This reverts commit ff773714dd.
A generic solution is needed to save and retore the LUT information.
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes cursor corruption in certain cases.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
I see the following error message in my kernel log from time to time:
radeon 0000:07:00.0: ffff88007c334000 reserve failed for wait
radeon 0000:07:00.0: ffff88007c334000 reserve failed for wait
After investigation, it turns out that there's nothing to be afraid of
and everything works as intended. So remove the spurious log message.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make TV standard and DFP table revisions debug only.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These bits are used for internal communication and should
be left enabled. This may fix s/r issues on some systems.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We should not allocate any object into unmappable vram if we
have no means to access them which on all GPU means having the
CP running and on newer GPU having the blit utility working.
This patch limit the vram allocation to visible vram until
we have acceleration up and running.
Note that it's more than unlikely that we run into any issue
related to that as when acceleration is not woring userspace
should allocate any object in vram beside front buffer which
should fit in visible vram.
V2 use real_vram_size as mc_vram_size could be bigger than
the actual amount of vram
[airlied: fixup r700_cp_stop case]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
since the handle references are all tied to a file_priv, and when it disappears
all the handle refs go with it.
The fbcon ones we'd only notice on unload, but the nouveau notifier one
would would happen on reboot.
nouveau: Reported-by: Marc Dionne <marc.c.dionne@gmail.com>
nouveau: Tested-by: Marc Dionne <marc.c.dionne@gmail.com>
i915 unload: Reported-by: Keith Packard <keithp@keithp.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-radeon-next' of ../drm-radeon-next:
drm/radeon/kms: add drm blit support for evergreen
drm/radeon: Modify radeon_pm_in_vbl to use radeon_get_crtc_scanoutpos()
drm/radeon: Add function for display scanout position query.
drm/radeon/kms: rework spread spectrum handling
drm/radeon/kms: remove new pll algo
drm/radeon/kms: remove some pll algo flags
drm/radeon/kms: prefer high post dividers in legacy pll algo
drm/radeon/kms: properly handle 40 bit MC addresses in the cursor code
drm/radeon: add properties to configure the width of the underscan borders
drm/radeon/kms/r6xx+: use new style fencing (v3)
drm/radeon/kms: enable writeback (v2)
drm/radeon/kms: clean up r6xx/r7xx blit init (v2)
* drm-kdb-next:
drm/nouveau/kms: Avoid a hang entering KDB with VT accel on.
radeon, kdb, kms: Save and restore the LUT on atomic KMS enter/exit
drm, kdb, kms: Add an enter argument to mode_set_base_atomic() API
drm/nouveau/kms: Implement KDB debug hooks for nouveau KMS.
drm/radeon/kms: Implement KDB debug hooks for radeon KMS.
[airlied - add fix for vmwgfx build]
* 'nouveau/for-airlied' of ../drm-nouveau-next: (93 commits)
drm/ttm: restructure to allow driver to plug in alternate memory manager
drm/ttm: introduce utility function to free an allocated memory node
drm/nouveau: fix thinkos in mem timing table recordlen check
drm/nouveau: parse voltage from perf 0x40 entires
drm/nouveau: don't use the default pll limits in table v2.1 on nv50+ cards
drm/nv50: Fix large 3D performance regression caused by the interchannel sync patches.
drm/nouveau: Synchronize buffer object moves in hardware.
drm/nouveau: Use semaphores to handle inter-channel sync in hardware.
drm/nouveau: Provide a means to have arbitrary work run on fence completion.
drm/nouveau: Minor refactoring/cleanup of the fence code.
drm/nouveau: Add a module option to force card POST.
drm/nv50: prevent (IB_PUT == IB_GET) for occurring unless idle
drm/nv0x-nv4x: Leave the 0x40 bit untouched when changing CRE_LCD.
drm/nv30-nv40: Fix postdivider mask when writing engine/memory PLLs.
drm/nouveau: Fix perf table parsing on BMP v5.25.
drm/nouveau: fix required mode bandwidth calculation for DP
drm/nouveau: fix typo in c2aa91afea5f7e7ae4530fabd37414a79c03328c
drm/nva3: split pm backend out from nv50
drm/nouveau: run perflvl and M table scripts on mem clock change
drm/nouveau: pass perflvl struct to clock_pre()
...
