New driver for NXP (Philips) UART ICs was introduced in September 2012.
Old driver no longer used anywhere, this patch removes it.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the initialisation of older Quatech serial cards which are fitted with
the AMCC PCI Matchmaker interface chip.
Signed-off-by: Jonathan Woithe (jwoithe@just42.net)
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 'tty: xuartps: Implement BREAK detection, add SYSRQ support'
(0c0c47bc40) introduced sysrq support
without properly guarding sysrq specific code which results in build
errors when sysrq is disabled:
DNAME=KBUILD_STR(xilinx_uartps)" -c -o
drivers/tty/serial/.tmp_xilinx_uartps.o
drivers/tty/serial/xilinx_uartps.c
drivers/tty/serial/xilinx_uartps.c: In function 'xuartps_isr':
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
make[3]: *** [drivers/tty/serial/xilinx_uartps.o] Error 1
Reported-by: Masanari Iida <standby24x7@gmail.com>
Cc: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer Intel PCHs with LPSS have the same Designware controllers than
Haswell but ACPI IDs are different. Add these IDs to the driver list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When falling back from DMA to interrupt mode the receive interrupt has to
be re-enabled to catch new incoming data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In pl011_rx_chars() if pl011_dma_rx_trigger_dma() succeeds it will disable
the receive interrupt, no need to do this again.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During initialisation, a UART may already be in use for a console, so
take care to preserve things like baud rate and data format to avoid
corrupting console output.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code to cope with a split tx/rx LCR_H register is non-trivial
so put it into it's own function to avoid duplication.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the pl011 is being used for a console, pl011_console_write forces
the control register (CR) to enable the UART for transmission and then
restores this to the original value afterwards. It does this while
holding the port lock.
Unfortunately, when the uart is started or shutdown - say in response to
userland using the serial device for a terminal - then this updates the
control register without any locking.
This means we can have
pl011_console_write Save CR
pl011_startup Initialise CR, e.g. enable receive
pl011_console_write Restore old CR with receive not enabled
this result is a serial port which doesn't respond to any input.
A similar race in reverse could happen when the device is shutdown.
We can fix these problems by taking the port lock when updating CR.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 17438217a6 on request
of Linus Walleij:
Greg can you please drop or revert
commit 17438217a6
"serial: pl011: use DMA RX polling by default"
from the TTY tree until this has been sorted out?
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a complex patch for refactoring CLPS711X serial driver.
Major changes:
- Eliminate <mach/hardware.h> usage.
- Devicetree support.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c49436b657 (serial: 8250_dw: Improve unwritable LCR workaround)
caused a regression. It added a check that the LCR was written properly
to detect and workaround the busy quirk, but the behaviour of bit 5
(UART_LCR_SPAR) differs between IP versions 3.00a and 3.14c per the
docs. On older versions this caused the check to fail and it would
repeatedly force idle and rewrite the LCR register, causing delays and
preventing any input from serial being received.
This is fixed by masking out UART_LCR_SPAR before making the comparison.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Tim Kryger <tim.kryger@linaro.org>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Matt Porter <matt.porter@linaro.org>
Cc: Markus Mayer <markus.mayer@linaro.org>
Tested-by: Tim Kryger <tim.kryger@linaro.org>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The break timer accesses hardware registers and thus requires the port
to be enabled. It currently ensures this by enabling the port at the
beginning of the timer handler, and disabling it at the end. However,
the enable/disable operations call the runtime PM sync functions, which
are not allowed in atomic context. The current situation is thus broken.
This change relies on non-atomic code to enable/disable the port. The
break timer will only be started from the IRQ handler, which already
runs with the port enabled. We just need to ensure that the port won't
be disabled with the timer running, and that's easily done by just
cancelling the timer in the port disable function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the %zu and %pad printk specifiers to print size_t and dma_addr_t
variables, and cast pointers to uintptr_t instead of unsigned int where
applicable. This fixes warnings on platforms where pointers and/or
dma_addr_t have a different size than int.
