The internal, driver-specific maintenance of sequence
numbers is applicable only for HT frames.
Also, remove comments that are not relevant anymore.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix typo. The index should be multiplied by the entry size, not 'and'-ed.
Found via code-inspection.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices have 40MHz operation disabled entirely. Ensure that driver do
not enable 40MHz operation if a channel does not allow this.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2135
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent powersaving work resulted in power management ops being called
during EEPROM initialization. The lock used by these functions is not
initialized at this time. Ensure lock is initialized before it is used.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we see from http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2125
that power saving does not work well on 3945. Since then power saving has
also been connected with association problems where an AP deathenticates a
3945 after it is unable to transmit data to it - this happens when 3945
enters power savings mode.
Disable power save support until issues are resolved.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I've also for a long time had a problem with the
temperature calculation code, which I had fixed
by byte-swapping the values, and now it turns out
that was the correct fix after all.
Also, any use of iwl_eeprom_query_addr() that is
for more than a u8 must be cast to little endian,
and some structs as well.
Fix all this. Again, no real impact on platforms
that already are little endian.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The construct "le16_to_cpu((__force __le16)(r >> 16))" has
always bothered me when looking through the iwlwifi code,
it shouldn't be necessary to __force anything, and before
this code, "r" was obtained with an ioread32, which swaps
each of the two u16 values in it properly when swapping the
entire u32 value. I've had arguments about this code with
people before, but always conceded they were right because
removing it only made things not work at all on big endian
platforms.
However, analysing a failure of the OTP reading code, I now
finally figured out what is going on, and why my intuition
about that code being wrong was right all along.
It turns out that the 'priv->eeprom' u8 array really wants
to have the data in it in little endian. So the force code
above and all really converts *to* little endian, not from
it. Cf., for instance, the function iwl_eeprom_query16() --
it reads two u8 values and combines them into a u16, in a
little-endian way. And considering it more, it makes sense
to have the eeprom array as on the device, after all not
all values really are 16-bit values, the MAC address for
instance is not.
Now, what this really means is that all the annotations are
completely wrong. The eeprom reading code should fill the
priv->eeprom array as a __le16 array, with __le16 values.
This also means that iwl_read_otp_word() should really have
a __le16 pointer as the data argument, since it should be
filling that in a format suitable for priv->eeprom.
Propagating these changes throughout, iwl_find_otp_image()
is found to be, now obviously visible, defective -- it uses
the data returned by iwl_read_otp_word() directly as if it
was CPU endianness. Fixing that, which is this hunk of the
patch:
- next_link_addr = link_value * sizeof(u16);
+ next_link_addr = le16_to_cpu(link_value) * sizeof(u16);
is the only real change of this patch. Everything else is
just fixing the sparse annotations.
Also, the bug only shows up on big endian platforms with a
1000 series card. 5000 and previous series do not use OTP,
and 6000 series has shadow RAM support which means we don't
ever use the defective code on any cards but 1000.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've had many reports of rt61pci failures with powersaving enabled.
Therefore, as a stop-gap measure, disable powersaving of the rt61pci
until we have found a proper solution.
Also disable powersaving on rt2800pci as it most probably will show
the same problem.
Cc: stable@kernel.org
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sizeof(iv16) and sizeof(iv32) are the sizes of pointers. Change them to
the size of the copied data.
Furthermore, iveiv_entry is a local structure that has just been
initialized and is not visible outside this function. Thus, there would
seem to be no point to copy data into it. The order of the arguments is
thus changed to copy the data into the parameters, which are provided as
pointers, suggesting in this case that they should be used to return values.
A simplified version of the semantic patch that finds the first problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
First, we copy/paste the padding stuff from ath9k_tx to ath_tx_cabq since it
needs to same kind of padding, but for internally generated beacons.
Next, software padding done on TX needs to be removed before calling
ieee80211_tx_status. The code was already there in ath_tx_complete but it
was wrong. Fix it by using ath9k_cmn_padpos. This later code has been
tested by sending packets to a monitor interface and reading packets from the
same interface.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When trigger event log dumping from debugfs, the entire event log
should be dumped and the size should match the number of events being
dump.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent commits "iwlwifi: remove power-wasting calls to apm_ops.init()" and
"iwlagn: power up device before initializing EEPROM" had the goal of
reducing device power consumption from the time the module is loaded until
the interface is brought up and the device's power saving mechanisms kick
in. The idea is that once the module is loaded there is no need for the
device to consume power until the interface is brought up.
With the current solution the device is only powered up during EEPROM read,
and then so also only if the EEPROM type is OTP. We have found that on
certain platforms even non-OTP devices require power to be up during EEPROM
read. On these platforms the driver never loads and the system log contains
the following:
iwlagn 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0x080403D8
We thus now power up all devices during EEPROM read.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In iwlwifi, priv->alloc_rxb_page is used to keep track of the Rx
pages allocated by the driver. This cleans up the page free routines
by introducing __iwl_free_pages/iwl_free_pages so that the accounting
is more accurate and less error prone. This also fixes two instances where
the counter was not updated.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The error was introduced while merging:
commit 4529819c45
bnx2: reset_task is crashing the kernel. Fixing it.
Signed-off-by: Michael Chan <mchan@broadcom.com>k
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the per rx/tx queue stats.
To update the per rx queue stats a new structure has been
introduced rx_q_stats.
The per tx queue stats are updated via the netdev_queue
structure itself.
Note that we update only the tx_packtes, tx_bytes, rx_packets,
rx_bytes and rx_dropped stats on a per queue basis.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to enable filer whenever we need to use multiple RX
queues. Also, need to program RIR0 register with the required
distribution we require, if using RX filer hashing support for
packet distribution to multiple queues.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running the following script on an active bnx2 interface:
while(true); do ifconfig ethX mtu 9000; ifconfig ethX mtu 1500; done
A timeout error appears and dumps the following stack:
NETDEV WATCHDOG: eth4 (bnx2): transmit queue 0 timed out
------------[ cut here ]------------
Badness at net/sched/sch_generic.c:261
<snip>
This patch just fixes the way that ->trans_start is refreshed.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_get_irq returns -ENXIO on failure, so !irq was probably
always true. Better use (int)irq <= 0. Note that a return value of
zero is still handled as error even though this could mean irq0.
This is a followup to 305b3228f9 that
changed the return value of platform_get_irq from 0 to -ENXIO on error.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bnx2 schedules a reset via the reset_task, e.g., due to a TX
timeout, it's possible for the NIC to be disabled with packets
pending for transmit. In this case, napi_disable will loop forever,
eventually crashing the kernel. This patch moves the disable of
the device to after the napi_disable call.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a typo in "if condition" checking for validity of MDIO
bus frequency passed as part of platform data. Bitwise AND was
being used instead of a Logical AND.
Tested on: DM6467 EVM
Signed-off-by: Nageswari Srinivasan <nageswari@ti.com>
Acked-by: Anant Gole <anantgole@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Stern noticed that e100 caused slab corruption.
commit 98468efddb changed
the allocation of cbs to use dma pools that don't return zeroed memory,
especially the cb->status field used to track which cb to clean, causing
(the visible) double freeing of skbs and a wrong free cbs count.
