Timer overrides are normally disabled on Nvidia board because
they are commonly wrong, except on new ones with HPET support.
Unfortunately there are quite some Asus boards around that
don't have HPET, but need a timer override.
We don't know yet how to handle this transparently,
but at least add a command line option to force the timer override
and let them boot.
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Problem:
New Dell PowerEdge servers have 2 embedded ethernet ports, which are
labeled NIC1 and NIC2 on the chassis, in the BIOS setup screens, and
in the printed documentation. Assuming no other add-in ethernet ports
in the system, Linux 2.4 kernels name these eth0 and eth1
respectively. Many people have come to expect this naming. Linux 2.6
kernels name these eth1 and eth0 respectively (backwards from
expectations). I also have reports that various Sun and HP servers
have similar behavior.
Root cause:
Linux 2.4 kernels walk the pci_devices list, which happens to be
sorted in breadth-first order (or pcbios_find_device order on i386,
which most often is breadth-first also). 2.6 kernels have both the
pci_devices list and the pci_bus_type.klist_devices list, the latter
is what is walked at driver load time to match the pci_id tables; this
klist happens to be in depth-first order.
On systems where, for physical routing reasons, NIC1 appears on a
lower bus number than NIC2, but NIC2's bridge is discovered first in
the depth-first ordering, NIC2 will be discovered before NIC1. If the
list were sorted breadth-first, NIC1 would be discovered before NIC2.
A PowerEdge 1955 system has the following topology which easily
exhibits the difference between depth-first and breadth-first device
lists.
-[0000:00]-+-00.0 Intel Corporation 5000P Chipset Memory Controller Hub
+-02.0-[0000:03-08]--+-00.0-[0000:04-07]--+-00.0-[0000:05-06]----00.0-[0000:06]----00.0 Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC2, 2.4 kernel name eth1, 2.6 kernel name eth0)
+-1c.0-[0000:01-02]----00.0-[0000:02]----00.0 Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC1, 2.4 kernel name eth0, 2.6 kernel name eth1)
Other factors, such as device driver load order and the presence of
PCI slots at various points in the bus hierarchy further complicate
this problem; I'm not trying to solve those here, just restore the
device order, and thus basic behavior, that 2.4 kernels had.
Solution:
The solution can come in multiple steps.
Suggested fix#1: kernel
Patch below optionally sorts the two device lists into breadth-first
ordering to maintain compatibility with 2.4 kernels. It adds two new
command line options:
pci=bfsort
pci=nobfsort
to force the sort order, or not, as you wish. It also adds DMI checks
for the specific Dell systems which exhibit "backwards" ordering, to
make them "right".
Suggested fix#2: udev rules from userland
Many people also have the expectation that embedded NICs are always
discovered before add-in NICs (which this patch does not try to do).
Using the PCI IRQ Routing Table provided by system BIOS, it's easy to
determine which PCI devices are embedded, or if add-in, which PCI slot
they're in. I'm working on a tool that would allow udev to name
ethernet devices in ascending embedded, slot 1 .. slot N order,
subsort by PCI bus/dev/fn breadth-first. It'll be possible to use it
independent of udev as well for those distributions that don't use
udev in their installers.
Suggested fix#3: system board routing rules
One can constrain the system board layout to put NIC1 ahead of NIC2
regardless of breadth-first or depth-first discovery order. This adds
a significant level of complexity to board routing, and may not be
possible in all instances (witness the above systems from several
major manufacturers). I don't want to encourage this particular train
of thought too far, at the expense of not doing #1 or #2 above.
Feedback appreciated. Patch tested on a Dell PowerEdge 1955 blade
with 2.6.18.
You'll also note I took some liberty and temporarily break the klist
abstraction to simplify and speed up the sort algorithm. I think
that's both safe and appropriate in this instance.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since it often takes around 20-30 seconds to scan a scsi bus, it's
highly advantageous to do this in parallel with other things. The bulk
of this patch is ensuring that devices don't change numbering, and that
all devices are discovered prior to trying to start init. For those
who build SCSI as modules, there's a new scsi_wait_scan module that will
ensure all bus scans are finished.
This patch only handles drivers which call scsi_scan_host. Fibre Channel,
SAS, SATA, USB and Firewire all need additional work.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains the scheduled removal of OSS drivers that:
- have ALSA drivers for the same hardware without known regressions and
- whose Kconfig options have been removed in 2.6.17.
