Causes the PCI stack to complain, and then eventually call the
PCI remove function, which ipw2100 is not expecting. It then
tries to unregister an already-released netdev and other nasty
things, leading to a panic.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1185518
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in mwifiex_dbg debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in aggr_ctrl module parameter
message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tdls uapsd support capability is default disabled during
tdls setup, correspondingly it should also been disabled
in tdls config.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Zhiyuan Yang <yangzy@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We need to unlock if mwifiex_usb_prepare_tx_aggr_skb() fails.
Fixes: a2ca85ad72 ("mwifiex: usb: add timer to flush aggregation packets")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We inited wakeup info at the beginning of mwifiex_add_card, so we need
to uninit it in the error handling.
It's much the same as what we did in:
36908c4 mwifiex: uninit wakeup info when removing device
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We got a compile warning shows below:
drivers/net/wireless/marvell/mwifiex/sdio.c: In function
'mwifiex_sdio_remove':
drivers/net/wireless/marvell/mwifiex/sdio.c:377:6: warning: variable
'ret' set but not used [-Wunused-but-set-variable]
Per the code, it didn't check if mwifiex_sdio_read_fw_status
finish successfully. We should at least check the return of
mwifiex_sdio_read_fw_status, otherwise the following check of
firmware_stat and adapter->mfg_mode is pointless as the device
is probably dead.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This print isn't very useful. It's also different between
mwifiex_add_card() and mwifiex_reinit_sw(), and I'd like to consolidate
them eventually.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It has some scary comments about "only being called" from the timeout
handler, so let's help keep it that way.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'card->dev' is initialized once and is never cleared. Drop the
unnecessary "safety" check, as it simply obscures things, and we don't
do this check everywhere (and therefore it's not really "safe").
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In testing the mwifiex reset code path, I've noticed KASAN complaining
about some "overwritten poison values" in our RX buffer descriptors.
Because KASAN didn't notice this at the time of a CPU write, this seems
to suggest that the device is writing to this memory.
This makes a little sense, because when resetting, we don't necessarily
expect the device to be responsive, so we don't have a chance to disable
everything cleanly.
We can at least take the precaution of disabling DMA for the device
though, and in my testing that seems to clear up this particular issue.
This patch reorders the removal path so that we disable the device
*before* releasing our last PCIe buffers, and it clears/sets the bus
master feature from the PCI device when resetting.
Along the way, remove the insufficient (and confusing) error path in
mwifiex_pcie_up_dev() (it doesn't unwind things well enough, and it
doesn't propagate its errors upward anyway).
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The card_reset() implementation should be setting our state flags and
cancelling commands for us (i.e., in mwifiex_shutdown_drv()), so let's
not do it here.
Also, this debugfs file is useful for testing and debugging the reset
feature, so we shouldn't do extra preparatory steps here, as that might
cause different reset behavior, which could either cause new bugs or
paper over existing ones that this debug feature should otherwise help
us catch.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After removing the interrupt loop in commit 5d5ddb5e0d ("mwifiex:
pcie: don't loop/retry interrupt status checks"), there is practically
zero difference between mwifiex_process_pcie_int() (which handled legacy
PCI interrupts and MSI interrupts) and mwifiex_process_msix_int() (which
handled MSI-X interrupts). Let's add the one relevant line to
mwifiex_process_pcie_int() and kill the copy-and-paste.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After removing the interrupt loop in commit 5d5ddb5e0d ("mwifiex:
pcie: don't loop/retry interrupt status checks"), we don't need to keep
track of the cleared interrupts (actually, we didn't need to do that
before, but we *really* don't need to now).
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's always called with 'true' -- we only determine it 'false' locally
within this function. So drop the parameter.
Also, this should be 'bool' (since we use true/false), not 'u32'.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Despite the name (and meticulous comments), this function frees no
memory and does not touch any locks. All it does is "delete" the list
heads -- which just means they'll be dangling, and we'll need to re-init
them if we use them again.