Now the cbs are explicitly zeroed at allocation time.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Roger Oksanen <roger.oksanen@cs.helsinki.fi>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If not signed read errors are ignored.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not override the customizable LED configuration set in the EEPROM.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netxen driver is doing this bogus thing to create a control file.
This fails if device doesn't exist, and overall is a bad way to do
the module parameter. Rather than fix borked code, just rewrite.
Just using a writeable module parameter of 0/1 is the correct way
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (71 commits)
MIPS: Lasat: Fix botched changes to sysctl code.
RTC: rtc-cmos.c: Fix warning on MIPS
MIPS: Cleanup random differences beween lmo and Linus' kernel.
MIPS: No longer hardwire CONFIG_EMBEDDED to y
MIPS: Fix and enhance built-in kernel command line
MIPS: eXcite: Remove platform.
MIPS: Loongson: Cleanups of serial port support
MIPS: Lemote 2F: Suspend CS5536 MFGPT Timer
MIPS: Excite: move iodev_remove to .devexit.text
MIPS: Lasat: Convert to proc_fops / seq_file
MIPS: Cleanup signal code initialization
MIPS: Modularize COP2 handling
MIPS: Move EARLY_PRINTK to Kconfig.debug
MIPS: Yeeloong 2F: Cleanup reset logic using the new ec_write function
MIPS: Yeeloong 2F: Add LID open event as the wakeup event
MIPS: Yeeloong 2F: Add basic EC operations
MIPS: Move several variables from .bss to .init.data
MIPS: Tracing: Make function graph tracer work with -mmcount-ra-address
MIPS: Tracing: Reserve $12(t0) for mcount-ra-address of gcc 4.5
MIPS: Tracing: Make ftrace for MIPS work without -fno-omit-frame-pointer
...
* 'for-33' of git://repo.or.cz/linux-kbuild: (29 commits)
net: fix for utsrelease.h moving to generated
gen_init_cpio: fixed fwrite warning
kbuild: fix make clean after mismerge
kbuild: generate modules.builtin
genksyms: properly consider EXPORT_UNUSED_SYMBOL{,_GPL}()
score: add asm/asm-offsets.h wrapper
unifdef: update to upstream revision 1.190
kbuild: specify absolute paths for cscope
kbuild: create include/generated in silentoldconfig
scripts/package: deb-pkg: use fakeroot if available
scripts/package: add KBUILD_PKG_ROOTCMD variable
scripts/package: tar-pkg: use tar --owner=root
Kbuild: clean up marker
net: add net_tstamp.h to headers_install
kbuild: move utsrelease.h to include/generated
kbuild: move autoconf.h to include/generated
drop explicit include of autoconf.h
kbuild: move compile.h to include/generated
kbuild: drop include/asm
kbuild: do not check for include/asm-$ARCH
...
Fixed non-conflicting clean merge of modpost.c as per comments from
Stephen Rothwell (modpost.c had grown an include of linux/autoconf.h
that needed to be changed to generated/autoconf.h)
The Octeon MGMT Ethernet ports are present in some members of the
Octeon SOC family (cn52XX and cn56XX have them).
The mdio bus connected to the MGMT PHYs is shared with the main
octeon-ethernet driver, we force it to be loaded first by calling
octeon_mdiobus_force_mod_depencency. The platform devices for the
MGMT Ethernet ports are added in
arch/mips/cavium-octeon/octeon-platform.c, and the register
definitions for the ports live in arch/mips/include/asm/octeon/ along
with their ilk.
Although it currently is the only driver in drivers/net/octeon, the
directory was created looking forward to the day that octeon-ethernet
will move there from its current home in drivers/staging.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Octeon SOC has two types of Ethernet ports, each type with its own
driver. However, the PHYs for all the ports are controlled by a
common MDIO bus. Because the mdio driver is not associated with a
particular driver, but is instead a system level resource, we create s
stand-alone driver for it.
As for the driver, we put the register definitions in
arch/mips/include/asm/octeon where most of the other Octeon register
definitions live. This is a platform driver with the platform device
for "mdio-octeon" being registered in the platform startup code.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
net: sh_eth alignment fix for sh7724 using NET_IP_ALIGN V2
ixgbe: allow tx of pre-formatted vlan tagged packets
ixgbe: Fix 82598 premature copper PHY link indicatation
ixgbe: Fix tx_restart_queue/non_eop_desc statistics counters
bcm63xx_enet: fix compilation failure after get_stats_count removal
packet: dont call sleeping functions while holding rcu_read_lock()
tcp: Revert per-route SACK/DSACK/TIMESTAMP changes.
ipvs: zero usvc and udest
netfilter: fix crashes in bridge netfilter caused by fragment jumps
ipv6: reassembly: use seperate reassembly queues for conntrack and local delivery
sky2: leave PCI config space writeable
sky2: print Optima chip name
x25: Update maintainer.
ipvs: fix synchronization on connection close
netfilter: xtables: document minimal required version
drivers/net/bonding/: : use pr_fmt
can: CAN_MCP251X should depend on HAS_DMA
drivers/net/usb: Correct code taking the size of a pointer
drivers/net/cpmac.c: Correct code taking the size of a pointer
drivers/net/sfc: Correct code taking the size of a pointer
...
Fix sh_eth for sh7724 by adding NET_IP_ALIGN support V2.
Without this patch the receive data is misaligned.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the 82598 is fed 802.1q packets, it chokes with
an error of the form:
ixgbe: eth0: ixgbe_tx_csum: partial checksum but proto=81!
As the logic there was not smart enough to look into
the vlan header to pick out the encapsulated protocol.
There are times when we'd like to send these packets
out without having to configure a vlan on the interface.
Here we check for the vlan tag and allow the packet to
go out with the correct hardware checksum.
This patch is a clone of a previously submitted patch by
Arthur Jones <ajones@riverbed.com> for igb (Commit -
fa4a7ef36e).
Signed-off-by: Gurucharan Shetty <gshetty@riverbed.com>
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modified patch with Dave's comments to replace mdelay with proper msleep.
Fix 82598 copper link issue, where the phy prematurely indicates link
before it is ready to process packets. The new function looks for phy
link and indicates that, when it is available. If phy is not ready
within few seconds of MAC indicating link, the function will return
failure which translates to link down indication.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the restart_queue and non_eop_desc counters from being
double-counted. They are cumulative in each ring, so we don't want to
add them to the cumulative result in the adapter's master counter.
Otherwise, the stats will be inaccurate
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts bcm63xx_enet to uset get_sset_count
like the other drivers do.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since power management is done by PCI subsystem as well as driver,
don't toggle the bit that disables PCI register writes.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Off by one in name lookup makes Optima display as (chip 0xbc)
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt2800lib incorrectly detected whether RT2800USB was enabled because
it didn't account for a modularized RT2800USB driver.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (34 commits)
m68k: rename global variable vmalloc_end to m68k_vmalloc_end
percpu: add missing per_cpu_ptr_to_phys() definition for UP
percpu: Fix kdump failure if booted with percpu_alloc=page
percpu: make misc percpu symbols unique
percpu: make percpu symbols in ia64 unique
percpu: make percpu symbols in powerpc unique
percpu: make percpu symbols in x86 unique
percpu: make percpu symbols in xen unique
percpu: make percpu symbols in cpufreq unique
percpu: make percpu symbols in oprofile unique
percpu: make percpu symbols in tracer unique
percpu: make percpu symbols under kernel/ and mm/ unique
percpu: remove some sparse warnings
percpu: make alloc_percpu() handle array types
vmalloc: fix use of non-existent percpu variable in put_cpu_var()
this_cpu: Use this_cpu_xx in trace_functions_graph.c
this_cpu: Use this_cpu_xx for ftrace
this_cpu: Use this_cpu_xx in nmi handling
this_cpu: Use this_cpu operations in RCU
this_cpu: Use this_cpu ops for VM statistics
...