[michal.k.k.piotrowski@gmail.com: build fix]
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kill a hard-to-calculate 'rsinterval' boot parameter and per-cpu
rcu_data.last_rs_qlen. Instead, it adds adds a flag rcu_ctrlblk.signaled,
which records the fact that one of CPUs has sent a resched IPI since the
last rcu_start_batch().
Roughly speaking, we need two rcu_start_batch()s in order to move callbacks
from ->nxtlist to ->donelist. This means that when ->qlen exceeds qhimark
and continues to grow, we should send a resched IPI, and then do it again
after we gone through a quiescent state.
On the other hand, if it was already sent, we don't need to do it again
when another CPU detects overflow of the queue.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Documentation fix for the arm and arm26 architectures,
in which the reboot kernel parameter is set in arch/*/kernel/process.c
Signed-off-by: Michael Opdenacker <michael@free-electrons.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Randy brought it to my attention that in proper english "can not" should always
be written "cannot". I donot see any reason to argue, even if I mightnot
understand why this rule exists. This patch fixes "can not" in several
Documentation files as well as three Kconfigs.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch fixes typos in various Documentation txts.
This patch addresses some words starting with the letter 'A'.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Fix "quiet" parameter doc. No trailing '=' sign, no value after it. And
it disables "most" kernel messages, not all of them.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Resetting the devices during driver initialization can be a costly
operation in terms of time (especially scsi devices). This option can be
used by drivers to know that user forcibly wants the devices to be reset
during initialization.
This option can be useful while kernel is booting in unreliable
environment. For ex. during kdump boot where devices are in unknown
random state and BIOS execution has been skipped.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: (225 commits)
[PATCH] Don't set calgary iommu as default y
[PATCH] i386/x86-64: New Intel feature flags
[PATCH] x86: Add a cumulative thermal throttle event counter.
[PATCH] i386: Make the jiffies compares use the 64bit safe macros.
[PATCH] x86: Refactor thermal throttle processing
[PATCH] Add 64bit jiffies compares (for use with get_jiffies_64)
[PATCH] Fix unwinder warning in traps.c
[PATCH] x86: Allow disabling early pci scans with pci=noearly or disallowing conf1
[PATCH] x86: Move direct PCI scanning functions out of line
[PATCH] i386/x86-64: Make all early PCI scans dependent on CONFIG_PCI
[PATCH] Don't leak NT bit into next task
[PATCH] i386/x86-64: Work around gcc bug with noreturn functions in unwinder
[PATCH] Fix some broken white space in ia32_signal.c
[PATCH] Initialize argument registers for 32bit signal handlers.
[PATCH] Remove all traces of signal number conversion
[PATCH] Don't synchronize time reading on single core AMD systems
[PATCH] Remove outdated comment in x86-64 mmconfig code
[PATCH] Use string instructions for Core2 copy/clear
[PATCH] x86: - restore i8259A eoi status on resume
[PATCH] i386: Split multi-line printk in oops output.
...
Add a boot parameter to reserve high linear address space for hypervisors.
This is necessary to allow dynamically loaded hypervisor modules, which might
not happen until userspace is already running, and also provides a useful tool
to benchmark the performance impact of reduced lowmem address space.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some buggy systems can machine check when config space accesses
happen for some non existent devices. i386/x86-64 do some early
device scans that might trigger this. Allow pci=noearly to disable
this. Also when type 1 is disabling also don't do any early
accesses which are always type1.
This moves the pci= configuration parsing to be a early parameter.
I don't think this can break anything because it only changes
a single global that is only used by PCI.
Cc: gregkh@suse.de
Cc: Trammell Hudson <hudson@osresearch.net>
Signed-off-by: Andi Kleen <ak@suse.de>
This reverts commits 11012d419c and
40dd2d20f2, which allowed us to use the
MMIO accesses for PCI config cycles even without the area being marked
reserved in the e820 memory tables.
Those changes were needed for EFI-environment Intel macs, but broke some
newer Intel 965 boards, so for now it's better to revert to our old
2.6.17 behaviour and at least avoid introducing any new breakage.
Andi Kleen has a set of patches that work with both EFI and the broken
Intel 965 boards, which will be applied once they get wider testing.
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Edgar Hucek <hostmaster@ed-soft.at>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I'm not sure if documenting this here is appropriate, but
if it is, here is some text to put there.
