler.
These are fairly simple to factor out, and produce a generic
implementation which can be shared between ARM and x86.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change the default behavior of watchdog so it only runs on the
housekeeping cores when nohz_full is enabled at build and boot time.
Allow modifying the set of cores the watchdog is currently running on
with a new kernel.watchdog_cpumask sysctl.
In the current system, the watchdog subsystem runs a periodic timer that
schedules the watchdog kthread to run. However, nohz_full cores are
designed to allow userspace application code running on those cores to
have 100% access to the CPU. So the watchdog system prevents the
nohz_full application code from being able to run the way it wants to,
thus the motivation to suppress the watchdog on nohz_full cores, which
this patchset provides by default.
However, if we disable the watchdog globally, then the housekeeping
cores can't benefit from the watchdog functionality. So we allow
disabling it only on some cores. See Documentation/lockup-watchdogs.txt
for more information.
[jhubbard@nvidia.com: fix a watchdog crash in some configurations]
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Have kvm_guest_init() use hardlockup_detector_disable() instead of
watchdog_enable_hardlockup_detector(false).
Remove the watchdog_hardlockup_detector_is_enabled() and the
watchdog_enable_hardlockup_detector() function which are no longer needed.
Signed-off-by: Ulrich Obergfell <uobergfe@redhat.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the current user interface of the watchdog mechanism it is only
possible to disable or enable both lockup detectors at the same time.
This series introduces new kernel parameters and changes the semantics of
some existing kernel parameters, so that the hard lockup detector and the
soft lockup detector can be disabled or enabled individually. With this
series applied, the user interface is as follows.
- parameters in /proc/sys/kernel
. soft_watchdog
This is a new parameter to control and examine the run state of
the soft lockup detector.
. nmi_watchdog
The semantics of this parameter have changed. It can now be used
to control and examine the run state of the hard lockup detector.
. watchdog
This parameter is still available to control the run state of both
lockup detectors at the same time. If this parameter is examined,
it shows the logical OR of soft_watchdog and nmi_watchdog.
. watchdog_thresh
The semantics of this parameter are not affected by the patch.
- kernel command line parameters
. nosoftlockup
The semantics of this parameter have changed. It can now be used
to disable the soft lockup detector at boot time.
. nmi_watchdog=0 or nmi_watchdog=1
Disable or enable the hard lockup detector at boot time. The patch
introduces '=1' as a new option.
. nowatchdog
The semantics of this parameter are not affected by the patch. It
is still available to disable both lockup detectors at boot time.
Also, remove the proc_dowatchdog() function which is no longer needed.
[dzickus@redhat.com: wrote changelog]
[dzickus@redhat.com: update documentation for kernel params and sysctl]
Signed-off-by: Ulrich Obergfell <uobergfe@redhat.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Separate handlers for each watchdog parameter in /proc/sys/kernel replace
the proc_dowatchdog() function. Three of those handlers merely call
proc_watchdog_common() with one different argument.
Signed-off-by: Ulrich Obergfell <uobergfe@redhat.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The hardlockup and softockup had always been tied together. Due to the
request of KVM folks, they had a need to have one enabled but not the
other. Internally rework the code to split things apart more cleanly.
There is a bunch of churn here, but the end result should be code that
should be easier to maintain and fix without knowing the internals of what
is going on.
This patch (of 9):
Introduce new definitions and variables to separate the user interface in
/proc/sys/kernel from the internal run state of the lockup detectors. The
internal run state is represented by two bits in a new variable that is
named 'watchdog_enabled'. This helps simplify the code, for example:
- In order to check if any of the two lockup detectors is enabled,
it is sufficient to check if 'watchdog_enabled' is not zero.
- In order to enable/disable one or both lockup detectors,
it is sufficient to set/clear one or both bits in 'watchdog_enabled'.
- Concurrent updates of 'watchdog_enabled' need not be synchronized via
a spinlock or a mutex. Updates can either be atomic or concurrency can
be detected by using 'cmpxchg'.
Signed-off-by: Ulrich Obergfell <uobergfe@redhat.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some cases we don't want hard lockup detection enabled by default.