Fix up trivial (famous last words) global per-cpu naming conflicts in
arch/x86/kvm/svm.c
mm/slab.c
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove DRV_NAME from pr_<level>s
Consolidate long format strings
Remove some extra tab indents
Remove some unnecessary ()s from pr_<level>s arguments
Align pr_<level> arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building for Sun 3:
drivers/net/can/mcp251x.c:1074: undefined reference to `dma_free_coherent'
drivers/net/can/mcp251x.c:976: undefined reference to `dma_alloc_coherent'
drivers/net/can/mcp251x.c:1050: undefined reference to `dma_free_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
sizeof(dev->dev_addr) is the size of a pointer. A few lines above, the
size of this field is obtained using netdev->addr_len for a call to memcpy,
so do the same here.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
sizeof(dev->dev_addr) is the size of a pointer. On the other hand,
sizeof(pdata->dev_addr) is the size of an array, so use that instead.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function efx_iterate_state contains the code
memcpy(&payload->msg, payload_msg, sizeof(payload_msg));
This is the only use of payload_msg. The type of payload_msg is
changed from a pointer to an array, so that the result of sizeof really is
the length of the string.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
3c574_cs, 3c589_cs:
disable irq before calling el3_interrupt
in the media_check function.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
A valid CAN dataframe can have a data length code (DLC) of 0 .. 8 data bytes.
When reading the CAN controllers register the 4-bit value may contain values
from 0 .. 15 which may exceed the reserved space in the socket buffer!
The ISO 11898-1 Chapter 8.4.2.3 (DLC field) says that register values > 8
should be reduced to 8 without any error reporting or frame drop.
This patch introduces a new helper macro to cast a given 4-bit data length
code (dlc) to __u8 and ensure the DLC value to be max. 8 bytes.
The different handlings in the rx path of the CAN netdevice drivers are fixed.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'ixp4xx' of git://git.kernel.org/pub/scm/linux/kernel/git/chris/linux-2.6:
IXP4xx: GTWX5715 platform only has two PCI IRQ lines, not four.
IXP4xx: Introduce IXP4XX_GPIO_IRQ(n) macro and convert IXP4xx platform files.
IXP4xx: move Gemtek GTWX5715 platform macros to the platform code.
IXP4xx: Remove unused Motorola PrPMC1100 platform macros.
IXP4xx: move FSG platform macros to the platform code.
IXP4xx: move DSM G600 platform macros to the platform code.
IXP4xx: move NAS100D platform macros to the platform code.
IXP4xx: move NSLU2 platform macros to the platform code.
IXP4xx: move Coyote platform macros to the platform code.
IXP4xx: move AVILA platform macros to the platform code.
IXP4xx: move IXDP425 platform macros to the platform code.
IXP4xx: Extend PCI MMIO indirect address space to 1 GB.
IXP4xx: Fix compilation failure with CONFIG_IXP4XX_INDIRECT_PCI.
IXP4xx: Drop "__ixp4xx_" prefix from in/out/ioread/iowrite functions for clarity.
IXP4xx: Rename indirect MMIO primitives from __ixp4xx_* to __indirect_*.
IXP4xx: Ensure index is positive in irq_to_gpio() and npe_request().
ARM: fix insl() and outsl() endianness on IXP4xx architecture.
IXP4xx: Fix normally-disabled debugging text in drivers/net/arm/ixp4xx_eth.c.
IXP4xx: change the timer base frequency to 66.666000 MHz.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (151 commits)
powerpc: Fix usage of 64-bit instruction in 32-bit altivec code
MAINTAINERS: Add PowerPC patterns
powerpc/pseries: Track previous CPPR values to correctly EOI interrupts
powerpc/pseries: Correct pseries/dlpar.c build break without CONFIG_SMP
powerpc: Make "intspec" pointers in irq_host->xlate() const
powerpc/8xx: DTLB Miss cleanup
powerpc/8xx: Remove DIRTY pte handling in DTLB Error.
powerpc/8xx: Start using dcbX instructions in various copy routines
powerpc/8xx: Restore _PAGE_WRITETHRU
powerpc/8xx: Add missing Guarded setting in DTLB Error.
powerpc/8xx: Fixup DAR from buggy dcbX instructions.
powerpc/8xx: Tag DAR with 0x00f0 to catch buggy instructions.
powerpc/8xx: Update TLB asm so it behaves as linux mm expects.
powerpc/8xx: Invalidate non present TLBs
powerpc/pseries: Serialize cpu hotplug operations during deactivate Vs deallocate
pseries/pseries: Add code to online/offline CPUs of a DLPAR node
powerpc: stop_this_cpu: remove the cpu from the online map.
powerpc/pseries: Add kernel based CPU DLPAR handling
sysfs/cpu: Add probe/release files
powerpc/pseries: Kernel DLPAR Infrastructure
...
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (75 commits)
omap3: Fix OMAP35XX_REV macros
omap: serial: fix non-empty uart fifo read abort
omap3: Zoom2/3: Update hsmmc board config params
omap3 : Enable TWL4030 Keypad for Zoom2 and Zoom3 boards
omap3: id code detection 3525 vs 3515
omap3: rx51: Use wl1251 in SPI mode 3
omap3: zoom2/3: make MMC slot work again
omap1: htcherald: Update defconfig to include mux support
omap1: LCD_DMA: Use some define rather than a hexadecimal
omap: header: remove unused data-type
omap: arch/arm/plat-omap/devices.c - sort alphabetically
omap: Correcting GPMC_CONFIG1_DEVICETYPE_NAND
OMAP3: serial - allow platforms specify which UARTs to initialize
omap3: cm-t35: add mux initialization
OMAP4: Sync up omap4430 defconfig
OMAP4: Remove the secondary wait loop
OMAP4: AuxCoreBoot registers only accessible in secure mode
OMAP4: Fix SRAM base and size
OMAP4: Fix cpu detection
omap3: pandora: board file updates for .33
...
There are certain skews of the NIC which have multiple bits set in
adapter->cap. Use & instead of == to process rx completions.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Alexander Duyck <alexander.h.duyck@intel.com>
This change makes it so that reset/interrupt storms can be avoided when
there are mailbox issues. The new behavior is to only allow the device to
trigger mailbox related resets only once every 10 seconds.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the handling of collisions between the use of the
PF/VF sides of the mailbox.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a rare use of the USB power management API which
won't be supported after the conversion to the new generic runtime power
management framework. Functionality is not altered.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all OMAP boards are using the board resources, we don't need
to keep the arch/board specific crap in the driver header.