Signed-Off-By: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a replacement for the earlier removal of the e820 MCFG check
we blacklist the Intel SDV with the original BIOS bug that
motivated that check. On those machines don't use MMCONFIG.
This also adds a new pci=mmconf parameter to override the blacklist.
Cc: Greg KH <gregkh@suse.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable delay accounting by default so that feature gets coverage testing
without requiring special measures.
Earlier, it was off by default and had to be enabled via a boot time param.
This patch reverses the default behaviour to improve coverage testing. It
can be removed late in the kernel development cycle if its believed users
shouldn't have to incur any cost if they don't want delay accounting. Or
it can be retained forever if the utility of the stats is deemed common
enough to warrant keeping the feature on.
Signed-off-by: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initialization code related to collection of per-task "delay" statistics which
measure how long it had to wait for cpu, sync block io, swapping etc. The
collection of statistics and the interface are in other patches. This patch
sets up the data structures and allows the statistics collection to be
disabled through a kernel boot parameter.
Signed-off-by: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Balbir Singh <balbir@in.ibm.com>
Cc: Jes Sorensen <jes@sgi.com>
Cc: Peter Chubb <peterc@gelato.unsw.edu.au>
Cc: Erich Focht <efocht@ess.nec.de>
Cc: Levent Serinol <lserinol@gmail.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce DEBUG_LOCKING_API_SELFTESTS, which uses the generic lock debugging
code's silent-failure feature to run a matrix of testcases. There are 210
testcases currently:
+-----------------------
| Locking API testsuite:
+------------------------------+------+------+------+------+------+------+
| spin |wlock |rlock |mutex | wsem | rsem |
-------------------------------+------+------+------+------+------+------+
A-A deadlock: ok | ok | ok | ok | ok | ok |
A-B-B-A deadlock: ok | ok | ok | ok | ok | ok |
A-B-B-C-C-A deadlock: ok | ok | ok | ok | ok | ok |
A-B-C-A-B-C deadlock: ok | ok | ok | ok | ok | ok |
A-B-B-C-C-D-D-A deadlock: ok | ok | ok | ok | ok | ok |
A-B-C-D-B-D-D-A deadlock: ok | ok | ok | ok | ok | ok |
A-B-C-D-B-C-D-A deadlock: ok | ok | ok | ok | ok | ok |
double unlock: ok | ok | ok | ok | ok | ok |
bad unlock order: ok | ok | ok | ok | ok | ok |
--------------------------------------+------+------+------+------+------+
recursive read-lock: | ok | | ok |
--------------------------------------+------+------+------+------+------+
non-nested unlock: ok | ok | ok | ok |
--------------------------------------+------+------+------+
hard-irqs-on + irq-safe-A/12: ok | ok | ok |
soft-irqs-on + irq-safe-A/12: ok | ok | ok |
hard-irqs-on + irq-safe-A/21: ok | ok | ok |
soft-irqs-on + irq-safe-A/21: ok | ok | ok |
sirq-safe-A => hirqs-on/12: ok | ok | ok |
sirq-safe-A => hirqs-on/21: ok | ok | ok |
hard-safe-A + irqs-on/12: ok | ok | ok |
soft-safe-A + irqs-on/12: ok | ok | ok |
hard-safe-A + irqs-on/21: ok | ok | ok |
soft-safe-A + irqs-on/21: ok | ok | ok |
hard-safe-A + unsafe-B #1/123: ok | ok | ok |
soft-safe-A + unsafe-B #1/123: ok | ok | ok |
hard-safe-A + unsafe-B #1/132: ok | ok | ok |
soft-safe-A + unsafe-B #1/132: ok | ok | ok |
hard-safe-A + unsafe-B #1/213: ok | ok | ok |
soft-safe-A + unsafe-B #1/213: ok | ok | ok |
hard-safe-A + unsafe-B #1/231: ok | ok | ok |
soft-safe-A + unsafe-B #1/231: ok | ok | ok |
hard-safe-A + unsafe-B #1/312: ok | ok | ok |
soft-safe-A + unsafe-B #1/312: ok | ok | ok |
hard-safe-A + unsafe-B #1/321: ok | ok | ok |
soft-safe-A + unsafe-B #1/321: ok | ok | ok |
hard-safe-A + unsafe-B #2/123: ok | ok | ok |
soft-safe-A + unsafe-B #2/123: ok | ok | ok |
hard-safe-A + unsafe-B #2/132: ok | ok | ok |
soft-safe-A + unsafe-B #2/132: ok | ok | ok |
hard-safe-A + unsafe-B #2/213: ok | ok | ok |
soft-safe-A + unsafe-B #2/213: ok | ok | ok |