An example is when running as a guest. Introduce
watchdog_enable_hardlockup_detector(bool)
allowing those cases to disable hard lockup detection. This must be
executed early by the boot processor from e.g. smp_prepare_boot_cpu, in
order to allow kernel command line arguments to override it, as well as
to avoid hard lockup detection being enabled before we've had a chance
to indicate that it's unwanted. In summary,
initial boot: default=enabled
smp_prepare_boot_cpu
watchdog_enable_hardlockup_detector(false): default=disabled
cmdline has 'nmi_watchdog=1': default=enabled
The running kernel still has the ability to enable/disable at any time
with /proc/sys/kernel/nmi_watchdog us usual. However even when the
default has been overridden /proc/sys/kernel/nmi_watchdog will initially
show '1'. To truly turn it on one must disable/enable it, i.e.
echo 0 > /proc/sys/kernel/nmi_watchdog
echo 1 > /proc/sys/kernel/nmi_watchdog
This patch will be immediately useful for KVM with the next patch of this
series. Other hypervisor guest types may find it useful as well.
[akpm@linux-foundation.org: fix build]
[dzickus@redhat.com: fix compile issues on sparc]
Signed-off-by: Ulrich Obergfell <uobergfe@redhat.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently APEI depends on x86 architecture. It is because of NMI hardware
error notification of GHES which is currently supported by x86 only.
However, many other APEI features can be still used perfectly by other
architectures.
This commit adds two symbols:
1. HAVE_ACPI_APEI for those archs which support APEI.
2. HAVE_ACPI_APEI_NMI which is used for NMI code isolation in ghes.c
file. NMI related data and functions are grouped so they can be wrapped
inside one #ifdef section. Appropriate function stubs are provided for
!NMI case.
Note there is no functional changes for x86 due to hard selected
HAVE_ACPI_APEI and HAVE_ACPI_APEI_NMI symbols.
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
A 'softlockup' is defined as a bug that causes the kernel to loop in
kernel mode for more than a predefined period to time, without giving
other tasks a chance to run.
Currently, upon detection of this condition by the per-cpu watchdog
task, debug information (including a stack trace) is sent to the system
log.
On some occasions, we have observed that the "victim" rather than the
actual "culprit" (i.e. the owner/holder of the contended resource) is
reported to the user. Often this information has proven to be
insufficient to assist debugging efforts.
To avoid loss of useful debug information, for architectures which
support NMI, this patch makes it possible to improve soft lockup
reporting. This is accomplished by issuing an NMI to each cpu to obtain
a stack trace.
If NMI is not supported we just revert back to the old method. A sysctl
and boot-time parameter is available to toggle this feature.
[dzickus@redhat.com: add CONFIG_SMP in certain areas]
[akpm@linux-foundation.org: additional CONFIG_SMP=n optimisations]
[mq@suse.cz: fix warning]
Signed-off-by: Aaron Tomlin <atomlin@redhat.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Mateusz Guzik <mguzik@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Jan Moskyto Matejka <mq@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sometimes it is preferred not to use the trigger_all_cpu_backtrace()
routine when one wants to avoid capturing a back trace for current. For
instance if one was previously captured recently.
This patch provides a new routine namely
trigger_allbutself_cpu_backtrace() which offers the flexibility to issue
an NMI to every cpu but current and capture a back trace accordingly.
Patch x86 and sparc to support new routine.
[dzickus@redhat.com: add stub in #else clause]
[dzickus@redhat.com: don't print message in single processor case, wrap with get/put_cpu based on Oleg's suggestion]
[sfr@canb.auug.org.au: undo C99ism]
Signed-off-by: Aaron Tomlin <atomlin@redhat.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Mateusz Guzik <mguzik@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have two very conflicting state variable names in the
watchdog:
* watchdog_enabled: This one reflects the user interface. It's
set to 1 by default and can be overriden with boot options
or sysctl/procfs interface.
* watchdog_disabled: This is the internal toggle state that
tells if watchdog threads, timers and NMI events are currently
running or not. This state mostly depends on the user settings.
It's a convenient state latch.