Cc: linux-net@vger.kernel.org
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: H.J. Oertel <oe@port.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 4b77b0a2ba ("PCI: Clear
saved_state after the state has been restored"), the EEH is not
working proplery on cxgb3.
This patch fixes it, always saving the PCI state after a recovery,
in order to allow further reoveries.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prevent stale indices from causing spurious events when restarting the
bnx2x devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This step is necessary on the bnx2x devices when restarting the iSCSI
ring. Without it, the firmware can assert and cause bnx2x to report
errors.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smc_drv_resume() takes a struct device, while smc_enable_device() takes a
platform device. This fixes up the smc_enable_device() callsite with the
proper pointer.
It's not obvious when this change was introduced, as git history doesn't
go back that far. Presumably the resume code has always been broken in
this fashion.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Local flags variables will be declared whenever these functions get used,
but obviously on UP systems the flags parameter won't be touched. So add
some dummy ops that get optimized away anyways to satisfy gcc's warnings.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing TST_CFG_WRITE bits around sky2_pci_write*() in Optima
setup routines. Without the cfg-write bits, the driver may spew endless
link-up messages through qlink irq.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the TCP offload setup for Yukon-2 Optima.
It requires SKY2_HW_NE_LE flag unlike Ultra 2.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch (as1302) removes the auto_pm flag from struct usb_device.
The flag's only purpose was to distinguish between autosuspends and
external suspends, but that information is now available in the
pm_message_t argument passed to suspend methods.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From: Randy Dunlap <randy.dunlap@oracle.com>
niu drivers uses crc32 functions, so it needs to select CRC32.
niu.c:(.text+0x18a7f8): undefined reference to `crc32_le'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As shown in Kernel Bugzilla #14761, doing a controller restart after a
fatal DMA error does not accomplish anything other than consume the CPU
on an affected system. Accordingly, substitute a meaningful message for
the restart.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [2.6.32]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch reports that his rtl8187 gives warnings on suspend
("queueing ieee80211 work while going to suspend" warnings), as rtl8187
can call ieee80211_queue_delayed_work after mac80211 is suspended.
This change enhances rtl8187 led code so we can avoid queuing work after
mac80211 is suspended: now we register a radio led and make additional
checks to ensure led is off/on properly as mac80211 wants.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without this we have no gaurantee of the integrity of the
EEPROM and are likely to encounter a lot of bogus bug reports
due to actual issues on the EEPROM. With the EEPROM checksum
check in place we can easily rule those issues out.
If you run patch during a revert *you* have a card with a busted
EEPROM and only older kernel will support that concoction. This
patch is a trade off between not accepitng bogus EEPROMs and
avoiding bogus bug reports allowing developers to focus instead
on real concrete issues.
If stable keeps bogus bug reports because of a possibly busted EEPROM
feel free to apply this there too.
Tested on an AR5414
Cc: stable@kernel.org
Cc: jirislaby@gmail.com
Cc: akpm@linux-foundation.org
Cc: rjw@sisk.pl
Cc: me@bobcopeland.com
Cc: david.quan@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 46ceb60ca8 ("gianfar: Add
Multiple group Support") introduced the following build error
with CONFIG_NET_POLL_CONTROLLER=y:
CC ggianfar.o
ggianfar.c: In function 'gfar_netpoll':
ggianfar.c:2653: error: invalid storage class for function 'gfar_interrupt'
ggianfar.c:2652: warning: ISO C90 forbids mixed declarations and code
ggianfar.c:2681: error: invalid storage class for function 'adjust_link'
ggianfar.c:2764: error: invalid storage class for function 'gfar_set_multi'
ggianfar.c:2855: error: invalid storage class for function 'gfar_clear_exact_match'
ggianfar.c:2877: error: invalid storage class for function 'gfar_set_hash_for_addr'
ggianfar.c:2898: error: invalid storage class for function 'gfar_set_mac_for_addr'
ggianfar.c:2922: error: invalid storage class for function 'gfar_error'
ggianfar.c:3020: warning: ISO C90 forbids mixed declarations and code
ggianfar.c:3032: error: invalid storage class for function 'gfar_init'
ggianfar.c:3037: error: invalid storage class for function 'gfar_exit'
ggianfar.c:3041: error: initializer element is not constant
ggianfar.c:3042: error: initializer element is not constant
ggianfar.c:3042: warning: ISO C90 forbids mixed declarations and code
ggianfar.c:3042: error: expected declaration or statement at end of input
make[1]: *** [ggianfar.o] Error 1
This patch fixes the issue.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
About 50% of shutdowns of b44 Ethernet adapter ends by kernel panic
with kernels compiled with stack-protector.
Checking b44_magic_pattern() return values, one call of
b44_magic_pattern() returns 127. It means, that set_bit(128, pmask)
was called on line 1509. It means that bit 0 of 17th byte of pmask was
overwritten. But pmask has only 16 bytes. Stack corruption happens.
It seems that set_bit() on line 1509 always writes one bit off.
The fix does not only solve the stack corruption, but also makes Wake
On LAN working on my onboard B44 on Asus A7V-333X mainboard.
It seems that this problem affects all kernel versions since commit
725ad800 ([PATCH] b44: add wol for old nic) on 2006-06-20.
Signed-off-by: Stanislav Brabec <sbrabec@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
use common_task instead of reset_task and link_chg_task, so it fix "call cancel_work_sync
from the work itself".
Signed-off-by: Jie Yang <jie.yang@atheros.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add pci map direction in atl1c_buffer flags, it is used when call pci_unmap
apis.
Signed-off-by: Jie Yang <jie.yang@atheros.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unified firmware image may not contain MN type of firmware.
Driver should fall back to NOMN firmware type instead
of going to flash.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o netif_running() check for enabling interrupt at end of napi poll is
not enough to cover firmwar recovery. Instead test __NX_DEV_UP bit.
o Avoid re-entry into to netxen_nic_down() with __NX_DEV_UP bit check.
Acked-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o To prevent race conditions with other reset events.
During suspend/resume and firmware recovery, acquire rtnl_lock,
while changing interface state.
Acked-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the locking scheme on the fec_mpc52xx driver. This device can
receive IRQs from three sources; the FEC itself, the tx DMA, and the
rx DMA. Mutual exclusion was handled by taking a spin_lock() in the
critical regions, but because the handlers are run with IRQs enabled,
spin_lock() is insufficient and the driver can end up interrupting
a critical region anyway from another IRQ.
Asier Llano discovered that this occurs when an error IRQ is raised
in the middle of handling rx irqs which resulted in an sk_buff memory
leak.
In addition, locking is spotty at best in the driver and inspection
revealed quite a few places with insufficient locking.
This patch is based on Asier's initial work, but reworks a number of
things so that locks are held for as short a time as possible, so
that spin_lock_irqsave() is used everywhere, and so the locks are
dropped when calling into the network stack (because the lock only
protects the hardware interface; not the network stack).
Boot tested on a lite5200 with an NFS root. Has not been performance
tested.
Signed-off-by: Asier Llano <a.llano@ziv.es>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more effective rss hash by default (src + dst, rather than just
src).
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is an updated version, because ixgbe_get_ethtool_stats()
needs to call dev_get_stats() or "ethtool -S" wont give
correct tx_bytes/tx_packets values.