Cc: linux-serial@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
By using dma_request_slave_channel_or_err(), the DMA slave ID can be
looked up from standard DT properties, and squirrelled away during
channel allocation. Hence, there's no need to use a custom DT property
to store the slave ID.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Commit 'tty: xuartps: Implement BREAK detection, add SYSRQ support'
(0c0c47bc40) introduced sysrq support
without properly guarding sysrq specific code which results in build
errors when sysrq is disabled:
DNAME=KBUILD_STR(xilinx_uartps)" -c -o
drivers/tty/serial/.tmp_xilinx_uartps.o
drivers/tty/serial/xilinx_uartps.c
drivers/tty/serial/xilinx_uartps.c: In function 'xuartps_isr':
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
make[3]: *** [drivers/tty/serial/xilinx_uartps.o] Error 1
Reported-by: Masanari Iida <standby24x7@gmail.com>
Cc: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the initialisation of older Quatech serial cards which are fitted with
the AMCC PCI Matchmaker interface chip.
Signed-off-by: Jonathan Woithe (jwoithe@just42.net)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use "fw" in the next line after we release it. I've shifted the call
to release_firmware() down a couple lines to fix this.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer Intel PCHs with LPSS have the same Designware controllers than
Haswell but ACPI IDs are different. Add these IDs to the driver list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if the DMA driver isn't loaded "on time" then we crash in the irq handler:
| pch_uart 0000:02:0a.4: pch_request_dma:dma_request_channel FAILS(Tx)
| BUG: unable to handle kernel NULL pointer dereference at (null)
| IP: [<c0676ed9>] pch_uart_interrupt+0x739/0x940
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 60e9357547 (serial: samsung: enable clock before clearing pending
interrupts during init) added handling of the controller clock during init.
On most systems this clock is also one of the baud_clock sources and
possibly used by the earlycon and thus already enabled by the bootloader.
Therefore a gap exists between s3c24xx_serial_init_port disabling the
clock and an attached console reenabling it, making the transition from
earlycon to regular console possibly hang the system - as seen on my
S3C2442 based Freerunner today.
Therefore move the disabling of the clock from s3c24xx_serial_init_port
below the uart port registration, effectively creating an overlap and
keeping the clock running non-stop if the console wants to grab this port.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert to modern PM ops and use the SIMPLE_DEV_PM_OPS macro to set up
the PM callbacks.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Making DMA RX polling optional when DMA is on was just
over-cautious: there is one single system in the kernel tree
using this facility, Ux500 and after some testing I turned
this on also for Ux500, which means it should simply be on
by default if DMA is enabled.
Cc: Jongsung Kim <neidhard.kim@lge.com>
Cc: Chanho Min <chanho.min@lge.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert to modern PM ops and use the SIMPLE_DEV_PM_OPS macro to set up
the PM callbacks.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This early amba_ports declaration was introduced by commit c16d51a32 (amba
pl011: workaround for uart registers lockup) for use in the pl011_lockup_wa()
routine. This routine was later removed by commit 4fd0690bb (serial: pl011:
implement workaround for CTS clear event issue).
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI now provides stubs for the functions the driver uses.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uart_set_options() code unconditionally initalizes the spinlock
on the port. This can cause a deadlock in some situations.
One instance that exposed the problem, was when writing to
/sys/module/kgdboc/parameters/kgdboc to use ttyS0 when the console
is already running on ttyS0. If the spinlock is re-initialized
while the lock is held due to output to the console, there
is a deadlock.
Assume the spinlock is initialized if the port is a console.
Signed-off-by: Randy Witt <rewitt@declaratino.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When booting a multi-platform m68k kernel on a non-Mac with "console=ttyS0"
on the kernel command line, it crashes with:
Unable to handle kernel NULL pointer dereference at virtual address (null)
Oops: 00000000
PC: [<0013ad28>] __pmz_startup+0x32/0x2a0
...
Call Trace: [<002c5d3e>] pmz_console_setup+0x64/0xe4
The normal tty driver doesn't crash, because init_pmz() checks
pmz_ports_count again after calling pmz_probe().
In the serial console initialization path, pmz_console_init() doesn't do
this, causing the driver to crash later.