It seems like this code would work OK as a sort of canary for using the
list after we've torn everything down, so it's fine to keep the code;
let's just get the name and comments to match what's actually happening.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The .idle_time field *should* be unused, but technically, we're allowing
unitialized stack garbage to pass all the way through to the firmware
host command. Let's zero it out instead.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In reading through _mwifiex_fw_dpc(), I noticed that after we've
registered our wiphy, we still have error paths that don't free it back
up. Let's do that.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we leave the delete interface function, there are still netdev
hooks that might try to process the device. We're short-circuiting some
of that by changing the interface type and clearing ieee80211_ptr. This
means we skip NETDEV_UNREGISTER_FINAL in cfg80211. Fortunately, that is
currently a no-op.
We don't need most of the cleanup here anyway:
* the connection state will get (un)set as part of the disconnect
process (which cfg80211 already initiates for us)
* the interface type doesn't actually need to be cleared at all (it'll
trigger a WARN_ON() in cfg80211 if we do)
* the iee80211_ptr isn't really "ours" to clear anyway
So stop resetting those 3 things.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's possible for some control interfaces (e.g., scans, set freq) to be
active after we've stopped our main work queue and the netif TX queues.
These don't get completely shut out until we've unregistered the wdevs
and wiphy.
So let's only free command buffers and poison our lists after
wiphy_unregister().
This resolves various use-after-free issues seen when resetting the
device.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In general, it's helpful to use the same code for device removal as for
device reset, as this tends to have fewer bugs. Let's move the wiphy
unregistration code into the common reset and removal code.
In particular, it's very hard to properly handle the reset sequence when
something fails. Currently, if mwifiex_reinit_sw() fails, we've failed
to unregister the associated wiphy, and so running something as simple
as "iw phy" can trigger an OOPS, as the wiphy still has hooks back into
freed mwifiex data structures. For example, KASAN complained:
[... see reset fail for other reasons ...]
[ 1184.821158] mwifiex_pcie 0000:01:00.0: info: dnld wifi firmware from 174948 bytes
[ 1186.870914] mwifiex_pcie 0000:01:00.0: info: FW download over, size 608396 bytes
[ 1187.685990] mwifiex_pcie 0000:01:00.0: WLAN FW is active
[ 1187.692673] mwifiex_pcie 0000:01:00.0: cmd_wait_q terminated: -512
[ 1187.699075] mwifiex_pcie 0000:01:00.0: info: _mwifiex_fw_dpc: unregister device
[ 1187.713476] mwifiex: Failed to bring up adapter: -5
[ 1187.718644] mwifiex_pcie 0000:01:00.0: reinit failed: -5
[... run `iw phy` ...]
[ 1212.902419] ==================================================================
[ 1212.909806] BUG: KASAN: use-after-free in mwifiex_cfg80211_get_antenna+0x54/0xfc [mwifiex] at addr ffffffc0ad1a8028
[ 1212.920246] Read of size 1 by task iw/3127
[...]
[ 1212.934946] page dumped because: kasan: bad access detected
[...]
[ 1212.950665] Call trace:
[ 1212.953148] [<ffffffc00020a69c>] dump_backtrace+0x0/0x190
[ 1212.958572] [<ffffffc00020a96c>] show_stack+0x20/0x28
[ 1212.963648] [<ffffffc0005ce18c>] dump_stack+0xa4/0xcc
[ 1212.968723] [<ffffffc0003c4430>] kasan_report+0x378/0x500
[ 1212.974140] [<ffffffc0003c3358>] __asan_load1+0x44/0x4c
[ 1212.979462] [<ffffffbffc2e8360>] mwifiex_cfg80211_get_antenna+0x54/0xfc [mwifiex]
[ 1212.987131] [<ffffffbffc084fc4>] nl80211_send_wiphy+0x75c/0x2de0 [cfg80211]
[ 1212.994246] [<ffffffbffc094f60>] nl80211_dump_wiphy+0x32c/0x438 [cfg80211]
[ 1213.001149] [<ffffffc000ab6404>] genl_lock_dumpit+0x48/0x64
[ 1213.006746] [<ffffffc000ab3474>] netlink_dump+0x178/0x398
[ 1213.012171] [<ffffffc000ab3d18>] __netlink_dump_start+0x1bc/0x260
[...]
This all goes away if we just tear down the wiphy on the way down, and
set it back up if/when we bring the device back up.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rogue cases (due to other bugs) it's possible we try to process an
old command response *after* resetting the device. This could trigger a
double-free (or the SKB can get reallocated elsewhere...causing other
memory corruptions) in mwifiex_pcie_process_cmd_complete().