Several cpus can update netdev->stats.tx_bytes & netdev->stats.tx_packets
in parallel. In this case, TX stats are under estimated and false sharing
takes place.
After a pktgen session sending exactly 200000000 packets :
# ifconfig fiber0 | grep TX
TX packets:198501982 errors:0 dropped:0 overruns:0 carrier:0
Multi queue devices should instead use txq->tx_bytes & txq->tx_packets
in their xmit() method (appropriate txq lock already held by caller, no
cache line miss), or use appropriate locking.
After patch, same pktgen session gives :
# ifconfig fiber0 | grep TX
TX packets:200000000 errors:0 dropped:0 overruns:0 carrier:0
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A workaround added for all ESB2 devices (adds a delay for all MDIC accesses
which resolves an issue with the MDIC ready bit being set prematurely) is
applicable only to devices in which the MAC-PHY interconnect is not
operating in a certain mode with in-band MDIO. Check the control register
for the operating mode and enable the workaround accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GG82563_REG() macro should not be used to determine the offset provided
to the e1000e_[read|write]_kmrn_reg() functions since the first argument to
the macro is already implied and gets masked off anyway in the functions.
The resultant register reads/writes with this patch are functionally the
same as before.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit 7 in the CTRL_REG register is actually the Software Definable Pin 3,
not the Software Definable Pin 7.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for the WiFi activity LED on the Dell Vostro A860 laptop.
Signed-off-by: Shahar Or <shahar@shahar-or.co.il>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A KERN_DEBUG didn't get removed when transitioning from printk to
pr_debug
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are different bits used to convey the setting of the rfkill
switch to the driver. The current driver only supports one of these
possibilities. These changes were derived from the latest version
of the vendor driver.
This patch fixes the regression noted in kernel Bugzilla #14743.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-and-tested-by: Antti Kaijanmäki <antti@kaijanmaki.net>
Tested-by: Hin-Tak Leung <hintak.leung@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in ath9k's tx status check, which
caused mac80211 to consider regularly transmitted unicast frames
as un-acked.
When checking the ts_status field for errors, it needs to be masked
with ATH9K_TXERR_FILT, because this field also contains other fields
like ATH9K_TX_ACKED.
Without this patch, AP mode is pretty much unusable, as hostapd
checks the ACK status for the frames that it injects.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The FINALIZE_JOIN firmware command only looks at the first couple of
fields in the beacon, and therefore it's not necessary to complain if
the beacon is longer than 128 bytes.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When disassociating, mac80211 zeroes vif->bss_info.bssid before
calling our ->bss_info_changed(), but we need the BSSID to remove the
hardware station database entry for our AP, so we can't clear our
local copy of the BSSID until after we've done that.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't forget to call pci_disable_device() if pci_request_regions()
fails during probe.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The time between loading the helper image and starting to upload the
main firmware image should be at least 5 ms or so. We were doing an
msleep(1) before, and 1 ms appears to not be enough in almost all
cases, but building with HZ=100 has always masked this so far. Bumping
the msleep argument to 5 fixes firmware loading e.g. when HZ=1000.
Some firmware images need more than 200ms to initialize. Bump the
ready code timeout to 500ms to accommodate for this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before issuing any firmware commands, we wait for the transmit rings
to drain, to prevent control versus data path synchronization issues.
In some cases, this can end up taking longer than the current hardcoded
limit of 5 seconds, for example if the transmit rings are filled with
packets for a host that has dropped off the air and we end up
retransmitting every pending packet at the lowest rate a couple of
times.
This patch changes mwl8k_tx_wait_empty() to only bail out on timeout
expiry if there was no change in the number of packets pending in the
transmit rings during the waiting period. If at least one transmit
ring entry was reclaimed while we were waiting, we are apparently still
making progress, and we'll allow waiting for another timeout period.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some firmware commands can under some circumstances take more than 2
seconds to complete. This patch bumps the timeout up to 10 seconds,
and prints a message whenever a command takes more than 2 seconds.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On 8366, bit 6 in the rx descriptor rate field indicates whether the
packet was received on a 20MHz or 40MHz channel, and is not part of
the MCS index. Handle this properly, which then prevents hitting the
WARN_ON and being dropped in ieee80211_rx().
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When inserting a DMA header into a packet for transmission,
mwl8k_add_dma_header() would blindly zero the addr4 field, which
is not a good idea if the packet being transmitted is actually a
4-address packet.
Also, if the transmitted packet was a 4-address with QoS packet,
the memmove() to do the needed header reshuffling would inadvertently
overwrite the first two bytes of the packet payload with the QoS field.
This fixes both of these issues.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Packets exchanged between the mwl8k driver and the firmware always
have a 4-address header without QoS field. For QoS packets, the QoS
field is passed to/from the firmware via the tx/rx descriptors.
We were handling this correctly on transmit, but not on receive -- if
a QoS packet was received, we would leave garbage in the QoS field in
the packet passed up to the stack, which is Bad(tm).
Also, if the packet received on the air was a 4-address without QoS
packet, we would forget to skb_pull the 2-byte DMA length prefix off.
This patch adds an argument to the ->rxd_process() receive descriptor
operation to retrieve the QoS field from the receive descriptor, and
extends mwl8k_remove_dma_header() to insert this field back into the
packet if the packet received is a QoS packet. It also fixes
mwl8k_remove_dma_header() to strip off the length prefix in all cases.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There exist 12 802.11b/g rates, but mwl8k supports two additional
(non-standard) rates, and includes those rates in rate bitmasks and
in its internal rate table that hardware rate indices index.
Commit "mwl8k: report rate and other information for received frames"
added one of the nonstandard rates to the mwl8k_rates table to make
the OFDM rates in the table line up with the rate indices that are
reported in the receive descriptor (so that we can just simply copy
the receive descriptor rate index into ieee80211_rx_status::rate_idx)
and bumped MWL8K_IEEE_LEGACY_DATA_RATES from 12 to 13, but this
screwed up the UPDATE_STADB command struct layout, as it also uses
that define, for its legacy_rates array.
To avoid having to convert rate indices and legacy rate bitmaps (e.g.
ieee80211_bss_conf::basic_rates) between the 12-rate mac80211 format
and the 14-rate mwl8k format, we'll report all 14 rates in our wiphy's
band, but filter out the nonstandard ones e.g. in the case of the
UPDATE_STADB command which only accepts 12 rates.
In the commands that accept 14 rates (SET_AID, SET_RATE), replace the
use of the MWL8K_RATE_INDEX_MAX_ARRAY define in the command struct by
the constant 14, to make it clearer that these commands accept 14 rates.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MCS bitmaps in the SET_RATE command structure were of the wrong
size, due to use of the wrong define for the array length. Just
hardcode the lengths as 16, and do the same for the MCS bitmaps in
other command structures.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bssid can be zero when null data template is set in wl1251_op_config().