When changing VTs non-atomically the kernel works in conjunction with
the Xserver in user space and receives the LUT information from the
Xserver via a system call. When changing modes atomically for kdb,
this information must be saved and restored without disturbing user
space as if nothing ever happened.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: David Airlie <airlied@linux.ie>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some devices such as the radeon chips receive information from user
space which needs to be saved when executing an atomic mode set
operation, else the user space would have to be queried again for the
information.
This patch extends the mode_set_base_atomic() call to pass an argument
to indicate if this is an entry or an exit from an atomic kernel mode
set change. Individual drm drivers can properly save and restore
state accordingly.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: David Airlie <airlied@linux.ie>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch implements blit support for bo moves using
the 3D engine. It uses the same method as r6xx/r7xx:
- store the base state in an IB
- emit variable state and vertex buffers to do the blit
This allows the hw to move bos using the 3D engine and allows
full use of vram beyond the pci aperture size.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
radeon_pm_in_vbl() didn't report in vblank status accurately. Make
it a wrapper around radeon_get_crtc_scanoutpos() which corrects for
biases, so it reports accurately.
radeon_pm_in_vbl() will only report in_vbl if all active crtc's
are currently inside vblank.
agd5f: use rdev->num_crtc rather than hardcoding the crtc count
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
radeon_get_crtc_scanoutpos() returns the current horizontal
and vertical scanout position of a crtc. It also reports if
the display scanout is currently inside the vblank area.
hpos reports current horizontal pixel scanout position.
vpos reports the current scanned out line as a value >= 0
in active scanout. If the scanout is inside vblank area, it
reports a negative value, the number of scanlines until
end of vblank aka start of active scanout, e.g., -3 ==
"At most 3 scanlines until end of vblank".
This code is derived from radeon_pm_in_vbl(), tested on
R500 and R600.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch reworks spread spectrum handling to enable it
properly on lvds and DP/eDP links. It also fixes several
bugs in the old spread spectrum code.
- Use the ss recommended reference divider if available
when calculating the pll
- Use the proper ss command tables on pre-DCE3 asics
- Avoid reading past the end of the ss info tables
- Enable ss on evergreen asics (lvds, dp, tmds)
- Enable ss on DP/eDP links
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The recent changes to the old algo (prefer high post div)
coupled with the range and precision limitations of using
fixed point with the new algo make the new algo less
useful. So drop the new algo. This should work as well
or better than the old new/old combinations and simplifies
the code a lot.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=30218
among others.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These shouldn't be needed with the post div changes
in the last patch.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This allows for a more exact fitting on the physical
display. The new properties default to zero which corresponds to the
previous underscan border width[height] formula:
(display_width[display_width] >> 5) + 16.
Example to set a horizontal border width of 30 and a vertikal border
height of 22:
xrandr --output HDMI-0 --set underscan on --set "underscan hborder" 30 --set "underscan vborder" 22
Signed-off-by: Marius Gröger <marius.groeger@googlemail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On r6xx+ a newer fence mechanism was implemented to replace
the old wait_until plus scratch regs setup. A single EOP event
will flush the destination caches, write a fence value, and generate
an interrupt. This is the recommended fence mechanism on r6xx+ asics.
This requires my previous writeback patch.
v2: fix typo that enabled event fence checking on all asics
rather than just r6xx+.
v3: properly enable EOP interrupts
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=29972
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When writeback is enabled, the GPU shadows writes to certain
registers into a buffer in memory. The driver can then read
the values from the shadow rather than reading back from the
register across the bus. Writeback can be disabled by setting
the no_wb module param to 1.
On r6xx/r7xx/evergreen, the following registers are shadowed:
- CP scratch registers
- CP read pointer
- IH write pointer
On r1xx-rr5xx, the following registers are shadowed:
- CP scratch registers
- CP read pointer
v2:
- Combine wb patches for r6xx-evergreen and r1xx-r5xx
- Writeback is disabled on AGP boards since it tends to be
unreliable on AGP using the gart.
- Check radeon_wb_init return values properly.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Move common code to init function.
v2: make sure the bo is pinned after init as well.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Nouveau will need this on GeForce 8 and up to account for the GPU
reordering physical VRAM for some memory types.
