The configuration data provided by an MCFG entry, i.e., PCI segment and bus
range, may span multiple host bridges.
pci_mcfg_lookup() previously required an exact match of the host bridge
starting bus and the MCFG starting bus, which made the following
configuration fail:
MCFG region:
segment: 0
bus range: 0x00-0xff
host bridge
segment: 0
bus range: 0x20-0x4f
Relax the bus range check in pci_mcfg_lookup() so we can use any MCFG entry
that contains the required bus range, as we do in pci_mmconfig_lookup().
[bhelgaas: changelog]
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tomasz Nowicki <tn@semihalf.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
PCIe controllers in X-Gene SoCs are not ECAM compliant: software needs to
configure additional controller's register to address device at
bus:dev:function.
Add a quirk to discover controller MMIO register space and configure
controller registers to select and address the target secondary device.
The quirk will only be applied for X-Gene PCIe MCFG table with
OEM revison 1, 2, 3 or 4 (PCIe controller v1 and v2 on X-Gene SoCs).
Tested-by: Jon Masters <jcm@redhat.com>
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ThunderX pass1.x requires to emulate the EA headers for on-chip devices
hence it has to use custom pci_thunder_ecam_ops for accessing PCI config
space (pci-thunder-ecam.c). Add new entries to MCFG quirk array where it
can be applied while probing ACPI based PCI host controller.
ThunderX pass1.x is using the same way for accessing off-chip devices
(so-called PEM) as silicon pass-2.x so we need to add PEM quirk entries
too.
Quirk is considered for ThunderX silicon pass1.x only which is identified
via MCFG revision 2.
ThunderX pass 1.x requires the following accessors:
NUMA node 0 PCI segments 0- 3: pci_thunder_ecam_ops (MCFG quirk)
NUMA node 0 PCI segments 4- 9: thunder_pem_ecam_ops (MCFG quirk)
NUMA node 1 PCI segments 10-13: pci_thunder_ecam_ops (MCFG quirk)
NUMA node 1 PCI segments 14-19: thunder_pem_ecam_ops (MCFG quirk)
[bhelgaas: change Makefile/ifdefs so quirk doesn't depend on
CONFIG_PCI_HOST_THUNDER_ECAM]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ThunderX PCIe controller to off-chip devices (so-called PEM) is not fully
compliant with ECAM standard. It uses non-standard configuration space
accessors (see thunder_pem_ecam_ops) and custom configuration space
granulation (see bus_shift = 24). In order to access configuration space
and probe PEM as ACPI-based PCI host controller we need to add MCFG quirk
infrastructure. This involves:
1. A new thunder_pem_acpi_init() init function to locate PEM-specific
register ranges using ACPI.
2. Export PEM thunder_pem_ecam_ops structure so it is visible to MCFG quirk
code.
3. New quirk entries for each PEM segment. Each contains platform IDs,
mentioned thunder_pem_ecam_ops and CFG resources.
Quirk is considered for ThunderX silicon pass2.x only which is identified
via MCFG revision 1.
ThunderX pass 2.x requires the following accessors:
NUMA Node 0 PCI segments 0- 3: pci_generic_ecam_ops (ECAM-compliant)
NUMA Node 0 PCI segments 4- 9: thunder_pem_ecam_ops (MCFG quirk)
NUMA Node 1 PCI segments 10-13: pci_generic_ecam_ops (ECAM-compliant)
NUMA Node 1 PCI segments 14-19: thunder_pem_ecam_ops (MCFG quirk)
[bhelgaas: adapt to use acpi_get_rc_resources(), update Makefile/ifdefs so
quirk doesn't depend on CONFIG_PCI_HOST_THUNDER_PEM]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe controller in Hip05/Hip06/Hip07 SoCs is not completely
ECAM-compliant. It is non-ECAM only for the RC bus config space; for any
other bus underneath the root bus it does support ECAM access.
Add specific quirks for PCI config space accessors. This involves:
1. New initialization call hisi_pcie_init() to obtain RC base
addresses from PNP0C02 at the root of the ACPI namespace (under \_SB).
2. New entry in common quirk array.
[bhelgaas: move to pcie-hisi.c and change Makefile/ifdefs so quirk doesn't
depend on CONFIG_PCI_HISI]
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Qualcomm Technologies QDF2432 SoC does not support accesses smaller
than 32 bits to the PCI configuration space. Register the appropriate
quirk.
[bhelgaas: add QCOM_ECAM32 macro, ifdef for ACPI and PCI_QUIRKS]
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe spec (r3.0, sec 7.2.2) specifies an "Enhanced Configuration Access
Mechanism" (ECAM) for memory-mapped access to configuration space. ECAM is
required for PCIe systems unless there's a standard firmware interface for
config access.
In the absence of a firmware interface, we use pci_generic_ecam_ops, and on
ACPI systems, we discover the ECAM space via the MCFG table and/or the _CBA
method.
Unfortunately some systems provide MCFG but don't implement ECAM according
to spec, so we need a mechanism for quirks to make those systems work.
Add an MCFG quirk mechanism to override the config accessor functions
and/or the memory-mapped address space.
A quirk is selected if it matches all of the following:
- OEM ID
- OEM Table ID
- OEM Revision
- PCI segment (from _SEG)
- PCI bus number range (from _CRS, wildcard allowed)
If the quirk specifies config accessor functions or a memory-mapped address
range, these override the defaults.
[bhelgaas: changelog, reorder quirk matching, fix oem_revision typo per
Duc, add under #ifdef CONFIG_PCI_QUIRKS]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_mcfg_lookup() is the external interface to the generic MCFG code.
Previously it merely looked up the ECAM base address for a given domain and
bus range. We want a way to add MCFG quirks, some of which may require
special config accessors and adjustments to the ECAM address range.
Extend pci_mcfg_lookup() so it can return a pointer to a pci_ecam_ops
structure and a struct resource for the ECAM address space. For now, it
always returns &pci_generic_ecam_ops (the standard accessor) and the
resource described by the MCFG.
No functional changes intended.
[bhelgaas: changelog]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On ACPI systems that support memory-mapped config space access, i.e., ECAM,
the PCI Firmware Specification says the OS can learn where the ECAM space
is from either:
- the static MCFG table (for non-hotpluggable bridges), or
- the _CBA method (for hotpluggable bridges)
The current MCFG table handling code cannot be easily generalized owing to
x86-specific quirks, which makes it hard to reuse on other architectures.
Implement generic MCFG handling from scratch, including:
- Simple MCFG table parsing (via pci_mmcfg_late_init() as in current x86)
- MCFG region lookup for a (domain, bus_start, bus_end) tuple
[bhelgaas: changelog]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Zhou Wang