It's enough, and especially safe, to set it once after association.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bssid needs to be copied first in wl1251_op_bss_info_changed(), otherwise
templates will have incorrect bssid and power save will not work
correctly.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a warning from wl1251_op_bss_info_changed():
wl1251: WARNING Set ctsprotect failed 0
It was printed always, it's completely false and can be removed.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/iwlwifi/iwl-tx.o
drivers/net/wireless/iwlwifi/iwl-tx.c: In function ‘iwl_tx_agg_stop’:
drivers/net/wireless/iwlwifi/iwl-tx.c:1356: warning: passing argument 1 of ‘ieee80211_stop_tx_ba_cb_irqsafe’ from incompatible pointer type
include/net/mac80211.h:2128: note: expected ‘struct ieee80211_vif *’ but argument is of type ‘struct ieee80211_hw *’
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Komuro pointed out that IRQ_FIRST_SHARED is not used at all in the
PCMCIA subsystem, so remove it. Also, remove two bogus assignments.
CC: Karsten Keil <keil@b1-systems.de>
CC: netdev@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
"Definition" is misspelled "defintion" in several comments; this
patch fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When debugging the wifi firmware, we need to disable the wimax core to gain
some memory space. The default value will keep the wimax core enabled.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wifi and wimax coexistence mode is set by wifi at boot time. There can be
several modes, defined by priority tables. User space components can decide
which one to select by writing to /sys/module/iwmc3200wifi/parameters/wiwi
with this patch, before bringing the interface up.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending the wiwi coexistence priority table, we should not tell the LMAC
that we want a response.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This update follows the firmware engineers recommendations.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver version number is a remnant from when there was an out-of-tree
iwlwifi driver. Now that the driver forms part of kernel source we do not
need a separate driver version. Instead, we now use the kernel version as
driver version. We maintain the previous tags used to indicate which
components the driver has been compiled with.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
error_event_table_ptr is only set upon receipt of REPLY_ALIVE. Until
then both event log and error log will fail. Add information to indicate
which uCode encounter the failure case.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the process of improving uCode event logging capability, the new
implementation was introduced without removing the existing
implementation. The event log will be dumped to dmesg twice.
Remove the old implementation to only log the event once upon sys
assert or request by user.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My gcc appears to be able to see past the function
boundary and notices that the variable 'behaviour'
could be used uninitialised:
drivers/net/wireless/b43/leds.c: In function ‘b43_leds_register’:
drivers/net/wireless/b43/leds.c:339: warning: ‘behaviour’ may be used uninitialized in this function
drivers/net/wireless/b43/leds.c: In function ‘b43_leds_init’:
drivers/net/wireless/b43/leds.c:262: warning: ‘behaviour’ may be used uninitialized in this function
because b43_led_get_sprominfo() didn't initialise
it in all cases.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add PCI .shutdown method so that we can disable the device during
shutdown or reboot. Without this, the reboot doesn't work well on
some platforms.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2124
Tested-by: pablo <pablolm2005@gmail.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When handling IWM_CMD_PMKID_FLUSH command, the bssid and
pmkid in pmksa are all NULL. Check it before memcpy.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the 2GHz band is enabled unconditionally, even if the device
does not support it.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On BigEndian gcc complains:
drivers/net/wireless/airo.c: In function ‘sniffing_mode’:
drivers/net/wireless/airo.c:4809: warning: integer overflow in expression
Fix this by doing the bitwise AND on the host-endian value.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While reviewing the l2pad function to align both the header and the payload
on a DMA-capable boundary a bug was discovered where the payload would not
be properly aligned. The header_align value was used where the payload_align
value should have been used.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For PPC architecture with PHY Revision < 3, a read of the register
B43_MMIO_HWENABLED_LO will cause a CPU fault unless b43legacy_status()
returns a value of 2 (B43legacy_STAT_STARTED); however, one finds that
the driver is unable to associate after resuming from hibernation unless
this routine returns 1. To satisfy both conditions, the routine is rewritten
to return TRUE whenever b43legacy_status() returns a value < 2.
This patch fixes the second problem listed in the postings for Red Hat
Bugzilla #538523.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The routine b43_is_hw_radio_enabled() has long been a problem.
For PPC architecture with PHY Revision < 3, a read of the register
B43_MMIO_HWENABLED_LO will cause a CPU fault unless b43_status()
returns a value of 2 (B43_STAT_STARTED) (BUG 14181). Fixing that
results in Bug 14538 in which the driver is unable to reassociate
after resuming from hibernation because b43_status() returns 0.
The correct fix would be to determine why the status is 0; however,
I have not yet found why that happens. The correct value is found for
my device, which has PHY revision >= 3.
Returning TRUE when the PHY revision < 3 and b43_status() returns 0 fixes
the regression for 2.6.32.
This patch fixes the problem in Red Hat Bugzilla #538523.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
fix some typos and punctuation in comments
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for ethtool selftest.
From: Suresh R <sureshr@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the NULL pointer dereference Oops in the ks8851 snl network
driver during transmission. All socket buffers from the queue are
processed inside the loop, but new workqueues have been scheduled to
run.
Signed-off-by: Tristram Ha <Tristram.Ha@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide common routine for the transition of operational state for a leaf
device during a root device transition.
Signed-off-by: Patrick Mullaney <pmullaney@novell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Replace magic values with constants
- Simplify length calculation and fix a bug
Based on valuable feedback from Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when disabling interrupts, driver was writing with IO, this is no
necessary because on ixgbe parts the hardware can "oneshot"
disable and clear the interrupt. So on 82598/82599 use of EIAM
should avoid one posted write per interrupt when in MSI-X mode.
This should improve performance and seems to in my limited
testing, reduce CPU utilization VERY slightly.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drop variables that had cache lines modified in simultaneous hot paths.
keep some variables modified on hot paths but make their storage per queue.
cache align DMA data buffer start addresses.
cache align (padding) some structures that end within a cacheline.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
decrease the memory utilization of the tx / rx queue allocation
by changing the default ring size to 512 (from 1024). At
1024 rx entries of 2KB each (from 4kB slab) with 16 queues
ixgbe was using 64 MB of memory per port, which is not
necessary.
Users can still change queue lengths with ethtool -k.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the Tx queue selection for FCoE traffic from ixgbe_xmit_frame()
and does it in the ndo_select_queue() call, moving all Tx queue selection
into a single routine.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the user priority for FCoE and use it directly for outgoing
FCoE traffic when DCB is enabled.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using remote wakeup and delayed transmission to allow
online device to go into usb autosuspend.
Minimal alternate support for devices that don't support
remote wakeup.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normal resume can do double duty as reset_resume() for this driver
as it keeps no state in the device
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To help debug the problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prevent race conditions with other reset events.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.105.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tg3's firmware is no longer loaded from tg3_init_one(). Remove the
error path that releases the firmware back to the system.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver needs to use PCI configuration space to read the VPD data,
the accesses could collide with the pci_read_vpd() function. This patch
converts the driver to use pci_read_vpd() to avoid any potential
collisions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the VPD code by creating preprocessor definitions
and using them in the place of hardcoded constants.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 57765 asic revision.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 57765 asic rev has MSI-X capability, but does not support TSS. This
patch changes the tx paths so that TSS is explicitly mentioned, rather
than implied through the ENABLE_MSIX flag.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for WOL using Magic Packet after suspend is done.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a firmware command fails, only the failure codes are printed.
It is difficult to co-relate this to the actual command that has failed.
These changes will now print the command code that has failed.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix dma-api-checking warnings in Sun HME
Sun HME driver is mapping the first fragment with dma_map_single and subsequent
fragments with dma_map_page. It is unmapping all fragments with dma_unmap_single
and that produces the warning.