hard-safe-A + unsafe-B #2/231: ok | ok | ok |
soft-safe-A + unsafe-B #2/231: ok | ok | ok |
hard-safe-A + unsafe-B #2/312: ok | ok | ok |
soft-safe-A + unsafe-B #2/312: ok | ok | ok |
hard-safe-A + unsafe-B #2/321: ok | ok | ok |
soft-safe-A + unsafe-B #2/321: ok | ok | ok |
hard-irq lock-inversion/123: ok | ok | ok |
soft-irq lock-inversion/123: ok | ok | ok |
hard-irq lock-inversion/132: ok | ok | ok |
soft-irq lock-inversion/132: ok | ok | ok |
hard-irq lock-inversion/213: ok | ok | ok |
soft-irq lock-inversion/213: ok | ok | ok |
hard-irq lock-inversion/231: ok | ok | ok |
soft-irq lock-inversion/231: ok | ok | ok |
hard-irq lock-inversion/312: ok | ok | ok |
soft-irq lock-inversion/312: ok | ok | ok |
hard-irq lock-inversion/321: ok | ok | ok |
soft-irq lock-inversion/321: ok | ok | ok |
hard-irq read-recursion/123: ok |
soft-irq read-recursion/123: ok |
hard-irq read-recursion/132: ok |
soft-irq read-recursion/132: ok |
hard-irq read-recursion/213: ok |
soft-irq read-recursion/213: ok |
hard-irq read-recursion/231: ok |
soft-irq read-recursion/231: ok |
hard-irq read-recursion/312: ok |
soft-irq read-recursion/312: ok |
hard-irq read-recursion/321: ok |
soft-irq read-recursion/321: ok |
--------------------------------+-----+----------------
Good, all 210 testcases passed! |
--------------------------------+
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
Implementation of new kernel parameter vmpanic that provides a means to
perform a z/VM CP command after a kernel panic occurred.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move the i386 VDSO down into a vma and thus randomize it.
Besides the security implications, this feature also helps debuggers, which
can COW a vma-backed VDSO just like a normal DSO and can thus do
single-stepping and other debugging features.
It's good for hypervisors (Xen, VMWare) too, which typically live in the same
high-mapped address space as the VDSO, hence whenever the VDSO is used, they
get lots of guest pagefaults and have to fix such guest accesses up - which
slows things down instead of speeding things up (the primary purpose of the
VDSO).
There's a new CONFIG_COMPAT_VDSO (default=y) option, which provides support
for older glibcs that still rely on a prelinked high-mapped VDSO. Newer
distributions (using glibc 2.3.3 or later) can turn this option off. Turning
it off is also recommended for security reasons: attackers cannot use the
predictable high-mapped VDSO page as syscall trampoline anymore.
There is a new vdso=[0|1] boot option as well, and a runtime
/proc/sys/vm/vdso_enabled sysctl switch, that allows the VDSO to be turned
on/off.
(This version of the VDSO-randomization patch also has working ELF
coredumping, the previous patch crashed in the coredumping code.)
This code is a combined work of the exec-shield VDSO randomization
code and Gerd Hoffmann's hypervisor-centric VDSO patch. Rusty Russell
started this patch and i completed it.
[akpm@osdl.org: cleanups]
[akpm@osdl.org: compile fix]
[akpm@osdl.org: compile fix 2]
[akpm@osdl.org: compile fix 3]
[akpm@osdl.org: revernt MAXMEM change]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Cc: Gerd Hoffmann <kraxel@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement the time sources for i386 (acpi_pm, cyclone, hpet, pit, and tsc).
With this patch, the conversion of the i386 arch to the generic timekeeping
code should be complete.
The patch should be fairly straight forward, only adding the new clocksources.
[hirofumi@mail.parknet.co.jp: acpi_pm cleanup]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This introduces the clocksource management infrastructure. A clocksource is a
driver-like architecture generic abstraction of a free-running counter. This
code defines the clocksource structure, and provides management code for
registering, selecting, accessing and scaling clocksources.
Additionally, this includes the trivial jiffies clocksource, a lowest common
denominator clocksource, provided mainly for use as an example.