Now we really need to find clearer names because those
are just too confusing to encourage deep review.
watchdog_enabled now becomes watchdog_user_enabled to reflect
its purpose as an interface.
watchdog_disabled becomes watchdog_running to suggest its
role as a pure internal state.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Anish Singh <anish198519851985@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Don Zickus <dzickus@redhat.com>
ARCH_HAS_NMI_WATCHDOG is a macro defined by arch, but config
HARDLOCKUP_DETECTOR depends on it. This is wrong, ARCH_HAS_NMI_WATCHDOG
has to be a Kconfig config, and arch's need it should select it
explicitly.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: David Howells <dhowells@redhat.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before the conversion of the NMI watchdog to perf event, the
watchdog timeout was 5 seconds. Now it is 60 seconds. For my
particular application, netbooks, 5 seconds was a better
timeout. With a short timeout, we catch faults earlier and are
able to send back a panic. With a 60 second timeout, the user is
unlikely to wait and will instead hit the power button, causing
us to lose the panic info.
This change configures the NMI period to watchdog_thresh and
sets the softlockup_thresh to watchdog_thresh * 2. In addition,
watchdog_thresh was reduced to 10 seconds as suggested by Ingo
Molnar.
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Cc: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/1306127423-3347-4-git-send-email-msb@chromium.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <20110517071642.GF22305@elte.hu>
This restores the previous behavior of softlock_thresh.
Currently, setting watchdog_thresh to zero causes the watchdog
kthreads to consume a lot of CPU.
In addition, the logic of proc_dowatchdog_thresh and
proc_dowatchdog_enabled has been factored into proc_dowatchdog.
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Cc: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/1306127423-3347-3-git-send-email-msb@chromium.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <20110517071018.GE22305@elte.hu>
The x86 arch has shifted its use of the nmi_watchdog from a
local implementation to the global one provide by
kernel/watchdog.c. This shift has caused a whole bunch of
compile problems under different config options. I attempt to
simplify things with the patch below.
In order to simplify things, I had to come to terms with the
meaning of two terms ARCH_HAS_NMI_WATCHDOG and
CONFIG_HARDLOCKUP_DETECTOR. Basically they mean the same thing,
the former on a local level and the latter on a global level.
With the old x86 nmi watchdog gone, there is no need to rely on
defining the ARCH_HAS_NMI_WATCHDOG variable because it doesn't
make sense any more. x86 will now use the global
implementation.
The changes below do a few things. First it changes the few
places that relied on ARCH_HAS_NMI_WATCHDOG to use
CONFIG_X86_LOCAL_APIC (the former was an alias for the latter
anyway, so nothing unusual here). Those pieces of code were
relying more on local apic functionality the nmi watchdog
functionality, so the change should make sense.
Second, I removed the x86 implementation of
touch_nmi_watchdog(). It isn't need now, instead x86 will rely
on kernel/watchdog.c's implementation.
Third, I removed the #define ARCH_HAS_NMI_WATCHDOG itself from
x86. And tweaked the include/linux/nmi.h file to tell users to
look for an externally defined touch_nmi_watchdog in the case of
ARCH_HAS_NMI_WATCHDOG _or_ CONFIG_HARDLOCKUP_DETECTOR. This
changes removes some of the ugliness in that file.
Finally, I added a Kconfig dependency for
CONFIG_HARDLOCKUP_DETECTOR that said you can't have
ARCH_HAS_NMI_WATCHDOG _and_ CONFIG_HARDLOCKUP_DETECTOR. You can
only have one nmi_watchdog.
Tested with
ARCH=i386: allnoconfig, defconfig, allyesconfig, (various broken
configs) ARCH=x86_64: allnoconfig, defconfig, allyesconfig,
(various broken configs)
Hopefully, after this patch I won't get any more compile broken
emails. :-)
v3:
changed a couple of 'linux/nmi.h' -> 'asm/nmi.h' to pick-up correct function
prototypes when CONFIG_HARDLOCKUP_DETECTOR is not set.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: fweisbec@gmail.com
LKML-Reference: <1293044403-14117-1-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
My patch that removed the old x86 nmi watchdog broke other
arches. This change reverts a piece of that patch and puts the
change in the correct spot.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Reviewed-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: fweisbec@gmail.com
Cc: yinghai@kernel.org
LKML-Reference: <1291068437-5331-2-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that the bulk of the old nmi_watchdog is gone, remove all
the stub variables and hooks associated with it.