This patch changes it so that it unmaps only the first fragment with
dma_unmap_single and subsequent fragments are unmapped with dma_unmap_page.
WARNING: at lib/dma-debug.c:816 check_unmap+0x3ac/0x780()
hme 0000:01:01.1: DMA-API: device driver frees DMA memory with wrong function [device address=0x00000000c1082000] [size=32 bytes] [mapped as page] [unmapped as single]
Modules linked in: nbd sunhme openpromfs sermouse unix
Call Trace:
[0000000000456910] warn_slowpath_common+0x50/0xa0
[0000000000571f4c] check_unmap+0x3ac/0x780
[0000000000572570] debug_dma_unmap_page+0x50/0x60
[000000001002f5fc] happy_meal_tx+0x11c/0x260 [sunhme]
[000000001002fc4c] happy_meal_interrupt+0xcc/0xe0 [sunhme]
[0000000000492d94] handle_fasteoi_irq+0x74/0x100
[000000000042ac0c] handler_irq+0xcc/0x100
[0000000000426a54] valid_addr_bitmap_patch+0x14/0x1c0
[0000000000665de0] _spin_unlock_irqrestore+0x40/0x60
[0000000000462bb8] mod_timer+0x118/0x1a0
[00000000005ec254] sk_reset_timer+0x14/0x40
[0000000000635e4c] tcp_event_new_data_sent+0x8c/0xc0
[0000000000639374] __tcp_push_pending_frames+0x34/0xc0
---[ end trace 73d5c42c1e9f11c4 ]---
Mapped at:
[<000000001002f148>] happy_meal_start_xmit+0x308/0x480 [sunhme]
[<00000000005fc858>] dev_hard_start_xmit+0x318/0x3c0
[<000000000060fec4>] sch_direct_xmit+0x1a4/0x200
[<00000000005fced0>] dev_queue_xmit+0x410/0x560
[<0000000000604a1c>] neigh_resolve_output+0xfc/0x300
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unimplemented operations should not silently fail.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions provide the default behaviour and do not need to be
set in struct ethtool_ops.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace pci_alloc_consistent() with dma_alloc_coherent() so that
appropriate GFP flags can be used.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old code mistakenly zeroed out the upper 32-bit of the DMA address.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix code to read the proper iSCSI MAC address for bnx2x devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to send a HALT command to the firmware to fully shutdown the bnx2x
rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old code was initializing the ring producers using an incorrect I/O
address.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle few corner cases in firmware hang detection and recovery:
o Don't mark device state as READY, till handshake with
firmware is done.
o During probe, if start_firmware fails, restore reference
count.
o Don't increment refernce count, if start_firmware fails
during firmware reset.
o Clear __NX_RESETTING bit, incase of fatal error or tempeature
reaches critical limit so that pci remove() doesn't poll on
this bit.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver maps only some part of the MMIO bar 0 in case of
NX2031. This is sufficient for tx and rx by the driver.
When debug tools need to access resources in
unmapped regions, driver needs to map these on the fly
in order to complete read/write request.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some function pointers for a few PHY operations (for 82578 and 82567) and
were set incorrectly causing functions to be executed that were accessing
incorrect PHY register offsets for that particular device. This patch also
moves a few PHY-specific functions from ich8lan.c to the more appropriate
phy.c.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workaround that detects the correct PHY ID when an initial read of the
PHY ID registers returns an invalid one should retry up to ten times with
a small delay between attempts using a single PHY address and then repeat
using the remaining possible PHY addresses. Do this instead of trying each
possible PHY address repeating that up to 100 times.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function pointers for 8257x devices are not set. This is not really a
problem now because there is nothing in the driver that references the
pointers for this particular MAC-family (the appropriate functions are
called directly), but the pointers should be set in case they are used in
the future.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the fact that skb_dma_map/unmap do not work correctly when a HW
IOMMU is enabled it has been recommended to go about removing the calls
from the network device drivers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the fact that skb_dma_map/unmap do not work correctly when a HW
IOMMU is enabled it has been recommended to go about removing the calls
from the network device drivers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the fact that skb_dma_map/unmap do not work correctly when a HW
IOMMU is enabled it has been recommended to go about removing the calls
from the network device drivers.
[ Fix bnx2_free_tx_skbs() ring indexing and use NETDEV_TX_OK return
code in bnx2_start_xmit() after cleaning up DMA mapping errors. -Mchan ]
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the skb_dma_map/unmap calls from the igbvf driver due to
the fact that it does not play well with HW IOMMU when combined with
transmitting cloned skbs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change removes skb_dma_map/unmap calls from the igb driver due to the
fact that the call is incompatible with iommu enabled kernels. In order to
prevent warnings about using the wrong unmap call I have added a
mapped_as_page value to the buffer_info structure to track if the mapped
region is a page or a buffer.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes skb_dma_map/unmap calls from the ixgbe driver due to the
fact that the calls don't work with HW IOMMU enabled systems. The problem
is that multiple mappings will give different results when HW IOMMU is
enabled and the skb_dma_map/unmap calls only have one location to store
mappings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_dma_map is incompatible with HW iommu due to the fact that multiple
mappings can result in different results each time. For this reason it is
best to just remove use of these function calls.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the use of skb_dma_map from the e1000 driver in order to avoid
issues when HW iommu are in use.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In testing we have found that skb_dma_map/unmap is incompatible with HW
IOMMU due to the fact that multiple mappings will return different results.
In order to correct this we need to remove skb_dma_map/unmap calls from the
e1000e driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2 is failing when a PCI error is detected. The error is the
following:
bnx2: Chip not in correct endian mode
bnx2: fw sync timeout, reset code = 404001d
This error was caused because the way pci_restore_state() is working
after commit 4b77b0a2ba ("PCI: Clear
saved_state after the state has been restored").
Signed-off-by: Breno Leitao<leitao@linux.vnet.ibm.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed braces position on some statements.
Inserted a space between an "if" keyword and a parenthesis.
Signed-off-by: Rudy Matela <rudy.matela@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool_ops.set_settings support to the PS3 gelic network driver.
Allows manual setting of ethernet link speed.
Signed-off-by: Hideyuki Sasaki <xhide@rd.scei.sony.co.jp>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup of the gelic driver enumerations:
o Add some missing commas.
o Add an Ether port post fix (PS3 currently only supports PORT_0).
o Add a new enum gelic_lv1_phy to use when interacting with the PHY.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every time while doing ethtool->get_settings we are accessing
the hardware to get link status and port information.
This is not necessary. We now use the cached copy for this info
and update it when the link status changes.
From: Suresh R <sureshr@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add be_rx_polls to count number of times NAPI called rx poll function.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
port identification/beaconing is failing if device open has not been done.
Fixing it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow only valid ether addresses to be assigned and used for the interface.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
patch to initialize netdev->vlan_features appropriately.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For hardware limit to support TSOV6, just disable this feature
Signed-off-by: Jie Yang <jie.yang@atheros.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use the sizeof the pointer to clear the result
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the case for 82577 because it does not support the ability to check
for downshift. Add case for e1000_phy_bm which can do this.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some helpful debug messages.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new PCI device ID is for a new combination of MAC and PHY both of
which already have supporting code in the driver, just not yet in this
combination. During validation of the device, an intermittent issue was
discovered with waking it from a suspended state which can be resolved with
the pre-existing workaround to disable gigabit speed prior to suspending.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures that the link state (as reported in
mac->serdes_has_link) will transition to false when autoneg fails to
complete but valid codewords were detected.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The different families (80003es2lan, 8257x, ICHx/PCH) supported by the
driver each have their own conditions when the PHY can be powered down.