[hirofumi@mail.parknet.co.jp: Don't enable IRQ too early]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (65 commits)
ACPI: suppress power button event on S3 resume
ACPI: resolve merge conflict between sem2mutex and processor_perflib.c
ACPI: use for_each_possible_cpu() instead of for_each_cpu()
ACPI: delete newly added debugging macros in processor_perflib.c
ACPI: UP build fix for bugzilla-5737
Enable P-state software coordination via _PDC
P-state software coordination for speedstep-centrino
P-state software coordination for acpi-cpufreq
P-state software coordination for ACPI core
ACPI: create acpi_thermal_resume()
ACPI: create acpi_fan_suspend()/acpi_fan_resume()
ACPI: pass pm_message_t from acpi_device_suspend() to root_suspend()
ACPI: create acpi_device_suspend()/acpi_device_resume()
ACPI: replace spin_lock_irq with mutex for ec poll mode
ACPI: Allow a WAN module enable/disable on a Thinkpad X60.
sem2mutex: acpi, acpi_link_lock
ACPI: delete unused acpi_bus_drivers_lock
sem2mutex: drivers/acpi/processor_perflib.c
ACPI add ia64 exports to build acpi_memhotplug as a module
ACPI: asus_acpi_init(): propagate correct return value
...
Manual resolve of conflicts in:
arch/i386/kernel/cpu/cpufreq/acpi-cpufreq.c
arch/i386/kernel/cpu/cpufreq/speedstep-centrino.c
include/acpi/processor.h
Add new per-packet access controls to SELinux, replacing the old
packet controls.
Packets are labeled with the iptables SECMARK and CONNSECMARK targets,
then security policy for the packets is enforced with these controls.
To allow for a smooth transition to the new controls, the old code is
still present, but not active by default. To restore previous
behavior, the old controls may be activated at runtime by writing a
'1' to /selinux/compat_net, and also via the kernel boot parameter
selinux_compat_net. Switching between the network control models
requires the security load_policy permission. The old controls will
probably eventually be removed and any continued use is discouraged.
With this patch, the new secmark controls for SElinux are disabled by
default, so existing behavior is entirely preserved, and the user is
not affected at all.
It also provides a config option to enable the secmark controls by
default (which can always be overridden at boot and runtime). It is
also noted in the kconfig help that the user will need updated
userspace if enabling secmark controls for SELinux and that they'll
probably need the SECMARK and CONNMARK targets, and conntrack protocol
helpers, although such decisions are beyond the scope of kernel
configuration.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch somewhat diverted the train of thought.
Here I am trying to bring the valued reader back on track.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Doc/kernel-parameters.txt: mention modinfo and sysfs
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Doc/kernel-parameters.txt: delete false version information and history
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
My patch to add brief documentation of the nomca boot parameter
added it out of alphabetical order.
Signed-Off-By: Horms <horms@verge.net.au>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This can sometimes be used to work around broken BIOS.
Use "Microsoft Windows" to take the same path
through the BIOS as Windows98 would.
The default is "Microsoft Windows NT", which
is what NT and later versions of Windows use,
and is the most tested path through most BIOS.
Set it to anything else, including "Linux", at your
own risk, as it seems that virtually no BIOS
has been tested with anything but the two options above.
Note that this uses the legacy _OS interface, so
we don't expect this to ever change.
Signed-off-by: Len Brown <len.brown@intel.com>
Add info on flow control for serial consoles. Refer to netconsole option
also.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Several drivers are starting to grow options to disable MSI. However,
it's often a host chipset issue, not something which individual drivers
should handle. So we add the pci=nomsi kernel parameter to allow the user
to disable MSI modes for systems we haven't added to the quirk list yet.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Attempt to fix the problem wherein people's oops reports scroll off the screen
due to repeated oopsing or to oopses on other CPUs.
If this happens the user can reboot with the `pause_on_oops=<seconds>' option.
It will allow the first oopsing CPU to print an oops record just a single
time. Second oopsing attempts, or oopses on other CPUs will cause those CPUs
to enter a tight loop until the specified number of seconds have elapsed.
The patch implements the infrastructure generically in the expectation that
architectures other than x86 will find it useful.
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow the x86 "sep" feature to be disabled at bootup. This forces use of the
int80 vsyscall. Mainly for testing or benchmarking the int80 vsyscall code.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ATI chipsets tend to generate double timer interrupts for the local APIC
timer when both the 8254 and the IO-APIC timer pins are enabled. This is
because they route it to both and the result is anded together and the CPU
ends up processing it twice.