Add a check for pmz_ports_count to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9326b047e4 includes a typo
of "8350_core" instead of "8250_core", so correct it.
Fixes kernel bugzilla #60724:
https://bugzilla.kernel.org/show_bug.cgi?id=60724
Reported-by: Christoph Biedl <bugzilla.kernel.bpeb@manchmal.in-ulm.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull slave-dmaengine changes from Vinod Koul:
"This brings for slave dmaengine:
- Change dma notification flag to DMA_COMPLETE from DMA_SUCCESS as
dmaengine can only transfer and not verify validaty of dma
transfers
- Bunch of fixes across drivers:
- cppi41 driver fixes from Daniel
- 8 channel freescale dma engine support and updated bindings from
Hongbo
- msx-dma fixes and cleanup by Markus
- DMAengine updates from Dan:
- Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
- In the course of testing 1/ a collection of enhancements to
dmatest fell out. Notably basic performance statistics, and
fixed / enhanced test control through new module parameters
'run', 'wait', 'noverify', and 'verbose'. Thanks to Andriy and
Linus [Walleij] for their review.
- Testing the raid related corner cases of 1/ triggered bugs in
the recently added 16-source operation support in the ioatdma
driver.
- Some minor fixes / cleanups to mv_xor and ioatdma"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (99 commits)
dma: mv_xor: Fix mis-usage of mmio 'base' and 'high_base' registers
dma: mv_xor: Remove unneeded NULL address check
ioat: fix ioat3_irq_reinit
ioat: kill msix_single_vector support
raid6test: add new corner case for ioatdma driver
ioatdma: clean up sed pool kmem_cache
ioatdma: fix selection of 16 vs 8 source path
ioatdma: fix sed pool selection
ioatdma: Fix bug in selftest after removal of DMA_MEMSET.
dmatest: verbose mode
dmatest: convert to dmaengine_unmap_data
dmatest: add a 'wait' parameter
dmatest: add basic performance metrics
dmatest: add support for skipping verification and random data setup
dmatest: use pseudo random numbers
dmatest: support xor-only, or pq-only channels in tests
dmatest: restore ability to start test at module load and init
dmatest: cleanup redundant "dmatest: " prefixes
dmatest: replace stored results mechanism, with uniform messages
Revert "dmatest: append verify result to results"
...
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
Here's the big tty/serial driver update for 3.13-rc1.
There's some more minor n_tty work here, but nothing like previous
kernel releases. Also some new driver ids, driver updates for new
hardware, and other small things.
All of this has been in linux-next for a while with no issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJ6xnEACgkQMUfUDdst+ylj1QCfaIzUNuFfzTmyB6K6iZrRNhCc
WPgAnRLkkEpI/3rRo7jKwGQsuIuyybUu
=r149
-----END PGP SIGNATURE-----
Merge tag 'tty-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the big tty/serial driver update for 3.13-rc1.
There's some more minor n_tty work here, but nothing like previous
kernel releases. Also some new driver ids, driver updates for new
hardware, and other small things.
All of this has been in linux-next for a while with no issues"
* tag 'tty-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (84 commits)
serial: omap: fix missing comma
serial: sh-sci: Enable the driver on all ARM platforms
serial: mfd: Staticize local symbols
serial: omap: fix a few checkpatch warnings
serial: omap: improve RS-485 performance
mrst_max3110: fix unbalanced IRQ issue during resume
serial: omap: Add support for optional wake-up
serial: sirf: remove duplicate defines
tty: xuartps: Fix build error when COMMON_CLK is not set
tty: xuartps: Fix build error due to missing forward declaration
tty: xuartps: Fix "may be used uninitialized" build warning
serial: 8250_pci: add Pericom PCIe Serial board Support (12d8:7952/4/8) - Chip PI7C9X7952/4/8
tty: xuartps: Update copyright information
tty: xuartps: Implement suspend/resume callbacks
tty: xuartps: Dynamically adjust to input frequency changes
tty: xuartps: Updating set_baud_rate()
tty: xuartps: Force enable the UART in xuartps_console_write
tty: xuartps: support 64 byte FIFO size
tty: xuartps: Add polled mode support for xuartps
tty: xuartps: Implement BREAK detection, add SYSRQ support
...