For safety (and symmetry) let's always NULL out the command buffer as we
free it up. We're already doing this for the command response buffer.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When resetting the device, we might have queued up interrupts that
didn't get a chance to finish processing. We really don't need to handle
them at this point; we just want to make sure they don't cause us to try
to process old commands from before the device was reset.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When PCIe FLR code was added, it explicitly copy-and-pasted much of
mwifiex_remove_card() into mwifiex_shutdown_sw(). This is unnecessary,
as almost all of the code should be reused.
Let's reunite what we can for now.
The only functional changes for now:
* call netif_device_detach() in the remove() code path -- this wasn't
done before, but it really should be a no-op, when the device is
getting totally unregistered soon anyway
* call the ->down_dev() driver callback only after we've finished all
SW teardown -- this should have no significant effect, since the only
user (pcie.c) does very minimal work there, and it doesn't matter
that we reorder this
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
u32 pointer is changed to u16 and filled the value. Problem is
solved by using local temporary variable. Below static checker
warning was reported.
drivers/net/wireless/rsi/rsi_91x_usb.c:400 rsi_usb_master_reg_read()
warn: passing casted pointer 'value' to 'rsi_usb_reg_read()'
32 vs 16.
Fixes: b97e9b94ad ("rsi: Add new host interface operations")
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These checks are required. Otherwise we may end up getting
memory corruption if invalid length is passed.
Fixes: b97e9b94ad ("rsi: Add new host interface operations")
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
4 bytes is fixed size for reading or writing USB register. We
will use a macro instead of hardcoding this.
Fixes: b97e9b94ad ("rsi: Add new host interface operations")
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Below regulatory changes are included this patch
* Country code is saved as it will be used in bgscan.
* Region codes are mapped according to RSI region codes.
* Radar flag settings are moved under the check if 5GHZ band
is enabled.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When interface is down it is better to stop all RX packets to
host. 0xffff will block all packets to host.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Device specific descriptor for each TX packet is prepared on top of
skb data address. This descriptor should be pulled out before
indicating the TX status to mac80211.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TX command frame block/unblock data is modified to
use common descriptor structure.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Data queues should be unblocked after station add notify frame
is sent and should be blocked after station delete notify is sent.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When Short Gaurd Interval is enabled bit 9 is set in rate. Otherwise
it should not be set. Added missing 'else' case in this patch.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Broadcast bit to be set for broadcast and multicast packets.
For remove_key, tx and rx mic need not be filled.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TX command frame set_key is modified to use common descriptor
structure.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
VAP capablities frame configured to device is modified to use
common descriptor structure.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TX command frame set_channel is modified to use common
descriptor structure. Also DFS channel indication to firmware
is added in the descriptor for dfs channels configuration.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Baseband RF programming frame configured to device is modified
to use common descriptor structure.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AMPDU aggregation parameters frame configured to device is
modified to use common descriptor structure.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TX command frame peer notify is updated to use common descriptor
structure. MPDU density value added to the frame.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function rsi_mgmt_pkt_to_core() is for passing the 802.11
management frames to mac80211. So, it is unnecessary to check
again for the frame type 802.11 management in this function.
It can be checked before passing to this function.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Radio capabilities frame is updated to use common descriptor
structure. Also, few changes to this frame is done like hardware
queues are increase to 12 from 8, default channel number is included.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For all TX command packets immediate wakeup bit needs to be
set in descriptor. This will make sure device will wakeup if it
is in any sleep state. Priority of the packet is also set.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All internal management packets (command packets) use some common
fields and some packet specific fields for packet descriptors.
This patch adds some common structures which are needed for all
command packets.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We have now added separate lock for Rx. This lock is used to protect
tx path only
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Deadlock issue is observed during our stress tests. The root
cause for the issue is same lock is used between tx and rx threads.
This patch adds a separate mutex lock for rx thread to resolve
the problem.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer firmware sends information about number of blocks through
interrupt only. We don't need to read extra register for this.
This patch adds needed driver changes for this enhancment. The
change here is backward compatible
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dan Williams