This patch changes check_timer to disable the 8254 routing for interrupt 0.
I think it would be safe on all chipsets actually (i tested it on a couple
and it worked everywhere) and Windows seems to do it in a similar way, but
to be conservative this patch only enables this mode on ATI (and adds
options to enable/disable too)
Ported over from a similar x86-64 change.
I reused the ACPI earlyquirk infrastructure for the ATI bridge check, but
tweaked it a bit to work even without ACPI.
Inspired by a patch from Chuck Ebbert, but redone.
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds new tunables for RCU queue and finished batches. There are
two types of controls - number of completed RCU updates invoked in a batch
(blimit) and monitoring for high rate of incoming RCUs on a cpu (qhimark,
qlowmark).
By default, the per-cpu batch limit is set to a small value. If the input
RCU rate exceeds the high watermark, we do two things - force quiescent
state on all cpus and set the batch limit of the CPU to INTMAX. Setting
batch limit to INTMAX forces all finished RCUs to be processed in one shot.
If we have more than INTMAX RCUs queued up, then we have bigger problems
anyway. Once the incoming queued RCUs fall below the low watermark, the
batch limit is set to the default.
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AMD SimNow!'s JIT doesn't like them at all in the guest. For distribution
installation it's easiest if it's a boot time option.
Also I moved the variable to a more appropiate place and make
it independent from sysctl
And marked __read_mostly which it is.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Ingo Molnar <mingo@elte.hu>
This is the latest version of the scheduler cache-hot-auto-tune patch.
The first problem was that detection time scaled with O(N^2), which is
unacceptable on larger SMP and NUMA systems. To solve this:
- I've added a 'domain distance' function, which is used to cache
measurement results. Each distance is only measured once. This means
that e.g. on NUMA distances of 0, 1 and 2 might be measured, on HT
distances 0 and 1, and on SMP distance 0 is measured. The code walks
the domain tree to determine the distance, so it automatically follows
whatever hierarchy an architecture sets up. This cuts down on the boot
time significantly and removes the O(N^2) limit. The only assumption
is that migration costs can be expressed as a function of domain
distance - this covers the overwhelming majority of existing systems,
and is a good guess even for more assymetric systems.
[ People hacking systems that have assymetries that break this
assumption (e.g. different CPU speeds) should experiment a bit with
the cpu_distance() function. Adding a ->migration_distance factor to
the domain structure would be one possible solution - but lets first
see the problem systems, if they exist at all. Lets not overdesign. ]
Another problem was that only a single cache-size was used for measuring
the cost of migration, and most architectures didnt set that variable
up. Furthermore, a single cache-size does not fit NUMA hierarchies with
L3 caches and does not fit HT setups, where different CPUs will often
have different 'effective cache sizes'. To solve this problem:
- Instead of relying on a single cache-size provided by the platform and
sticking to it, the code now auto-detects the 'effective migration
cost' between two measured CPUs, via iterating through a wide range of
cachesizes. The code searches for the maximum migration cost, which
occurs when the working set of the test-workload falls just below the
'effective cache size'. I.e. real-life optimized search is done for
the maximum migration cost, between two real CPUs.
This, amongst other things, has the positive effect hat if e.g. two
CPUs share a L2/L3 cache, a different (and accurate) migration cost
will be found than between two CPUs on the same system that dont share
any caches.
(The reliable measurement of migration costs is tricky - see the source
for details.)
Furthermore i've added various boot-time options to override/tune
migration behavior.
Firstly, there's a blanket override for autodetection:
migration_cost=1000,2000,3000
will override the depth 0/1/2 values with 1msec/2msec/3msec values.
Secondly, there's a global factor that can be used to increase (or
decrease) the autodetected values:
migration_factor=120
will increase the autodetected values by 20%. This option is useful to
tune things in a workload-dependent way - e.g. if a workload is
cache-insensitive then CPU utilization can be maximized by specifying
migration_factor=0.
I've tested the autodetection code quite extensively on x86, on 3
P3/Xeon/2MB, and the autodetected values look pretty good:
Dual Celeron (128K L2 cache):
---------------------
migration cost matrix (max_cache_size: 131072, cpu: 467 MHz):
---------------------
[00] [01]
[00]: - 1.7(1)
[01]: 1.7(1) -
---------------------
cacheflush times [2]: 0.0 (0) 1.7 (1784008)
---------------------
Here the slow memory subsystem dominates system performance, and even
though caches are small, the migration cost is 1.7 msecs.