Renesas ARM platforms are transitioning from single-platform to
multi-platform kernels using the new ARCH_SHMOBILE_MULTI. Make the
driver available on all ARM platforms to enable it on both ARCH_SHMOBILE
and ARCH_SHMOBILE_MULTI, and increase build testing coverage with
COMPILE_TEST.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These local symbols are used only in this file.
Fix the following sparse warnings:
drivers/tty/serial/mfd.c:296:6: warning: symbol 'hsu_dma_tx' was not declared. Should it be static?
drivers/tty/serial/mfd.c:343:6: warning: symbol 'hsu_dma_start_rx_chan' was not declared. Should it be static?
drivers/tty/serial/mfd.c:389:6: warning: symbol 'hsu_dma_rx' was not declared. Should it be static?
drivers/tty/serial/mfd.c:1186:17: warning: symbol 'serial_hsu_pops' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If RS-485 is enabled, make the OMAP UART fire THR interrupts when both
TX FIFO and TX shift register are empty instead of polling the
equivalent status bit. This removes the burst of interrupt requests
seen at every end of transmission.
Also: the comment said that the TX FIFO trigger level was set at 16
characters when it's 32 in reality.
Signed-off-by: Philippe Proulx <philippe.proulx@savoirfairelinux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During resume, a startup will request_irq again, meantime resume function's
enable_irq will cause unbalanced IRQ issue.
Fix this issue by moving request_irq to probe function.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Chen, Jie <jie.d.chen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the recent pinctrl-single changes, omaps can treat
wake-up events from deeper idle states as interrupts.
There's a separate "io chain" controller on most omaps
that stays enabled when the device hits off-idle and the
regular interrupt controller is powered off.
Let's add support for the optional second interrupt for
wake-up events. And then serial-omap can manage the
wake-up interrupt from it's runtime PM calls to avoid
spurious interrupts during runtime.
Note that the wake interrupt is board specific as it
uses the UART RX pin, and for omap3, there are six pin
options for UART3 RX pin.
Also Note that the legacy platform based booting handles
the wake-ups in the legacy mux driver and does not need to
pass the wake-up interrupt to the driver.
And finally, to pass the wake-up interrupt in the dts file,
either interrupt-map or the pending interrupts-extended
property needs to be passed. It's probably best to use
interrupts-extended when it's available.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes duplicate defines in drivers/tty/serial/sirfsoc_uart.h
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clock notifiers are only available when CONFIG_COMMON_CLK is enabled.
Hence all notifier related code has to be protected by corresponsing
ifdefs.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_PM_SLEEP is enabled and CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
is not, a forward declaration of the uart_driver struct is not
included, leading to a build error due to an undeclared variable.
Fixing this by moving the definition of the struct uart_driver before
the definition of the suspend/resume callbacks.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialize varibles for which a 'may be used uninitalized' warning is
issued.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace some instances of of_irq_map_one()/irq_create_of_mapping() and
of_irq_to_resource() by the simpler equivalent irq_of_parse_and_map().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
[grant.likely: resolved conflicts with core code renames]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Implement suspend and resume callbacks in order to support system
suspend/hibernation.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a clock notifier to dynamically handle frequency changes of the
input clock by reprogramming the UART in order to keep the baud rate
constant.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original algorithm to find the best baud rate dividers does not necessarily
find the best set of dividers. And in the worst case may even write illegal
values to the hardware.
The new function should make better use of the hardware capabilities and be able
to provide valid settings for a wider range of baud rates and also input clocks.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible that under certain circumstances xuartps_console_write is entered
while the UART disabled. When this happens the code will busy loop in
xuartps_console_putchar, since the character is never written and the TXEMPTY
flag is never set. The result is a system lockup. This patch force enables the
UART for the duration of xuartps_console_write to avoid this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes to use the 64 byte FIFO depth and fix the issue
by clearing the txempty interrupt in isr status for tx
after filling in data in start_tx function
Signed-off-by: Suneel Garapati <suneelg@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cadence UART does not do break detection, even if the
datasheet says it does. This patch adds break detection in
software (tested in 8N1 mode only) and enables SYSRQ,
allowing for Break-g to enter KDB and all the other goodies.