This touches lots of files mainly because of how the io_apic
nmi_watchdog was implemented. Now that the io_apic nmi_watchdog
is forever gone, remove all its fingers.
Most of this code was not being exercised by virtue of
nmi_watchdog != NMI_IO_APIC, so there shouldn't be anything to
risky here.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: fweisbec@gmail.com
Cc: gorcunov@openvz.org
LKML-Reference: <1289578944-28564-3-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that we have a new nmi_watchdog that is more generic and
sits on top of the perf subsystem, we really do not need the old
nmi_watchdog any more.
In addition, the old nmi_watchdog doesn't really work if you are
using the default clocksource, hpet. The old nmi_watchdog code
relied on local apic interrupts to determine if the cpu is still
alive. With hpet as the clocksource, these interrupts don't
increment any more and the old nmi_watchdog triggers false
postives.
This piece removes the old nmi_watchdog code and stubs out any
variables and functions calls. The stubs are the same ones used
by the new nmi_watchdog code, so it should be well tested.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: fweisbec@gmail.com
Cc: gorcunov@openvz.org
LKML-Reference: <1289578944-28564-2-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Combining the softlockup and hardlockup code causes watchdog.c
to build even without the hardlockup detection support.
So if an arch, that has the previous and the new nmi watchdog
implementations cohabiting, wants to know if the generic one
is in use, CONFIG_LOCKUP_DETECTOR is not a reliable check.
We need to use CONFIG_HARDLOCKUP_DETECTOR instead.
Fixes:
kernel/built-in.o: In function `touch_nmi_watchdog':
(.text+0x449bc): multiple definition of `touch_nmi_watchdog'
arch/sparc/kernel/built-in.o:(.text+0x11b28): first defined here
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
LKML-Reference: <20100514151121.GR15159@redhat.com>
[ use CONFIG_HARDLOCKUP_DETECTOR instead of CONFIG_PERF_EVENTS_NMI]
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
The new nmi_watchdog (which uses the perf event subsystem) is very
similar in structure to the softlockup detector. Using Ingo's
suggestion, I combined the two functionalities into one file:
kernel/watchdog.c.
Now both the nmi_watchdog (or hardlockup detector) and softlockup
detector sit on top of the perf event subsystem, which is run every
60 seconds or so to see if there are any lockups.
To detect hardlockups, cpus not responding to interrupts, I
implemented an hrtimer that runs 5 times for every perf event
overflow event. If that stops counting on a cpu, then the cpu is
most likely in trouble.
To detect softlockups, tasks not yielding to the scheduler, I used the
previous kthread idea that now gets kicked every time the hrtimer fires.
If the kthread isn't being scheduled neither is anyone else and the
warning is printed to the console.
I tested this on x86_64 and both the softlockup and hardlockup paths
work.
V2:
- cleaned up the Kconfig and softlockup combination
- surrounded hardlockup cases with #ifdef CONFIG_PERF_EVENTS_NMI
- seperated out the softlockup case from perf event subsystem
- re-arranged the enabling/disabling nmi watchdog from proc space
- added cpumasks for hardlockup failure cases
- removed fallback to soft events if no PMU exists for hard events
V3:
- comment cleanups
- drop support for older softlockup code
- per_cpu cleanups
- completely remove software clock base hardlockup detector
- use per_cpu masking on hard/soft lockup detection
- #ifdef cleanups
- rename config option NMI_WATCHDOG to LOCKUP_DETECTOR
- documentation additions
V4:
- documentation fixes
- convert per_cpu to __get_cpu_var
- powerpc compile fixes
V5:
- split apart warn flags for hard and soft lockups
TODO:
- figure out how to make an arch-agnostic clock2cycles call
(if possible) to feed into perf events as a sample period
[fweisbec: merged conflict patch]
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
LKML-Reference: <1273266711-18706-2-git-send-email-dzickus@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Greg Kroah-Hartman