This patch rewrites the PHY power up/down code to fit with the family-
specific style used in the driver. All pre-existing calls to power up or
down the PHY remain untouched. A new call to power down the PHY when
removing the driver when the interface is down replaces the current call
to reset the PHY in order to reduce power consumption.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two MAC-families that have VLAN filter table register arrays manage
each a bit differently from one another, so provide family-specific
functions for managing the register arrays and function pointers to access
the appropriate function. Also make sure attempts to access these
register arrays are not done on parts not supporting that feature.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take advantage of the new pernet automatic storage management,
and stop using compatibility network namespace functions.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take advantage of the new pernet automatic storage management,
and stop using compatibility network namespace functions.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take advantage of the new pernet automatic storage management,
and stop using compatibility network namespace functions.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take advantage of the new pernet automatic storage management,
and stop using compatibility network namespace functions.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defer calling unregister_netdevice_queue to cleanup_net. It's simpler
and it allows the loopback device to land in the same batch as other
network devices.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lennert Buytenhek noticed that delBA handling in mac80211
was broken and has remotely triggerable problems, some of
which are due to some code shuffling I did that ended up
changing the order in which things were done -- this was
commit d75636ef9c
Author: Johannes Berg <johannes@sipsolutions.net>
Date: Tue Feb 10 21:25:53 2009 +0100
mac80211: RX aggregation: clean up stop session
and other parts were already present in the original
commit d92684e660
Author: Ron Rindjunsky <ron.rindjunsky@intel.com>
Date: Mon Jan 28 14:07:22 2008 +0200
mac80211: A-MPDU Tx add delBA from recipient support
The first problem is that I moved a BUG_ON before various
checks -- thereby making it possible to hit. As the comment
indicates, the BUG_ON can be removed since the ampdu_action
callback must already exist when the state is != IDLE.
The second problem isn't easily exploitable but there's a
race condition due to unconditionally setting the state to
OPERATIONAL when a delBA frame is received, even when no
aggregation session was ever initiated. All the drivers
accept stopping the session even then, but that opens a
race window where crashes could happen before the driver
accepts it. Right now, a WARN_ON may happen with non-HT
drivers, while the race opens only for HT drivers.
For this case, there are two things necessary to fix it:
1) don't process spurious delBA frames, and be more careful
about the session state; don't drop the lock
2) HT drivers need to be prepared to handle a session stop
even before the session was really started -- this is
true for all drivers (that support aggregation) but
iwlwifi which can be fixed easily. The other HT drivers
(ath9k and ar9170) are behaving properly already.
Reported-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes kernel bugzilla #14691
Due to the way netpoll works, it is perfectly legal to see
NAPI already scheduled when new device events are pending
in b44_interrupt().
So logging a message about it is wrong and in fact harmful.
Based upon a patch by Andreas Mohr.
Signed-off-by: David S. Miller <davem@davemloft.net>
The other paths all drop chan->wsem. This was found by a static
checker (smatch).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jan "Yenya" Kasprzak <kas@fi.muni.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we happen to have registered the driver without passing
a MAC address, we will print a zero MAC address and register
the interface with this invalid address, this is confusin. This
patch moves the checking of a valid ethernet address and the
generation of a random one down from the open function to
the probe function.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
smc91x.h defines SMC_IRQ_FLAGS to be -1 when it wants the interrupt
flags to be taken from the resource structure. However, d280ead
changed this to checking for non-zero resource flags.
Unfortunately, this means that on some platforms, we end up passing
'-1' to request_irq rather than the desired result. Combine the two
conditions into one so that the IRQ flags are taken from the resource
if either SMC_IRQ_FLAGS is -1 or the resource flags specify an
interrupt trigger.
This restores network on at least the Versatile platform.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a space separating some if keywords from the following
parenthesis to conform to the CodingStyle.
Signed-off-by: Rudy Matela <rudy.matela@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a space separating some keywords (if/while) from the following
parenthesis to conform to the CodingStyle.
Signed-off-by: Rudy Matela <rudy.matela@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a null pointer dereference BUG() if ethtool is used on
an smsc9420 interface while it is down, because the phy_dev is only
allocated while the interface is up.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newer chipsets (all PCI-E) are known that they need full power cycle
(AC or battery removal) to reset MAC address to a hardwired one. Previous
patch to address this problem loads the original MAC address from EEPROM.
But it brought other problem for which it is necessary to introduce a new
module parameter.
However, it might suffice to restore the initial MAC address before
shutdown/reboot/kexec and when removing the module.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch "fix memory initialization:5d521fd36de4e61" didn't got merge.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver has been mostly rewritten since Michael Brown's initial
work, so swap the order of the authors.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This integrates support for the SFC9000 family of 10G Ethernet
controllers and LAN-on-motherboard chips, starting with the SFL9021
'Siena' and SFC9020 'Bethpage'.
Credit for this code is largely due to my colleagues at Solarflare:
Guido Barzini
Steve Hodgson
Kieran Mansley
Matthew Slattery
Neil Turton
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the SFC9000 family of 10G Ethernet controllers
and LAN-on-motherboard chips, starting with the SFL9021 'Siena' and
SFC9020 'Bethpage'.
The SFC9000 family is based on the SFC4000 'Falcon' architecture, but
with some significant changes:
- Two ports are associated with two independent PCI functions
(except SFC9010)
- Integrated 10GBASE-T PHY(s) (SFL9021/9022)
- MAC, PHY and board peripherals are managed by firmware
- Driver does not require board-specific code
- Firmware supports wake-on-LAN and lights-out management through NC-SI
- IPv6 checksum offload and RSS
- Filtering by MAC address and VLAN (not included in this code)
- PCI SR-IOV (not included in this code)
Credit for this code is largely due to my colleagues at Solarflare:
Guido Barzini
Steve Hodgson
Kieran Mansley
Matthew Slattery
Neil Turton
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In new NICs flash is managed by firmware and we will use high-level
operations on partitions rather than direct SPI commands. Add support
for multiple MTD partitions per flash device and remove the direct
link between MTD and SPI devices. Maintain a list of MTD partitions
in struct efx_nic.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New NICs have firmware managing the PHY, and we will discover the PHY
capabilities at run-time. Replace the static data with probe() and
test_name() operations.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New NICs and PHYs support a wider variety of loopback modes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
falcon_probe_nic_variant() does a lot less than it used to, and a
lot less than it claims to. Fold the remainder into its caller.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_alloc_consistent uses GFP_ATOMIC allocation that may fail on some systems
with limited memory (Bug #14265). pci_pool_alloc allows waiting with
GFP_KERNEL.
Tested-by: Karol Lewandowski <karol.k.lewandowski@gmail.com>
Signed-off-by: Roger Oksanen <roger.oksanen@cs.helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor efx_reset_down() and efx_reset_up() accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sujith