Signed-off-by: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On older SoC, the "name" field is not filled in the register map.
Fix the way to figure out if the serial port is an uart or an usart for these
older products (with corresponding properties).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 055560b04a (serial: at91:
distinguish usart and uart) the older products which do not have a
name field in their register map are unable to use their serial output.
As the main console output is usually the serial interface (aka DBGU) it
is pretty unfortunate.
So, instead of failing during probe() we just silently configure the serial
peripheral as an uart. It allows us to use these serial outputs.
The proper solution is proposed in another patch.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 055560b04a (serial: at91:
distinguish usart and uart) the older products which do not have a
name field in their register map are unable to use their serial output.
As the main console output is usually the serial interface (aka DBGU) it
is pretty unfortunate.
So, instead of failing during probe() we just silently configure the serial
peripheral as an uart. It allows us to use these serial outputs.
The proper solution is proposed in another patch.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for Fintek's 4, 8, and 12 port PCIE serial cards.
Thanks to Fintek for the sample devices, and the spec needed in order to
implement this.
Cc: Amanda Ying <amanda_ying@fintek.com.tw>
Cc: Felix Shih <felix_shih@fintek.com.tw>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I worried that the delay of the sdma_run_channel0() maybe too long for
interrupt context, so I added the workqueues for RX/TX DMA.
But tested with bluetooth device, I find that the delay of sdma_run_channel0()
is about 8us (tested in imx6dl sabreauto board). I think the delay
is acceptable.
This patch removes the RX/TX workqueues for DMA, it makes the
code more clear.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to missing braces on an if statement, in presence of a device_node a
port was always assigned -1, regardless of any alias entries in the
device tree. Conversely, if device_node was NULL, an unitialized port
ended up being used.
This patch adds the missing braces, fixing the issues.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the dmaengine_tx_status to simplify the code, do not change any logic.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the (xmit->tail > xmit->head) is true and the xmit->head is 0,
we only need one DMA scatterlist in actually. Current code uses two DMA
scatterlists in this case, this is obviously wrong.
This patch fixes it.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Assume the following situation:
If the DMA is enabled, and the a TX DMA operation is working,
But we have not issued the TX DMA operation (or we have issued the
TX DMA operation with dma_async_issue_pending(), but the DMA has not
started to move the data from the memory to the TXFIFO).
At this time, we may get the wrong status of the transmitter when we
call the imx_tx_empty. In such situation, only check the USR2_TXDC
does not enough for us.
This patch checks the DMA's situation, and return 0 when the TX DMA is
working.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver does not implement the flush_buffer hook for
uart_ops. When we enable the DMA for the driver, and test it with Bluetooth,
we may meet the following bug for TX:
[1] User application may call the flush operation at any time.
The uart_flush_buffer() calls the uart_circ_clear() to set
the xmit->head and xmit->tail with 0.
[2] The TX DMA callback can be called at any time too.
The dma_tx_call() will update the xmit->tail.
If [2] occurs just after the [1], we will get the wrong xmit->tail.
This patch implements the flush_buffer hook to fix this issue.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This callback is gone and not coming back, so will not be
supported later.
Cc: Johan Hovold <jhovold@gmail.com>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This callback is gone and not coming back, so will not be
supported later.
Cc: Gerhard Sittig <gsi@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This callback is unused by the serial core since pre-git days
and is not coming back. Delete it. Enabling wakeup on the
SA1100 platforms should be done in the suspend() callback
so the platform hook is left in the serial port struct for
later enablement.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This callback is unused by the serial core since pre-git days
and is not coming back. Delete it. Enabling wakeup on the
OMAP serial driver is done through other runpaths these days.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These aren't necessary after switch and while blocks.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race between termios configuration and xmit that can cause the
intel_mid_ssp_spi driver to stall.