Dual HT P4 (512K L2 cache):
---------------------
migration cost matrix (max_cache_size: 524288, cpu: 2379 MHz):
---------------------
[00] [01] [02] [03]
[00]: - 0.4(1) 0.0(0) 0.4(1)
[01]: 0.4(1) - 0.4(1) 0.0(0)
[02]: 0.0(0) 0.4(1) - 0.4(1)
[03]: 0.4(1) 0.0(0) 0.4(1) -
---------------------
cacheflush times [2]: 0.0 (33900) 0.4 (448514)
---------------------
Here it can be seen that there is no migration cost between two HT
siblings (CPU#0/2 and CPU#1/3 are separate physical CPUs). A fast memory
system makes inter-physical-CPU migration pretty cheap: 0.4 msecs.
8-way P3/Xeon [2MB L2 cache]:
---------------------
migration cost matrix (max_cache_size: 2097152, cpu: 700 MHz):
---------------------
[00] [01] [02] [03] [04] [05] [06] [07]
[00]: - 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[01]: 19.2(1) - 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[02]: 19.2(1) 19.2(1) - 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[03]: 19.2(1) 19.2(1) 19.2(1) - 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[04]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) - 19.2(1) 19.2(1) 19.2(1)
[05]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) - 19.2(1) 19.2(1)
[06]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) - 19.2(1)
[07]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) -
---------------------
cacheflush times [2]: 0.0 (0) 19.2 (19281756)
---------------------
This one has huge caches and a relatively slow memory subsystem - so the
migration cost is 19 msecs.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Cc: <wilder@us.ibm.com>
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- elfcorehdr= specifies the location of elf core header stored by the
crashed kernel. This command line option will be passed by the kexec-tools
to capture kernel.
Changes in this version :
- Added more comments in kernel-parameters.txt and in code.
Signed-off-by: Murali M Chakravarthy <muralim@in.ibm.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Vivek Goyal <vgoyal@in.ibm.com>
- This patch introduces the memmap option for x86_64 similar to i386.
- memmap=exactmap enables setting of an exact E820 memory map, as specified
by the user.
Changes in this version:
- Used e820_end_of_ram() to find the max_pfn as suggested by Andi kleen.
- removed PFN_UP & PFN_DOWN macros
- Printing the user defined map also.
Signed-off-by: Murali M Chakravarthy <muralim@in.ibm.com>
Signed-off-by: Hariprasad Nellitheertha <nharipra@gmail.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Also add a nr_uarts module option to the 8250 code to override
this, up to a maximum of CONFIG_SERIAL_8250_NR_UARTS
This should appease people who complain about a proliferation
of /dev/ttyS & /sysfs nodes whilst at the same time allowing
a single kernel image to support the rarer occasions of
lots of devices.
Signed-off-by: Dave Jones <davej@redhat.com>
If someone changes the uid/gid mapping in userland, then we do eventually
want those changes to be propagated to the kernel. Currently the kernel
assumes that it may cache entries forever.
Add an expiration time + garbage collector for idmap entries.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Combined mode sucks. Especially when both libata and the legacy IDE
drivers try to drive ports on the same device, since that makes DMA
rather difficult.
This patch addresses the problem by allowing the user to control which
driver binds to the ports in a combined mode configuration. In many
cases, they'll probably want the libata driver to control both ports
since it can use DMA for talking with ATAPI devices (when
libata.atapi_enabled=1 of course). It also allows the user to get old
school behavior by letting the legacy IDE driver bind to both ports.
But neither is forced, the patch doesn't change current behavior unless
one of combined_mode=ide or combined_mode=libata is passed
on the boot line. Either of those options may require you to access
your devices via different device nodes (/dev/hd* in the ide case
and /dev/sd* in the libata case), though of course if you have udev
installed nicely you may not notice anything. :)
Let me know if the documentation is too cryptic, I'd be happy to expand
on it if necessary. I think most users will want to boot with
'combined_mode=libata' and add 'options libata atapi_enabled=1'
to their modules.conf to get good DVD playing and disk behavior
(haven't tested CD or DVD writing though).