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Acked-by: Thomas Hellström <thellstrom@vmware.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Existing core code/drivers call drm_mm_put_block on ttm_mem_reg.mm_node
directly. Future patches will modify TTM behaviour in such a way that
ttm_mem_reg.mm_node doesn't necessarily belong to drm_mm.
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Acked-by: Thomas Hellström <thellstrom@vmware.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There were lots of places being inconsistent since handle count
looked like a kref but it really wasn't.
Fix this my just making handle count an atomic on the object,
and have it increase the normal object kref.
Now i915/radeon/nouveau drivers can drop the normal reference on
userspace object creation, and have the handle hold it.
This patch fixes a memory leak or corruption on unload, because
the driver had no way of knowing if a handle had been actually
added for this object, and the fbcon object needed to know this
to clean itself up properly.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Board has no digital connectors
Reported-by: Andy Walls <awalls@md.metrocast.net>
Tested-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
encoder info was not printed properly on boards using the
DFP6 id.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix string interpreted as trigraph and typo.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The texture base address registers are in units of 256 bytes.
The original CS checker treated these offsets as bytes, so the
original check was wrong. I fixed the units in a patch during
the 2.6.36 cycle, but this ended up breaking some existing
userspace (probably due to a bug in either userspace texture allocation
or the drm texture mipmap checker). So for now, until we come
up with a better fix, just warn if the mipmap size it too large.
This will keep existing userspace working and it should be just
as safe as before when we were checking the wrong units. These
are GPU MC addresses, so if they fall outside of the VRAM or
GART apertures, they end up at the GPU default page, so this should
be safe from a security perspective.
v2: Just disable the warning. It just spams the log and there's
nothing the user can do about it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <glisse@freedesktop.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There has been periodic evidence that LVDS, on at least some
panels, prefers the dividers selected by the legacy pll algo.
This patch forces the use of the legacy pll algo on RV620
LVDS panels. The old behavior (new pll algo) can be selected
by setting the new_pll module parameter to 1.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=30029
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
v2: Julien Cristau pointed out that @nondestructive results in
double-negatives and confusion when trying to interpret the parameter,
so use @force instead. Much easier to type as well. ;-)
And fix the miscompilation of vmgfx reported by Sedat Dilek.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit fixes bogus CS rejection if it contains a sequence
of the following operations:
- Set the color buffer 0. track->cb[i].robj becomes non-NULL.
- Render.
- Set a larger zbuffer than the previously-set color buffer.
- Set a larger scissor area as well.
- Set the color channel mask to 0 to do depth-only rendering.
- Render. --> rejected, because track->cb[i].robj remained non-NULL,
therefore the conditional checking for the color channel mask and
friends is not performed, and the larger scissor area causes
the rejection.
This fixes bugs:
- https://bugs.freedesktop.org/show_bug.cgi?id=29762
- https://bugs.freedesktop.org/show_bug.cgi?id=28869
And maybe some others which seem to look the same.
If possible, this commit should go to stable as well.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
One subtest of mesa/demos/gltestperf takes 9 seconds to complete,
so to prevent an unnecessary gpu reset followed by a hardlock, I am
increasing the interval to 10 seconds after which a GPU is considered
in a locked-up state. This is on RV530. However, with a little slower GPU,
we would surpass the interval easily, so this is not a good fix
for gltestperf.
Nevertheless, this commit also fixes hardlocks in the applications which
render at speed of less than 1 frame per second, where the whole frame
consists of only one command stream. The game Tiny & Big is an example.
This bar is now lowered to 0.1 fps.
Now the question comes down to whether we should (often unsuccessfully)
reset the GPU at all? Once we have stable enough drivers, we won't have to.
Has the time come already?
If possible, this commit should go to stable as well.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch fixes rendering errors on some evergreen boards.
Hardcoding the backend map is not an optimal solution, but
a better fix is being worked on.
Similar to the fix for rv740
(6271901d82).
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=29986
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Destructive load-detection is very expensive and due to failings
elsewhere can trigger system wide stalls of up to 600ms. A simple
first step to correcting this is not to invoke such an expensive
and destructive load-detection operation automatically.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29536
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16265
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
caused by d65d65b175
need to update the radeon crtc priv native mode before using it.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=30049
v2: integrate v/h copy paste typo
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Jason Wessel