Serializing spi transactions fixes the problem.
Signed-off-by: Bin Gao <bin.gao@intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should check the validity of the irq number before calling
disable_irq() and enable_irq() in the suspend/resume function,
as "max->irq == 0" means the irq is not enabled for max3110
device, otherwise it will hurt device whose irq number is really 0.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add calls to clk_prepare and unprepare so that EMMA Mobile EV2 can
migrate to the common clock framework.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
[takashi.yoshii.ze@renesas.com: edited for conflicts]
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
This reverts commit f7d2c0bbdb, as it
causes build errors when the driver is built as a module.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DMA is enabled (with hardware flow control enabled) the FIFO size
must be set to the size of the DMA buffer, as this is the size the tty
subsystem can use.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver core clears the driver data to NULL after device_release
or on probe failure, so just remove it from here.
Driver core change:
"device-core: Ensure drvdata = NULL when no driver is bound"
(sha1: 0998d06310)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When configured with UART_16550_COMPATIBLE=NO or in versions prior to
the introduction of this option, the Designware UART will ignore writes
to the LCR if the UART is busy. The current workaround saves a copy of
the last written LCR and re-writes it in the ISR for a special interrupt
that is raised when a write was ignored.
Unfortunately, interrupts are typically disabled prior to performing a
sequence of register writes that include the LCR so the point at which
the retry occurs is too late. An example is serial8250_do_set_termios()
where an ignored LCR write results in the baud divisor not being set and
instead a garbage character is sent out the transmitter.
Furthermore, since serial_port_out() offers no way to indicate failure,
a serious effort must be made to ensure that the LCR is actually updated
before returning back to the caller. This is difficult, however, as a
UART that was busy during the first attempt is likely to still be busy
when a subsequent attempt is made unless some extra action is taken.
This updated workaround reads back the LCR after each write to confirm
that the new value was accepted by the hardware. Should the hardware
ignore a write, the TX/RX FIFOs are cleared and the receive buffer read
before attempting to rewrite the LCR out of the hope that doing so will
force the UART into an idle state. While this may seem unnecessarily
aggressive, writes to the LCR are used to change the baud rate, parity,
stop bit, or data length so the data that may be lost is likely not
important. Admittedly, this is far from ideal but it seems to be the
best that can be done given the hardware limitations.
Lastly, the revised workaround doesn't touch the LCR in the ISR, so it
avoids the possibility of a "serial8250: too much work for irq" lock up.
This problem is rare in real situations but can be reproduced easily by
wiring up two UARTs and running the following commands.
# stty -F /dev/ttyS1 echo
# stty -F /dev/ttyS2 echo
# cat /dev/ttyS1 &
[1] 375
# echo asdf > /dev/ttyS1
asdf
[ 27.700000] serial8250: too much work for irq96
[ 27.700000] serial8250: too much work for irq96
[ 27.710000] serial8250: too much work for irq96
[ 27.710000] serial8250: too much work for irq96
[ 27.720000] serial8250: too much work for irq96
[ 27.720000] serial8250: too much work for irq96
[ 27.730000] serial8250: too much work for irq96
[ 27.730000] serial8250: too much work for irq96
[ 27.740000] serial8250: too much work for irq96
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the printk() calls to to dev_*() instead, to tie into the dynamic
debugging infrastructure.
Also change some "raw" printk() calls to dev_err() to provide a better
error message to userspace so it can properly identify the device and
not just have to guess.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stub for dw8250_probe_acpi() is missing an argument.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel BayTrail has two HS-UARTs with 64 byte fifo, support
for DMA and support for 16750 compatible Auto Flow Control.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The nice thing about devm_* is that the driver doesn't need to free the
resources but the driver core takes care about that.
These calls were introduced in commit c08f015 (serial: clps711x: Using
CPU clock subsystem for getting base UART speed).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing uart_unregister_driver() before return
from sccnxp_probe() in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make Mode16 more preferred than Mode13, to match TRM baudrates table.
Signed-off-by: Alexey Pelykh <alexey.pelykh@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Laurent Pinchart