I'd much rather things behave sanely by default (i.e. DMA for devices on
both ports), but apparently that's difficult given the various chip
bugs and hardware configs out there (not to mention that people's
drives may suddenly change from /dev/hdc to /dev/sdb), so this boot
option may be the correct long term fix.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Please, please now delete the Atari CONFIG_STRAM_SWAP code. It may be
excellent and ingenious code, but its reference to swap_vfsmnt betrays that it
hasn't been built since 2.5.1 (four years old come December), it's delving
deep into matters which are the preserve of core mm code, its only purpose is
to give the more conscientious mm guys an anxiety attack from time to time;
yet we keep on breaking it more and more.
If you want to use RAM for swap, then if the MTD driver does not already
provide just what you need, I'm sure David could be persuaded to add the
extra. But you'd also like to be able to allocate extents of that swap for
other use: we can give you a core interface for that if you need. But unbuilt
for four years suggests to me that there's no need at all.
I cannot swear the patch below won't break your build, but believe so.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This revised patch (as586b) makes usb-handoff permanently true and no
longer a kernel boot parameter. It also removes the piix3_usb quirk code;
that was nothing more than an early version of the USB handoff code
(written at a time when Intel's PIIX3 was about the only motherboard with
USB support). And it adds identifiers for the three PCI USB controller
classes to pci_ids.h.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix typos & trailing whitespace.
Add blank lines in a few places.
Remove "AM53C974=" option: driver does not exist.
Restrict to < 80 columns in most places (but don't split formatted
command-line arguments).
Add a few option arguments for completeness.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Original patch from Bertro Simul
This is probably still not quite correct, but seems to be
the best solution so far.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since early userspace was added, there's no way to override which init to
run from it. Some people tack on an extra cpio archive with a link from
/init depending on what they want to run, but that's sometimes impractical.
Changing the "init=" to also override the early userspace isn't feasible,
since it is still used to indicate what init to run from disk when early
userspace has completed doing whatever it's doing (i.e. load filesystem
modules and drivers).
Instead, introduce "rdinit=" and make it override the default "/init" if
specified.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When both platform-specific and generic drivers exist,
enable generic over-ride with "acpi_generic_hotkey".
http://bugzilla.kernel.org/show_bug.cgi?id=4953
Signed-off-by: Luming Yu <luming.yu@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This is a small documentation patch for a boot time parameter.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Anyone reporting a stuck IRQ should try these options. Its effectiveness
varies we've found in the Fedora case. Quite a few systems with misdescribed
IRQ routing just work when you use irqpoll. It also fixes up the VIA systems
although thats now fixed with the VIA quirk (which we could just make default
as its what Redmond OS does but Linus didn't like it historically).
A small number of systems have jammed IRQ sources or misdescribes that cause
an IRQ that we have no handler registered anywhere for. In those cases it
doesn't help.
Signed-off-by: Alan Cox <number6@the-village.bc.nu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I updated this to remove unnecessary variable initialization, make
check_routing be inline only and not __init, switch to strtoul, and
formatting fixes as per Randy Dunlap's recommendations.
I updated this to change pirq_table_addr to a long, and to add a warning
msg if the PIRQ table wasn't found at the specified address, as per thread
with Matthew Wilcox.
In our hardware situation, the BIOS is unable to store or generate it's PIRQ
table in the F0000h-100000h standard range. This patch adds a pci kernel
parameter, pirqaddr to allow the bootloader (or BIOS based loader) to inform
the kernel where the PIRQ table got stored. A beneficial side-effect is that,
if one's BIOS uses a static address each time for it's PIRQ table, then
pirqaddr can be used to avoid the $pirq search through that address block each
time at boot for normal PIRQ BIOSes.
Signed-off-by: Jaya Kumar <jayalk@intworks.biz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for retrieving the address of elf core header if one
is passed in command line.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces the architecture independent implementation the
sys_kexec_load, the compat_sys_kexec_load system calls.
Kexec on panic support has been integrated into the core patch and is
relatively clean.
In addition the hopefully architecture independent option
crashkernel=size@location has been docuemented. It's purpose is to reserve
space for the panic kernel to live, and where no DMA transfer will ever be
setup to access.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I8K: Change to use stock dmi infrastructure instead of homegrown
parsing code. The driver now requires box's DMI data to match
list of supported models so driver can be safely compiled-in
by default without fear of it poking into random SMM BIOS
code. DMI checks can be ignored with i8k.ignore_dmi option.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Andi Kleen